If the kernel supports both G5 and pSeries, and CONFIG_EEH is enabled,
eeh_init() is (quite reasonably) never called when we boot on a G5. Yet
eeh_check_failure() still gets called. We should avoid doing that if
!eeh_subsystem_enabled.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
PowerPC's NUMA domain doesn't currently set up some of the newer
sched-domains parameters.
Brian Twichell <tbrian@us.ibm.com> discovered and diagnosed a 1.5% OLTP
database regression on a 4 core POWER5 system that was due to the use of
NUMA scheduling on ppc64.
This patch applies some saneish values to the parameters, in line with
other architectures. This solves the regression.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In the old days when arm26/arm32 was combined into the same
architecture, proc-fns.h provided the xchg implementation for
arm26 CPUs. Since we no longer combine these two, this include
is no longer required. Remove it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since atomic.h does not include types.h, u32 may not be defined.
Since atomics are supposed to work on unsigned long quantities,
use unsigned long instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Unfortunately, using PAGE_SHIFT in asm/arch/memory.h is unsafe, and we
can't include asm/page.h into this file because then we have a circular
dependency. Move the offending code to arch/arm/common/sa1111.c
instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
atomic.h, bitops.h and mmu_context.h are using likely/unlikely.
thread_info.h uses __attribute_const__. Hence these files require
linux/compiler.h to be included.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
If 'old' and 'oldval' are different then 'res' never gets set. In that
case, if ever %0 happened to contain anything but zero (rather likely)
then the code will loop forever (or until another CPU just come along
and change the atomic value to match 'old' which is rather unlikely).
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move __io_address to arch-realview/hardware.h, drop core.h from platsmp.c
and localtimer.c, and include asm/io.h where required.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Based upon a patch by Guido Guenther <agx@sigxcpu.org>.
Some of these ioctls had embedded time_t objects
or pointers, so needed translation.
Signed-off-by: David S. Miller <davem@davemloft.net>
The vDSO functions should have the same calling convention as a syscall.
Unfortunately, they currently don't set the cr0.so bit which is used to
indicate an error. This patch makes them clear this bit unconditionally
since all functions currently succeed. The syscall fallback done by some
of them will eventually override this if the syscall fails.
This also changes the symbol version of all vdso exports to make sure
glibc can differenciate between old and fixed calls for existing ones
like __kernel_gettimeofday.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
page_to_virt and lowmem_page_address provided equiavlent functionality
so use the more standard lowmem_page_address
This also addresses build issue in ARCH=powerpc since page_to_virt()
has been removed from include/asm-powerpc/page.h
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
I discovered that in some cases (PowerMac for example) we wouldn't
properly map the PCI IO space on recent kernels. In addition, the code
for initializing PCI host bridges was scattered all over the place with
some duplication between platforms.
This patch fixes the problem and does a small cleanup by creating a
pcibios_alloc_controller() in pci_64.c that is similar to the one in
pci_32.c (just takes an additional device node argument) that takes care
of all the grunt allocation and initialisation work. It should work for
both boot time and dynamically allocated PHBs.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Make sysctl.h (again) useable from userspace
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Acked-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is needed for large multinode IBM systems which have a sparse
APIC space in clustered mode, fully covering the available 8 bits.
The previous kernels would limit the local APIC number to 127,
which caused it to reject some of the CPUs at boot.
I increased the maximum and shrunk the apic_version array a bit
to make up for that (the version is only 8 bit, so don't need
an full int to store)
Cc: Chris McDermott <lcm@us.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Keeping this function does not makes sense because it's a copied (and
buggy) copy of sys_time. The only difference is that now.tv_sec (which is
a time_t, i.e. a 64-bit long) is copied (and truncated) into a int
(32-bit).
The prototype is the same (they both take a long __user *), so let's drop
this and redirect it to sys_time (and make sure it exists by defining
__ARCH_WANT_SYS_TIME).
Only disadvantage is that the sys_stime definition is also compiled (may be
fixed if needed by adding a separate __ARCH_WANT_SYS_STIME macro, and
defining it for all arch's defining __ARCH_WANT_SYS_TIME except x86_64).
Acked-by: Andi Kleen <ak@suse.de>
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The current value was correct before the introduction of Intel EM64T support -
but now L1_CACHE_SHIFT_MAX can be less than L1_CACHE_SHIFT, which _is_ funny!
Between the few users of ____cacheline_maxaligned_in_smp, we also have (for
example) rcu_ctrlblk, and struct zone, with zone->{lru_,}lock. I.e. we have
a lot of excess cacheline bouncing on them.
No correctness issues, obviously. So this could even be merged for 2.6.14
(I'm not a fan of this idea, though).
CC: Andi Kleen <ak@suse.de>
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Not needed since x86-64 always uses the spinlock based rwsems.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Old code could retry for 10 seconds worst time. Only try it
for one second now.
Suggested by Yinghai Lu
Cc: Yinghai.Lu@amd.com
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fields obtained through cpuid vector 0x1(ebx[16:23]) and
vector 0x4(eax[14:25], eax[26:31]) indicate the maximum values and might not
always be the same as what is available and what OS sees. So make sure
"siblings" and "cpu cores" values in /proc/cpuinfo reflect the values as seen
by OS instead of what cpuid instruction says. This will also fix the buggy BIOS
cases (for example where cpuid on a single core cpu says there are "2" siblings,
even when HT is disabled in the BIOS.
http://bugzilla.kernel.org/show_bug.cgi?id=4359)
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
With a NR_CPUS==128 kernel with CPU hotplug enabled we would waste 4MB
on per CPU data of all possible CPUs. The reason was that HOTPLUG
always set up possible map to NR_CPUS cpus and then we need to allocate
that much (each per CPU data is roughly ~32k now)
The underlying problem is that ACPI didn't tell us how many hotplug CPUs
the platform supports. So the old code just assumed all, which would
lead to this memory wastage.
This implements some new heuristics:
- If the BIOS specified disabled CPUs in the ACPI/mptables assume they
can be enabled later (this is bending the ACPI specification a bit,
but seems like a obvious extension)
- The user can overwrite it with a new additionals_cpus=NUM option
- Otherwise use half of the available CPUs or 2, whatever is more.
Cc: ashok.raj@intel.com
Cc: len.brown@intel.com
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Adding __initdata_* to asm-generic/sections.h
Replaces a lot of open coded externs in arch/x86_64/*
I had to change __bss_end to __bss_stop to match the other architectures.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It is for physical addresses, not for PFNs.
Pointed out by Tejun Heo.
Cc: htejun@gmail.com
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We should zap the low mappings, as soon as possible, so that we can catch
kernel bugs more effectively. Previously early boot had NULL mapped
and didn't trap on NULL references.
This patch introduces boot_level4_pgt, which will always have low identity
addresses mapped. Druing boot, all the processors will use this as their
level4 pgt. On BP, we will switch to init_level4_pgt as soon as we enter C
code and zap the low mappings as soon as we are done with the usage of
identity low mapped addresses. On AP's we will zap the low mappings as
soon as we jump to C code.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Not go from the CPU number to an mapping array.
Mode number is often used now in fast paths.
This also adds a generic numa_node_id to all the topology includes
Suggested by Eric Dumazet
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Has been introduced for x86-64 at some point to save memory
in struct page, but has been obsolete for some time. Just
remove it.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
pfn_to_page really requires pfn_valid to be true now, no question.
Some people stumbled over it, but it was misleading and wrong.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Here's a patch that builds on Natalie Protasevich's IRQ compression
patch and tries to work for MPS boots as well as ACPI. It is meant for
a 4-node IBM x460 NUMA box, which was dying because it had interrupt
pins with GSI numbers > NR_IRQS and thus overflowed irq_desc.
The problem is that this system has 270 GSIs (which are 1:1 mapped with
I/O APIC RTEs) and an 8-node box would have 540. This is much bigger
than NR_IRQS (224 for both i386 and x86_64). Also, there aren't enough
vectors to go around. There are about 190 usable vectors, not counting
the reserved ones and the unused vectors at 0x20 to 0x2F. So, my patch
attempts to compress the GSI range and share vectors by sharing IRQs.
Cc: "Protasevich, Natalie" <Natalie.Protasevich@unisys.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
MC4_MISC - DRAM Errors Threshold Register realized under AMD K8 Rev F.
This register is used to count correctable and uncorrectable ECC errors that occur during DRAM read operations.
The user may interface through sysfs files in order to change the threshold configuration.
bank%d/error_count - reads current error count, write to clear.
bank%d/interrupt_enable - set/clear interrupt enable.
bank%d/threshold_limit - read/write the threshold limit.
APIC vector 0xF9 in hw_irq.h.
5 software defined bank ids in mce.h.
new apic.c function to setup threshold apic lvt.
defaults to interrupt off, count enabled, and threshold limit max.
sysfs interface created on /sys/devices/system/threshold.
AK: added some ifdefs to make it compile on UP
Signed-off-by: Jacob Shin <jacob.shin@amd.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a new 4GB GFP_DMA32 zone between the GFP_DMA and GFP_NORMAL zones.
As a bit of historical background: when the x86-64 port
was originally designed we had some discussion if we should
use a 16MB DMA zone like i386 or a 4GB DMA zone like IA64 or
both. Both was ruled out at this point because it was in early
2.4 when VM is still quite shakey and had bad troubles even
dealing with one DMA zone. We settled on the 16MB DMA zone mainly
because we worried about older soundcards and the floppy.
But this has always caused problems since then because
device drivers had trouble getting enough DMA able memory. These days
the VM works much better and the wide use of NUMA has proven
it can deal with many zones successfully.
So this patch adds both zones.
This helps drivers who need a lot of memory below 4GB because
their hardware is not accessing more (graphic drivers - proprietary
and free ones, video frame buffer drivers, sound drivers etc.).
Previously they could only use IOMMU+16MB GFP_DMA, which
was not enough memory.
Another common problem is that hardware who has full memory
addressing for >4GB misses it for some control structures in memory
(like transmit rings or other metadata). They tended to allocate memory
in the 16MB GFP_DMA or the IOMMU/swiotlb then using pci_alloc_consistent,
but that can tie up a lot of precious 16MB GFPDMA/IOMMU/swiotlb memory
(even on AMD systems the IOMMU tends to be quite small) especially if you have
many devices. With the new zone pci_alloc_consistent can just put
this stuff into memory below 4GB which works better.
One argument was still if the zone should be 4GB or 2GB. The main
motivation for 2GB would be an unnamed not so unpopular hardware
raid controller (mostly found in older machines from a particular four letter
company) who has a strange 2GB restriction in firmware. But
that one works ok with swiotlb/IOMMU anyways, so it doesn't really
need GFP_DMA32. I chose 4GB to be compatible with IA64 and because
it seems to be the most common restriction.
The new zone is so far added only for x86-64.
For other architectures who don't set up this
new zone nothing changes. Architectures can set a compatibility
define in Kconfig CONFIG_DMA_IS_DMA32 that will define GFP_DMA32
as GFP_DMA. Otherwise it's a nop because on 32bit architectures
it's normally not needed because GFP_NORMAL (=0) is DMA able
enough.
One problem is still that GFP_DMA means different things on different
architectures. e.g. some drivers used to have #ifdef ia64 use GFP_DMA
(trusting it to be 4GB) #elif __x86_64__ (use other hacks like
the swiotlb because 16MB is not enough) ... . This was quite
ugly and is now obsolete.
These should be now converted to use GFP_DMA32 unconditionally. I haven't done
this yet. Or best only use pci_alloc_consistent/dma_alloc_coherent
which will use GFP_DMA32 transparently.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch unconditionally requires CAP_NET_ADMIN for all nfnetlink
messages. It also removes the per-message cap_required field, since all
existing subsystems use CAP_NET_ADMIN for all their messages anyway.
Patrick McHardy owes me a beer if we ever need to re-introduce this.
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Skip sizecheck if the size of the attribute wasn't specified, ie. zero.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
- in ata_dev_identify(), don't assume that all devices are either
ATA or ATAPI. In the future, this code will see port multipliers
and other devices.
- make a debugging printk less verbose
- add new helper ata_qc_reinit()
- add new helper BPRINTK() and port flag ATA_FLAG_DEBUGMSG, for
fine-grained debugging use.
Also deletes files in arch/ppc64 that are no longer used now that
we don't compile with ARCH=ppc64 any more.
Signed-off-by: Paul Mackerras <paulus@samba.org>
... and also delete some that are no longer used because we already
had an include/asm-powerpc version of the header.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes various errors in the new functions added in the vDSO's,
I've now verified all functions on both 32 and 64 bits vDSOs. It also
fix a sign extension bug getting the initial time of day at boot that
could cause the monotonic clock value to be completely on bogus for
64 bits applications (with either the vDSO or the syscall) on
powermacs.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The userspace kexec-tools need to know the location of the htab on non-lpar
machines, as well as the end of the kernel. Export via the device tree.
NB. This patch has been updated to use "linux,x" property names. You may
need to update your kexec-tools to match.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We currently have a ppc_md member called cpu_irq_down, which disables IRQs
for the cpu in question. The only caller of cpu_irq_down is the kexec code.
On pSeries we need to do more than just teardown IRQs at kexec time, so rename
the ppc_md member to kexec_cpu_down and expand it. The pSeries code needs to
know, and other platforms might too, whether we're doing a crash shutdown (ie.
panicking) or a regular kexec, so add a flag for that.
The pSeries implementation of kexec_cpu_down does an unregister VPA call, which
tells the Hypervisor to stop writing stuff into our pacas. Without this we can
get weird memory corruption bugs when we kexec, caused by the Hypervisor
writing into the first kernel's pacas which happens to be somewhere interesting
in the second kernel's memory.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Merge asm-ppc/page.h and asm-ppc64/page.h into asm-powerpc/page.h,
asm-powerpc/page_32.h and asm-powerpc/page_64.h
Built for PPC (common_defconfig), with ARCH=powerpc, mostly built with
ARCH=ppc (other things break the build). Built and booted on P5 LPAR
for PPC64 with ARCH=ppc/powerpc (pseries_defconfig). Mostly built for
iSeries powerpc.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Many structures contain both an internal part and one which is part of the API
to other modules. With this patch it is possible to only include these public
members in the kernel documentation.
Signed-off-by: Martin Waitz <tali@admingilde.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Adds a new include for internal V4L2 ioctls and API
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- The pinnacle handler & remote are common to saa7134 PCI boards and em28xx
USB boards, so the keymap was moved to ir-common and the keyhandler is back
to ir-kbd-i2c
- request_module("ir-kbd-i2c") is no longer necessary at saa7134-core since
saa7134.ko now depends on ir-kbd-i2c.ko to get the keyhandler
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Added SECAM L' video standard
- SECAM L' is a Secam variant that requires special config.
This patch adds support on V4L core. Requires aditional patches
on tuners to support.
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It would appear that the timespec normalize code has an off by one error.
Found in three places. Thanks to Ben for spotting.
Signed-off-by: George Anzinger<george@mvista.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
allnoconfig:
In file included from fs/super.c:28:
include/linux/acct.h:173: warning: `TICK_NSEC' is not defined
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
put_ioctx's refcount debugging was doing an atomic_read after dropping its
reference when it wasn't the last ref, leaving a tiny race for another freeing
thread to sneak into. This shifts the debugging before the ops, uses BUG_ON,
and reformats the defines a little. Sadly, moving to inlines increased the
code size but this change decreases the code size by a whole 9 bytes :)
Signed-off-by: Zach Brown <zach.brown@oracle.com>
Cc: Benjamin LaHaise <bcrl@kvack.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Sync iocbs have a life cycle that don't need a kioctx. Their retrying, if
any, is done in the context of their owner who has allocated them on the
stack.
The sole user of a sync iocb's ctx reference was aio_complete() checking for
an elevated iocb ref count that could never happen. No path which grabs an
iocb ref has access to sync iocbs.
If we were to implement sync iocb cancelation it would be done by the owner of
the iocb using its on-stack reference.
Removing this chunk from aio_complete allows us to remove the entire kioctx
instance from mm_struct, reducing its size by a third. On a i386 testing box
the slab size went from 768 to 504 bytes and from 5 to 8 per page.
Signed-off-by: Zach Brown <zach.brown@oracle.com>
Acked-by: Benjamin LaHaise <bcrl@kvack.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Introduce an atomic_inc_not_zero operation. Make this a special case of
atomic_add_unless because lockless pagecache actually wants
atomic_inc_not_negativeone due to its offset refcount.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: "Paul E. McKenney" <paulmck@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Make cmpxchg generally available on the i386 platform.
- Provide emulation of cmpxchg suitable for uniprocessor if built and run on
386.
From: Christoph Lameter <clameter@sgi.com>
- Cut down patch and small style changes.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: "Paul E. McKenney" <paulmck@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Currently per_cpu_ptr() doesn't really do anything with 'cpu' in the UP
case. This is problematic in the cases where this is the only place the
variable is referenced:
CC kernel/workqueue.o
kernel/workqueue.c: In function `current_is_keventd':
kernel/workqueue.c:460: warning: unused variable `cpu'
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove task_work structure, use the standard thread flags functions and use
shifts in entry.S to test the thread flags. Add a few local labels to entry.S
to allow gas to generate short jumps.
Finally it changes a number of inline functions in thread_info.h to macros to
delay the current_thread_info() usage, which requires on m68k a structure
(task_struct) not yet defined at this point.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Cc: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
a) added embedded thread_info [m68k processor.h]
b) added missing symbols in asm-offsets.c
c) task_thread_info() and friends in asm-m68k/thread_info.h
d) made m68k thread_info.h included by m68k processor.h, not the other way
round.
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
a) in smp_lock.h #include of sched.h and spinlock.h moved under #ifdef
CONFIG_LOCK_KERNEL.
b) interrupt.h now explicitly pulls sched.h (not via smp_lock.h from
hardirq.h as it used to)
c) in three more places we need changes to compensate for (a) - one place
in arch/sparc needs string.h now, hardirq.h needs forward declaration of
task_struct and preempt.h needs direct include of thread_info.h.
d) thread_info-related helpers in sched.h and thread_info.h put under
ifndef __HAVE_THREAD_FUNCTIONS. Obviously safe.
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
encapsulates the rest of arch-dependent operations with thread_info access.
Two new helpers - setup_thread_stack() and end_of_stack(). For normal case
the former consists of copying thread_info of parent to new thread_info and
the latter returns pointer immediately past the end of thread_info.
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
new helper - task_thread_info(task). On platforms that have thread_info
allocated separately (i.e. in default case) it simply returns
task->thread_info. m68k wants (and for good reasons) to embed its thread_info
into task_struct. So it will (in later patch) have task_thread_info() of its
own. For now we just add a macro for generic case and convert existing
instances of its body in core kernel to uses of new macro. Obviously safe -
all normal architectures get the same preprocessor output they used to get.
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Enablement patch for the new PowerBooks (late 2005 edition).
This enables the ATA controller, Gigabit ethernet and basic AGP setup.
Bluetooth works out-of-the box after running hid2hci.
Still remaining is to get the touchpad to work, the simple change of just
adding the new USB ids isn't enough.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove last remnant of the defunct early reclaim page logic, the no longer
used __GFP_NORECLAIM flag bit.
Signed-off-by: Paul Jackson <pj@sgi.com>
Acked-by: Martin Hicks <mort@bork.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Clean up of __alloc_pages.
Restoration of previous behaviour, plus further cleanups by introducing an
'alloc_flags', removing the last of should_reclaim_zone.
Signed-off-by: Rohit Seth <rohit.seth@intel.com>
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The address based work estimate for unmapping (for lockbreak) is and always
was horribly inefficient for sparse mappings. The problem is most simply
explained with an example:
If we find a pgd is clear, we still have to call into unmap_page_range
PGDIR_SIZE / ZAP_BLOCK_SIZE times, each time checking the clear pgd, in
order to progress the working address to the next pgd.
The fundamental way to solve the problem is to keep track of the end
address we've processed and pass it back to the higher layers.
From: Nick Piggin <npiggin@suse.de>
Modification to completely get away from address based work estimate
and instead use an abstract count, with a very small cost for empty
entries as opposed to present pages.
On 2.6.14-git2, ppc64, and CONFIG_PREEMPT=y, mapping and unmapping 1TB
of virtual address space takes 1.69s; with the following patch applied,
this operation can be done 1000 times in less than 0.01s
From: Andrew Morton <akpm@osdl.org>
With CONFIG_HUTETLB_PAGE=n:
mm/memory.c: In function `unmap_vmas':
mm/memory.c:779: warning: division by zero
Due to
zap_work -= (end - start) /
(HPAGE_SIZE / PAGE_SIZE);
So make the dummy HPAGE_SIZE non-zero
Signed-off-by: Robin Holt <holt@sgi.com>
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Changed jobs and the Freescale address is no longer valid.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Since few people need the support anymore, this moves the legacy
pm_xxx functions to CONFIG_PM_LEGACY, and include/linux/pm_legacy.h.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The file_lock spinlock sits close to mostly read fields of 'struct
files_struct'
In SMP (and NUMA) environments, each time a thread wants to open or close
a file, it has to acquire the spinlock, thus invalidating the cache line
containing this spinlock on other CPUS. So other threads doing
read()/write()/... calls that use RCU to access the file table are going
to ask further memory (possibly NUMA) transactions to read again this
memory line.
Move the spinlock to another cache line, so that concurrent threads can
share the cache line containing 'count' and 'fdt' fields.
It's worth up to 9% on a microbenchmark using a 4-thread 2-package x86
machine. See
http://marc.theaimsgroup.com/?l=linux-kernel&m=112680448713342&w=2
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Richard Purdie
Add a driver for the extra GPIOs found on the Sharp SL-C1000 (Akita).
These GPIOs are found on a Maxim MAX7310 I2C i/o expander chip. A
generic GPIO driver for the MAX7310 was attempted but this mini
driver is a much simpler and much more effective solution avoiding
several issues and complexity the generic driver had (as discussed
on LKML).
The platform device is required so the device parent can be set
correctly which ensures the device is one of the last to suspend
and first to resume. Whilst the i2c suspend/resume calls can be
influenced, nothing guarantees this is easlier/later than the
subsystems the gpios are used on which are all independent of i2c
(sound, irda, video/backlight etc.).
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On Fri, Nov 11, 2005 at 12:58:40PM -0800, David S. Miller wrote:
>
> This change:
>
> diff-tree 8ca2bdc7a9 (from feee207e44d3643d19e648aAuthor: Christoph Hellwig <hch@lst.de>
> Date: Wed Nov 9 12:07:18 2005 -0800
>
> [SPARC] sbus rtc: implement ->compat_ioctl
>
> Signed-off-by: Christoph Hellwig <hch@lst.de>
> Signed-off-by: David S. Miller <davem@davemloft.net>
>
> results in the console now getting spewed on sparc64 systems
> with messages like:
>
> [ 11.968298] ioctl32(hwclock:464): Unknown cmd fd(3) cmd(401c7014){00} arg(efc
> What's happening is hwclock tries first the SBUS rtc device ioctls
> then the normal rtc driver ones.
>
> So things actually worked better when we had the SBUS rtc compat ioctl
> directly handled via the generic compat ioctl code.
>
> There are _so_ many rtc drivers in the kernel implementing the
> generic rtc ioctls that I don't think putting a ->compat_ioctl
> into all of them to fix this problem is feasible. Unless we
> write a single rtc_compat_ioctl(), export it to modules, and hook
> it into all of those somehow.
>
> But even that doesn't appear to have any pretty implementation.
>
> Any better ideas?
We had similar problems with other ioctls where userspace did things
like that. What we did there was to put the compat handler to generic
code. The patch below does that, adding a big comment about what's
going on and removing the COMPAT_IOCTL entires for these on powerpc
that not only weren't ever useful but are duplicated now aswell.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Patch from Richard Purdie
Add the core machine support for the Sharp SL-C1000 (Akita)
and enable the Kconfig selection for it.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds request_queue->nr_sorted which keeps the number of
requests in the iosched and implement elv_drain_elevator which
performs forced dispatching. elv_drain_elevator checks whether
iosched actually dispatches all requests it has and prints error
message if it doesn't. As buggy forced dispatching can result in
wrong barrier operations, I think this extra check is worthwhile.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jens Axboe <axboe@suse.de>
Also introduces a sysctl option to configure the receive buffer
accounting policy to be either at socket or association level.
Default is all the associations on the same socket share the
receive buffer.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On ia64, it is possible to get NaT Consumption Fault and a kernel panic
when initializing sctp sideeffect commands arguments. The union
sctp_arg_t contains different sized elements and when loading a smaller
sized element (32 or 16 bits), it is possible for a speculative load to
fail and result in a NaT bit set which causes a kernel crash. The easy
way to get around it is to load the largerst member of the union.
Signed-off-by: Vladislav Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The socket level timeout values are maintained in sctp_sock and
association level timeouts are in sctp_association. So there is
no need for ep->timeouts.
Signed-off-by: Vladislav Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces 4-level page tables to ia64. I have run
some benchmarks and found nothing interesting. Performance has
consistently fallen within the noise range.
It also introduces a config option (setting the default to 3
levels). The config option prevents having 4 level page
tables with 64k base page size.
Signed-off-by: Robin Holt <holt@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This will let me chop the code size of several drivers right down. In
many cases the actual private data is very useful and constant for a
given host controller so being able to just pass it at probe time would
be very useful indeed (eg with the via driver would could pass the udma
clocking and reduce the code size, or with the AMD one the UDMA
multiplier and the offset)
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch moves the vdso's to arch/powerpc, adds support for the 32
bits vdso to the 32 bits kernel, rename systemcfg (finally !), and adds
some new (still untested) routines to both vdso's: clock_gettime() with
support for CLOCK_REALTIME and CLOCK_MONOTONIC, clock_getres() (same
clocks) and get_tbfreq() for glibc to retreive the timebase frequency.
Tom,Steve: The implementation of get_tbfreq() I've done for 32 bits
returns a long long (r3, r4) not a long. This is such that if we ever
add support for >4Ghz timebases on ppc32, the userland interface won't
have to change.
I have tested gettimeofday() using some glibc patches in both ppc32 and
ppc64 kernels using 32 bits userland (I haven't had a chance to test a
64 bits userland yet, but the implementation didn't change and was
tested earlier). I haven't tested yet the new functions.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Since the udbg code in ppc64 has no ppc32 equivalent, move it straight
over into arch/powerpc (and include/asm-powerpc for udbg.h). In time,
we probably want to meld the various bits and pieces of 32-bit early
debugging code into udbg, but for now only include it on
CONFIG_PPC64=y builds. The only change during the move is to
standardise the protecting #ifdef/#define in udbg.h, and move its
banner comment above the initial #ifdef (which seems to be normal
practice).
Built and booted on POWER5 LPAR (ARCH=powerpc and ARCH=ppc64). Built
for 32bit multiplatform (ARCH=powerpc).
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The definitions in sparsemem.h arent sufficient. We currently sell
machines with 2TB of RAM, and in order to give us room for a few years
growth lets set it to 16TB.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Convert to sparsemem and remove all the discontigmem code in the
process. This has a few advantages:
- The old numa_memory_lookup_table can go away
- All the arch specific discontigmem magic can go away
We also remove the triple pass of memory properties and instead create a
list of per node extents that we iterate through. A final cleanup would
be to change our lmb code to store extents per node, then we can reuse
that information in the numa code.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Remove ppc64 specific version of nr_cpus_node and use the generic one
provided.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Remove an unused numa define and move a discontigmem specific define
inside the relevant ifdef.
I will submit a separate patch to remove them from other architectures,
but the ppc64 patches to follow depend on this.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The bit position in the status register corresponding to the
PCI DMA interrupt was incorrect. Additionally, we did not
have a define for the PCI DMA interrupt.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
On Alpha:
include/linux/libata.h: In function `ata_pad_alloc':
include/linux/libata.h:785: warning: implicit declaration of function `dma_alloc_coherent'
include/linux/libata.h:786: warning: assignment makes pointer from integer without a cast
include/linux/libata.h: In function `ata_pad_free':
include/linux/libata.h:792: warning: implicit declaration of function `dma_free_coherent'
(I have a decouple-some-header-files cleanup in -mm, so it's causing some
fallout of this nature)
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Use "hints" to speed up the SACK processing. Various forms
of this have been used by TCP developers (Web100, STCP, BIC)
to avoid the 2x linear search of outstanding segments.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is an updated version of the RFC3465 ABC patch originally
for Linux 2.6.11-rc4 by Yee-Ting Li. ABC is a way of counting
bytes ack'd rather than packets when updating congestion control.
The orignal ABC described in the RFC applied to a Reno style
algorithm. For advanced congestion control there is little
change after leaving slow start.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move all the code that does linear TCP slowstart to one
inline function to ease later patch to add ABC support.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
TCP peformance with TSO over networks with delay is awful.
On a 100Mbit link with 150ms delay, we get 4Mbits/sec with TSO and
50Mbits/sec without TSO.
The problem is with TSO, we intentionally do not keep the maximum
number of packets in flight to fill the window, we hold out to until
we can send a MSS chunk. But, we also don't update the congestion window
unless we have filled, as per RFC2861.
This patch replaces the check for the congestion window being full
with something smarter that accounts for TSO.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
MSI hardcoded delivery mode to use logical delivery mode. Recently
x86_64 moved to use physical mode addressing to support physflat mode.
With this mode enabled noticed that my eth with MSI werent working.
msi_address_init() was hardcoded to use logical mode for i386 and x86_64.
So when we switch to use physical mode, things stopped working.
Since anyway we dont use lowest priority delivery with MSI, its always
directed to just a single CPU. Its safe and simpler to use
physical mode always, even when we use logical delivery mode for IPI's
or other ioapic RTE's.
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A nice feature of sysfs is that it can create the symlink from the
driver to the module that is contained in it.
It requires that the device_driver.owner is set, what is not the
case for many PCI drivers.
This patch allows pci_register_driver to set automatically the
device_driver.owner for any PCI driver.
Credits to Al Viro who suggested the method.
Signed-off-by: Laurent Riffard <laurent.riffard@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
--
drivers/ide/setup-pci.c | 12 +++++++-----
drivers/pci/pci-driver.c | 9 +++++----
include/linux/ide.h | 3 ++-
include/linux/pci.h | 10 ++++++++--
4 files changed, 22 insertions(+), 12 deletions(-)
This patch tweaks the way pciehp requests control of the hotplug
hardware from BIOS. It now tries to invoke the ACPI _OSC method
for a specific hotplug controller only, rather than walking the
entire acpi namespace invoking all possible _OSC methods under
all host bridges. This allows us to gain control of each hotplug
controller individually, even if BIOS fails to give us control of
some other hotplug controller in the system.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some devices have more than one capability of the same type. For
example, the PCI header for the PathScale InfiniPath looks like:
04:01.0 InfiniBand: Unknown device 1fc1:000d (rev 02)
Subsystem: Unknown device 1fc1:000d
Flags: bus master, fast devsel, latency 0, IRQ 193
Memory at fea00000 (64-bit, non-prefetchable) [size=2M]
Capabilities: [c0] HyperTransport: Slave or Primary Interface
Capabilities: [f8] HyperTransport: Interrupt Discovery and Configuration
There are _two_ HyperTransport capabilities, and the PathScale driver
wants to look at both of them.
The current pci_find_capability() API doesn't work for this, since it
only allows us to get to the first capability of a given type. The
patch below introduces a new pci_find_next_capability(), which can be
used in a loop like
for (pos = pci_find_capability(pdev, <ID>);
pos;
pos = pci_find_next_capability(pdev, pos, <ID>)) {
/* ... */
}
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The protocol field in ethernet headers is big-endian and should be
annotated as such. This patch allows detection of missing ntohs() calls
on the ethernet protocol field when sparse is run with __CHECK_ENDIAN__
defined.
This is a revised version that includes <linux/types.h> so that the
userspace programs are not confused by __be16. Thanks to David S.
Miller.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here is the patch that introduces the generic skb_checksum_complete
which also checks for hardware RX checksum faults. If that happens,
it'll call netdev_rx_csum_fault which currently prints out a stack
trace with the device name. In future it can turn off RX checksum.
I've converted every spot under net/ that does RX checksum checks to
use skb_checksum_complete or __skb_checksum_complete with the
exceptions of:
* Those places where checksums are done bit by bit. These will call
netdev_rx_csum_fault directly.
* The following have not been completely checked/converted:
ipmr
ip_vs
netfilter
dccp
This patch is based on patches and suggestions from Stephen Hemminger
and David S. Miller.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the computation of QP capabilities (max scatter/gather entries,
max inline data, etc) into the kernel, and have the uverbs module
return the values as part of the create QP response. This keeps
precise knowledge of device limits in the low-level kernel driver.
This requires an ABI bump, so while we're making changes, get rid of
the max_sge parameter for the modify SRQ command -- it's not used and
shouldn't be there.
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Change the struct ib_device.resize_cq() method to take a plain integer
that holds the new CQ size, rather than a pointer to an integer that
it uses to return the new size. This makes the interface match the
exported ib_resize_cq() signature, and allows the low-level driver to
update the CQ size with proper locking if necessary.
No in-tree drivers are exporting this method yet.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Patch from Liam Girdwood
This patch allows users of the pxa SSP driver to register their own irq
handlers instead of using the default SSP handler. It also cleans up the
CKEN clock and irq detection as the values are now stored in a table.
This patch replaces 2845/1
Changes:-
o Added flags parameter to ssp_init()
o Added SSP_NO_IRQ flag to disable registering of ssp irq handler (for
drivers that want to register their own handler)
o Cleaned up clock and irq detection, values are now stored in table.
o Added build changes to allow other drivers (e.g audio) to select the
ssp driver.
o corgi_ssp.c changed to use new interface.
Signed-off-by: Liam Girdwood <liam.girdwood@wolfsonmicro.com>
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
This patch adds a power and battery management core driver which with
the addition of the right device files, supports the c7x0 and cxx00
series of Sharp Zaurus handhelds.
The driver is complex for several reasons. Battery charging is manually
monitored and controlled. When suspended, the device needs to
periodically partially resume, check the charging status and then
re-suspend. It does without bothering the higher linux layers as
a full resume and re-suspend is unnecessary. The code is carefully
written to avoid interrupts or calling code outside the module under
these circumstances. It also vets the various wake up sources and
monitors the device's power situation.
Hooks to limit the backlight intensity and to notify the battery
monitoring code of backlight events are connected/added as the
backlight is one of the biggest users of power on the device.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Tony Lindgren
This patch updates omap H2 defconfig.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Tony Lindgren
This patch syncs the mainline kernel with linux-omap tree.
This patch contains changes to common header files for
omap1xxx and omap24xx by various omap developers, and
improved cpu detection by Imre Deak
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Alessandro Zummo
This patch adds support for the LinkSys NSLU2 running with
both big and little-endian kernels. The LinkSys NSLU2 is
a cost engineered ARM, XScale 420 based system similar to
the the Intel IXDP425 evaluation board. It uses the
IXP4XX ARCH.
While this patch applies independently of other patches
the resultant kernel requires further patches to successfully
use onboard devices, including the onboard flash. Since these
patches are independent of this one they will be submitted
separately.
A defconfig is not included here because not all of
the required drivers are actually in the kernel.
We intend to provide one as soon as the patches
will be incorporated in mainstream.
This patch is the combined work of nslu2-linux.org
Signed-off-by: John Bowler <jbowler@acm.org>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
For now, we need these declarations that we moved from C code in
the asm-ppc64 versions of these headers as well as the asm-powerpc
versions. The asm-ppc64 versions will be disappearing shortly.
Signed-off-by: Paul Mackerras <paulus@samba.org>
17-eeh-slot-marking-bug.patch
A device that experiences a PCI outage may be just one deivce out
of many that was affected. In order to avoid repeated reports of
a failure, the entire tree of affected devices should be marked
as failed. This patch marks up the entire tree.
Signed-off-by: Linas Vepstas <linas@linas.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This also make klimit have the same type on 32-bit as on 64-bit,
namely unsigned long, and defines and initializes it in one place.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch moves a bunch more files from arch/ppc64 and
include/asm-ppc64 which have no equivalents in ppc32 code into
arch/powerpc and include/asm-powerpc. The file affected are:
hvcall.h
proc_ppc64.c
sysfs.c
lparcfg.c
rtas_pci.c
The only changes apart from the move and corresponding Makefile
changes are:
- #ifndef/#define in includes updated to _ASM_POWERPC_ form
- trailing whitespace removed
- comments giving full paths removed
Built and booted on POWER5 LPAR (ARCH=powerpc and ARCH=ppc64), built
for 32-bit powermac (ARCH=powerpc).
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch makes the kernel use a different kmem cache for PMD pages
as they are smaller than PTE pages. Avoids waste of memory.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is at the request of the glibc folks, who want to use these bits
to select libraries optimized for the microarchitecture and new
instructions in these processors.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch merges platform codes. systemcfg->platform is no longer used,
systemcfg use in general is deprecated as much as possible (and renamed
_systemcfg before it gets completely moved elsewhere in a future patch),
_machine is now used on ppc64 along as ppc32. Platform codes aren't gone
yet but we are getting a step closer. A bunch of asm code in head[_64].S
is also turned into C code.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch consolidates macros used to generate assembly for
compatibility across different CPUs or configs. A new header,
asm-powerpc/asm-compat.h contains the main compatibility macros. It
uses some preprocessor magic to make the macros suitable both for use
in .S files, and in inline asm in .c files. Headers (bitops.h,
uaccess.h, atomic.h, bug.h) which had their own such compatibility
macros are changed to use asm-compat.h.
ppc_asm.h is now for use in .S files *only*, and a #error enforces
that. As such, we're a lot more careless about namespace pollution
here than in asm-compat.h.
While we're at it, this patch adds a call to the PPC405_ERR77 macro in
futex.h which should have had it already, but didn't.
Built and booted on pSeries, Maple and iSeries (ARCH=powerpc). Built
for 32-bit powermac (ARCH=powerpc) and Walnut (ARCH=ppc).
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The ppc32 and ppc64 versions of cacheflush.h were almost identical.
The two versions of cache.h are fairly similar, except for a bunch of
register definitions in the ppc32 version which probably belong better
elsewhere. This patch, therefore, merges both headers. Notable
points:
- there are several functions in cacheflush.h which exist only
on ppc32 or only on ppc64. These are handled by #ifdef for now, but
these should probably be consolidated, along with the actual code
behind them later.
- Confusingly, both ppc32 and ppc64 have a
flush_dcache_range(), but they're subtly different: it uses dcbf on
ppc32 and dcbst on ppc64, ppc64 has a flush_inval_dcache_range() which
uses dcbf. These too should be merged and consolidated later.
- Also flush_dcache_range() was defined in cacheflush.h on
ppc64, and in cache.h on ppc32. In the merged version it's in
cacheflush.h
- On ppc32 flush_icache_range() is a normal function from
misc.S. On ppc64, it was wrapper, testing a feature bit before
calling __flush_icache_range() which does the actual flush. This
patch takes the ppc64 approach, which amounts to no change on ppc32,
since CPU_FTR_COHERENT_ICACHE will never be set there, but does mean
renaming flush_icache_range() to __flush_icache_range() in
arch/ppc/kernel/misc.S and arch/powerpc/kernel/misc_32.S
- The PReP register info from asm-ppc/cache.h has moved to
arch/ppc/platforms/prep_setup.c
- The 8xx register info from asm-ppc/cache.h has moved to a
new asm-powerpc/reg_8xx.h, included from reg.h
- flush_dcache_all() was defined on ppc32 (only), but was
never called (although it was exported). Thus this patch removes it
from cacheflush.h and from ARCH=powerpc (misc_32.S) entirely. It's
left in ARCH=ppc for now, with the prototype moved to ppc_ksyms.c.
Built for Walnut (ARCH=ppc), 32-bit multiplatform (pmac, CHRP and PReP
ARCH=ppc, pmac and CHRP ARCH=powerpc). Built and booted on POWER5
LPAR (ARCH=powerpc and ARCH=ppc64).
Built for 32-bit powermac (ARCH=ppc and ARCH=powerpc). Built and
booted on POWER5 LPAR (ARCH=powerpc and ARCH=ppc64). Built and booted
on G5 (ARCH=powerpc)
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The generic netlink family builds on top of netlink and provides
simplifies access for the less demanding netlink users. It solves
the problem of protocol numbers running out by introducing a so
called controller taking care of id management and name resolving.
Generic netlink modules register themself after filling out their
id card (struct genl_family), after successful registration the
modules are able to register callbacks to command numbers by
filling out a struct genl_ops and calling genl_register_op(). The
registered callbacks are invoked with attributes parsed making
life of simple modules a lot easier.
Although generic netlink modules can request static identifiers,
it is recommended to use GENL_ID_GENERATE and to let the controller
assign a unique identifier to the module. Userspace applications
will then ask the controller and lookup the idenfier by the module
name.
Due to the current multicast implementation of netlink, the number
of generic netlink modules is restricted to 1024 to avoid wasting
memory for the per socket multiacst subscription bitmask.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduces netlink_run_queue() to handle the receive queue of
a netlink socket in a generic way. Processes as much as there
was in the queue upon entry and invokes a callback function
for each netlink message found. The callback function may
refuse a message by returning a negative error code but setting
the error pointer to 0 in which case netlink_run_queue() will
return with a qlen != 0.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduces a new type-safe interface for netlink message and
attributes handling. The interface is fully binary compatible
with the old interface towards userspace. Besides type safety,
this interface features attribute validation capabilities,
simplified message contstruction, and documentation.
The resulting netlink code should be smaller, less error prone
and easier to understand.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The existing connection tracking subsystem in netfilter can only
handle ipv4. There were basically two choices present to add
connection tracking support for ipv6. We could either duplicate all
of the ipv4 connection tracking code into an ipv6 counterpart, or (the
choice taken by these patches) we could design a generic layer that
could handle both ipv4 and ipv6 and thus requiring only one sub-protocol
(TCP, UDP, etc.) connection tracking helper module to be written.
In fact nf_conntrack is capable of working with any layer 3
protocol.
The existing ipv4 specific conntrack code could also not deal
with the pecularities of doing connection tracking on ipv6,
which is also cured here. For example, these issues include:
1) ICMPv6 handling, which is used for neighbour discovery in
ipv6 thus some messages such as these should not participate
in connection tracking since effectively they are like ARP
messages
2) fragmentation must be handled differently in ipv6, because
the simplistic "defrag, connection track and NAT, refrag"
(which the existing ipv4 connection tracking does) approach simply
isn't feasible in ipv6
3) ipv6 extension header parsing must occur at the correct spots
before and after connection tracking decisions, and there were
no provisions for this in the existing connection tracking
design
4) ipv6 has no need for stateful NAT
The ipv4 specific conntrack layer is kept around, until all of
the ipv4 specific conntrack helpers are ported over to nf_conntrack
and it is feature complete. Once that occurs, the old conntrack
stuff will get placed into the feature-removal-schedule and we will
fully kill it off 6 months later.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
14-eeh-device-bar-save.patch
After a PCI device has been resest, the device BAR's and other config
space info must be restored to the same state as they were in when
the firmware first handed us this device. This will allow the
PCI device driver, when restarted, to correctly recognize and set up
the device.
Tis patch saves the device config space as early as reasonable after
the firmware has handed over the device. Te state resore funcion
is inteded for use by the EEH recovery routines.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
13-eeh-recovery-support-routines.patch
EEH Recovery support routines
This patch adds routines required to help drive the recovery of
EEH-frozen slots. The main function is to drive the PCI #RST
signal line high for a qurter of a second, and then allow for
a second & a half of settle time.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
12-eeh-event-dispatcher.patch
ppc64: EEH Recovery dispatcher thread
This patch adds a mechanism to create recovery threads when an
EEH event is received. Since an EEH freeze state may be detected
within an interrupt context, we need to get out of the interrupt
context before starting recovery. This dispatcher does this in
two steps: first, it uses a workqueue to get out, and then
lanuches a kernel thread, so that the recovery routine can
sleep for exteded periods without upseting the keventd.
A kernel thread is created with each EEH event, rather than
having one long-running daemon started at boot time. This is
because it is anticipated that EEH events will be very rare
(very very rare, ideally) and so its pointless to cluter the
process tables with a daemon that will almost never run.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
10-EEH-enable-bugfix.patch
Bugfix: With the curent linux-2.6.14-rc2-git6, EEH errors are
ignored because thier detection requires an unused, uninitialized
flag to be set. This patch removes the unused flag.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
03-eeh-addr-cache-cleanup.patch
This is a minor patch to clean up a buglet related to the PCI address cache.
(The buglet doesn't manifes itself unless there are also bugs elsewhere,
which is why its minor.). Also:
-- Improved debug printing.
-- Declare some private routines as static
-- Adds reference counting to struct pci_dn->pcidev structure
Signed-off-by: Linas Vepstas <linas@linas.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
01-pci-dn-uniformization.patch
This patch changes the rtas_pci interface to use the new struct pci_dn
structure for two routines that work with pci device nodes.
This patch also does some minor janitorial work: it uses some handy macros
and cleans up some trailing whitespace in the affected file.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch moves a bunch of files from arch/ppc64 and
include/asm-ppc64 which have no equivalents in ppc32 code into
arch/powerpc and include/asm-powerpc. The file affected are:
abs_addr.h
compat.h
lppaca.h
paca.h
tce.h
cpu_setup_power4.S
ioctl32.c
firmware.c
pacaData.c
The only changes apart from the move and corresponding Makefile
changes are:
- #ifndef/#define in includes updated to _ASM_POWERPC_ form
- trailing whitespace removed
- comments giving full paths removed
- pacaData.c renamed paca.c to remove studlyCaps
- Misplaced { moved in lppaca.h
Built and booted on POWER5 LPAR (ARCH=powerpc and ARCH=ppc64), built
for 32-bit powermac (ARCH=powerpc).
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch merges current.h. This is a one-big-ifdef merge, but both
versions are so tiny, I think we can live with it. While we're at it,
we get rid of the fairly pointless redirection through get_current()
in the ppc64 version.
Built and booted on POWER5 LPAR (ARCH=powerpc & ARCH=ppc64). Built
for 32-bit pmac (ARCH=powerpc & ARCH=ppc).
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Having already merged the ppc and ppc64 versions of signal.c, this
patch finishes the job by merging signal.h. The two versions were
almost identical already. Notable changes:
- We use BITS_PER_LONG to correctly size sigset_t
- Remove some uneeded #includes and struct forward
declarations. This does mean adding an include to signal_32.c which
relied on the indirect inclusion of sigcontext.h
- As the ppc64 version, the merged signal.h has prototypes for
do_signal() and do_signal32(). Thus remove extra prototypes from
ppc_ksyms.c which had them directly.
Built and booted on POWER5 LPAR (ARCH=ppc64 and ARCH=powerpc). Built
for 32-bit powermac (ARCH=ppc and ARCH=powerpc) and Walnut (ARCH=ppc).
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Matthew Wilcox asked that this got a comment explaining why it is done
so here it is.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
From: "Jordan Crouse" <jordan.crouse@amd.com>
The core IDE engine on the CS5536 is the same as the other AMD southbridges,
so unlike the CS5535, we can simply add the appropriate PCI headers to
the existing amd74xx code.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
CONFIG_IDE_MAX_HWIFS is a generic thing, no need to have it duplicated
by every arch that uses it.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Devices driven by ide-cs will appear under /sys/devices instead of the
appropriate PCMCIA device. To fix this I had to extend the hw_regs_t
structure with a 'struct device' field, which allows us to set the
parent link for the appropriate hwif.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Jens Axboe <axboe@suse.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
nfattr_parse (and thus nfattr_parse_nested) always returns success. So we
can make them 'void' and remove all the checking at the caller side.
Based on original patch by Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce struct platform_driver. This allows the platform device
driver methods to be passed a platform_device structure instead of
instead of a plain device structure, and therefore requiring casting
in every platform driver.
We introduce this in such a way that any existing platform drivers
registered directly via driver_register continue to work as before,
thereby allowing a gradual conversion to the new platform_driver
methods.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
There are a few loose ends following the conversion of md to use kthreads:
- Some fields in mdk_thread_t that aren't needed (kthreads does it's own
completion and manages it's own name).
- thread->run is now never NULL, so no need to check
- Some tests for signal_pending that aren't needed (As we don't use signals
to stop threads any more)
- Some flush_signals are not needed
- Some waits are interruptible and don't need to be.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We can only accept BARRIER requests if all slaves handle
barriers, and that can, of course, change with time....
So we keep track of whether the whole array seems safe for barriers,
and also whether each individual rdev handles barriers.
We initially assumes barriers are OK.
When writing the superblock we try a barrier, and if that fails, we flag
things for no-barriers. This will usually clear the flags fairly quickly.
If writing the superblock finds that BIO_RW_BARRIER is -ENOTSUPP, we need to
resubmit, so introduce function "md_super_wait" which waits for requests to
finish, and retries ENOTSUPP requests without the barrier flag.
When writing the real raid1, write requests which were BIO_RW_BARRIER but
which aresn't supported need to be retried. So raid1d is enhanced to do this,
and when any bio write completes (i.e. no retry needed) we remove it from the
r1bio, so that devices needing retry are easy to find.
We should hardly ever get -ENOTSUPP errors when writing data to the raid.
It should only happen if:
1/ the device used to support BARRIER, but now doesn't. Few devices
change like this, though raid1 can!
or
2/ the array has no persistent superblock, so there was no opportunity to
pre-test for barriers when writing the superblock.
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Current bitmaps use set_bit et.al and so are host-endian, which means
not-portable. Oops.
Define a new version number (4) for which bitmaps are little-endian.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This has the advantage of removing the confusion caused by 'rdev_t' and
'mddev_t' both having 'in_sync' fields.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Two refinements to the 'attempt-overwrite-on-read-error' mechanism.
1/ If the array is read-only, don't attempt an over-write.
2/ If there are more than max_nr_stripes read errors on a device with
no success, fail the drive. This will make sure a dead
drive will be eventually kicked even when we aren't trying
to rewrite (which would normally kick a dead drive more quickly.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There isn't really a need for raid5 attributes to be an a subdirectory,
so this patch moves them from
/sys/block/mdX/md/raid5/attribute
to
/sys/block/mdX/md/attribute
This suggests that all md personalities should co-operate about
namespace usage, but that shouldn't be a problem.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
With this, raid5 can be asked to check parity without repairing it. It also
keeps a count of the number of incorrect parity blocks found (mismatches) and
reports them through sysfs.
Signed-off-by: Neil Brown <neilb@suse.de>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
You can trigger a 'check' with
echo check > /sys/block/mdX/md/scan_mode
or a check-and-repair errors with
echo repair > /sys/block/mdX/md/scan_mode
and read the current state from the same file.
Note: personalities need to know the different between 'check' and 'repair',
but don't yet. Until they do, 'check' will be the same as 'repair' and will
just do a normal resync pass.
Signed-off-by: Neil Brown <neilb@suse.de>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
/sys/block/mdX/md/raid5/
contains raid5-related attributes.
Currently
stripe_cache_size
is number of entries in stripe cache, and is settable.
stripe_cache_active
is number of active entries, and in only readable.
Signed-off-by: Neil Brown <neilb@suse.de>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Each device in an md array how has a corresponding
/sys/block/mdX/md/devNN/
directory which can contain attributes. Currently there is only 'state' which
summarises the state, nd 'super' which has a copy of the superblock, and
'block' which is a symlink to the block device.
Also, /sys/block/mdX/md/rdNN represents slot 'NN' in the array, and is a
symlink to the relevant 'devNN'. Obviously spare devices do not have a slot
in the array, and so don't have such a symlink.
Signed-off-by: Neil Brown <neilb@suse.de>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Start using kobjects in mddevs, and provide a couple of simple attributes
(level and disks). Attributes live in
/sys/block/mdX/md/attr-name
Signed-off-by: Neil Brown <neilb@suse.de>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch changes the behaviour of raid5 when it gets a read error.
Instead of just failing the device, it tried to find out what should have
been there, and writes it over the bad block. For some media-errors, this
has a reasonable chance of fixing the error. If the write succeeds, and a
subsequent read succeeds as well, raid5 decided the address is OK and
conitnues.
Instead of failing a drive on read-error, we attempt to re-write the block,
and then re-read. If that all works, we allow the device to remain in the
array.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The frame buffer layer already had some code dealing with compat ioctls, this
patch moves over the remaining code from fs/compat_ioctl.c
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add ability to set rotation via sysfs. The attributes are located in
/sys/class/graphics/fb[n] and accepts 0 - unrotated; 1 - clockwise; 2 - upside
down; 3 - counterclockwise.
The attributes are:
con_rotate (r/w) - set rotation of the active console
con_rotate_all (w) - set rotation of all consoles
rotate (r/w) - set rotation of the framebuffer, if supported.
Currently, none of the drivers support this.
This is probably temporary, since con_rotate and con_rotate_all are
console-specific and has no business being under the fb device. However,
until the console layer acquires it's own sysfs class, these attributes will
temporarily reside here.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support for rotating and positioning of the logo. Rotation and position
depends on 'int rotate' parameter added to fb_prepare_logo() and
fb_show_logo().
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch series implements generic code to rotate the console at 90, 180,
and 270 degrees. The implementation is completely done in the framebuffer
console level, thus no changes to the framebuffer layer or to the drivers
are needed.
Console rotation is required by some Sharp-based devices where the natural
orientation of the display is not at 0 degrees. Also, users that have
displays that can pivot will benefit by having a console in portrait mode
if they so desire.
The choice to implement the code in the console layer rather than in the
framebuffer layer is due to the following reasons:
- it's fast
- it does not require driver changes
- it can coexist with devices that can rotate the display at the hardware level
- it complements graphics applications that can do display rotation
The changes to core fbcon are minimal-- recognition of the console
rotation angle so it can swap directions, origins and axes (xres vs yres,
xpanstep vs ypanstep, xoffset vs yoffset, etc) and storage of the rotation
angle per display. The bulk of the code that does the actual drawing to the
screen are placed in separate files. Each angle of rotation has separate
methods (bmove, clear, putcs, cursor, update_start which is derived from
update_var, and clear_margins). To mimimize processing time, the fontdata
are pre-rotated at each console switch (only if the font or the angle has
changed).
The option can be compiled out (CONFIG_FRAMEBUFFER_CONSOLE_ROTATION = n) if
rotation is not needed.
Choosing the rotation angle can be done in several ways:
1. boot option fbcon=rotate:n, where
n = 0 - normal
n = 1 - 90 degrees (clockwise)
n = 2 - 180 degrees (upside down)
n = 3 - 270 degrees (counterclockwise)
2. echo n > /sys/class/graphics/fb[num]/con_rotate
where n is the same as described above. It sets the angle of rotation
of the current console
3 echo n > /sys/class/graphics/fb[num]/con_rotate_all
where n is the same as described above. Globally sets the angle of
rotation.
GOTCHAS:
The option, especially at angles of 90 and 270 degrees, will exercise
the least used code of drivers. Namely, at these angles, panning is done
in the x-axis, so it can reveal bugs in the driver if xpanstep is set
incorrectly. A workaround is to set xpanstep = 0.
Secondly, at these angles, the framebuffer memory access can be
unaligned if (fontheight * bpp) % 32 ~= 0 which can reveal bugs in the drivers
imageblit, fillrect and copyarea functions. (I think cfbfillrect may have
this buglet). A workaround is to use a standard 8x16 font.
Speed:
The scrolling speed difference between 0 and 180 degrees is minimal,
somewhere areound 1-2%. At 90 or 270 degress, speed drops down to a vicinity
of 30-40%. This is understandable because the blit direction is across the
framebuffer "direction." Scrolling will be helped at these angles if xpanstep
is not equal to zero, use of 8x16 fonts, and setting xres_virtual >= xres * 2.
Note: The code is tested on little-endian only, so I don't know if it will
work in big-endian. Please let me know, it will take only less than a minute
of your time.
This patch prepares fbcon for console rotation and contains the following
changes:
- add rotate field in struct fbcon_ops to keep fbcon's current rotation
angle
- add con_rotate field in struct display to store per-display rotation angle
- create a private copy of the current var to fbcon. This will prevent
fbcon from directly manipulating info->var, especially the fields xoffset,
yoffset and vmode.
- add ability to swap pertinent axes (xres, yres; xpanstep, ypanstep; etc)
depending on the rotation angle
- change global update_var() (function that sets the screen start address)
as an fbcon method update_start. This is required because the axes, start
offset, and/or direction can be reversed depending on the rotation angle.
- add fbcon method rotate_font() which will rotate each character bitmap to
the correct angle of rotation.
- add fbcon boot option 'rotate' to select the angle of rotation at bootime.
Currently does nothing until all patches are applied.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Em28xx cleanups and fixes.
- Some cleanups and audio amux adjust.
- em28xx will allways try, by default, the biggest size alt.
- Fixes audio mux code.
- Fixes some logs.
- Adds support for digital output for WinTV USB2 board.
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Moved some user defines to be out of __KERNEL__ define.
Signed-off-by: Michael Schimek <mschimek@gmx.at>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Some changes to allow compiling cx88 and saa7134 without V4L1 support.
- This patch will help obsoleting V4L1 API.
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- This patch adds the VIDIOC_LOG_STATUS to videodev2.h and adds
LOG_STATUS support to tda9887.c and bttv-driver.c.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- New config option for tda9887 to specifically set intercarrier
Signed-off-by: Nickolay V. Shmyrev <nshmyrev@yandex.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Several Improvement on I2C IR handling for em2820:
- moved Pinnacle IR table (ir_codes_em2820) to em2820-input.c
- IR struct renamed and moved to a header file.
- New file to handle em2820-specific IR.
- Some cleanups.
- attach now detects I2C IR and calls em2820-specific IR code
- IR compat code moved to compat.h
- New header with struct IR_i2c there, to allow it to be
used by board-specific input handlers.
- Some improvements at em28xx board detection:
- Board detection message improved to show interface and class.
- Now it doesn't touch audio interfaces.
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Include newer I2C ID at ../linux/include/media/id.h:
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Added analog support for ATI HDTV Wonder
Signed-off-by: Kirk Lapray <kirk.lapray@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Set IF of tda8275 according to tv norm.
Signed-off-by: Nickolay V. Shmyrev <nshmyrev@yandex.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Update the tveeprom tuner list with the tuner
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Nickolay V. Shmyrev <nshmyrev@yandex.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
->permission and ->lookup have a struct nameidata * argument these days to
pass down lookup intents. Unfortunately some callers of lookup_hash don't
actually pass this one down. For lookup_one_len() we don't have a struct
nameidata to pass down, but as this function is a library function only
used by filesystem code this is an acceptable limitation. All other
callers should pass down the nameidata, so this patch changes the
lookup_hash interface to only take a struct nameidata argument and derives
the other two arguments to __lookup_hash from it. All callers already have
the nameidata argument available so this is not a problem.
At the same time I'd like to deprecate the lookup_hash interface as there
are better exported interfaces for filesystem usage. Before it can
actually be removed I need to fix up rpc_pipefs.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Ram Pai <linuxram@us.ibm.com>
Cc: Jeff Mahoney <jeffm@suse.com>
Cc: Al Viro <viro@ftp.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A few more callers of permission() just want to check for a different access
pattern on an already open file. This patch adds a wrapper for permission()
that takes a file in preparation of per-mount read-only support and to clean
up the callers a little. The helper is not intended for new code, everything
without the interface set in stone should use vfs_permission()
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Most permission() calls have a struct nameidata * available. This helper
takes that as an argument and thus makes sure we pass it down for lookup
intents and prepares for per-mount read-only support where we need a struct
vfsmount for checking whether a file is writeable.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch removes almost all inclusions of linux/version.h. The 3
#defines are unused in most of the touched files.
A few drivers use the simple KERNEL_VERSION(a,b,c) macro, which is
unfortunatly in linux/version.h.
There are also lots of #ifdef for long obsolete kernels, this was not
touched. In a few places, the linux/version.h include was move to where
the LINUX_VERSION_CODE was used.
quilt vi `find * -type f -name "*.[ch]"|xargs grep -El '(UTS_RELEASE|LINUX_VERSION_CODE|KERNEL_VERSION|linux/version.h)'|grep -Ev '(/(boot|coda|drm)/|~$)'`
search pattern:
/UTS_RELEASE\|LINUX_VERSION_CODE\|KERNEL_VERSION\|linux\/\(utsname\|version\).h
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fixes e500 build and cleans up traps.c by moving perf_irq extern to
pmc.h.
Signed-off-by: Matt Porter <mporter@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
MPC834x uses the gianfar network driver which now uses the new phylib. We
need to update the platform code to create a gianfar platform MDIO bus and
pass the right intializations to the gianfar driver to make things work
again.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When calling target drivers to set frequency, we take cpucontrol lock.
When we modified the code to accomodate CPU hotplug, there was an attempt
to take a double lock of cpucontrol leading to a deadlock. Since the
current thread context is already holding the cpucontrol lock, we dont need
to make another attempt to acquire it.
Now we leave a trace in current->flags indicating current thread already is
under cpucontrol lock held, so we dont attempt to do this another time.
Thanks to Andrew Morton for the beating:-)
From: Brice Goglin <Brice.Goglin@ens-lyon.org>
Build fix
(akpm: this patch is still unpleasant. Ashok continues to look for a cleaner
solution, doesn't he? ;))
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Brice Goglin <Brice.Goglin@ens-lyon.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Kyungmin Park
This patch is required for OneNAND MTD to passing the OneNAND sync. burst read
Signed-off-by: Kyungmin Park
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
save_and_disable_irqs does not need to use mov + msr (which was
introduced to work around a documentation bug which was propagated
into binutils.) Use msr with an immediate constant, and if we're
building for ARMv6 or later, use the new CPSID instruction.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use __do_IRQ instead. The only difference is that every controller
is now assumed to have an end() routine (only xics_8259 did not).
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
You could open the /proc/sys/net/ipv4/conf/<if>/<whatever> file, then
wait for interface to go away, try to grab as much memory as possible in
hope to hit the (kfreed) ctl_table. Then fill it with pointers to your
function. Then do read from file you've opened and if you are lucky,
you'll get it called as ->proc_handler() in kernel mode.
So this is at least an Oops and possibly more. It does depend on an
interface going away though, so less of a security risk than it would
otherwise be.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
