This reverts commit 277a036312.
While fixing old boards with broken DTs, this change will break
newer ones with correct gpio polarity annotation.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Commit 90c2d2eb7a ("MIPS: pci: lantiq: switch to using gpiod API") not
only switched to the gpiod API, but also inverted / changed the polarity
of the GPIO.
According to the PCI specification, the RST# pin is an active-low
signal. However, most of the device trees that have been widely used for
a long time (mainly in the openWrt project) define this GPIO as
active-high and the old driver code inverted the signal internally.
Apparently there are actually boards where the reset gpio must be
operated inverted. For this reason, we cannot use the GPIOD_OUT_LOW/HIGH
flag for initialization. Instead, we must explicitly set the gpio to
value 1 in order to take into account any "GPIO_ACTIVE_LOW" flag that
may have been set.
In order to remain compatible with all these existing device trees, we
should therefore keep the logic as it was before the commit.
Fixes: 90c2d2eb7a ("MIPS: pci: lantiq: switch to using gpiod API")
Cc: stable@vger.kernel.org
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
read_config_dword() contains strange condition checking ret for a
number of values. The ret variable, however, is always zero because
config_access() never returns anything else. Thus, the retry is always
taken until number of tries is exceeded.
The code looks like it wants to check *val instead of ret to see if the
read gave an error response.
Fixes: 73b4390fb2 ("[MIPS] Routerboard 532: Support for base system")
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
The standard PCIe configuration read-write interface is used to
access the configuration space of the peripheral PCIe devices
of the mips processor after the PCIe link surprise down, it can
generate kernel panic caused by "Data bus error". So it is
necessary to add PCIe link status check for system protection.
When the PCIe link is down or in training, assigning a value
of 0 to the configuration address can prevent read-write behavior
to the configuration space of peripheral PCIe devices, thereby
preventing kernel panic.
Signed-off-by: Songyang Li <leesongyang@outlook.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Instead of literal, PCI error value should be set with
PCI_SET_ERROR_RESPONSE(). Use it in tx4927_pci_config_read().
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmal.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
pci_ops .read/.write must return PCIBIOS_* codes but
tx4927_pci_config_read/write() return -1 when mkaddr() cannot find
devfn from the root bus. Return PCIBIOS_DEVICE_NOT_FOUND instead and
pass that onward in the call chain instead of overwriting the return
value.
Also converts 0 -> PCIBIOS_SUCCESSFUL which has only cosmetic impact.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmal.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
pcibios_plat_dev_init() is called from pcibios_enable_device() that
should return normal errnos, not PCIBIOS return codes. In this case the
impact is only cosmetic because PCIBIOS_SUCCESSFUL equals 0 that is
success code with errnos as well. Nonetheless, remove the inconsistency
by replacing the PCIBIOS_SUCCESSFUL with 0.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmal.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Ever since introduction in the commit e47d488935 ("MIPS: Lantiq: Add
PCI controller support.") ltqpci_plat_dev_init has been unused. In
57c8cb8f24 ("MIPS: pci: convert lantiq driver to OF") also
ltq_pci_plat_arch_init was introduced.
With those commit being more than 10 years ago, it seem neither is
going to get used anytime soon. Thus, remove both unused function
pointer variables.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmal.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Fix typos, most reported by "codespell arch/mips". Only touches comments,
no code changes.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: linux-mips@vger.kernel.org
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
With the adding, some default ioremap_xx methods defined in
asm-generic/io.h can be used. E.g the default ioremap_uc() returning
NULL.
We also massaged various headers to avoid nested includes.
Signed-off-by: Baoquan He <bhe@redhat.com>
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
[jiaxun.yang@flygoat.com: Massage more headers, fix ioport defines]
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Huacai Chen <chenhuacai@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: linux-arch@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
arch/mips/pci/fixup-lantiq.c requires nothing from <linux/of_irq.h>, so
remove the include of it.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
After bbd8810d39 ("PCI: Remove unused includes and superfluous struct
declaration"), <linux/of_pci.h> no longer includes <linux/pci.h>, which
provides the extern declarations for pcibios_plat_dev_init() and
pcibios_map_irq() via <asm/pci.h>.
This results in these new warnings:
arch/mips/pci/fixup-lantiq.c:13:5: warning: no previous prototype for 'pcibios_plat_dev_init' [-Wmissing-prototypes]
arch/mips/pci/fixup-lantiq.c:24:5: warning: no previous prototype for 'pcibios_map_irq' [-Wmissing-prototypes]
Include <linux/pci.h> directly to get these declarations.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202310070445.tzRBNYRC-lkp@intel.com/
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
SWIOTLB implementation details should not be exposed to the rest of the
kernel. This will allow to make changes to the implementation without
modifying non-swiotlb code.
To avoid breaking existing users, provide helper functions for the few
required fields.
As a bonus, using a helper function to initialize struct device allows to
get rid of an #ifdef in driver core.
Signed-off-by: Petr Tesarik <petr.tesarik.ext@huawei.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it was merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Usually, We only need to print the error log when there is a PCIe card but
initialization fails. Whether the driver finds the PCIe card or not is the
expected behavior. So it's better to log these information with dev_info().
Tested on MT7628AN router Motorola MWR03.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
These codes are used to read NFTS_TIMEOUT_DELAY register value and
write it into kernel log after writing the register. they are only
used for debugging during driver development, so there is no need
to keep them now.
Tested on MT7628AN router Motorola MWR03.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
While destroying alignment of the assignments in bridge_driver, do it
consistently and use a single space before =.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
- added support for virt board aligned to QEMU MIPS virt board
- added support for doing DMA coherence on a per device base
- reworked handling of RALINK SoCs
- cleanup for Loongon64 barriers
- removed deprecated support for MIPS_CMP SMP handling method
- removed support Sibyte CARMEL and CHRINE boards
- cleanups and fixes
-----BEGIN PGP SIGNATURE-----
iQJOBAABCAA4FiEEbt46xwy6kEcDOXoUeZbBVTGwZHAFAmRI78IaHHRzYm9nZW5k
QGFscGhhLmZyYW5rZW4uZGUACgkQeZbBVTGwZHDG0xAAhXtNUKH6MNgPLm+iOeXu
GIUax2ZdFKl/xbG9kLfSdpKLpdnvdZSQABRIzD0isw3F3ahwOzaql4feNUsdK9oU
eLbzHu5isgtdX03ToOmn3yjgcWr1k/xNGjuW7uaj75CvUZHCqOwt+kDie+3rIMjE
kYHIdszemFnj3VaG6omkVy/tv2pUHSJlVDePVNmmq7yWCXK+t/6CU8QoSlcQIxy9
MAktt735wxJrFW6+ezm0T4lY64IqSpiXVcIOaOHXbJrIRJK4zyEiRleZ2+qIwCw0
jpwc7qth6EeA/LJnJExfurDtH86oQvjpJmSw1QuDKE9h3RZHYE3amRFjGHEMvaZ7
iSsCCKmTITcEWgAAq7GMot4qVSWOIhWpYZfNtpP8WfirZy8RlfyfXrzprcEg3SiO
mBGqsK0s+Y8v/J3d9tDmNRSVOyMyeH3Qsc6feS6YvmWN48jauT+ze06pNFyDO3At
bJWrzhI0UaLETo8hOa2mbnATThEuAUaFwOH1arikJwHkXjuvy1RvZerEtqGupI9y
VubR3gEx2subruInZQU5O3R+ZhogoKnuADfeDtw8MUsUNC+ODAHX0mGCyQXqRf75
ooepecwtZyHFjqh0sw7hz7184+VKeOHS8YRjW9njOXZVtEzM0LikXgECsQzEcVF7
3Y72QFJFt61UtWSd3eJayEg=
=eo9R
-----END PGP SIGNATURE-----
Merge tag 'mips_6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS updates from Thomas Bogendoerfer:
- added support for Huawei B593u-12
- added support for virt board aligned to QEMU MIPS virt board
- added support for doing DMA coherence on a per device base
- reworked handling of RALINK SoCs
- cleanup for Loongon64 barriers
- removed deprecated support for MIPS_CMP SMP handling method
- removed support Sibyte CARMEL and CHRINE boards
- cleanups and fixes
* tag 'mips_6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (59 commits)
MIPS: uprobes: Restore thread.trap_nr
MIPS: Don't clear _PAGE_SPECIAL in _PAGE_CHG_MASK
MIPS: Sink body of check_bugs_early() into its only call site
MIPS: Mark check_bugs() as __init
Revert "MIPS: generic: Enable all CPUs supported by virt board in Kconfig"
MIPS: octeon_switch: Remove duplicated labels
MIPS: loongson2ef: Add missing break in cs5536_isa
MIPS: Remove set_swbp() in uprobes.c
MIPS: Use def_bool y for ARCH_SUPPORTS_UPROBES
MIPS: fw: Allow firmware to pass a empty env
MIPS: Remove deprecated CONFIG_MIPS_CMP
MIPS: lantiq: remove unused function declaration
MIPS: Drop unused positional parameter in local_irq_{dis,en}able
MIPS: mm: Remove local_cache_flush_page
MIPS: Remove no longer used ide.h
MIPS: mm: Remove unused *cache_page_indexed flush functions
MIPS: generic: Enable all CPUs supported by virt board in Kconfig
MIPS: Add board config for virt board
MIPS: Octeon: Disable CVMSEG by default on other platforms
MIPS: Loongson: Don't select platform features with CPU
...
Instead of open-coding it everywhere introduce a tiny helper that can be
used to iterate over each resource of a PCI device, and convert the most
obvious users into it.
While at it drop doubled empty line before pdev_sort_resources().
No functional changes intended.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230330162434.35055-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
It is preferred to use typed property access functions (i.e.
of_property_read_<type> functions) rather than low-level
of_get_property/of_find_property functions for reading properties.
Convert reading boolean properties to to of_property_read_bool().
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Ye Xingchen <ye.xingchen@zte.com.cn>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Ye Xingchen <ye.xingchen@zte.com.cn>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: zhang songyi <zhang.songyi@zte.com.cn>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
This patch switches the driver from legacy gpio API to the newer
gpiod API.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Don't use "/**" kernel-doc notation for comments that are not in
kernel-doc format.
Eliminates one warning:
arch/mips/pci/pci-ar2315.c:6: warning: This comment starts with
'/**', but isn't a kernel-doc comment. Refer
Documentation/doc-guide/kernel-doc.rst
* Both AR2315 and AR2316 chips have PCI interface unit, which supports DMA
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Aditya Srivastava <yashsri421@gmail.com>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: linux-mips@vger.kernel.org
Cc: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Acked-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Rearrange kernel-doc notation for 2 functions to eliminate
kernel-doc warnings. Use Return: notation for the function
return value description. Add function short descriptions
for both functions.
Correct 2 typos.
Fixes these kernel-doc warnings:
msi-octeon.c:49: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* Called when a driver request MSI interrupts instead of the
msi-octeon.c:49: warning: missing initial short description on line:
* Called when a driver request MSI interrupts instead of the
msi-octeon.c:62: warning: No description found for return value of 'arch_setup_msi_irq'
msi-octeon.c:189: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* Called when a device no longer needs its MSI interrupts. All
msi-octeon.c:189: warning: missing initial short description on line:
* Called when a device no longer needs its MSI interrupts. All
Fixes: e8635b484f ("MIPS: Add Cavium OCTEON PCI support.")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Aditya Srivastava <yashsri421@gmail.com>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: linux-mips@vger.kernel.org
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
There is an info message with an extraneous leading space. Remove it.
Also rename pci to PCI.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
-----BEGIN PGP SIGNATURE-----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=hTzI
-----END PGP SIGNATURE-----
Merge tag 'mips_5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS updates from Thomas Bogendoerfer:
"Cleanups and fixes"
* tag 'mips_5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (38 commits)
MIPS: RALINK: Define pci_remap_iospace under CONFIG_PCI_DRIVERS_GENERIC
MIPS: Use memblock_add_node() in early_parse_mem() under CONFIG_NUMA
MIPS: Return -EINVAL if mem parameter is empty in early_parse_mem()
MIPS: Kconfig: Fix indentation and add endif comment
MIPS: bmips: Fix compiler warning observed on W=1 build
MIPS: Rewrite `csum_tcpudp_nofold' in plain C
mips: setup: use strscpy to replace strlcpy
MIPS: Octeon: add SNIC10E board
MIPS: Ingenic: Refresh defconfig for CU1000-Neo and CU1830-Neo.
MIPS: Ingenic: Refresh device tree for Ingenic SoCs and boards.
MIPS: Ingenic: Add PWM nodes for X1830.
MIPS: Octeon: fix typo in comment
MIPS: loongson32: Kconfig: Remove extra space
MIPS: Sibyte: remove unnecessary return variable
MIPS: Use NOKPROBE_SYMBOL() instead of __kprobes annotation
selftests/ftrace: Save kprobe_events to test log
MIPS: tools: no need to initialise statics to 0
MIPS: Loongson: Use hwmon_device_register_with_groups() to register hwmon
MIPS: VR41xx: Drop redundant spinlock initialization
MIPS: smp: optimization for flush_tlb_mm when exiting
...
Spelling mistake (triple letters) in comment.
Detected with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Various spelling mistakes in comments.
Detected with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Use the generic swiotlb initialization helper instead of open coding it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Tested-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
-----BEGIN PGP SIGNATURE-----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=5Q9H
-----END PGP SIGNATURE-----
Merge tag 'pci-v5.18-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Move the VGA arbiter from drivers/gpu to drivers/pci because it's
PCI-specific, not GPU-specific (Bjorn Helgaas)
- Select the default VGA device consistently whether it's enumerated
before or after VGA arbiter init, which fixes arches that enumerate
PCI devices late (Huacai Chen)
Resource management:
- Support BAR sizes up to 8TB (Dongdong Liu)
PCIe native device hotplug:
- Fix "Command Completed" tracking to avoid spurious timouts when
powering off empty slots (Liguang Zhang)
- Quirk Qualcomm devices that don't implement Command Completed
correctly, again to avoid spurious timeouts (Manivannan Sadhasivam)
Peer-to-peer DMA:
- Add Intel 3rd Gen Intel Xeon Scalable Processors to whitelist
(Michael J. Ruhl)
APM X-Gene PCIe controller driver:
- Revert generic DT parsing changes that broke some machines in the
field (Marc Zyngier)
Freescale i.MX6 PCIe controller driver:
- Allow controller probe to succeed even when no devices currently
present to allow hot-add later (Fabio Estevam)
- Enable power management on i.MX6QP (Richard Zhu)
- Assert CLKREQ# on i.MX8MM so enumeration doesn't hang when no
device is connected (Richard Zhu)
Marvell Aardvark PCIe controller driver:
- Fix MSI and MSI-X support (Marek Behún, Pali Rohár)
- Add support for ERR and PME interrupts (Pali Rohár)
Marvell MVEBU PCIe controller driver:
- Add DT binding and support for "num-lanes" (Pali Rohár)
- Add support for INTx interrupts (Pali Rohár)
Microsoft Hyper-V host bridge driver:
- Avoid unnecessary hypercalls when unmasking IRQs on ARM64 (Boqun
Feng)
Qualcomm PCIe controller driver:
- Add SM8450 DT binding and driver support (Dmitry Baryshkov)
Renesas R-Car PCIe controller driver:
- Help the controller get to the L1 state since the hardware can't do
it on its own (Marek Vasut)
- Return PCI_ERROR_RESPONSE (~0) for reads that fail on PCIe (Marek
Vasut)
SiFive FU740 PCIe controller driver:
- Drop redundant '-gpios' from DT GPIO lookup (Ben Dooks)
- Force 2.5GT/s for initial device probe (Ben Dooks)
Socionext UniPhier Pro5 controller driver:
- Add NX1 DT binding and driver support (Kunihiko Hayashi)
Synopsys DesignWare PCIe controller driver:
- Restore MSI configuration so MSI works after resume (Jisheng
Zhang)"
* tag 'pci-v5.18-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (94 commits)
x86/PCI: Add #includes to asm/pci_x86.h
PCI: ibmphp: Remove unused assignments
PCI: cpqphp: Remove unused assignments
PCI: fu740: Remove unused assignments
PCI: kirin: Remove unused assignments
PCI: Remove unused assignments
PCI: Declare pci_filp_private only when HAVE_PCI_MMAP
PCI: Avoid broken MSI on SB600 USB devices
PCI: fu740: Force 2.5GT/s for initial device probe
PCI: xgene: Revert "PCI: xgene: Fix IB window setup"
PCI: xgene: Revert "PCI: xgene: Use inbound resources for setup"
PCI: imx6: Assert i.MX8MM CLKREQ# even if no device present
PCI: imx6: Invoke the PHY exit function after PHY power off
PCI: rcar: Use PCI_SET_ERROR_RESPONSE after read which triggered an exception
PCI: rcar: Finish transition to L1 state in rcar_pcie_config_access()
PCI: dwc: Restore MSI Receiver mask during resume
PCI: fu740: Drop redundant '-gpios' from DT GPIO lookup
PCI/VGA: Replace full MIT license text with SPDX identifier
PCI/VGA: Use unsigned format string to print lock counts
PCI/VGA: Log bridge control messages when adding devices
...
The only usage of ar2315_pci_irq_domain_ops is to pass its address to
irq_domain_add_linear() which takes a pointer to const struct
irq_domain_ops. Make it const to allow the compiler to put it in
read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Add these PCI class codes to pci_ids.h:
PCI_CLASS_BRIDGE_PCI_NORMAL
PCI_CLASS_BRIDGE_PCI_SUBTRACTIVE
Use these defines in all kernel code for describing PCI class codes for
normal and subtractive PCI bridges.
[bhelgaas: similar change in pci-mvebu.c]
Link: https://lore.kernel.org/r/20220214114109.26809-1-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
- added MIPS support for brcmstb PCIe controller
- added Loongson 2K1000 reset driver
- removed board support for rbtx4938/rbtx4939
- removed support for TX4939 SoCs
- fixes and cleanups
-----BEGIN PGP SIGNATURE-----
iQJOBAABCAA4FiEEbt46xwy6kEcDOXoUeZbBVTGwZHAFAmHhNi8aHHRzYm9nZW5k
QGFscGhhLmZyYW5rZW4uZGUACgkQeZbBVTGwZHDjGBAAogFGgNYUSzLUHQfGdBcx
fk/Lo+psvZ03cz5i9L4+7D0N3/K55/GXhSvDIHMhbYX41qklCy/ie+hxp3rwbjD3
RTLV3D4YdoJkcn+lPcKgtvGxKXjLE0A2ho/TmrAce2mvrei3BWu7dDmJC0WFjmt7
SZeg3ALjEdYVObO3vaN3pBMuuUuNvYS8DlLadzGwx1rDPHxGOZBri025bl9g6I+m
rQHSTa3p5DY4VsqEOXy1fUZchys1pZC6D7Ja4FPracnxYF0F4jLoWVhN+xt4QpcW
Q6o4+ykIDuL6kEKOwfTB094CeumIZSpcEwIKRYorIHeApG/XdgVBxJfcsaxBxI7V
4KYBkxG93AWwsp9CtxGEfOADoX3XnRbMZk58d6pVW7KUPXNin73jghxkc4vmaK1R
9lDyiq8RC8sh+HA5jkksCmf4otXstVlZGxNMKG3/qJy62pqEuFOIoB1Q8hN15c7w
HlFM7ZFf/6ZWVWm3dSKdB+hZNWTBVL2ucH9bf4s6f408Mj2sMMRIuFUKH/zJzVZZ
SeXy+tv5BcWbU+1EdaHzQJWM69iBCxasNyhPJkk3Hq+vqZdjkdPruzD3pVxdm169
E6cBUSWjwrJTt8EsBWKb1+hzjZk56Brff+9AlhbLWSChto/4SJmT/wZWGvTC2hqS
GBIIDNnd2G5k5xhuVs6qQIM=
=wsIG
-----END PGP SIGNATURE-----
Merge tag 'mips_5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS updates from Thomas Bogendoerfer:
- add support for more BCM47XX based devices
- add MIPS support for brcmstb PCIe controller
- add Loongson 2K1000 reset driver
- remove board support for rbtx4938/rbtx4939
- remove support for TX4939 SoCs
- fixes and cleanups
* tag 'mips_5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (59 commits)
MIPS: ath79: drop _machine_restart again
PCI: brcmstb: Augment driver for MIPs SOCs
MIPS: bmips: Remove obsolete DMA mapping support
MIPS: bmips: Add support PCIe controller device nodes
dt-bindings: PCI: Add compatible string for Brcmstb 74[23]5 MIPs SOCs
MIPS: compressed: Fix build with ZSTD compression
MIPS: BCM47XX: Add support for Netgear WN2500RP v1 & v2
MIPS: BCM47XX: Add support for Netgear R6300 v1
MIPS: BCM47XX: Add LEDs and buttons for Asus RTN-10U
MIPS: BCM47XX: Add board entry for Linksys WRT320N v1
MIPS: BCM47XX: Define Linksys WRT310N V2 buttons
MIPS: Remove duplicated include in local.h
MIPS: retire "asm/llsc.h"
MIPS: rework local_t operation on MIPS64
MIPS: fix local_{add,sub}_return on MIPS64
mips/pci: remove redundant ret variable
MIPS: Loongson64: Add missing of_node_put() in ls2k_reset_init()
MIPS: new Kconfig option ZBOOT_LOAD_ADDRESS
MIPS: enable both vmlinux.gz.itb and vmlinuz for generic
MIPS: signal: Return immediately if call fails
...
Treewide cleanup and consolidation of MSI interrupt handling in
preparation for further changes in this area which are necessary to:
- address existing shortcomings in the VFIO area
- support the upcoming Interrupt Message Store functionality which
decouples the message store from the PCI config/MMIO space
-----BEGIN PGP SIGNATURE-----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=vKzd
-----END PGP SIGNATURE-----
Merge tag 'irq-msi-2022-01-13' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull MSI irq updates from Thomas Gleixner:
"Rework of the MSI interrupt infrastructure.
This is a treewide cleanup and consolidation of MSI interrupt handling
in preparation for further changes in this area which are necessary
to:
- address existing shortcomings in the VFIO area
- support the upcoming Interrupt Message Store functionality which
decouples the message store from the PCI config/MMIO space"
* tag 'irq-msi-2022-01-13' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (94 commits)
genirq/msi: Populate sysfs entry only once
PCI/MSI: Unbreak pci_irq_get_affinity()
genirq/msi: Convert storage to xarray
genirq/msi: Simplify sysfs handling
genirq/msi: Add abuse prevention comment to msi header
genirq/msi: Mop up old interfaces
genirq/msi: Convert to new functions
genirq/msi: Make interrupt allocation less convoluted
platform-msi: Simplify platform device MSI code
platform-msi: Let core code handle MSI descriptors
bus: fsl-mc-msi: Simplify MSI descriptor handling
soc: ti: ti_sci_inta_msi: Remove ti_sci_inta_msi_domain_free_irqs()
soc: ti: ti_sci_inta_msi: Rework MSI descriptor allocation
NTB/msi: Convert to msi_on_each_desc()
PCI: hv: Rework MSI handling
powerpc/mpic_u3msi: Use msi_for_each-desc()
powerpc/fsl_msi: Use msi_for_each_desc()
powerpc/pasemi/msi: Convert to msi_on_each_dec()
powerpc/cell/axon_msi: Convert to msi_on_each_desc()
powerpc/4xx/hsta: Rework MSI handling
...
Return value from rt3883_pci_r32() directly instead
of taking this in another redundant variable.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Signed-off-by: CGEL ZTE <cgel.zte@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
After removal of RBTX4939 board support remove code for the TX4939 SoC.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
The core code provides the same loop code except for the MSI-X reject. Move
that to arch_setup_msi_irq() and remove the duplicated code.
No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Acked-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Link: https://lore.kernel.org/r/20211206210224.319201379@linutronix.de
No active MIPS user own this board, so let's remove it.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
After commit 9f76779f24 ("MIPS: implement architecture-specific
'pci_remap_iospace()'"), there exists the following warning on the
Loongson64 platform:
loongson-pci 1a000000.pci: IO 0x0018020000..0x001803ffff -> 0x0000020000
loongson-pci 1a000000.pci: MEM 0x0040000000..0x007fffffff -> 0x0040000000
------------[ cut here ]------------
WARNING: CPU: 2 PID: 1 at arch/mips/pci/pci-generic.c:55 pci_remap_iospace+0x84/0x90
resource start address is not zero
...
Call Trace:
[<ffffffff8020dc78>] show_stack+0x40/0x120
[<ffffffff80cf4a0c>] dump_stack_lvl+0x58/0x74
[<ffffffff8023a0b0>] __warn+0xe0/0x110
[<ffffffff80cee02c>] warn_slowpath_fmt+0xa4/0xd0
[<ffffffff80cecf24>] pci_remap_iospace+0x84/0x90
[<ffffffff807f9864>] devm_pci_remap_iospace+0x5c/0xb8
[<ffffffff808121b0>] devm_of_pci_bridge_init+0x178/0x1f8
[<ffffffff807f4000>] devm_pci_alloc_host_bridge+0x78/0x98
[<ffffffff80819454>] loongson_pci_probe+0x34/0x160
[<ffffffff809203cc>] platform_probe+0x6c/0xe0
[<ffffffff8091d5d4>] really_probe+0xbc/0x340
[<ffffffff8091d8f0>] __driver_probe_device+0x98/0x110
[<ffffffff8091d9b8>] driver_probe_device+0x50/0x118
[<ffffffff8091dea0>] __driver_attach+0x80/0x118
[<ffffffff8091b280>] bus_for_each_dev+0x80/0xc8
[<ffffffff8091c6d8>] bus_add_driver+0x130/0x210
[<ffffffff8091ead4>] driver_register+0x8c/0x150
[<ffffffff80200a8c>] do_one_initcall+0x54/0x288
[<ffffffff811a5320>] kernel_init_freeable+0x27c/0x2e4
[<ffffffff80cfc380>] kernel_init+0x2c/0x134
[<ffffffff80205a2c>] ret_from_kernel_thread+0x14/0x1c
---[ end trace e4a0efe10aa5cce6 ]---
loongson-pci 1a000000.pci: error -19: failed to map resource [io 0x20000-0x3ffff]
We can see that the resource start address is 0x0000020000, because
the ISA Bridge used the zero address which is defined in the dts file
arch/mips/boot/dts/loongson/ls7a-pch.dtsi:
ISA Bridge: /bus@10000000/isa@18000000
IO 0x0000000018000000..0x000000001801ffff -> 0x0000000000000000
Based on the above analysis, the architecture-specific pci_remap_iospace()
is not suitable for Loongson64, we should only define pci_remap_iospace()
for Ralink on MIPS based on the commit background.
Fixes: 9f76779f24 ("MIPS: implement architecture-specific 'pci_remap_iospace()'")
Suggested-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Tested-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Acked-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
- removed support for Netlogic SOCs
- fixes and cleanup
-----BEGIN PGP SIGNATURE-----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=mvn0
-----END PGP SIGNATURE-----
Merge tag 'mips_5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS updates from Thomas Bogendoerfer:
- added printing of CPU options for /proc/cpuinfo
- removed support for Netlogic SOCs
- fixes and cleanup
* tag 'mips_5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
MIPS: Cobalt: Explain GT64111 early PCI fixup
mips: fix HUGETLB function without THP enabled
mips: cm: Convert to bitfield API to fix out-of-bounds access
MIPS: Remove NETLOGIC support
MIPS: kernel: proc: add CPU option reporting
MIPS: kernel: proc: use seq_puts instead of seq_printf
MIPS: kernel: proc: fix trivial style errors
MIPS: Fix assembly error from MIPSr2 code used within MIPS_ISA_ARCH_LEVEL
MIPS: octeon: Remove unused functions
MIPS: Loongson64: Add of_node_put() before break
bcm47xx: Replace printk(KERN_ALERT ... pci_devname(dev)) with pci_alert()
bcm47xx: Get rid of redundant 'else'
MIPS: sni: Fix the build
MIPS: Avoid macro redefinitions
MIPS: loongson64: Fix no screen display during boot-up
MIPS: loongson64: make CPU_LOONGSON64 depends on MIPS_FP_SUPPORT
Properly document why changing PCI Class Code for GT64111 device to Host
Bridge is required as important details were after 20 years forgotten.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Replace printk(KERN_ALERT ... pci_devname(dev)) with pci_alert() which
provides PCI device name in a unified way.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
In the snipped like
if (...)
return ...;
else
the 'else' is redundant. Get rid of it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
