ipv6_destopt_rcv() and ipv6_parse_hopopts() pulls these data
- Hop-by-Hop/Destination Options Header : 8
- Hdr Ext Len : skb_transport_header(skb)[1] << 3
and calls ip6_parse_tlv(), so it need not check if skb_headlen() is less
than skb_transport_offset(skb) + (skb_transport_header(skb)[1] << 3).
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We need not reload hdr in ipv6_srh_rcv() unless we call
pskb_expand_head().
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ipv6_rthdr_rcv() pulls these data
- Segment Routing Header : 8
- Hdr Ext Len : skb_transport_header(skb)[1] << 3
needed by ipv6_srh_rcv(), so pskb_pull() in ipv6_srh_rcv() never
fails and can be replaced with skb_pull().
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ipv6_rpl_srh_rcv() checks if ipv6_hdr(skb)->daddr or ohdr->rpl_segaddr[i]
is the multicast address with ipv6_addr_type().
We have the same check for ipv6_hdr(skb)->daddr in ipv6_rthdr_rcv(), so we
need not recheck it in ipv6_rpl_srh_rcv().
Also, we should use ipv6_addr_is_multicast() for ohdr->rpl_segaddr[i]
instead of ipv6_addr_type().
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As Eric Dumazet pointed out [0], ipv6_rthdr_rcv() pulls these data
- Segment Routing Header : 8
- Hdr Ext Len : skb_transport_header(skb)[1] << 3
needed by ipv6_rpl_srh_rcv(). We can remove pskb_may_pull() and
replace pskb_pull() with skb_pull() in ipv6_rpl_srh_rcv().
Link: https://lore.kernel.org/netdev/CANn89iLboLwLrHXeHJucAqBkEL_S0rJFog68t7wwwXO-aNf5Mg@mail.gmail.com/ [0]
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
1) Added a new event handler to firmware sync reset, which is used to
support firmware sync reset flow on smart NIC. Adding this new stage to
the flow enables the firmware to ensure host PFs unload before ECPFs
unload, to avoid race of PFs recovery.
2) Debugfs for mlx5 eswitch bridge offloads
3) Added two new counters for vport stats
4) Minor Fixups and cleanups for net-next branch
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAmSMsbEACgkQSD+KveBX
+j6BAwgAyiZWqA8VEabjJtJNh30Ghfi5OkheAvJmPkd9UlM04EPw4x1dZ/z/jBnU
piBixrs0ou92ZF//Ph1vlf0Jae/YdfKdNcm/FEydspHZC0C2QqeNpDDWl0z3STqB
leBiFPjjBgqYWZWGwgaVlGOyzglTTu5DilkKVy1Ohf7j50P0FppViOsvQle3pAqO
UUXITN8si2AK/03JBJQNIulyyVP+EN9/+d8ZVZagKgurB9Qim9lUbZCerXacEUGV
M/XxYd+pwSAMh3TYlt2x1jv1aSpVwPzIolidJTjUd4gaImi40dw36kNP5BcoSMfr
QEaB1NMv4zfAwiZ7XaXY6/l5wqTjOg==
=vYKY
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2023-06-16' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
mlx5-updates-2023-06-16
1) Added a new event handler to firmware sync reset, which is used to
support firmware sync reset flow on smart NIC. Adding this new stage to
the flow enables the firmware to ensure host PFs unload before ECPFs
unload, to avoid race of PFs recovery.
2) Debugfs for mlx5 eswitch bridge offloads
3) Added two new counters for vport stats
4) Minor Fixups and cleanups for net-next branch
Signed-off-by: David S. Miller <davem@davemloft.net>
The double ifdefs (one for the variable declaration and
one around the code) are quite aesthetically displeasing.
Factor this code out into a helper for easier wrapping.
This will become even more ugly when another skb ext
comparison is added in the future.
The resulting machine code looks the same, the compiler
seems to try to use %rax more and some blocks more around
but I haven't spotted minor differences.
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use devm_regulator_get_enable_optional() instead of hand writing it. It
saves some line of code.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mention that the interrupt line is just asserted for a random period of
time, not the entire time.
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Michael Walle <mwalle@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When af_alg_sendmsg() calls extract_iter_to_sg(), it passes MAX_SGL_ENTS as
the maximum number of elements that may be written to, but some of the
elements may already have been used (as recorded in sgl->cur), so
extract_iter_to_sg() may end up overrunning the scatterlist.
Fix this to limit the number of elements to "MAX_SGL_ENTS - sgl->cur".
Note: It probably makes sense in future to alter the behaviour of
extract_iter_to_sg() to stop if "sgtable->nents >= sg_max" instead, but
this is a smaller fix for now.
The bug causes errors looking something like:
BUG: KASAN: slab-out-of-bounds in sg_assign_page include/linux/scatterlist.h:109 [inline]
BUG: KASAN: slab-out-of-bounds in sg_set_page include/linux/scatterlist.h:139 [inline]
BUG: KASAN: slab-out-of-bounds in extract_bvec_to_sg lib/scatterlist.c:1183 [inline]
BUG: KASAN: slab-out-of-bounds in extract_iter_to_sg lib/scatterlist.c:1352 [inline]
BUG: KASAN: slab-out-of-bounds in extract_iter_to_sg+0x17a6/0x1960 lib/scatterlist.c:1339
Fixes: bf63e250c4 ("crypto: af_alg: Support MSG_SPLICE_PAGES")
Reported-by: syzbot+6efc50cc1f8d718d6cb7@syzkaller.appspotmail.com
Link: https://lore.kernel.org/r/000000000000b2585a05fdeb8379@google.com/
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: syzbot+6efc50cc1f8d718d6cb7@syzkaller.appspotmail.com
cc: Herbert Xu <herbert@gondor.apana.org.au>
cc: "David S. Miller" <davem@davemloft.net>
cc: Eric Dumazet <edumazet@google.com>
cc: Jakub Kicinski <kuba@kernel.org>
cc: Paolo Abeni <pabeni@redhat.com>
cc: Jens Axboe <axboe@kernel.dk>
cc: Matthew Wilcox <willy@infradead.org>
cc: linux-crypto@vger.kernel.org
cc: netdev@vger.kernel.org
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Per-VMA locking allows us to lock a struct vm_area_struct without
taking the process-wide mmap lock in read mode.
Consider a process workload where the mmap lock is taken constantly in
write mode. In this scenario, all zerocopy receives are periodically
blocked during that period of time - though in principle, the memory
ranges being used by TCP are not touched by the operations that need
the mmap write lock. This results in performance degradation.
Now consider another workload where the mmap lock is never taken in
write mode, but there are many TCP connections using receive zerocopy
that are concurrently receiving. These connections all take the mmap
lock in read mode, but this does induce a lot of contention and atomic
ops for this process-wide lock. This results in additional CPU
overhead caused by contending on the cache line for this lock.
However, with per-vma locking, both of these problems can be avoided.
As a test, I ran an RPC-style request/response workload with 4KB
payloads and receive zerocopy enabled, with 100 simultaneous TCP
connections. I measured perf cycles within the
find_tcp_vma/mmap_read_lock/mmap_read_unlock codepath, with and
without per-vma locking enabled.
When using process-wide mmap semaphore read locking, about 1% of
measured perf cycles were within this path. With per-VMA locking, this
value dropped to about 0.45%.
Signed-off-by: Arjun Roy <arjunroy@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under certain circumstances, the tcp receive buffer memory limit
set by autotuning (sk_rcvbuf) is increased due to incoming data
packets as a result of the window not closing when it should be.
This can result in the receive buffer growing all the way up to
tcp_rmem[2], even for tcp sessions with a low BDP.
To reproduce: Connect a TCP session with the receiver doing
nothing and the sender sending small packets (an infinite loop
of socket send() with 4 bytes of payload with a sleep of 1 ms
in between each send()). This will cause the tcp receive buffer
to grow all the way up to tcp_rmem[2].
As a result, a host can have individual tcp sessions with receive
buffers of size tcp_rmem[2], and the host itself can reach tcp_mem
limits, causing the host to go into tcp memory pressure mode.
The fundamental issue is the relationship between the granularity
of the window scaling factor and the number of byte ACKed back
to the sender. This problem has previously been identified in
RFC 7323, appendix F [1].
The Linux kernel currently adheres to never shrinking the window.
In addition to the overallocation of memory mentioned above, the
current behavior is functionally incorrect, because once tcp_rmem[2]
is reached when no remediations remain (i.e. tcp collapse fails to
free up any more memory and there are no packets to prune from the
out-of-order queue), the receiver will drop in-window packets
resulting in retransmissions and an eventual timeout of the tcp
session. A receive buffer full condition should instead result
in a zero window and an indefinite wait.
In practice, this problem is largely hidden for most flows. It
is not applicable to mice flows. Elephant flows can send data
fast enough to "overrun" the sk_rcvbuf limit (in a single ACK),
triggering a zero window.
But this problem does show up for other types of flows. Examples
are websockets and other type of flows that send small amounts of
data spaced apart slightly in time. In these cases, we directly
encounter the problem described in [1].
RFC 7323, section 2.4 [2], says there are instances when a retracted
window can be offered, and that TCP implementations MUST ensure
that they handle a shrinking window, as specified in RFC 1122,
section 4.2.2.16 [3]. All prior RFCs on the topic of tcp window
management have made clear that sender must accept a shrunk window
from the receiver, including RFC 793 [4] and RFC 1323 [5].
This patch implements the functionality to shrink the tcp window
when necessary to keep the right edge within the memory limit by
autotuning (sk_rcvbuf). This new functionality is enabled with
the new sysctl: net.ipv4.tcp_shrink_window
Additional information can be found at:
https://blog.cloudflare.com/unbounded-memory-usage-by-tcp-for-receive-buffers-and-how-we-fixed-it/
[1] https://www.rfc-editor.org/rfc/rfc7323#appendix-F
[2] https://www.rfc-editor.org/rfc/rfc7323#section-2.4
[3] https://www.rfc-editor.org/rfc/rfc1122#page-91
[4] https://www.rfc-editor.org/rfc/rfc793
[5] https://www.rfc-editor.org/rfc/rfc1323
Signed-off-by: Mike Freemon <mfreemon@cloudflare.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current mctp_newroute() contains two exactly same check against
rtm->rtm_type
static int mctp_newroute(...)
{
...
if (rtm->rtm_type != RTN_UNICAST) { // (1)
NL_SET_ERR_MSG(extack, "rtm_type must be RTN_UNICAST");
return -EINVAL;
}
...
if (rtm->rtm_type != RTN_UNICAST) // (2)
return -EINVAL;
...
}
This commits removes the (2) check as it is redundant.
Signed-off-by: Lin Ma <linma@zju.edu.cn>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Acked-by: Jeremy Kerr <jk@codeconstruct.com.au>
Link: https://lore.kernel.org/r/20230615152240.1749428-1-linma@zju.edu.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
kcm_write_msgs() calls unreserve_psock() to release its hold on the
underlying TCP socket if it has run out of things to transmit, but if we
have nothing in the write queue on entry (e.g. because someone did a
zero-length sendmsg), we don't actually go into the transmission loop and
as a consequence don't call reserve_psock().
Fix this by skipping the call to unreserve_psock() if we didn't reserve a
psock.
Fixes: c31a25e1db ("kcm: Send multiple frags in one sendmsg()")
Reported-by: syzbot+dd1339599f1840e4cc65@syzkaller.appspotmail.com
Link: https://lore.kernel.org/r/000000000000a61ffe05fe0c3d08@google.com/
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: syzbot+dd1339599f1840e4cc65@syzkaller.appspotmail.com
cc: Tom Herbert <tom@herbertland.com>
cc: Tom Herbert <tom@quantonium.net>
cc: Jens Axboe <axboe@kernel.dk>
cc: Matthew Wilcox <willy@infradead.org>
Link: https://lore.kernel.org/r/20787.1686828722@warthog.procyon.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
"ecpu" field in struct mlx5_sf_table is not used anywhere. Remove it.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Separate the event API defined in the generic mlx5.h header into
a dedicated header. And remove the TODO comment in commit
69c1280b1f ("net/mlx5: Device events, Use async events chain").
Signed-off-by: Juhee Kang <claudiajkang@gmail.com>
Reviewed-by: Larysa Zaremba <larysa.zaremba@intel.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
This change is needed to use EC VFs with metadata based steering.
There was an assumption that vport was equal to function ID. That's
not the case for EC VF functions. Adjust to function ID and set the
ec_vf_function bit accordingly.
Fixes: 9ac0b12824 ("net/mlx5: Update vport caps query/set for EC VFs")
Signed-off-by: Daniel Jurgens <danielj@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
The last value is not set correctly. This results in representors not
being created for all EC VFs when the base value is higher than 0.
Fixes: a7719b29a8 ("net/mlx5: Add management of EC VF vports")
Signed-off-by: Daniel Jurgens <danielj@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Add counter for number of unicast, multicast and broadcast packets/
octets that were loopback.
Signed-off-by: Or Har-Toov <ohartoov@nvidia.com>
Reviewed-by: Avihai Horon <avihaih@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Add needed HW bits for querying local loopback counter and the
HCA capability for it.
Signed-off-by: Or Har-Toov <ohartoov@nvidia.com>
Reviewed-by: Avihai Horon <avihaih@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
The msglvl support was implemented using the mlx5e_dbg() macro which is
rarely used in the driver, and is not very useful when you can just use
dynamic debug instead.
Remove mlx5e_dbg() and convert its usages to netdev_dbg().
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
These else statement blocks are redundant since the if block already
jumps to the function abort label.
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Reviewed-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Following patch requires access to additional data in bridge net_device.
Pass the whole structure down the stack instead of adding necessary fields
as function arguments one-by-one.
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Following patch in series uses the new directory for bridge FDB debugfs.
The new directory is intended for all future eswitch-specific debugfs
files.
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Added a new event handler to firmware sync reset, which is used to
support firmware sync reset flow on smart NIC. Adding this new stage to
the flow enables the firmware to ensure host PFs unload before ECPFs
unload, to avoid race of PFs recovery.
If firmware sends sync_reset_unload event to driver the driver should
unload and close all HW resources of the function. Once the driver
finishes unloading part, it can't get any more events from firmware as
event queues are closed, so it polls the reset state field to know when
to continue to next stage of the sync reset flow.
Added capability bit for supporting sync_reset_unload event.
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
The Default Timeout Register (DTOR) provides timeout values to driver
for flows that are device dependent. Zero value for DTOR entry is not
valid and should not be used. In case of reading zero value from DTOR,
the driver should use the hard coded SW default value instead.
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Expose new timoueout in Default Timeouts Register to be used on sync
reset flow running on smart NIC. In this flow the driver should know how
much time to wait from getting unload request till firmware will ask the
PF to continue to next stage of the flow.
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Verify at reset_request stage that PF is capable to do reset_now. In
case PF is not capable, notify the firmware that the sync reset can not
happen and so firmware will abort the sync reset at early stage and will
not send reset_now event to any PF.
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Splicing to SOCK_RAW sockets may set MSG_SPLICE_PAGES, but in such a case,
__ip_append_data() will call skb_splice_from_iter() to access the 'from'
data, assuming it to point to a msghdr struct with an iter, instead of
using the provided getfrag function to access it.
In the case of raw_sendmsg(), however, this is not the case and 'from' will
point to a raw_frag_vec struct and raw_getfrag() will be the frag-getting
function. A similar issue may occur with rawv6_sendmsg().
Fix this by ignoring MSG_SPLICE_PAGES if getfrag != ip_generic_getfrag as
ip_generic_getfrag() expects "from" to be a msghdr*, but the other getfrags
don't. Note that this will prevent MSG_SPLICE_PAGES from being effective
for udplite.
This likely affects ping sockets too. udplite looks like it should be okay
as it expects "from" to be a msghdr.
Signed-off-by: David Howells <dhowells@redhat.com>
Reported-by: syzbot+d8486855ef44506fd675@syzkaller.appspotmail.com
Link: https://lore.kernel.org/r/000000000000ae4cbf05fdeb8349@google.com/
Fixes: 2dc334f1a6 ("splice, net: Use sendmsg(MSG_SPLICE_PAGES) rather than ->sendpage()")
Tested-by: syzbot+d8486855ef44506fd675@syzkaller.appspotmail.com
cc: David Ahern <dsahern@kernel.org>
cc: Jens Axboe <axboe@kernel.dk>
cc: Matthew Wilcox <willy@infradead.org>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://lore.kernel.org/r/1410156.1686729856@warthog.procyon.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Functions efx_tc_netdev_event and efx_tc_netevent_event do not exist
in that case as object files tc_bindings.o and tc_encap_actions.o
are not built, so the calls to them from ef100_netdev_event and
ef100_netevent_event cause link errors.
Wrap the corresponding header files (tc_bindings.h, tc_encap_actions.h)
with #if IS_ENABLED(CONFIG_SFC_SRIOV), and add an #else with static
inline stubs for these two functions.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202306102026.ISK5JfUQ-lkp@intel.com/
Fixes: 7e5e7d8000 ("sfc: neighbour lookup for TC encap action offload")
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Reviewed-by: Martin Habets <habetsm.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_ETHERNET=m or CONFIG_FDDI=m, lcs.s has build errors or
warnings:
../drivers/s390/net/lcs.c:40:2: error: #error Cannot compile lcs.c without some net devices switched on.
40 | #error Cannot compile lcs.c without some net devices switched on.
../drivers/s390/net/lcs.c: In function 'lcs_startlan_auto':
../drivers/s390/net/lcs.c:1601:13: warning: unused variable 'rc' [-Wunused-variable]
1601 | int rc;
Solve this by using IS_ENABLED(CONFIG_symbol) instead of ifdef
CONFIG_symbol. The latter only works for builtin (=y) values
while IS_ENABLED() works for builtin or modular values.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Alexandra Winter <wintera@linux.ibm.com>
Cc: Wenjia Zhang <wenjia@linux.ibm.com>
Cc: linux-s390@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Alexander Gordeev <agordeev@linux.ibm.com>
Cc: Christian Borntraeger <borntraeger@linux.ibm.com>
Cc: Sven Schnelle <svens@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement 64 bit per cpu stats to fix the overflow of netdev->stats
on 32 bit platforms. To simplify the code, we use net core
pcpu_sw_netstats infrastructure. One small drawback is some memory
overhead because litex uses just one queue, but we allocate the
counters per cpu.
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Gabriel Somlo <gsomlo@gmail.com>
Link: https://lore.kernel.org/r/20230614162035.300-1-jszhang@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Piotr Gardocki says:
====================
optimize procedure of changing MAC address on interface
The first patch adds an if statement in core to skip early when
the MAC address is not being changes.
The remaining patches remove such checks from Intel drivers
as they're redundant at this point.
====================
Link: https://lore.kernel.org/r/20230614145302.902301-1-piotrx.gardocki@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The check has been moved to core. The ndo_set_mac_address callback
is not being called with new MAC address equal to the old one anymore.
Signed-off-by: Piotr Gardocki <piotrx.gardocki@intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The check has been moved to core. The ndo_set_mac_address callback
is not being called with new MAC address equal to the old one anymore.
Signed-off-by: Piotr Gardocki <piotrx.gardocki@intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In some cases it is possible for kernel to come with request
to change primary MAC address to the address that is already
set on the given interface.
Add proper check to return fast from the function in these cases.
An example of such case is adding an interface to bonding
channel in balance-alb mode:
modprobe bonding mode=balance-alb miimon=100 max_bonds=1
ip link set bond0 up
ifenslave bond0 <eth>
Signed-off-by: Piotr Gardocki <piotrx.gardocki@intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Randy reported that linux-next build warns on PowerPC:
drivers/net/ethernet/freescale/fs_enet/mii-fec.c: In function 'fs_enet_mdio_probe':
drivers/net/ethernet/freescale/fs_enet/mii-fec.c:130:50: warning: format '%x' expects argument of type 'unsigned int', but argument 4 has type 'resource_size_t' {aka 'long long unsigned int'} [-Wformat=]
130 | snprintf(new_bus->id, MII_BUS_ID_SIZE, "%x", res.start);
| ~^ ~~~~~~~~~
| | |
| | resource_size_t {aka long long unsigned int}
| unsigned int
| %llx
Use the right print format.
Link: https://lore.kernel.org/all/8f9f8d38-d9c7-9f1b-feb0-103d76902d14@infradead.org/
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Link: https://lore.kernel.org/r/20230615035231.2184880-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
splice_to_socket() assumes that a pipe_buffer won't hold more than a single
page of data - but this assumption can be violated by skb_splice_bits()
when it splices from a socket into a pipe.
The problem is that splice_to_socket() doesn't advance the pipe_buffer
length and offset when transcribing from the pipe buf into a bio_vec, so if
the buf is >PAGE_SIZE, it keeps repeating the same initial chunk and
doesn't advance the tail index. It then subtracts this from "remain" and
overcounts the amount of data to be sent.
The cleanup phase then tries to overclean the pipe, hits an unused pipe buf
and a NULL-pointer dereference occurs.
Fix this by not restricting the bio_vec size to PAGE_SIZE and instead
transcribing the entirety of each pipe_buffer into a single bio_vec and
advancing the tail index if remain hasn't hit zero yet.
Large bio_vecs will then be split up by iterator functions such as
iov_iter_extract_pages().
This resulted in a KASAN report looking like:
general protection fault, probably for non-canonical address 0xdffffc0000000001: 0000 [#1] PREEMPT SMP KASAN
KASAN: null-ptr-deref in range [0x0000000000000008-0x000000000000000f]
...
RIP: 0010:pipe_buf_release include/linux/pipe_fs_i.h:203 [inline]
RIP: 0010:splice_to_socket+0xa91/0xe30 fs/splice.c:933
Fixes: 2dc334f1a6 ("splice, net: Use sendmsg(MSG_SPLICE_PAGES) rather than ->sendpage()")
Reported-by: syzbot+f9e28a23426ac3b24f20@syzkaller.appspotmail.com
Link: https://lore.kernel.org/r/0000000000000900e905fdeb8e39@google.com/
Tested-by: syzbot+f9e28a23426ac3b24f20@syzkaller.appspotmail.com
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Willem de Bruijn <willemdebruijn.kernel@gmail.com>
cc: David Ahern <dsahern@kernel.org>
cc: Jens Axboe <axboe@kernel.dk>
cc: Matthew Wilcox <willy@infradead.org>
cc: Christian Brauner <brauner@kernel.org>
cc: Alexander Viro <viro@zeniv.linux.org.uk>
Link: https://lore.kernel.org/r/1428985.1686737388@warthog.procyon.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After merging the net-next tree, today's linux-next build (sparc64
defconfig) failed like this:
drivers/net/ethernet/sun/sunvnet_common.c: In function 'vnet_handle_offloads':
drivers/net/ethernet/sun/sunvnet_common.c:1277:16: error: implicit declaration of function 'skb_gso_segment'; did you mean 'skb_gso_reset'? [-Werror=implicit-function-declaration]
1277 | segs = skb_gso_segment(skb, dev->features & ~NETIF_F_TSO);
| ^~~~~~~~~~~~~~~
| skb_gso_reset
drivers/net/ethernet/sun/sunvnet_common.c:1277:14: warning: assignment to 'struct sk_buff *' from 'int' makes pointer from integer without a cast [-Wint-conversion]
1277 | segs = skb_gso_segment(skb, dev->features & ~NETIF_F_TSO);
| ^
Fixes: d457a0e329 ("net: move gso declarations and functions to their own files")
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230613164639.164b2991@canb.auug.org.au
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The current implementation allocates page-sized rx buffers.
As traffic may consist of different types and sizes of packets,
in various cases, buffers are not fully used.
This change (Dynamic RX Buffers - DRB) uses part of the allocated rx
page needed for the incoming packet, and returns the rest of the
unused page to be used again as an rx buffer for future packets.
A threshold of 2K for unused space has been set in order to declare
whether the remainder of the page can be reused again as an rx buffer.
As a page may be reused, dma_sync_single_for_cpu() is added in order
to sync the memory to the CPU side after it was owned by the HW.
In addition, when the rx page can no longer be reused, it is being
unmapped using dma_page_unmap(), which implicitly syncs and then
unmaps the entire page. In case the kernel still handles the skbs
pointing to the previous buffers from that rx page, it may access
garbage pointers, caused by the implicit sync overwriting them.
The implicit dma sync is removed by replacing dma_page_unmap() with
dma_unmap_page_attrs() with DMA_ATTR_SKIP_CPU_SYNC flag.
The functionality is disabled for XDP traffic to avoid handling
several descriptors per packet.
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: David Arinzon <darinzon@amazon.com>
Link: https://lore.kernel.org/r/20230612121448.28829-1-darinzon@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Most of the ioctls to net protocols operates directly on userspace
argument (arg). Usually doing get_user()/put_user() directly in the
ioctl callback. This is not flexible, because it is hard to reuse these
functions without passing userspace buffers.
Change the "struct proto" ioctls to avoid touching userspace memory and
operate on kernel buffers, i.e., all protocol's ioctl callbacks is
adapted to operate on a kernel memory other than on userspace (so, no
more {put,get}_user() and friends being called in the ioctl callback).
This changes the "struct proto" ioctl format in the following way:
int (*ioctl)(struct sock *sk, int cmd,
- unsigned long arg);
+ int *karg);
(Important to say that this patch does not touch the "struct proto_ops"
protocols)
So, the "karg" argument, which is passed to the ioctl callback, is a
pointer allocated to kernel space memory (inside a function wrapper).
This buffer (karg) may contain input argument (copied from userspace in
a prep function) and it might return a value/buffer, which is copied
back to userspace if necessary. There is not one-size-fits-all format
(that is I am using 'may' above), but basically, there are three type of
ioctls:
1) Do not read from userspace, returns a result to userspace
2) Read an input parameter from userspace, and does not return anything
to userspace
3) Read an input from userspace, and return a buffer to userspace.
The default case (1) (where no input parameter is given, and an "int" is
returned to userspace) encompasses more than 90% of the cases, but there
are two other exceptions. Here is a list of exceptions:
* Protocol RAW:
* cmd = SIOCGETVIFCNT:
* input and output = struct sioc_vif_req
* cmd = SIOCGETSGCNT
* input and output = struct sioc_sg_req
* Explanation: for the SIOCGETVIFCNT case, userspace passes the input
argument, which is struct sioc_vif_req. Then the callback populates
the struct, which is copied back to userspace.
* Protocol RAW6:
* cmd = SIOCGETMIFCNT_IN6
* input and output = struct sioc_mif_req6
* cmd = SIOCGETSGCNT_IN6
* input and output = struct sioc_sg_req6
* Protocol PHONET:
* cmd == SIOCPNADDRESOURCE | SIOCPNDELRESOURCE
* input int (4 bytes)
* Nothing is copied back to userspace.
For the exception cases, functions sock_sk_ioctl_inout() will
copy the userspace input, and copy it back to kernel space.
The wrapper that prepare the buffer and put the buffer back to user is
sk_ioctl(), so, instead of calling sk->sk_prot->ioctl(), the callee now
calls sk_ioctl(), which will handle all cases.
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Link: https://lore.kernel.org/r/20230609152800.830401-1-leitao@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Selftests excluded - we have 58 patches and diff of +442/-199,
which isn't really small but perhaps with the exception of
the WiFi locking change it's old(ish) bugs.
We have no known problems with v6.4.
The selftest changes are rather large as MPTCP folks try to apply
Greg's guidance that selftest from torvalds/linux should be able
to run against stable kernels.
Last thing I should call out is the DCCP/UDP-lite deprecation notices,
we are fairly sure those are dead, but if we're wrong reverting them
back in won't be fun.
Current release - regressions:
- wifi:
- cfg80211: fix double lock bug in reg_wdev_chan_valid()
- iwlwifi: mvm: spin_lock_bh() to fix lockdep regression
Current release - new code bugs:
- handshake: remove fput() that causes use-after-free
Previous releases - regressions:
- sched: cls_u32: fix reference counter leak leading to overflow
- sched: cls_api: fix lockup on flushing explicitly created chain
Previous releases - always broken:
- nf_tables: integrate pipapo into commit protocol
- nf_tables: incorrect error path handling with NFT_MSG_NEWRULE,
fix dangling pointer on failure
- ping6: fix send to link-local addresses with VRF
- sched: act_pedit: parse L3 header for L4 offset, the skb may
not have the offset saved
- sched: act_ct: fix promotion of offloaded unreplied tuple
- sched: refuse to destroy an ingress and clsact Qdiscs if there
are lockless change operations in flight
- wifi: mac80211: fix handful of bugs in multi-link operation
- ipvlan: fix bound dev checking for IPv6 l3s mode
- eth: enetc: correct the indexes of highest and 2nd highest TCs
- eth: ice: fix XDP memory leak when NIC is brought up and down
Misc:
- add deprecation notices for UDP-lite and DCCP
- selftests: mptcp: skip tests not supported by old kernels
- sctp: handle invalid error codes without calling BUG()
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=oNA0
-----END PGP SIGNATURE-----
Merge tag 'net-6.4-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from wireless, and netfilter.
Selftests excluded - we have 58 patches and diff of +442/-199, which
isn't really small but perhaps with the exception of the WiFi locking
change it's old(ish) bugs.
We have no known problems with v6.4.
The selftest changes are rather large as MPTCP folks try to apply
Greg's guidance that selftest from torvalds/linux should be able to
run against stable kernels.
Last thing I should call out is the DCCP/UDP-lite deprecation notices.
We are fairly sure those are dead, but if we're wrong reverting them
back in won't be fun.
Current release - regressions:
- wifi:
- cfg80211: fix double lock bug in reg_wdev_chan_valid()
- iwlwifi: mvm: spin_lock_bh() to fix lockdep regression
Current release - new code bugs:
- handshake: remove fput() that causes use-after-free
Previous releases - regressions:
- sched: cls_u32: fix reference counter leak leading to overflow
- sched: cls_api: fix lockup on flushing explicitly created chain
Previous releases - always broken:
- nf_tables: integrate pipapo into commit protocol
- nf_tables: incorrect error path handling with NFT_MSG_NEWRULE, fix
dangling pointer on failure
- ping6: fix send to link-local addresses with VRF
- sched: act_pedit: parse L3 header for L4 offset, the skb may not
have the offset saved
- sched: act_ct: fix promotion of offloaded unreplied tuple
- sched: refuse to destroy an ingress and clsact Qdiscs if there are
lockless change operations in flight
- wifi: mac80211: fix handful of bugs in multi-link operation
- ipvlan: fix bound dev checking for IPv6 l3s mode
- eth: enetc: correct the indexes of highest and 2nd highest TCs
- eth: ice: fix XDP memory leak when NIC is brought up and down
Misc:
- add deprecation notices for UDP-lite and DCCP
- selftests: mptcp: skip tests not supported by old kernels
- sctp: handle invalid error codes without calling BUG()"
* tag 'net-6.4-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (91 commits)
dccp: Print deprecation notice.
udplite: Print deprecation notice.
octeon_ep: Add missing check for ioremap
selftests/ptp: Fix timestamp printf format for PTP_SYS_OFFSET
net: ethernet: stmicro: stmmac: fix possible memory leak in __stmmac_open
net: tipc: resize nlattr array to correct size
sfc: fix XDP queues mode with legacy IRQ
net: macsec: fix double free of percpu stats
net: lapbether: only support ethernet devices
MAINTAINERS: add reviewers for SMC Sockets
s390/ism: Fix trying to free already-freed IRQ by repeated ism_dev_exit()
net: dsa: felix: fix taprio guard band overflow at 10Mbps with jumbo frames
net/sched: cls_api: Fix lockup on flushing explicitly created chain
ice: Fix ice module unload
net/handshake: remove fput() that causes use-after-free
selftests: forwarding: hw_stats_l3: Set addrgenmode in a separate step
net/sched: qdisc_destroy() old ingress and clsact Qdiscs before grafting
net/sched: Refactor qdisc_graft() for ingress and clsact Qdiscs
net/sched: act_ct: Fix promotion of offloaded unreplied tuple
wifi: iwlwifi: mvm: spin_lock_bh() to fix lockdep regression
...
merge; where DM core was splitting large discards every 128K
(max_sectors_kb) rather than every 64M (discard_max_bytes).
- Extend DM core LOCKFS fix, made during 6.4 merge, to also fix race
between do_mount and dm's do_suspend (in addition to the earlier
fix's do_mount race with dm's do_resume).
- Fix DM thin metadata operations to first check if the thin-pool is
in "fail_io" mode; otherwise UAF can occur.
- Fix DM thinp's call to __blkdev_issue_discard to use GFP_NOIO rather
than GFP_NOWAIT (__blkdev_issue_discard cannot handle NULL return
from bio_alloc).
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEJfWUX4UqZ4x1O2wixSPxCi2dA1oFAmSLTh0ACgkQxSPxCi2d
A1rmqggAildPKBjT8nqZmU86lpsy60E03OwvBnGPkMF5pjkOUmTjkb5EWVSAmeuO
ojj0pWlC+1ZvVkiDfkWxt0NL/4ETD4q+5oy1ARBcOawPX6bj0eXLoBr6m10b+KOb
mKAoXgYrESEzQ2qPBe4a4Lj3zIBXzXpMpW9TtF23z4HnDpnwpED5xNPWBgiWc3O/
/6MF1ASLp0DWldoL+gmIp9hEzyQzbzgM4uBOGC4UAYk3U1I55qwX6bWDZ9cQNGMh
AqCSrphuKHvbsb31yb1X3hB3g1XbAeSvvcizgFY0g9ZpncddKm5gx0BWVDO7qGBG
UxLIec19kQ2CIEx/QJZIhEjneLlJ/g==
=mME4
-----END PGP SIGNATURE-----
Merge tag 'for-6.4/dm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
- Fix DM thinp discard performance regression introduced during this
merge window where DM core was splitting large discards every 128K
(max_sectors_kb) rather than every 64M (discard_max_bytes).
- Extend DM core LOCKFS fix, made during 6.4 merge, to also fix race
between do_mount and dm's do_suspend (in addition to the earlier
fix's do_mount race with dm's do_resume).
- Fix DM thin metadata operations to first check if the thin-pool is in
"fail_io" mode; otherwise UAF can occur.
- Fix DM thinp's call to __blkdev_issue_discard to use GFP_NOIO rather
than GFP_NOWAIT (__blkdev_issue_discard cannot handle NULL return
from bio_alloc).
* tag 'for-6.4/dm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm: use op specific max_sectors when splitting abnormal io
dm thin: fix issue_discard to pass GFP_NOIO to __blkdev_issue_discard
dm thin metadata: check fail_io before using data_sm
dm: don't lock fs when the map is NULL during suspend or resume
