Sierra Wireless MC7305/MC7355 with USB ID 1199:9041 also provide a
second QMI/network interface like the MC73xx with USB ID 1199:68c0 on
USB interface #10 when used in the appropriate USB configuration.
Add the corresponding QMI_FIXED_INTF entry to the qmi_wwan driver.
Please note that the second QMI/network interface is not working for
early MC73xx firmware versions like 01.08.x as the device does not
respond to QMI messages on the second /dev/cdc-wdm port.
Signed-off-by: Reinhard Speyerer <rspmn@arcor.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update referenced specs link to reflect actual file version and location.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NCM specs are not actually mandating a specific position in the frame for
the NDP (Network Datagram Pointer). However, some Huawei devices will
ignore our aggregates if it is not placed after the datagrams it points
to. Add support for doing just this, in a per-device configurable way.
While at it, update NCM subdrivers, disabling this functionality in all of
them, except in huawei_cdc_ncm where it is enabled instead.
We aren't making any distinction between different Huawei NCM devices,
based on what the vendor driver does. Standard NCM devices are left
unaffected: if they are compliant, they should be always usable, still
stay on the safe side.
This change has been tested and working with a Huawei E3131 device (which
works regardless of NDP position), a Huawei E3531 (also working both
ways) and an E3372 (which mandates NDP to be after indexed datagrams).
V1->V2:
- corrected wrong NDP acronym definition
- fixed possible NULL pointer dereference
- patch cleanup
V2->V3:
- Properly account for the NDP size when writing new packets to SKB
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This device is sold as 'NVIDIA Tegra USB 3.0 Ethernet'.
Chipset is RTL8153 and works with r8152.
Signed-off-by: Zheng Liu <zhliu@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tx_curr_frame_payload field is u32. When we try to calculate a
small negative delta based on it, we end up with a positive integer
close to 2^32 instead. So the tx_bytes pointer increases by about
2^32 for every transmitted frame.
Fix by calculating the delta as a signed long.
Cc: Ben Hutchings <ben.hutchings@codethink.co.uk>
Reported-by: Florian Bruhin <me@the-compiler.org>
Fixes: 7a1e890e21 ("usbnet: Fix tx_bytes statistic running backward in cdc_ncm")
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
transfer_buffer_length is of type u32. It's therefore wrong to assign it
to a signed integer. This patch avoids the overflow.
It's worth noting that entry->length here is a long; perhaps it would be
beneficial at somepoint to change this to be unsigned as well, if
nothing else relies on its signedness for error conditions or the like.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This device is sold as 'Lenovo OneLink Pro Dock'.
Chipset is RTL8153 and works with r8152.
Signed-off-by: Vasily Titskiy <qehgt0@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dwmac-socfpga.c conflict was a case of a bug fix overlapping
changes in net-next to handle an error pointer differently.
Signed-off-by: David S. Miller <davem@davemloft.net>
"kevent" is an extremely generic name that causes trouble
if debugging for work queues is used. So change it to
something clear.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/usb/asix_common.c
drivers/net/usb/sr9800.c
drivers/net/usb/usbnet.c
include/linux/usb/usbnet.h
net/ipv4/tcp_ipv4.c
net/ipv6/tcp_ipv6.c
The TCP conflicts were overlapping changes. In 'net' we added a
READ_ONCE() to the socket cached RX route read, whilst in 'net-next'
Eric Dumazet touched the surrounding code dealing with how mini
sockets are handled.
With USB, it's a case of the same bug fix first going into net-next
and then I cherry picked it back into net.
Signed-off-by: David S. Miller <davem@davemloft.net>
This device is sold as 'Lenovo Tinkpad USB 3.0 Ethernet 4X90E51405'.
Chipset is RTL8153 and works with r8152.
Signed-off-by: Christian Hesse <mail@eworm.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
cdc_ncm disagrees with usbnet about how much framing overhead should
be counted in the tx_bytes statistics, and tries 'fix' this by
decrementing tx_bytes on the transmit path. But statistics must never
be decremented except due to roll-over; this will thoroughly confuse
user-space. Also, tx_bytes is only incremented by usbnet in the
completion path.
Fix this by requiring drivers that set FLAG_MULTI_FRAME to set a
tx_bytes delta along with the tx_packets count.
Fixes: beeecd42c3 ("net: cdc_ncm/cdc_mbim: adding NCM protocol statistics")
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Currently the usbnet core does not update the tx_packets statistic for
drivers with FLAG_MULTI_PACKET and there is no hook in the TX
completion path where they could do this.
cdc_ncm and dependent drivers are bumping tx_packets stat on the
transmit path while asix and sr9800 aren't updating it at all.
Add a packet count in struct skb_data so these drivers can fill it
in, initialise it to 1 for other drivers, and add the packet count
to the tx_packets statistic on completion.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Tested-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/netfilter/nf_tables_core.c
The nf_tables_core.c conflict was resolved using a conflict resolution
from Stephen Rothwell as a guide.
Signed-off-by: David S. Miller <davem@davemloft.net>
When the device is powered up, some (older) firmware versions fail to work
properly if we send commands before the boot is complete (everything is OK
when the device is hot-plugged). The firmware indicates its ready status by
putting the link up.
Newer firmwares delay the first command so they don't suffer from this problem.
They also report the link being always up.
Wait for firmware to become ready (link up) before sending any commands and/or
data.
This also allows lowering CMD_TIMEOUT value to a reasonable time.
Tested with 4.1.0.9 (old) and 4.1.0.30 (new) firmware versions.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/emulex/benet/be_main.c
net/core/sysctl_net_core.c
net/ipv4/inet_diag.c
The be_main.c conflict resolution was really tricky. The conflict
hunks generated by GIT were very unhelpful, to say the least. It
split functions in half and moved them around, when the real actual
conflict only existed solely inside of one function, that being
be_map_pci_bars().
So instead, to resolve this, I checked out be_main.c from the top
of net-next, then I applied the be_main.c changes from 'net' since
the last time I merged. And this worked beautifully.
The inet_diag.c and sysctl_net_core.c conflicts were simple
overlapping changes, and were easily to resolve.
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 11ad714b98 because
it breaks cx82310_eth.
The custom USB_DEVICE_CLASS macro matches
bDeviceClass, bDeviceSubClass and bDeviceProtocol
but the common USB_DEVICE_AND_INTERFACE_INFO matches
bInterfaceClass, bInterfaceSubClass and bInterfaceProtocol instead, which are
not specified.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/rocker/rocker.c
The rocker commit was two overlapping changes, one to rename
the ->vport member to ->pport, and another making the bitmask
expression use '1ULL' instead of plain '1'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) If an IPVS tunnel is created with a mixed-family destination
address, it cannot be removed. Fix from Alexey Andriyanov.
2) Fix module refcount underflow in netfilter's nft_compat, from Pablo
Neira Ayuso.
3) Generic statistics infrastructure can reference variables sitting on
a released function stack, therefore use dynamic allocation always.
Fix from Ignacy Gawędzki.
4) skb_copy_bits() return value test is inverted in ip_check_defrag().
5) Fix network namespace exit in openvswitch, we have to release all of
the per-net vports. From Pravin B Shelar.
6) Fix signedness bug in CAIF's cfpkt_iterate(), from Dan Carpenter.
7) Fix rhashtable grow/shrink behavior, only expand during inserts and
shrink during deletes. From Daniel Borkmann.
8) Netdevice names with semicolons should never be allowed, because
they serve as a separator. From Matthew Thode.
9) Use {,__}set_current_state() where appropriate, from Fabian
Frederick.
10) Revert byte queue limits support in r8169 driver, it's causing
regressions we can't figure out.
11) tcp_should_expand_sndbuf() erroneously uses tp->packets_out to
measure packets in flight, properly use tcp_packets_in_flight()
instead. From Neal Cardwell.
12) Fix accidental removal of support for bluetooth in CSR based Intel
wireless cards. From Marcel Holtmann.
13) We accidently added a behavioral change between native and compat
tasks, wrt testing the MSG_CMSG_COMPAT bit. Just ignore it if the
user happened to set it in a native binary as that was always the
behavior we had. From Catalin Marinas.
14) Check genlmsg_unicast() return valud in hwsim netlink tx frame
handling, from Bob Copeland.
15) Fix stale ->radar_required setting in mac80211 that can prevent
starting new scans, from Eliad Peller.
16) Fix memory leak in nl80211 monitor, from Johannes Berg.
17) Fix race in TX index handling in xen-netback, from David Vrabel.
18) Don't enable interrupts in amx-xgbe driver until all software et al.
state is ready for the interrupt handler to run. From Thomas
Lendacky.
19) Add missing netlink_ns_capable() checks to rtnl_newlink(), from Eric
W Biederman.
20) The amount of header space needed in macvtap was not calculated
properly, fix it otherwise we splat past the beginning of the
packet. From Eric Dumazet.
21) Fix bcmgenet TCP TX perf regression, from Jaedon Shin.
22) Don't raw initialize or mod timers, use setup_timer() and
mod_timer() instead. From Vaishali Thakkar.
23) Fix software maintained statistics in bcmgenet and systemport
drivers, from Florian Fainelli.
24) DMA descriptor updates in sh_eth need proper memory barriers, from
Ben Hutchings.
25) Don't do UDP Fragmentation Offload on RAW sockets, from Michal
Kubecek.
26) Openvswitch's non-masked set actions aren't constructed properly
into netlink messages, fix from Joe Stringer.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (116 commits)
openvswitch: Fix serialization of non-masked set actions.
gianfar: Reduce logging noise seen due to phy polling if link is down
ibmveth: Add function to enable live MAC address changes
net: bridge: add compile-time assert for cb struct size
udp: only allow UFO for packets from SOCK_DGRAM sockets
sh_eth: Really fix padding of short frames on TX
Revert "sh_eth: Enable Rx descriptor word 0 shift for r8a7790"
sh_eth: Fix RX recovery on R-Car in case of RX ring underrun
sh_eth: Ensure proper ordering of descriptor active bit write/read
net/mlx4_en: Disbale GRO for incoming loopback/selftest packets
net/mlx4_core: Fix wrong mask and error flow for the update-qp command
net: systemport: fix software maintained statistics
net: bcmgenet: fix software maintained statistics
rxrpc: don't multiply with HZ twice
rxrpc: terminate retrans loop when sending of skb fails
net/hsr: Fix NULL pointer dereference and refcnt bugs when deleting a HSR interface.
net: pasemi: Use setup_timer and mod_timer
net: stmmac: Use setup_timer and mod_timer
net: 8390: axnet_cs: Use setup_timer and mod_timer
net: 8390: pcnet_cs: Use setup_timer and mod_timer
...
Currently the usbnet core does not update the tx_packets statistic for
drivers with FLAG_MULTI_PACKET and there is no hook in the TX
completion path where they could do this.
cdc_ncm and dependent drivers are bumping tx_packets stat on the
transmit path while asix and sr9800 aren't updating it at all.
Add a packet count in struct skb_data so these drivers can fill it
in, initialise it to 1 for other drivers, and add the packet count
to the tx_packets statistic on completion.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Tested-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Just another AX88178-based 10/100/1000 USB-to-Ethernet dongle. This one
shows up in lsusb as: "Sitecom Europe B.V. LN-028 Network USB 2.0 Adapter".
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Cc: Francois Romieu <romieu@fr.zoreil.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-usb@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Use helper functions to access current->state.
Direct assignments are prone to races and therefore buggy.
Thanks to Peter Zijlstra for the exact definition of the problem.
Suggested-By: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Always read bInterfaceNumber from the current altsetting, not from the first one
available in the altsetting array. This is coming from code review, not related
to any specific bug.
Signed-off-by: Aleksander Morgado <aleksander@aleksander.es>
Signed-off-by: David S. Miller <davem@davemloft.net>
The National Instruments USB Host-to-Host Cable is based on the Prolific
PL-25A1 chipset. Add its VID/PID so the plusb driver will recognize it.
Signed-off-by: Ben Shelton <ben.shelton@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support setting the rx coalesce. Then someone could change the rx
agg timeout value through ethtool.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rx early size is calculated with the mtu, so it has to be
re-calculated when the mtu is changed.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Separate USB_RX_EARLY_AGG into USB_RX_EARLY_TIMEOUT and USB_RX_EARLY_SIZE.
Replace r8153_set_rx_agg() with r8153_set_rx_early_timeout() and
r8153_set_rx_early_size().
Set the default timeout value according to the USB speed.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull kconfig updates from Michal Marek:
"Yann E Morin was supposed to take over kconfig maintainership, but
this hasn't happened. So I'm sending a few kconfig patches that I
collected:
- Fix for missing va_end in kconfig
- merge_config.sh displays used if given too few arguments
- s/boolean/bool/ in Kconfig files for consistency, with the plan to
only support bool in the future"
* 'kconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
kconfig: use va_end to match corresponding va_start
merge_config.sh: Display usage if given too few arguments
kconfig: use bool instead of boolean for type definition attributes
There is a capability which let the hw could change the settings
automatically when the power change to ON. However, the USB reset
would reset the settings to the hw default, so the driver has to
restore the relative settings. Otherwise, it would influence the
functions of the hw, and the compatibility for the USB hub and
USB host controller.
The relative settings are as following.
- set the power down scale to 96.
- enable the power saving function of USB 2.0.
- disable the ALDPS of ECM mode.
- set burst mode depending on the burst size.
- enable the flow control of endpoint full.
- set fifo empty boundary to 32448 bytes.
- enable the function of exiting LPM when Rx OK occurs.
- set the connect timer to 1.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If skb allocation fails once the IP header has been received, the rx state is
being set to WAIT_SYNC. The logic, though, shouldn't directly return, as the
buffer may contain a full packet, and therefore the WAIT_SYNC state needs to be
processed (resetting state to WAIT_IP, clearing rx_buf_size and re-initializing
rx_buf_missing).
So, just let the while loop continue so that in the next iteration the WAIT_SYNC
state cleanly stops the loop. The WAIT_SYNC processing will be done just after
that, only if the end of packet is flagged.
Signed-off-by: Aleksander Morgado <aleksander@aleksander.es>
Signed-off-by: David S. Miller <davem@davemloft.net>
vlan_get_protocol() has been defined and use it to replace
get_protocol().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Keep NETIF_F_HW_VLAN_CTAG_RX and NETIF_F_HW_VLAN_CTAG_TX at the
same line.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is unnecessary to accress the hw register if the device is unplugged.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace (tp->speed & LINK_STATUS) with netif_carrier_ok().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set LPM timer to 500us, except for RTL_VER_04 which doesn't link at
USB 3.0.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a error occurs when submitting rx, skip the remaining submissions
and try to submit them again next time.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass the static attribute groups and the driver data via
tty_port_register_device_attr() instead of manual device_create_file()
and device_remove_file() calls.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/vxlan.c
drivers/vhost/net.c
include/linux/if_vlan.h
net/core/dev.c
The net/core/dev.c conflict was the overlap of one commit marking an
existing function static whilst another was adding a new function.
In the include/linux/if_vlan.h case, the type used for a local
variable was changed in 'net', whereas the function got rewritten
to fix a stacked vlan bug in 'net-next'.
In drivers/vhost/net.c, Al Viro's iov_iter conversions in 'net-next'
overlapped with an endainness fix for VHOST 1.0 in 'net'.
In drivers/net/vxlan.c, vxlan_find_vni() added a 'flags' parameter
in 'net-next' whereas in 'net' there was a bug fix to pass in the
correct network namespace pointer in calls to this function.
Signed-off-by: David S. Miller <davem@davemloft.net>
The commone register macors (e.g. RSR) is too commont to drivers, it may
be conflict with the architectures (e.g. xtensa, sh).
The related warnings (with allmodconfig under xtensa):
CC [M] drivers/net/usb/sr9700.o
In file included from drivers/net/usb/sr9700.c:24:0:
drivers/net/usb/sr9700.h:65:0: warning: "RSR" redefined
#define RSR 0x06
^
In file included from ./arch/xtensa/include/asm/bitops.h:22:0,
from include/linux/bitops.h:36,
from include/linux/kernel.h:10,
from include/linux/list.h:8,
from include/linux/module.h:9,
from drivers/net/usb/sr9700.c:13:
./arch/xtensa/include/asm/processor.h:190:0: note: this is the location of the previous definition
#define RSR(v,sr) __asm__ __volatile__ ("rsr %0,"__stringify(sr) : "=a"(v));
^
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By using only the usb interface number for the rfkill name, we might
have a name conflicts in case two similar hso devices are connected.
In this patch, the name of the hso rfkill interface embed the value
of a counter that is incremented each time a new rfkill interface is
added.
Suggested-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
For hso serial devices, two cancel_work_sync were missing in the
disconnect method.
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
The serial_table is used to map the minor number of the usb serial device
to its associated context. The table is updated in the probe method and
in hso_serial_ref_free() which is called either from the tty cleanup
method or from the usb disconnect method.
This patch ensures that the serial_table is updated in the disconnect
method and no more from the cleanup method to avoid the following
potential race condition.
- hso_disconnect() is called for usb interface "x". Because the serial
port was open and because the cleanup method of the tty_port hasn't
been called yet, hso_serial_ref_free() is not run.
- hso_probe() is called and fails for a new hso serial usb interface
"y". The function hso_free_interface() is called and iterates
over the element of serial_table to find the device associated to
the usb interface context.
If the usb interface context of usb interface "y" has been created
at the same place as for usb interface "x", then the cleanup
functions are called for usb interfaces "x" and "y" and
hso_serial_ref_free() is called for both interfaces.
- release_tty() is called for serial port linked to usb interface "x"
and possibly crash because the tty_port structure contained in the
hso_device structure has been freed.
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function hso_serial_common_free() is called either by the cleanup
method of the tty or by the usb disconnect method.
In the former case, the usb_disconnect() has been already called
and the sysfs group associated to the device has been removed.
By calling tty_unregister directly from the usb_disconnect() method,
we avoid a warning due to the removal of the sysfs group of the usb
device.
Example of warning:
------------[ cut here ]------------
WARNING: CPU: 0 PID: 778 at fs/sysfs/group.c:225 sysfs_remove_group+0x50/0x94()
sysfs group c0645a88 not found for kobject 'ttyHS5'
Modules linked in:
CPU: 0 PID: 778 Comm: kworker/0:3 Tainted: G W 3.18.0+ #105
Workqueue: events release_one_tty
[<c000dfe4>] (unwind_backtrace) from [<c000c014>] (show_stack+0x14/0x1c)
[<c000c014>] (show_stack) from [<c0016bac>] (warn_slowpath_common+0x5c/0x7c)
[<c0016bac>] (warn_slowpath_common) from [<c0016c60>] (warn_slowpath_fmt+0x30/0x40)
[<c0016c60>] (warn_slowpath_fmt) from [<c00ddd14>] (sysfs_remove_group+0x50/0x94)
[<c00ddd14>] (sysfs_remove_group) from [<c0221e44>] (device_del+0x30/0x190)
[<c0221e44>] (device_del) from [<c0221fb0>] (device_unregister+0xc/0x18)
[<c0221fb0>] (device_unregister) from [<c0221fec>] (device_destroy+0x30/0x3c)
[<c0221fec>] (device_destroy) from [<c01fe1dc>] (tty_unregister_device+0x2c/0x5c)
[<c01fe1dc>] (tty_unregister_device) from [<c029a428>] (hso_serial_common_free+0x2c/0x88)
[<c029a428>] (hso_serial_common_free) from [<c029a4c0>] (hso_serial_ref_free+0x3c/0xb8)
[<c029a4c0>] (hso_serial_ref_free) from [<c01ff430>] (release_one_tty+0x30/0x84)
[<c01ff430>] (release_one_tty) from [<c00271d4>] (process_one_work+0x21c/0x3c8)
[<c00271d4>] (process_one_work) from [<c0027758>] (worker_thread+0x3d8/0x560)
[<c0027758>] (worker_thread) from [<c002be4c>] (kthread+0xc0/0xcc)
[<c002be4c>] (kthread) from [<c0009630>] (ret_from_fork+0x14/0x24)
---[ end trace cb88537fdc8fa208 ]---
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need for a dedicated reset work in the hso driver since
there is already a reset work foreseen in usb_interface that does
the same.
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
In other functions of the driver, variables of type "struct hso_serial"
are denoted by "serial" and variables of type "struct hso_device" are
denoted by "hso_dev". This patch makes the hso_free_interface()
consistent with these notations.
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the rfkill interface was created, a buffer containing the name
of the rfkill node was allocated. This buffer was never freed when the
device disappears.
To fix the problem, we put the name given to rfkill_alloc() in
the hso_net structure.
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the disconnect path, tx_buffer should freed like tx_data to avoid
a memory leak when the device disconnects.
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the device disappear, the function hso_disconnect() is called to
perform cleanup. In the cleanup function, hso_free_interface() calls
tty_port_tty_hangup() in view of scheduling a work to hang up the tty if
needed. If the port was not open then hso_serial_ref_free() is called
directly to cleanup everything. Otherwise, hso_serial_ref_free() is called
when the last fd associated to the port is closed.
For each open port, tty_release() will call the close method,
hso_serial_close(), which drops the last kref and call
hso_serial_ref_free() which unregisters, destroys the tty port
and finally frees the structure in which the tty_port structure
is included. Later, in tty_release(), more precisely when release_tty()
is called, the tty_port previously freed is accessed to cancel
the tty buf workqueue and it leads to a crash.
In view of avoiding this crash, we add a cleanup method that is called
at the end of the hangup process and we drop the last kref in this
function when all the ports have been closed, when tty_port is no
more needed and when it is safe to free the structure containing the
tty_port structure.
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
No timer related function is used in this driver.
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
arch/arm/boot/dts/imx6sx-sdb.dts
net/sched/cls_bpf.c
Two simple sets of overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Call hex2bin() library function, instead of doing conversion here.
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Read OCP register 0xa43a~0xa43b would clear some flags which the hw
would use, and it may let the device lost. However, the unit of
reading is 4 bytes. That is, it would read 0xa438~0xa43b when calling
sram_read() to read OCP_SRAM_DATA.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For ocp_write_word() and ocp_write_byte(), there is a generic_ocp_read()
which is used to read the whole 4 byte data, keep the unchanged bytes,
and modify the expected bytes. However, the "byen" could be used to
determine which bytes of the 4 bytes to write, so the action could be
removed.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/xen-netfront.c
Minor overlapping changes in xen-netfront.c, mostly to do
with some buffer management changes alongside the split
of stats into TX and RX.
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace tasklet with NAPI.
Add rx_queue to queue the remaining rx packets if the number of the
rx packets is more than the request from poll().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The same macros are used for rx as well. So rename it.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit e4c7f259c5 ("USB: kaweth.c: use GFP_ATOMIC under spin_lock")
makes sure that kaweth_internal_control_msg() allocates memory with GFP_ATOMIC,
but kaweth_internal_control_msg() also calls usb_start_wait_urb()
that still allocates memory with GFP_NOIO.
The patch fixes usb_start_wait_urb() as well.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't submit the rx if the device is unplugged, stopped, or
linking down.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove rtl_start_rx() from rtl_enable() and put it after calling
netif_carrier_on().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support for keyword 'boolean' will be dropped later on.
No functional change.
Reference: http://lkml.kernel.org/r/cover.1418003065.git.cj@linux.com
Signed-off-by: Christoph Jaeger <cj@linux.com>
Signed-off-by: Michal Marek <mmarek@suse.cz>
Support ndo_features_check to avoid:
- the transport offset is more than the hw limitation when using hw checksum.
- the skb->len of a GSO packet is more than the limitation.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some buggy firmwares export an incorrect MAC address (00:a0:c6:00:00:00). This
makes for example checking devices for random MAC addresses tricky, and you
might end up with multiple network interfaces with the same address.
This patch tries to fix, or at least improve, the situation by setting the MAC
address of devices with this firmware bug to a random address. I tested the
patch with two devices that has this firmware bug (Huawei E398 and E392), and
network traffic worked fine after changing the address.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Redefine REALTEK_USB_DEVICE for the desired USB interface for probe().
There are three USB interfaces for the device. USB_CLASS_COMM and
USB_CLASS_CDC_DATA are for ECM mode (config #2). USB_CLASS_VENDOR_SPEC
is for the vendor mode (config #1). However, we are not interesting
in USB_CLASS_CDC_DATA for probe(), so redefine REALTEK_USB_DEVICE
to ignore the USB interface class of USB_CLASS_CDC_DATA.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ieee802154/fakehard.c
A bug fix went into 'net' for ieee802154/fakehard.c, which is removed
in 'net-next'.
Add build fix into the merge from Stephen Rothwell in openvswitch, the
logging macros take a new initial 'log' argument, a new call was added
in 'net' so when we merge that in here we have to explicitly add the
new 'log' arg to it else the build fails.
Signed-off-by: David S. Miller <davem@davemloft.net>
The kfree() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
If there is a error for r8152_submit_rx(), add the remaining rx
buffers to the list. Then the remaining rx buffers could be
submitted later.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The behavior of handling the returned status from r8152_submit_rx()
is almost same, so let r8152_submit_rx() deal with the error
directly. This could avoid the duplicate code.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since both tx and rx paths work with skb->vlan_tci, there's no need for
this function anymore. Switch users directly to __vlan_hwaccel_put_tag.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added the USB VID/PID for the HP lt4112 LTE/HSPA+ Gobi 4G Modem (Huawei me906e)
Signed-off-by: Martin Hauke <mardnh@gmx.de>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/chelsio/cxgb4vf/sge.c
drivers/net/ethernet/intel/ixgbe/ixgbe_phy.c
sge.c was overlapping two changes, one to use the new
__dev_alloc_page() in net-next, and one to use s->fl_pg_order in net.
ixgbe_phy.c was a set of overlapping whitespace changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
If the device is unplugged or !netif_running(), the workqueue
doesn't need to wake the device, and could return directly.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clear the flag of SCHEDULE_TASKLET in bottom_half() to avoid
re-schedule the tasklet again by workqueue.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The INIT_LIST_HEAD(&tp->rx_done) would be done in rtl_start_rx(),
so remove the unnecessary one in alloc_all_mem().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the calls to __skb_alloc_page that are passed NULL with calls to
__dev_alloc_page.
In addition remove __GFP_COLD flag from allocations as we only want it for
the Rx buffer which is taken care of by __dev_alloc_skb, not for any
secondary allocations such as the queue element transmit descriptors.
Cc: Oliver Neukum <oliver@neukum.org>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
we were dereferencing dev to initialize pdata. but just after that we
have a BUG_ON(!dev). so we were basically dereferencing the pointer
first and then tesing it for NULL.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 3cc81d85ee ("asix: Don't reset PHY on if_up for ASIX 88772")
causes the ethernet on Arndale to no longer function. This appears to
be because the Arndale ethernet requires a full reset before it will
function correctly, however simply reverting the above patch causes
problems with ethtool settings getting reset.
It seems the problem is that the ethernet is not properly reset during
bind, and indeed the code in ax88772_bind that resets the device is a
very small subset of the actual ax88772_reset function. This patch uses
ax88772_reset in place of the existing reset code in ax88772_bind which
removes some code duplication and fixes the ethernet on Arndale.
It is still possible that the original patch causes some issues with
suspend and resume but that seems like a separate issue and I haven't
had a chance to test that yet.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Tested-by: Riku Voipio <riku.voipio@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Olivier having laid the groundwork this patch transmits the
multicast flag to the device to save some bus traffic.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PIDs are only used in the id table, so the definitions are
unnacessary. Remove them wouldn't have confusion.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace using VID/PID with using tp->version to initialize the ops.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move r8152b_get_version() to the location before rtl_ops_init().
Then, the rtl_ops_init() could use tp->version.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let the tasklet only be enabled after open(), and be disabled for
the other situation. The tasklet is only necessary after open() for
tx/rx, so it could be disabled by default.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For Renesas USB 3.0 host controller, when unplugging the usb hub which
has the RTL8153 plugged, the driver would get -EPROTO for interrupt
transfer. There is high probability to get the information of "HC died;
cleaning up", if the driver continues to submit the interrupt transfer
before the disconnect() is called.
[ 1024.197678] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.213673] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.229668] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.245661] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.261653] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.277648] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.293642] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.309638] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.325633] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.341627] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.357621] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.373615] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.383097] usb 9-1: USB disconnect, device number 2
[ 1024.383103] usb 9-1.4: USB disconnect, device number 6
[ 1029.391010] xhci_hcd 0000:04:00.0: xHCI host not responding to stop endpoint command.
[ 1029.391016] xhci_hcd 0000:04:00.0: Assuming host is dying, halting host.
[ 1029.392551] xhci_hcd 0000:04:00.0: HC died; cleaning up
[ 1029.421480] usb 8-1: USB disconnect, device number 2
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set RTL8152_UNPLUG when finding -ENODEV. This could accelerate
unloading the driver when the device is unplugged.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid unnecessary behavior when autosuspend occurs during open().
The relative processes should only be run after finishing open().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If (tp->speed & LINK_STATUS) is not zero, the rtl8152_resume()
would call rtl_start_rx() before enabling the tx/rx. Avoid this
by resetting it to zero.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The flag of SELECTIVE_SUSPEND should be cleared when autoresuming.
Otherwise, when the system suspend and resume occur, it may have
the wrong flow.
Besides, because the flag of SELECTIVE_SUSPEND couldn't be used
to check if the hw enables the relative feature, it should alwayes
be disabled in close().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace tx_underun with tx_underrun for checkpatch.pl.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Promiscuous mode was not supported anymore with my Lenovo adapters
(RTL8153) since commit c472ab68ad
(cdc-ether: clean packet filter upon probe).
It was not possible to use them in a bridge anymore.
Signed-off-by: Olivier Blin <olivier.blin@softathome.com>
Also-analyzed-by: Loïc Yhuel <loic.yhuel@softathome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will be used by the set_rx_mode callback.
Also move a comment about multicast filtering in this new function.
Signed-off-by: Olivier Blin <olivier.blin@softathome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To delegate promiscuous mode and multicast filtering to the subdriver.
Signed-off-by: Olivier Blin <olivier.blin@softathome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following patch fixes a bug which causes the ax88179_178a driver to be
incapable of being added to a bond.
When I brought up the issue with the bonding maintainers, they indicated
that the real problem was with the NIC driver which must return zero for
success (of setting the MAC address). I see that several other NIC drivers
follow that pattern by either simply always returing zero, or by passing
through a negative (error) result while rewriting any positive return code
to zero. With that same philisophy applied to the ax88179_178a driver, it
allows it to work correctly with the bonding driver.
I believe this is suitable for queuing in -stable, as it's a small, simple,
and obvious fix that corrects a defect with no other known workaround.
This patch is against vanilla 3.17(.0).
Signed-off-by: Ian Morgan <imorgan@primordial.ca>
drivers/net/usb/ax88179_178a.c | 7 ++++++-
1 file changed, 6 insertions(+), 1 deletion(-)
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove calling cancel_delayed_work_sync() for runtime suspend,
because it would cause dead lock. Instead, return -EBUSY to
avoid the device enters suspending if the net is running and
the delayed work is pending or running. The delayed work would
try to wake up the device later, so the suspending is not
necessary.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the mutex to avoid the settings are interrupted by other ones.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add usb_autopm_xxx for rtl8152_get_settings() ,and remove
usb_autopm_xxx from read_mii_word() and write_mii_word().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
"Most notable changes in here:
1) By far the biggest accomplishment, thanks to a large range of
contributors, is the addition of multi-send for transmit. This is
the result of discussions back in Chicago, and the hard work of
several individuals.
Now, when the ->ndo_start_xmit() method of a driver sees
skb->xmit_more as true, it can choose to defer the doorbell
telling the driver to start processing the new TX queue entires.
skb->xmit_more means that the generic networking is guaranteed to
call the driver immediately with another SKB to send.
There is logic added to the qdisc layer to dequeue multiple
packets at a time, and the handling mis-predicted offloads in
software is now done with no locks held.
Finally, pktgen is extended to have a "burst" parameter that can
be used to test a multi-send implementation.
Several drivers have xmit_more support: i40e, igb, ixgbe, mlx4,
virtio_net
Adding support is almost trivial, so export more drivers to
support this optimization soon.
I want to thank, in no particular or implied order, Jesper
Dangaard Brouer, Eric Dumazet, Alexander Duyck, Tom Herbert, Jamal
Hadi Salim, John Fastabend, Florian Westphal, Daniel Borkmann,
David Tat, Hannes Frederic Sowa, and Rusty Russell.
2) PTP and timestamping support in bnx2x, from Michal Kalderon.
3) Allow adjusting the rx_copybreak threshold for a driver via
ethtool, and add rx_copybreak support to enic driver. From
Govindarajulu Varadarajan.
4) Significant enhancements to the generic PHY layer and the bcm7xxx
driver in particular (EEE support, auto power down, etc.) from
Florian Fainelli.
5) Allow raw buffers to be used for flow dissection, allowing drivers
to determine the optimal "linear pull" size for devices that DMA
into pools of pages. The objective is to get exactly the
necessary amount of headers into the linear SKB area pre-pulled,
but no more. The new interface drivers use is eth_get_headlen().
From WANG Cong, with driver conversions (several had their own
by-hand duplicated implementations) by Alexander Duyck and Eric
Dumazet.
6) Support checksumming more smoothly and efficiently for
encapsulations, and add "foo over UDP" facility. From Tom
Herbert.
7) Add Broadcom SF2 switch driver to DSA layer, from Florian
Fainelli.
8) eBPF now can load programs via a system call and has an extensive
testsuite. Alexei Starovoitov and Daniel Borkmann.
9) Major overhaul of the packet scheduler to use RCU in several major
areas such as the classifiers and rate estimators. From John
Fastabend.
10) Add driver for Intel FM10000 Ethernet Switch, from Alexander
Duyck.
11) Rearrange TCP_SKB_CB() to reduce cache line misses, from Eric
Dumazet.
12) Add Datacenter TCP congestion control algorithm support, From
Florian Westphal.
13) Reorganize sk_buff so that __copy_skb_header() is significantly
faster. From Eric Dumazet"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1558 commits)
netlabel: directly return netlbl_unlabel_genl_init()
net: add netdev_txq_bql_{enqueue, complete}_prefetchw() helpers
net: description of dma_cookie cause make xmldocs warning
cxgb4: clean up a type issue
cxgb4: potential shift wrapping bug
i40e: skb->xmit_more support
net: fs_enet: Add NAPI TX
net: fs_enet: Remove non NAPI RX
r8169:add support for RTL8168EP
net_sched: copy exts->type in tcf_exts_change()
wimax: convert printk to pr_foo()
af_unix: remove 0 assignment on static
ipv6: Do not warn for informational ICMP messages, regardless of type.
Update Intel Ethernet Driver maintainers list
bridge: Save frag_max_size between PRE_ROUTING and POST_ROUTING
tipc: fix bug in multicast congestion handling
net: better IFF_XMIT_DST_RELEASE support
net/mlx4_en: remove NETDEV_TX_BUSY
3c59x: fix bad split of cpu_to_le32(pci_map_single())
net: bcmgenet: fix Tx ring priority programming
...
Here's the big USB patchset for 3.18-rc1. Also in here is the PHY tree,
as it seems to fit well with the USB tree for various reasons...
Anyway, lots of little changes in here, all over the place, full details
in the changelog below.
All have been in the linux-next tree for a while with no issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlQ0aLYACgkQMUfUDdst+ylBvwCgs9fGRj0RQkLyGhQdEpzdZtTU
ZcwAoMPBImnaA1ZeSl7ZnoO8vC/WE4bR
=tfpj
-----END PGP SIGNATURE-----
Merge tag 'usb-3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB updates from Greg KH:
"Here's the big USB patchset for 3.18-rc1. Also in here is the PHY
tree, as it seems to fit well with the USB tree for various reasons...
Anyway, lots of little changes in here, all over the place, full
details in the changelog
All have been in the linux-next tree for a while with no issues"
* tag 'usb-3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (244 commits)
USB: host: st: fix typo 'CONFIG_USB_EHCI_HCD_ST'
uas: Reduce number of function arguments for uas_alloc_foo functions
xhci: Allow xHCI drivers to be built as separate modules
xhci: Export symbols used by host-controller drivers
xhci: Check for XHCI_COMP_MODE_QUIRK when disabling D3cold
xhci: Introduce xhci_init_driver()
usb: hcd: add generic PHY support
usb: rename phy to usb_phy in HCD
usb: gadget: uvc: fix up uvcg_v4l2_get_unmapped_area typo
USB: host: st: fix ehci/ohci driver selection
usb: host: ehci-exynos: Remove unnecessary usb-phy support
usb: core: return -ENOTSUPP for all targeted hosts
USB: Remove .owner field for driver
usb: core: log higher level message on malformed LANGID descriptor
usb: Add LED triggers for USB activity
usb: Rename usb-common.c
usb: gadget: Refactor request completion
usb: gadget: Introduce usb_gadget_giveback_request()
usb: dwc2/gadget: move phy bus legth initialization
phy: remove .owner field for drivers using module_platform_driver
...
Restart autonegotiation is necessary after setting EEE.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Resume the device before setting the MAC address.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I've noticed every time the interface is set to 'up,', the kernel
reports that the link speed is set to 100 Mbps/Full Duplex, even
when ethtool is used to set autonegotiation to 'off', half
duplex, 10 Mbps.
It can be tested by:
ifconfig eth0 down
ethtool -s eth0 autoneg off speed 10 duplex half
ifconfig eth0 up
Then checking 'dmesg' for the link speed.
Signed-off-by: Michel Stam <m.stam@fugro.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/usb/r8152.c
net/netfilter/nfnetlink.c
Both r8152 and nfnetlink conflicts were simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
The firmware would be clear when the power cut is enabled for
RTL8153.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The xxx_clear_bp() is used to halt the firmware. It only necessary
for updating the new firmware. Besides, depend on the version of
the current firmware, it may have problem to halt the firmware
directly. Finally, halt the firmware would let the firmware code
useless, and the bugs which are fixed by the firmware would occur.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The flag of RTL8152_UNPLUG should only be set when the device is
unplugged, not each time the rtl8152_disconnect() is called.
Otherwise, the device wouldn't be stopped normally.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add functions to enable EEE and set EEE advertisement.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the EEE definitions with the ones which is declared
in "mdio.h".
Chage some definitions to make them readable.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netif_carrier_off would be called when autoresuming, even though
the cable is plugged. This causes some applications do relative
actions when detecting the carrier off. Keep the status of the
carrier, and let it be modified when the linking change occurs.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
includes miscellaneous cleanup of other PHY drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Efl5
-----END PGP SIGNATURE-----
Merge tag 'phy-for_3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next
Kishon writes:
Adds 3 new PHY drivers stih407, stih41x and rcar gen2 PHY. It also
includes miscellaneous cleanup of other PHY drivers.
Conflicts:
MAINTAINERS
USB hub has started to use a workqueue instead of kthread. Let's update
the documentation and comments here and there.
This patch mostly just replaces "khubd" with "hub_wq". There are only few
exceptions where the whole sentence was updated. These more complicated
changes can be found in the following files:
Documentation/usb/hotplug.txt
drivers/net/usb/usbnet.c
drivers/usb/core/hcd.c
drivers/usb/host/ohci-hcd.c
drivers/usb/host/xhci.c
Signed-off-by: Petr Mladek <pmladek@suse.cz>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Conflicts:
arch/mips/net/bpf_jit.c
drivers/net/can/flexcan.c
Both the flexcan and MIPS bpf_jit conflicts were cases of simple
overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
If the hw is in ALDPS mode, the hw may have no response for accessing
the most registers. Therefore, the ALDPS should be disabled before
accessing the hw in rtl_ops.init(), rtl_ops.disable(), rtl_ops.up(),
and rtl_ops.down(). Regardless of rtl_ops.enable(), because the hw
wouldn't enter ALDPS mode when linking on. The hw would enter the
ALDPS mode after several seconds when link down occurs and the ALDPS
is enabled.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support hw VLAN for tx and rx. And enable them by default.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace mdelay with usleep_range to avoid busy loop.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the hw doesn't have a valid MAC address, give a random one and
set it to the hw.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Exchange the location of rtl8152_set_mac_address() and
set_ethernet_addr(). Then, the set_ethernet_addr() could
set the MAC address by calling rtl8152_set_mac_address()
later.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The variable "rx_buf_sz" is used by both tx and rx buffers. Replace
it with "agg_buf_sz".
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because the Tx has the features of stopping queue and aggregation,
We don't need many tx buffers. Change the tx number from 10 to 4
to reduce the usage of the memory. This could save 16K * 6 bytes
memory.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the strncpy with strlcpy, and use sizeof to determine the
length.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
626: CHECK: Alignment should match open parenthesis
646: CHECK: Alignment should match open parenthesis
655: CHECK: Alignment should match open parenthesis
695: CHECK: Alignment should match open parenthesis
729: CHECK: Alignment should match open parenthesis
739: CHECK: Alignment should match open parenthesis
976: WARNING: externs should be avoided in .c files
1314: CHECK: Alignment should match open parenthesis
1358: WARNING: networking block comments don't use an empty /* line, use /* Comment...
1402: WARNING: networking block comments don't use an empty /* line, use /* Comment...
1521: CHECK: multiple assignments should be avoided
1775: CHECK: Alignment should match open parenthesis
1838: CHECK: multiple assignments should be avoided
1843: CHECK: multiple assignments should be avoided
1847: CHECK: multiple assignments should be avoided
1850: WARNING: Missing a blank line after declarations
1864: CHECK: Alignment should match open parenthesis
1872: CHECK: braces {} should be used on all arms of this statement
1906: CHECK: usleep_range is preferred over udelay
2865: WARNING: networking block comments don't use an empty /* line, use /* Comment...
3088: CHECK: Alignment should match open parenthesis
total: 0 errors, 5 warnings, 16 checks, 3567 lines checked
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It must be tristate to avoid broken dependencies with kernel built-in
usb network drivers when usb support is module only.
When net config option is set, least surprize default should match usb.
Wireless RNDIS USB driver used to select USB_USBNET. USB_USBNET now
depends on USB_NET_DRIVERS so the latter should be selected as well.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/Makefile
net/ipv6/sysctl_net_ipv6.c
Two ipv6_table_template[] additions overlap, so the index
of the ipv6_table[x] assignments needed to be adjusted.
In the drivers/net/Makefile case, we've gotten rid of the
garbage whereby we had to list every single USB networking
driver in the top-level Makefile, there is just one
"USB_NETWORKING" that guards everything.
Signed-off-by: David S. Miller <davem@davemloft.net>
USB network drivers are already handled in drivers/net/usb/Kconfig.
Let's save the maintenance burden of dependencies in drivers/net/Makefile.
The newly introduced USB_NET_DRIVERS umbrella config option defaults
to 'y' so as to minimize the changes of behavior.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This device needs to be reset to recover from a timeout.
Unfortunately this can be handled only at the level of
the subdrivers.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add functions to support ethtool EEE manipulating, and the EEE
is disabled in default setting to enhance the compatibility
with certain switch.
Signed-off-by: Freddy Xin <freddy@asix.com.tw>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 20fbe3ae99.
As reported by Stephen Rothwell, it causes compile failures in certain
configurations:
drivers/net/usb/cdc_subset.c:360:15: error: 'dummy_prereset' undeclared here (not in a function)
.pre_reset = dummy_prereset,
^
drivers/net/usb/cdc_subset.c:361:16: error: 'dummy_postreset' undeclared here (not in a function)
.post_reset = dummy_postreset,
^
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: David Miller <davem@davemloft.net>
Cc: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are devices that don't do reset all the way. So the packet filter should
be set to a sane initial value. Failure to do so leads to intermittent failures
of DHCP on some systems under some conditions.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This device needs to be reset to recover from a timeout.
Unfortunately this can be handled only at the level of
the subdrivers.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the usb speed of the RTL8152 is not high speed, the USB_DEV_STAT[2:1]
should be equal to [0 1]. That is, the STAT_SPEED_FULL should be equal
to 2.
There is a easy way to check the usb speed by the speed field of the
struct usb_device. Use it to replace the original metheod.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Spotted-by: Andrey Utkin <andrey.krieger.utkin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/infiniband/hw/cxgb4/device.c
The cxgb4 conflict was simply overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Huawei's usage of the subclass and protocol fields is not 100%
clear to us, but there appears to be a very strict system.
A device with the "shared" device ID 12d1:1506 and this NCM
function was recently reported (showing only default altsetting):
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 1
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 3
bInterfaceProtocol 22
iInterface 8 CDC Network Control Model (NCM)
** UNRECOGNIZED: 05 24 00 10 01
** UNRECOGNIZED: 06 24 1a 00 01 1f
** UNRECOGNIZED: 0c 24 1b 00 01 00 04 10 14 dc 05 20
** UNRECOGNIZED: 0d 24 0f 0a 0f 00 00 00 ea 05 03 00 01
** UNRECOGNIZED: 05 24 06 01 01
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x85 EP 5 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0010 1x 16 bytes
bInterval 9
Cc: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add two device IDs found in an out-of-tree driver downloadable
from Netgear.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the module sends bursts of data, sometimes a deadlock happens in
the hso driver when the tty buffer doesn't get the chance to be flushed
quickly enough.
Remove the endless while loop in function put_rxbuf_data() which is
called by the urb completion handler.
If there isn't enough room in the tty buffer, discards all the data
received in the URB.
Cc: David Miller <davem@davemloft.net>
Cc: David Laight <David.Laight@ACULAB.COM>
Cc: One Thousand Gnomes <gnomes@lxorguk.ukuu.org.uk>
Cc: Dan Williams <dcbw@redhat.com>
Cc: Jan Dumon <j.dumon@option.com>
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The workqueue "retry_unthrottle_workqueue" is not scheduled anywhere
in the code. So, remove it.
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
The transport offset of the IPv4 packet should be fixed and wouldn't
be out of the hw limitation, so the r8152_csum_workaround() should
be used for IPv6 packets.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The smsc95xx needs to resume with reset operation. Otherwise it causes
system hang by network error like below after resume. This case appears
on odroid u3 board.
[ 9.727600] smsc95xx 1-2:1.0 eth0: kevent 2 may have been dropped
[ 9.727648] smsc95xx 1-2:1.0 eth0: kevent 2 may have been dropped
[ 9.727689] smsc95xx 1-2:1.0 eth0: kevent 2 may have been dropped
[ 9.727728] smsc95xx 1-2:1.0 eth0: kevent 2 may have been dropped
[ 9.729486] PM: resume of devices complete after 2011.219 msecs
[ 10.117609] Restarting tasks ... done.
[ 11.725099] smsc95xx 1-2:1.0 eth0: kevent 2 may have been dropped
[ 13.480846] smsc95xx 1-2:1.0 eth0: kevent 2 may have been dropped
[ 13.481361] smsc95xx 1-2:1.0 eth0: kevent 2 may have been dropped
...
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The maximum jumbo frame size for RTL8153 is 9K bytes.
Change the max rx packet size to 9K.
Change the use of the shared fifo from 6K (default) to 12K for tx.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device should be waked up from runtime suspend before dumping
the hw counter.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the system is too busy to complete the urb, the tx timout function
would be called. This causes the other tx urbs would be killed, too.
Increase the tx timeout to avoid it.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's a new version of the Telewell 4G modem working with, but not
recognized by this driver.
Signed-off-by: Bernd Wachter <bernd.wachter@jolla.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Messages from the modem exceeding 256 bytes cause communication
failure.
The WDM protocol is strictly "read on demand", meaning that we only
poll for unread data after receiving a notification from the modem.
Since we have no way to know how much data the modem has to send,
we must make sure that the buffer we provide is "big enough".
Message truncation does not work. Truncated messages are left unread
until the modem has another message to send. Which often won't
happen until the userspace application has given up waiting for the
final part of the last message, and therefore sends another command.
With a proper CDC WDM function there is a descriptor telling us
which buffer size the modem uses. But with this vendor specific
implementation there is no known way to calculate the exact "big
enough" number. It is an unknown property of the modem firmware.
Experience has shown that 256 is too small. The discussion of
this failure ended up concluding that 512 might be too small as
well. So 1024 seems like a reasonable value for now.
Fixes: 41c47d8cfd ("net: huawei_cdc_ncm: Introduce the huawei_cdc_ncm driver")
Cc: Enrico Mioso <mrkiko.rs@gmail.com>
Reported-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-By: Enrico Mioso <mrkiko.rs@gmail.com>
Tested-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/core/rtnetlink.c
net/core/skbuff.c
Both conflicts were very simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Lars writes: "I'm only 99% sure that the net interfaces are qmi
interfaces, nothing to lose by adding them in my opinion."
And I tend to agree based on the similarity with the two Olicard
modems we already have here.
Reported-by: Lars Melin <larsm17@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
include/net/inetpeer.h
net/ipv6/output_core.c
Changes in net were fixing bugs in code removed in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
Each iPad model has a different product id, this patch adds support for iPad 2
(pid 0x12a2) and iPad 3 (pid 0x12a6). Note that iPad 2 must be jailbroken and a
third-party app must be used for tethering to work. On iPad 3, tethering works
out of the box (assuming your ISP is nice).
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The min_tx_pkt variable decides the cutoff point where the driver
will stop padding out NTBs to maximum size. The padding is a tradeoff
where we use some USB bus bandwidth to allow the device to receive
fixed size buffers. Different devices will have different optimal
settings, spanning from no padding at all to padding every NTB.
There is no way to automatically figure out which setting is best
for a specific device.
The default value is a reasonable tradeoff, calculated based on the
USB packet size and out NTB max size. This may have to be changed
along with any tx_max changes.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mandatory GetNtbParameters control request is an important part of
the host <-> device protocol negotiation in CDC NCM (and CDC MBIM). It
gives device limits which the host must obey when configuring the
protocol aggregation variables. The driver will enforce this by
rejecting attempts to set any of the tunable variables to a value
which is not supported by the device. Exporting the parameter block
helps userspace decide which values are allowed without resorting
to trial and error.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool coalesce API is not applicable for this driver. Forcing
it to fit the NCM aggregation redefined the API in a driver specific
way, which is much worse than defining a clean new API. These ethtool
coalesce functions have therefore been replaced by a new sysfs API.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Attach a driver specific sysfs group to the netdev, and use it
for the rx/tx aggregation variables.
The datagram aggregation defined by the CDC NCM specification is
specific to this device class (including CDC MBIM). Using the
ethtool interrupt coalesce API as an interface to the aggregation
parameters redefined that API in a driver specific and confusing
way. A sysfs group
- makes it clear that this is a driver specific userspace API, and
- allows us to export the real values instead of some translated
version, and
- lets us include more aggregation variables which were impossible
to force into the ethtool API.
Additionally, using sysfs allows tuning the driver on space
constrained hosts where userspace tools like ethtool are undesired.
Suggested-by: Peter Stuge <peter@stuge.se>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
It doesn't matter whether the buffer size goes up or down. We have to
keep usbnet and device syncronized to be able to split transfers at the
correct boundaries. The spec allow skipping short packets when using
max sized transfers. If we don't tell usbnet about our new expected rx
buffer size, then it will merge and/or split NTBs. The driver does not
support this, and the result will be lots of framing errors.
Fix by always reallocating usbnet rx buffers when the rx_max value
changes.
Fixes: 68864abf08 ("net: cdc_ncm: support rx_max/tx_max updates when running")
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are calling usbnet_start_xmit() to flush any remaining data,
depending on the side effect that tx_curr_skb is set to NULL,
ensuring a new allocation using the updated tx_max. But this
side effect will only happen if there were any cached data ready
to transmit. If not, then an empty tx_curr_skb is still allocated
using the old tx_max size. Free it to avoid a buffer overrun.
Fixes: 68864abf08 ("net: cdc_ncm: support rx_max/tx_max updates when running")
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cloning the big skbs we use for USB buffering chokes up TCP and
SCTP because the socket memory limits are hitting earlier than
they should. It is better to unconditionally copy the unwrapped
packets to freshly allocated skbs.
Reported-by: Jim Baxter <jim_baxter@mentor.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
This interface is unusable, as the cdc-wdm character device doesn't reply to
any QMI command. Also, the out-of-tree Sierra Wireless GobiNet driver fully
skips it.
Signed-off-by: Aleksander Morgado <aleksander@aleksander.es>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
A set of new VID/PIDs retrieved from the out-of-tree GobiNet/GobiSerial
Sierra Wireless drivers.
Signed-off-by: Aleksander Morgado <aleksander@aleksander.es>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
This issue was reported by coccicheck using the semantic patch
at scripts/coccinelle/api/memdup.cocci
Signed-off-by: Benoit Taine <benoit.taine@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a typo here where we test for USB_CDC_NCM_NTH32_SIGN instead
of USB_CDC_NCM_NTB32_SUPPORTED. The test probably still works as
written because 0x686D636E has (1 << 1) set and doesn't have (1 << 0)
set.
Fixes: f8afb73da3 ('net: cdc_ncm: factor out one-time device initialization')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The upper timer_interval limit is arbitrary and much higher
than anything usable in the real world. Reducing it from 15s
to ~4s to make the timer_interval fit in an u32 does not make
much difference. The limit is still outside the practical
bounds.
This eliminates the need for a 64bit timer_interval, fixing a
build error related to 64bit division:
drivers/built-in.o: In function `cdc_ncm_get_coalesce':
ak8975.c:(.text+0x1ac994): undefined reference to `__aeabi_uldivmod'
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can end up with a freshly allocated tx_curr_skb with no frames
in it. In this case it does not make any sense to start the timer.
This avoids the timer periodically trying to start tx when there
is nothing in the queue.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calling netif_carrier_{on,off} is sufficient. There is no need
to duplicate the carrier state in a driver specific flag.
Acked-by: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lots of devices request much larger buffers than reasonable. This
cause real problems for users of hosts with limited resources.
Reducing the default buffer size to 16kB for such devices is
a reasonable trade-off between allowing them to aggregate traffic
and avoiding memory exhaustion on resource restrained hosts.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
To have an idea of the effects of the protocol coalescing
it's useful to have some counters showing the different
aspects.
Due to the asymmetrical usbnet interface the netdev
rx_bytes counter has been counting real received payload,
while the tx_bytes counter has included the NCM/MBIM
framing overhead. This overhead can be many times the
payload because of the aggressive padding strategy of
this driver, and will vary a lot depending on device
and traffic.
With very few exceptions, users are only interested in
the payload size. Having an somewhat accurate payload
byte counter is particularly important for mobile
broadband devices, which many NCM devices and of course
all MBIM devices are. Users and userspace applications
will use this counter to monitor account quotas.
Having protocol specific counters for the overhead, we are
now able to correct the tx_bytes netdev counter so that
it shows the real payload
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
We pad frames larger than X to maximum size for devices which
don't need a ZLP after maximum sized frames. This allows the
device to optimize its transfers for one fixed buffer size.
X was arbitrarily set at 512 bytes regardless of real buffer
maximum, causing extreme overheads due to excessive padding of
larger tx buffers. Limit the padding to at most 3 full USB
packets, still allowing the overhead to payload ratio of 3/1.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many newer NCM and MBIM devices will request a maximum tx
datagram count which is much smaller than our hard-coded
absolute max. We can reduce the overhead without sacrificing
any of the simplicity for these devices, by simply using the
true negotiated count in when calculated the maximum NTH and
NDP header sizes.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Datagram coalescing is an integral part of the NCM and MBIM
protocols, intended to reduce the interrupt load primarily
on the device end of the USB link. As with all coalescing
solutions, there is a trade-off between buffering and
interrupts.
The current defaults are based on the assumption that device
side buffers should be the limiting factor. However, many
modern high speed LTE modems suffers from buffer-bloat,
making this assumption fail. This results in sub-optimal
performance due to excessive coalescing. And in cases where
such modems are connected to cheap embedded hosts there is
often severe buffer allocation issues, giving very noticeable
performance degradation .
A start on improving this is going from build time hard
coded limits to per device user configurable limits. The
ethtool coalescing API was selected as user interface
because, although the tuned values are buffer sizes, these
settings directly control datagram coalescing.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Finish the rx_max/tx_max setup by flushing buffers and
informing usbnet about the changes. This way, the settings
can be modified while the netdev is up and running.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have split out the part of the device setup
which MUST be done with the data interface in altsetting 0,
we can delay the rest of the initialization. This allows us
to move some of post-init buffer size config from bind to
the appropriate setup function.
The purpose of this refactoring is to collect all code
adjusting the rx_max and tx_max buffers in one place, so
that it is easier to call it from multiple call sites.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split the parts of setup dealing with device initialization from
parts just setting defaults for attributes which might be
changed after initialization.
Some commands of the device initialization are only allowed when
the data interface is in its disabled altsetting, so we must
separate them out of we are to allow rerunning parts of setup.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split out the part of setup dealing with updating the rx_max
and tx_max buffer sizes so that this code can be reused for
dynamically updating the limits.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
The NCM class match in the cdc_mbim driver is confusing and
cause unexpected behaviour. The USB core guarantees that a
USB interface is in altsetting 0 when probing starts. This
means that devices implementing a NCM 1.0 backwards
compatible MBIM function (a "NCM/MBIM function") always hit
the NCM entry in the cdc_mbim driver match table. Such
functions will never match any of the MBIM entries.
This causes unexpeced behaviour for cases where the NCM and
MBIM entries are differet, which is currently the case for
all except Ericsson devices.
Improve the probing of NCM/MBIM functions by looking up the
device again in the cdc_mbim match table after switching to
the MBIM identity.
The shared altsetting selection is updated to better
accommodate the new probing logic, returning the preferred
altsetting for the control interface instead of the data
interface. The control interface altsetting update is moved
to the cdc_mbim driver. It is never necessary to change the
control interface altsetting for NCM.
Cc: Greg Suarez <gsuarez@smithmicro.com>
Reported by: Yu-an Shih <yshih@nvidia.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
DSS VLANs are pseudo network interfaces representing arbitrary
data streams, and specifically not IP. Preventing spurious IP
packets can sometimes be a hassle. The kernel will for example
send an IPv6 Router Solicit when the interface is brought up
unless the user has been careful enough to disable IPv6 first.
Such packets forwared to a MBIM DSS session will look like
spurious noise to the device, and can cause it to log an error
or even malfunction.
Drop all IP packets on the designated DSS VLANs to prevent such
unwanted spurious transmissions.
Cc: Greg Suarez <gsuarez@smithmicro.com>
Reported-by: Arnaud Desmier <adesmier@sequans.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cdc_mbim driver maps 802.1q VLANs to MBIM IP and DSS
sessions. MBIM IP session 0 is handled as an exception and
is mapped to untagged frames.
This patch adds optional support for remapping MBIM IP
session 0 to 802.1q VLAN ID 4094 instead. The default
behaviour is not changed. The new behaviour is triggered
by adding a link for this previously unsupported VLAN.
The untagged mapping was chosen initially to support the
assumed most common use case: Most current MBIM devices only
support a single IP session (i.e. session 0 only), and using
untagged frames lets the users completely ignore the
additonal complexity of the multiplexing layer.
But when the multiplexing features of MBIM are used, then
this netdev gets a double meaning: It becomes the master
interface for all the VLAN subdevs the additional sessions
are mapped to, while still serving as the untagged IP
interface for session 0.
This can be problematic, especially when using Device Service
Streams (DSS), as have become apparent recently with the
availability of devices with real DSS support. Some use cases
need to e.g set a MTU which is higher than allowed for IP
Session 0. The dual role also leads to the situation where
the IP Session 0 interface cannot be taken down without
breaking unrelated IP or DSS sessions - a devastating side
effect which applications managing a simple IP session cannot
be expected to be aware of. A typical DHCP client will assume
that it should bring the interface down after releasing the
IP lease.
These problems can be avoided by tagging IP session 0 packets
too, making this session similar to all other multiplexed
sessions. This redefines the main netdev as an upper master
interface only.
Cc: Greg Suarez <gsuarez@smithmicro.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
net: get rid of SET_ETHTOOL_OPS
Dave Miller mentioned he'd like to see SET_ETHTOOL_OPS gone.
This does that.
Mostly done via coccinelle script:
@@
struct ethtool_ops *ops;
struct net_device *dev;
@@
- SET_ETHTOOL_OPS(dev, ops);
+ dev->ethtool_ops = ops;
Compile tested only, but I'd seriously wonder if this broke anything.
Suggested-by: Dave Miller <davem@davemloft.net>
Signed-off-by: Wilfried Klaebe <w-lkml@lebenslange-mailadresse.de>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The __vlan_find_dev_deep should always called in RCU, according
David's suggestion, rename to __vlan_find_dev_deep_rcu looks more
reasonable.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver maps 802.1q VLANs to MBIM sessions. The mapping is based on
a bogus assumption that all tagged frames will use the acceleration API
because we enable NETIF_F_HW_VLAN_CTAG_TX. This fails for e.g. frames
tagged in userspace using packet sockets. Such frames will erroneously
be considered as untagged and silently dropped based on not being IP.
Fix by falling back to looking into the ethernet header for a tag if no
accelerated tag was found.
Fixes: a82c7ce5bc ("net: cdc_ncm: map MBIM IPS SessionID to VLAN ID")
Cc: Greg Suarez <gsuarez@smithmicro.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 4d619f625a ("net: cdc_ncm: no point in filling up the NTBs
if we send ZLPs") changed the padding logic for devices with the ZLP
flag set. This meant that frames of any size will be sent without
additional padding, except for the single byte added if the size is
a multiple of the USB packet size. But if the unpadded size is
identical to the maximum frame size, and the maximum size is a
multiplum of the USB packet size, then this one-byte padding will
overflow the buffer.
Prevent padding if already at maximum frame size, letting usbnet
transmit a ZLP instead in this case.
Fixes: 4d619f625a ("net: cdc_ncm: no point in filling up the NTBs if we send ZLPs")
Reported by: Yu-an Shih <yshih@nvidia.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dan writes:
"The Dell drivers use the same configuration for PIDs:
81A2: Dell Wireless 5806 Gobi(TM) 4G LTE Mobile Broadband Card
81A3: Dell Wireless 5570 HSPA+ (42Mbps) Mobile Broadband Card
81A4: Dell Wireless 5570e HSPA+ (42Mbps) Mobile Broadband Card
81A8: Dell Wireless 5808 Gobi(TM) 4G LTE Mobile Broadband Card
81A9: Dell Wireless 5808e Gobi(TM) 4G LTE Mobile Broadband Card
These devices are all clearly Sierra devices, but are also definitely
Gobi-based. The A8 might be the MC7700/7710 and A9 is likely a MC7750.
>From DellGobi5kSetup.exe from the Dell drivers:
usbif0: serial/firmware loader?
usbif2: nmea
usbif3: modem/ppp
usbif8: net/QMI"
Reported-by: AceLan Kao <acelan.kao@canonical.com>
Reported-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
A number of older CMOTech modems are based on Qualcomm
chips and exporting a QMI/wwan function.
Reported-by: Lars Melin <larsm17@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the device is unplugged, the driver would try to disable the
device. Add checking the flag of RTL8152_UNPLUG to skip setting
the device when it is unplugged. This could shorten the time of
unloading the driver.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This device provides QMI and ethernet functionality via a standard CDC
ethernet descriptor. But when driven by cdc_ether, the QMI
functionality is unavailable because only cdc_ether can claim the USB
interface. Thus blacklist the device in cdc_ether and add its IDs to
qmi_wwan, which enables both QMI and ethernet simultaneously.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/marvell/mvneta.c
The mvneta.c conflict is a case of overlapping changes,
a conversion to devm_ioremap_resource() vs. a conversion
to netdev_alloc_pcpu_stats.
Signed-off-by: David S. Miller <davem@davemloft.net>
