This macro can be used by other component so move it to a common header,
but in a slightly different way: define two macros, one macro with an
offset and the other doesn't.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Use acpi_bus_attach_private_data() to attach private data
instead of acpi_attach_data().
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When the thermal module is to be removed, we should destroy the wq
acpi_thermal_pm_queue after the ACPI driver's remove callback is
executed as we will need to flush the workqueue there, or a NULL pointer
access will be hit.
Reported-and-tested-by: Kui Zhang <kuizhang@gmail.com>
References: http://www.spinics.net/lists/kernel/msg1747251.html
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
A debug statement in acpi_thermal_trips_update() uses a wrong trip
point (tz->trips.critical instead of tz->trips.hot) to get the
temperature value from. Fix that.
Signed-off-by: Zhihui Zhang <zzhsuny@gmail.com>
[rjw: Subject and changelog]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
On resume we do not need to wait for acpi_thermal_check to finish.
Instead, we can run it asynchronously and not block the whole system
resume. Also, we make sure when we are suspending again, previously
queued work for acpi_thermal_check is done.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The ACPI thermal driver defines acpi_thermal_resume() when
CONFIG_PM_SLEEP is defined. This results in the following compile
error when CONFIG_PM_SLEEP is undefined.
CC drivers/acpi/thermal.o
drivers/acpi/thermal.c:107:8: error: ‘acpi_thermal_resume’ undeclared here (not in a function)
make[2]: *** [drivers/acpi/thermal.o] Error 1
Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* acpi-gpe:
ACPI / EC: disable GPE before removing GPE handler
ACPI / Button: Fix enabling button GPEs twice
* acpi-video:
ACPI: Blacklist Win8 OSI for some HP laptop 2013 models
ACPI / video: Fix typo in video_detect.c
* acpi-thermal:
ACPI / thermal: remove const from thermal_zone_device_ops declaration
* acpi-processor:
ACPI / scan: bail out early if failed to parse APIC ID for CPU
* acpi-sleep:
ACPI / sleep: remove panic in case hardware has changed after S4
The following commit introduced the requirement to not declare
thermal_zone_device_ops structs as const in order to allow
changing the .get_temp callback.
commit 4e5e4705bf
Author: Eduardo Valentin <eduardo.valentin@ti.com>
Date: Wed Jul 3 15:35:39 2013 -0400
thermal: introduce device tree parser
Modify acpi_thermal_zone_ops to follow the new requirement.
Signed-off-by: Emil Goode <emilgoode@gmail.com>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
[rjw: Changelog]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Replace direct inclusions of <acpi/acpi.h>, <acpi/acpi_bus.h> and
<acpi/acpi_drivers.h>, which are incorrect, with <linux/acpi.h>
inclusions and remove some inclusions of those files that aren't
necessary.
First of all, <acpi/acpi.h>, <acpi/acpi_bus.h> and <acpi/acpi_drivers.h>
should not be included directly from any files that are built for
CONFIG_ACPI unset, because that generally leads to build warnings about
undefined symbols in !CONFIG_ACPI builds. For CONFIG_ACPI set,
<linux/acpi.h> includes those files and for CONFIG_ACPI unset it
provides stub ACPI symbols to be used in that case.
Second, there are ordering dependencies between those files that always
have to be met. Namely, it is required that <acpi/acpi_bus.h> be included
prior to <acpi/acpi_drivers.h> so that the acpi_pci_root declarations the
latter depends on are always there. And <acpi/acpi.h> which provides
basic ACPICA type declarations should always be included prior to any other
ACPI headers in CONFIG_ACPI builds. That also is taken care of including
<linux/acpi.h> as appropriate.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com> (drivers/pci stuff)
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> (Xen stuff)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull thermal management updates from Zhang Rui:
"This time we only have a few changes as there are no soc thermal
changes from Eduardo. The only big change is the introduction of
TMON, a tool to help visualize, tune, and test the thermal subsystem.
The rest is mostly cleanups and fixes all over.
Specifics:
- introduce TMON, a tool base on thermal sysfs I/F. It can be used
to visualize, tune and test the thermal subsystem.
- fix a zone/cooling device binding problem, when both thermal zone
bind parameters and .bind() callback are available"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
tools/thermal: Introduce tmon, a tool for thermal subsystem
thermal: Fix binding problem when there is thermal zone params
thermal: cpu_cooling: fix return value check in cpufreq_cooling_register()
Thermal: Check for validity before doing kfree
thermal/intel_powerclamp: Add newer CPU models
Thermal: Tidy up error handling in powerclamp_init
thermal: Kconfig: cosmetic fixes
ACPI/thermal : Remove zone disabled warning
typo in drivers/thermal/Kconfig: lpatform instead of platform
Convert printks to pr_* format. Additionally re-use PREFIX constant instead of
hardcoded strings.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Once thermal zone is disabled to move thermal control to user space,
too many warnings printed in logs. Remove pr_warn from this path,
instead warn when user mode issues request to disable thermal zone.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
* acpi-assorted:
ACPI / EC: Add ASUSTEK L4R to quirk list in order to validate ECDT
ACPI / thermal: Add check of "_TZD" availability and evaluating result
Some machines don't provide _TZD, so check the availability of it
before carrying out futher operations.
If _TZD is present, also check the result of its evaluation.
[rjw: Changelog]
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
It's unreadable to pass "-1" as trip parameter directly to
thermal_zone_bind_cooling_device(). Use THERMAL_TRIPS_NONE instead.
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Acked-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The ACPI_THERMAL_FILE* macros are not used now, so remove them.
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Acked-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The acpi_thermal->lock now just is initialized when a thermal zone
device is added and destroyed when the thermal zone is removed.
It is never used in any other places, so remove it.
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Acked-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
It is quite some time that this one has been deprecated.
Get rid of it.
Should some really important user be overseen, it may be reverted and
the userspace program worked on first, but it is time to do something
to get rid of this old stuff...
Signed-off-by: Thomas Renninger <trenn@suse.de>
Acked-by: Matthew Garrett <matthew.garrett@nebula.com>
Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Introduce helper function acpi_execute_simple_method() and use it in
a number of places to simplify code.
[rjw: Changelog]
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit 4ae46be "Thermal: Introduce thermal_zone_trip_update()"
introduced a regression causing the fan to be always on even when
the system is idle.
My original idea in that commit is that:
- when the current temperature is above the trip point,
keep the fan on, even if the temperature is dropping.
- when the current temperature is below the trip point,
turn on the fan when the temperature is raising,
turn off the fan when the temperature is dropping.
But this is what the code actually does:
- when the current temperature is above the trip point,
the fan keeps on.
- when the current temperature is below the trip point,
the fan is always on because thermal_get_trend()
in driver/acpi/thermal.c returns THERMAL_TREND_RAISING.
Thus the fan keeps running even if the system is idle.
Fix this in drivers/acpi/thermal.c.
[rjw: Changelog]
References: https://bugzilla.kernel.org/show_bug.cgi?id=56591
References: https://bugzilla.kernel.org/show_bug.cgi?id=56601
References: https://bugzilla.kernel.org/show_bug.cgi?id=50041#c45
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Tested-by: Matthias <morpheusxyz123@yahoo.de>
Tested-by: Ville Syrjälä <syrjala@sci.fi>
Cc: 3.7+ <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The second argument of ACPI driver .remove() operation is only used
by the ACPI processor driver and the value passed to that driver
through it is always available from the given struct acpi_device
object's removal_type field. For this reason, the second ACPI driver
.remove() argument is in fact useless, so drop it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Jiang Liu <jiang.liu@huawei.com>
Acked-by: Toshi Kani <toshi.kani@hp.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
As per documentation, "mode" sysfs interface should be able to
enable/disable thermal processing in the kernel, so that user space
is able to take more control.
Currently, ACPI thermal driver is not following this setting, so
modify it to match the interface documentation.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPI_EXCEPTION() already appends a newline, so there is no
need for the thermal trip point message to include one too.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull thermal management update from Zhang Rui:
"Highlights:
- Introduction of thermal policy support, together with three new
thermal governors, including step_wise, user_space, fire_share.
- Introduction of ST-Ericsson db8500_thermal driver and ST-Ericsson
db8500_cpufreq_cooling driver.
- Thermal Kconfig file and Makefile refactor.
- Fixes for generic thermal layer, generic cpucooling, rcar thermal
driver and Exynos thermal driver."
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: (36 commits)
Thermal: Fix DEFAULT_THERMAL_GOVERNOR
Thermal: fix a NULL pointer dereference when generic thermal layer is built as a module
thermal: rcar: add rcar_zone_to_priv() macro
thermal: rcar: fixup the unit of temperature
thermal: cpu cooling: allow module builds
thermal: cpu cooling: use const parameter while registering
Thermal: Add ST-Ericsson DB8500 thermal properties and platform data.
Thermal: Add ST-Ericsson DB8500 thermal driver.
drivers/thermal/Makefile refactor
Exynos: Add missing dependency
Refactor drivers/thermal/Kconfig
thermal: cpu_cooling: Make 'notify_device' static
Thermal: Remove the cooling_cpufreq_list.
Thermal: fix bug of counting cpu frequencies.
Thermal: add indent for code alignment.
thermal: rcar_thermal: remove explicitly used devm_kfree/iounap()
thermal: user_space: Add missing static storage class specifiers
thermal: fair_share: Add missing static storage class specifiers
thermal: step_wise: Add missing static storage class specifiers
Thermal: Fix oops and unlocking in thermal_sys.c
...
On some platforms, _TMP and _CRT/_HOT/_PSV/_ACx have dependency.
And there is no way for OS to detect this dependency.
commit 9bcb811896 shows us a problem
that _TMP must be evaluate after _CRT/_HOT/_PSV/_ACx, or else
firmware will shutdown the system.
But the machine in https://bugzilla.kernel.org/show_bug.cgi?id=43284
shows us that _PSV would return valid value only if _TMP has been
evaluated once.
With this patch, all of the control methods will be evaluated once,
in the _CRT/_HOT/_PSV/_CRT/_TMP order, before they are actually used.
[rjw: Added a local variable for the handle and modified the loop
slightly.]
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Tested-by: katabami <katabami@lavabit.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch adds the thermal zone parameter as an argument to
the tzd_register() function call; and updates other drivers
using this function.
Signed-off-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Conflicts:
drivers/staging/omap-thermal/omap-thermal-common.
OMAP supplied dummy TC1 and TC2,
at the same time that the thermal tree removed them
from thermal_zone_device_register()
drivers/thermal/cpu_cooling.c b/drivers/thermal/cpu_cooling.c
propogate the upstream MAX_IDR_LEVEL re-name
to prevent a build failure
Previously-fixed-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Len Brown <len.brown@intel.com>
This function is used to update the cooling state of
all the cooling devices that are bound to an active trip point.
This will be used for passive cooling as well, in the future patches.
as both active and passive cooling can share the same algorithm,
which is
1. if the temperature is higher than a trip point,
a. if the trend is THERMAL_TREND_RAISING, use higher cooling
state for this trip point
b. if the trend is THERMAL_TREND_DROPPING, use lower cooling
state for this trip point
2. if the temperature is lower than a trip point, use lower
cooling state for this trip point.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Reviewed-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Eduardo Valentin <eduardo.valentin@ti.com>
Remove tc1/tc2 in generic thermal layer.
.get_trend() callback starts to take effect from this patch.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Reviewed-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Valentin, Eduardo <eduardo.valentin@ti.com>
According to ACPI spec, tc1 and tc2 are used by OSPM
to anticipate the temperature trends.
We introduced the same concept to the generic thermal layer
for passive cooling, but now it seems that these values
are hard to be used on other platforms.
So We introduce .get_trend() as a more general solution.
For the platform thermal drivers that have their own way to
anticipate the temperature trends, they should provide
their own .get_trend() callback.
Or else, we will calculate the temperature trends by simply
comparing the current temperature and the cached previous
temperature reading.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Reviewed-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Valentin, Eduardo <eduardo.valentin@ti.com>
set upper and lower limits when binding
a thermal cooling device to a thermal zone device.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Reviewed-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Eduardo Valentin <eduardo.valentin@ti.com>
According to compiler warnings, several suspend/resume functions
in ACPI drivers are not used for CONFIG_PM_SLEEP unset, so add
#ifdefs to prevent them from being built in that case.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Pull ACPI & power management update from Len Brown:
"Re-write of the turbostat tool.
lower overhead was necessary for measuring very large system when
they are very idle.
IVB support in intel_idle
It's what I run on my IVB, others should be able to also:-)
ACPICA core update
We have found some bugs due to divergence between Linux and the
upstream ACPICA base. Most of these patches are to reduce that
divergence to reduce the risk of future bugs.
Some cpuidle updates, mostly for non-Intel
More will be coming, as they depend on this part.
Some thermal management changes needed by non-ACPI systems.
Some _OST (OS Status Indication) updates for hot ACPI hot-plug."
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux: (51 commits)
Thermal: Documentation update
Thermal: Add Hysteresis attributes
Thermal: Make Thermal trip points writeable
ACPI/AC: prevent OOPS on some boxes due to missing check power_supply_register() return value check
tools/power: turbostat: fix large c1% issue
tools/power: turbostat v2 - re-write for efficiency
ACPICA: Update to version 20120711
ACPICA: AcpiSrc: Fix some translation issues for Linux conversion
ACPICA: Update header files copyrights to 2012
ACPICA: Add new ACPI table load/unload external interfaces
ACPICA: Split file: tbxface.c -> tbxfload.c
ACPICA: Add PCC address space to space ID decode function
ACPICA: Fix some comment fields
ACPICA: Table manager: deploy new firmware error/warning interfaces
ACPICA: Add new interfaces for BIOS(firmware) errors and warnings
ACPICA: Split exception code utilities to a new file, utexcep.c
ACPI: acpi_pad: tune round_robin_time
ACPICA: Update to version 20120620
ACPICA: Add support for implicit notify on multiple devices
ACPICA: Update comments; no functional change
...
With commit 6503e5df08,
the value of /sys/class/thermal/thermal_zoneX/mode has been changed
from user/kernel to enabled/disabled.
Update the documentation so that users won't be confused.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Some of the thermal drivers using the Generic Thermal Framework
require (all/some) trip points to be writeable. This patch makes
the trip point temperatures writeable on a per-trip point basis,
and modifies the required function call in thermal.c. This patch
also updates the Documentation to reflect the new change.
Signed-off-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Make the ACPI thermal driver define its PM callbacks through
a struct dev_pm_ops object rather than by using legacy PM hooks
in struct acpi_device_ops.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
An HP laptop (Pavilion G4-1016tx) has the following code in _TMP:
Store (\_SB.PCI0.LPCB.EC0.RTMP, Local0)
If (LGreaterEqual (Local0, S4TP))
{
Store (One, HTS4)
}
S4TP is initialised at 0 and not programmed further until either _HOT or
_CRT is called. If we evaluate _TMP before the trip points then HTS4 will
always be set, causing the firmware to generate a message on boot
complaining that the system shut down because of overheating. The simplest
solution is just to reverse the checking of trip points and _TMP in thermal
init.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Structs battery_file, acpi_dock_ops, file_operations,
thermal_cooling_device_ops, thermal_zone_device_ops, kernel_param_ops
are not changed in runtime. It is safe to make them const.
register_hotplug_dock_device() was altered to take const "ops" argument
to respect acpi_dock_ops' const notion.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Use the new function acpi_bus_update_power() for manipulating power
resources used by ACPI fan devices, which allows them to be put into
the right state during initialization and resume. Consequently,
remove the flags.force_power_state field from struct acpi_device,
which is not necessary any more.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
Remove the deprecated ACPI thermal driver procfs I/F,
as stated in the changelog of commit 43d9f87b79
sysfs I/F is available at /sys/class/thermal/thermal_zoneX/
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Mark the ACPI thermal procfs I/F deprecated, because /sys/class/thermal/
is already available and has been working for years w/o any problem.
The ACPI thermal procfs I/F will be removed in 2.6.37.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
V2: Corrected integer/long conversion.
Some BIOSes return a negative value for the critical trip point.
Especially since Windows 2006...
We currently invalidate the whole thermal zone in this case.
But it may still be needed for cooling, also without critical
trip point.
This patch invalidates the critical trip point if no _CRT
function is found or if it returns negative values, but does
not invalidate the whole thermal zone in this case.
Reference: http://bugzilla.novell.com/show_bug.cgi?id=531547
Signed-off-by: Thomas Renninger <trenn@suse.de>
Tested-by: clarkt@cnsp.com
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
ACPI spec says (11.5 Thermal Zone Interface Requirements):
A thermal zone must contain at least one trip point
(critical, near critical, active, or passive)
Check this once at init time.
Signed-off-by: Thomas Renninger <trenn@suse.de>
Tested-by: clarkt@cnsp.com
Signed-off-by: Len Brown <len.brown@intel.com>
Users can force a passive trip point for a thermal zone that does not
have _PSV defined in ACPI by setting the passive attribute in sysfs.
It's useful to display such trip points in /proc/acpi/thermal_zone.
.../TZ1/cooling_mode:<setting not supported>
.../TZ1/polling_frequency:polling frequency: 10 seconds
.../TZ1/state:state: ok
.../TZ1/temperature:temperature: 53 C
.../TZ1/trip_points:critical (S5): 110 C
.../TZ1/trip_points:passive (forced): 95 C
And if not set (passive is 0):
.../TZ1/trip_points:passive (forced):<not set>
Signed-off-by: Frans Pop <elendil@planet.nl>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Linux/ACPI core files using internal.h all PREFIX "ACPI: ",
however, not all ACPI drivers use/want it -- and they
should not have to #undef PREFIX to define their own.
Add GPL commment to internal.h while we are there.
This does not change any actual console output,
asside from a whitespace fix.
Signed-off-by: Len Brown <len.brown@intel.com>
