The reset-simple driver can be used without changes.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Add reset line status readback, inverted status support, and socfpga
device tree quirks to the simple reset driver, and use it to replace
the socfpga driver.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Use the newly created copies in the reset-simple driver to replace the
sunxi platform driver code and reset operations. The separate sunxi
driver still remains to register the early reset controllers, but it
reuses the reset operations in reset-simple.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Copy reusable parts from the sunxi driver, to add a driver for simple
reset controllers with reset lines that can be controlled by toggling
bits in exclusive, contiguous register ranges using read-modify-write
cycles under a spinlock.
The following patches will replace compatible reset drivers with
reset-simple, extending it where necessary.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
The if (bank >= REG_COUNT) is not need since already checked
by the default rcdev->of_xlate implementation which guarantees that
id < rcdev->nr_resets.
Suggested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The Amlogic GX SoC family embeds alternate registers to drive the reset
levels next to the pulse registers.
This patch adds support for level reset handling on the GX family only.
The Meson8 family has an alternate way to handle level reset.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Add basic reset data for Socionext's new SoC PXs3.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Enable the reset driver to get built for the Stratix10 platform.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The SoCFPGA Stratix10 reset controller has 32-bit registers. Thus, we
cannot use BITS_PER_LONG in computing the register and bit offset. Instead,
we should be using the width of the hardware register for the calculation.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The HSDK reset driver is only useful when building for an ARC HSDK
platform.
While at it, drop the "default n", as that is the default.
Fixes: e0be864f14 ("ARC: reset: introduce HSDKv1 reset driver")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
[p.zabel@pengutronix.de: rebased, renamed RESET_HSDK_V1 to RESET_HSDK]
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
ARC AXS10x boards support custom IP-block which allows to control
reset signals of selected peripherals. For example DW GMAC, etc...
This block is controlled via memory-mapped register (AKA CREG) which
represents up-to 32 reset lines. This regiter is self-clearing so we
don't need to deassert line after reset.
As of today only the following lines are used:
- DW GMAC - line 5
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
There is no plan yet to do a v2 board. And even if we were to do it only
some IPs would actually change, so it be best to add suffixes at that
point, not now !
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
This avoids the error:
drivers/reset/reset-hsdk-v1.o: In function `hsdkv1_reset_probe':
/home/thomas/git/linux/drivers/reset/reset-hsdk-v1.c:101: undefined
reference to `devm_ioremap_resource'
collect2: error: ld returned 1 exit status
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for 4.14 for MIPS; below a summary of
the non-merge commits:
CM:
- Rename mips_cm_base to mips_gcr_base
- Specify register size when generating accessors
- Use BIT/GENMASK for register fields, order & drop shifts
- Add cluster & block args to mips_cm_lock_other()
CPC:
- Use common CPS accessor generation macros
- Use BIT/GENMASK for register fields, order & drop shifts
- Introduce register modify (set/clear/change) accessors
- Use change_*, set_* & clear_* where appropriate
- Add CM/CPC 3.5 register definitions
- Use GlobalNumber macros rather than magic numbers
- Have asm/mips-cps.h include CM & CPC headers
- Cluster support for topology functions
- Detect CPUs in secondary clusters
CPS:
- Read GIC_VL_IDENT directly, not via irqchip driver
DMA:
- Consolidate coherent and non-coherent dma_alloc code
- Don't use dma_cache_sync to implement fd_cacheflush
FPU emulation / FP assist code:
- Another series of 14 commits fixing corner cases such as NaN
propgagation and other special input values.
- Zero bits 32-63 of the result for a CLASS.D instruction.
- Enhanced statics via debugfs
- Do not use bools for arithmetic. GCC 7.1 moans about this.
- Correct user fault_addr type
Generic MIPS:
- Enhancement of stack backtraces
- Cleanup from non-existing options
- Handle non word sized instructions when examining frame
- Fix detection and decoding of ADDIUSP instruction
- Fix decoding of SWSP16 instruction
- Refactor handling of stack pointer in get_frame_info
- Remove unreachable code from force_fcr31_sig()
- Convert to using %pOF instead of full_name
- Remove the R6000 support.
- Move FP code from *_switch.S to *_fpu.S
- Remove unused ST_OFF from r2300_switch.S
- Allow platform to specify multiple its.S files
- Add #includes to various files to ensure code builds reliable and
without warning..
- Remove __invalidate_kernel_vmap_range
- Remove plat_timer_setup
- Declare various variables & functions static
- Abstract CPU core & VP(E) ID access through accessor functions
- Store core & VP IDs in GlobalNumber-style variable
- Unify checks for sibling CPUs
- Add CPU cluster number accessors
- Prevent direct use of generic_defconfig
- Make CONFIG_MIPS_MT_SMP default y
- Add __ioread64_copy
- Remove unnecessary inclusions of linux/irqchip/mips-gic.h
GIC:
- Introduce asm/mips-gic.h with accessor functions
- Use new GIC accessor functions in mips-gic-timer
- Remove counter access functions from irq-mips-gic.c
- Remove gic_read_local_vp_id() from irq-mips-gic.c
- Simplify shared interrupt pending/mask reads in irq-mips-gic.c
- Simplify gic_local_irq_domain_map() in irq-mips-gic.c
- Drop gic_(re)set_mask() functions in irq-mips-gic.c
- Remove gic_set_polarity(), gic_set_trigger(), gic_set_dual_edge(),
gic_map_to_pin() and gic_map_to_vpe() from irq-mips-gic.c.
- Convert remaining shared reg access, local int mask access and
remaining local reg access to new accessors
- Move GIC_LOCAL_INT_* to asm/mips-gic.h
- Remove GIC_CPU_INT* macros from irq-mips-gic.c
- Move various definitions to the driver
- Remove gic_get_usm_range()
- Remove __gic_irq_dispatch() forward declaration
- Remove gic_init()
- Use mips_gic_present() in place of gic_present and remove
gic_present
- Move gic_get_c0_*_int() to asm/mips-gic.h
- Remove linux/irqchip/mips-gic.h
- Inline __gic_init()
- Inline gic_basic_init()
- Make pcpu_masks a per-cpu variable
- Use pcpu_masks to avoid reading GIC_SH_MASK*
- Clean up mti, reserved-cpu-vectors handling
- Use cpumask_first_and() in gic_set_affinity()
- Let the core set struct irq_common_data affinity
microMIPS:
- Fix microMIPS stack unwinding on big endian systems
MIPS-GIC:
- SYNC after enabling GIC region
NUMA:
- Remove the unused parent_node() macro
R6:
- Constify r2_decoder_tables
- Add accessor & bit definitions for GlobalNumber
SMP:
- Constify smp ops
- Allow boot_secondary SMP op to return errors
VDSO:
- Drop gic_get_usm_range() usage
- Avoid use of linux/irqchip/mips-gic.h
Platform changes:
Alchemy:
- Add devboard machine type to cpuinfo
- update cpu feature overrides
- Threaded carddetect irqs for devboards
AR7:
- allow NULL clock for clk_get_rate
BCM63xx:
- Fix ENETDMA_6345_MAXBURST_REG offset
- Allow NULL clock for clk_get_rate
CI20:
- Enable GPIO and RTC drivers in defconfig
- Add ethernet and fixed-regulator nodes to DTS
Generic platform:
- Move Boston and NI 169445 FIT image source to their own files
- Include asm/bootinfo.h for plat_fdt_relocated()
- Include asm/time.h for get_c0_*_int()
- Include asm/bootinfo.h for plat_fdt_relocated()
- Include asm/time.h for get_c0_*_int()
- Allow filtering enabled boards by requirements
- Don't explicitly disable CONFIG_USB_SUPPORT
- Bump default NR_CPUS to 16
JZ4700:
- Probe the jz4740-rtc driver from devicetree
Lantiq:
- Drop check of boot select from the spi-falcon driver.
- Drop check of boot select from the lantiq-flash MTD driver.
- Access boot cause register in the watchdog driver through regmap
- Add device tree binding documentation for the watchdog driver
- Add docs for the RCU DT bindings.
- Convert the fpi bus driver to a platform_driver
- Remove ltq_reset_cause() and ltq_boot_select(
- Switch to a proper reset driver
- Switch to a new drivers/soc GPHY driver
- Add an USB PHY driver for the Lantiq SoCs using the RCU module
- Use of_platform_default_populate instead of __dt_register_buses
- Enable MFD_SYSCON to be able to use it for the RCU MFD
- Replace ltq_boot_select() with dummy implementation.
Loongson 2F:
- Allow NULL clock for clk_get_rate
Malta:
- Use new GIC accessor functions
NI 169445:
- Add support for NI 169445 board.
- Only include in 32r2el kernels
Octeon:
- Add support for watchdog of 78XX SOCs.
- Add support for watchdog of CN68XX SOCs.
- Expose support for mips32r1, mips32r2 and mips64r1
- Enable more drivers in config file
- Add support for accessing the boot vector.
- Remove old boot vector code from watchdog driver
- Define watchdog registers for 70xx, 73xx, 78xx, F75xx.
- Make CSR functions node aware.
- Allow access to CIU3 IRQ domains.
- Misc cleanups in the watchdog driver
Omega2+:
- New board, add support and defconfig
Pistachio:
- Enable Root FS on NFS in defconfig
Ralink:
- Add Mediatek MT7628A SoC
- Allow NULL clock for clk_get_rate
- Explicitly request exclusive reset control in the pci-mt7620 PCI driver.
SEAD3:
- Only include in 32 bit kernels by default
VoCore:
- Add VoCore as a vendor t0 dt-bindings
- Add defconfig file"
* '4.14-features' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (167 commits)
MIPS: Refactor handling of stack pointer in get_frame_info
MIPS: Stacktrace: Fix microMIPS stack unwinding on big endian systems
MIPS: microMIPS: Fix decoding of swsp16 instruction
MIPS: microMIPS: Fix decoding of addiusp instruction
MIPS: microMIPS: Fix detection of addiusp instruction
MIPS: Handle non word sized instructions when examining frame
MIPS: ralink: allow NULL clock for clk_get_rate
MIPS: Loongson 2F: allow NULL clock for clk_get_rate
MIPS: BCM63XX: allow NULL clock for clk_get_rate
MIPS: AR7: allow NULL clock for clk_get_rate
MIPS: BCM63XX: fix ENETDMA_6345_MAXBURST_REG offset
mips: Save all registers when saving the frame
MIPS: Add DWARF unwinding to assembly
MIPS: Make SAVE_SOME more standard
MIPS: Fix issues in backtraces
MIPS: jz4780: DTS: Probe the jz4740-rtc driver from devicetree
MIPS: Ci20: Enable RTC driver
watchdog: octeon-wdt: Add support for 78XX SOCs.
watchdog: octeon-wdt: Add support for cn68XX SOCs.
watchdog: octeon-wdt: File cleaning.
...
This branch contains platform-related driver updates for ARM and ARM64.
Among them:
- Reset driver updates:
+ New API for dealing with arrays of resets
+ Make unimplemented {de,}assert return success on shared resets
+ MSDKv1 driver
+ Removal of obsolete Gemini reset driver
+ Misc updates for sunxi and Uniphier
- SoC drivers:
+ Platform SoC driver registration on Tegra
+ Shuffle of Qualcomm drivers into a submenu
+ Allwinner A64 support for SRAM
+ Renesas R-Car R3 support
+ Power domains for Rockchip RK3366
- Misc updates and smaller fixes for TEE and memory driver subsystems
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=yBzS
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"This branch contains platform-related driver updates for ARM and ARM64.
Among them:
- Reset driver updates:
+ New API for dealing with arrays of resets
+ Make unimplemented {de,}assert return success on shared resets
+ MSDKv1 driver
+ Removal of obsolete Gemini reset driver
+ Misc updates for sunxi and Uniphier
- SoC drivers:
+ Platform SoC driver registration on Tegra
+ Shuffle of Qualcomm drivers into a submenu
+ Allwinner A64 support for SRAM
+ Renesas R-Car R3 support
+ Power domains for Rockchip RK3366
- Misc updates and smaller fixes for TEE and memory driver
subsystems"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (54 commits)
firmware: arm_scpi: fix endianness of dev_id in struct dev_pstate_set
soc/tegra: fuse: Add missing semi-colon
soc/tegra: Restrict SoC device registration to Tegra
drivers: soc: sunxi: add support for A64 and its SRAM C
drivers: soc: sunxi: add support for remapping func value to reg value
drivers: soc: sunxi: fix error processing on base address when claiming
dt-bindings: add binding for Allwinner A64 SRAM controller and SRAM C
bus: sunxi-rsb: Enable by default for ARM64
soc/tegra: Register SoC device
firmware: tegra: set drvdata earlier
memory: Convert to using %pOF instead of full_name
soc: Convert to using %pOF instead of full_name
bus: Convert to using %pOF instead of full_name
firmware: Convert to using %pOF instead of full_name
soc: mediatek: add SCPSYS power domain driver for MediaTek MT7622 SoC
soc: mediatek: add header files required for MT7622 SCPSYS dt-binding
soc: mediatek: reduce code duplication of scpsys_probe across all SoCs
dt-bindings: soc: update the binding document for SCPSYS on MediaTek MT7622 SoC
reset: uniphier: add analog amplifiers reset control
reset: uniphier: add video input subsystem reset control
...
The reset controllers (on xRX200 and newer SoCs have two of them) are
provided by the RCU module. This was initially implemented as a simple
reset controller. However, the RCU module provides more functionality
(ethernet GPHYs, USB PHY, etc.), which makes it a MFD device.
The old reset controller driver implementation from
arch/mips/lantiq/xway/reset.c did not honor this fact.
For some devices the request and the status bits are different.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Cc: john@phrozen.org
Cc: kishon@ti.com
Cc: mark.rutland@arm.com
Cc: linux-mips@linux-mips.org
Cc: linux-mtd@lists.infradead.org
Cc: linux-watchdog@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: linux-spi@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/17125/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add a reset line for analog signal amplifier core (ADAMV) on
UniPhier LD11/LD20 SoCs.
Signed-off-by: Katsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Add a reset line for video input subsystem (EXIV) on
UniPhier LD11/LD20 SoCs.
Signed-off-by: Katsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The Allwinner reset controller has 32-bit registers, but resource_size
is measured in bytes, not number of registers.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Chen-Yu Tsai <wens@csie.org>
This macro turned out not so useful as I had expected.
Hardware engineers said they would change reset bit assignments for
every SoC going forward. This means we can not share the macros
among SoCs. Just use primitive macros.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
This SoC is too old. It is difficult to maintain any longer.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
This reverts commit 2acb037fc4.
We ended up merging the reset controller into the clock
controller so we can now get rid of this stand-alone
implementation.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The HSDK v1 periphery IPs can be reset by accessing some registers
from the CGU block.
The list of available reset lines is documented in the DT bindings.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Now that we have a custom printf format specifier, convert users of
full_name to use %pOF instead. This is preparation to remove storing
of the full path string for each node.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
By now there are drivers using shared reset controls and (de)assert
calls on platforms with self-deasserting reset lines and thus reset
drivers that do not implement .assert() and .deassert().
As long as the initial state of the reset line is deasserted, there
is no reason for a reset_control_assert call to return an error for
shared reset controls, or for a reset_control_deassert call to return
an error for either shared or exclusive reset controls: after a call
to reset_control_deassert the reset line is guaranteed to be deasserted,
and after a call to reset_control_assert it is valid for the reset
line to stay deasserted for shared reset controls.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Many devices may want to request a bunch of resets and control them. So
it's better to manage them as an array. Add APIs to _get() an array of
reset_control, reusing the _assert(), _deassert(), and _reset() APIs for
single reset controls. Since reset controls already may control multiple
reset lines with a single hardware bit, from the user perspective, reset
control arrays are not at all different from single reset controls.
Note that these APIs don't guarantee that the reset lines managed in the
array are handled in any particular order.
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
[p.zabel@pengutronix.de: changed API to hide reset control arrays behind
struct reset_control]
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
- New SoC specific drivers
- NVIDIA Tegra PM Domain support for newer SoCs (Tegra186 and later)
based on the "BPMP" firmware
- Clocksource and system controller drivers for the newly added
Action Semi platforms (both arm and arm64).
- Reset subsystem, merged through arm-soc by tradition:
- New drivers for Altera Stratix10, TI Keystone and Cortina Gemini SoCs
- Various subsystem-wide cleanups
- Updates for existing SoC-specific drivers
- TI GPMC (General Purpose Memory Controller)
- Mediatek "scpsys" system controller support for MT6797
- Broadcom "brcmstb_gisb" bus arbitrer
- ARM SCPI firmware
- Renesas "SYSC" system controller
One more driver update was submitted for the Freescale/NXP DPAA
data path acceleration that has previously been used on PowerPC
chips. I ended up postponing the merge until some API questions
for its unusual MMIO access are resolved.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=5L6n
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"New SoC specific drivers:
- NVIDIA Tegra PM Domain support for newer SoCs (Tegra186 and later)
based on the "BPMP" firmware
- Clocksource and system controller drivers for the newly added
Action Semi platforms (both arm and arm64).
Reset subsystem, merged through arm-soc by tradition:
- New drivers for Altera Stratix10, TI Keystone and Cortina Gemini
SoCs
- Various subsystem-wide cleanups
Updates for existing SoC-specific drivers
- TI GPMC (General Purpose Memory Controller)
- Mediatek "scpsys" system controller support for MT6797
- Broadcom "brcmstb_gisb" bus arbitrer
- ARM SCPI firmware
- Renesas "SYSC" system controller
One more driver update was submitted for the Freescale/NXP DPAA data
path acceleration that has previously been used on PowerPC chips. I
ended up postponing the merge until some API questions for its unusual
MMIO access are resolved"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (35 commits)
clocksource: owl: Add S900 support
clocksource: Add Owl timer
soc: renesas: rcar-sysc: Use GENPD_FLAG_ALWAYS_ON
firmware: tegra: Fix locking bugs in BPMP
soc/tegra: flowctrl: Fix error handling
soc/tegra: bpmp: Implement generic PM domains
soc/tegra: bpmp: Update ABI header
PM / Domains: Allow overriding the ->xlate() callback
soc: brcmstb: enable drivers for ARM64 and BMIPS
soc: renesas: Rework Kconfig and Makefile logic
reset: Add the TI SCI reset driver
dt-bindings: reset: Add TI SCI reset binding
reset: use kref for reference counting
soc: qcom: smsm: Improve error handling, quiesce probe deferral
cpufreq: scpi: use new scpi_ops functions to remove duplicate code
firmware: arm_scpi: add support to populate OPPs and get transition latency
dt-bindings: reset: Add reset manager offsets for Stratix10
memory: omap-gpmc: add error message if bank-width property is absent
memory: omap-gpmc: make dts snippet include semicolon
reset: Add a Gemini reset controller
...
Some TI Keystone family of SoCs contain a system controller (like the
Power Management Micro Controller (PMMC) on 66AK2G SoCs) that manage
the low-level device control (like clocks, resets etc) for the various
hardware modules present on the SoC. These device control operations
are provided to the host processor OS through a communication protocol
called the TI System Control Interface (TI SCI) protocol.
This patch adds a reset driver that communicates to the system
controller over the TI SCI protocol for performing reset management
of various devices present on the SoC. Various reset functionalities
are achieved by the means of different TI SCI device operations
provided by the TI SCI framework.
Signed-off-by: Andrew F. Davis <afd@ti.com>
[s-anna@ti.com: documentation changes, revised commit message]
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
[p.zabel@pengutronix.de: const struct reset_control_ops]
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The hi6220_reset driver can be built as a standalone module
yet it cannot be loaded because it depends on GPL exported symbols.
Lets set the module license so that the module loads, and things like
the on-board kirin drm starts working.
Signed-off-by: Jeremy Linton <lintonrjeremy@gmail.com>
Reviewed-by: Xinliang Liu <xinliang.liu@linaro.org>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The Cortina Systems Gemini reset controller is a simple
32bit register with self-deasserting reset lines. It is
accessed using regmap over syscon.
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Rename the current Kconfig name used for the TI SYSCON Reset
driver from TI_SYSCON_RESET to RESET_TI_SYSCON to match the
convention used for all the reset drivers present at the
base reset folder.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
* A multiplication for the size determination of a memory allocation
indicated that an array data structure should be processed.
Thus use the corresponding function "devm_kcalloc".
* Replace the specification of a data structure by a pointer dereference
to make the corresponding size determination a bit safer according to
the Linux coding style convention.
* Delete the local variable "size" which became unnecessary with
this refactoring.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Driver updates for ARM SoCs.
* Reset subsystem, merged through arm-soc by tradition:
- Make bool drivers explicitly non-modular
- New support for i.MX7 and Arria10 reset controllers
* PATA driver for Palmchip BK371 (acked by Tejun)
* Power domain drivers for i.MX (GPC, GPCv2)
- Moved out of mach-imx for GPC
- Bunch of tweaks, fixes, etc
* PMC support for Tegra186
* SoC detection support for Renesas RZ/G1H and RZ/G1N
* Move Tegra flow controller driver from mach directory to drivers/soc
- (Power management / CPU power driver)
* Misc smaller tweaks for other platforms
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=B43K
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"Driver updates for ARM SoCs:
Reset subsystem, merged through arm-soc by tradition:
- Make bool drivers explicitly non-modular
- New support for i.MX7 and Arria10 reset controllers
PATA driver for Palmchip BK371 (acked by Tejun)
Power domain drivers for i.MX (GPC, GPCv2)
- Moved out of mach-imx for GPC
- Bunch of tweaks, fixes, etc
PMC support for Tegra186
SoC detection support for Renesas RZ/G1H and RZ/G1N
Move Tegra flow controller driver from mach directory to drivers/soc
- (Power management / CPU power driver)
Misc smaller tweaks for other platforms"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (60 commits)
soc: pm-domain: Fix the mangled urls
soc: renesas: rcar-sysc: Add support for R-Car H3 ES2.0
soc: renesas: rcar-sysc: Add support for fixing up power area tables
soc: renesas: Register SoC device early
soc: imx: gpc: add workaround for i.MX6QP to the GPC PD driver
dt-bindings: imx-gpc: add i.MX6 QuadPlus compatible
soc: imx: gpc: add defines for domain index
soc: imx: Add GPCv2 power gating driver
dt-bindings: Add GPCv2 power gating driver
ARM/clk: move the ICST library to drivers/clk
ARM: plat-versatile: remove stale clock header
ARM: keystone: Drop PM domain support for k2g
soc: ti: Add ti_sci_pm_domains driver
dt-bindings: Add TI SCI PM Domains
PM / Domains: Do not check if simple providers have phandle cells
PM / Domains: Add generic data pointer to genpd data struct
soc/tegra: Add initial flowctrl support for Tegra132/210
soc/tegra: flowctrl: Add basic platform driver
soc/tegra: Move Tegra flowctrl driver
ARM: tegra: Remove unnecessary inclusion of flowctrl header
...
Rename the internal __reset_control_get/put functions to
__reset_control_get/put_internal and add an exported
__reset_control_get equivalent to __of_reset_control_get
that takes a struct device parameter.
This avoids the confusing call to __of_reset_control_get in
the non-DT case and fixes the devm_reset_control_get_optional
function to return NULL if RESET_CONTROLLER is enabled but
dev->of_node == NULL.
Fixes: bb475230b8 ("reset: make optional functions really optional")
Reported-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Ramiro Oliveira <Ramiro.Oliveira@synopsys.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Add reset lines for the Denali NAND controller on all UniPhier SoCs,
for the Cadence eMMC controller on LD11/LD20 SoCs.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The Allwinner reset controller has 32-bit registers, so translating
the reset cell number into a register and bit offset should not use
any architecture dependent data size. Otherwise this breaks for 64-bit
architectures like arm64.
Fix this by making it clear that it's the hardware register width which
matters here in the calculation.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
This patch adds the reset controller functionality for
Peripheral PHYs to the Arria10 System Resource Chip.
Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The SoC-FPGA reset controller driver defines NR_BANKS as 4 and uses that define
for two unrelated purposes. It is used
1. as an increment for reset line banks which are 32-bit registers with 4-byte
aligned addresses.
2. as the total number of reset line banks which together with the number of
resets per bank (32) limits the total number of useable resets to 128 and the
highest useable reset ID to 127.
This is clearly wrong as there are resets with higher IDs than 127 defined in
include/dt-bindings/reset/altr,rst-mgr.h and altr,rst-mgr-a10.h.
The patch introduces a new define BANK_INCREMENT for calculating the register
addresses as before and increases NR_BANKS to 8 for useable reset IDs up to 255.
Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Fixes the following sparse warnings:
drivers/reset/reset-uniphier.c:68:34: warning:
symbol 'uniphier_sld3_sys_reset_data' was not declared. Should it be static?
drivers/reset/reset-uniphier.c:73:34: warning:
symbol 'uniphier_pro4_sys_reset_data' was not declared. Should it be static?
drivers/reset/reset-uniphier.c:81:34: warning:
symbol 'uniphier_pro5_sys_reset_data' was not declared. Should it be static?
drivers/reset/reset-uniphier.c:89:34: warning:
symbol 'uniphier_pxs2_sys_reset_data' was not declared. Should it be static?
drivers/reset/reset-uniphier.c:103:34: warning:
symbol 'uniphier_ld11_sys_reset_data' was not declared. Should it be static?
drivers/reset/reset-uniphier.c:108:34: warning:
symbol 'uniphier_ld20_sys_reset_data' was not declared. Should it be static?
drivers/reset/reset-uniphier.c:137:34: warning:
symbol 'uniphier_sld3_mio_reset_data' was not declared. Should it be static?
drivers/reset/reset-uniphier.c:157:34: warning:
symbol 'uniphier_pro5_sd_reset_data' was not declared. Should it be static?
drivers/reset/reset-uniphier.c:174:34: warning:
symbol 'uniphier_ld4_peri_reset_data' was not declared. Should it be static?
drivers/reset/reset-uniphier.c:187:34: warning:
symbol 'uniphier_pro4_peri_reset_data' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The Kconfig currently controlling compilation of this code is:
drivers/reset/Kconfig:config RESET_PISTACHIO
drivers/reset/Kconfig: bool "Pistachio Reset Driver" if COMPILE_TEST
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modular infrastructure use, so that
when reading the driver there is no doubt it is builtin-only.
Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Cc: Damien Horsley <Damien.Horsley@imgtec.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The Kconfig currently controlling compilation of this code is:
drivers/reset/Kconfig:config RESET_ATH79
drivers/reset/Kconfig: bool "AR71xx Reset Driver" if COMPILE_TEST
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
We explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and it allows us to drop the ".remove"
code for non-modular drivers.
Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
Cc: Alban Bedel <albeu@free.fr>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Alban Bedel <albeu@free.fr>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The Kconfig currently controlling compilation of this code is:
drivers/reset/Kconfig:config RESET_OXNAS
drivers/reset/Kconfig: bool
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modular infrastructure use, so that
when reading the driver there is no doubt it is builtin-only.
Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
Cc: linux-oxnas@lists.tuxfamily.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The Kconfig currently controlling compilation of this code is:
arch/arm/mach-meson/Kconfig:menuconfig ARCH_MESON
arch/arm/mach-meson/Kconfig: bool "Amlogic Meson SoCs"
arch/arm64/Kconfig.platforms:config ARCH_MESON
arch/arm64/Kconfig.platforms: bool "Amlogic Platforms"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
Cc: Carlo Caione <carlo@caione.org>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: linux-amlogic@lists.infradead.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Driver updates for ARM SoCs.
A handful of driver changes this time around. The larger changes are:
- Reset drivers for hi3660 and zx2967
- AHCI driver for Davinci, acked by Tejun and brought in here due to
platform dependencies
- Cleanups of atmel-ebi (External Bus Interface)
- Tweaks for Rockchip GRF (General Register File) usage (kitchensink misc
register range on the SoCs)
- PM domains changes for support of two new ZTE SoCs (zx296718 and zx2967)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=od7u
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"Driver updates for ARM SoCs.
A handful of driver changes this time around. The larger changes are:
- Reset drivers for hi3660 and zx2967
- AHCI driver for Davinci, acked by Tejun and brought in here due to
platform dependencies
- Cleanups of atmel-ebi (External Bus Interface)
- Tweaks for Rockchip GRF (General Register File) usage (kitchensink
misc register range on the SoCs)
- PM domains changes for support of two new ZTE SoCs (zx296718 and
zx2967)"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (53 commits)
soc: samsung: pmu: Add register defines for pad retention control
reset: make zx2967 explicitly non-modular
reset: core: fix reset_control_put
soc: samsung: pm_domains: Read domain name from the new label property
soc: samsung: pm_domains: Remove message about failed memory allocation
soc: samsung: pm_domains: Remove unused name field
soc: samsung: pm_domains: Use full names in subdomains registration log
sata: ahci-da850: un-hardcode the MPY bits
sata: ahci-da850: add a workaround for controller instability
sata: ahci: export ahci_do_hardreset() locally
sata: ahci-da850: implement a workaround for the softreset quirk
sata: ahci-da850: add device tree match table
sata: ahci-da850: get the sata clock using a connection id
soc: samsung: pmu: Remove duplicated define for ARM_L2_OPTION register
memory: atmel-ebi: Enable the SMC clock if specified
soc: samsung: pmu: Remove unused and duplicated defines
memory: atmel-ebi: Properly handle multiple reference to the same CS
memory: atmel-ebi: Fix the test to enable generic SMC logic
soc: samsung: pm_domains: Add new Exynos5433 compatible
soc: samsung: pmu: Add dummy support for Exynos5433 SoC
...
For a shared reset, when the reset is successful, the triggered_count is
incremented when trying to call the reset callback, so that another device
sharing the same reset line won't trigger it again. If the reset has not
been triggered successfully, the trigger_count should be decremented.
The code does the opposite, and decrements the trigger_count on success.
As a consequence, another device sharing the reset will be able to trigger
it again.
Fixed be removing negation in from of the error code of the reset function.
Fixes: 7da33a37b4 ("reset: allow using reset_control_reset with shared reset")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The Kconfig currently controlling compilation of this code is:
config RESET_ZX2967
bool "ZTE ZX2967 Reset Driver
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modular infrastructure use, so that
when reading the driver there is no doubt it is builtin-only.
Since builtin_platform_driver() was already in use, the init ordering
remains unchanged with this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
We don't replace module.h with init.h since the file does not appear
to use __init prefix anywhere.
Cc: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Reviewed-by: Baoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Commit "reset: make optional functions really optional" missed to
adjust one check in reset_control_put, causing a NULL pointer
access for optional resets.
Fixes: bb475230b8 "reset: make optional functions really optional"
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The *_get_optional_* functions weren't really optional so this patch
makes them really optional.
These *_get_optional_* functions will now return NULL instead of an error
if no matching reset phandle is found in the DT, and all the
reset_control_* functions now accept NULL rstc pointers.
Signed-off-by: Ramiro Oliveira <Ramiro.Oliveira@synopsys.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Since the new parameter being added is going to be a bool this patch
changes the shared flag from int to bool to match the new parameter.
Signed-off-by: Ramiro Oliveira <Ramiro.Oliveira@synopsys.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The LD11 SoC is equipped with not only MIO-reset but also SD-reset
for controlling RST_n pin of the eMMC device.
Update the binding document and remove unneeded "." from each line
in itemization.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Declare reset_control_ops structures as const as they are only stored
in the ops field of a reset_controller_dev structure. This field is of
type const struct reset_control_ops *, so reset_control_ops structures
having this property can be declared as const.
Done using Coccinelle:
@r1 disable optional_qualifier@
identifier i;
position p;
@@
static struct reset_control_ops i@p={...};
@ok1@
identifier r1.i;
position p;
struct ti_syscon_reset_data data;
@@
data.rcdev.ops=&i@p;
@bad@
position p!={r1.p,ok1.p};
identifier r1.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
+const
struct reset_control_ops i;
File size before: drivers/reset/reset-ti-syscon.o
text data bss dec hex filename
1329 240 0 1569 621 drivers/reset/reset-ti-syscon.o
File size after: drivers/reset/reset-ti-syscon.o
text data bss dec hex filename
1377 192 0 1569 621 drivers/reset/reset-ti-syscon.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
If STATUS_SET was not set, ti_syscon_reset_status would always return 0
no matter whether the status_bit was set or not.
Signed-off-by: Jiancheng Xue <xuejiancheng@hisilicon.com>
Fixes: cc7c2bb149 ("reset: add TI SYSCON based reset driver")
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Driver updates for ARM SoCs, including a couple of newly added drivers:
- A new driver for the power management controller on TI Keystone
- Support for the prerelease "SCPI" firmware protocol that ended up
being shipped by Amlogic in their GXBB SoC.
- A soc_device can now be matched using a glob from inside the
kernel, when another driver wants to know the specific chip
it is running on and cannot find out from DT, firmware or hardware.
- Renesas SoCs now support identification through the soc_device
interface, both in user space and kernel.
- Renesas r8a7743 and r8a7745 gain support for their system controller
- A new checking module for the ARM "PSCI" (not to be confused
with "SCPI" mentioned above) firmware interface.
- A new driver for the Tegra GMI memory interface
- Support for the Tegra firmware interfaces with their
power management controllers
As usual, the updates for the reset controller framework are merged
here, as they tend to touch multiple SoCs as well, including a new
driver for the Oxford (now Broadcom) OX820 chip and the Tegra
bpmp interface.
The existing drivers for Atmel, Qualcomm, NVIDIA, TI Davinci, and
Rockchips SoCs see some further updates.
Conflicts:
- ARCH_RENESAS now selects SOC_BUS, but no longer needs GPIOLIB
- drivers/soc/renesas/Makefile: multiple files got added, keep
all in logical sorting
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=6dP8
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"Driver updates for ARM SoCs, including a couple of newly added
drivers:
- A new driver for the power management controller on TI Keystone
- Support for the prerelease "SCPI" firmware protocol that ended up
being shipped by Amlogic in their GXBB SoC.
- A soc_device can now be matched using a glob from inside the
kernel, when another driver wants to know the specific chip it is
running on and cannot find out from DT, firmware or hardware.
- Renesas SoCs now support identification through the soc_device
interface, both in user space and kernel.
- Renesas r8a7743 and r8a7745 gain support for their system
controller
- A new checking module for the ARM "PSCI" (not to be confused with
"SCPI" mentioned above) firmware interface.
- A new driver for the Tegra GMI memory interface
- Support for the Tegra firmware interfaces with their power
management controllers
As usual, the updates for the reset controller framework are merged
here, as they tend to touch multiple SoCs as well, including a new
driver for the Oxford (now Broadcom) OX820 chip and the Tegra bpmp
interface.
The existing drivers for Atmel, Qualcomm, NVIDIA, TI Davinci, and
Rockchips SoCs see some further updates"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (76 commits)
misc: sram: remove useless #ifdef
drivers: psci: Allow PSCI node to be disabled
drivers: psci: PSCI checker module
soc: renesas: Identify SoC and register with the SoC bus
firmware: qcom: scm: Return PTR_ERR when devm_clk_get fails
firmware: qcom: scm: Remove core, iface and bus clocks dependency
dt-bindings: firmware: scm: Add MSM8996 DT bindings
memory: da8xx-ddrctl: drop the call to of_flat_dt_get_machine_name()
bus: da8xx-mstpri: drop the call to of_flat_dt_get_machine_name()
ARM: shmobile: Document DT bindings for Product Register
soc: renesas: rcar-sysc: add R8A7745 support
reset: Add Tegra BPMP reset driver
dt-bindings: firmware: Allow child nodes inside the Tegra BPMP
dt-bindings: Add power domains to Tegra BPMP firmware
firmware: tegra: Add BPMP support
firmware: tegra: Add IVC library
dt-bindings: firmware: Add bindings for Tegra BPMP
mailbox: tegra-hsp: Use after free in tegra_hsp_remove_doorbells()
mailbox: Add Tegra HSP driver
firmware: arm_scpi: add support for pre-v1.0 SCPI compatible
...
This contains a patch which implements a reset driver using the services
provided by the BPMP firmware (via the MRQ_RESET request).
-----BEGIN PGP SIGNATURE-----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=t06j
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-4.10-reset' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/drivers
reset: Add Tegra BPMP reset driver
This contains a patch which implements a reset driver using the services
provided by the BPMP firmware (via the MRQ_RESET request).
* tag 'tegra-for-4.10-reset' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
reset: Add Tegra BPMP reset driver
Signed-off-by: Olof Johansson <olof@lixom.net>
This driver uses the services provided by the BPMP firmware driver to
implement a reset driver based on the MRQ_RESET request.
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Some SoCs (for example Amlogic GXBB) implement a reset controller which
only supports a reset pulse (triggered via reset_control_reset). At the
same time multiple devices (in case of the Amlogic GXBB SoC both USB
PHYs) are sharing the same reset line.
This patch allows using reset_control_reset also for shared resets.
There are limitations though:
reset_control_reset can only be used if reset_control_assert was not
used yet.
reset_control_assert can only be used if reset_control_reset was not
used yet.
For shared resets the reset is only triggered once for the lifetime of
the reset_control instance (the reset can be triggered again if all
consumers of that specific reset_control are gone, as the reset
framework will free the reset_control instance in that case).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The Kconfig currently controlling compilation of this code is:
drivers/reset/Kconfig:config RESET_LPC18XX
drivers/reset/Kconfig: bool "LPC18xx/43xx Reset Driver" if COMPILE_TEST
drivers/reset/Kconfig: default ARCH_LPC18XX
or
arch/arm/Kconfig:config ARCH_LPC18XX
arch/arm/Kconfig: bool "NXP LPC18xx/LPC43xx"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
We explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and it allows us to drop the ".remove"
code for non-modular drivers.
Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Cc: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The Makefile/Kconfig currently controlling compilation of this code is:
drivers/reset/Kconfig:config RESET_ZYNQ
drivers/reset/Kconfig: bool "ZYNQ Reset Driver" if COMPILE_TEST
drivers/reset/Kconfig: default ARCH_ZYNQ
or
drivers/reset/Makefile:obj-$(CONFIG_ARCH_ZYNQ) += reset-zynq.o
arch/arm/mach-zynq/Kconfig:config ARCH_ZYNQ
arch/arm/mach-zynq/Kconfig: bool "Xilinx Zynq ARM Cortex A9 Platform" if ARCH_MULTI_V7
...meaning that it currently is not being built as a module by anyone.
Lets remove the few remaining traces of modular macro usage, so that
when reading the driver there is no doubt it is builtin-only.
Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.
We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
Cc: "Sören Brinkmann" <soren.brinkmann@xilinx.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Moritz Fischer <moritz.fischer@ettus.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The Kconfig currently controlling compilation of this code is:
drivers/reset/Kconfig:config RESET_SUNXI
drivers/reset/Kconfig: bool "Allwinner SoCs Reset Driver" if COMPILE_TEST && !ARCH_SUNXI
drivers/reset/Kconfig: default ARCH_SUNXI
or
arch/arm/mach-sunxi/Kconfig:menuconfig ARCH_SUNXI
arch/arm/mach-sunxi/Kconfig: bool "Allwinner SoCs" if ARCH_MULTI_V7
...meaning that it currently is not being built as a module by anyone.
Lets remove the few remaining traces of modular macro usage, so that
when reading the driver there is no doubt it is builtin-only.
Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The Kconfig currently controlling compilation of this code is:
drivers/reset/Kconfig:config RESET_SOCFPGA
drivers/reset/Kconfig: bool "SoCFPGA Reset Driver" if COMPILE_TEST
drivers/reset/Kconfig: default ARCH_SOCFPGA
or
arch/arm/mach-socfpga/Kconfig:menuconfig ARCH_SOCFPGA
arch/arm/mach-socfpga/Kconfig: bool "Altera SOCFPGA family" if ARCH_MULTI_V7
...meaning that it currently is not being built as a module by anyone.
Lets remove the small amount of modular evidence that remains, so that
when reading the driver there is no doubt it is builtin-only.
Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.
We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
Cc: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The Kconfig currently controlling compilation of this code is:
drivers/reset/Kconfig:config RESET_BERLIN
drivers/reset/Kconfig: bool "Berlin Reset Driver" if COMPILE_TEST
drivers/reset/Kconfig: default ARCH_BERLIN
or
arch/arm/mach-berlin/Kconfig:menuconfig ARCH_BERLIN
arch/arm/mach-berlin/Kconfig: bool "Marvell Berlin SoCs" if ARCH_MULTI_V7
or
arch/arm64/Kconfig.platforms:config ARCH_BERLIN
arch/arm64/Kconfig.platforms: bool "Marvell Berlin SoC Family"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
Cc: Antoine Tenart <antoine.tenart@free-electrons.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
I made a mistake as for naming for this block. The MIO block is not
implemented for these 3 SoCs in the first place. The current naming
will be a trouble if an SoC with both MIO and SD-ctrl blocks appear
in the future.
This driver has just been merged in the previous merge window.
Rename it before the release.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
In order to support the Oxford Semiconductor OX820 SoC, add a new
compatible string.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Support for STiH415/6 SoCs is being removed from the
kernel because the platforms are obsolete. This patch removes
the reset drivers for these SoC's.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Also remove the RESET_CONTROLLER dependency, this Kconfig file is
included inside the menuconfig already.
Cc: Chen Feng <puck.chen@hisilicon.com>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Visible only if COMPILE_TEST is enabled, this allows to include the
driver in build tests.
Cc: Moritz Fischer <moritz.fischer@ettus.com>
Cc: Sören Brinkmann <soren.brinkmann@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Visible only if COMPILE_TEST is enabled, this allows to include the
driver in build tests.
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Visible only if COMPILE_TEST is enabled, this allows to include the
driver in build tests.
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Gabriel Fernandez <gabriel.fernandez@st.com>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Visible only if COMPILE_TEST is enabled, this allows to include the
driver in build tests.
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Visible only if COMPILE_TEST is enabled, this allows to include the
driver in build tests.
Cc: Damien Horsley <Damien.Horsley@imgtec.com>
Acked-by: James Hartley <james.hartley@imgtec.com>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Visible only if COMPILE_TEST is enabled, this allows to include the
driver in build tests.
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Visible only if COMPILE_TEST is enabled, this allows to include the
driver in build tests.
Acked-by: Joachim Eastwood <manabian@gmail.com>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Visible only if COMPILE_TEST is enabled, this allows to include the
driver in build tests.
Cc: Antoine Tenart <antoine.tenart@free-electrons.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Visible only if COMPILE_TEST is enabled, this allows to include the
driver in build tests.
Acked-by: Aban Bedel <albeu@free.fr>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The driver uses readl/writel, so it should include linux/io.h.
Acked-by: Aban Bedel <albeu@free.fr>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Instead of potentially crashing, dump a backtrace and return -EINVAL if
rstc is NULL or an error code.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
This is the initial commit for UniPhier reset controller driver.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The STM32 MCUs family IPs can be reset by accessing some registers
from the RCC block.
The list of available reset lines is documented in the DT bindings.
Signed-off-by: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Since we can just add it to membase once, there is no need to store
modrst_offset separately, and to repeat the addition with every access.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Add a reset-controller driver for performing reset management of
various devices present on the SoC, with the reset registers shared
between devices in a common register memory space. This driver uses
the syscon/regmap frameworks to actually implement the various reset
functionalities needed by the reset consumer devices.
Signed-off-by: Andrew F. Davis <afd@ti.com>
[s-anna@ti.com: add documentation, syscon name change]
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
There are two reset controllers in hi6220 SoC:
The peripheral reset controller bits are part of sysctrl registers.
The media reset controller bits are part of mediactrl registers.
So change register access to syscon way.
And rename current reset controller to peripheral one.
Signed-off-by: Chen Feng <puck.chen@hisilicon.com>
Signed-off-by: Xia Qing <saberlily.xia@hisilicon.com>
Signed-off-by: Xinliang Liu <xinliang.liu@linaro.org>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
This patch adds the platform driver for the Amlogic Meson SoC Reset
Controller.
The Meson8b and GXBB SoCs are supported.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Use the brand new devm_reset_controller_register() API to get rid of
the platform driver remove callback.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
In "make menuconfig", reset drivers are currently lined up together
with the reset sub-system menu, like this:
-*- Reset Controller Support ----
< > Hi6220 Reset Driver
(It also means, the menu "Reset Controller Support" is always empty.)
"Hi6220 Reset Driver" should go into the sub-menu of the
"Reset Controller Support".
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Use devm_reset_controller_register() for the reset controller
registration and drop the .remove callback.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Use devm_reset_controller_register() for the reset controller
registration and drop the .remove callback.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Use devm_reset_controller_register() for the reset controller
registration and drop the .remove callback.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Use devm_reset_controller_register() for the reset controller
registration and drop the .remove callback.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Use devm_reset_controller_register() for the reset controller
registration and remove the unregister call from the .remove callback.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Add a device managed API for reset_controller_register().
This helps in reducing code in .remove callbacks and sometimes
dropping .remove callbacks entirely.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Add System reset controller driver for Oxford Semiconductor OXNAS SoC
Family.
CC: Ma Haijun <mahaijuns@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Moving the notifier_block into the drivers priv struct allows us
to retrive the priv struct with container_of and remove the
global variables.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
In some SoCs some hw-blocks share a reset control. Add support for this
setup by adding new:
reset_control_get_shared()
devm_reset_control_get_shared()
devm_reset_control_get_shared_by_index()
methods to get a reset_control. Note that this patch omits adding of_
variants, if these are needed later they can be easily added.
This patch also changes the behavior of the existing exclusive
reset_control_get() variants, if these are now called more then once
for the same reset_control they will return -EBUSY. To catch existing
drivers triggering this error (there should not be any) a WARN_ON(1)
is added in this path.
When a reset_control is shared, the behavior of reset_control_assert /
deassert is changed, for shared reset_controls these will work like the
clock-enable/disable and regulator-on/off functions. They will keep a
deassert_count, and only (re-)assert the reset after reset_control_assert
has been called as many times as reset_control_deassert was called.
Calling reset_control_assert without first calling reset_control_deassert
is not allowed on a shared reset control. Calling reset_control_reset is
also not allowed on a shared reset control.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Now that struct reset_control no longer stores the device pointer for
the device calling reset_control_get we can share a single struct
reset_control when multiple calls to reset_control_get are made for
the same reset line (same id / index).
This is a preparation patch for adding support for shared reset lines.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
With both the regular, _by_index and _optional variants we already have
quite a few variants of [of_]reset_control_get[_foo], the upcoming
addition of shared reset lines support makes this worse.
This commit changes all the variants into wrappers around common core
functions. For completeness sake this commit also adds a new
devm_get_reset_control_by_index wrapper.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The ath79_reset_ops structure is never modified. Make it const.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Alban Bedel <albeu@free.fr>
The lpc18xx_rgu_ops structure is never modified. Make it const.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Joachim Eastwood <manabian@gmail.com>
The sunxi_reset_ops structure is never modified. Make it const.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The pistachio_reset_ops structure is never modified. Make it const.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: James Hartley <james.hartley@imgtec.com>
The berlin_reset_ops structure is never modified. Make it const.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Antoine Tenart <antoine.tenart@free-electrons.com>
The newly added hisilicon reset driver missed the subsystem-wide
fixup by commit d1f15aa095 ("reset: check return value of
reset_controller_register()"). So fix it now.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The core currently doesn't check that the DT cell size matches what the
driver declares, which means that every xlate function needs to duplicate
that check.
Make sure that of_reset_control_get checks for this to avoid duplication
and errors.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
There is no need to initialize rstc, as it is unconditionally
assigned the return value of a kzalloc call before use.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
We need to include <linux/module.h> to build the driver as a loadable
module:
drivers/reset/hisilicon/hi6220_reset.c:108:1: warning: data definition has no type or storage class
postcore_initcall(hi6220_reset_init);
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add a system restart handler that use the FULL_CHIP_RESET bit of the
reset controller.
Signed-off-by: Alban Bedel <albeu@free.fr>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Add reset driver for hi6220-hikey board,this driver supply deassert
of IP on hi6220 SoC.
Signed-off-by: Chen Feng <puck.chen@hisilicon.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Commit 0c5b2b915a ("reset: Mark function as static and remove unused
function in core.c") removed the only user of the device pointer in
struct reset_control. As it is now unused, remove it.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Currently, reset_controller_register() always return 0, but it would
be better to check its return code.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The directory drivers/reset/ is guarded by CONFIG_RESET_CONTROLLER
in driver/Makefile.
CONFIG_RESET_CONTROLLER is boolean, so it always evaluates to 'y'
in drivers/reset/Makefile.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
ENOSYS is reserved to report invalid syscalls to userspace.
Consistently return ENOTSUPP to indicate that the driver doesn't support
the functionality or the reset framework is not enabled at all.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Since this array is static const, it should be marked as __initconst.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This just fixes a checkpatch warning, no functional change.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
When of_reset_control_get() is called without connection ID it returns
-ENOENT when the 'resets' property doesn't exists or is an empty entry.
However when a connection ID is given it returns -EINVAL when the 'resets'
property doesn't exists or the requested name can't be found. This is
because the error code returned by of_property_match_string() is just
passed down as an index to of_parse_phandle_with_args(), which then
returns -EINVAL.
To get a consistent return value with both code paths we must return
-ENOENT when of_property_match_string() fails.
Signed-off-by: Alban Bedel <albeu@free.fr>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Add of_reset_control_get_by_index() to allow the drivers to get reset
device without knowing its name.
Signed-off-by: Vince Hsu <vinceh@nvidia.com>
[jonathanh@nvidia.com: Updated stub function to return -ENOTSUPP instead
of -ENOSYS which should only be used for system calls.]
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
This adds a reset controller driver to control the Xilinx Zynq
AP-SoC's various resets.
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The AR71XX/AR9XXX SoC have a simple reset controller with one bit per
reset line.
Signed-off-by: Alban Bedel <albeu@free.fr>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
In order for the Arria10 to be able to re-use the reset driver for SoCFPGA
Cyclone5/Arria5, we need to read the 'altr,modrst-offset' property from the
device tree entry. The 'altr,modrst-offset' property is the first register
into the reset manager that is used for bringing peripherals out of reset.
The driver assumes a modrst-offset of 0x10 in order to support legacy
Cyclone5/Arria5 hardware.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Add reset driver for the Reset Generation Unit (RGU) found on NXP
LPC18xx and LPC43xx devies. This reset controller features up to 64
reset lines connected to different blocks and peripheral in the SoC.
Most reset lines on the controller are self clearing except for
those dealing with the Cortex-M0 cores on LPC43xx devices.
This driver also registers a restart handler that can be used to
reset the entire device.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
By popular vote, the DT binding includes for reset controllers are located
in include/dt-bindings/reset/. Move the STi reset constants in there, too,
to avoid confusion.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
With proper platform driver probing for berlin reset driver, drop the
arch_initcall workaround.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
The Berlin reset controller was introduced without being a platform
driver because of a needed DT rework: the node describing the reset
controller also describes the pinctrl and clk controllers...
Prepare conversion by adding a platform driver probe to a new
compatible "marvell,berlin2-reset" with syscon regmap.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Call spin_lock_init() before the spinlocks are used, both in early init
and probe functions preventing a lockdep splat.
I have been observing lockdep complaining [1] during boot on my a80 optimus [2]
when CONFIG_PROVE_LOCKING has been enabled. This patch resolves the splat,
and has been tested on a few other sunxi platforms without issue.
[1] http://storage.kernelci.org/next/next-20150107/arm-multi_v7_defconfig+CONFIG_PROVE_LOCKING=y/lab-tbaker/boot-sun9i-a80-optimus.html
[2] http://kernelci.org/boot/?a80-optimus
Signed-off-by: Tyler Baker <tyler.baker@linaro.org>
Cc: <stable@vger.kernel.org>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=FuM7
-----END PGP SIGNATURE-----
Merge tag 'reset-for-3.19-2' of git://git.pengutronix.de/git/pza/linux into next/drivers
Pull "Reset controller changes for v3.19" from Philipp Zabel:
This adds a new driver for the sti soc family, and creates
a reset_control_status interface, which is added to the existing
drivers.
* tag 'reset-for-3.19-2' of git://git.pengutronix.de/git/pza/linux:
reset: add socfpga_reset_status
reset: sti: Document sti-picophyreset controllers bindings.
reset: stih407: Add softreset, powerdown and picophy controllers
reset: stih407: Add reset controllers DT bindings
reset: add reset_control_status helper function
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Populate the reset_status callback for SOCFPGA.
Signed-off-by: Alan Tull <atull@opensource.altera.com>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
This tag adds support to STiH407 reset controllers:
1. st,stih407-powerdown
2. st,stih407-softreset
3. st,stih407-picophyreset
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=aZN5
-----END PGP SIGNATURE-----
Merge tag 'sti-reset-for-v3.19-1' of git://git.stlinux.com/devel/kernel/linux-sti into reset/for_v3.19
STi reset controller updates for v3.19.
This tag adds support to STiH407 reset controllers:
1. st,stih407-powerdown
2. st,stih407-softreset
3. st,stih407-picophyreset
This patch adds softreset, powerdown and picophy reset controllers for
the STiH407 SoC.
With this patch three new devices are registered: -
1. st,stih407-powerdown
2. st,stih407-softreset
3. st,stih407-picophyreset
All three devices use system configuration registers mapped via regmap to
perform the reset or powerdown. The powerdown controller also has
an acknowledgement.
A separate picophy reset controller manages the different reset channels within
the picophy, which have a different polarity to the other system softresets.
Managing these different picophy softreset channels is necessary to correctly
handle resuming from suspend when USB2 devices are plugged into the USB3 port.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Add a reset controller for Marvell Berlin SoCs which is used by the
USB PHYs drivers (for now).
Signed-off-by: Antoine Ténart <antoine.tenart@free-electrons.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
There are cases where a system will want to read a reset status bit before
doing any other toggling. Add a reset_control_status helper function to the
reset controller API.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
SoC-near driver changes that we're merging through our tree. Mostly
because they depend on other changes we have staged, but in some cases
because the driver maintainers preferred that we did it this way.
This contains a largeish cleanup series of the omap_l3_noc bus driver,
cpuidle rework for Exynos, some reset driver conversions and a long
branch of TI EDMA fixes and cleanups, with more to come next release.
The TI EDMA cleanups is a shared branch with the dmaengine tree, with
a handful of Davinci-specific fixes on top.
After discussion at last year's KS (and some more on the mailing lists),
we are here adding a drivers/soc directory. The purpose of this is
to keep per-vendor shared code that's needed by different drivers but
that doesn't fit into the MFD (nor drivers/platform) model. We expect
to keep merging contents for this hierarchy through arm-soc so we can
keep an eye on what the vendors keep adding here and not making it a
free-for-all to shove in crazy stuff.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=SC+e
-----END PGP SIGNATURE-----
Merge tag 'drivers-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc into next
Pull ARM SoC driver changes from Olof Johansson:
"SoC-near driver changes that we're merging through our tree. Mostly
because they depend on other changes we have staged, but in some cases
because the driver maintainers preferred that we did it this way.
This contains a largeish cleanup series of the omap_l3_noc bus driver,
cpuidle rework for Exynos, some reset driver conversions and a long
branch of TI EDMA fixes and cleanups, with more to come next release.
The TI EDMA cleanups is a shared branch with the dmaengine tree, with
a handful of Davinci-specific fixes on top.
After discussion at last year's KS (and some more on the mailing
lists), we are here adding a drivers/soc directory. The purpose of
this is to keep per-vendor shared code that's needed by different
drivers but that doesn't fit into the MFD (nor drivers/platform)
model. We expect to keep merging contents for this hierarchy through
arm-soc so we can keep an eye on what the vendors keep adding here and
not making it a free-for-all to shove in crazy stuff"
* tag 'drivers-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (101 commits)
cpufreq: exynos: Fix driver compilation with ARCH_MULTIPLATFORM
tty: serial: msm: Remove direct access to GSBI
power: reset: keystone-reset: introduce keystone reset driver
Documentation: dt: add bindings for keystone pll control controller
Documentation: dt: add bindings for keystone reset driver
soc: qcom: fix of_device_id table
ARM: EXYNOS: Fix kernel panic when unplugging CPU1 on exynos
ARM: EXYNOS: Move the driver to drivers/cpuidle directory
ARM: EXYNOS: Cleanup all unneeded headers from cpuidle.c
ARM: EXYNOS: Pass the AFTR callback to the platform_data
ARM: EXYNOS: Move S5P_CHECK_SLEEP into pm.c
ARM: EXYNOS: Move the power sequence call in the cpu_pm notifier
ARM: EXYNOS: Move the AFTR state function into pm.c
ARM: EXYNOS: Encapsulate the AFTR code into a function
ARM: EXYNOS: Disable cpuidle for exynos5440
ARM: EXYNOS: Encapsulate boot vector code into a function for cpuidle
ARM: EXYNOS: Pass wakeup mask parameter to function for cpuidle
ARM: EXYNOS: Remove ifdef for scu_enable in pm
ARM: EXYNOS: Move scu_enable in the cpu_pm notifier
ARM: EXYNOS: Use the cpu_pm notifier for pm
...
Merge "Allwinner drivers changes for 3.16" from Maxime Ripard:
Reset drivers for the A31, that have been merged with reset maintainer's
Acked-by.
* 'sunxi/drivers-for-3.16' of https://github.com/mripard/linux:
reset: sunxi: allow MFD subdevices probe
reset: sunxi: document sunxi's reset controllers bindings
Signed-off-by: Olof Johansson <olof@lixom.net>
Add keyscan reset on stih416 reset controller.
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Giuseppe Condorelli <giuseppe.condorelli@st.com>
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Add keyscan reset on stih415 reset controller.
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Giuseppe Condorelli <giuseppe.condorelli@st.com>
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
The current implementation uses sunxi_reset_init function for both early
init and platform device probe.
The sunxi_reset_init function uses DT to retrieve device resources, which
will be an issue if reset controllers are registered from an MFD device
that define resources from mfd_cell definition.
Moreover, we can make of devm functions when we're in the probe context.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Add a reset-controller driver for the socfpga platform.
The reset-controller has four banks with up to 32 entries all encapsulated in
one module block.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
---
Notes:
Changes since v2:
- remove superfluous ret in probe function
- add Acked-by
Changes since v1:
- use BITS_PER_LONG everywhere instead of MAX_BANK_WIDTH
- print pdev->dev.of_node->full_name on error
- use proper IS_ERR/PTR_ERR
Merge "reset controller fixes and updates" from Philipp Zabel:
* 'reset/for_v3.15' of git://git.pengutronix.de/git/pza/linux:
reset: Add optional resets and stubs
reset: Add of_reset_control_get
reset: Mark function as static and remove unused function in core.c
reset: allow drivers to request probe deferral
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch adds softreset controller for STiH416 SOC, soft reset
controller is based on system configuration registers which are mapped
via regmap. This reset controller does not have any feedback or
acknowledgement. With this patch a new device "st,stih416-softreset" is
registered with system configuration registers based reset controller
that controls the softreset state of the hardware such as Ethernet, IRB.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
This patch adds softreset controller for STiH415 SOC, soft reset
controller is based on system configuration registers which are mapped
via regmap. This reset controller does not have any feedback or
acknowledgement. With this patch a new device "st,stih415-softreset" is
registered with system configuration registers based reset controller
that controls the softreset state of the hardware such as Ethernet, IRB.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
This patch adds a reset controller platform driver for the STiH416
SoC. This initial version provides a compatible driver for the
"st,stih416-powerdown" device, which registers a system configuration
register based reset controller that controls the powerdown state of
hardware such as the on-chip USB host controllers.
Signed-off-by: Stephen Gallimore <stephen.gallimore@st.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
This patch adds a reset controller platform driver for the STiH415
SoC. This initial version provides a compatible driver for the
"st,stih415-powerdown" device, which registers a system configuration
register based reset controller that controls the powerdown state of
hardware such as the on-chip USB host controllers.
Signed-off-by: Stephen Gallimore <stephen.gallimore@st.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
This patch adds a reset controller implementation for STMicroelectronics
STi family SoCs; it allows a group of related reset like controls found
in multiple system configuration registers to be represented by a single
controller device. System configuration registers are accessed through
the regmap framework and the mfd/syscon driver.
The implementation optionally supports waiting for the reset action to
be acknowledged in a separate status register and supports both
active high and active low reset lines. These properties are common across
all the reset channels in a specific reset controller instance, hence
all channels in a paritcular controller are expected to behave in the
same way.
Signed-off-by: Stephen Gallimore <stephen.gallimore@st.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
In some cases, you might need to deassert from reset an hardware block that
doesn't associated to a struct device (CPUs, timers, etc.).
Add a small helper to retrieve the reset controller from the device tree
without the need to pass a struct device.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Mark function of_reset_simple_xlate() as static in core.c
because it is not used outside this file.
Also, remove functions devm_reset_control_put() and
devm_reset_control_match() because they are unused.
This eliminates the following warnings in core.c:
drivers/reset/core.c:46:5: warning: no previous prototype for ‘of_reset_simple_xlate’ [-Wmissing-prototypes]
drivers/reset/core.c:262:6: warning: no previous prototype for ‘devm_reset_control_put’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
If the requested reset controller is not yet available, have reset_control_get
and device_reset return -EPROBE_DEFER so the driver can decide to request
probe deferral.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
The Allwinner A31 and most of the other Allwinner SoCs have an IP
maintaining a few other IPs in the SoC in reset by default. Among these
IPs are the A31's High Speed Timers, hence why we can't use the regular
driver construct in every cases, and need to call the registering
function directly during machine initialisation.
Apart from this, the implementation is fairly straightforward, and could
easily be moved to a generic MMIO-based reset controller driver if the
need ever arise.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
"rstc" is NULL here and we should use "rcdev" instead of "rstc->rcdev".
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
This adds a simple API for devices to request being reset
by separate reset controller hardware and implements the
reset signal device tree binding.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
