Initialize the PMIC voltage regulators and provide the supply map for
PCI-e clock supply. The rest of the supplies should be added together
with the drivers that use them.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
CC: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch adds the config infrastructure, the pinmux and basic
board setup code for PAZ00 (name of board inside the AC100/AZ).
Signed-off-by: Marc Dietrich <marvin24@gmx.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
This adds board support for the Seaboard eval platform and some of the
derivatives that are very similar. Since they only differ in some very
minor ways, most of the code is shared.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Colin Cross <ccross@android.com>
Add a common location to register resources for used on-chip devices
that are commonly configured on boards. Devices will be added to this file
as more drivers are added that can make use of them.
This is based on work contributed by several people, most of it from
Colin Cross and Erik Gilling.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Colin Cross <ccross@android.com>
The frequency memory bus on Tegra can be adjusted without
disabling accesses to memory by updating the memory
configuration registers from a per-board table, and then
changing the clock frequency. The clock controller and
memory controller have an interlock that prevents the
new memory registers from taking effect until the
clock frequency change.
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Cross <ccross@android.com>
The existing version did not extend well to core dvfs, drop it
for now until the new clk api with clk_prepare and clk_unprepare
is ready and non-atomic clocks are possible.
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Cross <ccross@android.com>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
CC: Olof Johansson <olof@lixom.net>
CC: Gary King <GKing@nvidia.com>
Signed-off-by: Colin Cross <ccross@android.com>
Change-Id: Ibd0bcd46895eb88952b9db29e1f68572d39aae01
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Arnd Bergmann <arnd@arndb.de>
CC: Russell King <linux@arm.linux.org.uk>
CC: Gary King <GKing@nvidia.com>
Signed-off-by: Colin Cross <ccross@android.com>
The APB DMA block handles DMA transfers to and from some peripherals
in the Tegra SOC. It reads from sequential addresses on the memory
bus, and writes repeatedly to the same address on the APB bus.
Two transfer modes are supported, oneshot for transferring a known
size to or from a peripheral, and continuous for streaming data.
In continuous mode, a callback occurs when the buffer is half full
to allow the existing data to be handled and a new request queued.x
v2 changes:
dma API no longer uses PTR_ERR
Signed-off-by: Erik Gilling <konkers@android.com>
Signed-off-by: Colin Cross <ccross@android.com>
Implement cpufreq support for the Tegra SOC. DVFS is handled by the
core virtual cpu clock. The frequencies of the two cores are tied
together, the highest frequency requested by either core determines
the actual frequency.
Signed-off-by: Colin Cross <ccross@android.com>
- Add drivers to clock lookup table
- Add new pll_m entries
- Support I2C U16 divider
- Fix rate reporting on 32.768kHz clock
- Call propagate rate only if set_rate succeeds
- Add support for audio_sync clock
- Add 24MHz to PLLA frequency list
- Correct i2s1/2/spdifout mux
- Add suspend support
- Fix enable/disable parent clocks in set_parent
- Add max_rate parameter to all clocks
- DVFS support
- Add virtual cpu clock with dvfs
- Support clk_round_rate
- Fix requesting very high periph frequencies
- Add quirks for PLLU:
PLLU is slightly different from the rest of the PLLs. The
lock enable bit is at bit 22 instead of 18 in the MISC
register, and the post divider field is a single bit with
reversed values from other PLLs.
- Simplify recalculating clock rates
- Fix UART divider flags
- Remove unused clock ops
Signed-off-by: Colin Cross <ccross@android.com>
The Tegra SOC contains fuses to identify the CPU type and
bin, and a unique id. The CPU info is required to determine
the correct voltages for each cpu and core frequency.
Signed-off-by: Colin Cross <ccross@android.com>
- the reset values for some pin groups in the tegra pin mux can result in
functional errors due to conflicting with actively-configured pin groups
muxing from the same controller. this change adds a known safe, non-
conflicting mux for every pin group, which can be used on platforms
where the pin group is not routed to any peripheral
- also add each pin group's I/O voltage rail, to enable platform code to
map from the pin groups used by each interface to the regulators used
for dynamic voltage control
- add routines to individually configure the tristate, pin mux and pull-
ups for a pingroup_config array, so that it is possible to program
individual values at run-time without modifying other values.
this allows driver power-management code to reprogram individual
interfaces into lower power states during idle / suspend, or to
reprogram the pin mux to support multiple physical busses per
internal controller (e.g., sharing a single I2C or SPI controller
across multiple pin groups)
- move chip-specific data like pingroups and drive-pingroups
out of the common code and into chip-specific code
- fix debug output for group with no pullups
- add a TEGRA_MUX_SAFE function. Setting a pingroup to TEGRA_MUX_SAFE
will automatically select a mux setting that is guaranteed not to
conflict with any of the hardware blocks.
Signed-off-by: Gary King <gking@nvidia.com>
The "legacy irq controller" duplicates the functionality of the GIC,
but remains powered during the cpu suspend and idle modes that power
down the CPU and the GIC.
Signed-off-by: Colin Cross <ccross@android.com>
v2: fixes from Russell King
- include linux/io.h instead of mach/io.h
v3: fixes from Linus Walleij
- remove /16 * 16 from UART clock
v3:
- Fix checkpatch issues
- make board init calls explicit
- use clock init table to set clocks
- remove panel
Signed-off-by: Colin Cross <ccross@android.com>
Signed-off-by: Erik Gilling <konkers@android.com>
v2: fixes from Russell King
- include linux/io.h instead of asm/io.h
v3:
- Add drive strength controls
- Replace typedef enums with plain enums
Signed-off-by: Erik Gilling <konkers@android.com>
Signed-off-by: Colin Cross <ccross@android.com>
v2: fixes from Mike Rapoport:
- move gpio-names.h to arch/arm/mach-tegra
fixes from Russell King
- include linux/io.h and linux/gpio.h instead of asm/io.h
and asm/gpio.h
additional changes:
- add macros to convert between irq and gpio numbers for platform data
- change for_each_bit to for_each_set_bit in gpio.c
v3:
- minor bugfixes
Signed-off-by: Colin Cross <ccross@android.com>
Signed-off-by: Erik Gilling <konkers@android.com>
v2: fixes from Russell King:
- include linux/io.h instead of asm/io.h
fixes from Gary King:
- remove extra (and incorrect) irq definitions
- use timer 3 instead of timer 1 for compatibility with other drivers
- fix typo that disabled oneshot mode
v3:
- Implement sched_clock
- Fix checkpatch issues
fixes from Gary King:
- Fix incorrect cycles calculation
- Fix min_delta_ns assignment
fixes from Linus Walleij:
- use calc_mult_shift() instead of hard coding values
Signed-off-by: Colin Cross <ccross@android.com>
v2: fixes from Russell King:
- include linux/io.h instead of asm/io.h
- fix whitespace in Kconfig
- Use spin_lock_init to initialize lock
- Return -ENOSYS instead of BUG for unimplemented clock ops
- Use proper return values in tegra2 clock ops
additional changes:
- Rename some clocks to match dev_ids
- add rate propagation
- add debugfs entries
- add support for clock listed in clk_lookup under multiple dev_ids
v3:
- Replace per-clock locking with global clock lock
- Autodetect clock state on init
- Let clock dividers pick next lower possible frequency
- Add support for clock init tables
- Minor bug fixes
- Fix checkpatch issues
Signed-off-by: Colin Cross <ccross@android.com>
v2: fixes from Russell King
- include linux/io.h instead of asm/io.h and mach/io.h
Signed-off-by: Colin Cross <ccross@android.com>
Signed-off-by: Erik Gilling <konkers@android.com>
v2: Fixes from Mike Rapoport
- remove unused header files (mach/dma.h and mach/nand.h)
- remove tegra 1 references from Makefile.boot
v2: fixes from Russell King
- remove mach/io.h include from mach/iomap.h
- fix whitespace in Kconfig
v2: from Colin Cross
- fix invalid immediate in debug-macro.S
v3:
- allow selection of multiple boards
Signed-off-by: Colin Cross <ccross@android.com>
Signed-off-by: Erik Gilling <konkers@android.com>
