To quote from section 1.3.1 of the data sheet:
The SGTL5000 has an internal reset that is deasserted
8 SYS_MCLK cycles after all power rails have been brought
up. After this time, communication can start
...
1.0us represents 8 SYS_MCLK cycles at the minimum 8.0 MHz SYS_MCLK.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Instead of calling device_create_file() manually, assign the static
attribute group entries at the device registration. This simplifies
the error handling and avoids the possible races.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
As DMA framework request DMA using direction only in prep_slave
function, (The At91 xdma driver has adapted to this request).
So won't check direction when do DMA configuration.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In startup function, enable ssc clock and in shutdown function,
disable clock. And also remove disable ssc in shutdown function,
as ssc is disabled in prepare function.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When SCC work in DSP A mode, the data outputs/inputs are shift out on
falling edge, the frame sync are sample on the rising edge.
Reported-by: Songjun Wu <songjun.wu@atmel.com>
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Shift the I2S mode value by the necessary amount before writing the
registers. This makes Right Justified and PCM mode work in addition to
the default Left Justified mode.
Signed-off-by: Filip Brozovic <fbrozovic@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix the issue introduced by:
3684940933 ASoC: tlv320aic3x: Add TDM support
The CTRLC register were not receiving the correct delay configuration,
which will corrupt DSP_A audio mode.
Fixes: 3684940933 (ASoC: tlv320aic3x: Add TDM support)
Reported-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
This was overlooked in the late change to remove the I2S padding bits
from S24_LE mode. The patch also limits S32_LE mode to 384kHz, the
maximum according to the datasheets.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Mark Brown <broonie@kernel.org>
The PLL introduces jitter, which in turn introduces noice if used
to clock the DAC. Thus, avoid the PLL output, and use the PLL input
to drive the DAC clock, if possible.
This is described for the PCM5142/PCM5242 chips in the answers to the
forum post "PCM5142/PCM5242 DAC clock source" at the TI E2E community
pages (1).
(1) http://e2e.ti.com/support/data_converters/audio_converters/f/64/t/389994
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Mark Brown <broonie@kernel.org>
Using the PLL in master mode requires using an external connection
between one of the GPIO pins (configured as PLL/4 output) and the
SCK pin. It also requires the external clock to be fed to some other
GPIO pin instead of the SCK pin.
This is described for the PCM5122 chip in the answers to the forum post
"PCM5122 DAC as I2S master troubles with PLL mode" at the TI E2E
community pages (1). The clocking functionality is also much better
described in the datasheet for the chip PCM5242, which seems to be
register compatible with PCM512x and PCM514x (which both have severely
lacking datasheets).
(1) http://e2e.ti.com/support/data_converters/audio_converters/f/64/t/267830
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use register field names from the seemingly compatible PCM5242 datasheet,
as the PCM512x and PCM514x datasheets are severly lacking.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Mark Brown <broonie@kernel.org>
We need hold lock each time updating shirm registers, otherwise,
we may set unexpected values to them when they are set in
different thread at different time sequence.
The notification work will be scheduled in global work queue,
which won't hold this sst->spinlock itself, so here we need
change to use the lock version to update shim registers.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The I2C init path forgot to init the mutex, leading to an oops when
controls are accessed.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
As the clock can be get from TK/RK pin, so remove the comments.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
According to the I2S specification information as following:
- WS = 0, channel 1 (left)
- WS = 1, channel 2 (right)
So, the start event should be TF/RF falling edge.
Reported-by: Songjun Wu <songjun.wu@atmel.com>
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Save a bit of scheduling by coalescing all the output power up delays
into a single delay.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Give the output disable sequence a chance to fully complete, otherwise
there is a danger we may remove the clock before it is finished
resulting in a pop noise. The delay for each output must be cumulative
and these are coalesced into a single delay.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The IDE bit in the CONFF register is the third bit not the fourth.
Signed-off-by: Thomas Niederprüm <niederp@physik.uni-kl.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Asus T100TAF uses ACPI ID "10EC5642" for its audio codec. I suppose it is
updated ACPI ID for the RT5642 codec since some earlier platforms are using
"10EC5640" with the RT5642 too.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The purpose of rt286_adc_event is to mute/numnte the ADC mixer.
However, it will also set the capture volume to default value.
As a result, "ADC0 Capture Volume" is not working if it is set
before capture start. This patch remove rt286_adc_event and add
"ADC0 Capture Switch" to mute/unmute ADC mixer.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The wm97xx touchscreen driver binds itself to the snd_ac97 device that gets
registered by the CODEC driver and expects that the device has already been
reset. Before commit 6794f709b7 ("ASoC: ac97: Drop delayed device
registration") the device was only registered after the probe function of
the CODEC driver had finished running, but starting with the mentioned
commit the device is registered as soon as snd_soc_new_ac97_codec() is
called. This causes the touchscreen driver to no longer work. Modify the
CODEC drivers to use snd_soc_alloc_ac97_codec() instead of
snd_soc_new_ac97_codec() and make sure that the AC'97 device is reset before
the snd_ac97 device gets registered.
Fixes: 6794f709b7 ("ASoC: ac97: Drop delayed device registration")
Reported-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Manuel Lauss <manuel.lauss@gmail.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
In some cases it is necessary to before additional operations after the
device has been initialized and before the device is registered. This can
for example be resetting the device.
This patch introduces a new function snd_soc_alloc_ac97_codec() which is
similar to snd_soc_new_ac97_codec() except that it does not register the
device. Any users of snd_soc_alloc_ac97_codec() are responsible for calling
device_add() manually.
Fixes: 6794f709b7 ("ASoC: ac97: Drop delayed device registration")
Reported-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
We should select FSR also to be driven by McBSP, not only FSX.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
In soc_new_compress() when rtd->dai_link->dynamic is set, we create the pcm
substreams with this call:
ret = snd_pcm_new_internal(rtd->card->snd_card, new_name, num,
1, 0, &be_pcm);
which passes 0 as capture_count leading to
be_pcm->streams[SNDRV_PCM_STREAM_CAPTURE].substream
being NULL, hence when trying to set rtd a few lines below we get an oops.
Fix by using rtd->dai_link->dpcm_playback and rtd->dai_link->dpcm_capture as
playback_count and capture_count to snd_pcm_new_internal().
Signed-off-by: Qais Yousef <qais.yousef@imgtec.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
There are no more users of this field left so it can finally be removed.
New users should use snd_soc_dapm_to_codec(w->dapm);
The reason why it is removed is because it doesn't fit to well anymore in
the componentized ASoC hierarchy, where DAPM works on the snd_soc_component
level. And the alternative of snd_soc_dapm_to_codec(w->dapm) typically
generates the same amount of code, so there is really no reason to keep it.
For automatic conversion the following coccinelle semantic patch can be used:
// <smpl>
@@
struct snd_soc_dapm_widget *w;
@@
-w->codec
+snd_soc_dapm_to_codec(w->dapm)
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
