- Support for SiFive FU740 PRCI
- Add hardware enable information to clk_summary debugfs
* clk-tegra:
clk: tegra: Fix duplicated SE clock entry
clk: tegra: bpmp: Clamp clock rates on requests
clk: tegra: Do not return 0 on failure
* clk-imx: (24 commits)
clk: imx: scu: remove the calling of device_is_bound
clk: imx: scu: Make pd_np with static keyword
clk: imx8mq: drop of_match_ptr from of_device_id table
clk: imx8mp: drop of_match_ptr from of_device_id table
clk: imx8mn: drop of_match_ptr from of_device_id table
clk: imx8mm: drop of_match_ptr from of_device_id table
clk: imx: gate2: Remove unused variable ret
clk: imx: gate2: Add locking in is_enabled op
clk: imx: gate2: Add cgr_mask for more flexible number of control bits
clk: imx: gate2: Check if clock is enabled against cgr_val
clk: imx: gate2: Keep the register writing in on place
clk: imx: gate2: Remove the IMX_CLK_GATE2_SINGLE_BIT special case
clk: imx: scu: fix build break when compiled as modules
clk: imx: remove redundant assignment to pointer np
clk: imx: remove unneeded semicolon
clk: imx: lpcg: add suspend/resume support
clk: imx: clk-imx8qxp-lpcg: add runtime pm support
clk: imx: lpcg: allow lpcg clk to take device pointer
clk: imx: imx8qxp-lpcg: add parsing clocks from device tree
clk: imx: scu: add suspend/resume support
...
* clk-sifive:
clk: sifive: Add clock enable and disable ops
clk: sifive: Fix the wrong bit field shift
clk: sifive: Add a driver for the SiFive FU740 PRCI IP block
clk: sifive: Use common name for prci configuration
clk: sifive: Extract prci core to common base
dt-bindings: fu740: prci: add YAML documentation for the FU740 PRCI
* clk-mediatek:
clk: mediatek: Make mtk_clk_register_mux() a static function
* clk-summary:
clk: Add hardware-enable column to clk summary
Add "hardware enable" column to the clk summary in order to show actual
hardware enable-state of all clocks. The possible states are "Y/N/?",
where question mark means that state is unknown, i.e. clock isn't a
mux and clk-driver doesn't support is_enabled() callback for this clock.
In conjunction with clk_ignore_unused, this tells us what unused clocks
are left enabled after bootloader. This is also a useful aid for
debugging interactions with firmware which changes clock states without
notifying kernel.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20201115203432.13934-1-digetx@gmail.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add new functions "sifive_prci_clock_enable(), sifive_prci_clock_disable()
and sifive_clk_is_enabled()" to enable or disable the PRCI clock
Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Tested-by: Zong Li <zong.li@sifive.com>
Link: https://lore.kernel.org/r/20201209094916.17383-6-zong.li@sifive.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add driver code for the SiFive FU740 PRCI IP block. This IP block
handles reset and clock control for the SiFive FU740 device and
implements SoC-level clock tree controls and dividers.
The link of unmatched as follow, and the U740-C000 manual would
be present in the same page as soon.
https://www.sifive.com/boards/hifive-unmatched
This driver contains bug fixes and contributions from
Henry Styles <hes@sifive.com>
Erik Danie <erik.danie@sifive.com>
Pragnesh Patel <pragnesh.patel@sifive.com>
Signed-off-by: Zong Li <zong.li@sifive.com>
Reviewed-by: Pragnesh Patel <Pragnesh.patel@sifive.com>
Acked-by: Palmer Dabbelt <palmerdabbelt@google.com>
Cc: Henry Styles <hes@sifive.com>
Cc: Erik Danie <erik.danie@sifive.com>
Cc: Pragnesh Patel <pragnesh.patel@sifive.com>
Link: https://lore.kernel.org/r/20201209094916.17383-4-zong.li@sifive.com
[sboyd@kernel.org: Include header to silence sparse]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Use generic name CLK_SIFIVE_PRCI instead of CLK_SIFIVE_FU540_PRCI. This
patch is prepared for fu740 support.
Signed-off-by: Zong Li <zong.li@sifive.com>
Reviewed-by: Palmer Dabbelt <palmerdabbelt@google.com>
Acked-by: Palmer Dabbelt <palmerdabbelt@google.com>
Reviewed-by: Pragnesh Patel <Pragnesh.patel@sifive.com>
Link: https://lore.kernel.org/r/20201209094916.17383-3-zong.li@sifive.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Extract common core of prci driver to an independent file, it could
allow other chips to reuse it. Separate SoCs-dependent code 'fu540'
from prci core, then we can easily add 'fu740' later.
Almost these changes are code movement. The different is adding the
private data for each SoC use, so it needs to get match data in probe
callback function, then use the data for initialization.
Signed-off-by: Zong Li <zong.li@sifive.com>
Reviewed-by: Pragnesh Patel <Pragnesh.patel@sifive.com>
Acked-by: Palmer Dabbelt <palmerdabbelt@google.com>
Link: https://lore.kernel.org/r/20201209094916.17383-2-zong.li@sifive.com
[sboyd@kernel.org: Include header to silence sparse]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
- A series from Abel Vesa to improve clk-gate2 driver and make it more
flexible.
- A patch set from Dong Aisheng to add a new two cells binding for SCU
clocks, so that IMX SCU based platforms like MX8QM and MX8QXP can be
supported with SS (Subsystems).
- Drop of_match_ptr from of_device_id table for i.MX8 clock drivers, as
they can only be probed from device tree.
- Other small cosmetic changes.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCgAyFiEEFmJXigPl4LoGSz08UFdYWoewfM4FAl/GDiEUHHNoYXduZ3Vv
QGtlcm5lbC5vcmcACgkQUFdYWoewfM4KaQf+LZOSdtzmWzjtvum3coOE+THVWYXz
hueT2RQjR8pCdBc6IIQi+2vPak5cvy+fazDl0NAXWr/OryEBw4fNPbDzYkky2gdY
HTslQYHrj8dufUN4tZ2yhofE0fqjgGkdcVczIzdbrodoj+cHjLKXc9GlwFy2hbi8
U9sUWYisrSFXCO+vQrheJrEcnUpnawfbKrl24Rpg0b1RVHC1s0rIYix3IyMeGm0P
q7h+rPtIMmaX86hfuSLxo2GdoGcsLNzRVSglz1Csndt/lfhWCfniAvsTNHnKWRDH
paEPMRUMwLSgOfPc4tpR8v0GjWRjOPmAk53lkncvW3ysa+o5ScIXycE1WQ==
=TiqG
-----END PGP SIGNATURE-----
Merge tag 'clk-imx-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into clk-imx
Pull i.MX clk driver updates from Shawn Guo:
- A series from Abel Vesa to improve clk-gate2 driver and make it more
flexible.
- A patch set from Dong Aisheng to add a new two cells binding for SCU
clocks, so that IMX SCU based platforms like MX8QM and MX8QXP can be
supported with SS (Subsystems).
- Drop of_match_ptr from of_device_id table for i.MX8 clock drivers, as
they can only be probed from device tree.
- Other small cosmetic changes.
* tag 'clk-imx-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (24 commits)
clk: imx: scu: remove the calling of device_is_bound
clk: imx: scu: Make pd_np with static keyword
clk: imx8mq: drop of_match_ptr from of_device_id table
clk: imx8mp: drop of_match_ptr from of_device_id table
clk: imx8mn: drop of_match_ptr from of_device_id table
clk: imx8mm: drop of_match_ptr from of_device_id table
clk: imx: gate2: Remove unused variable ret
clk: imx: gate2: Add locking in is_enabled op
clk: imx: gate2: Add cgr_mask for more flexible number of control bits
clk: imx: gate2: Check if clock is enabled against cgr_val
clk: imx: gate2: Keep the register writing in on place
clk: imx: gate2: Remove the IMX_CLK_GATE2_SINGLE_BIT special case
clk: imx: scu: fix build break when compiled as modules
clk: imx: remove redundant assignment to pointer np
clk: imx: remove unneeded semicolon
clk: imx: lpcg: add suspend/resume support
clk: imx: clk-imx8qxp-lpcg: add runtime pm support
clk: imx: lpcg: allow lpcg clk to take device pointer
clk: imx: imx8qxp-lpcg: add parsing clocks from device tree
clk: imx: scu: add suspend/resume support
...
The periph_clks[] array contains duplicated entry for Security Engine
clock which was meant to be defined for T210, but it wasn't added
properly. This patch corrects the T210 SE entry and fixes the following
error message on T114/T124: "Tegra clk 127: register failed with -17".
Fixes: dc37fec483 ("clk: tegra: periph: Add new periph clks and muxes for Tegra210")
Tested-by Nicolas Chauvet <kwizart@gmail.com>
Reported-by Nicolas Chauvet <kwizart@gmail.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20201025224212.7790-1-digetx@gmail.com
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This adds the RPMH clocks present in SM8350 SoC
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20201208064702.3654324-3-vkoul@kernel.org
[sboyd@kernel.org: Move sdx55 to the right place]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
50 MHz is an incredibly common clock rate for SD cards to run at.
It's "high speed" mode in SD (not very fast these days, but it used to
be) or:
#define HIGH_SPEED_MAX_DTR 50000000
If we don't support this then older "high speed" cards can only run at
25 MHz or at half their normal speed. There doesn't seem to be any
reason to skip this clock rate, so add it.
Fixes: 17269568f7 ("clk: qcom: Add Global Clock controller (GCC) driver for SC7180")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20201210102234.2.I26dcc0cee374f5571d9929c9985f463773167e68@changeid
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
I would repeat the same commit message that was in commit 5e4b7e82d4
("clk: qcom: gcc-sdm845: Use floor ops for sdcc clks") but it seems
silly to do so when you could just go read that commit.
NOTE: this is actually extra terrible because we're missing the 50 MHz
rate in the table (see the next patch AKA ("clk: qcom: gcc-sc7180: Add
50 MHz clock rate for SDC2")). That means then when you run an older
SD card it'll try to clock it at 100 MHz when it's only specced to run
at 50 MHz max. As you can probably guess that doesn't work super
well.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Fixes: 17269568f7 ("clk: qcom: Add Global Clock controller (GCC) driver for SC7180")
Link: https://lore.kernel.org/r/20201210102234.1.I096779f219625148900fc984dd0084ed1ba87c7f@changeid
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The scpi_clk_match (struct of_device_id) is referenced only with
CONFIG_OF builds thus mark it as __maybe_unused:
drivers/clk/clk-scpi.c:132:34: warning:
‘scpi_clk_match’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201103162435.13689-8-krzk@kernel.org
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it might be not relevant here). This
fixes compile warning (!CONFIG_OF && !CONFIG_MODULES):
drivers/clk/clk-pwm.c:139:34: warning:
‘clk_pwm_dt_ids’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201103162435.13689-1-krzk@kernel.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
There is no reason to keep on using the __raw_{read,write}l() I/O
accessors in Renesas ARM driver code. Switch to using the plain
{read,write}l() I/O accessors, to have a chance that this works on
big-endian.
Suggested-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20201119125053.4065746-1-geert+renesas@glider.be
Describe the RPCSRC internal clock and the RPC[D2] clocks derived from it,
as well as the RPC-IF module clock, in the RZ/G2E (R8A774C0) CPG/MSSR
driver.
Add new clk type CLK_TYPE_GEN3_E3_RPCSRC to register rpcsrc as a fixed
clock on R-Car Gen3 E3 (and also RZ/G2E which is identical to E3 SoC),
parent and the divider is set based on the register value CPG_RPCCKCR[4:3]
which has been set prior to booting the kernel.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20201116101002.5986-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The R-Car V3U clock driver defines the R and OSC clocks using R-Car Gen3
clock types. However, The R-Car V3U clock driver does not use the R-Car
Gen3 clock driver core, hence registering the R and OSC clocks fails:
renesas-cpg-mssr e6150000.clock-controller: Failed to register core clock osc: -22
renesas-cpg-mssr e6150000.clock-controller: Failed to register core clock r: -22
Fix this by introducing clock definition macros specific to R-Car V3U.
Note that rcar_r8a779a0_cpg_clk_register() already handled the related
clock types. Drop the now unneeded include of rcar-gen3-cpg.h.
Fixes: 17bcc8035d ("clk: renesas: cpg-mssr: Add support for R-Car V3U")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20201109152614.2465483-1-geert+renesas@glider.be
Describe the RPCSRC internal clock and the RPC[D2] clocks derived from it,
as well as the RPC-IF module clock, in the RZ/G2N (R8A774B1) CPG/MSSR
driver.
Inspired by commit 94e3935b57 ("clk: renesas: r8a77980: Add RPC clocks").
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20201016121709.8447-4-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Describe the RPCSRC internal clock and the RPC[D2] clocks derived from it,
as well as the RPC-IF module clock, in the RZ/G2M (R8A774A1) CPG/MSSR
driver.
Inspired by commit 94e3935b57 ("clk: renesas: r8a77980: Add RPC clocks").
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20201016121709.8447-3-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
When compiling with clang:
drivers/clk/renesas/r8a779a0-cpg-mssr.c:156:21: warning: no previous prototype for function 'rcar_r8a779a0_cpg_clk_register' [-Wmissing-prototypes]
struct clk * __init rcar_r8a779a0_cpg_clk_register(struct device *dev,
^
drivers/clk/renesas/r8a779a0-cpg-mssr.c:156:1: note: declare 'static' if the function is not intended to be used outside of this translation unit
struct clk * __init rcar_r8a779a0_cpg_clk_register(struct device *dev,
^
static
Similarly, with sparse:
drivers/clk/renesas/r8a779a0-cpg-mssr.c:156:12: warning: symbol 'rcar_r8a779a0_cpg_clk_register' was not declared. Should it be static?
There are no users of rcar_r8a779a0_cpg_clk_register() outside this
file, so it should be static.
Fixes: 17bcc8035d ("clk: renesas: cpg-mssr: Add support for R-Car V3U")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20200924111808.15358-1-geert+renesas@glider.be
Add device tree bindings for global clock controller on SDX55 SoCs.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20201126072844.35370-2-manivannan.sadhasivam@linaro.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add support for the FlexSPI clock on Freescale Layerscape SoCs. The
clock is a simple divider based one and is located inside the device
configuration space (DCFG).
This will allow switching the SCK frequencies for the FlexSPI interface
on the LS1028A and the LX2160A.
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20201108185113.31377-8-michael@walle.cc
[sboyd@kernel.org: Drop modalias, add module table]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
To avoid future mistakes in the device tree for the clockgen module, add
constants for the clockgen subtype as well as a macro for the PLL
divider.
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20201108185113.31377-4-michael@walle.cc
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The Freescale QorIQ clock controller is only present on Freescale E500MC
and Layerscape SoCs. Add platform dependencies to the CLK_QORIQ config
symbol, to avoid asking the user about it when configuring a kernel
without E500MC or Layerscape support.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Li Yang <leoyang.li@nxp.com>
Link: https://lore.kernel.org/r/20201110154750.3285411-1-geert+renesas@glider.be
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The Xtensa time code is not a clock provider, and just needs to call
of_clk_init().
Hence it can include <linux/of_clk.h> instead of <linux/clk-provider.h>.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Link: https://lore.kernel.org/r/20201110155117.3286247-1-geert+renesas@glider.be
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The SuperH/J2 DT platform code is not a clock provider, and just needs
to call of_clk_init().
Hence it can include <linux/of_clk.h> instead of <linux/clk-provider.h>.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20201110155029.3286090-1-geert+renesas@glider.be
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
a unneeded redundancy removed and making i2s actually work on the
rk3066.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAl/NG9oQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgQ8WB/9MqzR0qPW3SYUF/ZbmB1hhHlQbaTiqimA0
UIynJoZ7Fl5b1yLH09ytAeLTk5prdqcZxLtXyWutjylHo/pGbYLVrpKqXuGJdNRu
uU6oDflIeQMF9IhOS2J2eFU7XHyvJJ87zECz13D0FoyDD88rTQpcMhFuL3HdkrA7
l5Fv6hX9PAWVZcforPiPNYVA4cH1nFrgshOK62Py1bPTJWkcXZqlflmfVLt3ikm6
uCjM03TJgADcoOyJkaZLJw6Rxvi6LWYDOHl5GHeo3iatEhWCju+v/xfnt41Aw6Zm
ld+Rw8B5dwfPguT78n2Wxvc5gFx2pItwReshZ9UPxggxsLdKWiPD
=M2Ua
-----END PGP SIGNATURE-----
Merge tag 'v5.11-rockchip-clk-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into clk-rockchip
Pull Rockchip clk driver updates from Heiko Stuebner:
Added arch-dependencies for the newly added per-soc config symbols,
an unneeded redundancy removed and making i2s actually work on the
rk3066.
* tag 'v5.11-rockchip-clk-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
clk: rockchip: fix i2s gate bits on rk3066 and rk3188
clk: rockchip: add CLK_SET_RATE_PARENT to sclk for rk3066a i2s and uart clocks
clk: rockchip: Remove redundant null check before clk_prepare_enable
clk: rockchip: Add appropriate arch dependencies
