TI CPDMA currently uses a bitmap for tracking descriptors alloactions
allocations, but The genalloc already handles the same and can be used
as with special memory (SRAM) as with DMA cherent memory chank
(dma_alloc_coherent()). Hence, switch to using genalloc and add
desc_num property for each channel for limitation of max number of
allowed descriptors for each CPDMA channel. This patch do not affect
on net throuput.
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Tested-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marvell 88E1111 currently uses the generic marvell config ANEG function.
This function has a sequence accessing Page 5 and Register 31,
both of which are not defined or reserved for this PHY.
Hence this patch adds a new config ANEG function for Marvell 88E1111
without these erroneous accesses.
Signed-off-by: Harini Katakam <harinik@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sven Eckelmann says:
====================
batman-adv: Fixes for Linux 4.7
Antonio currently seems to be occupied. This is currently rather unfortunate
because there are patches waiting in the batman-adv development repository
maint(enance) branch [1] since up to 6 weeks. I am now getting asked when
these patches will hit the distribution kernels and therefore decided to
submit these patches directly to netdev.
The patch from Simon works around the problem that warnings could be triggered
in the translation table code via packets using a VLAN not configured on the
target host. This warning was replaced with a rate limited info message.
Ben Hutchings found an superfluous batadv_softif_vlan_put in the error
handling code of the translation table while he backported the "batman-adv:
Fix reference counting of vlan object for tt_local_entry" patch to the stable
kernels. He noticed correctly that this batadv_softif_vlan_put should also
have been removed by the said patch.
The most requested fix at the moment is related to a double free in the
translation table code. It is a race condition which mostly happens on systems
with multiple cores and multiple network interface attached to batman-adv. Two
Freifunk communities which were haunted by weird crashes (with backtraces
reporting problems in other parts of the kernel) were kind enough to test this
patch. They reported that there systems are now running stable after applying
this patch.
An invalid memory access was detected in the batadv_icmp_packet_rr handling
code when receiving a skbuff with fragments. The last patch is fixing a memory
leak when the interface is removed via .dellink. The code to fix it was copied
from the code handling the legacy sysfs interface to remove netdevices from a
batman-adv netdevice.
There are still 28 patches in the development tree for v4.8 but I will leave
them to Antonio because these are cleanups and features and therefore for net-
next.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The untagged vlan object is only destroyed when the interface is removed
via the legacy sysfs interface. But it also has to be destroyed when the
standard rtnl-link interface is used.
Fixes: 5d2c05b213 ("batman-adv: add per VLAN interface attribute framework")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Acked-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The skb_linearize may reallocate the skb. This makes the calculated pointer
for ethhdr invalid. But it the pointer is used later to fill in the RR
field of the batadv_icmp_packet_rr packet.
Instead re-evaluate eth_hdr after the skb_linearize+skb_cow to fix the
pointer and avoid the invalid read.
Fixes: da6b8c20a5 ("batman-adv: generalize batman-adv icmp packet handling")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each batadv_tt_local_entry hold a single reference to a
batadv_softif_vlan. In case a new entry cannot be added to the hash
table, the error path puts the reference, but the reference will also
now be dropped by batadv_tt_local_entry_release().
Fixes: a33d970d0b ("batman-adv: Fix reference counting of vlan object for tt_local_entry")
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tt_req_node is added and removed from a list inside a spinlock. But the
locking is sometimes removed even when the object is still referenced and
will be used later via this reference. For example batadv_send_tt_request
can create a new tt_req_node (including add to a list) and later
re-acquires the lock to remove it from the list and to free it. But at this
time another context could have already removed this tt_req_node from the
list and freed it.
CPU#0
batadv_batman_skb_recv from net_device 0
-> batadv_iv_ogm_receive
-> batadv_iv_ogm_process
-> batadv_iv_ogm_process_per_outif
-> batadv_tvlv_ogm_receive
-> batadv_tvlv_ogm_receive
-> batadv_tvlv_containers_process
-> batadv_tvlv_call_handler
-> batadv_tt_tvlv_ogm_handler_v1
-> batadv_tt_update_orig
-> batadv_send_tt_request
-> batadv_tt_req_node_new
spin_lock(...)
allocates new tt_req_node and adds it to list
spin_unlock(...)
return tt_req_node
CPU#1
batadv_batman_skb_recv from net_device 1
-> batadv_recv_unicast_tvlv
-> batadv_tvlv_containers_process
-> batadv_tvlv_call_handler
-> batadv_tt_tvlv_unicast_handler_v1
-> batadv_handle_tt_response
spin_lock(...)
tt_req_node gets removed from list and is freed
spin_unlock(...)
CPU#0
<- returned to batadv_send_tt_request
spin_lock(...)
tt_req_node gets removed from list and is freed
MEMORY CORRUPTION/SEGFAULT/...
spin_unlock(...)
This can only be solved via reference counting to allow multiple contexts
to handle the list manipulation while making sure that only the last
context holding a reference will free the object.
Fixes: a73105b8d4 ("batman-adv: improved client announcement mechanism")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Tested-by: Martin Weinelt <martin@darmstadt.freifunk.net>
Tested-by: Amadeus Alfa <amadeus@chemnitz.freifunk.net>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a VLAN tagged frame is received and the corresponding VLAN is not
configured on the soft interface, it will splat a WARN on every packet
received. This is a quite annoying behaviour for some scenarios, e.g. if
bat0 is bridged with eth0, and there are arbitrary VLAN tagged frames
from Ethernet coming in without having any VLAN configuration on bat0.
The code should probably create vlan objects on the fly and
transparently transport these VLAN-tagged Ethernet frames, but until
this is done, at least the WARN splat should be replaced by a rate
limited output.
Fixes: 354136bcc3 ("batman-adv: fix kernel crash due to missing NULL checks")
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we have a system which uses fixed PHY devices and calls
fixed_phy_register() then fixed_phy_unregister() we can exhaust the
number of fixed PHYs available after a while, since we keep incrementing
the variable phy_fixed_addr, but we never decrement it.
This patch fixes that by converting the fixed PHY allocation to using
IDA, which takes care of the allocation/dealloaction of the PHY
addresses for us.
Fixes: a759512174 ("net: phy: extend fixed driver with fixed_phy_register()")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Olga Kornievskaia reports that the following test fails to trigger
an OPEN_DOWNGRADE on the wire, and only triggers the final CLOSE.
fd0 = open(foo, RDRW) -- should be open on the wire for "both"
fd1 = open(foo, RDONLY) -- should be open on the wire for "read"
close(fd0) -- should trigger an open_downgrade
read(fd1)
close(fd1)
The issue is that we're missing a check for whether or not the current
state transitioned from an O_RDWR state as opposed to having transitioned
from a combination of O_RDONLY and O_WRONLY.
Reported-by: Olga Kornievskaia <aglo@umich.edu>
Fixes: cd9288ffae ("NFSv4: Fix another bug in the close/open_downgrade code")
Cc: stable@vger.kernel.org # 2.6.33+
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
The only users of audit_get_tty and audit_put_tty are internal to
audit, so move it out of include/linux/audit.h to kernel.h and create
a proper function rather than inlining it. This also reduces kABI
changes.
Suggested-by: Paul Moore <pmoore@redhat.com>
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
[PM: line wrapped description]
Signed-off-by: Paul Moore <paul@paul-moore.com>
Move the calculations of values after the allocation in case the
allocation fails. This avoids wasting effort in the rare case that it
fails, but more importantly saves us extra logic to release the tty
ref.
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Pull libata fixes from Tejun Heo:
"Two trivial fixes - one for a bug in the allocation failure path and
the other a compiler warning fix"
* 'for-4.7-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ata: sata_mv: fix mis-conversion in mv_write_cached_reg()
ata: fix return value check in ahci_seattle_get_port_info()
Pull HID fix from Jiri Kosina:
"Regression fix for multitouch palm rejection from Allen Hung"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: multitouch: enable palm rejection for Windows Precision Touchpad
Revert "HID: multitouch: enable palm rejection if device implements confidence usage"
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phydev in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phydev in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phydev in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phy in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Diag intends to broadcast tcp_sk and udp_sk socket destruction.
Testing sk->sk_protocol for IPPROTO_TCP/IPPROTO_UDP alone is not
sufficient for this. Raw sockets can have the same type.
Add a test for sk->sk_type.
Fixes: eb4cb00852 ("sock_diag: define destruction multicast groups")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Grygorii Strashko says:
====================
drivers: net: cpsw: improve runtime pm
This series intended to improve runtime PM and allow CPSW to be
RPM suspended when all ethX netdevices are down.
To achieve above goal it is required to relax runtime PM constraints for
Davinci MDIO which blocks CPSW runtime PM now, because Davinci MDIO is always
powered on during probe and powered off only when it's going to be removed.
- Patches 6-11 implement PM runtime autosuspend for Davinci MDIO, but keep it
disabled by default, because Davinci MDIO is integrated in big set of TI devices
and not all of them verified to work correctly with RPM autosuspend enabled:
expected to work on SoCs where MDIO is defined as part of CPSW in DT
(cpsw.c DRA7/am57x, am437x, am335x)
The CPSW need to be fixed before RPM suspended can be allowed:
- Patches 1-5 ensure that CPSW will not cause L3 errors while it is in RPM
suspended state.
Davinci MDIO RPM autosuspend can be enabled through sysfs:
echo 100 > /sys/devices/../48484000.ethernet/48485000.mdio/power/autosuspend_delay_ms
Patches 12 - 15: introduce new compatible string "ti,cpsw-mdio" which is used
then to enable RPM for am335x/am437x/dra7 SoCs.
Tested on am335x, am437x, am572x and k2g (on k2g with RPM disabled for Davinci MDIO)
These changes should not affect on errata i877 implementation on DRA7.
Power measurement on am335x GP EVM:
Without this series: 547.60 mW total SoC power
With this series + "ifconfig eth0 down": 477.32 mW Total Soc Power
Changes in v2:
- CPSW ethtool interface updated to use .begin()/.complete() callbacks
- kbuild failure fixed
- davinci_mdio DT updated with proper description of allowed compatible strings
combinations
Link on v1:
https://lkml.org/lkml/2016/6/15/362
====================
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add "ti,cpsw-mdio" for am335x/am437x/dra7 SoCs where MDIO is
implemented as part of TI CPSW and, this way, enable PM runtime auto
suspend for Davinci MDIO driver on these paltforms.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use "ti,cpsw-mdio" to enable PM runtime auto-suspend on supported
platforms, where MDIO is implemented as part of TI CPSW.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce "ti,cpsw-mdio" compatible string for Davinci MDIO, because
it's required to distinguish the case when MDIO is part of TI CPSW to
enable features supported by TI CPSW (for example, enable PM
management).
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Document missed "ti,am4372-mdio" compat string used for TI am437x SoC
(am4372.dtsi).
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Davinci MDIO is always used as slave device which services
read/write requests from MDIO/PHY core. It doesn't use IRQ also.
As result, It's possible to relax PM runtime constraints for Davinci
MDIO and enable it on demand, instead of powering it during probe
and powering off during removal.
Hence, implement PM runtime autosuspend for Davinci MDIO, but keep it
disabled by default, because Davinci MDIO is integrated in big set of
TI devices and not all of them expected to work corectly with RPM
autosuspend enabled:
- expected to work on SoCs where MDIO is part of TI CPSW
(cpsw.c DRA7/am57x, am437x, am335x, dm814x)
- not verified on Keystone 2 and other SoCs where MDIO is used with TI EMAC IP
(davinci_emac.c: dm6467-emac, am3517-emac, dm816-emac).
Davinci MDIO RPM autosuspend can be enabled through sysfs:
echo 100 > /sys/devices/../48484000.ethernet/48485000.mdio/power/autosuspend_delay_ms
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add PM runtime .runtime_suspend()/.runtime_resume() callbacks and
perform Davinci MDIO enabling/disabling from these callbacks. This
allows to reuse pm_runtime_force_suspend/resume() APIs during System
suspend and required for further implementation of PM runtime
autosuspend.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Davinci MDIO MDIO_CONTROL.CLKDIV can be calculated only once
during probe, hence split __davinci_mdio_reset() on
davinci_mdio_init_clk() and davinci_mdio_enable(). Initialize and
save CLKDIV in .probe(). Then just use saved value.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's not expected Davinci MDIO to be accessible after its suspend
callbacks have been called:
- all consumers of Davinci MDIO will stop/disconnect phys at Device
suspend stage;
- all phys are expected to be suspned already by PHY/MDIO core;
- MDIO locking is done by MDIO Bus code.
Hence, it's safe to drop "suspended" and "lock" fields from mdio_data.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PM runtime is disabled when Davinci MDIO .suspend_late() and
.resume_early() callbacks are called. As result, any PM runtime calls here will
be just a nop and can be removed.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do PM runtime initialization later in probe - this allows to simplify
error handling a bit.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CPSW might be suspended by RPM if all ethX interfaces are down,
but it still could be accesible through net_device_ops interfce. In
this case net_device_ops operations requiring registers access will
cause L3 errors and CPSW crash.
Hence, fix it by adding RPM get/put calls in net_device_ops callbacks
which need to access CPSW registers: .ndo_set_mac_address(),
.ndo_vlan_rx_add_vid(), .ndo_vlan_rx_kill_vid().
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CPSW might be suspended by RPM if all ethX interfaces are down,
but it still could be accesible through ethtool interfce. In this case
ethtool operations, requiring registers access, will cause L3 errors and
CPSW crash.
ethtool callbcaks which need to access CPSW registers now:
.set_coalesce(), .get_ethtool_stats(), .set_pauseparam(), .get_regs()
Hence, fix it by adding .begin()/.complete() ethtool callbacks, which
will be called before/after each ethtool operation runs, and do CPSW
RPM handling in these callbacks. That way CPSW will be active while
handling ethtool requests.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PM runtime is properly handled in cpsw_ndo_open/stop(), as result it
isn't required to duplicate these calls in .suspend()/.resume()
callbacks. Moreover, it might cause unnecessary RPM resume of CPSW
during System suspend in the case it's already suspended because
all ethX interfaces are down already, before System suspend started.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missed check of return code from PM runtime get() calls.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cpsw_suspend() could trigger L3 error and CPSW will stop
functioning if System enters suspend when all ethX net-devices are
down - in this case CPSW could be already suspended by PM runtime, but
cpsw_suspend() will try to call soft_reset_slave() unconditionally
and access CPSW registers.
Hence, fix it by moving soft_reset_slave() from cpsw_suspend() to
cpsw_slave_stop(). This way slave ports will be reset when CPSW is
active and will be in proper state during Suspend.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Giuseppe Cavallaro says:
====================
stmmac: rework and enhance the PCS support
The 3.xx and 4.xx synopsys gmacs have a very similar
PCS embedded module and they share almost the same registers;
for example:
AN_Control, AN_Status, AN_Advertisement, AN_Link_Partner_Ability,
AN_Expansion, TBI_Extended_Status.
Just the RGMII/SMII Control/Status register differs.
So these patches aim to reorganize and enhance the PCS support;
to do that, some small inline functions have been provided and
also some rework to the PCS ISR part has been done.
In the end, the SGMII for MAC2MAC connection has been introduced.
All patches have been built on top of net-next git and, as for
the previous version, not fully tested.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of SGMII more, for example when a MAC2MAC connection
is needed, the port selection bits (inside the MAC configuration
registers) have to be programmed according to the link selected.
So the patch adds a new DT parameter to pass the port selection
and to programmed related PCS and CORE to use it.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By default, all gmac cores disable the PCS block and always
enable the PMT.
Note that this is done in a different way by 3.x and 4.x cores.
With this rework, PCS and PMT interrupt masks can be driven by
parameters now moved inside the mac_device_info structure
and the settings follow what the HW capability register reports.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 3.xx and 4.xx synopsys gmacs have a very similar
PCS embedded module and they share almost the same registers:
for example:
AN_Control, AN_Status, AN_Advertisement, AN_Link_Partner_Ability,
AN_Expansion, TBI_Extended_Status.
Just the RGMII/SMII Control/Status register differs.
So This patch aims to reorganize and enhance the PCS support.
It removes the existent support from the dwmac1000/dwmac4_core.c
moving basic PCS functions inside a new file called: stmmac_pcs.h.
The patch also reviews the available APIs to be better shared among
different hardware and easily enhanced to support new features.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bridge is falsly dropping ipv6 mulitcast packets if there is:
1. No ipv6 address assigned on the brigde.
2. No external mld querier present.
3. The internal querier enabled.
When the bridge fails to build mld queries, because it has no
ipv6 address, it slilently returns, but keeps the local querier enabled.
This specific case causes confusing packet loss.
Ipv6 multicast snooping can only work if:
a) An external querier is present
OR
b) The bridge has an ipv6 address an is capable of sending own queries
Otherwise it has to forward/flood the ipv6 multicast traffic,
because snooping cannot work.
This patch fixes the issue by adding a flag to the bridge struct that
indicates that there is currently no ipv6 address assinged to the bridge
and returns a false state for the local querier in
__br_multicast_querier_exists().
Special thanks to Linus Lüssing.
Fixes: d1d81d4c3d ("bridge: check return value of ipv6_dev_get_saddr()")
Signed-off-by: Daniel Danzberger <daniel@dd-wrt.com>
Acked-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
The usage Confidence is mandary to Windows Precision Touchpad devices. If
it is examined in input_mapping on a WIndows Precision Touchpad, a new add
quirk MT_QUIRK_CONFIDENCE desgned for such devices will be applied to the
device. A touch with the confidence bit is not set is determined as
invalid.
Tested on Dell XPS13 9343
Cc: stable@vger.kernel.org # v4.5+
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Andy Lutomirski <luto@kernel.org> # XPS 13 9350, BIOS 1.4.3
Signed-off-by: Allen Hung <allen_hung@dell.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This reverts commit 25a84db15b ("HID: multitouch: enable palm rejection
if device implements confidence usage")
The commit enables palm rejection for Win8 Precision Touchpad devices but
the quirk MT_QUIRK_VALID_IS_CONFIDENCE it is using is not working very
properly. This quirk is originally designed for some WIn7 touchscreens. Use
of this for a Win8 Precision Touchpad will cause unexpected pointer jumping
problem.
Cc: stable@vger.kernel.org # v4.5+
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Andy Lutomirski <luto@kernel.org> # XPS 13 9350, BIOS 1.4.3
Signed-off-by: Allen Hung <allen_hung@dell.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
If a user space program (e.g., wpa_supplicant) deletes a STA entry that
is currently in NL80211_PLINK_ESTAB state, the number of established
plinks counter was not decremented and this could result in rejecting
new plink establishment before really hitting the real maximum plink
limit. For !user_mpm case, this decrementation is handled by
mesh_plink_deactive().
Fix this by decrementing estab_plinks on STA deletion
(mesh_sta_cleanup() gets called from there) so that the counter has a
correct value and the Beacon frame advertisement in Mesh Configuration
element shows the proper value for capability to accept additional
peers.
Cc: stable@vger.kernel.org
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Calling the fixed-phy functions when CONFIG_FIXED_PHY=m as a previous
change tried cannot work if the caller is in built-in code:
drivers/of/built-in.o: In function `of_phy_register_fixed_link':
of_reserved_mem.c:(.text+0x85e0): undefined reference to `fixed_phy_register'
Making of_mdio depend on 'FIXED_PHY || !FIXED_PHY' would solve this
dependency by enforcing that OF_MDIO itself becomes a loadable module
when FIXED_PHY=y, but that creates a different dependency as it
breaks any built-in ethernet driver that uses of_mdio.
Making FIXED_PHY a bool option also cannot work, since it depends on
PHYLIB, which again is tristate.
This version now uses 'select FIXED_PHY' to ensure that the fixed-phy
portion of of_mdio is not optional. The main downside of this is
a small increase in code size for cases that do not need fixed phy
support, but it should avoid all of the link-time problems.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: d1bd330a22 ("of_mdio: Enable fixed PHY support if driver is a module")
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
