This patch removes the unnecessary display of PCIe bandwidth twice. Since the
ixgbe_check_minimum_link does a better job, and ensures accurate detection on
even complex chains, this older check is no longer necessary.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch updates the ixgbe_check_minimum_link function to correctly show that
there is some minor loss of encoding, even though we don't calculate it in the
max GT/s equation. It is small enough to not bother, but is better to report it
than not.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ixgbe_napi_disable_all calls napi_disable on each queue, however the busy
polling code introduced a local_bh_disable()d context around the napi_disable.
The original author did not realize that napi_disable might sleep, which would
cause a sleep while atomic BUG. In addition, on a single processor system, the
ixgbe_qv_lock_napi loop shouldn't have to mdelay. This patch adds an
ixgbe_qv_disable along with a new IXGBE_QV_STATE_DISABLED bit, which it uses to
indicate to the poll and napi routines that the q_vector has been disabled. Now
the ixgbe_napi_disable_all function will wait until all pending work has been
finished and prevent any future work from being started.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Cc: Eliezer Tamir <eliezer.tamir@linux.intel.com>
Cc: Alexander Duyck <alexander.duyck@intel.com>
Cc: Hyong-Youb Kim <hykim@myri.com>
Cc: Amir Vadai <amirv@mellanox.com>
Cc: Dmitry Kravkov <dmitry@broadcom.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
napi_disable uses an msleep() call to wait for outstanding napi work to be
finished after setting the disable bit. It does not always sleep incase there
was no outstanding work. This resulted in a rare bug in ixgbe_down operation
where a napi_disable call took place inside of a local_bh_disable()d context.
In order to enable easier detection of future sleep while atomic BUGs, this
patch adds a might_sleep() call, so that every use of napi_disable during
atomic context will be visible.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Cc: Eliezer Tamir <eliezer.tamir@linux.intel.com>
Cc: Alexander Duyck <alexander.duyck@intel.com>
Cc: Hyong-Youb Kim <hykim@myri.com>
Cc: Amir Vadai <amirv@mellanox.com>
Cc: Dmitry Kravkov <dmitry@broadcom.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch removes the burden from the NIC drivers to check if the
vxlan driver is enabled in the kernel and also makes available
the vxlan headrooms to them.
Signed-off-by: Joseph Gasparakis <joseph.gasparakis@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
drivers/net/vxlan.c: In function ‘vxlan_sock_add’:
drivers/net/vxlan.c:2298:11: warning: ‘sock’ may be used uninitialized in this function [-Wmaybe-uninitialized]
drivers/net/vxlan.c:2275:17: note: ‘sock’ was declared here
LD drivers/net/built-in.o
Signed-off-by: Zhi Yong Wu <wuzhy@linux.vnet.ibm.com>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
UFO as well as UDP_CORK do not respect IP_PMTUDISC_DO and
IP_PMTUDISC_PROBE well enough.
UFO enabled packet delivery just appends all frags to the cork and hands
it over to the network card. So we just deliver non-DF udp fragments
(DF-flag may get overwritten by hardware or virtual UFO enabled
interface).
UDP_CORK does enqueue the data until the cork is disengaged. At this
point it sets the correct IP_DF and local_df flags and hands it over to
ip_fragment which in this case will generate an icmp error which gets
appended to the error socket queue. This is not reflected in the syscall
error (of course, if UFO is enabled this also won't happen).
Improve this by checking the pmtudisc flags before appending data to the
socket and if we still can fit all data in one packet when IP_PMTUDISC_DO
or IP_PMTUDISC_PROBE is set, only then proceed.
We use (mtu-fragheaderlen) to check for the maximum length because we
ensure not to generate a fragment and non-fragmented data does not need
to have its length aligned on 64 bit boundaries. Also the passed in
ip_options are already aligned correctly.
Maybe, we can relax some other checks around ip_fragment. This needs
more research.
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The virtio_net driver's mergeable receive buffer allocator
uses 4KB packet buffers. For MTU-sized traffic, SKB truesize
is > 4KB but only ~1500 bytes of the buffer is used to store
packet data, reducing the effective TCP window size
substantially. This patch addresses the performance concerns
with mergeable receive buffers by allocating MTU-sized packet
buffers using page frag allocators. If more than MAX_SKB_FRAGS
buffers are needed, the SKB frag_list is used.
Signed-off-by: Michael Dalton <mwdalton@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code for privacy extentions is very mature, and making it
configurable only gives marginal memory/code savings in exchange
for obfuscation and hard to read code via CPP ifdef'ery.
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Aring says:
====================
6lowpan: trivial changes
This patch series includes some trivial changes to prepare the 6lowpan stack
for upcomming patch-series which mainly fix fragmentation according to rfc4944
and udp handling(which is currently broken).
Changes since v3:
- really fix intendation in patch 3/5
Changes since v2:
- change intendation in patch 3/5
- fix typo in 5/5 unecessary -> unnecessary
- add missing 6lowpan tag in cover-letter
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reviewed-by: Werner Almesberger <werner@almesberger.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the assignment of skb->dev. We don't need it here because
we use the netdev_alloc_skb_ip_align function which already sets the
skb->dev.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reviewed-by: Werner Almesberger <werner@almesberger.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch uses the netdev_alloc_skb instead dev_alloc_skb function and
drops the seperate assignment to skb->dev.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reviewed-by: Werner Almesberger <werner@almesberger.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The err variable can only be zero in this case.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reviewed-by: Werner Almesberger <werner@almesberger.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reviewed-by: Werner Almesberger <werner@almesberger.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two if statements do the same work, we can merge them to
one. And fix some typos. There is just code simplification,
no functional changes.
Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
kmem_cache_zalloc had set the allocated memory to zero. I think no need
to initialize with 0. And move the comments to the function begin.
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fix some typos
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While investigating on a recent vxlan regression, I found veth
was using a zero features set for vxlan tunnels.
We have to segment GSO frames, copy the payload, and do the checksum.
This patch brings a ~200% performance increase
We probably have to add hw_enc_features support
on other virtual devices.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexei reported a performance regression on vxlan, caused
by commit 3347c96029 "ipv4: gso: make inet_gso_segment() stackable"
GSO vxlan packets were not properly segmented, adding IP fragments
while they were not expected.
Rename 'bool tunnel' to 'bool encap', and add a new boolean
to express the fact that UDP should be fragmented.
This fragmentation is triggered by skb->encapsulation being set.
Remove a "skb->encapsulation = 1" added in above commit,
as its not needed, as frags inherit skb->frag from original
GSO skb.
Reported-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Tested-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 4d961a101e, reversing
changes made to a00f6fcc7d.
Revert bond locking changes, they cause regressions and Veaceslav Falico
doesn't like how the commit messages were done at all.
Signed-off-by: David S. Miller <davem@davemloft.net>
Includes:
- ndo_busy_poll implementation
- Locking between napi and busy_poll
- Fix rx_post_starvation (replenish rx-queues in out-of-mememory scenario)
logic to accomodate busy_poll.
v2 changes:
[Eric D.'s comment] call alloc_pages() with GFP_ATOMIC even in ndo_busy_poll
context as it is not allowed to sleep.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ding Tianhong says:
====================
bonding: patchset for rcu use in bonding
The slave list will add and del by bond_master_upper_dev_link() and
bond_upper_dev_unlink(), which will call call_netdevice_notifiers(),
even it is safe to call it in write bond lock now, but we can't sure
that whether it is safe later, because other drivers may deal
NETDEV_CHANGEUPPER in sleep way, so I didn't admit move the
bond_upper_dev_unlink() in write bond lock.
now the bond_for_each_slave only protect by rtnl_lock(), maybe use
bond_for_each_slave_rcu is a good way to protect slave list for bond,
but as a system slow path, it is no need to transform
bond_for_each_slave() to bond_for_each_slave_rcu() in slow path, so in
the patchset, I will remove the unused read bond lock for monitor
function, maybe it is a better way, I will wait to accept any relay
for it.
Thanks for the Veaceslav Falico opinion.
v2: add and modify commit for patchset and patch, it will be the first
step for the whole patchset.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The bond slave list may change when the monitor is running, the slave list is no longer
protected by bond->lock, only protected by rtnl lock(), so we have 3 ways to modify it:
1.add bond_master_upper_dev_link() and bond_upper_dev_unlink() in bond->lock, but it is unsafe
to call call_netdevice_notifiers() in write lock.
2.remove unused bond->lock for monitor function, only use the existing rtnl lock().
3.use rcu_read_lock() to protect it, of course, it will transform bond_for_each_slave to
bond_for_each_slave_rcu() and performance is better, but in slow path, it is ignored.
so I remove the bond->lock and move the rtnl lock to protect the whole monitor function.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bond slave list may change when the monitor is running, the slave list is no longer
protected by bond->lock, only protected by rtnl lock(), so we have 3 ways to modify it:
1.add bond_master_upper_dev_link() and bond_upper_dev_unlink() in bond->lock, but it is unsafe
to call call_netdevice_notifiers() in write lock.
2.remove unused bond->lock for monitor function, only use the existing rtnl lock().
3.use rcu_read_lock() to protect it, of course, it will transform bond_for_each_slave to
bond_for_each_slave_rcu() and performance is better, but in slow path, it is ignored.
so I remove the bond->lock and move the rtnl lock to protect the whole monitor function.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bond slave list may change when the monitor is running, the slave list is no longer
protected by bond->lock, only protected by rtnl lock(), so we have 3 ways to modify it:
1.add bond_master_upper_dev_link() and bond_upper_dev_unlink() in bond->lock, but it is unsafe
to call call_netdevice_notifiers() in write lock.
2.remove unused bond->lock for monitor function, only use the existing rtnl lock().
3.use rcu_read_lock() to protect it, of course, it will transform bond_for_each_slave to
bond_for_each_slave_rcu() and performance is better, but in slow path, it is ignored.
so I remove the bond->lock and add the rtnl lock to protect the whole monitor function.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bond slave list may change when the monitor is running, the slave list is no longer
protected by bond->lock, only protected by rtnl lock(), so we have 3 ways to modify it:
1.add bond_master_upper_dev_link() and bond_upper_dev_unlink() in bond->lock, but it is unsafe
to call call_netdevice_notifiers() in write lock.
2.remove unused bond->lock for monitor function, only use the existing rtnl lock().
3.use rcu_read_lock() to protect it, of course, it will transform bond_for_each_slave to
bond_for_each_slave_rcu() and performance is better, but in slow path, it is ignored.
so I remove the bond->lock and move the rtnl lock to protect the whole monitor function.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bond slave list may change when the monitor is running, the slave list is no longer
protected by bond->lock, only protected by rtnl lock(), so we have 3 ways to modify it:
1.add bond_master_upper_dev_link() and bond_upper_dev_unlink() in bond->lock, but it is unsafe
to call call_netdevice_notifiers() in write lock.
2.remove unused bond->lock for monitor function, only use the existing rtnl lock().
3.use rcu_read_lock() to protect it, of course, it will transform bond_for_each_slave to
bond_for_each_slave_rcu() and performance is better, but in slow path, it is ignored.
so I remove the bond->lock and move the rtnl lock to protect the whole monitor function.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates
This series contains updates to igb, igbvf, i40e, ixgbe and ixgbevf.
Dan Carpenter provides a patch for igbvf to fix a bug found by a static
checker. If the new MTU is very large, then "new_mtu + ETH_HLEN +
ETH_FCS_LEN" can wrap and the check on the next line can underflow.
Wei Yongjun provides 2 patches, the first against igbvf adds a missing
iounmap() before the return from igbvf_probe(). The second against
i40e, removes the include <linux/version.h> because it is not needed.
Carolyn provides a patch for igb to fix a call to set the master/slave
mode for all m88 generation 2 PHY's and removes the call for I210
devices which do not need it.
Stefan Assmann provides a patch for igb to fix an issue which was broke
by:
commit fa44f2f185
Author: Greg Rose <gregory.v.rose@intel.com>
Date: Thu Jan 17 01:03:06 2013 -0800
igb: Enable SR-IOV configuration via PCI sysfs interface
which breaks the reloading of igb when VFs are assigned to a guest, in
several ways.
Jacob provides a patch for ixgbe and ixgbevf. First, against ixgbe,
cleans up ixgbe_enumerate_functions to reduce code complexity. The
second, against ixgbevf, adds support for ethtool's get_coalesce and
set_coalesce command for the ixgbevf driver.
Yijing Wang provides a patch for ixgbe to use pcie_capability_read_word()
to simplify the code.
Emil provides a ixgbe patch to fix an issue where the logic used to
detect changes in rx-usecs was incorrect and was masked by the call to
ixgbe_update_rsc().
Don provides 2 patches for ixgbevf. First creates a new function to set
PSRTYPE. The second bumps the ixgbevf driver version.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We also can defer the initialization of hashrnd in flow_dissector
to its first use. Since net_get_random_once is irq safe now we don't
have to audit the call paths if one of this functions get called by an
interrupt handler.
Cc: David S. Miller <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
I initial build non irq safe version of net_get_random_once because I
would liked to have the freedom to defer even the extraction process of
get_random_bytes until the nonblocking pool is fully seeded.
I don't think this is a good idea anymore and thus this patch makes
net_get_random_once irq safe. Now someone using net_get_random_once does
not need to care from where it is called.
Cc: David S. Miller <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
I think that a dev_put() is needed in the error path to preserve the
proper dev refcount.
CC: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Acked-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The transition from markov state "3 => lost packets within a burst
period" to "1 => successfully transmitted packets within a gap period"
has no *additional* loss event. The loss already happen for transition
from 1 -> 3, this additional loss will make things go wild.
E.g. transition probabilities:
p13: 10%
p31: 100%
Expected:
Ploss = p13 / (p13 + p31)
Ploss = ~9.09%
... but it isn't. Even worse: we get a double loss - each time.
So simple don't return true to indicate loss, rather break and return
false.
Signed-off-by: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Stefano Salsano <stefano.salsano@uniroma2.it>
Cc: Fabio Ludovici <fabio.ludovici@yahoo.it>
Signed-off-by: Hagen Paul Pfeifer <hagen@jauu.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bump patch to reflect what version of the out of tree driver it has
equivalent functionality with (2.11.3).
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for ethtool's get_coalesce and set_coalesce command for
the ixgbevf driver. This enables dynamically updating the minimum time between
interrupts.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch creates a new function to set PSRTYPE. This function helps lay
the ground work for eventual multi queue support.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch resolves an issue where the logic used to detect changes in rx-usecs
was incorrect and was masked by the call to ixgbe_update_rsc().
Setting rx-usecs between 0,2-9 and 1,10 and up requires a reset to allow
ixgbe_configure_tx_ring() to set the correct value for TXDCTL.WTHRESH in
order to avoid Tx hangs with BQL enabled.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
use pcie_capability_read_word() to simplify code.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This function previously had the same check as used by the
ixgbe_pcie_from_parent. As the hardcode is due to the device having an internal
switch, this function should simply use the call from ixgbe_pcie_from_parent.
This reduces code complexity and makes it less likely a developer will forget
to update the list in the future.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
commit fa44f2f185 broke reloading of igb, when
VFs are assigned to a guest, in several ways.
1. on module load adapter->vf_data does not get properly allocated,
resulting in a null pointer exception when accessing adapter->vf_data in
igb_reset() on module reload.
modprobe -r igb ; modprobe igb max_vfs=7
[ 215.215837] igb 0000:01:00.1: removed PHC on eth1
[ 216.932072] igb 0000:01:00.1: IOV Disabled
[ 216.937038] igb 0000:01:00.0: removed PHC on eth0
[ 217.127032] igb 0000:01:00.0: Cannot deallocate SR-IOV virtual functions while they are assigned - VFs will not be deallocated
[ 217.146178] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.0.5-k
[ 217.154050] igb: Copyright (c) 2007-2013 Intel Corporation.
[ 217.160688] igb 0000:01:00.0: Enabling SR-IOV VFs using the module parameter is deprecated - please use the pci sysfs interface.
[ 217.173703] igb 0000:01:00.0: irq 103 for MSI/MSI-X
[ 217.179227] igb 0000:01:00.0: irq 104 for MSI/MSI-X
[ 217.184735] igb 0000:01:00.0: irq 105 for MSI/MSI-X
[ 217.220082] BUG: unable to handle kernel NULL pointer dereference at 0000000000000048
[ 217.228846] IP: [<ffffffffa007c5e5>] igb_reset+0xc5/0x4b0 [igb]
[ 217.235472] PGD 3607ec067 PUD 36170b067 PMD 0
[ 217.240461] Oops: 0002 [#1] SMP
[ 217.244085] Modules linked in: igb(+) igbvf mptsas mptscsih mptbase scsi_transport_sas [last unloaded: igb]
[ 217.255040] CPU: 4 PID: 4833 Comm: modprobe Not tainted 3.11.0+ #46
[...]
[ 217.390007] [<ffffffffa007fab2>] igb_probe+0x892/0xfd0 [igb]
[ 217.396422] [<ffffffff81470b3e>] local_pci_probe+0x1e/0x40
[ 217.402641] [<ffffffff81472029>] pci_device_probe+0xf9/0x110
[...]
2. A follow up issue, pci_enable_sriov() should only be called if no VFs were
still allocated on module unload. Otherwise pci_enable_sriov() gets called
multiple times in a row rendering the NIC unusable until reset.
3. simply calling igb_enable_sriov() in igb_probe_vfs() is not enough as the
interrupts need to be re-setup. Switching that to igb_pci_enable_sriov().
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Tested-by: Sibai Li <Sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch calls code to set the master/slave mode for all m88 gen 2
PHY's. This patch also removes the call to this function for I210 devices
only from the function that is not called by I210 devices.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@gmail.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove including <linux/version.h> that don't need it.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add the missing iounmap() before return from igbvf_probe()
in the error handling case.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Tested-by: Sibai Li <Sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If new_mtu is very large then "new_mtu + ETH_HLEN + ETH_FCS_LEN" can
wrap and the check on the next line can underflow. This is one of those
bugs which can be triggered by the user if you have namespaces
configured.
Also since this is something the user can trigger then we don't want to
have dev_err() message.
This is a static checker fix and I'm not sure what the impact is.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Tested-by: Sibai Li Sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
- data structure reshaping to accommodate multiple routing protocol
implementations
- routing protocol API enhancement
- send to userspace the event "batman-adv Gateway loss" in case of soft-iface
destruction and a "batman-adv Gateway" was configured
- improve the TT component to support and advertise runtime flag changes
- minor code refactoring
- make the ICMP kernel-to-userspace communication more generic
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=sYKR
-----END PGP SIGNATURE-----
Merge tag 'batman-adv-for-davem' of git://git.open-mesh.org/linux-merge
Antonio Quartulli says:
====================
this is another set of changes intended for net-next/linux-3.13.
(probably our last pull request for this cycle)
Patches 1 and 2 reshape two of our main data structures in a way that they can
easily be extended in the future to accommodate new routing protocols.
Patches from 3 to 9 improve our routing protocol API and its users so that all
the protocol-related code is not mixed up with the other components anymore.
Patch 10 limits the local Translation Table maximum size to a value such that it
can be fully transfered over the air if needed. This value depends on
fragmentation being enabled or not and on the mtu values.
Patch 11 makes batman-adv send a uevent in case of soft-interface destruction
while a "bat-Gateway" was configured (this informs userspace about the GW not
being available anymore).
Patches 13 and 14 enable the TT component to detect non-mesh client flag
changes at runtime (till now those flags where set upon client detection and
were not changed anymore).
Patch 16 is a generalisation of our user-to-kernel space communication (and
viceversa) used to exchange ICMP packets to send/received to/from the mesh
network. Now it can easily accommodate new ICMP packet types without breaking
the existing userspace API anymore.
Remaining patches are minor changes and cleanups.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Hannes Frederic Sowa says:
====================
initialize fragment hash secrets with net_get_random_once
This series switches the inet_frag.rnd hash initialization to
net_get_random_once.
Included patches:
ipv4: initialize ip4_frags hash secret as late
ipv6: split inet6_hash_frag for netfilter and
inet: remove old fragmentation hash initializing
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
