If we do not have a firmare script for a given transfer,
the setup of this channel must fail. For this the script
addresses have to be < 0 initially, not 0.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
channel0 of the sdma engine is the configuration channel. It
is a shared resource and thus must be protected by a mutex.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Making dmatest threads freezable allows its use for system PM testing.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
At least, on SPEAr platforms there is one peripheral, JPEG, which can be flow
controller for DMA transfer. Currently DMA controller driver didn't support
peripheral flow controller configurations.
This patch adds device_fc field in struct pl08x_channel_data, which will be used
only for slave transfers and is not used in case of mem2mem transfers.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When we have DMA transfers between peripheral and memory, then we shouldn't
reduce width of peripheral at all, as that may be a strict requirement. But we
can always reduce width of memory access, with some compromise in performance.
Thus, we must select peripheral as master and not memory.
Also this rearranges code to make it shorter.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Currently lli_len is aligned to min of two widths, which looks to be incorrect.
Instead it should be aligned to max of both widths.
Lets say, total_size = 441 bytes
MIN: lets check if min() suits or not:
CASE 1: srcwidth = 1, dstwidth = 4
min(src, dst) = 1
i.e. We program transfer size in control reg to 441.
Now, till 440 bytes everything is fine, but on the last byte DMAC can't transfer
1 byte to dst, as its width is 4.
CASE 2: srcwidth = 4, dstwidth = 1
min(src, dst) = 1
i.e. we program transfer size in control reg to 110 (data transferred = 110 * srcwidth).
So, here too 1 byte is left, but on the source side.
MAX: Lets check if max() suits or not:
CASE 3: srcwidth = 1, dstwidth = 4
max(src, dst) = 4
Aligned size is 440
i.e. We program transfer size in control reg to 440.
Now, all 440 bytes will be transferred without any issues.
CASE 4: srcwidth = 4, dstwidth = 1
max(src, dst) = 4
Aligned size is 440
i.e. We program transfer size in control reg to 110 (data transferred = 110 * srcwidth).
Now, also all 440 bytes will be transferred without any issues.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Code for creating single byte llis is present at several places. Create a
routine to avoid code redundancy.
Also, we don't need one lli per single byte transfer, we can have single lli to
do all single byte transfer.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
max_bytes_per_lli = bd.srcbus.buswidth * PL080_CONTROL_TRANSFER_SIZE_MASK;
This is confirmed by ARM support guys.
Below is summary of mail exchange with them:
[Viresh] What is the total data to be transferred in case source and destination
bus widths are different. Suppose, source bus width is 2 bytes and destination
is 4 bytes. Now in order to transfer 80 bytes, what should be value of
TransferSize field in control reg: 40? or 20?.
[David from ARM] The value that is programmed into the TransferSize field should
be the number of <SourceWidth> transfers needed to achieve the required data
transfer.
So, to transfer 80 bytes, with a Source Width of 2, the TransferSize field =
should be programmed with:
Total transfer size
------------------- = 40
<source width>
[Viresh] Will this change if source is 4 bytes and dest is 2?
[David] Yes - the calculation then becomes:
Total transfer size
------------------- =20
<source width>
Also, max_bytes_per_lli must be calculated after fixing src and dest widths not
before that. So move this code to the correct place.
This patch also removes max_bytes_per_lli from earlier print message, as till
that point max_bytes_per_lli is unknown.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Pl080 Manual says: "Bursts do not cross the 1KB address boundary"
We can program the controller to cross 1 KB boundary on a burst and controller
can take care of this boundary condition by itself.
Following is the discussion with ARM Technical Support Guys (David):
[Viresh] Manual says: "Bursts do not cross the 1KB address boundary"
What does that actually mean? As, Maximum size transferable with a single LLI is
4095 * 4 =16380 ~ 16KB. So, if we don't have src/dest address aligned to burst
size, we can't use this big of an LLI.
[David] There is a difference between bursts describing the total data
transferred by the DMA controller and AHB bursts. Bursts described by the
programmable parameters in the PL080 have no direct connection with the bursts
that are seen on the AHB bus.
The statement that "Bursts do not cross the 1KB address boundary" in the TRM is
referring to AHB bursts, where this limitation is a requirement of the AHB spec.
You can still issue bursts within the PL080 that are in excess of 1KB. The
PL080 will make sure that its bursts are broken down into legal AHB bursts which
will be formatted to ensure that no AHB burst crosses a 1KB boundary.
Based on above discussion, this patch removes all code related to 1 KB boundary
as we are not required to handle this in driver.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Currently, if error interrupt occurs, nothing is done in interrupt handler (just
clearing the interrupts). We must somehow indicate this to the user that DMA is
over, due to ERR interrupt or TC interrupt.
So, this patch just schedules existing tasklet, with a print showing error
interrupt has occurred on which channels.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
We have just executed following in pl08x_get_phy_channel():
ch->signal = -1;
We don't have to compare "ch->signal < 0", as this will always be true.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Simply writing 1 on bit 0 is sufficient instead of reading and clearing bits.
Also as per manual, for bit 3-31 of DMACConfiguration register:
"read undefined, write as 0"
So, we must not rely on values read from this registers bit 3-31.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Insert notifiers for the runtime PM API. With this the runtime PM layer kicks in
to action where used.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
For 8 memory and 16 slave channels 35 boot print lines are printed. And that is
too much. Most of this would be more useful for debugging. So moving few of them
to dev_dbg instead of dev_info. Now only 3 prints will be printed.
This also rearrange one of the debug message to fit into two lines.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Similar comment is present over routine also pl08x_choose_master_bus(). Keeping
one of them. Also rewrite that comment to convey message clearly.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
As mentioned in Documentation/CodingStyle,
The preferred form for passing a size of a struct is the following:
p = kmalloc(sizeof(*p), ...);
The alternative form where struct name is spelled out hurts readability and
introduces an opportunity for a bug when the pointer variable type is changed
but the corresponding sizeof that is passed to a memory allocator is not.
This patch replaces (struct xyz) with *ptr at several occurrences in driver.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Header files included in driver are not present in alphabetical order. Rearrange
them in alphabetical order.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
There were few formatting related issues in code. This patch fixes them.
Fixes include:
- Remove extra blank lines
- align code to 80 cols
- combine several lines to one line
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In this driver, we can trigger cyclic transfer on peripherals-DMA interfaces.
It is dependent on driver implementation but cannot depend on a platform
property: we remove the dma_has_cap(DMA_CYCLIC, ) test which has no meaning.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Cyclic property and paused state are encoded as bits in the channel status
bitfield. Tests of those bits are wrapped in convenient helper functions.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Save/restore dma controller state across a suspend-resume sequence.
The prepare() function will wait for the non-cyclic channels to become idle.
It also deals with cyclic operations with the start at next period while
resuming.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
dmaengine routines can be called from interrupt context and with
interrupts disabled. Whereas spin_unlock_bh can't be called from
such contexts. So this patch converts all spin_lock* routines
to irqsave variants.
Also, spin_lock() used in tasklet is converted to irqsave variants,
as tasklet can be interrupted, and dma requests from such interruptions
may also call spin_lock.
Idea from dw_dmac patch by Viresh Kumar.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
After calling mxs_dma_disable_chan() for a channel, that channel
becomes unusable because some controller registers can only be written
when the clock is enabled via CLKGATE.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
* 'fixes' of master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: drop experimental status for ARM_PATCH_PHYS_VIRT
ARM: 7008/1: alignment: Make SIGBUS sent to userspace POSIXly correct
ARM: 7007/1: alignment: Prevent ignoring of faults with ARMv6 unaligned access model
ARM: 7010/1: mm: fix invalid loop for poison_init_mem
ARM: 7005/1: freshen up mm/proc-arm946.S
dmaengine: PL08x: Fix trivial build error
ARM: Fix build error for SMP=n builds
Something changed during the 3.1 merge window in the include files
which now causes the pl08x DMA engine driver to fail to build. Fix
this by adding the now necessary dma-mapping.h include:
drivers/dma/amba-pl08x.c: In function ■pl08x_unmap_buffers■:
drivers/dma/amba-pl08x.c:1524: error: implicit declaration of function ■dma_unmap_single■
drivers/dma/amba-pl08x.c:1527: error: implicit declaration of function ■dma_unmap_page■
Acked-by: Vinod Koul <vinod.koul@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In case, some error occurs while doing memcpy transfers, we must terminate all
transfers physically too. This is achieved by calling device_control() routine
with TERMINATE_ALL as parameter.
This is also required to be done in case module is removed while we are in
middle of some transfers.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx:
dmaengine: use DEFINE_IDR for static initialization
ioat: fix xor_idx_to_desc
Avoid section type conflict in dma/ioat/dma_v3.c
ioat: Adding PCI IDs for IOAT devices on SandyBridge platforms
We could use DEFINE_IDR for statically allocated idr
that allow us to save a few lines of code.
And also remove unneeded mutex_init() for dma_list_mutex, as
dma_list_mutex is initialized automatically by DEFINE_MUTEX().
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
For versions of the device that implement operation-types 0x87, 0x88
(IOAT_OP_XOR, IOAT_OP_XOR_VAL) this map determines whether a given
source is located in the base or extended descriptor. Source addresses
6 through 8 require an extended descriptor, hence 0xe0, not 0xd0. No
shipping hardware currently implements these operation types.
Reported-by: Evgueni Smogailov <evgueni.smogailov@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
It does not need to allocate space and copy fw_name in function
sdma_get_firmware().
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Vinod Koul <vinod.koul@intel.com>
It might be not good to use software defined version to identify sdma
device type, when hardware does not define such version. Instead,
soc name is stable enough to define the device type.
The patch uses platform_device_id rather than version number passed
by platform data to identify sdma device type/version.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Vinod Koul <vinod.koul@intel.com>
pl08x_width function does not handle rest of enums for DMA_SLAVE_BUSWIDTH_xxxx
which causes gcc to emit below warining
drivers/dma/amba-pl08x.c: In function 'pl08x_width':
drivers/dma/amba-pl08x.c:1119: warning: enumeration value
'DMA_SLAVE_BUSWIDTH_UNDEFINED' not handled in switch
drivers/dma/amba-pl08x.c:1119: warning: enumeration value
'DMA_SLAVE_BUSWIDTH_8_BYTES' not handled in switch
this patch adds a default case which returns error
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Now that we have separate cctl values for M>P and P>M transfers, we can
avoid calculating the cctl value each time we prepare a transaction.
Move the bus selection and increment setting to the slave configuration
and initialization functions.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Store the source/destination cctl values into the channel structure.
This moves us towards being able to avoid a configuration call each
time we use the channel.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Store the source/destination slave address separately into the channel
structure. This moves us towards being able to avoid a configuration
call each time we use the channel.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Clean up debugging when setting up the LLI list. This reduces the
amount of output while preserving the information, and makes it easier
to read.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Avoid re-selecting the LLI bus each time we create an LLI. Move it out
of the LLI setup loops.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
PL08X_WQ_PERIODMIN and PL08X_MAX_ALLOCS are not used, remove them.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
We met some channels in abnormal state after disable.
Reset it to get a clean state.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Call pci_set_drvdata() once in intel_mid_dma_probe() is enough.
Remove redundant pci_set_drvdata() calls in dma_suspend() and dma_resume().
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The pl330 needs platform data for describing peripheral connections, but
some platforms may only support memory to memory dma channels. In this
case, we can probe for how many channels there are and don't need the
platform data.
As memcpy requests don't need channel private data to hold peripheral
info, allow private data to be NULL in this case.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Jassi Brar <jassisinghbrar@gmail.com>
Cc: Vinod Koul <vkoul@infradead.org>
Cc: Dan Williams <dan.j.williams@intel.com>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (43 commits)
fs: Merge split strings
treewide: fix potentially dangerous trailing ';' in #defined values/expressions
uwb: Fix misspelling of neighbourhood in comment
net, netfilter: Remove redundant goto in ebt_ulog_packet
trivial: don't touch files that are removed in the staging tree
lib/vsprintf: replace link to Draft by final RFC number
doc: Kconfig: `to be' -> `be'
doc: Kconfig: Typo: square -> squared
doc: Konfig: Documentation/power/{pm => apm-acpi}.txt
drivers/net: static should be at beginning of declaration
drivers/media: static should be at beginning of declaration
drivers/i2c: static should be at beginning of declaration
XTENSA: static should be at beginning of declaration
SH: static should be at beginning of declaration
MIPS: static should be at beginning of declaration
ARM: static should be at beginning of declaration
rcu: treewide: Do not use rcu_read_lock_held when calling rcu_dereference_check
Update my e-mail address
PCIe ASPM: forcedly -> forcibly
gma500: push through device driver tree
...
Fix up trivial conflicts:
- arch/arm/mach-ep93xx/dma-m2p.c (deleted)
- drivers/gpio/gpio-ep93xx.c (renamed and context nearby)
- drivers/net/r8169.c (just context changes)
* 'next/fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc: (35 commits)
ARM: msm: platsmp: determine number of CPU cores at boot time
ARM: Tegra: Seaboard: Fix I2C bus numbering for ADT7461
ARM: Tegra: Trimslice: Tri-state DAP3 pinmux
ARM: orion5x: fixup 5181 MPP mask check
ARM: mxs-dma: include <linux/dmaengine.h>
ARM: i.MX53: consistently use MX53_UART_PAD_CTRL for uart txd/rxd/rts/cts
ARM: i.MX53: UARTn_CTS pin should not change RTS input select
ARM: i.MX53: UARTn_TXD pin should not change RXD input select
ARM: mx25: Fix typo on CAN1_RX pad setting
iomux-mx53: add missing 'IOMUX_CONFIG_SION' for some I2C pad definitions
ARM: NUC93X: add UL suffix to VMALLOC_END to ensure it is properly typed
ARM: LPC32XXX: add UL suffix to VMALLOC_END to ensure it is properly typed
ARM: CNS3XXX: add UL suffix to VMALLOC_END to ensure it is properly typed
ARM: i.MX53: Fix IOMUX type o's
ARM i.MX dma: Fix burstsize settings
mach-mx5: fix the I2C clock parents
ARM: mxs/tx28: according to the TX28's datasheet D4-D7 are not used for MMC0
ARM i.MX23/28: platform-mxsfb: Add missing include of linux/dma-mapping.h
ARM: mx53: Fix some interrupts marked as reserved.
MXC: iomux-v3: correct NO_PAD_CTRL definition
...
Fix up trivial conflict in arch/arm/mach-imx/mach-mx31_3ds.c
Currently, Mode-Control register is accessed by read-modify-write.
According to DMA hardware specifications datasheet, prohibits this method.
Because this register resets to 0 by DMA HW after DMA transfer completes.
Thus, current read-modify-write processing can cause unexpected behavior.
The datasheet says in case of writing Mode-Control register, set the value for only target channel, the others must set '11b'.
e.g. Set DMA0=01b DMA11=10b
CTL0=33333331h
CTL2=00002333h
NOTE:
CTL0 includes DMA0~7 Mode-Control register.
CTL2 includes DMA8~11 Mode-Control register.
This patch modifies the issue.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
* 'spi/next' of git://git.secretlab.ca/git/linux-2.6: (34 commits)
spi/imx: add device tree probe support
spi/imx: copy gpio number passed by platform data into driver private data
spi/imx: use soc name in spi device type naming scheme
spi/imx: merge type SPI_IMX_VER_0_7 into SPI_IMX_VER_0_4
spi/imx: do not use spi_imx2_3 to name SPI_IMX_VER_2_3 function and macro
spi/imx: use mx21 to name SPI_IMX_VER_0_0 function and macro
spi/imx: do not make copy of spi_imx_devtype_data
spi/dw: Add spi number into spi irq desc
spi/tegra: Use engineering names in DT compatible property
spi/fsl_spi: fix CPM spi driver
mach-s3c2410: remove unused spi-gpio.h file
spi: remove obsolete spi-s3c24xx-gpio driver
mach-gta2: remove unused spi-gpio.h include
mach-qt2410: convert to spi_gpio
mach-jive: convert to spi_gpio
spi/pxa2xx: Remove unavailable ssp_type from documentation
spi/bfin_spi: uninline fat queue funcs
spi/bfin_spi: constify pin array
spi/bfin_spi: use structs for accessing hardware regs
spi/topcliff-pch: Support new device ML7223 IOH
...
Fix up trivial conflict in arch/arm/mach-ep93xx/Makefile
const __read_mostly is not legal and causes section type conflicts.
That's because the read.mostly section is not read only.
Simply drop the __read_mostly designation.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
[drop __read_mostly instead of const]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Adding to pci_id.h and the device table for ioat.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
In general, the mxs-dma users get separate irq for each channel,
but gpmi is special one which has only one irq shared by all gpmi
channels. It causes mxs_dma channel allocation function fail for
all other gpmi channels except the first one calling into the
function.
The patch gets request_irq call skipped for NO_IRQ case, and leaves
this gpmi specific quirk to gpmi driver to sort out. It will fix
above problem if gpmi driver sets chan_irq as gpmi irq for only one
channel and NO_IRQ for all the rest channels.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
While testing Per Forlins MMC speed improvements I noticed a
semantic bug in the COH901318 driver: it will write to channel
registers in the prep_slave_sg() function, instead of deferring
it to later, breaking the assumption from the drivers to be able
to queue up new jobs while another job is running. Fix this by
storing up the initial register writes in the job descriptors
and write them to hardware when we process the descriptor
instead. Now the stress tests work.
Acked-by: Per Forlin <per.forlin@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Currently the runtime config implementation forces the memory side
parameters to be the same as the peripheral side. Allow these to be
different, and check for misconfiguration.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Reviewed-by: Ulf HANSSON <ulf.hansson@stericsson.com>
Tested-by: Stefan Nilsson <stefan.xk.nilsson@stericsson.com>
Reviewed-by: Per Forlin <per.forlin@stericsson.com>
Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Robert Marklund <robert.marklund@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The DMA40 is not a PrimeCell from ARM, but it still use the same
ID registers. So let's utilize the existing macros in the
PrimeCell header to identify manufacturer and revision of the IP
block instead of reinventing the wheel.
Cc: Robert Marklund <robert.marklund@stericsson.com>
Cc: Per Forlin <per.forlin@linaro.org>
Cc: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This function may be initiated from IRQ context, so the allocation
must allocate NOWAIT memory.
Signed-off-by: Robert Marklund <robert.marklund@stericsson.com>
Reviewed-by: Rabin Vincent <rabin.vincent@stericsson.com>
Reviewed-by: Philippe Langlais <philippe.langlais@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
ste_dma40 now implements issue_pending according to documentation.
Submit adds descriptos to a pending queue with are flushed down to the DMAC
at issue_pending.
Signed-off-by: Per Forlin <per.forlin@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
tx_submit will add descriptors to the pending queue. Issue pending
will then move the pending descriptors to the transfer queue.
Signed-off-by: Per Forlin <per.forlin@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
It is not good to have cpu_name and to_version encoded into sdma
firmware name as variables. For example, there are three TOs of
imx51 soc, the sdma script never changes since TO1, which means
all three TOs of imx51 uses TO1 version of sdma script. But we
have to prepare three identical firmwares, sdma-imx51-to1.bin
sdma-imx51-to2.bin and sdma-imx51-to3.bin, to have the kernel
capable of running on all three TOs.
The patch removes cpu_name and to_version from sdma platform data,
and instead uses fw_name to pass the firmware name, so that we can
pass the TO version where it's relevant and skip it where only one
firmware exists.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
dmaengine expects the maxburst parameter in words, not bytes.
The imxdma driver and its users do this wrong. Fix this.
As a side note the imx-pcm-dma-mx2 driver was 'fixed' to work
with imx-dma. This broke the driver with imx-sdma support which
correctly takes the maxburst parameter in words. This patch
puts the sdma based sound back to work.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
There exist systems with multiple DMA controllers with different
capabilities. For example, on some sh-mobile / rmobile systems there are
DMA controllers, whose channels can be configured to be used with
SD- and MMC-host controllers, serial ports etc. Besides there are also
DMA controllers, that can only be used for one special function, e.g.,
for USB. In such cases the DMA client filter function can just choose
to specify to the DMA driver, which channel it needs. Then the
.device_alloc_chan_resources() method of the DMA driver will check,
whether it can provide that dunction. If not, it will fail and the loop
in __dma_request_channel() will continue to the next DMA device, until
it finds a suitable one. This works fine with just one minor glitch:
the kernel logs error messages like
dmaengine: failed to get <channel name>: (-<error code>)
after each such non-critical failure. This patch lowers priority of
this message to the debug level.
Reported-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Remove linux/mm.h inclusion from netdevice.h -- it's unused (I've checked manually).
To prevent mm.h inclusion via other channels also extract "enum dma_data_direction"
definition into separate header. This tiny piece is what gluing netdevice.h with mm.h
via "netdevice.h => dmaengine.h => dma-mapping.h => scatterlist.h => mm.h".
Removal of mm.h from scatterlist.h was tried and was found not feasible
on most archs, so the link was cutoff earlier.
Hope people are OK with tiny include file.
Note, that mm_types.h is still dragged in, but it is a separate story.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IE bit position on CHCR register is not same in all DMAC.
This patch adds new "chcr_ie_bit" to decide it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
CHCR register position is not same in all DMAC.
This patch adds new "chcr_offset" to decide it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
chan_pdata->dmars_bit is unsigned int
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
It is not readable that there is any spin_unlock_bh on same function.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds "to_sh_dev" macro, and clean up codes.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The symbol 'ep93xx_dma_prep_dma_memcpy' is only used in this driver
and should be marked static.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Mika Westerberg <mika.westerberg@iki.fi>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@iki.fi>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Fix the recently added SH_DMAC_MAX_CHANNELS handling code in
300e5f9 dmaengine: shdma: Fix SH_DMAC_MAX_CHANNELS handling
Without this fix the shdma driver outputs silly messages in
case SH_DMAC_MAX_CHANNELS happens to match the platform data:
sh-dma-engine sh-dma-engine.0: Attempting to register 20 DMA channels when a max
imum of 20 are supported.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Several fixes as well where the +1 was missing.
Done via coccinelle scripts like:
@@
struct resource *ptr;
@@
- ptr->end - ptr->start + 1
+ resource_size(ptr)
and some grep and typing.
Mostly uncompiled, no cross-compilers.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The ep93xx DMA controller has 10 independent memory to peripheral (M2P)
channels, and 2 dedicated memory to memory (M2M) channels. M2M channels can
also be used by SPI and IDE to perform DMA transfers to/from their memory
mapped FIFOs.
This driver supports both M2P and M2M channels with DMA_SLAVE, DMA_CYCLIC and
DMA_MEMCPY (M2M only) capabilities.
Signed-off-by: Mika Westerberg <mika.westerberg@iki.fi>
Signed-off-by: Ryan Mallon <rmallon@gmail.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The ep93xx DMA controller has 10 independent memory to peripheral (M2P)
channels, and 2 dedicated memory to memory (M2M) channels. M2M channels can
also be used by SPI and IDE to perform DMA transfers to/from their memory
mapped FIFOs.
This driver supports both M2P and M2M channels with DMA_SLAVE, DMA_CYCLIC and
DMA_MEMCPY (M2M only) capabilities.
Signed-off-by: Mika Westerberg <mika.westerberg@iki.fi>
Signed-off-by: Ryan Mallon <rmallon@gmail.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
A recent patch has introduced a regression, where repeating a memcpy
DMA test with shdma module unloading between them skips the DMA channel
configuration. Fix this regression by always configuring the channel
during its allocation.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
ISSUE: In case PCH_DMA with I2S communications with ch8~ch11, sometimes I2S data
is not send correctly.
CAUSE: The following patch I submitted before was not enough modification for
supporting DMA ch8~ch11. The modification for status register of ch8~11 was not
enough.
pch_dma: Support I2S for ML7213 IOH
author Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Mon, 9 May 2011 07:09:38 +0000 (16:09 +0900)
committer Vinod Koul <vinod.koul@intel.com>
Mon, 9 May 2011 11:42:23 +0000 (16:42 +0530)
commit 194f5f2706
tree c9d4903ea0
parent 60092d0bde
This patch fixes the issue.
We can confirm PCH_DMA with I2S communications with ch8~ch11 works well.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx: (33 commits)
x86: poll waiting for I/OAT DMA channel status
maintainers: add dma engine tree details
dmaengine: add TODO items for future work on dma drivers
dmaengine: Add API documentation for slave dma usage
dmaengine/dw_dmac: Update maintainer-ship
dmaengine: move link order
dmaengine/dw_dmac: implement pause and resume in dwc_control
dmaengine/dw_dmac: Replace spin_lock* with irqsave variants and enable submission from callback
dmaengine/dw_dmac: Divide one sg to many desc, if sg len is greater than DWC_MAX_COUNT
dmaengine/dw_dmac: set residue as total len in dwc_tx_status if status is !DMA_SUCCESS
dmaengine/dw_dmac: don't call callback routine in case dmaengine_terminate_all() is called
dmaengine: at_hdmac: pause: no need to wait for FIFO empty
pch_dma: modify pci device table definition
pch_dma: Support new device ML7223 IOH
pch_dma: Support I2S for ML7213 IOH
pch_dma: Fix DMA setting issue
pch_dma: modify for checkpatch
pch_dma: fix dma direction issue for ML7213 IOH video-in
dmaengine: at_hdmac: use descriptor chaining help function
dmaengine: at_hdmac: implement pause and resume in atc_control
...
Fix up trivial conflict in drivers/dma/dw_dmac.c
For certain system configurations a 5 usec udelay before checking I/OAT DMA
channel status is sometimes not sufficient, resulting in a false failure
status and unnecessary freeing of channel resources. Conversely, for many
configurations 5 usec is longer than necessary.
Loop for up to 20 usec waiting for successful status before failing.
Signed-off-by: Dimitri Sivanich <sivanich@sgi.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
With the addition of a device platform mfd_cell pointer, MFD drivers
can go back to passing platform data back to their sub drivers.
This allows for an mfd_cell->mfd_data removal and thus keep the
sub drivers MFD agnostic. This is mostly needed for non MFD aware
sub drivers.
Acked-by: Richard Röjfors <richard.rojfors@pelagicore.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Nobody is currently maintaining dw_dmac. We are using dw_dmac for SPEAr13xx and
are currently maintaining it. After discussing with Vinod, sending this patch to
update maintainer-ship of dw_dmac.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Havard Skinnemoen <hskinnemoen@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Update SH_DMAC_MAX_CHANNELS to support the 20 DMA
channels included in the sh73a0 SY-DMAC hardware.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Fix the shdma.c handing of SH_DMAC_MAX_CHANNELS
to avoid overwriting the chan_irq[] and chan_flag[]
arrays in the case of pdata->channel_num is larger
than SH_DMAC_MAX_CHANNELS.
With this patch applied up to SH_DMAC_MAX_CHANNELS
will be used by the shdma.c driver. If more channels
are available in the platform data the user will
be notified on the console.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch makes the shdma.c driver allow slave operation
on DMA hardware mapped with a single I/O-memory window.
The dmae_set_dmars() function is adjusted to use the
first memory window in case of a missing DMARS window.
At probe() time the code is updated to enable DMA_SLAVE
only if slave information is passed with the platform data.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
