There's no need to print the PCI resource
length and base address, nor the hardware
revision ID (which can be found in lspci)
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no reason to print these all the time,
the messages aren't all that interesting. Leave
them as DEBUG_INFO though, just in case.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the EEPROM reading was successful, don't print
a message by default, the EEPROM version isn't all
that interesting. Change the message to DEBUG_INFO
priority so it can still be obtained.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
People tend not to set the fields they want to leave as 0.
So make sure the struct is zeroed properly.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The ALIVE response of new fw inclues the base address of
the SCD in SRAM. Until we read it from a prph register,
which was set by the fw. Since the fw might well stop
updating the prph register, add a WARN when there is an
inconsitency between the ALIVE response and the register
to catch any change in the behavior.
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of open-coding it with a temporary list_head
pointer, just use list_first_entry.
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The flush_control parameter to iwlagn_txfifo_flush
is passed as an internal value (context flags) and
then sent to the device, that can't be right.
Fix the confusion by removing the parameter, always
use IWL_DROP_ALL that is redefined according to the
firmware API in the flush control.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no reason to clear the CTL_AMPDU flag on
transmitted frame status, it's not used by the
driver here and mac80211 only uses it for some
rate statistics.
Also remove a stray space in the function.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The flush command really flushes queues, not
FIFOs, and the first 32 bits indicate the
queues to flush, not FIFOs. Change the command
accordingly.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When we unregister from mac80211 it will down the device anyway.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
No HCMD can be sent while RFKILL is asserted. If a SYNC
command is running while RFKILL is asserted the fw will
silently discard it. This means that the driver needs to
wake the process that sleeps on the CMD_SYNC.
Since the RFKILL interrupt is handled in the transport layer
and the code that sleeps in CMD_SYNC is also in the transport
layer, all this logic can be handled there.
This simplifies the work of the op_mode.
So the transport layer will now return -ERFKILL when a CMD
is sent and RFKILL is asserted. This will be the case even
when the CMD is SYNC. The transport layer will return
-ERFKILL straight away.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Clarify the documentation to indicate that these
flags can only be used at the end, i.e. after them
a copy TFD (no flags set) is invalid.
Reported-by: Inbal Hacohen <inbal.hacohen@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In addition to the NOCOPY flag, add a DUP flag that
tells the transport to kmemdup() the buffer and free
it after the command completes.
Currently this is only supported for a single buffer
in a given command, but that could be extended if it
should be needed.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Remove the Kconfig option CONFIG_IWLWIFI_EXPERIMENTAL_MFP,
if the firmware doesn't support MFP then the user shouldn't
have the option to enable it as it won't work correctly.
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since the queue might not be empty, we need to free the
pending Tx packets.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This can happen when we shut down suddenly an interface.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Once in bus enumeration is enough, no need to print it
again when the op_mode loads.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Doing the opposite is wrong, the SCD wouldn't like someone
to clear its data while the queue is still active.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of hardcoding the expression, use the macro
provided in the previous patch.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When we disable a queue, we don't want the SCD to remember anything
about this queue (what packet was transmitted but not acked, what
packed was acked etc...).
Wipe out all this data in its SRAM.
Constify the arguments to iwl_write_targ_mem_dwords on the way.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Remove a number of variables that are assigned, but not used.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When tracing in iwlwifi, we get all data. Most of
the time, we don't need it, and it just takes up
a lot of extra space in the trace.
Make this optional by recording the data into two
separate trace events if it is needed. Without it,
record only the content of non-data and EAPOL TX
frames.
As a result, tracing without the data tracepoints
will record meta information including the 802.11
headers for all frames but will not record the
contents of data frames to reduce trace overhead.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When warning about a command that is too large,
print out the command name/ID to help figure
out which place is attempting to send a command
that is too large.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
"discard" support, some dm-raid improvements and other assorted
bits and pieces.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=XRmL
-----END PGP SIGNATURE-----
Merge tag 'md-3.7' of git://neil.brown.name/md
Pull md updates from NeilBrown:
- "discard" support, some dm-raid improvements and other assorted bits
and pieces.
* tag 'md-3.7' of git://neil.brown.name/md: (29 commits)
md: refine reporting of resync/reshape delays.
md/raid5: be careful not to resize_stripes too big.
md: make sure manual changes to recovery checkpoint are saved.
md/raid10: use correct limit variable
md: writing to sync_action should clear the read-auto state.
Subject: [PATCH] md:change resync_mismatches to atomic64_t to avoid races
md/raid5: make sure to_read and to_write never go negative.
md: When RAID5 is dirty, force reconstruct-write instead of read-modify-write.
md/raid5: protect debug message against NULL derefernce.
md/raid5: add some missing locking in handle_failed_stripe.
MD: raid5 avoid unnecessary zero page for trim
MD: raid5 trim support
md/bitmap:Don't use IS_ERR to judge alloc_page().
md/raid1: Don't release reference to device while handling read error.
raid: replace list_for_each_continue_rcu with new interface
add further __init annotations to crypto/xor.c
DM RAID: Fix for "sync" directive ineffectiveness
DM RAID: Fix comparison of index and quantity for "rebuild" parameter
DM RAID: Add rebuild capability for RAID10
DM RAID: Move 'rebuild' checking code to its own function
...
Pull TPM bugfixes from James Morris.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
tpm: Propagate error from tpm_transmit to fix a timeout hang
driver/char/tpm: fix regression causesd by ppi
Pull ACPI & Thermal updates from Len Brown:
"The generic Linux thermal layer is gaining some new capabilities
(generic cooling via cpufreq) and some new customers (ARM).
Also, an ACPI EC bug fix plus a regression fix."
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux: (30 commits)
tools/power/acpi/acpidump: remove duplicated include from acpidump.c
ACPI idle, CPU hotplug: Fix NULL pointer dereference during hotplug
cpuidle / ACPI: fix potential NULL pointer dereference
ACPI: EC: Add a quirk for CLEVO M720T/M730T laptop
ACPI: EC: Make the GPE storm threshold a module parameter
thermal: Exynos: Fix NULL pointer dereference in exynos_unregister_thermal()
Thermal: Fix bug on cpu_cooling, cooling device's id conflict problem.
thermal: exynos: Use devm_* functions
ARM: exynos: add thermal sensor driver platform data support
thermal: exynos: register the tmu sensor with the kernel thermal layer
thermal: exynos5: add exynos5250 thermal sensor driver support
hwmon: exynos4: move thermal sensor driver to driver/thermal directory
thermal: add generic cpufreq cooling implementation
Fix a build error.
thermal: Fix potential NULL pointer accesses
thermal: add Renesas R-Car thermal sensor support
thermal: fix potential out-of-bounds memory access
Thermal: Introduce locking for cdev.thermal_instances list.
Thermal: Unify the code for both active and passive cooling
Thermal: Introduce simple arbitrator for setting device cooling state
...
Cleanups
Clean up compile warnings in kgdboc.c and x86/kernel/kgdb.c
Add module event hooks for simplified debugging with gdb
Fixes
Fix kdb to stop paging with 'q' on bta and dmesg
Fix for data that scrolls off the vga console due to line wrapping
when using the kdb pager
New
The debug core registers for kernel module events which allows a
kernel aware gdb to automatically load symbols and break on entry
to a kernel module
Allow kgdboc=kdb to setup kdb on the vga console
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=uf0L
-----END PGP SIGNATURE-----
Merge tag 'for_linus-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/kgdb
Pull KGDB/KDB fixes and cleanups from Jason Wessel:
"Cleanups
- Clean up compile warnings in kgdboc.c and x86/kernel/kgdb.c
- Add module event hooks for simplified debugging with gdb
Fixes
- Fix kdb to stop paging with 'q' on bta and dmesg
- Fix for data that scrolls off the vga console due to line wrapping
when using the kdb pager
New
- The debug core registers for kernel module events which allows a
kernel aware gdb to automatically load symbols and break on entry
to a kernel module
- Allow kgdboc=kdb to setup kdb on the vga console"
* tag 'for_linus-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/kgdb:
tty/console: fix warnings in drivers/tty/serial/kgdboc.c
kdb,vt_console: Fix missed data due to pager overruns
kdb: Fix dmesg/bta scroll to quit with 'q'
kgdboc: Accept either kbd or kdb to activate the vga + keyboard kdb shell
kgdb,x86: fix warning about unused variable
mips,kgdb: fix recursive page fault with CONFIG_KPROBES
kgdb: Add module event hooks
provisioning and factor the bio_prison code out into a separate
module (for sharing with the forthcoming cache target).
Use struct bio's front_pad to eliminate the use of one separate mempool
by bio-based devices.
A few other tiny clean-ups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=ft64
-----END PGP SIGNATURE-----
Merge tag 'dm-3.7-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm
Pull device-mapper changes from Alasdair G Kergon:
"Remove the power-of-2 block size constraint on discards in dm thin
provisioning and factor the bio_prison code out into a separate module
(for sharing with the forthcoming cache target).
Use struct bio's front_pad to eliminate the use of one separate
mempool by bio-based devices.
A few other tiny clean-ups."
* tag 'dm-3.7-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm:
dm: store dm_target_io in bio front_pad
dm thin: move bio_prison code to separate module
dm thin: prepare to separate bio_prison code
dm thin: support discard with non power of two block size
dm persistent data: convert to use le32_add_cpu
dm: use ACCESS_ONCE for sysfs values
dm bufio: use list_move
dm mpath: fix check for null mpio in end_io fn
This is an assorted set of stragglers into the merge window with driver
updates for megaraid_sas, lpfc, bfi and mvumi. It also includes some fairly
major fixes for virtio-scsi (scatterlist init), scsi_debug (off by one error),
storvsc (use after free) and qla2xxx (potential deadlock).
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJQeJfDAAoJEDeqqVYsXL0MhqgH/Rq7ebKJvKcUoKsTJKsZ2H0V
iaK5wBvhPBXLxYF5fMEnOwOPT34ry4SWJ7IqTKQqZItx1kqZuG4OTUjmueUCxaMb
7ELFWqyV1z7lyt+XAvNt/RTdMFl3n2SkOxgQJ8kzTPYzEHcE8GCH+dtuqzxoOUqx
styM6DE9Y5cQR1ozacj/QDMv4gn2jclclYgaxR2OTqzqQFeTMzn5KfRH4b6vYtos
ZuYlFE4uaAQhsUGeOqTcGlMvot4tyz4KGO4oy4xkHRQXRVQ52Ve8slRr1z4EUJ3H
rOpz869Y97vnSDFyXuJDa8PpbDd5KOU1uJBxE/3LlCoXIQj4u71hDXETRtq8jtg=
=T50d
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull misc SCSI updates from James Bottomley:
"This is an assorted set of stragglers into the merge window with
driver updates for megaraid_sas, lpfc, bfi and mvumi. It also
includes some fairly major fixes for virtio-scsi (scatterlist init),
scsi_debug (off by one error), storvsc (use after free) and qla2xxx
(potential deadlock).
Signed-off-by: James Bottomley <JBottomley@Parallels.com>"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (49 commits)
[SCSI] storvsc: Account for in-transit packets in the RESET path
[SCSI] qla2xxx: fix potential deadlock on ha->hardware_lock
[SCSI] scsi_debug: Fix off-by-one bug when unmapping region
[SCSI] Shorten the path length of scsi_cmd_to_driver()
[SCSI] virtio-scsi: support online resizing of disks
[SCSI] virtio-scsi: fix LUNs greater than 255
[SCSI] virtio-scsi: initialize scatterlist structure
[SCSI] megaraid_sas: Version, Changelog, Copyright update
[SCSI] megaraid_sas: Remove duplicate code
[SCSI] megaraid_sas: Add SystemPD FastPath support
[SCSI] megaraid_sas: Add array boundary check for SystemPD
[SCSI] megaraid_sas: Load io_request DataLength in bytes
[SCSI] megaraid_sas: Add module param for configurable MSI-X vector count
[SCSI] megaraid_sas: Remove un-needed completion_lock spinlock calls
[SCSI] lpfc 8.3.35: Update lpfc version for 8.3.35 driver release
[SCSI] lpfc 8.3.35: Fixed not reporting logical link speed to SCSI midlayer when QoS not on
[SCSI] lpfc 8.3.35: Fix error with fabric service parameters causing performance issues
[SCSI] lpfc 8.3.35: Fixed SCSI host create showing wrong link speed on SLI3 HBA ports
[SCSI] lpfc 8.3.35: Fixed not checking solicition in progress bit when verifying FCF record for use
[SCSI] lpfc 8.3.35: Fixed messages for misconfigured port errors
...
Pull input layer updates from Dmitry Torokhov:
"2nd round of updates for the input subsystem. With it input core no
longer limits number of character devices per event handler (such as
evdev) to 32, but switches to dynamic minors once legacy range is
exhausted. This should get multi-seat installations that currently
run our of event devices very quickly.
You will also get an update for Wacom driver and a couple of driver
fixes."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: extend the number of event (and other) devices
Input: mousedev - mark mousedev interfaces as non-seekable
Input: mousedev - rename mixdev_open to opened_by_mixdev
Input: mousedev - reformat structure initializers
Input: mousedev - factor out psaux code to reduce #ifdefery
Input: samsung-keypad - add clk_prepare and clk_unprepare
Input: atmel_mxt_ts - simplify mxt_dump_message
Input: wacom - clean up wacom_query_tablet_data
Input: wacom - introduce wacom_fix_phy_from_hid
Input: wacom - allow any multi-input Intuos device to set prox
Input: wacom - report correct touch contact size for I5/Bamboo
Pull networking updates from David Miller:
1) Alexey Kuznetsov noticed we routed TCP resets improperly in the
assymetric routing case, fix this by reverting a change that made us
use the incoming interface in the outgoing route key when we didn't
have a socket context to work with.
2) TCP sysctl kernel memory leakage to userspace fix from Alan Cox.
3) Move UAPI bits from David Howells, WIMAX and CAN this time.
4) Fix TX stalls in e1000e wrt. Byte Queue Limits, from Hiroaki
SHIMODA, Denys Fedoryshchenko, and Jesse Brandeburg.
5) Fix IPV6 crashes in packet generator module, from Amerigo Wang.
6) Tidies and fixes in the new VXLAN driver from Stephen Hemminger.
7) Bridge IP options parse doesn't check first if SKB header has at
least an IP header's worth of content present. Fix from Sarveshwar
Bandi.
8) The kernel now generates compound pages on transmit and the Xen
netback drivers needs some adjustments in order to handle this. Fix
from Ian Campbell.
9) Turn off ASPM in JME driver, from Kevin Bardon and Matthew Garrett.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (43 commits)
mcs7830: Fix link state detection
net: add doc for in4_pton()
net: add doc for in6_pton()
vti: fix sparse bit endian warnings
tcp: resets are misrouted
usbnet: Support devices reporting idleness
Add CDC-ACM support for the CX93010-2x UCMxx USB Modem
net/ethernet/jme: disable ASPM
tcp: sysctl interface leaks 16 bytes of kernel memory
kaweth: print correct debug ptr
e1000e: Change wthresh to 1 to avoid possible Tx stalls
ipv4: fix route mark sparse warning
xen: netback: handle compound page fragments on transmit.
bridge: Pull ip header into skb->data before looking into ip header.
isdn: fix a wrapping bug in isdn_ppp_ioctl()
vxlan: fix oops when give unknown ifindex
vxlan: fix receive checksum handling
vxlan: add additional headroom
vxlan: allow configuring port range
vxlan: associate with tunnel socket on transmit
...
Use the recently-added bio front_pad field to allocate struct dm_target_io.
Prior to this patch, dm_target_io was allocated from a mempool. For each
dm_target_io, there is exactly one bio allocated from a bioset.
This patch merges these two allocations into one allocation: we create a
bioset with front_pad equal to the size of dm_target_io so that every
bio allocated from the bioset has sizeof(struct dm_target_io) bytes
before it. We allocate a bio and use the bytes before the bio as
dm_target_io.
_tio_cache is removed and the tio_pool mempool is now only used for
request-based devices.
This idea was introduced by Kent Overstreet.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: Kent Overstreet <koverstreet@google.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: tj@kernel.org
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Bill Pemberton <wfp5p@viridian.itc.virginia.edu>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
The bio prison code will be useful to other future DM targets so
move it to a separate module.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
The bio prison code will be useful to share with future DM targets.
Prepare to move this code into a separate module, adding a dm prefix
to structures and functions that will be exported.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Support discards when the pool's block size is not a power of 2.
The block layer assumes discard_granularity is a power of 2 (in
blkdev_issue_discard), so we set this to the largest power of 2 that is
a divides into the number of sectors in each block, but never less than
DATA_DEV_BLOCK_SIZE_MIN_SECTORS.
This patch eliminates the "Discard support must be disabled when the
block size is not a power of 2" constraint that was imposed in commit
55f2b8b ("dm thin: support for non power of 2 pool blocksize"). That
commit was incomplete: using a block size that is not a power of 2
shouldn't mean disabling discard support on the device completely.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
The device had an undocumented "feature": it can provide a sequence of
spurious link-down status data even if the link is up all the time.
A sequence of 10 was seen so update the link state only after the device
reports the same link state 20 times.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Reported-by: Michael Leun <lkml20120218@newton.leun.net>
Tested-by: Michael Leun <lkml20120218@newton.leun.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert cpu_to_le32(le32_to_cpu(E1) + E2) to use le32_add_cpu().
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Use the ACCESS_ONCE macro in dm-bufio and dm-verity where a variable
can be modified asynchronously (through sysfs) and we want to prevent
compiler optimizations that assume that the variable hasn't changed.
(See Documentation/atomic_ops.txt.)
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Use list_move() instead of list_del() + list_add().
spatch with a semantic match was used to find this.
(http://coccinelle.lip6.fr/)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
The mpio dereference should be moved below the BUG_ON NULL test
in multipath_end_io().
spatch with a semantic match was used to found this.
(http://coccinelle.lip6.fr/)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
- Register a pfn_is_ram helper to speed up reading of /proc/vmcore.
Bug-fixes:
- Three pvops call for Xen were undefined causing BUG_ONs.
- Add a quirk so that the shutdown watches (used by kdump) are not used with older Xen (3.4).
- Fix ungraceful state transition for the HVC console.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJQeBKDAAoJEFjIrFwIi8fJDpwH/3nPBH82pJVxdLPBnmJhWuJR
voSPP0m9i69w/mc7wHtiRwK4lRMAUidgS77iBZkIT2cY0/NYvOKKBlMUitkYJFlK
dTVqr9O4iQcuG2yQk8+mXxC6NLH1VKOnSIyhqRswrePoBKzoHi/x7Y462a+tbxa9
lGBHT9/SqeYXyItRfkdfmAXFZcqIJqLRXEwRMvbky1U3s2QGy7CdIQgra0zWF+t1
ashNpaEBpH9Jy60VSpQtMpx8hWxd0W2NirNu+nACtTE5/MeuiBvKlPdEPC/rUbdJ
c5j5VYLjSxPCheY0sajK6pxKgHdfiqmMRlutzMVj3Egwilb0LBxv1018gRFzBu8=
=/qCG
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.7-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull Xen fixes from Konrad Rzeszutek Wilk:
"This has four bug-fixes and one tiny feature that I forgot to put
initially in my tree due to oversight.
The feature is for kdump kernels to speed up the /proc/vmcore reading.
There is a ram_is_pfn helper function that the different platforms can
register for. We are now doing that.
The bug-fixes cover some embarrassing struct pv_cpu_ops variables
being set to NULL on Xen (but not baremetal). We had a similar issue
in the past with {write|read}_msr_safe and this fills the three
missing ones. The other bug-fix is to make the console output (hvc)
be capable of dealing with misbehaving backends and not fall flat on
its face. Lastly, a quirk for older XenBus implementations that came
with an ancient v3.4 hypervisor (so RHEL5 based) - reading of certain
non-existent attributes just hangs the guest during bootup - so we
take precaution of not doing that on such older installations.
Feature:
- Register a pfn_is_ram helper to speed up reading of /proc/vmcore.
Bug-fixes:
- Three pvops call for Xen were undefined causing BUG_ONs.
- Add a quirk so that the shutdown watches (used by kdump) are not
used with older Xen (3.4).
- Fix ungraceful state transition for the HVC console."
* tag 'stable/for-linus-3.7-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/pv-on-hvm kexec: add quirk for Xen 3.4 and shutdown watches.
xen/bootup: allow {read|write}_cr8 pvops call.
xen/bootup: allow read_tscp call for Xen PV guests.
xen pv-on-hvm: add pfn_is_ram helper for kdump
xen/hvc: handle backend CLOSED without CLOSING
The commit 254d1a3f02, titled
"xen/pv-on-hvm kexec: shutdown watches from old kernel" assumes that the
XenBus backend can deal with reading of values from:
"control/platform-feature-xs_reset_watches":
... a patch for xenstored is required so that it
accepts the XS_RESET_WATCHES request from a client (see changeset
23839:42a45baf037d in xen-unstable.hg). Without the patch for xenstored
the registration of watches will fail and some features of a PVonHVM
guest are not available. The guest is still able to boot, but repeated
kexec boots will fail."
Sadly this is not true when using a Xen 3.4 hypervisor and booting a PVHVM
guest. We end up hanging at:
err = xenbus_scanf(XBT_NIL, "control",
"platform-feature-xs_reset_watches", "%d", &supported);
This can easily be seen with guests hanging at xenbus_init:
NX (Execute Disable) protection: active
SMBIOS 2.4 present.
DMI: Xen HVM domU, BIOS 3.4.0 05/13/2011
Hypervisor detected: Xen HVM
Xen version 3.4.
Xen Platform PCI: I/O protocol version 1
... snip ..
calling xenbus_init+0x0/0x27e @ 1
Reverting the commit or using the attached patch fixes the issue. This fix
checks whether the hypervisor is older than 4.0 and if so does not try to
perform the read.
Fixes-Oracle-Bug: 14708233
CC: stable@vger.kernel.org
Acked-by: Olaf Hering <olaf@aepfle.de>
[v2: Added a comment in the source code]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
It is possible to miss data when using the kdb pager. The kdb pager
does not pay attention to the maximum column constraint of the screen
or serial terminal. This result is not incrementing the shown lines
correctly and the pager will print more lines that fit on the screen.
Obviously that is less than useful when using a VGA console where you
cannot scroll back.
The pager will now look at the kdb_buffer string to see how many
characters are printed. It might not be perfect considering you can
output ASCII that might move the cursor position, but it is a
substantially better approximation for viewing dmesg and trace logs.
This also means that the vt screen needs to set the kdb COLUMNS
variable.
Cc: <stable@vger.kernel.org>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
It is a common enough mistake for people to specify "kdb" when they
meant to type "kbd" that the kgdboc can just accept both since they
both mean the same thing anyway. Specifically it is for the case
where you want kdb to be active on your graphics console + keyboard
(where kbd was the original abbreviation for keyboard).
With this change kgdboc will now accept either to mean the same thing:
kgdboc=kbd
kgdboc=kdb
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Pull second set of media updates from Mauro Carvalho Chehab:
"Despite its size, most of the stuff here is trivial. This series
contains:
- s5p-mfc: additions at the driver and at the core to support H.264
hardware codec;
- Some improvements at s5p and davinci embedded drivers;
- Some V4L2 compliance fixes applied on a few drivers;
- Several random trivial patches, including several fixes and a few
new board support additions;
Notes:
1) Some Exynos media patches were dependent on some -arm fixes that
got merged on changeset 782cd9e. That's why this pull request is
based that changeset.
2) As promised, I reviewed the pending VB2 DMABUF series.
While setting a test environment, it was noticed that the upstream
support for Samsung Exynos 4 boards (smdk310 and Origen) are
broken upstream, likely due to regressions: both defconfigs are
wrong and regulator settings for both boards are broken. That,
allied with some bug at the dummy regulator driver, causes OOPSes
during boot time.
Long story short: even fixing the above, the proposed patches
OOPSed when running the DMABUF test. Not sure yet if the OOPSes
are due to some other undetected regressions, or due to some bug
on the patches.
Due to the above, DMABUF patches for vb2 got NACKed for 3.7."
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (109 commits)
[media] m5mols: Add missing #include <linux/sizes.h>
[media] stk1160: Add support for S-Video input
Revert "[media] omap3isp: Replace cpu_is_omap3630() with ISP revision check"
[media] dvb: LNA implementation changes
[media] v4l2-ioctl: fix W=1 warnings
[media] v4l2-ioctl: add blocks check for VIDIOC_SUBDEV_G/S_EDID
[media] omap3isp: Fix compilation error in ispreg.h
[media] rc-msi-digivox-ii: Add full scan keycodes
[media] cx25821: testing the wrong variable
[media] tda18271-common: hold the I2C adapter during write transfers
[media] ds3000: add module parameter to force firmware upload
[media] drivers/media: Remove unnecessary semicolon
[media] winbond: remove space from driver name
[media] iguanair: cannot send data from the stack
[media] omap3isp: Replace cpu_is_omap3630() with ISP revision check
[media] dvb-usb: print small buffers via %*ph
[media] uvc: Add return code check at vb2_queue_init()
[media] em28xx: Replace memcpy with struct assignment
[media] bt8xx: Add video4linux control V4L2_CID_COLOR_KILLER
[media] mem2mem_testdev: Use devm_kzalloc() in probe
...
Conflicts:
arch/arm/mach-davinci/include/mach/da8xx.h
- Complement the Nomadik pinctrl driver with alternate Cx functions
so it handles all oddities.
- A patch to the IRQdomain to reform the simple irqdomain to handle
IRQ descriptor allocation dynamically.
- Use the above feature in the Nomadik pin controller.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=UKY/
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-for-3.7-late' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull second set of pinctrl patches from Linus Walleij:
"Here is a late pinctrl pull request with stuff that wasn't quite
tested at the first pull request.
The main reason to not hold off is that the modifications to
irq_domain_add_simple() as reviewed by Rob Herring introduce new
infrastructure for irqdomains that will be useful for the next cycle:
instead of sprinkling irq descriptor allocation all over the kernel
wherever a "legacy" domain is registered, which is necessary for any
platform using sparse IRQs, and many irq chips are say GPIO
controllers which may be used with several systems, some with sparse
IRQs some not, we push this into the irq_domain_add_simple() so we can
atleast do mistakes in one place.
The irq_domain_add_simple() is currently unused in the kernel, so I
need to provide a user. The Nomadik stuff that goes with are changes
to the driver I use day-to-day to make use of this facility (and a
dependency), so see it as a way to eat my own dogfood: if this blows
up the egg hits my face.
A second round of pinctrl patches for v3.7:
- Complement the Nomadik pinctrl driver with alternate Cx functions
so it handles all oddities.
- A patch to the IRQdomain to reform the simple irqdomain to handle
IRQ descriptor allocation dynamically.
- Use the above feature in the Nomadik pin controller."
* tag 'pinctrl-for-3.7-late' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl/nomadik: use simple or linear IRQ domain
irqdomain: augment add_simple() to allocate descs
pinctrl/nomadik: support other alternate-C functions
It includes:
- large updates for OMAP
- basic OMAP5 DSS support for DPI and DSI outputs
- large cleanups and restructuring
- some update to Exynos and da8xx-fb
- removal of the pnx4008 driver (arch removed)
- various other small patches
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.12 (GNU/Linux)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=EJUS
-----END PGP SIGNATURE-----
Merge tag 'fbdev-updates-for-3.7' of git://github.com/schandinat/linux-2.6
Pull fbdev updates from Florian Tobias Schandinat:
"This includes:
- large updates for OMAP
- basic OMAP5 DSS support for DPI and DSI outputs
- large cleanups and restructuring
- some update to Exynos and da8xx-fb
- removal of the pnx4008 driver (arch removed)
- various other small patches"
Fix up some trivial conflicts (mostly just include line changes, but
also some due to the renaming of the deferred work functions by Tejun).
* tag 'fbdev-updates-for-3.7' of git://github.com/schandinat/linux-2.6: (193 commits)
gbefb: fix compile error
video: mark nuc900fb_map_video_memory as __devinit
video/mx3fb: set .owner to prevent module unloading while being used
video: exynos_dp: use clk_prepare_enable and clk_disable_unprepare
drivers/video/exynos/exynos_mipi_dsi.c: fix error return code
drivers/video/savage/savagefb_driver.c: fix error return code
video: s3c-fb: use clk_prepare_enable and clk_disable_unprepare
da8xx-fb: save and restore LCDC context across suspend/resume cycle
da8xx-fb: add pm_runtime support
video/udlfb: fix line counting in fb_write
OMAPDSS: add missing include for string.h
OMAPDSS: DISPC: Configure color conversion coefficients for writeback
OMAPDSS: DISPC: Add manager like functions for writeback
OMAPDSS: DISPC: Configure writeback FIFOs
OMAPDSS: DISPC: Configure writeback specific parameters in dispc_wb_setup()
OMAPDSS: DISPC: Configure overlay-like parameters in dispc_wb_setup
OMAPDSS: DISPC: Add function to set channel in for writeback
OMAPDSS: DISPC: Don't set chroma resampling bit for writeback
OMAPDSS: DISPC: Downscale chroma if plane is writeback
OMAPDSS: DISPC: Configure input and output sizes for writeback
...
The following error appeared due to a merge problem; the patches:
fc108d24 "mmc: mxs-mmc: fix deadlock caused by recursion loop"
829c1bf4 "mmc: spi: Pull out parts shared between MMC and SPI"
came in through separate branches and cause this build error when
combined.
drivers/mmc/host/mxs-mmc.c: In function 'mxs_mmc_enable_sdio_irq':
drivers/mmc/host/mxs-mmc.c:527:3: error: 'struct mxs_mmc_host' has no member named 'base'
drivers/mmc/host/mxs-mmc.c:527:3: error: 'struct mxs_mmc_host' has no member named 'devid'
make[3]: *** [drivers/mmc/host/mxs-mmc.o] Error 1
This patch corrects the issue.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Some device types support a form of power management in which
the device suggests to the host that the device may be suspended
now. Support for that is best located in usbnet.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
