Unfortunately, struct iwreq isn't a proper subset of struct ifreq,
but is still handled by the same code path. Robert reported that
then applications may (randomly) fault if the struct iwreq they
pass happens to land within 8 bytes of the end of a mapping (the
struct is only 32 bytes, vs. struct ifreq's 40 bytes).
To fix this, pull out the code handling wireless extension ioctls
and copy only the smaller structure in this case.
This bug goes back a long time, I tracked that it was introduced
into mainline in 2.1.15, over 20 years ago!
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=195869
Reported-by: Robert O'Callahan <robert@ocallahan.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To make it clear that we never use struct ifreq, cast from it
directly in the wext entrypoint and use struct iwreq from there
on. The next patch will remove the cast again and pass the
correct struct from the beginning.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are no longer any drivers (in the tree proper, I didn't
check all the staging drivers) that take WEXT ioctls through
this API, the only remaining ones that even have ndo_do_ioctl
are using it only for private ioctls.
Therefore, we can remove this call.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* Avi fixes some fallout from my mac80211 RX flags changes
* Emmanuel fixes an issue with adhering to the spec, and
an oversight in the SMPS management code
* Jason's patch makes mac80211 use constant-time memory
comparisons for message authentication, to avoid having
potentially observable timing differences
* my fix makes mac80211 set the basic rates bitmap before
the channel so the next update to the driver has more
consistent data - this required another rework patch to
remove some useless 5/10 MHz code that can never be hit
-----BEGIN PGP SIGNATURE-----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=S5/1
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2017-06-13' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Some fixes:
* Avi fixes some fallout from my mac80211 RX flags changes
* Emmanuel fixes an issue with adhering to the spec, and
an oversight in the SMPS management code
* Jason's patch makes mac80211 use constant-time memory
comparisons for message authentication, to avoid having
potentially observable timing differences
* my fix makes mac80211 set the basic rates bitmap before
the channel so the next update to the driver has more
consistent data - this required another rework patch to
remove some useless 5/10 MHz code that can never be hit
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently when dumping a context data only word number '1' is read for the
entire context.
Fixes: c965db4446 ("qed: Add support for debug data collection")
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A new Sierra Wireless EM7305 device ID used in a Toshiba laptop,
and two Longcheer device IDs entries used by Telewell TW-3G HSPA+
branded modems.
Reported-by: Petr Kloc <petr_kloc@yahoo.com>
Reported-by: Teemu Likonen <tlikonen@iki.fi>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 90eff9096c ("net: phy: Allow splitting MDIO
bus/device support from PHYs") we could create a configuration where
MDIO_DEVICE=y and PHYLIB=m which leads to the following undefined
references:
drivers/built-in.o: In function `thunder_mdiobus_pci_remove':
>> mdio-thunder.c:(.text+0x2a212f): undefined reference to
>> `mdiobus_unregister'
>> mdio-thunder.c:(.text+0x2a2138): undefined reference to
>> `mdiobus_free'
drivers/built-in.o: In function `thunder_mdiobus_pci_probe':
mdio-thunder.c:(.text+0x2a22e7): undefined reference to
`devm_mdiobus_alloc_size'
mdio-thunder.c:(.text+0x2a236f): undefined reference to
`of_mdiobus_register'
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Fixes: 90eff9096c ("net: phy: Allow splitting MDIO bus/device support from PHYs")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's already added by pr_fmt so remove the explicit use.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrey reported a use-after-free in add_grec():
for (psf = *psf_list; psf; psf = psf_next) {
...
psf_next = psf->sf_next;
where the struct ip_sf_list's were already freed by:
kfree+0xe8/0x2b0 mm/slub.c:3882
ip_mc_clear_src+0x69/0x1c0 net/ipv4/igmp.c:2078
ip_mc_dec_group+0x19a/0x470 net/ipv4/igmp.c:1618
ip_mc_drop_socket+0x145/0x230 net/ipv4/igmp.c:2609
inet_release+0x4e/0x1c0 net/ipv4/af_inet.c:411
sock_release+0x8d/0x1e0 net/socket.c:597
sock_close+0x16/0x20 net/socket.c:1072
This happens because we don't hold pmc->lock in ip_mc_clear_src()
and a parallel mr_ifc_timer timer could jump in and access them.
The RCU lock is there but it is merely for pmc itself, this
spinlock could actually ensure we don't access them in parallel.
Thanks to Eric and Long for discussion on this bug.
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Getting the device version out of the driver really aids debugging.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes uninitialized symbol warning that
got introduced by the following commit
773fc8f6e8 ("net: rps: send out pending IPI's on CPU hotplug")
Signed-off-by: Ashwanth Goli <ashwanth@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
mac80211 allows to modify the SMPS state of an AP both,
when it is started, and after it has been started. Such a
change will trigger an action frame to all the peers that
are currently connected, and will be remembered so that
new peers will get notified as soon as they connect (since
the SMPS setting in the beacon may not be the right one).
This means that we need to remember the SMPS state
currently requested as well as the SMPS state that was
configured initially (and advertised in the beacon).
The former is bss->req_smps and the latter is
sdata->smps_mode.
Initially, the AP interface could only be started with
SMPS_OFF, which means that sdata->smps_mode was SMPS_OFF
always. Later, a nl80211 API was added to be able to start
an AP with a different AP mode. That code forgot to update
bss->req_smps and because of that, if the AP interface was
started with SMPS_DYNAMIC, we had:
sdata->smps_mode = SMPS_DYNAMIC
bss->req_smps = SMPS_OFF
That configuration made mac80211 think it needs to fire off
an action frame to any new station connecting to the AP in
order to let it know that the actual SMPS configuration is
SMPS_OFF.
Fix that by properly setting bss->req_smps in
ieee80211_start_ap.
Fixes: f699317487 ("mac80211: set smps_mode according to ap params")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Otherwise, we enable all sorts of forgeries via timing attack.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: linux-wireless@vger.kernel.org
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When mac80211 changes the channel, it also calls into the driver's
bss_info_changed() callback, e.g. with BSS_CHANGED_IDLE. The driver
may, like iwlwifi does, access more data from bss_info in that case
and iwlwifi accesses the basic_rates bitmap, but if changing from a
band with more (basic) rates to one with fewer, an out-of-bounds
access of the rate array may result.
While we can't avoid having invalid data at some point in time, we
can avoid having it while we call the driver - so set up all the
data before configuring the channel, and then apply it afterwards.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=195677
Reported-by: Johannes Hirte <johannes.hirte@datenkhaos.de>
Tested-by: Johannes Hirte <johannes.hirte@datenkhaos.de>
Debugged-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no need for the station MLME code to handle bitrates for 5
or 10 MHz channels when it can't ever create such a configuration.
Remove the unnecessary code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the driver reports the rx timestamp at PLCP start, mac80211 can
only handle legacy encoding, but the code checks that the encoding
is not legacy. Fix this.
Fixes: da6a4352e7 ("mac80211: separate encoding/bandwidth from flags")
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When a peer sends a BAR frame with PM bit clear, we should
not modify its PM state as madated by the spec in
802.11-20012 10.2.1.2.
Cc: stable@vger.kernel.org
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
A recent commit to refactor the driver and remove the hw_disabled_flags
field accidentally introduced two regressions. First, we overwrote
pf->flags which removed various key flags including the MSI-X settings.
Additionally, it was intended that we have now two flags,
HW_ATR_EVICT_CAPABLE and HW_ATR_EVICT_ENABLED, but this was not done,
and we accidentally were mis-using HW_ATR_EVICT_CAPABLE everywhere.
This patch adds the missing piece, HW_ATR_EVICT_ENABLED, and safely
updates pf->flags instead of overwriting it.
Without this patch we will have many problems including disabling MSI-X
support, and we'll attempt to use HW ATR eviction on devices which do
not support it.
Fixes: 47994c119a ("i40e: remove hw_disabled_flags in favor of using separate flag bits", 2017-04-19)
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When HSR interface is setup using ip link command, an annoying warning
appears with the trace as below:-
[ 203.019828] hsr_get_node: Non-HSR frame
[ 203.019833] Modules linked in:
[ 203.019848] CPU: 0 PID: 158 Comm: sd-resolve Tainted: G W 4.12.0-rc3-00052-g9fa6bf70 #2
[ 203.019853] Hardware name: Generic DRA74X (Flattened Device Tree)
[ 203.019869] [<c0110280>] (unwind_backtrace) from [<c010c2f4>] (show_stack+0x10/0x14)
[ 203.019880] [<c010c2f4>] (show_stack) from [<c04b9f64>] (dump_stack+0xac/0xe0)
[ 203.019894] [<c04b9f64>] (dump_stack) from [<c01374e8>] (__warn+0xd8/0x104)
[ 203.019907] [<c01374e8>] (__warn) from [<c0137548>] (warn_slowpath_fmt+0x34/0x44)
root@am57xx-evm:~# [ 203.019921] [<c0137548>] (warn_slowpath_fmt) from [<c081126c>] (hsr_get_node+0x148/0x170)
[ 203.019932] [<c081126c>] (hsr_get_node) from [<c0814240>] (hsr_forward_skb+0x110/0x7c0)
[ 203.019942] [<c0814240>] (hsr_forward_skb) from [<c0811d64>] (hsr_dev_xmit+0x2c/0x34)
[ 203.019954] [<c0811d64>] (hsr_dev_xmit) from [<c06c0828>] (dev_hard_start_xmit+0xc4/0x3bc)
[ 203.019963] [<c06c0828>] (dev_hard_start_xmit) from [<c06c13d8>] (__dev_queue_xmit+0x7c4/0x98c)
[ 203.019974] [<c06c13d8>] (__dev_queue_xmit) from [<c0782f54>] (ip6_finish_output2+0x330/0xc1c)
[ 203.019983] [<c0782f54>] (ip6_finish_output2) from [<c0788f0c>] (ip6_output+0x58/0x454)
[ 203.019994] [<c0788f0c>] (ip6_output) from [<c07b16cc>] (mld_sendpack+0x420/0x744)
As this is an expected path to hsr_get_node() with frame coming from
the master interface, add a check to ensure packet is not from the
master port and then warn.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reading /proc/net/snmp6 yields bogus values on 32 bit kernels.
Use "u64" instead of "unsigned long" in sizeof().
Fixes: 4a4857b1c8 ("proc: Reduce cache miss in snmp6_seq_show")
Signed-off-by: Christian Perle <christian.perle@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes two issues:
1) When forwarding on *,G mroutes that are in a vrf, the
kernel was dropping information about the actual incoming
interface when calling ip_mr_forward from ip_mr_input.
This caused ip_mr_forward to send the multicast packet
back out the incoming interface. Fix this by
modifying ip_mr_forward to be handed the correctly
resolved dev.
2) When a unresolved cache entry is created we store
the incoming skb on the unresolved cache entry and
upon mroute resolution from the user space daemon,
we attempt to forward the packet. Again we were
not resolving to the correct incoming device for
a vrf scenario, before calling ip_mr_forward.
Fix this by resolving to the correct interface
and calling ip_mr_forward with the result.
Fixes: e58e415968 ("net: Enable support for VRF with ipv4 multicast")
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Acked-by: David Ahern <dsahern@gmail.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZPRegAAoJEEg/ir3gV/o+UGwH/RoGd4Z8dGEkHJliBoVHTQ8d
X0iT3Pk3ho9Y8EQzLauhX9HRDTGvWIFo8uEIfe8uXsUVy9Dyb0UJ5fjYW1UQrNo1
6p08aG6I3IxYiKjfw6a/Csxc5hlxMS5g70jWbuZmTQZwAOagzvS14T9I5JFMmgcH
2fI4/cr4a0GHm4NMCObiTtuNC1CWM1llJ+zttUpcxFbpDkMPcD3SOzmmcz9eZx9c
18GaBdTOXcDkmQKIdixuxjlrQp2og2/eeHDMV8PSxjmo3yURhK97qc844sdbxCKP
wcHXwCUWXtluLBQ/6eU4LXgKcDn1aYHX38sj8YgstIc0JRG3uFCjIq+zPylBNNI=
=tb/u
-----END PGP SIGNATURE-----
Merge tag 'mlx5-fixes-2017-06-11' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
Mellanox mlx5 fixes 2017-06-11
This series contains some fixes for the mlx5 core and netdev driver.
Please pull and let me know if there's any problem.
For -stable:
("net/mlx5e: Added BW check for DIM decision mechanism") kernels >= 4.9
("net/mlx5e: Fix wrong indications in DIM due to counter wraparound") kernels >= 4.9
("net/mlx5: Remove several module events out of ethtool stats") kernels >= 4.10
("net/mlx5: Enable 4K UAR only when page size is bigger than 4K") kernels >= 4.11
*all patches apply with no issue on their -stable.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Netanel Belgazal says:
====================
Bugs fixes in ena ethernet driver
This patchset contains fixes for the bugs that were discovered so far.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
check_for_missing_tx_completions() is called from a timer
task and looking for lost tx packets.
The old implementation accumulate all the lost tx packets
and did not check if those packets were retrieved on a later stage.
This cause to a situation where the driver reset
the device for no reason.
Fixes: 1738cd3ed3 ("Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: 1738cd3ed3 ("Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the rare case where the device runs out of free rx buffer
descriptors (in case of pressure on kernel memory),
and the napi handler continuously fail to refill new Rx descriptors
until device rx queue totally runs out of all free rx buffers
to post incoming packet, leading to a deadlock:
* The device won't send interrupts since all the new
Rx packets will be dropped.
* The napi handler won't try to allocate new Rx descriptors
since allocation is part of NAPI that's not being invoked any more
The fix involves detecting this scenario and rescheduling NAPI
(to refill buffers) by the keepalive/watchdog task.
Fixes: 1738cd3ed3 ("Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch also change the mapping functions to devm_ functions
Fixes: 1738cd3ed3 ("Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bug:
"Completion context is occupied" error printout will be noticed in
dmesg.
This error will cause the admin command to fail, which will lead to
an ena_probe() failure or a watchdog reset (depends on which admin
command failed).
Root cause:
__ena_com_submit_admin_cmd() is the function that submits new entries to
the admin queue.
The function have a check that makes sure the queue is not full and the
function does not override any outstanding command.
It uses head and tail indexes for this check.
The head is increased by ena_com_handle_admin_completion() which runs
from interrupt context, and the tail index is increased by the submit
function (the function is running under ->q_lock, so there is no risk
of multithread increment).
Each command is associated with a completion context. This context
allocated before call to __ena_com_submit_admin_cmd() and freed by
ena_com_wait_and_process_admin_cq_interrupts(), right after the command
was completed.
This can lead to a state where the head was increased, the check passed,
but the completion context is still in use.
Solution:
Use the atomic variable ->outstanding_cmds instead of using the head and
the tail indexes.
This variable is safe for use since it is bumped in get_comp_ctx() in
__ena_com_submit_admin_cmd() and is freed by comp_ctxt_release()
Fixes: 1738cd3ed3 ("Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: 1738cd3ed3 ("Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixing a bug that the driver does not unmask the IO interrupts
in ndo_open():
occasionally, the MSI-X interrupt (for one or more IO queues)
can be masked when ndo_close() was called.
If that is followed by ndo open(),
then the MSI-X will be still masked so no interrupt
will be received by the driver.
Fixes: 1738cd3ed3 ("Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current flow to detect admin completion is:
while (command_not_completed) {
if (timeout)
error
check_for_completion()
sleep()
}
So in case the sleep took more than the timeout
(in case the thread/workqueue was not scheduled due to higher priority
task or prolonged VMexit), the driver can detect a stall even if
the completion is present.
The fix changes the order of this function to first check for
completion and only after that check if the timeout expired.
Fixes: 1738cd3ed3 ("Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the page size isn't bigger than 4K, there is no added value of enabling 4K
UAR feature in the Firmware.
Modified the condition of enabling the 4K UAR accordingly.
Fixes: f502d83495 ("net/mlx5: Activate support for 4K UARs")
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
DIM (Dynamically-tuned Interrupt Moderation) is a mechanism designed for
changing the channel interrupt moderation values in order to reduce CPU
overhead for all traffic types.
Each iteration of the algorithm, DIM calculates the difference in
throughput, packet rate and interrupt rate from last iteration in order
to make a decision. DIM relies on counters for each metric. When these
counters get to their type's max value they wraparound. In this case
the delta between 'end' and 'start' samples is negative and when
translated to unsigned integers - very high. This results in a false
indication to the algorithm and might result in a wrong decision.
The fix calculates the 'distance' between 'end' and 'start' samples in a
cyclic way around the relevant type's max value. It can also be viewed as
an absolute value around the type's max value instead of around 0.
Testing show higher stability in DIM profile selection and no wraparound
issues.
Fixes: cb3c7fd4f8 ("net/mlx5e: Support adaptive RX coalescing")
Signed-off-by: Tal Gilboa <talgi@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
DIM (Dynamically-tuned Interrupt Moderation) is a mechanism designed for
changing the channel interrupt moderation values in order to reduce CPU
overhead for all traffic types.
Until now only interrupt and packet rate were sampled.
We found a scenario on which we get a false indication since a change in
DIM caused more aggregation and reduced packet rate while increasing BW.
We now regard a change as succesfull iff:
current_BW > (prev_BW + threshold) or
current_BW ~= prev_BW and current_PR > (prev_PR + threshold) or
current_BW ~= prev_BW and current_PR ~= prev_PR and
current_IR < (prev_IR - threshold)
Where BW = Bandwidth, PR = Packet rate and IR = Interrupt rate
Improvements (ConnectX-4Lx 25GbE, single RX queue, LRO off)
--------------------------------------------------
packet size | before[Mb/s] | after[Mb/s] | gain |
2B | 343.4 | 359.4 | 4.5% |
16B | 2739.7 | 2814.8 | 2.7% |
64B | 9739 | 10185.3 | 4.5% |
Fixes: cb3c7fd4f8 ("net/mlx5e: Support adaptive RX coalescing")
Signed-off-by: Tal Gilboa <talgi@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Remove the following module event counters out of ethtool stats. The
reason for removing these event counters is that these events do not
occur without techinician's intervention.
module_pwr_budget_exd
module_long_range
module_no_eeprom
module_enforce_part
module_unknown_id
module_unknown_status
module_plug
Fixes: bedb7c909c ("net/mlx5e: Add port module event counters to ethtool stats")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The issue is that when we get an assert we will stop polling the health
and thus we cant enter error state when we have a real health issue.
Fixes: fd76ee4da5 ('net/mlx5_core: Fix internal error detection conditions')
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Thomas Petazzoni says:
====================
net: mvpp2: driver fixes
As requested, here is a series of patches containing only bug fixes
for the mvpp2 driver. It is based on the latest "net" branch.
Changes since v1:
- Fixed a build breakage that occurred when only PATCH 1 was only,
and not later patches in the series. Was reported by the kbuild
report on the first submission.
- Added Tested-by from Marc Zyngier on PATCH 2.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
smp_processor_id() should not be used in migration-enabled contexts. We
originally thought it was OK in the specific situation of this driver,
but it was wrong, and calling smp_processor_id() in a migration-enabled
context prints a big fat warning when CONFIG_DEBUG_PREEMPT=y.
Therefore, this commit replaces the smp_processor_id() in
migration-enabled contexts by the appropriate get_cpu/put_cpu sections.
Reported-by: Marc Zyngier <marc.zyngier@arm.com>
Fixes: a786841df7 ("net: mvpp2: handle register mapping and access for PPv2.2")
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit removes the useless remove
mvpp2_bm_cookie_{build,pool_get} functions. All what
mvpp2_bm_cookie_build() was doing is compute a 32-bit value by
concatenating the pool number and the CPU number... only to get the pool
number re-extracted by mvpp2_bm_cookie_pool_get() later on.
Instead, just get the pool number directly from RX descriptor status,
and pass it to mvpp2_pool_refill() and mvpp2_rx_refill().
This has the added benefit of dropping a smp_processor_id() call in a
migration-enabled context, which is wrong, and is the original
motivation for making this change.
Fixes: 3f518509de ("ethernet: Add new driver for Marvell Armada 375 network unit")
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The kernel may sleep under a rcu read lock in tipc_msg_reverse, and the
function call path is:
tipc_l2_rcv_msg (acquire the lock by rcu_read_lock)
tipc_rcv
tipc_sk_rcv
tipc_msg_reverse
pskb_expand_head(GFP_KERNEL) --> may sleep
tipc_node_broadcast
tipc_node_xmit_skb
tipc_node_xmit
tipc_sk_rcv
tipc_msg_reverse
pskb_expand_head(GFP_KERNEL) --> may sleep
To fix it, "GFP_KERNEL" is replaced with "GFP_ATOMIC".
Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The kernel may sleep under a rcu read lock in cfpkt_create_pfx, and the
function call path is:
cfcnfg_linkup_rsp (acquire the lock by rcu_read_lock)
cfctrl_linkdown_req
cfpkt_create
cfpkt_create_pfx
alloc_skb(GFP_KERNEL) --> may sleep
cfserl_receive (acquire the lock by rcu_read_lock)
cfpkt_split
cfpkt_create_pfx
alloc_skb(GFP_KERNEL) --> may sleep
There is "in_interrupt" in cfpkt_create_pfx to decide use "GFP_KERNEL" or
"GFP_ATOMIC". In this situation, "GFP_KERNEL" is used because the function
is called under a rcu read lock, instead in interrupt.
To fix it, only "GFP_ATOMIC" is used in cfpkt_create_pfx.
Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now sctp holds read_lock when foreach sctp_ep_hashtable without disabling
BH. If CPU schedules to another thread A at this moment, the thread A may
be trying to hold the write_lock with disabling BH.
As BH is disabled and CPU cannot schedule back to the thread holding the
read_lock, while the thread A keeps waiting for the read_lock. A dead
lock would be triggered by this.
This patch is to fix this dead lock by calling read_lock_bh instead to
disable BH when holding the read_lock in sctp_for_each_endpoint.
Fixes: 626d16f50f ("sctp: export some apis or variables for sctp_diag and reuse some for proc")
Reported-by: Xiumei Mu <xmu@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 2b30842b23 ("net: fec: Clear and enable MIB counters on imx51")
introduced fec_enet_clear_ethtool_stats(), but missed to add a stub
for the CONFIG_M5272=y case, causing build failure for the
m5272c3_defconfig.
Add the missing empty stub to fix the build failure.
Reported-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a counter problem on 32bit systems:
When the rx_bytes counter reached 2 GiB, it jumpd to (2^64 Bytes - 2GiB) Bytes.
rtnl_link_stats64 has __u64 type and atomic_long_read returns
atomic_long_t which is signed. Due to the conversation
we get an incorrect value on 32bit systems if the MSB of
the atomic_long_t value is set.
CC: Tom Parkin <tparkin@katalix.com>
Fixes: 7b7c0719cd ("l2tp: avoid deadlock in l2tp stats update")
Signed-off-by: Dominik Heidler <dheidler@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function is not defined, so no need to declare it.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz says:
====================
bnx2x: Fix malicious VFs indication
It was discovered that for a VF there's a simple [yet uncommon] scenario
which would cause device firmware to declare that VF as malicious -
Add a vlan interface on top of a VF and disable txvlan offloading for
that VF [causing VF to transmit packets where vlan is on payload].
Patch #1 corrects driver transmission to prevent this issue.
Patch #2 is a by-product correcting PF behavior once a VF is declared
malicious.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Once firmware indicates that a given VF is malicious and until
that VF passes an FLR all bets are off - PF can't know anything
is happening to the VF [since VF can't communicate anything to its PF].
But PF is currently still periodically asking device to collect
statistics for the VF which might in turn fill logs by IOMMU blocking
memory access done by the VF's PCI function [in the case VF has unmapped
its buffers].
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
