On a Chromebook I'm working on I noticed a big (~1 second) delay
during bootup where nothing was happening. Right around this big
delay there were messages about the TPM:
[ 2.311352] tpm_tis_spi spi0.0: TPM ready IRQ confirmed on attempt 2
[ 3.332790] tpm_tis_spi spi0.0: Cr50 firmware version: ...
I put a few printouts in and saw that tpm_tis_spi_init() (specifically
tpm_chip_register() in that function) was taking the lion's share of
this time, though ~115 ms of the time was in cr50_print_fw_version().
Let's make a one-line change to prefer async probe for tpm_tis_spi.
There's no reason we need to block other drivers from probing while we
load.
NOTES:
* It's possible that other hardware runs through the init sequence
faster than Cr50 and this isn't such a big problem for them.
However, even if they are faster they are still doing _some_
transfers over a SPI bus so this should benefit everyone even if to
a lesser extent.
* It's possible that there are extra delays in the code that could be
optimized out. I didn't dig since once I enabled async probe they
no longer impacted me.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
The tpm2_get_cc_attrs_tbl() call will result in TPM commands being issued,
which will need the use of the internal command/response buffer. But,
we're issuing this *before* we've waited to make sure that buffer is
allocated.
This can result in intermittent failures to probe if the hypervisor / TPM
implementation doesn't respond quickly enough. I find it fails almost
every time with an 8 vcpu guest under KVM with software emulated TPM.
To fix it, just move the tpm2_get_cc_attrs_tlb() call after the
existing code to wait for initialization, which will ensure the buffer
is allocated.
Fixes: 18b3670d79 ("tpm: ibmvtpm: Add support for TPM2")
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Trivial fix, the spelling of "drescription" is incorrect
in function comment.
Fix this.
Signed-off-by: Binbin Zhou <zhoubinbin@uniontech.com>
Acked-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Found by smatch:
drivers/char/tpm/tpm_tis_core.c:1088 tpm_tis_core_init() warn:
variable dereferenced before check 'chip->ops' (see line 979)
'chip->ops' is assigned in the beginning of function
in tpmm_chip_alloc->tpm_chip_alloc
and is used before first possible goto to error path.
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
During flow control we are just reading from the TPM, yet our spi_xfer
has the tx_buf and rx_buf both non-NULL which means we're requesting a
full duplex transfer.
SPI is always somewhat of a full duplex protocol anyway and in theory
the other side shouldn't really be looking at what we're sending it
during flow control, but it's still a bit ugly to be sending some
"random" data when we shouldn't.
The default tpm_tis_spi_flow_control() tries to address this by
setting 'phy->iobuf[0] = 0'. This partially avoids the problem of
sending "random" data, but since our tx_buf and rx_buf both point to
the same place I believe there is the potential of us sending the
TPM's previous byte back to it if we hit the retry loop.
Another flow control implementation, cr50_spi_flow_control(), doesn't
address this at all.
Let's clean this up and just make the tx_buf NULL before we call
flow_control(). Not only does this ensure that we're not sending any
"random" bytes but it also possibly could make the SPI controller
behave in a slightly more optimal way.
NOTE: no actual observed problems are fixed by this patch--it's was
just made based on code inspection.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
It has been reported that some TIS based TPMs are giving unexpected
errors when using the O_NONBLOCK path of the TPM device. The problem
is that some TPMs don't like it when you get and then relinquish a
locality (as the tpm_try_get_ops()/tpm_put_ops() pair does) without
sending a command. This currently happens all the time in the
O_NONBLOCK write path. Fix this by moving the tpm_try_get_ops()
further down the code to after the O_NONBLOCK determination is made.
This is safe because the priv->buffer_mutex still protects the priv
state being modified.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=206275
Fixes: d23d124843 ("tpm: fix invalid locking in NONBLOCKING mode")
Reported-by: Mario Limonciello <Mario.Limonciello@dell.com>
Tested-by: Alex Guzman <alex@guzman.io>
Cc: stable@vger.kernel.org
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
pm_runtime_get_sync() increments the runtime PM usage counter even
the call returns an error code. Thus a pairing decrement is needed
on the error handling path to keep the counter balanced.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Since commit 84af7a6194 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.
This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.
There are a variety of indentation styles found.
a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'
In order to convert all of them to 1 tab + 'help', I ran the
following commend:
$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Pull sysctl fixes from Al Viro:
"Fixups to regressions in sysctl series"
* 'work.sysctl' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
sysctl: reject gigantic reads/write to sysctl files
cdrom: fix an incorrect __user annotation on cdrom_sysctl_info
trace: fix an incorrect __user annotation on stack_trace_sysctl
random: fix an incorrect __user annotation on proc_do_entropy
net/sysctl: remove leftover __user annotations on neigh_proc_dointvec*
net/sysctl: use cpumask_parse in flow_limit_cpu_sysctl
Patch series "mm: consolidate definitions of page table accessors", v2.
The low level page table accessors (pXY_index(), pXY_offset()) are
duplicated across all architectures and sometimes more than once. For
instance, we have 31 definition of pgd_offset() for 25 supported
architectures.
Most of these definitions are actually identical and typically it boils
down to, e.g.
static inline unsigned long pmd_index(unsigned long address)
{
return (address >> PMD_SHIFT) & (PTRS_PER_PMD - 1);
}
static inline pmd_t *pmd_offset(pud_t *pud, unsigned long address)
{
return (pmd_t *)pud_page_vaddr(*pud) + pmd_index(address);
}
These definitions can be shared among 90% of the arches provided
XYZ_SHIFT, PTRS_PER_XYZ and xyz_page_vaddr() are defined.
For architectures that really need a custom version there is always
possibility to override the generic version with the usual ifdefs magic.
These patches introduce include/linux/pgtable.h that replaces
include/asm-generic/pgtable.h and add the definitions of the page table
accessors to the new header.
This patch (of 12):
The linux/mm.h header includes <asm/pgtable.h> to allow inlining of the
functions involving page table manipulations, e.g. pte_alloc() and
pmd_alloc(). So, there is no point to explicitly include <asm/pgtable.h>
in the files that include <linux/mm.h>.
The include statements in such cases are remove with a simple loop:
for f in $(git grep -l "include <linux/mm.h>") ; do
sed -i -e '/include <asm\/pgtable.h>/ d' $f
done
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Cain <bcain@codeaurora.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Ungerer <gerg@linux-m68k.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Guo Ren <guoren@kernel.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Mike Rapoport <rppt@kernel.org>
Cc: Nick Hu <nickhu@andestech.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Stafford Horne <shorne@gmail.com>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vincent Chen <deanbo422@gmail.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Will Deacon <will@kernel.org>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Link: http://lkml.kernel.org/r/20200514170327.31389-1-rppt@kernel.org
Link: http://lkml.kernel.org/r/20200514170327.31389-2-rppt@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
No user pointers for sysctls anymore.
Fixes: 32927393dc ("sysctl: pass kernel pointers to ->proc_handler")
Reported-by: build test robot <lkp@intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Here is the large set of char/misc driver patches for 5.8-rc1
Included in here are:
- habanalabs driver updates, loads
- mhi bus driver updates
- extcon driver updates
- clk driver updates (approved by the clock maintainer)
- firmware driver updates
- fpga driver updates
- gnss driver updates
- coresight driver updates
- interconnect driver updates
- parport driver updates (it's still alive!)
- nvmem driver updates
- soundwire driver updates
- visorbus driver updates
- w1 driver updates
- various misc driver updates
In short, loads of different driver subsystem updates along with the
drivers as well.
All have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXtzkHw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yldOwCgus/DgpnI1UL4z+NdBxJrAXtkPmgAn2sgTUea
i5RblCmcVMqvHaGtYkY+
=tScN
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the large set of char/misc driver patches for 5.8-rc1
Included in here are:
- habanalabs driver updates, loads
- mhi bus driver updates
- extcon driver updates
- clk driver updates (approved by the clock maintainer)
- firmware driver updates
- fpga driver updates
- gnss driver updates
- coresight driver updates
- interconnect driver updates
- parport driver updates (it's still alive!)
- nvmem driver updates
- soundwire driver updates
- visorbus driver updates
- w1 driver updates
- various misc driver updates
In short, loads of different driver subsystem updates along with the
drivers as well.
All have been in linux-next for a while with no reported issues"
* tag 'char-misc-5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (233 commits)
habanalabs: correctly cast u64 to void*
habanalabs: initialize variable to default value
extcon: arizona: Fix runtime PM imbalance on error
extcon: max14577: Add proper dt-compatible strings
extcon: adc-jack: Fix an error handling path in 'adc_jack_probe()'
extcon: remove redundant assignment to variable idx
w1: omap-hdq: print dev_err if irq flags are not cleared
w1: omap-hdq: fix interrupt handling which did show spurious timeouts
w1: omap-hdq: fix return value to be -1 if there is a timeout
w1: omap-hdq: cleanup to add missing newline for some dev_dbg
/dev/mem: Revoke mappings when a driver claims the region
misc: xilinx-sdfec: convert get_user_pages() --> pin_user_pages()
misc: xilinx-sdfec: cleanup return value in xsdfec_table_write()
misc: xilinx-sdfec: improve get_user_pages_fast() error handling
nvmem: qfprom: remove incorrect write support
habanalabs: handle MMU cache invalidation timeout
habanalabs: don't allow hard reset with open processes
habanalabs: GAUDI does not support soft-reset
habanalabs: add print for soft reset due to event
habanalabs: improve MMU cache invalidation code
...
A few small fixes for things, nothing earth shattering.
-corey
-----BEGIN PGP SIGNATURE-----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=nuZ5
-----END PGP SIGNATURE-----
Merge tag 'for-linus-5.8-1' of git://github.com/cminyard/linux-ipmi
Pull IPMI updates from Corey Minyard:
"A few small fixes for things, nothing earth shattering"
* tag 'for-linus-5.8-1' of git://github.com/cminyard/linux-ipmi:
ipmi:ssif: Remove dynamic platform device handing
Try to load acpi_ipmi when an SSIF ACPI IPMI interface is added
ipmi_si: Load acpi_ipmi when ACPI IPMI interface added
ipmi:bt-bmc: Fix error handling and status check
ipmi: Replace guid_copy() with import_guid() where it makes sense
ipmi: use vzalloc instead of kmalloc for user creation
ipmi:bt-bmc: Fix some format issue of the code
ipmi:bt-bmc: Avoid unnecessary check
- Support for userspace to send requests directly to the on-chip GZIP
accelerator on Power9.
- Rework of our lockless page table walking (__find_linux_pte()) to make it
safe against parallel page table manipulations without relying on an IPI for
serialisation.
- A series of fixes & enhancements to make our machine check handling more
robust.
- Lots of plumbing to add support for "prefixed" (64-bit) instructions on
Power10.
- Support for using huge pages for the linear mapping on 8xx (32-bit).
- Remove obsolete Xilinx PPC405/PPC440 support, and an associated sound driver.
- Removal of some obsolete 40x platforms and associated cruft.
- Initial support for booting on Power10.
- Lots of other small features, cleanups & fixes.
Thanks to:
Alexey Kardashevskiy, Alistair Popple, Andrew Donnellan, Andrey Abramov,
Aneesh Kumar K.V, Balamuruhan S, Bharata B Rao, Bulent Abali, Cédric Le
Goater, Chen Zhou, Christian Zigotzky, Christophe JAILLET, Christophe Leroy,
Dmitry Torokhov, Emmanuel Nicolet, Erhard F., Gautham R. Shenoy, Geoff Levand,
George Spelvin, Greg Kurz, Gustavo A. R. Silva, Gustavo Walbon, Haren Myneni,
Hari Bathini, Joel Stanley, Jordan Niethe, Kajol Jain, Kees Cook, Leonardo
Bras, Madhavan Srinivasan., Mahesh Salgaonkar, Markus Elfring, Michael
Neuling, Michal Simek, Nathan Chancellor, Nathan Lynch, Naveen N. Rao,
Nicholas Piggin, Oliver O'Halloran, Paul Mackerras, Pingfan Liu, Qian Cai, Ram
Pai, Raphael Moreira Zinsly, Ravi Bangoria, Sam Bobroff, Sandipan Das, Segher
Boessenkool, Stephen Rothwell, Sukadev Bhattiprolu, Tyrel Datwyler, Wolfram
Sang, Xiongfeng Wang.
-----BEGIN PGP SIGNATURE-----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=o0WU
-----END PGP SIGNATURE-----
Merge tag 'powerpc-5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
- Support for userspace to send requests directly to the on-chip GZIP
accelerator on Power9.
- Rework of our lockless page table walking (__find_linux_pte()) to
make it safe against parallel page table manipulations without
relying on an IPI for serialisation.
- A series of fixes & enhancements to make our machine check handling
more robust.
- Lots of plumbing to add support for "prefixed" (64-bit) instructions
on Power10.
- Support for using huge pages for the linear mapping on 8xx (32-bit).
- Remove obsolete Xilinx PPC405/PPC440 support, and an associated sound
driver.
- Removal of some obsolete 40x platforms and associated cruft.
- Initial support for booting on Power10.
- Lots of other small features, cleanups & fixes.
Thanks to: Alexey Kardashevskiy, Alistair Popple, Andrew Donnellan,
Andrey Abramov, Aneesh Kumar K.V, Balamuruhan S, Bharata B Rao, Bulent
Abali, Cédric Le Goater, Chen Zhou, Christian Zigotzky, Christophe
JAILLET, Christophe Leroy, Dmitry Torokhov, Emmanuel Nicolet, Erhard F.,
Gautham R. Shenoy, Geoff Levand, George Spelvin, Greg Kurz, Gustavo A.
R. Silva, Gustavo Walbon, Haren Myneni, Hari Bathini, Joel Stanley,
Jordan Niethe, Kajol Jain, Kees Cook, Leonardo Bras, Madhavan
Srinivasan., Mahesh Salgaonkar, Markus Elfring, Michael Neuling, Michal
Simek, Nathan Chancellor, Nathan Lynch, Naveen N. Rao, Nicholas Piggin,
Oliver O'Halloran, Paul Mackerras, Pingfan Liu, Qian Cai, Ram Pai,
Raphael Moreira Zinsly, Ravi Bangoria, Sam Bobroff, Sandipan Das, Segher
Boessenkool, Stephen Rothwell, Sukadev Bhattiprolu, Tyrel Datwyler,
Wolfram Sang, Xiongfeng Wang.
* tag 'powerpc-5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (299 commits)
powerpc/pseries: Make vio and ibmebus initcalls pseries specific
cxl: Remove dead Kconfig options
powerpc: Add POWER10 architected mode
powerpc/dt_cpu_ftrs: Add MMA feature
powerpc/dt_cpu_ftrs: Enable Prefixed Instructions
powerpc/dt_cpu_ftrs: Advertise support for ISA v3.1 if selected
powerpc: Add support for ISA v3.1
powerpc: Add new HWCAP bits
powerpc/64s: Don't set FSCR bits in INIT_THREAD
powerpc/64s: Save FSCR to init_task.thread.fscr after feature init
powerpc/64s: Don't let DT CPU features set FSCR_DSCR
powerpc/64s: Don't init FSCR_DSCR in __init_FSCR()
powerpc/32s: Fix another build failure with CONFIG_PPC_KUAP_DEBUG
powerpc/module_64: Use special stub for _mcount() with -mprofile-kernel
powerpc/module_64: Simplify check for -mprofile-kernel ftrace relocations
powerpc/module_64: Consolidate ftrace code
powerpc/32: Disable KASAN with pages bigger than 16k
powerpc/uaccess: Don't set KUEP by default on book3s/32
powerpc/uaccess: Don't set KUAP by default on book3s/32
powerpc/8xx: Reduce time spent in allow_user_access() and friends
...
Pull networking updates from David Miller:
1) Allow setting bluetooth L2CAP modes via socket option, from Luiz
Augusto von Dentz.
2) Add GSO partial support to igc, from Sasha Neftin.
3) Several cleanups and improvements to r8169 from Heiner Kallweit.
4) Add IF_OPER_TESTING link state and use it when ethtool triggers a
device self-test. From Andrew Lunn.
5) Start moving away from custom driver versions, use the globally
defined kernel version instead, from Leon Romanovsky.
6) Support GRO vis gro_cells in DSA layer, from Alexander Lobakin.
7) Allow hard IRQ deferral during NAPI, from Eric Dumazet.
8) Add sriov and vf support to hinic, from Luo bin.
9) Support Media Redundancy Protocol (MRP) in the bridging code, from
Horatiu Vultur.
10) Support netmap in the nft_nat code, from Pablo Neira Ayuso.
11) Allow UDPv6 encapsulation of ESP in the ipsec code, from Sabrina
Dubroca. Also add ipv6 support for espintcp.
12) Lots of ReST conversions of the networking documentation, from Mauro
Carvalho Chehab.
13) Support configuration of ethtool rxnfc flows in bcmgenet driver,
from Doug Berger.
14) Allow to dump cgroup id and filter by it in inet_diag code, from
Dmitry Yakunin.
15) Add infrastructure to export netlink attribute policies to
userspace, from Johannes Berg.
16) Several optimizations to sch_fq scheduler, from Eric Dumazet.
17) Fallback to the default qdisc if qdisc init fails because otherwise
a packet scheduler init failure will make a device inoperative. From
Jesper Dangaard Brouer.
18) Several RISCV bpf jit optimizations, from Luke Nelson.
19) Correct the return type of the ->ndo_start_xmit() method in several
drivers, it's netdev_tx_t but many drivers were using
'int'. From Yunjian Wang.
20) Add an ethtool interface for PHY master/slave config, from Oleksij
Rempel.
21) Add BPF iterators, from Yonghang Song.
22) Add cable test infrastructure, including ethool interfaces, from
Andrew Lunn. Marvell PHY driver is the first to support this
facility.
23) Remove zero-length arrays all over, from Gustavo A. R. Silva.
24) Calculate and maintain an explicit frame size in XDP, from Jesper
Dangaard Brouer.
25) Add CAP_BPF, from Alexei Starovoitov.
26) Support terse dumps in the packet scheduler, from Vlad Buslov.
27) Support XDP_TX bulking in dpaa2 driver, from Ioana Ciornei.
28) Add devm_register_netdev(), from Bartosz Golaszewski.
29) Minimize qdisc resets, from Cong Wang.
30) Get rid of kernel_getsockopt and kernel_setsockopt in order to
eliminate set_fs/get_fs calls. From Christoph Hellwig.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2517 commits)
selftests: net: ip_defrag: ignore EPERM
net_failover: fixed rollback in net_failover_open()
Revert "tipc: Fix potential tipc_aead refcnt leak in tipc_crypto_rcv"
Revert "tipc: Fix potential tipc_node refcnt leak in tipc_rcv"
vmxnet3: allow rx flow hash ops only when rss is enabled
hinic: add set_channels ethtool_ops support
selftests/bpf: Add a default $(CXX) value
tools/bpf: Don't use $(COMPILE.c)
bpf, selftests: Use bpf_probe_read_kernel
s390/bpf: Use bcr 0,%0 as tail call nop filler
s390/bpf: Maintain 8-byte stack alignment
selftests/bpf: Fix verifier test
selftests/bpf: Fix sample_cnt shared between two threads
bpf, selftests: Adapt cls_redirect to call csum_level helper
bpf: Add csum_level helper for fixing up csum levels
bpf: Fix up bpf_skb_adjust_room helper's skb csum setting
sfc: add missing annotation for efx_ef10_try_update_nic_stats_vf()
crypto/chtls: IPv6 support for inline TLS
Crypto/chcr: Fixes a coccinile check error
Crypto/chcr: Fixes compilations warnings
...
Pull uaccess/access_ok updates from Al Viro:
"Removals of trivially pointless access_ok() calls.
Note: the fiemap stuff was removed from the series, since they are
duplicates with part of ext4 series carried in Ted's tree"
* 'uaccess.access_ok' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
vmci_host: get rid of pointless access_ok()
hfi1: get rid of pointless access_ok()
usb: get rid of pointless access_ok() calls
lpfc_debugfs: get rid of pointless access_ok()
efi_test: get rid of pointless access_ok()
drm_read(): get rid of pointless access_ok()
via-pmu: don't bother with access_ok()
drivers/crypto/ccp/sev-dev.c: get rid of pointless access_ok()
omapfb: get rid of pointless access_ok() calls
amifb: get rid of pointless access_ok() calls
drivers/fpga/dfl-afu-dma-region.c: get rid of pointless access_ok()
drivers/fpga/dfl-fme-pr.c: get rid of pointless access_ok()
cm4000_cs.c cmm_ioctl(): get rid of pointless access_ok()
nvram: drop useless access_ok()
n_hdlc_tty_read(): remove pointless access_ok()
tomoyo_write_control(): get rid of pointless access_ok()
btrfs_ioctl_send(): don't bother with access_ok()
fat_dir_ioctl(): hadn't needed that access_ok() for more than a decade...
dlmfs_file_write(): get rid of pointless access_ok()
set from Mauro toward the completion of the RST conversion. I *really*
hope we are getting close to the end of this. Meanwhile, those patches
reach pretty far afield to update document references around the tree;
there should be no actual code changes there. There will be, alas, more of
the usual trivial merge conflicts.
Beyond that we have more translations, improvements to the sphinx
scripting, a number of additions to the sysctl documentation, and lots of
fixes.
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEIw+MvkEiF49krdp9F0NaE2wMflgFAl7VId8PHGNvcmJldEBs
d24ubmV0AAoJEBdDWhNsDH5Yq/gH/iaDgirQZV6UZ2v9sfwQNYolNpf2sKAuOZjd
bPFB7WJoMQbKwQEvYrAUL2+5zPOcLYuIfzyOfo1BV1py+EyKbACcKjI4AedxfJF7
+NchmOBhlEqmEhzx2U08HRc4/8J223WG17fJRVsV3p+opJySexSFeQucfOciX5NR
RUCxweWWyg/FgyqjkyMMTtsePqZPmcT5dWTlVXISlbWzcv5NFhuJXnSrw8Sfzcmm
SJMzqItv3O+CabnKQ8kMLV2PozXTMfjeWH47ZUK0Y8/8PP9+cvqwFzZ0UDQJ1Xaz
oyW/TqmunaXhfMsMFeFGSwtfgwRHvXdxkQdtwNHvo1dV4dzTvDw=
=fDC/
-----END PGP SIGNATURE-----
Merge tag 'docs-5.8' of git://git.lwn.net/linux
Pull documentation updates from Jonathan Corbet:
"A fair amount of stuff this time around, dominated by yet another
massive set from Mauro toward the completion of the RST conversion. I
*really* hope we are getting close to the end of this. Meanwhile,
those patches reach pretty far afield to update document references
around the tree; there should be no actual code changes there. There
will be, alas, more of the usual trivial merge conflicts.
Beyond that we have more translations, improvements to the sphinx
scripting, a number of additions to the sysctl documentation, and lots
of fixes"
* tag 'docs-5.8' of git://git.lwn.net/linux: (130 commits)
Documentation: fixes to the maintainer-entry-profile template
zswap: docs/vm: Fix typo accept_threshold_percent in zswap.rst
tracing: Fix events.rst section numbering
docs: acpi: fix old http link and improve document format
docs: filesystems: add info about efivars content
Documentation: LSM: Correct the basic LSM description
mailmap: change email for Ricardo Ribalda
docs: sysctl/kernel: document unaligned controls
Documentation: admin-guide: update bug-hunting.rst
docs: sysctl/kernel: document ngroups_max
nvdimm: fixes to maintainter-entry-profile
Documentation/features: Correct RISC-V kprobes support entry
Documentation/features: Refresh the arch support status files
Revert "docs: sysctl/kernel: document ngroups_max"
docs: move locking-specific documents to locking/
docs: move digsig docs to the security book
docs: move the kref doc into the core-api book
docs: add IRQ documentation at the core-api book
docs: debugging-via-ohci1394.txt: add it to the core-api book
docs: fix references for ipmi.rst file
...
Pull crypto updates from Herbert Xu:
"API:
- Introduce crypto_shash_tfm_digest() and use it wherever possible.
- Fix use-after-free and race in crypto_spawn_alg.
- Add support for parallel and batch requests to crypto_engine.
Algorithms:
- Update jitter RNG for SP800-90B compliance.
- Always use jitter RNG as seed in drbg.
Drivers:
- Add Arm CryptoCell driver cctrng.
- Add support for SEV-ES to the PSP driver in ccp"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (114 commits)
crypto: hisilicon - fix driver compatibility issue with different versions of devices
crypto: engine - do not requeue in case of fatal error
crypto: cavium/nitrox - Fix a typo in a comment
crypto: hisilicon/qm - change debugfs file name from qm_regs to regs
crypto: hisilicon/qm - add DebugFS for xQC and xQE dump
crypto: hisilicon/zip - add debugfs for Hisilicon ZIP
crypto: hisilicon/hpre - add debugfs for Hisilicon HPRE
crypto: hisilicon/sec2 - add debugfs for Hisilicon SEC
crypto: hisilicon/qm - add debugfs to the QM state machine
crypto: hisilicon/qm - add debugfs for QM
crypto: stm32/crc32 - protect from concurrent accesses
crypto: stm32/crc32 - don't sleep in runtime pm
crypto: stm32/crc32 - fix multi-instance
crypto: stm32/crc32 - fix run-time self test issue.
crypto: stm32/crc32 - fix ext4 chksum BUG_ON()
crypto: hisilicon/zip - Use temporary sqe when doing work
crypto: hisilicon - add device error report through abnormal irq
crypto: hisilicon - remove codes of directly report device errors through MSI
crypto: hisilicon - QM memory management optimization
crypto: hisilicon - unify initial value assignment into QM
...
we are using copy_to_user()/memdup_user() anyway
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The latest Xilinx design tools called ISE and EDK has been released in
October 2013. New tool doesn't support any PPC405/PPC440 new designs.
These platforms are no longer supported and tested.
PowerPC 405/440 port is orphan from 2013 by
commit cdeb89943b ("MAINTAINERS: Fix incorrect status tag") and
commit 19624236cc ("MAINTAINERS: Update Grant's email address and maintainership")
that's why it is time to remove the support fot these platforms.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/8c593895e2cb57d232d85ce4d8c3a1aa7f0869cc.1590079968.git.christophe.leroy@csgroup.eu
Platform devices can only come in through the DMI interface, and that
will get done before initialization is complete. Therefore there is no
reason to hande getting a device in new_ssif_client after
initialization.
Dynamic entries can still come in through the i2c interfaces, but that's
handled differently.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Close the hole of holding a mapping over kernel driver takeover event of
a given address range.
Commit 90a545e981 ("restrict /dev/mem to idle io memory ranges")
introduced CONFIG_IO_STRICT_DEVMEM with the goal of protecting the
kernel against scenarios where a /dev/mem user tramples memory that a
kernel driver owns. However, this protection only prevents *new* read(),
write() and mmap() requests. Established mappings prior to the driver
calling request_mem_region() are left alone.
Especially with persistent memory, and the core kernel metadata that is
stored there, there are plentiful scenarios for a /dev/mem user to
violate the expectations of the driver and cause amplified damage.
Teach request_mem_region() to find and shoot down active /dev/mem
mappings that it believes it has successfully claimed for the exclusive
use of the driver. Effectively a driver call to request_mem_region()
becomes a hole-punch on the /dev/mem device.
The typical usage of unmap_mapping_range() is part of
truncate_pagecache() to punch a hole in a file, but in this case the
implementation is only doing the "first half" of a hole punch. Namely it
is just evacuating current established mappings of the "hole", and it
relies on the fact that /dev/mem establishes mappings in terms of
absolute physical address offsets. Once existing mmap users are
invalidated they can attempt to re-establish the mapping, or attempt to
continue issuing read(2) / write(2) to the invalidated extent, but they
will then be subject to the CONFIG_IO_STRICT_DEVMEM checking that can
block those subsequent accesses.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes: 90a545e981 ("restrict /dev/mem to idle io memory ranges")
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/159009507306.847224.8502634072429766747.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The MSCC bug fix in 'net' had to be slightly adjusted because the
register accesses are done slightly differently in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
sizeof(flexible-array-member) triggers a warning because flexible array
members have incomplete type[1]. There are some instances of code in
which the sizeof operator is being incorrectly/erroneously applied to
zero-length arrays and the result is zero. Such instances may be hiding
some bugs. So, this work (flexible-array member conversions) will also
help to get completely rid of those sorts of issues.
Also, the following issue shows up due to the flexible-array member
having incomplete type[4]:
drivers/char/tpm/eventlog/tpm2.c: In function ‘tpm2_bios_measurements_start’:
drivers/char/tpm/eventlog/tpm2.c:54:46: error: invalid application of ‘sizeof’ to incomplete type ‘u8[]’ {aka ‘unsigned char[]’}
54 | size = sizeof(struct tcg_pcr_event) - sizeof(event_header->event)
| ^
drivers/char/tpm/eventlog/tpm2.c: In function ‘tpm2_bios_measurements_next’:
drivers/char/tpm/eventlog/tpm2.c:102:10: error: invalid application of ‘sizeof’ to incomplete type ‘u8[]’ {aka ‘unsigned char[]’}
102 | sizeof(event_header->event) + event_header->event_size;
| ^
drivers/char/tpm/eventlog/tpm2.c: In function ‘tpm2_binary_bios_measurements_show’:
drivers/char/tpm/eventlog/tpm2.c:140:10: error: invalid application of ‘sizeof’ to incomplete type ‘u8[]’ {aka ‘unsigned char[]’}
140 | sizeof(event_header->event) + event_header->event_size;
| ^
scripts/Makefile.build:266: recipe for target 'drivers/char/tpm/eventlog/tpm2.o' failed
make[3]: *** [drivers/char/tpm/eventlog/tpm2.o] Error 1
As mentioned above: "Flexible array members have incomplete type, and
so the sizeof operator may not be applied. As a quirk of the original
implementation of zero-length arrays, sizeof evaluates to zero."[1] As
in "sizeof(event_header->event) always evaluated to 0, so removing it
has no effect".
Lastly, make use of the struct_size() helper to deal with the
flexible array member and its host structure.
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
[4] https://github.com/KSPP/linux/issues/43
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
There is export_uuid() function which exports uuid_t to the u8 array.
Use it instead of open coding variant.
This allows to hide the uuid_t internals.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
And replace the arcane return value convention with a simple bool
where true means success and false means failure.
[AV: braino fix folded in]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Try to load acpi_ipmi when an ACPI IPMI interface is added, so that the
ACPI IPMI OpRegion is accessible.
Signed-off-by: Stuart Hayes <stuart.w.hayes@gmail.com>
Message-Id: <20200311192409.59923-1-stuart.w.hayes@gmail.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
If the function platform_get_irq() failed, the negative value
returned will not be detected here. So fix error handling in
bt_bmc_config_irq(). And in the function bt_bmc_probe(),
when get irq failed, it will print error message. So use
platform_get_irq_optional() to simplify code. Finally in the
function bt_bmc_remove() should make the right status check
if get irq failed.
Signed-off-by: Shengju Zhang <zhangshengju@cmss.chinamobile.com>
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Message-Id: <20200505102906.17196-1-tangbin@cmss.chinamobile.com>
[Also set bt_bmc->irq to a negative value if devm_request_irq() fails.]
Signed-off-by: Corey Minyard <cminyard@mvista.com>
There is a specific API to treat raw data as GUID, i.e. import_guid().
Use it instead of guid_copy() with explicit casting.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Message-Id: <20200422130348.38749-1-andriy.shevchenko@linux.intel.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
We met mulitple times of failure of staring bmc-watchdog,
due to the runtime memory allocation failure of order 4.
bmc-watchdog: page allocation failure: order:4, mode:0x40cc0(GFP_KERNEL|__GFP_COMP), nodemask=(null),cpuset=/,mems_allowed=0-1
CPU: 1 PID: 2571 Comm: bmc-watchdog Not tainted 5.5.0-00045-g7d6bb61d6188c #1
Hardware name: Intel Corporation S2600WFT/S2600WFT, BIOS SE5C620.86B.00.01.0015.110720180833 11/07/2018
Call Trace:
dump_stack+0x66/0x8b
warn_alloc+0xfe/0x160
__alloc_pages_slowpath+0xd3e/0xd80
__alloc_pages_nodemask+0x2f0/0x340
kmalloc_order+0x18/0x70
kmalloc_order_trace+0x1d/0xb0
ipmi_create_user+0x55/0x2c0 [ipmi_msghandler]
ipmi_open+0x72/0x110 [ipmi_devintf]
chrdev_open+0xcb/0x1e0
do_dentry_open+0x1ce/0x380
path_openat+0x305/0x14f0
do_filp_open+0x9b/0x110
do_sys_open+0x1bd/0x250
do_syscall_64+0x5b/0x1f0
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Using vzalloc/vfree for creating ipmi_user heals the
problem
Thanks to Stephen Rothwell for finding the vmalloc.h
inclusion issue.
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Fix some format issue of the code in bt-bmc.c
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Signed-off-by: Shengju Zhang <zhangshengju@cmss.chinamobile.com>
Message-Id: <20200414141814.19048-1-tangbin@cmss.chinamobile.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
bt_bmc_probe() is only called with an openfirmware platform device.
Therefore there is no need to check that the passed in device is NULL or
that it has an openfirmware node.
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Message-Id: <20200408115958.2848-1-tangbin@cmss.chinamobile.com>
[Fixed the title up a bit.]
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Wolfram Sang has asked to have this included in 5.7 so the deprecated
API can be removed next release. There should be no functional
difference.
I think that entire this section of code can be removed; it is leftover
from other things that have since changed, but this is the safer thing
to do for now. The full removal can happen next release.
Thanks,
-corey
-----BEGIN PGP SIGNATURE-----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=JH+B
-----END PGP SIGNATURE-----
Merge tag 'for-linus-5.7-2' of git://github.com/cminyard/linux-ipmi
Pull IPMI update from Corey Minyard:
"Convert i2c_new_device() to i2c_new_client_device()
Wolfram Sang has asked to have this included in 5.7 so the deprecated
API can be removed next release. There should be no functional
difference.
I think that entire this section of code can be removed; it is
leftover from other things that have since changed, but this is the
safer thing to do for now. The full removal can happen next release"
* tag 'for-linus-5.7-2' of git://github.com/cminyard/linux-ipmi:
char: ipmi: convert to use i2c_new_client_device()
<linux/cryptohash.h> sounds very generic and important, like it's the
header to include if you're doing cryptographic hashing in the kernel.
But actually it only includes the library implementation of the SHA-1
compression function (not even the full SHA-1). This should basically
never be used anymore; SHA-1 is no longer considered secure, and there
are much better ways to do cryptographic hashing in the kernel.
Remove this header and fold it into <crypto/sha.h> which already
contains constants and functions for SHA-1 (along with SHA-2).
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The library implementation of the SHA-1 compression function is
confusingly called just "sha_transform()". Alongside it are some "SHA_"
constants and "sha_init()". Presumably these are left over from a time
when SHA just meant SHA-1. But now there are also SHA-2 and SHA-3, and
moreover SHA-1 is now considered insecure and thus shouldn't be used.
Therefore, rename these functions and constants to make it very clear
that they are for SHA-1. Also add a comment to make it clear that these
shouldn't be used.
For the extra-misleadingly named "SHA_MESSAGE_BYTES", rename it to
SHA1_BLOCK_SIZE and define it to just '64' rather than '(512/8)' so that
it matches the same definition in <crypto/sha.h>. This prepares for
merging <linux/cryptohash.h> into <crypto/sha.h>.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
For many users, the Arm CryptoCell HW is not available, so the default for
HW_RANDOM_CCTRNG should to n.
Remove the line to follow the convention - 'n' is the default anyway so no
need to state it explicitly.
Signed-off-by: Hadar Gat <hadar.gat@arm.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The cctrng is unusable on non-DT systems so we should depend
on it.
Signed-off-by: Hadar Gat <hadar.gat@arm.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Fix the following sparse warnings:
drivers/char/hw_random/cctrng.c:316:6: warning: symbol
'cc_trng_compwork_handler' was not declared. Should it be static?
drivers/char/hw_random/cctrng.c:451:6: warning: symbol
'cc_trng_startwork_handler' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Acked-by: Hadar Gat <hadar.gat@arm.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
There is export_uuid() function which exports uuid_t to the u8 array.
Use it instead of open coding variant.
This allows to hide the uuid_t internals.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch removes the unnecessary FIPS ifdef in cctrng.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Hadar Gat <hadar.gat@arm.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
