To handle the soft reboot case, the internal PLL must be
disabled in SGTL5000_CHIP_CLK_CTRL before clearing bits
SGTL5000_VCOAMP_POWERUP and SGTL5000_PLL_POWERUP in
register SGTL5000_CHIP_ANA_POWER.
Signed-off-by: Eric Nelson <eric@nelint.com>
Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Initialize CHIP_ANA_POWER to match power on defaults, which disables
ADC, DAC, and charge pumps.
In the process, remove references to the following register/bitfields
from the sgtl5000_set_power_regs routine:
CHIP_ANA_POWER/LINREG_SIMPLE_POWERUP and
CHIP_LINREG_CTRL/LINREG_VDD_MASK
And remove CHIP_ANA_POWER and CHIP_LINREG_CTRL from the set of default
registers so they don't get clobbered by sgtl5000_fill_defaults().
Signed-off-by: Eric Nelson <eric@nelint.com>
Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If an error occurs writing defaults, produce an error message but
continue writing other registers. The failure of a single write should
not cause catastrophic device failure.
In at least one occurrence, I2C writes of CHIP_ANA_POWER were nacked,
though continuing allowed the device to operate properly.
Signed-off-by: Eric Nelson <eric@nelint.com>
Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Regulator support on SGTL5000 is broken because the VDDIO and
VDDA and VDDD should be powered on before enabling MCLK as
shown in Figure 4 of [1]. This requires moving control of the
regulators from the codec block to the I2C block of the driver.
The bulk of this patch consists of swapping the codec device with
the i2c client. The new field num_supplies in struct sgtl5000_priv
is used instead of ARRAY_SIZE(supplies) to handle the special case
when the internal LDO is used instead of external VDDD.
Note that ER1 in the SGTL5000 Errata document [2] suggests that
all designs should use external VDDD.
Since the internal LDO can only be enabled after I2C is available,
there's no benefit in treating it as a regulator, so this patch
removes the regulator structure surrounding it.
Instead, a single block of code in sgtl5000_i2c_probe() performs
the initialization sequence in section 2.2.1.1 of [3] and page
26 of [1].
References:
[1] SGTL5000 data sheet
http://cache.nxp.com/files/analog/doc/data_sheet/SGTL5000.pdf
[2] SGTL5000 errata
http://cache.nxp.com/files/analog/doc/errata/SGTL5000ER.pdf
[3] SGTL5000 Initialization and programming app note
http://cache.nxp.com/files/analog/doc/app_note/AN3663.pdf
Signed-off-by: Eric Nelson <eric@nelint.com>
Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
All new designs should use external VDDD according to official
documentation. See ER1 in errata sheet:
http://cache.nxp.com/files/analog/doc/errata/SGTL5000ER.pdf
Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In is_connected_ep, when custom_stop_condition is true, need to
return the correct paths instead of con which is 0.
Fixes: 6742064aef7f('ASoC: dapm: support user-defined stop condition in dai_get_connected_widgets')
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Replace the in order struct initialisation style with explicit field
style.
The Coccinelle semantic patch used to make this change is as follows:
@decl@
identifier i1,fld;
type T;
field list[n] fs;
@@
struct i1 {
fs
T fld;
...};
@@
identifier decl.i1,i2,decl.fld;
expression e;
position bad.p, bad.fix;
@@
struct i1 i2@p = { ...,
+ .fld = e
- e@fix
,...};
Also, removed some unnecessary comments.
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
New headset mode of ALC891 for Dell.
This patch is supported Dell headset mode for ALC891.
It is only support I-phone type headset.
I think this function is only support for DELL.
This patch is test passed by Ubuntu team.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Replace the in order struct initialisation style with explicit field
style.
The Coccinelle semantic patch used to make this change is as follows:
@decl@
identifier i1,fld;
type T;
field list[n] fs;
@@
struct i1 {
fs
T fld;
...};
@@
identifier decl.i1,i2,decl.fld;
expression e;
position bad.p, bad.fix;
@@
struct i1 i2@p = { ...,
+ .fld = e
- e@fix
,...};
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
While clearing loaded module count, we should check first to see
if module list is NULL or not. Some distributions can ship with
no modules and thus list can be empty.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The module list was not initialized for Broxton DSP code, so
initialize it.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We need card to be early suspended and late resumed, so use prepare and
complete for card suspend and resume.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Senthilnathan Veppur <senthilnathanx.veppur@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The stall bits needs to comprehend the number of DSP cores
running, so update the stall and unstall register writes to
comprehend SKL_DSP_CORES_MASK values as well.
Signed-off-by: Jayachandran B <jayachandran.b@intel.com>
Signed-off-by: Ramesh Babu <ramesh.babu@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Broxton needs to send Purge firmware IPC to DSP before downloading the
firmware. The DMA id needs to be updated for that.
While at it also update Broxton boot sequence to send purge request after
power up and before yanking off reset.
Signed-off-by: Senthilnathan Veppur <senthilnathanx.veppur@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Broxton DSP needs retains code loaded during runtime_pm cycles.
But it looses that on suspend cycle, so on resume we need to
download the firmware again.
This is done by adding a new flag and based on flag status, we
download the firmware.
Signed-off-by: Jayachandran B <jayachandran.b@intel.com>
Signed-off-by: Senthilnathan Veppur <senthilnathanx.veppur@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Capture from DMIC requires that we ignore the suspend, so mark
these as ignore_suspend in bxt-rt298 machine.
Signed-off-by: Senthilnathan Veppur <senthilnathanx.veppur@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We support stereo 48Khz audio, so add these as constraints
for this card
Signed-off-by: Senthilnathan Veppur <senthilnathanx.veppur@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Like Skylake, we can support 4 channel for DMIC, so add
hw_params and constraints in the bxt-rt298 machine
While at it, also add codec1 pipe for speaker playback.
Signed-off-by: Senthilnathan Veppur <senthilnathanx.veppur@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The newly added nau8825_dai_is_active() function is only called from
the PM logic that is build-time conditional in this driver, so we get
a warning when CONFIG_PM is disabled:
sound/soc/codecs/nau8825.c:229:13: error: 'nau8825_dai_is_active' defined but not used [-Werror=unused-function]
static bool nau8825_dai_is_active(struct nau8825 *nau8825)
By replacing the #ifdef around the functions with a __maybe_unused
annotation, the code becomes more robust to this kind of problem
and we no longer get the warning while also slightly improving
readability.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: b50455fab4 ("ASoC: nau8825: cross talk suppression measurement function")
Signed-off-by: Mark Brown <broonie@kernel.org>
A recent commit made a few arrays 'const', but also added the
same attribute to a function return type, where it makes no
sense, and we get a warning when building with W=1:
sound/soc/codecs/arizona.c:1725:27: error: type qualifiers ignored on function return type [-Werror=ignored-qualifiers]
static const char * const arizona_dai_clk_str(int clk_id)
This removes it again.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SND_SOC_DAIFMT_IB_NF = 0x3 (11b) | SND_SOC_DAIFMT_IB_IF = 0x4 (100b)
creates a mask 0x7 (111b) which also includes SND_SOC_DAIFMT_NB_IF
= 0x2 (10b).
So this patch uses the traditional way to check the clock inversion.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
A PCM extension was added to I2S driver so that audio
samples are transferred using PIO mode.
The PCM supports two channels @ 16 or 32 bits with rates
32k, 44.1k and 48k.
Although the mainline I2S driver uses ALSA DMA engine the
I2S controller can be built without DMA support, therefore
this is the reason why this extension was added.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Carlos Palminha <palminha@synopsys.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: linux-snps-arc@lists.infradead.org
Cc: alsa-devel@alsa-project.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
When building with 'make W=1', we get a harmless warning about
slightly incorrect prototypes in the rcar audio driver:
sound/soc/sh/rcar/gen.c: In function 'rsnd_gen2_probe':
sound/soc/sh/rcar/gen.c:209:2: error: 'static' is not at beginning of declaration [-Werror=old-style-declaration]
This changes the 'const static' to 'static const' as it should be.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
gcc -Wextra warns about an obvious but harmless typo in the
pcm1681_writeable_reg function, which has an extra 'register
keyword', and in pcm179x, which has a second copy of that
declaration:
sound/soc/codecs/pcm1681.c:76:42: error: 'register' is not at beginning of declaration [-Werror=old-style-declaration]
sound/soc/codecs/pcm179x.c:62:42: error: 'register' is not at beginning of declaration [-Werror=old-style-declaration]
For consistency with the rest of the file, I'm changing this from
'unsigned register' to 'unsigned int', which has the same meaning
but causes no warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
When GPIOLIB is disabled, we don't see the declarations from
gpio/consumer.h, so we have to include the header explicitly
to avoid this build error:
sound/soc/codecs/cs53l30.c: In function 'cs53l30_i2c_probe':
sound/soc/codecs/cs53l30.c:931:24: error: implicit declaration of function 'devm_gpiod_get_optional' [-Werror=implicit-function-declaration]
cs53l30->reset_gpio = devm_gpiod_get_optional(dev, reset,
^~~~~~~~~~~~~~~~~~~~~~~
sound/soc/codecs/cs53l30.c:932:13: error: 'GPIOD_OUT_LOW' undeclared (first use in this function)
GPIOD_OUT_LOW);
^~~~~~~~~~~~~
sound/soc/codecs/cs53l30.c:932:13: note: each undeclared identifier is reported only once for each function it appears in
sound/soc/codecs/cs53l30.c:939:3: error: implicit declaration of function 'gpiod_set_value_cansleep' [-Werror=implicit-function-declaration]
gpiod_set_value_cansleep(cs53l30->reset_gpio, 1);
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The TWL6040 ASoC support has recently started turning on CLK_TWL6040,
but that fails to build when CONFIG_COMMON_CLK is disabled:
warning: (SND_OMAP_SOC_OMAP_ABE_TWL6040) selects CLK_TWL6040 which has unmet direct dependencies (COMMON_CLK && TWL6040_CORE)
0xF18E38F6 Thu Jun 9 18:57:32 CEST 2016 failed
In file included from ../include/linux/clocksource.h:18:0,
from ../drivers/clocksource/timer-nps.c:34:
../include/linux/of.h:1005:20: error: comparison of distinct pointer types lacks a cast [-Werror]
.data = (fn == (fn_type)NULL) ? fn : fn }
^
This adds a dependency to avoid the invalid configuration.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 443500a392 ("ASoC: omap: Kconfig: SND_OMAP_SOC_OMAP_ABE_TWL6040 to select CLK_TWL6040")
Signed-off-by: Mark Brown <broonie@kernel.org>
The wm8985 driver is now user-selectable, but building it with
I2C disabled results in a link failure:
sound/built-in.o: In function `wm8985_i2c_probe':
:(.text+0x44914): undefined reference to `__devm_regmap_init_i2c'
sound/built-in.o: In function `wm8985_exit':
:(.exit.text+0x3d8): undefined reference to `i2c_del_driver'
sound/built-in.o: In function `wm8985_modinit':
:(.init.text+0x1454): undefined reference to `i2c_register_driver'
This adds a Kconfig dependency the way that the other codec
drivers have it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 811e66de22 ("ASoC: wm8985: add support for WM8758")
Signed-off-by: Mark Brown <broonie@kernel.org>
If the DSP is powered down whilst a compressed stream is being processed
we should treat this as a fatal error, clearly the stream is no longer
valid.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If we encounter a fatal error on the compressed stream call the new
snd_compr_stop_error to shutdown the stream and allow the core to
inform user-space that the stream is no longer valid.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Reviewed-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently, the avail IOCTL doesn't pass any error status, which
means typically on error it simply shows no data available. This
can lead to situations where user-space is waiting indefinitely
for data that will never come as the DSP has suffered an
unrecoverable error.
Add snd_compr_stop_error which end drivers can call to indicate
the stream has suffered an unrecoverable error and stop it. The
avail and poll IOCTLs are then updated to report if the stream is
in an error state to user-space. Allowing the error to propagate
out. Processing of the actual snd_compr_stop needs to be deferred
to a worker thread as the end driver may detect the errors during
an existing operation callback.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In case of error, the function syscon_regmap_lookup_by_phandle() returns
ERR_PTR() and never returns NULL. The NULL test in the return value check
should be replaced with IS_ERR().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mark Brown <broonie@kernel.org>
The OUT4L and OUT4R widgets are not registered PRE_PMU or POST_PMD
events, as such the manual speaker enable on wm5102 does not actually
ever run. Furthermore since the issue actually only affected rev B of
the silicon which never shipped in volume, simply remove the work around
from the code.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The audio trace firmware on wm5102 only supports 4 channels correct
the DAI driver structure to reflect this.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Output 3 is stereo on wm5110 and all inputs/outputs should have a
connection to SYSCLK. This patch adds the missing DAPM route.
Signed-off-by: Ajit Pandey <ajit.pandey@soctronics.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The cross talk measurement function can reduce cross talk across the JKTIP
HPL) and JKR1(HPR) outputs which measures the cross talk signal level to
determine what is the cross talk reduction gain. This system works by
sending a 23Hz -24dBV sine wave into the headset output DAC and through
the PGA. The output of the PGA is then connected to an internal current
sense which measures the attenuated 23Hz signal and passing the output to
an ADC which converts the measurement to a binary code. With two separated
measurement, one for JKR1(HPR) and the other JKTIP(HPL), measurement data
can be separated read in IMM_RMS_L for HSR and HSL after each measurement.
Thus, the measurement function has four states to complete whole sequence.
(1)Prepare state : Prepare the resource for detection and transfer to HPR
IMM stat to make JKR1(HPR) impedance measure.
(2)HPR IMM state : Read out orignal signal level of JKR1(HPR) and transfer
to HPL IMM state to make JKTIP(HPL) impedance measure.
(3)HPL IMM state : Read out cross talk signal level of JKTIP(HPL) and
transfer to IMM state to determine suppression sidetone gain.
(4)IMM state : Computes cross talk suppression sidetone gain with orignal
and cross talk signal level. Apply this gain and then restore codec con-
figuration. Then transfer to Done state for ending.
In order to get the cross talk suppression sidetone gain, we need the
function to compute log10 value and the result is round off to 3 decimal.
This function takes reference to dvb-math. The source code locates as the
following. "Linux/drivers/media/dvb-core/dvb_math.c"
Then, the orignal and cross talk signal vlues need to be characterized.
The sidetone value can be converted to decibel with the equation below.
sidetone = 20 * log (original signal level / crosstalk signal level)
Besides, the state machine for cross talk process needs interruptions to
trigger worked. We have the RMS intrruption enabled with the internal VCO
clock when headset connected. In the interrupt handler, the driver will
judge the headset is high impedance or not. If yes, the cross talk supp-
ression shouldn't apply and do nothing but relieve the protection raised
before. Otherwise, apply the cross talk suppression in the headset and
start the process.
Because the process spends a lot of time, there is an resource race issue
easily between the application and interruption. They will control codec
power and clock concurrently. In one situaiton, the jack is inserted when
playback, and then the application changes to headset device. The applica-
tion prepares the playback and interrupt handler raises work for cross
talk process together. For this case, the solution is that driver delays
soc jack report until cross talk process completes. The mechanism can
avoid application to do playback preparation before cross talk detection
is still working.
In another situaiton, the system suspends when playback. After resume, the
system restarts playback, and meanwhile jack detection restarts. The play-
back preparation and cross talk process triggered by interruptions happens
concurrently. For the case, the driver provides the semaphone to syn-
chronize the playback and interrupt handler. In order to avoid the play-
back interfered by cross talk process, the driver make the playback prepa-
ration halted until cross talk process finish. After codec resume, the
driver finds the codec dai is active, and then the driver raises the pro-
tection for cross talk function to avoid the playback recovers before
cross talk process finish.
The driver also provides cancel method to forcely cancel the cross talk
task and restores the configuration to original status. Before the codec
remove, ejection, or suspend, the driver is obliged to cancel the cross
talk detection process. It can reduce the risk of failure when quickly and
continually doing jack insertion and ejection.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The McBSP sidetone (in OMAP3 McBSP2 and 3 module) is working with the
module's interface clock. When the sidetone is enabled the iclk must not
idle because it will result in choppy sidetone.
Switch to use the new callback for handling the iclk allow/deny idle
configuration.
For this the driver needs to get the module's ick clock and pass the clk
pointer to the callback.
In DT boot, the pdata-quirk is going to set up the callback for the driver
so save it if it is set in the pdata of the device.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The function will do more then removing the sysfs files in the future.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Multiple devices from the ADAU family share the same PLL structure and
configuration register layout. Introduce a new helper module that can be
used to calculated the PLL configuration registers based on a specified
input frequency and the desired output frequency of the PLL.
The ADAU1761/ADAU1781 and ADAU1373 drivers are updated to make use of this
new helper module. But future drivers for additional devices from the ADAU
family are also expected to make use of it.
In anticipation of sharing more infrastructure code between different
devices from the ADAU family the new module is called adau-utils.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
AUDIO-CLKOUTn can asynchronizes with L/R clock.
AUDIO-CLKOUTn synchronizes with L/R clock is now default behavior.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Kabylake shows up as PCI ID 0xa171. And Kabylake-LP as 0x9d71.
Since these are similar to Skylake add these to SKL_PLUS macro
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The device has multiple control interfaces, I2C and SPI. The I2C interface
mainly controls the register settings of codec. The SPI interface is in
order to provide the high speed transmission of data. For example, high
bandwidth memory read/write of DSP. The patch adds the rt5514 SPI driver
for loading the firmware of DSP and retrieving the voice data from DSP
after the system is waked up by specific voice.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Don't update the runtime_delay in pointer query, delay need to
reported as part of soc driver ops delay function. The delay
value overwritten by ASoC core so this is dummy code and hence
removing it.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For pass through pipe, Host and Link DMA id's are valid,
instead of overwriting the params set the host and link
based on pipe type.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DSP pipe type can be a pass through or it can be processing pipe.
In case of pass through pipe, it is a single pipeline with both
host and link copier in the same pipeline.
Identify the DSP pipe type if it pass through or not. Pass through
pipe is identified by checking if it has both host and link copier
in the same pipeline.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We need to Identify the DSP pipe type and based on it being a pass
thru pipeline or not, we need to copy the pipeline params.
Pipe to widget mapping was earlier done in pre PMD widget handler,
but since the pipe type would now be required in hw_params for
bypass pipelines we need to move this to be done during the ASoC
probe of the platform component.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
On suspend firmware is re-initialized so resources are reset inside
firmware. Driver should also clear the firmware counters at this time.
Signed-off-by: Dharageswari R <dharageswari.r@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When DSP pipe/module is not initialized successfully, memory/mcps
is not allocated. So check the pipe/module state to avoid freeing
up of unallocated memory/mcps. And allocate resources when pipe/
module is initialized successfully.
Signed-off-by: Dharageswari R <dharageswari.r@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SW needs to set the PGCTL.LSRMD = 1 to disable LPSRAM retention
feature,otherwise it may lead to SRAM ECC Errors.
Signed-off-by: Dharageswari R <dharageswari.r@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If pipeline is not STARTED, we do not need to pause pipeline while
deleting.
Signed-off-by: Dharageswari R <dharageswari.r@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When pipe is stopped/Paused, set the pipe state to paused instead
of created.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In case of XRUN recovery PCM prepare will be called. In this case
Host/Link DMAs are reset and reconfigured, hence the corresponding
FE/BE pipe needs to be reset in order to get to a clean state.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Tested with Lenovo Ultradock. Fixes the non-working headphone jack on
the docking unit.
Signed-off-by: Torsten Hilbrich <torsten.hilbrich@secunet.com>
Tested-by: Torsten Hilbrich <torsten.hilbrich@secunet.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The register setting for HP Playback Volume is inverted. So, set
the invert flag in SOC_DOUBLE_TLV.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The register setting for HP Playback Volume is inverted. So, set
the invert flag in SOC_DOUBLE_TLV.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
System workqueues have been able to handle high level of concurrency
for a long time now and there's no reason to use dedicated workqueues
just to gain concurrency. Since aica_queue for AICA sound
driver has workitem dreamcastcard->spu_dma_work (maps to run_spu_dma)
which is involved in aica dma transfers and is not being used on a memory
reclaim path, dedicated aica_queue has been replaced with the
use of system_wq.
Unlike a dedicated per-cpu workqueue created with create_workqueue(),
system_wq allows multiple work items to overlap executions even on
the same CPU; however, a per-cpu workqueue doesn't have any CPU
locality or global ordering guarantees unless the target CPU is
explicitly specified and thus the increase of local concurrency
shouldn't make any difference.
Since the work items could be pending, flush_work() has been used in
snd_aicapcm_pcm_close() to ensure that there is no pending task while
disconnecting the driver.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
m32r allmodconfig build is failing with the error:
ERROR: "bad_dma_ops" [sound/soc/atmel/snd-soc-atmel-pcm-pdc.ko] undefined!
The code is using DMA but the related dependency is not mentioned in the
Kconfig.
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Clean up the header files regarding to hdmi audio so the omap-hdmi-audio.h
file will only need to include the platform_data/omapdss.h file.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
CC: Mark Brown <broonie@kernel.org>
CC: Jyri Sarha <jsarha@ti.com>
CC: Liam Girdwood <liam.r.girdwood@linux.intel.com>
There is typo in the name of biquad filter coefficients control.
The patch is to fix the typo.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the pin configuration value of this machine into the pin_quirk
table to make DELL1_MIC_NO_PRESENCE apply to this machine.
Signed-off-by: AceLan Kao <acelan.kao@canonical.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
m32r allmodconfig build is failing with the error:
ERROR: "bad_dma_ops" [sound/soc/fsl/snd-soc-fsl-asrc.ko] undefined!
The code is using DMA but the related dependency is not mentioned in the
Kconfig.
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
The new machine's MCLK source is from mt8173 which is dynamic from
sampling rate*256. This patch provides the selection for device tree.
Signed-off-by: PC Liao <pc.liao@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support for the ADAU7002 PDM-to-I2S/TDM converter. The
ADAU7002 takes a stereo PDM signal (e.g. from two digital microphones) and
converts it into a I2S/TDM PCM stream. The chip does not have a
programmable control interface and the driver simply describes the static
capabilities of the chip.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
SND_SOC_HDMI_CODEC can be enabled without HDMI support, leading
to a link error:
In function `hdmi_codec_hw_params':
sound/soc/codecs/hdmi-codec.c:188: undefined reference to `hdmi_audio_infoframe_init'
sound/built-in.o:(.debug_addr+0x1a5c0): undefined reference to `hdmi_audio_infoframe_init'
This changes the Kconfig file to select HDMI, as the other codec using
hdmi_audio_infoframe_init already does.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Regcache_sync() might fail. So this patch adds a return value Check for it.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Acked-by: Paul Handrigan <Paul.Handrigan@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Volume controls should end with 'Volume', so this patch renames them for
ADC preamplifier.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Acked-by: Paul Handrigan <Paul.Handrigan@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of modifying the static pdata struct per McASP instance we need to
allocate pdata for each McASP.
This way we can avoid configuration leakage from prior McASP to McASP
drivers probed at later time.
Reported-by: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The TX and RX offset is different for each serializers when using the CFG
port for DMA access.
When using the CFG port only one serializer can be used per direction so
print error message and only configure the first serializer's offset.
Reported-by: Misael Lopez Cruz <misael.lopez@ti.com>
Suggested-by: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The TX and RX offset is different for each serializers when using the CFG
port for DMA access.
When using the CFG port only one serializer can be used per direction so
print error message and only configure the first serializer's offset.
Reported-by: Misael Lopez Cruz <misael.lopez@ti.com>
Suggested-by: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
So far, we enabled the loopback mixing control as default, as this
behavior made somewhat compatible with the earlier HD-audio drivers
for Realtek & co. However, it's getting annoying as we've got more
and more bug reports about the noise coming from the loopback route.
Since the loopback mixing is used fairly rarely and often harmful
(e.g. using PA), let's get rid of the default turn-on lines.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds bxt_da7219_max98357a_i2s machine driver
entry into machine table
Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds Broxton-P I2S machine driver which uses
DA7219 and MAX98357A codecs.
Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add channel 1 and 2 input mixer registers and the related ALSA mixer
controls for TAS5717/19 chips.
The mixer control coefficients on the chip are linear in the range
-3.99999 to +3.99999, encoded in 3.23 number format.
In this patch the mixer controls are limited to 128 values
from 0.0 to 1.0 in 1/64 steps.
Signed-off-by: Petr Kulhavy <brain@jikos.cz>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Lenovo 100S netbook has a codec controller for which there is a
driver, but doesn't know how to access the device. This adds the
necessary ACPI table for the driver to find the device.
Device (TTLV)
{
Name (_ADR, Zero) // _ADR: Address
Name (_HID, "10TI3100") // _HID: Hardware ID
Name (_CID, "10TI3100") // _CID: Compatible ID
Name (_DDN, "TI TLV320AIC3100 Codec Controller ") // _DDN: DOS Device Name
Name (_UID, One) // _UID: Unique ID
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Tested-by: Jan Schmidt <jan@centricular.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This driver does not do anything special in module init/exit. This patch
eliminates the module init/exit boilerplate code by utilizing the
module_isa_driver macro.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This driver does not do anything special in module init/exit. This patch
eliminates the module init/exit boilerplate code by utilizing the
module_isa_driver macro.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This driver does not do anything special in module init/exit. This patch
eliminates the module init/exit boilerplate code by utilizing the
module_isa_driver macro.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This driver does not do anything special in module init/exit. This patch
eliminates the module init/exit boilerplate code by utilizing the
module_isa_driver macro.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This driver does not do anything special in module init/exit. This patch
eliminates the module init/exit boilerplate code by utilizing the
module_isa_driver macro.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This driver does not do anything special in module init/exit. This patch
eliminates the module init/exit boilerplate code by utilizing the
module_isa_driver macro.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This driver does not do anything special in module init/exit. This patch
eliminates the module init/exit boilerplate code by utilizing the
module_isa_driver macro.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This driver does not do anything special in module init/exit. This patch
eliminates the module init/exit boilerplate code by utilizing the
module_isa_driver macro.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This driver does not do anything special in module init/exit. This patch
eliminates the module init/exit boilerplate code by utilizing the
module_isa_driver macro.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This driver does not do anything special in module init/exit. This patch
eliminates the module init/exit boilerplate code by utilizing the
module_isa_driver macro.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This driver does not do anything special in module init/exit. This patch
eliminates the module init/exit boilerplate code by utilizing the
module_isa_driver macro.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The driver changes jack type detection interruption to non-clock archi-
tecture for less 1mW power saving. The architecture is called manual mode
jack detection. It has no hardware debounce, no jack type detection, but
only detecting jack insertion. After jack insertion, the driver will
switch to auto mode jack detection with internal clock which can detect
microphone, jack type and do hardware debounce.
The manual architecture has these main changes including codec initiation,
interruption, clock control, and power management. When codec initiation
or system resume, the clock is closed as jack insertion detection at man-
ual mode, and bypass debounce circuit. These configurations move to resume
setup function when setup bias level after resume.
When jack insertion detection happens, the manual mode turns off and make
configuration about jack type detection interruption at auto mode in auto
irq setup function which can detect microphone and jack type. The inter-
ruption will switch to manual mode again with clock free until jack ejec-
tion happens.
The system clock configuration adds clock disable option which can disable
internal VCO clock. Before the system clock change, there is an restric-
tion added to make sure clock disabled and not config any clock when no
headset connected.
In power management, we involve the solution about races and jack detec-
tion in resume from Ben Zhang in the following patch and list his comment.
[PATCH] ASoC: nau8825: Fix jack detection across suspend
"Jack plug status is rechecked at resume to handle plug/unplug
in S3 when the chip has no power."
"Suspend/resume callbacks are moved from the i2c dev_pm_ops to
snd_soc_codec_driver. soc_resume_deferred is a delayed work
which may trigger nau8825_set_bias_level. The bias change races
against dev_pm_ops, causing jack detection issues.
soc_resume_deferred ensures bias change and snd_soc_codec_driver
suspend/resume are sequenced correctly."
Change SAR widget to supply type which can prevent the codec keeping at
SND_SOC_BIAS_ON during suspend. The codec suspend function can just invoke
normally.
Before the system suspends, the driver turns off all interruptions. Keep
the interruption quiet before resume setup completes. The ADC channel will
be disabled which is needed for interruptions at audo mode.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add programmable biquad filter configuration control for user space.
The filter is configurable for low pass filters, high pass filters,
Notch filter, etc in the ADC and DAC path.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This machine driver can support 2 or 4 DMIC configuration, so
apply the ch constraint according to driver pdata.
Signed-off-by: Yong Zhi <yong.zhi@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This machine driver can support 2 or 4 DMIC configuration, so
apply the ch constraint according to driver pdata.
Signed-off-by: Yong Zhi <yong.zhi@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds Cygnus audio DMA driver. It supports playback
and capture modes and uses ringbuffers for data transfer.
Signed-off-by: Lori Hikichi <lhikichi@broadcom.com>
Signed-off-by: Simran Rai <ssimran@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Arun Parameswaran <arunp@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds Cygnus audio DAI driver. It supports I2S, TDM
and SPDIF modes and uses three clocks derived from PLL.
This patchset has been tested on Cygnus wireless audio
bcm958305K board.
Signed-off-by: Lori Hikichi <lhikichi@broadcom.com>
Signed-off-by: Simran Rai <ssimran@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Arun Parameswaran <arunp@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the suspend callback to accompany the existing resume operation.
With the suspend/resume callbacks the regmap (regcache) state handling can
follow the recommended sequence.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Static checker warns:
Pointer 'hlink' returned from call to function 'snd_hdac_ext_bus_get_link'
at line may be NULL and will be dereferenced"
So we should always check the return of snd_hdac_ext_bus_get_link() before
referencing the link pointer
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
64-bit builds would generate a warning when we passed the core number as
a pointer through the notifier data:
sound/soc/codecs/cs47l24.c:1091:13: warning: cast to pointer from
integer of different size [-Wint-to-pointer-cast]
(void *)i);
Rather than just fix this up with more casting add a data structure that
holds information for the notifier chain. This will make it easier to
add additional information in the future as well.
Fixes: 7baa7e2490 ("ASoC: arizona: Add event notification on voice trigger events")
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Broxton uses different offset in manifest for parsing module
table. So invoke common parsing utility from broxton using
broxton offset.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SKylake uses different offset in manifest for parsing module
table. So invoke common parsing utility from skylake using
skylake offset.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Module params like module_id and loadable flag can be changed
in the DSP Firmware. These are kept in the firmware manifest
and driver should read these values from this manifest.
So, add support to parse the DSP firmware manifest and
read these module params.
Signed-off-by: Shreyas NC <shreyas.nc@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Broxton firmrware comes with extended manifest so invoke
skl_dsp_strip_extended_manifest() to check and strip
Signed-off-by: Ramesh Babu <ramesh.babu@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Future firmware updates may comes with extended manifest so invoke
skl_dsp_strip_extended_manifest() to check and strip
Signed-off-by: Shreyas NC <shreyas.nc@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We have firmware pointer is driver context, so use that instead
of local pointer.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some upcoming platforms like broxton etc have extended manifest
in firmware binary. This is not required to be downloaded to DSP.
So driver needs to strip this before downloading.
Add a utility function to check if a header exists, and remove it
in that case
Signed-off-by: Ramesh Babu <ramesh.babu@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Skylake can be configured with either both 2 and 4 channel DMIC
array, or 2 channel DMIC array only, this patch provides an API to
retrieve the DMIC info from nhlt.
Signed-off-by: Yong Zhi <yong.zhi@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In current simple-card, platform is handled as special case,
but, the code is not readable.
This patch makes platform to use asoc_simple_card_sub_parse_of()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The WM8758 chip is almost identical to WM8985 with the difference that it
doesn't feature the AUX input. This patch adds the WM8758 support into the
WM8985 driver.
The chip selection is done by the I2C name. The SPI probe supports only
the WM8985.
Signed-off-by: Petr Kulhavy <petr@barix.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The WM8758 chip is almost identical to WM8985 with the difference that it
doesn't feature the AUX input. This patch adds the register definitions
for WM8758 specific bit fields to the header file.
Signed-off-by: Petr Kulhavy <petr@barix.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The datasheet uses decimal numbers for the register addresses, convert the
register values from hexadecimal to decimal and introduce macro for the
register definitions. This way it is easier to look up registers in the
documentation.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
TAS571x features multiple biquad filters. Their coefficients
are stored in 20-byte registers, which cannot be supported by
regmap.
This patch adds read and write functions for multi-word (32-bit) register
access and mixer controls for the biquads. The multi-word read/write
functions can be used in the future to implement other features like DRC or
output mixer.
Signed-off-by: Petr Kulhavy <brain@jikos.cz>
Signed-off-by: Mark Brown <broonie@kernel.org>
We have been using "simple-audio-card" for Odroid X2/U3 boards,
as can be seen from sound node in arch/arm/boot/dts/
exynos4412-odroid-common.dtsi. A dedicated machine driver is not
needed and it is removed in this patch.
There is no dts files using "samsung,odroidx2-audio" or
"samsung,odroidu3-audio" compatible strings.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Simplify the code a little by using a standard function for
getting the match data.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
samsung_dai_type_pri is not referenced anywhere so remove it.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
"samsung-i2sv4" identifier was previously used for the I2S device
of the S5PV210 SoCs, it can be removed now when s5pv210 is a dt-only
platform.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
this patch make it more reasonable and readable, because when we chose
I2S_CKR_TRCM_TXONLY, we only output clk_lrck_tx, and hardware need to
confirm this signal is wired to external codec lrck_tx/rx at the same time.
for convenience, we just handle lrck_txonly if we enable symmetric_rates
in driver and dai_link. otherwise, we use the separate lrck_tx/rx.
Signed-off-by: Sugar Zhang <sugar.zhang@rock-chips.com>
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Physically there is a jackset which includes a Headphone and a Jackset
Mic pin. The patch add thw two pins with the correct pin name so the
DAPM management can find the pin and make the jack detection and event
reporting work again.
The patch also shut up the following error:
rockchip-snd-max98090 sound: ASoC: DAPM unknown pin Headset Jack
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The path Headset Mic --> MICBIAS is wrong because connects a non-supply
widget as a source with a supply widget as a sink. It's the other way
around:
MICBIAS (source) --> Headset Mic (sink).
This patch also shut up the following error message:
rockchip-snd-max98090 sound: Connecting non-supply widget to supply widget is not supported (Headset Mic -> MICBIAS)
rockchip-snd-max98090 sound: ASoC: no dapm match for Headset Mic --> (null) --> MICBIAS
rockchip-snd-max98090 sound: ASoC: Failed to add route Headset Mic -> direct -> MICBIAS
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit f2ed6b0764 ("ASoC: Make aux_dev more like a generic
component") caused a regression on this driver, since now a
kernel oops is seen when rockchip-mac98090 driver is loaded.
That commit changed the probing of aux_devs before checking
new DAI links, so for this driver rk_98090_headset_init is
called before rk_init and then the kernel oops due a NULL
pointer dereference inside rk_98090_headset_init function
since there is a call that tries to access the jack pointer
which has not been allocated yet.
This is the call chain that causes the crash:
rk_98090_headset_init
-> ts3a227e_enable_jack_detect
-> snd_jack_set_key
rk_init
-> snd_soc_card_jack_new
This patch moves the new jack object creation from rk_init
to rk_98090_headset_init function making sure the jack is
created before is accessed.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There are 3 i2s sdio pins, which iomux mode is as follows:
- sdi3_sdo1
- sdi2_sdo2
- sdi1_sdo3
we need to configure these pins' iomux mode via the GRF register
when use multi channel playback/capture.
Signed-off-by: Sugar Zhang <sugar.zhang@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This platform_driver does not need to set an owner as it will be
populated by the driver core.
Generated by scripts/coccinelle/api/platform_no_drv_owner.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
McPDM module receives it's functional clock from external source. This
clock is the pdmclk provided by the twl6040 audio IC. If the clock is not
available all register accesses to McPDM fails and the module is not
operational.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Implement ASoC's suspend and resume callbacks.
Since McPDM does not use pcm_trigger for start and stop of the stream due
to strict sequencing needs with the twl6040, the callbacks will stop and
restart the McPDM in case the board suspended during audio activity.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The DS4_WD_EN bit is only touched before calling omap_mcpdm_open_streams().
Move it inside of that function for simplicity.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The pdmclk is needed for McPDM. It is generated by twl6040.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The I2C driver has an i2c_device_id array but that information isn't
exported to the module using the MODULE_DEVICE_TABLE() macro. So the
module autoloading won't work if the I2C device is registered using
OF or legacy board files due missing alias information in the module.
The issue was found using Kieran Bingham's coccinelle semantic patch:
https://lkml.org/lkml/2016/5/10/520
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The default value of DAC channel select is reverse in codec.
For normal usage, switch the channel select when codec bootup.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The interrupt clock is gated by x1[10:8], one of them needs to be enabled
all the time for interrupts to happen. We change codec to enable ADC
because it's helpful to reduce playback pop noise.
Don't use force enable pin to enable ADC instead of ADC widget event.
That won't interfere DAPM operation and let bias work normally.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Decrease internal clock frequency for power saving when standby.
But clock divider needs restore when MCLK as system clock in playback.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In FLL calculation, increase VCO/DCO frequency for better performance.
Besides, have different register configuration according to fraction or not
when apply FLL parameters.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Extend FLL clock source selection. The source can be from MCLK, BCLK or FS.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Because MCLK opens later and closes earlier than codec, this patch
changes the order of MCLK clock configuration.
Signed-off-by: PC Liao <pc.liao@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is a driver for the MAX9860 Mono Audio Voice Codec.
https://datasheets.maximintegrated.com/en/ds/MAX9860.pdf
This driver does not support sidetone since the DVST register field is
backwards with the mute near the maximum level instead of the minimum.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Mark Brown <broonie@kernel.org>
Only mono channel is allowed for refcap device.
Signed-off-by: Yong Zhi <yong.zhi@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add constraint for ref DMIC to match with the
topology firmware config.
Signed-off-by: Yong Zhi <yong.zhi@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This function stub should have been 'static' in the original patch
so that multiple uses of the header file (in different drivers)
will not cause multiple function definitions.
sound/soc/intel/boards/built-in.o: In function `sst_acpi_find_name_from_hid':
(.text+0x560): multiple definition of `sst_acpi_find_name_from_hid'
sound/soc/intel/atom/built-in.o:(.text+0x10610): first defined here
../scripts/Makefile.build:369: recipe for target 'sound/soc/intel/built-in.o' failed
Fixes: f17131a93f: add function stub when ACPI is not enabled
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Helper functions to disable and enable the I2S interrupts were
added. Only the interrupts of the used channels are enabled.
Also, there is no need to enable irqs at dw_i2s_config(), they
are already enabled at startup.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Carlos Palminha <palminha@synopsys.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: linux-snps-arc@lists.infradead.org
Cc: alsa-devel@alsa-project.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently in situations where a normal CODEC to CODEC link follows a
DPCM DAI, an error in the following form will be logged:
ASoC: can't get [playback|capture] BE for <widget name>
ASoC: no BE found for <widget name>
This happens because all widgets in a path containing a DPCM DAI will
be passed to dpcm_add_paths, which will try to interpret the CODEC<->CODEC
as if it were a DPCM DAI, in turn causing the error.
This patch aims to resolve the described issue by stopping the DPCM graph
walk, initiated from dpcm_path_get, at the first widget associated with
a DPCM BE.
Signed-off-by: Piotr Stankiewicz <piotrs@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Certain situations may warrant examining DAPM paths only to a certain
arbitrary point, as opposed to always following them to the end. For
instance, when establishing a connection between a front-end DAI link
and a back-end DAI link in a DPCM path, it does not make sense to walk
the DAPM graph beyond the first widget associated with a back-end link.
This patch introduces a mechanism which lets a user of
dai_get_connected_widgets supply a function which will be called for
every node during the graph walk. When invoked, this function can
execute arbitrary logic to decide whether the walk, given a DAPM widget
and walk direction, should be terminated at that point or continued
as normal.
Signed-off-by: Piotr Stankiewicz <piotrs@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
CS53L30 is a Quad-Channel ADC from Cirrus Logic with an I2S/TDM DAI.
So this patch adds a codec driver for CS53L30 that includes 4-channel
24-bit recording and TDM mode supports.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The DSP uses an IRQ to indicate data is available on the compressed
stream. For voice trigger use-cases the first such IRQ can be considered
an indication that the user has spoken the key phrase triggering the
firmware. Provide a means for the ADSP code to communicate back to the
calling driver whether an IRQ should be considered as trigger event or
not.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In some situations the voice control firmware will by used
to only provide a trigger notification event. In this case a
compressed stream will not be opened by user-space, as such we
need to provide a virtual output to power on the DSP in this
use-case. This patch adds a virtual output 'DSP Voice Trigger'
that can be used for this, and a switch that lets it be connected
to the core when required.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The intent is for SYSCLK to be tied to all input and output widgets such
that it turns on whenever the chip is in use. It is not tied to the DRC
signal activity detect virtual outputs, whilst in practice this is
unlikely to cause an issue (as an input will likely also be powered up)
best to correct.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This platform_driver does not need to set an owner as it will be
populated by the driver core.
Generated by scripts/coccinelle/api/platform_no_drv_owner.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Inform the notifier chain if the DSP recognises a voice trigger.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a notifier chain that can be used from the machine driver to catch
events generated by the CODEC.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Support new codecs for ALC700/ALC701/ALC703.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
That is some different register for ALC255 and ALC256.
ALC256 can't fit with some ALC255 register.
This issue is cause from LDO output voltage control.
This patch is updated the right LDO register value.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is the second update round for 4.7-rc1. Most of changes are
about the pending ASoC updates and fixes, including a few new
drivers. Below are some highlights:
ASoC:
- New drivers for MAX98371 and TAS5720
- SPI support for TLV320AIC32x4, along with the module split
- TDM support for STI Uniperf IPs
- Remaining topology API fixes / updates
HDA:
- A couple of Dell quirks and new Realtek codec support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=uNKQ
-----END PGP SIGNATURE-----
Merge tag 'sound-4.7-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull more sound updates from Takashi Iwai:
"This is the second update round for 4.7-rc1. Most of changes are
about the pending ASoC updates and fixes, including a few new drivers.
Below are some highlights:
ASoC:
- New drivers for MAX98371 and TAS5720
- SPI support for TLV320AIC32x4, along with the module split
- TDM support for STI Uniperf IPs
- Remaining topology API fixes / updates
HDA:
- A couple of Dell quirks and new Realtek codec support"
* tag 'sound-4.7-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (63 commits)
ALSA: hda - Fix headset mic detection problem for one Dell machine
spi: spi-ep93xx: Fix the PTR_ERR() argument
ALSA: hda/realtek - Add support for ALC295/ALC3254
ASoC: kirkwood: fix build failure
ALSA: hda - Fix headphone noise on Dell XPS 13 9360
ASoC: ak4642: Enable cache usage to fix crashes on resume
ASoC: twl6040: Disconnect AUX output pads on digital mute
ASoC: tlv320aic32x4: Properly implement the positive and negative pins into the mixers
rcar: src: skip disabled-SRC nodes
ASoC: max98371 Remove duplicate entry in max98371_reg
ASoC: twl6040: Select LPPLL during standby
ASoC: rsnd: don't use prohibited number to PDMACHCRn.SRS
ASoC: simple-card: Add pm callbacks to platform driver
ASoC: pxa: Fix module autoload for platform drivers
ASoC: topology: Fix memory leak in widget creation
ASoC: Add max98371 codec driver
ASoC: rsnd: count .probe/.remove for rsnd_mod_call()
ASoC: topology: Check size mismatch of ABI objects before parsing
ASoC: topology: Check failure to create a widget
ASoC: add support for TAS5720 digital amplifier
...
Most users of IS_ERR_VALUE() in the kernel are wrong, as they
pass an 'int' into a function that takes an 'unsigned long'
argument. This happens to work because the type is sign-extended
on 64-bit architectures before it gets converted into an
unsigned type.
However, anything that passes an 'unsigned short' or 'unsigned int'
argument into IS_ERR_VALUE() is guaranteed to be broken, as are
8-bit integers and types that are wider than 'unsigned long'.
Andrzej Hajda has already fixed a lot of the worst abusers that
were causing actual bugs, but it would be nice to prevent any
users that are not passing 'unsigned long' arguments.
This patch changes all users of IS_ERR_VALUE() that I could find
on 32-bit ARM randconfig builds and x86 allmodconfig. For the
moment, this doesn't change the definition of IS_ERR_VALUE()
because there are probably still architecture specific users
elsewhere.
Almost all the warnings I got are for files that are better off
using 'if (err)' or 'if (err < 0)'.
The only legitimate user I could find that we get a warning for
is the (32-bit only) freescale fman driver, so I did not remove
the IS_ERR_VALUE() there but changed the type to 'unsigned long'.
For 9pfs, I just worked around one user whose calling conventions
are so obscure that I did not dare change the behavior.
I was using this definition for testing:
#define IS_ERR_VALUE(x) ((unsigned long*)NULL == (typeof (x)*)NULL && \
unlikely((unsigned long long)(x) >= (unsigned long long)(typeof(x))-MAX_ERRNO))
which ends up making all 16-bit or wider types work correctly with
the most plausible interpretation of what IS_ERR_VALUE() was supposed
to return according to its users, but also causes a compile-time
warning for any users that do not pass an 'unsigned long' argument.
I suggested this approach earlier this year, but back then we ended
up deciding to just fix the users that are obviously broken. After
the initial warning that caused me to get involved in the discussion
(fs/gfs2/dir.c) showed up again in the mainline kernel, Linus
asked me to send the whole thing again.
[ Updated the 9p parts as per Al Viro - Linus ]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: https://lkml.org/lkml/2016/1/7/363
Link: https://lkml.org/lkml/2016/5/27/486
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> # For nvmem part
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
SSICKR (Gen2) / BRGCKR (Gen3) 31bit mask should be opened,
because BRGB (= for 48kHz) might select it.
Special thanks Yokoyama-san
Reported-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Really sorry about this late pull request. It looks like at the time I
sent my pull request for v4.7 there was some conflict or other issue
which caused my script to stop merging the ASoC branches at some point
after the HDMI changes.
It's all specific driver updates, including:
- New drivers for MAX98371 and TAS5720.
- SPI support for TLV320AIC32x4.
- TDM support for STI Uniperf IPs.
This code should all have been in -next prior to the merge window apart
from some fixes, it dropped out on the 18th.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXSEQkAAoJECTWi3JdVIfQsPoH/jDJ/Eo95aq2UWBqjNbGCahZ
GIiV6TsSnfbg+UIiEvnJUt0ABa0NYKbyOGUny+NC/gLUt4n3FvzGSGGXs/pkuR9R
kF07daPDyQp2uz2GFjN45JLZJV/P1ofkJTsjYnqqqup15XW7EA0F5KbTiOhd+VIc
GlgUHZGMpxVYCc9bS59ZW2V/X1Epzuh8cKD3+I1vyYo6UZbsKMPzhS3aksCM5cMO
h3uifB4hgS26x+0Yrinj0capUalmS+N7isMtL3r/c0Z8DGRiHZOZuMnfoGavNek+
qR/SbOpj2Lj6J9Xut63xtoLAo/JNj7Fk7xYxkOxlpO8+Jqk9KgEKEM/Va3xLJ+M=
=yEWH
-----END PGP SIGNATURE-----
Merge tag 'asoc-v4.7-2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Updates for v4.7 part 2
Really sorry about this late pull request. It looks like at the time I
sent my pull request for v4.7 there was some conflict or other issue
which caused my script to stop merging the ASoC branches at some point
after the HDMI changes.
It's all specific driver updates, including:
- New drivers for MAX98371 and TAS5720.
- SPI support for TLV320AIC32x4.
- TDM support for STI Uniperf IPs.
This code should all have been in -next prior to the merge window apart
from some fixes, it dropped out on the 18th.
The updates this time around are almost all driver code:
- Further slow progress on the topology code.
- Substantial updates and improvements for the da7219, es8328, fsl-ssi
Intel and rcar drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXOao7AAoJECTWi3JdVIfQ3EQH/1Z4nukvcOeZgVN/4K9b27t2
LYSyPH4+7XiDsi24UAyxZWls625t+1XRtolS0yHYY+IMObkeH/T+StTirDG4C1Mv
0uw/lEs5XmkSPFMad2fDcVXhf+D6EsvuLZ24qLKhoi8TyePv6GRvYapitE4dAI7Z
bBwjT+f9r1qSMJvfCmqit8zDneDFMKd7oqPmBW6NpFri5/ksn1KUnd/zOGu2SlSd
R01Oa2VbRDGj8/Zzu5MORvgLLucxTqtAFYeF3T52M5oc33IBWvbha4fk/BDOswbz
H9S3vHyakmbZgXnnGMTp4qz0bxA76YaHzjtqgGUEMbigHTsB0PP5TtII3i5LkaY=
=Zsr1
-----END PGP SIGNATURE-----
Merge tag 'asoc-v4.7' into asoc-linus
ASoC: Updates for v4.7
The updates this time around are almost all driver code:
- Further slow progress on the topology code.
- Substantial updates and improvements for the da7219, es8328, fsl-ssi
Intel and rcar drivers.
# gpg: Signature made Mon 16 May 2016 12:08:43 BST using RSA key ID 5D5487D0
# gpg: Good signature from "Mark Brown <broonie@sirena.org.uk>"
# gpg: aka "Mark Brown <broonie@debian.org>"
# gpg: aka "Mark Brown <broonie@kernel.org>"
# gpg: aka "Mark Brown <broonie@tardis.ed.ac.uk>"
# gpg: aka "Mark Brown <broonie@linaro.org>"
# gpg: aka "Mark Brown <Mark.Brown@linaro.org>"
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 3F25 68AA C269 98F9 E813 A1C5 C3F4 36CA 30F5 D8EB
# Subkey fingerprint: ADE6 68AA 6757 18B5 9FE2 9FEA 24D6 8B72 5D54 87D0
Add the pin configuration value of this machine into the pin_quirk
table to make DELL1_MIC_NO_PRESENCE apply to this machine.
Cc: <stable@vger.kernel.org>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add support for ALC295/ALC3254.
They are simply compatible with ALC225 chip.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
While building m32r allmodconfig the build failed with:
ERROR: "bad_dma_ops" [sound/soc/kirkwood/snd-soc-kirkwood.ko] undefined!
To satisfy the dependency CONFIG_SND_KIRKWOOD_SOC should depend on
HAS_DMA.
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
The headphone has noise when playing sound or switching microphone sources.
It uses the same codec on XPS 13 9350, but with different subsystem ID.
Applying the fixup can solve the issue.
Also, changing the model name to better differentiate models.
v2: Reorder by device ID.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This time was again a relatively calm development cycle; most of
updates are about drivers, and no radical changes are seen in any
core code. Here are some highlights:
ALSA core:
- Continued hardening of ALSA hrtimer
- A few leak fixes in timer interface
- Fix poll error handling in PCM and compress
- Add error propagation in compress API
- Removal of dead rtctimer driver
HD-audio:
- Native ELD notify support for i915 HDMI
- Realtek ALC234 & co support
- Code refactoring to standardize chmap support
- Continued development for SKL HDMI core support
Firewire:
- Apply delayed card registration to all drivers
- Improved / stabilized the handling of PCM stream start / stop
- Add tracepoints to dump a part of isochronous packet data
- Fixed incoming/outgoing packet parameter usages
- Add support for M-Audio profire series
USB-audio:
- Fixes for UAC2 clock source
- SS+ support
- Workaround for oft-seen repeated sample rate read errors
ASoC:
- Further slow progress on the topology code
- Substantial updates and improvements for the da7219, es8328,
fsl-ssi, Intel and rcar drivers.
- Compress error handling in WM ADSP driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABCAAGBQJXPYgvAAoJEGwxgFQ9KSmka3IQAJfXxKYyL0mqOgUpFav2QprE
j4nQFSQf2KMAHgod1iF4Pv5glRZ3T8CbWllu/+GT87ny4wwJH76D07VCZSnrA+cv
NMxRMN8QiGWS+eNPDNqRbcpzQvgwRK17VAmvpIfZtdntq3IryPLyCnY+FJ6Xt5v7
CjgGjlKJQ8i6AJVtoKVlrCOTBPS8YezQ7o67v8+BNrHDyOr0pwLERhvqJBRjaCbj
fKj+JNDsWyu4kX0nInKNGah+5Qiib68+UNK5M+/PnoWv9tEOBPNXeWqRkcRpwnrF
t1BQLnKGdlcSIufXcvxHDdxLftJZ38w+EbnQ/2r+SYHYIwPqTWdvVeXZUiq70wW/
WBUEOHybaHTNc52nMpjo/PU72CHa29zvKq+QHMXMRmFfVrLepIgEpBRBUjENtCjM
3OUn1IhYiNI4FOfgLm5duuYSBVdS4C2qstBDMtGpP64l7AmBZMFtbGUP8pKhvpzF
FR2VoQpBFLPo805lQBKYbxdpzUGqfR7M/O73WRMzB/ZPZa95VNCDoRDQBbYF4Wzy
SByVcE56znxoS9AmbhU6LzCXxdyVp6YAXZNR0pHp+8QdrRoFQZwRhfNVN3FIeNub
COV+0pCQ2GTYvVdfLjdh6VT4shXeg5ZrUVnE3akL+8OzXow9lKyhknvLHn71aTZi
HT0vSirSdrEYf4zg6wtB
=QsAc
-----END PGP SIGNATURE-----
Merge tag 'sound-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"This time was again a relatively calm development cycle; most of
updates are about drivers, and no radical changes are seen in any core
code. Here are some highlights:
ALSA core:
- Continued hardening of ALSA hrtimer
- A few leak fixes in timer interface
- Fix poll error handling in PCM and compress
- Add error propagation in compress API
- Removal of dead rtctimer driver
HD-audio:
- Native ELD notify support for i915 HDMI
- Realtek ALC234 & co support
- Code refactoring to standardize chmap support
- Continued development for SKL HDMI core support
Firewire:
- Apply delayed card registration to all drivers
- Improved / stabilized the handling of PCM stream start / stop
- Add tracepoints to dump a part of isochronous packet data
- Fixed incoming/outgoing packet parameter usages
- Add support for M-Audio profire series
USB-audio:
- Fixes for UAC2 clock source
- SS+ support
- Workaround for oft-seen repeated sample rate read errors
ASoC:
- Further slow progress on the topology code
- Substantial updates and improvements for the da7219, es8328,
fsl-ssi, Intel and rcar drivers.
- Compress error handling in WM ADSP driver"
* tag 'sound-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (177 commits)
ALSA: firewire-lib: change a member of event structure to suppress sparse wanings to bool type
sound: oss: Use setup_timer and mod_timer.
ASoC: hdac_hdmi: Remove the unused 'timeout' variable
ASoC: fsl_ssi: Fix channel slipping on capture (or playback) restart in full duplex.
ASoC: fsl_ssi: Fix channel slipping in Playback at startup
ASoC: fsl_ssi: Fix samples being dropped at Playback startup
ASoC: fsl_ssi: Save a dev reference for dev_err() purpose.
ASoC: fsl_ssi: The IPG/5 limitation concerns the bitclk, not the sysclk.
ASoC: fsl_ssi: Real hardware channels max number is 32
ASoC: pcm5102a: Add support for PCM5102A codec
ASoC: hdac_hdmi: add link management
ASoC: Intel: Skylake: add link management
ALSA: hdac: add link pm and ref counting
ALSA: au88x0: Fix zero clear of stream->resources
ASoC: rt298: Add DMI match for Broxton-P reference platform
ASoC: rt298: fix null deref on acpi driver data
ASoC: dapm: deprecate MICBIAS widget type
ALSA: firewire-lib: drop skip argument from helper functions to queue a packet
ALSA: firewire-lib: add context information to tracepoints
ALSA: firewire-lib: permit to flush queued packets only in process context for better PCM period granularity
...
This time round the update brings in following changes:
- New tegra driver for ADMA device
- Support for Xilinx AXI Direct Memory Access Engine and Xilinx AXI Central
Direct Memory Access Engine and few updates to this driver.
- New cyclic capability to sun6i and few updates.
- Slave-sg support in bcm2835.
- Updates to many drivers like designware, hsu, mv_xor, pxa, edma,
qcom_hidma & bam.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=0Sy7
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-4.7-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
"This time round the update brings in following changes:
- new tegra driver for ADMA device
- support for Xilinx AXI Direct Memory Access Engine and Xilinx AXI
Central Direct Memory Access Engine and few updates to this driver
- new cyclic capability to sun6i and few updates
- slave-sg support in bcm2835
- updates to many drivers like designware, hsu, mv_xor, pxa, edma,
qcom_hidma & bam"
* tag 'dmaengine-4.7-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (84 commits)
dmaengine: ioatdma: disable relaxed ordering for ioatdma
dmaengine: of_dma: approximate an average distribution
dmaengine: core: Use IS_ENABLED() instead of checking for built-in or module
dmaengine: edma: Re-evaluate errors when ccerr is triggered w/o error event
dmaengine: qcom_hidma: add support for object hierarchy
dmaengine: qcom_hidma: add debugfs hooks
dmaengine: qcom_hidma: implement lower level hardware interface
dmaengine: vdma: Add clock support
Documentation: DT: vdma: Add clock support for dmas
dmaengine: vdma: Add config structure to differentiate dmas
MAINTAINERS: Update Tegra DMA maintainers
dmaengine: tegra-adma: Add support for Tegra210 ADMA
Documentation: DT: Add binding documentation for NVIDIA ADMA
dmaengine: vdma: Add Support for Xilinx AXI Central Direct Memory Access Engine
Documentation: DT: vdma: update binding doc for AXI CDMA
dmaengine: vdma: Add Support for Xilinx AXI Direct Memory Access Engine
Documentation: DT: vdma: update binding doc for AXI DMA
dmaengine: vdma: Rename xilinx_vdma_ prefix to xilinx_dma
dmaengine: slave means at least one of DMA_SLAVE, DMA_CYCLIC
dmaengine: mv_xor: Allow selecting mv_xor for mvebu only compatible SoC
...
The ak4642 driver is using a regmap cache sync to restore the
configuration of the chip on resume but (as Peter observed) does not
actually define a register cache which means that the resume is never
going to work and we trigger asserts in regmap. Fix this by enabling
caching.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reported-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Disconnect also the path to AUXL from the HF path during digital_mute to
avoid pop noise leakage to Line-out pads.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit a9c4284bf5 ("ALSA: firewire-lib: add context information to
tracepoints") adds new members to tracepoint events of this module, to
represent context information. One of the members is bool type and
this causes sparse warnings.
16:1: warning: expression using sizeof bool
60:1: warning: expression using sizeof bool
16:1: warning: odd constant _Bool cast (ffffffffffffffff becomes 1)
60:1: warning: odd constant _Bool cast (ffffffffffffffff becomes 1)
This commit suppresses the warnings, by changing type of the member
to 'unsigned int'. Additionally, this commit applies '!!' idiom to
get 0/1 from 'in_interrupt()'.
Fixes: a9c4284bf5 ("ALSA: firewire-lib: add context information to tracepoints")
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Core infrastructural changes:
- Support for natively single-ended GPIO driver stages. This
means that if the hardware has registers to configure open
drain or open source configuration, we use that rather than
(as we did before) try to emulate it by switching the line
to an input to get high impedance. This is also documented
throughly in Documentation/gpio/driver.txt for those of you
who did not understand one word of what I just wrote.
- Start to do away with the unnecessarily complex and
unitelligible ARCH_REQUIRE_GPIOLIB and
ARCH_WANT_OPTIONAL_GPIOLIB, another evolutional artifact from
the time when the GPIO subsystem was unmaintained. Archs can
now just select GPIOLIB and be done with it, cleanups to
arches will trickle in for the next kernel. Some minor archs
ACKed the changes immediately so these are included in this
pull request.
- Advancing the use of the data pointer inside the GPIO device
for storing driver data by switching the PowerPC, Super-H
Unicore and a few other subarches or subsystem drivers in
ALSA SoC, Input, serial, SSB, staging etc to use it.
- The initialization now reads the input/output state of the
GPIO lines, so that each GPIO descriptor knows - if this
callback is implemented - whether the line is input or
output. This also reflects nicely in userspace "lsgpio".
- It is now possible to name GPIO producer names, line names,
from the device tree. (Platform data has been supported for
a while.) I bet we will get a similar mechanism for ACPI
one of those days. This makes is possible to get sensible
producer names for e.g. GPIO rails in "lsgpio" in userspace.
New drivers:
- New driver for the Loongson1.
- The XLP driver now supports Broadcom Vulcan ARM64.
- The IT87 driver now supports IT8620 and IT8628.
- The PCA953X driver now supports Galileo Gen2.
Driver improvements:
- MCP23S08 was switched to use the gpiolib irqchip helpers and
now also suppors level-triggered interrupts.
- 74x164 and RCAR now supports the .set_multiple() callback
- AMDPT was converted to use generic GPIO.
- TC3589x, TPS65218, SX150X, F7188X, MENZ127, VX855, WM831X, WM8994
support the new single ended callback for open drain
and in some cases open source.
- Implement the .get_direction() callback for a few more drivers
like PL061, Xgene.
Cleanups:
- Paul Gortmaker combed through the drivers and de-modularized
those who are not really modules.
- Move the GPIO poweroff DT bindings to the power subdir where
they belong.
- Rename gpio-generic.c to gpio-mmio.c, which is much more to the
point. That's what it is handling, nothing more, nothing less.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=z4d6
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for kernel cycle v4.7:
Core infrastructural changes:
- Support for natively single-ended GPIO driver stages.
This means that if the hardware has registers to configure open
drain or open source configuration, we use that rather than (as we
did before) try to emulate it by switching the line to an input to
get high impedance.
This is also documented throughly in Documentation/gpio/driver.txt
for those of you who did not understand one word of what I just
wrote.
- Start to do away with the unnecessarily complex and unitelligible
ARCH_REQUIRE_GPIOLIB and ARCH_WANT_OPTIONAL_GPIOLIB, another
evolutional artifact from the time when the GPIO subsystem was
unmaintained.
Archs can now just select GPIOLIB and be done with it, cleanups to
arches will trickle in for the next kernel. Some minor archs ACKed
the changes immediately so these are included in this pull request.
- Advancing the use of the data pointer inside the GPIO device for
storing driver data by switching the PowerPC, Super-H Unicore and
a few other subarches or subsystem drivers in ALSA SoC, Input,
serial, SSB, staging etc to use it.
- The initialization now reads the input/output state of the GPIO
lines, so that each GPIO descriptor knows - if this callback is
implemented - whether the line is input or output. This also
reflects nicely in userspace "lsgpio".
- It is now possible to name GPIO producer names, line names, from
the device tree. (Platform data has been supported for a while).
I bet we will get a similar mechanism for ACPI one of those days.
This makes is possible to get sensible producer names for e.g.
GPIO rails in "lsgpio" in userspace.
New drivers:
- New driver for the Loongson1.
- The XLP driver now supports Broadcom Vulcan ARM64.
- The IT87 driver now supports IT8620 and IT8628.
- The PCA953X driver now supports Galileo Gen2.
Driver improvements:
- MCP23S08 was switched to use the gpiolib irqchip helpers and now
also suppors level-triggered interrupts.
- 74x164 and RCAR now supports the .set_multiple() callback
- AMDPT was converted to use generic GPIO.
- TC3589x, TPS65218, SX150X, F7188X, MENZ127, VX855, WM831X, WM8994
support the new single ended callback for open drain and in some
cases open source.
- Implement the .get_direction() callback for a few more drivers like
PL061, Xgene.
Cleanups:
- Paul Gortmaker combed through the drivers and de-modularized those
who are not really modules.
- Move the GPIO poweroff DT bindings to the power subdir where they
belong.
- Rename gpio-generic.c to gpio-mmio.c, which is much more to the
point. That's what it is handling, nothing more, nothing less"
* tag 'gpio-v4.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (126 commits)
MIPS: do away with ARCH_[WANT_OPTIONAL|REQUIRE]_GPIOLIB
gpio: zevio: make it explicitly non-modular
gpio: timberdale: make it explicitly non-modular
gpio: stmpe: make it explicitly non-modular
gpio: sodaville: make it explicitly non-modular
pinctrl: sh-pfc: Let gpio_chip.to_irq() return zero on error
gpio: dwapb: Add ACPI device ID for DWAPB GPIO controller on X-Gene platforms
gpio: dt-bindings: add wd,mbl-gpio bindings
gpio: of: make it possible to name GPIO lines
gpio: make gpiod_to_irq() return negative for NO_IRQ
gpio: xgene: implement .get_direction()
gpio: xgene: Enable ACPI support for X-Gene GFC GPIO driver
gpio: tegra: Implement gpio_get_direction callback
gpio: set up initial state from .get_direction()
gpio: rename gpio-generic.c into gpio-mmio.c
gpio: generic: fix GPIO_GENERIC_PLATFORM is set to module case
gpio: dwapb: add gpio-signaled acpi event support
gpio: dwapb: convert device node to fwnode
gpio: dwapb: remove name from dwapb_port_property
gpio/qoriq: select IRQ_DOMAIN
...
The function setup_timer combines the initialization of a timer with the
initialization of the timer's function and data fields. The mulitiline
code for timer initialization is now replaced with function setup_timer.
Also, quoting the mod_timer() function comment:
-> mod_timer() is a more efficient way to update the expire field of an
active timer (if the timer is inactive it will be activated).
Use setup_timer() and mod_timer() to setup and arm a timer, making the
code compact and aid readablity.
Signed-off-by: Muhammad Falak R Wani <falakreyaz@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix an unused variable warning in the HDAC code.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXOvOkAAoJECTWi3JdVIfQncoH/3BboOa665tefIeEceyB5B9y
UsavcXz9v8EDSqt1Kwv34dkoiDS7cCO8ds/EpNrJkwQRv3dTtelI0KnbHrFo521G
7sFsVc98LpNvWanIKHo+KKfEiJdoOrgK3k0Jzc/9xXBK26ExdfRnnK0fdyVyfLug
1jXGKbbWvhIHLOaGz41aQ4QeYy6prq115LewsCziidY6w/Y20SuT2UzRzHbqsIk/
9RGSyzFknrOJDM5hM2trDp0Z3l2lX+4jP0RYkRtMNspg38Ig5zK/w/adLOLXzVpY
hqBr1rfVIbgXCQ2Ha2TgjPjvRj4vDmpvqPLerQxI8HiknL9bc5uN1CZV8Hh/F7E=
=vvzR
-----END PGP SIGNATURE-----
Merge tag 'asoc-v4.7-fix-hdac' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fix for v4.7
Fix an unused variable warning in the HDAC code.
- In-kernel ACPICA code update to the upstream release 20160422
adding support for ACPI 6.1 along with some previously missing
bits of ACPI 6.0 support, making a fair amount of fixes and
cleanups and reducing divergences between the upstream ACPICA
and the in-kernel code (Bob Moore, Lv Zheng, Al Stone, Aleksey
Makarov, Will Miles).
- ACPI Generic Event Device (GED) support and a fix for it (Sinan Kaya,
Paul Gortmaker).
- INT3406 thermal driver for display thermal management and ACPI
backlight support code reorganization related to it (Aaron Lu,
Arnd Bergmann).
- Support for exporting the value returned by the _HRV (hardware
revision) ACPI object via sysfs (Betty Dall).
- Removal of the EXPERT dependency for ACPI on ARM64 (Mark Brown).
- Rework of the handling of ACPI _OSI mechanism allowing the
_OSI("Darwin") support to be overridden from the kernel command
line among other things (Lv Zheng, Chen Yu).
- Rework of the ACPI tables override mechanism to prepare it for
the introduction of overlays support going forward (Lv Zheng,
Rafael Wysocki).
- Fixes related to the ECDT support and module-level execution
of AML (Lv Zheng).
- ACPI PCI interrupts management update to make it work better on
ARM64 mostly (Sinan Kaya).
- ACPI SRAT handling update to make the code process all entires
in the table order regardless of the entry type (Lukasz Anaczkowski).
- EFI power off support for full-hardware ACPI platforms that don't
support ACPI S5 (Chen Yu).
- Fixes and cleanups related to the ACPI core's sysfs interface
(Dan Carpenter, Betty Dall).
- acpi_dev_present() API rework to reduce possible confusion related
to it (Lukas Wunner).
- Removal of CLK_IS_ROOT from two ACPI drivers (Stephen Boyd).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=rAwm
-----END PGP SIGNATURE-----
Merge tag 'acpi-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI updates from Rafael Wysocki:
"The new features here are ACPI 6.1 support (and some previously
missing bits of ACPI 6.0 support) in ACPICA and two new drivers, a
driver for the ACPI Generic Event Device (GED) feature introduced by
ACPI 6.1 and the INT3406 thermal driver for display thermal
management. Also the value returned by the _HRV (hardware revision)
ACPI object will be exported to user space via sysfs now.
In addition to that, ACPI on ARM64 will not depend on EXPERT any more.
The rest is mostly fixes and cleanups and some code reorganization.
Specifics:
- In-kernel ACPICA code update to the upstream release 20160422
adding support for ACPI 6.1 along with some previously missing bits
of ACPI 6.0 support, making a fair amount of fixes and cleanups and
reducing divergences between the upstream ACPICA and the in-kernel
code (Bob Moore, Lv Zheng, Al Stone, Aleksey Makarov, Will Miles)
- ACPI Generic Event Device (GED) support and a fix for it (Sinan
Kaya, Paul Gortmaker)
- INT3406 thermal driver for display thermal management and ACPI
backlight support code reorganization related to it (Aaron Lu, Arnd
Bergmann)
- Support for exporting the value returned by the _HRV (hardware
revision) ACPI object via sysfs (Betty Dall)
- Removal of the EXPERT dependency for ACPI on ARM64 (Mark Brown)
- Rework of the handling of ACPI _OSI mechanism allowing the
_OSI("Darwin") support to be overridden from the kernel command
line among other things (Lv Zheng, Chen Yu)
- Rework of the ACPI tables override mechanism to prepare it for the
introduction of overlays support going forward (Lv Zheng, Rafael
Wysocki)
- Fixes related to the ECDT support and module-level execution of AML
(Lv Zheng)
- ACPI PCI interrupts management update to make it work better on
ARM64 mostly (Sinan Kaya)
- ACPI SRAT handling update to make the code process all entires in
the table order regardless of the entry type (Lukasz Anaczkowski)
- EFI power off support for full-hardware ACPI platforms that don't
support ACPI S5 (Chen Yu)
- Fixes and cleanups related to the ACPI core's sysfs interface (Dan
Carpenter, Betty Dall)
- acpi_dev_present() API rework to reduce possible confusion related
to it (Lukas Wunner)
- Removal of CLK_IS_ROOT from two ACPI drivers (Stephen Boyd)"
* tag 'acpi-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (82 commits)
ACPI / video: mark acpi_video_get_levels() inline
Thermal / ACPI / video: add INT3406 thermal driver
ACPI / GED: make evged.c explicitly non-modular
ACPI / tables: Fix DSDT override mechanism
ACPI / sysfs: fix error code in get_status()
ACPICA: Update version to 20160422
ACPICA: Move all ASCII utilities to a common file
ACPICA: ACPI 2.0, Hardware: Add access_width/bit_offset support for acpi_hw_write()
ACPICA: ACPI 2.0, Hardware: Add access_width/bit_offset support in acpi_hw_read()
ACPICA: Executer: Introduce a set of macros to handle bit width mask generation
ACPICA: Hardware: Add optimized access bit width support
ACPICA: Utilities: Add ACPI_IS_ALIGNED() macro
ACPICA: Renamed some #defined flag constants for clarity
ACPICA: ACPI 6.0, tools/iasl: Add support for new resource descriptors
ACPICA: ACPI 6.0: Update _BIX support for new package element
ACPICA: ACPI 6.1: Support for new PCCT subtable
ACPICA: Refactor evaluate_object to reduce nesting
ACPICA: Divergence: remove unwanted spaces for typedef
ACPI,PCI,IRQ: remove SCI penalize function
ACPI,PCI,IRQ: remove redundant code in acpi_irq_penalty_init()
..
* acpi-pci:
ACPI,PCI,IRQ: remove SCI penalize function
ACPI,PCI,IRQ: remove redundant code in acpi_irq_penalty_init()
ACPI,PCI,IRQ: reduce static IRQ array size to 16
ACPI,PCI,IRQ: reduce resource requirements
* acpi-misc:
ACPI / sysfs: fix error code in get_status()
ACPI / device_sysfs: Clean up checkpatch errors
ACPI / device_sysfs: Change _SUN and _STA show functions error return to EIO
ACPI / device_sysfs: Add sysfs support for _HRV hardware revision
arm64: defconfig: Enable ACPI
ACPI / ARM64: Remove EXPERT dependency for ACPI on ARM64
ACPI / ARM64: Don't enable ACPI by default on ARM64
acer-wmi: Use acpi_dev_found()
eeepc-wmi: Use acpi_dev_found()
ACPI / utils: Rename acpi_dev_present()
* acpi-tools:
tools/power/acpi: close file only if it is open
The updates this time around are almost all driver code:
- Further slow progress on the topology code.
- Substantial updates and improvements for the da7219, es8328, fsl-ssi
Intel and rcar drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXOao7AAoJECTWi3JdVIfQ3EQH/1Z4nukvcOeZgVN/4K9b27t2
LYSyPH4+7XiDsi24UAyxZWls625t+1XRtolS0yHYY+IMObkeH/T+StTirDG4C1Mv
0uw/lEs5XmkSPFMad2fDcVXhf+D6EsvuLZ24qLKhoi8TyePv6GRvYapitE4dAI7Z
bBwjT+f9r1qSMJvfCmqit8zDneDFMKd7oqPmBW6NpFri5/ksn1KUnd/zOGu2SlSd
R01Oa2VbRDGj8/Zzu5MORvgLLucxTqtAFYeF3T52M5oc33IBWvbha4fk/BDOswbz
H9S3vHyakmbZgXnnGMTp4qz0bxA76YaHzjtqgGUEMbigHTsB0PP5TtII3i5LkaY=
=Zsr1
-----END PGP SIGNATURE-----
Merge tag 'asoc-v4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Updates for v4.7
The updates this time around are almost all driver code:
- Further slow progress on the topology code.
- Substantial updates and improvements for the da7219, es8328, fsl-ssi
Intel and rcar drivers.
Happened when the Playback (or Capture) is running continuously
and Capture (or Playback) is restarted (xrun, manual stop/start...)
Since the RX (or TX) FIFO are only reset when the whole SSI is disabled,
pending samples from previous capture (or playback) session may still
be present. They must be erased to not introduce channel slipping.
FIFO Clear register fields are documented in IMX51, IMX35 reference manual.
They are not documented in IMX50 or IMX6 RM, despite they are
working as expected on IMX6SL and IMX6solo.
Signed-off-by: Arnaud Mouiche <arnaud.mouiche@invoxia.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Caleb Crome <caleb@crome.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Previously, SCR.SSIEN and SCR.TE were enabled at once if no capture
stream was also running.
This may not give a chance for the DMA to write the first sample in
TX FIFO before the streaming starts on the PCM bus, inserting void
samples first.
Those void samples are then responsible for slipping the channels.
Signed-off-by: Arnaud Mouiche <arnaud.mouiche@invoxia.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Caleb Crome <caleb@crome.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
If the capture is already running while playback is started, it is highly
probable (>80% in a 8 channels scenario) that samples are lost between
the DMA and TX fifo.
The reason is that SIER.TDMAE is set before STCR.TFEN0, leaving a time
window where the FIFO doesn't receive the samples written by the DMA.
This particular case happened only if capture is already enabled as
SCR.SSIEN is already set at the playback startup instant.
Signed-off-by: Arnaud Mouiche <arnaud.mouiche@invoxia.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Caleb Crome <caleb@crome.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Most of functions only receive the ssi_private reference and don't have
a knowledge of 'dev' pointer, even for debug purpose.
Signed-off-by: Arnaud Mouiche <arnaud.mouiche@invoxia.com>
Tested-by: Caleb Crome <caleb@crome.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
im6sl reference manual 47.7.4:
"
Bit clock - Used to serially clock the data bits in and out of the SSI port.
This clock is either generated internally (from SSI's sys clock) or taken
from external clock source (through the Tx/Rx clock ports).
[...]
Care should be taken to ensure that the bit clock frequency (either
internally generated by dividing the SSI's sys clock or sourced from
external device through Tx/Rx clock ports) is never greater than 1/5
of the ipg_clk (from CCM) frequency.
"
Since, in master mode, the sysclk is a multiple of bitclk, we can
easily reach a high sysclk value, whereas keeping a reasonable bitclk.
ex: 8ch x 16bit x 48kHz = 6144000, requires a 24576000 sysclk (PM=1)
yet ipg_clk/5 = 66Mhz/5 = 13.2
Signed-off-by: Arnaud Mouiche <arnaud.mouiche@invoxia.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Caleb Crome <caleb@crome.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The max number of slots in TDM mode is 32:
- Frame Rate Divider Control is a 5bit value
- Time slot mask registers control 32 slots.
Signed-off-by: Arnaud Mouiche <arnaud.mouiche@invoxia.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Caleb Crome <caleb@crome.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The TLV320AIC32x4 has a very flexible mixer on the inputs to the ADCs. Each
mixer has an available set of available pins that can be connected to the
ADC positive and negative pins via three different resistor values. This
allows for configuration of differential inputs as well as doing level
manipulation between sources going into the mixers.
The current code only provides positive pins and I implemented the resistors
in an earlier patch. It turns out that it appears to more accurately model
what's happening to implement each of the pins as a MUX rather than on/off
switches and a mixer. This way each pin can be set to its desired resistor
value. Since there are no switches, the mixer is no longer necessary in the
DAPM path. I set the DAPM paths such that the "off" position of any of the
MUXes turns the path off.
This should allow for any input confiuration available on the codec.
Signed-off-by: Jeremy McDermond <nh6z@nh6z.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some definitions to support the PCM5102A codec
by Texas Instruments.
Signed-off-by: Florian Meier <florian.meier@koalo.de>
Changes to original patch by Florian Meier:
* rebased (Makefile and Kconfig
* fixed checkpath errors (spaces, newlines)
* added dt-binding documentation
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Manage the hda idisp link using shiny new link APIs. We need to
keep link On while we probe and also hold the reference in runtime
resume and drop in suspend
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use shiny new link APIs to manage the links. Also remove old link
configuration logic from driver.
We need to keep link and cmd dma to off during active suspend
to allow system to enter low power state and turn it on if
the link and cmd dma was on before active suspend in active
resume.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The HDA links can be switched off when not is use, similarly
command DMA can be stopped as well. This calls for a reference
counting mechanism on the link by it's users to manage the link
power. The DMA can be turned off when all links are off
For this we add two APIs
snd_hdac_ext_bus_link_get
snd_hdac_ext_bus_link_put
They help users to turn up/down link and manage the DMA as well
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
There are a few calls of memset() to stream->resources, but they all
are called in a wrong size, sizeof(unsigned char) * VORTEX_RESOURCE_LAST,
while this field is a u32 array. This may leave the memories not
zero-cleared.
Fix it by replacing them with a simpler sizeof(stream->resources)
instead.
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The current device tree representation of the R-Car Sample Rate Converters
(SRC) assumes that they are numbered consecutively, starting from 0. Alas,
this is not the case with the R8A7794 SoC where SRC0 isn't present. In
order to keep the existing device trees working, I'm suggesting to use a
disabled node for SRC0. Teach the SRC probe to just skip disabled nodes.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Broxton-P reference platform also uses combo jack for audio
connector so we need to set codec pdata to use this based on DMI
match for this board.
Signed-off-by: Ramesh Babu <ramesh.babu@intel.com>
Signed-off-by: Senthilnathan Veppur <senthilnathanx.veppur@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Acked-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ACPI driver data can be NULL so we need to check that before
dereference the driver data.
Signed-off-by: Senthilnathan Veppur <senthilnathanx.veppur@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Acked-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
On most of audio and music units on IEEE 1394 bus which ALSA firewire stack
supports (or plans to support), CIP with two quadlets header is used.
Thus, there's no cases to queue packets with blank payload. If such packets
are going to be queued, it means that they're for skips of the cycle.
This commit simplifies helper functions to queue a packet.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In current implementation, packet processing is done in both of software
IRQ contexts of IR/IT contexts and process contexts.
This is usual interrupt handling of IR/IT context for 1394 OHCI.
(in hardware IRQ context)
irq_handler() (drivers/firewire/ohci.c)
->tasklet_schedule()
(in software IRQ context)
handle_it_packet() or handle_ir_packet_per_buffer() (drivers/firewire/ohci.c)
->flush_iso_completions()
->struct fw_iso_context.callback.sc()
= out_stream_callback() or in_stream_callback()
However, we have another chance for packet processing. It's done in PCM
frame handling via ALSA PCM interfaces.
(in process context)
ioctl(i.e. SNDRV_PCM_IOCTL_HWSYNC)
->snd_pcm_hwsync() (sound/core/pcm_native.c)
->snd_pcm_update_hw_ptr() (sound/core/pcm_lib.c)
->snd_pcm_update_hw_ptr0()
->struct snd_pcm_ops.pointer()
= amdtp_stream_pcm_pointer()
->fw_iso_context_flush_completions() (drivers/firewire/core-iso.c)
->struct fw_card_driver.flush_iso_completions()
= ohci_flush_iso_completions() (drivers/firewire/ohci.c)
->flush_iso_completions()
->struct fw_iso_context.callback.sc()
= out_stream_callback() or in_stream_callback()
This design is for a better granularity of PCM pointer. When ioctl(2) is
executed with some commands for ALSA PCM interface, queued packets are
handled at first. Then, the latest number of handled PCM frames is
reported. The number can represent PCM frames transferred in most near
isochronous cycle.
Current tracepoints include no information to distinguish running contexts.
When tracing the interval of software IRQ context, this is not good.
This commit adds more information for current context. Additionally, the
index of packet processed in one context is added in a case that packet
processing is executed in continuous context of the same kind,
As a result, the output includes 11 fields with additional two fields
to commit 0c95c1d619 ("ALSA: firewire-lib: add tracepoints to dump a part
of isochronous packet data"):
17131.9186: out_packet: 07 7494 ffc0 ffc1 00 000700c0 9001a496 058 45 1 13
17131.9186: out_packet: 07 7495 ffc0 ffc1 00 000700c8 9001ba00 058 46 1 14
17131.9186: out_packet: 07 7496 ffc0 ffc1 00 000700d0 9001ffff 002 47 1 15
17131.9189: out_packet: 07 7497 ffc0 ffc1 00 000700d0 9001d36a 058 00 0 00
17131.9189: out_packet: 07 7498 ffc0 ffc1 00 000700d8 9001e8d4 058 01 0 01
17131.9189: out_packet: 07 7499 ffc0 ffc1 00 000700e0 9001023e 058 02 0 00
17131.9206: in_packet: 07 7447 ffc1 ffc0 01 3f070072 9001783d 058 32 1 00
17131.9206: in_packet: 07 7448 ffc1 ffc0 01 3f070072 90ffffff 002 33 1 01
17131.9206: in_packet: 07 7449 ffc1 ffc0 01 3f07007a 900191a8 058 34 1 02
(Here, some common fields are omitted so that a line is within 80
characters.)
The legend is:
- The second of cycle scheduled for the packet
- The count of cycle scheduled for the packet
- The ID of node as source (hex)
- The ID of node as destination (hex)
- The value of isochronous channel
- The first quadlet of CIP header (hex)
- The second quadlet of CIP header (hex)
- The number of included quadlets
- The index of packet in a buffer maintained by this module
- 0 in process context, 1 in IRQ context
- The index of packet processed in the context
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
These three commits were merged to improve PCM pointer granularity.
commit 76fb878948 ("ALSA: firewire-lib: taskletize the snd_pcm_period_elapsed() call")
commit e9148dddc3 ("ALSA: firewire-lib: flush completed packets when reading PCM position")
commit 92b862c7d6 ("ALSA: firewire-lib: optimize packet flushing")
The point of them is to handle queued packets not only in software IRQ
context of IR/IT contexts, but also in process context. As a result of
handling packets, period tasklet is scheduled when acrossing PCM period
boundary. This is to prevent recursive call of
'struct snd_pcm_ops.pointer()' in the same context.
When the pointer callback is executed in the process context, it's
better to avoid the second callback in the software IRQ context. The
software IRQ context runs immediately after scheduled in the process
context because few packets are queued yet.
For the aim, 'pointer_flush' is used, however it causes a race condition
between the process context and software IRQ context of IR/IT contexts.
Practically, this race is not so critical because it influences process
context to skip flushing queued packet and to get worse granularity of
PCM pointer. The race condition is quite rare but it should be improved
for stable service.
The similar effect can be achieved by using 'in_interrupt()' macro. This
commit obsoletes 'pointer_flush' with it.
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Phoenix Audio has yet another device with another id (even a different
vendor id, 0556:0014) that requires the same quirk for the sample
rate.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=110221
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Format number after 0x in hex.
Cc: Jie Yang <yang.jie@linux.intel.com>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When the codec is in standby we do not need to keep the HPPLL active.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The HDMI/DP audio output on ATI/AMD chips got broken due to the recent
restructuring of chmap. Fortunately, Daniel Exner could bisect, and
pointed the culprit commit [739ffee97e: ALSA: hda - Add hdmi chmap
verb programming ops to chmap object].
This commit moved some ops from hdmi_ops to chmap_ops, and reassigned
the ops in the embedded chmap object in hdmi_spec instead.
Unfortunately, the reassignment of these ops in patch_atihdmi() were
moved into an if block that is performed only for old chips. Thus, on
newer chips, the generic ops is still used, which doesn't work for
such ATI/AMD chips.
This patch addresses the regression, simply by moving the assignment
of chmap ops to the right place.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=114981
Fixes: 739ffee97e ('ALSA: hda - Add hdmi chmap verb programming ops to chmap object')
Reported-and-tested-by: Daniel Exner <dex@dragonslave.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Current checking for PLL 32KHz mode fails in driver code when
bypassing the PLL. This is due to an incorrect check of PLL
source type when 32KHz clock is provided. Removal of this check
resolves the issue.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This update changes the dividers used for ranges of input MCLK
frequencies, to improve PLL locking for a corner case when at edge
of MCLK frequency input divider range.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently PC counter is always synchronised to DAI which means that
when the DAI is disabled, features such as ALC calibration cannot
be executed successfully. This patch makes sure that when the DAI
is disabled, PC counter is set to free-running.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When the codec is DAI clk slave, and the SRM feature of the PLL
is being used, the enabling of the DAI should occur only after
the PLL has locked to the incoming WCLK. This update adds checking
to the the DAI widget event, so it waits for SRM to lock. There is
also a timeout if that lock doesn't occur within a given time.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently, when Codec is I2S master DAI clocks are continuously
generated even if all audio streams have stopped. To improve
efficiency, control of the DAI clocks for master mode have been
moved to a DAPM widget event so they're only enabled as required.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds the Broxton-P machine driver for Intel Broxton-P
reference boards. This machine uses the RT298 codec
Signed-off-by: Ramesh Babu <ramesh.babu@intel.com>
Signed-off-by: Senthilnathan Veppur <senthilnathanx.veppur@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Broxton-P platform has 6 SSPs so we need to add ssp2 thru
ssp5 to DAI list for the driver.
Signed-off-by: Pardha Saradhi K <pardha.saradhi.kesapragada@intel.com>
Signed-off-by: Ramesh Babu <ramesh.babu@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd_dmapp_get_id() returns 0xFF as error code if system used
strange connection. It will be used as PDMACHCRn.SRS, but 0xFF is
prohibited number.
In order not to use prohibited number, this patch indicates error message
and returns 0x00 (same as SSI00) in error case.
Special thanks to Dung-san.
Reported-by: Nguyen Viet Dung <nv-dung@jinso.co.jp>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Although the ES8328 does support different rates for capture and
playback, only very limited combinations are supported (8kHz and 48kHz
or 8.0182kHz and 44.1kHz) with most rates required to be symmetric.
Instead of adding a lot of complexity for little gain, let's enforce
symmetric rates.
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The values are the same for the DAC and ADC so remove the specific
values and use values with shifts.
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is a refactor in preparation for supporting more sample sizes which
has no functional change.
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is always used along with ES8328_CONTROL1_ENREF so there is no
change in the generated code as a result of this fix.
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The ADCCONTROL4 and DACCONTROL1 registers are similar but not identical,
with the DACCONTROL1 having each field starting one bit higher than
ADCCONTROL4.
Instead of introducing a magic shift, add new constants for the values
in ADCCONTROL4 and use a second variable to setup the ADC.
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This ensures that the clock is setup after its frequency has been set;
the existing code in set_dai_fmt may be called before the clock rate has
been set resulting in an incorrect configuration.
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When snd_pcm_add_chmap_ctls() is called to the PCM stream to which a
chmap has been already assigned, it returns as an error due to the
conflicting snd_ctl_add() result. However, this also clears the
already assigned chmap_kctl field via pcm_chmap_ctl_private_free(),
and becomes inconsistent in the later operation.
This patch adds the check of the conflicting chmap kctl before
actually trying to allocate / assign. The check failure is treated as
a kernel warning, as the double call of snd_pcm_add_chmap_ctls() is
basically a driver bug and having the stack trace would help
developers to figure out the bad code path.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In former commit, drivers in ALSA firewire stack always starts IT context
before IR context. If IR context starts after packets are transmitted by
peer unit, packet discontinuity may be detected because the context starts
in the middle of packet streaming. This situation is rare because IT
context usually starts immediately. However, it's better to solve this
issue. This is suppressed with CIP_SKIP_INIT_DBC_CHECK flag.
This commit enables the same feature as CIP_SKIP_INIT_DBC_CHECK.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In previous commit, this module has no need to reuse parameters of
incoming packets for outgoing packets anymore. This commit arranges some
needless codes for outgoing packet processing.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In previous commit, this module has no need to reuse parameters of
incoming packets for outgoing packets anymore. This commit arranges some
needless codes for incoming packet processing.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In clause 6.3 of IEC 61883-6:2000, there's an explanation about processing
of presentation timestamp. In the clause, we can see "If a function block
receives a CIP, processes it and subsequently re-transmits it, then the
SYT of the outgoing CIP shall be the sum of the incoming SYT and the
processing delay." ALSA firewire stack has an implementation to partly
satisfy this specification. Developers assumed the stack to perform as an
Audio function block[1].
Following to the assumption, current implementation of ALSA firewire stack
use one software interrupt context to handle both of in/out packets. In
most case, this is processed in 1394 OHCI IR context independently of the
opposite context. Thus, this implementation uses longer CPU time in the
software interrupt context. This is not better for whole system.
Against the assumption, I confirmed that each ASIC for IEC 61883-1/6
doesn't necessarily expect it to the stack. Thus, current implementation
of ALSA firewire stack includes over-engineering.
This commit purges the implementation. As a result, packets of one
direction are handled in one software interrupt context and spends
minimum CPU time.
[1] [alsa-devel] [PATCH 0/8] [RFC] new driver for Echo Audio's Fireworks based devices
http://mailman.alsa-project.org/pipermail/alsa-devel/2013-June/062660.html
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In packet streaming protocol applied to TASCAM FireWire series, the value
of SYT field in CIP header is always zero, therefore it has no meaning.
There's no need to synchronize packets in both direction for the series.
In current implementation of ALSA firewire stack, driver for the series
uses incoming packet parameter for outgoing packet parameter to calculate
the number of data blocks. This can be simplified because the task of
corresponding driver is to transfer data blocks enough to sampling transfer
frequency.
This commit purges support of full duplex synchronization to prevent
over-engineering implementation.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On Fireworks board module of Echo Audio, TSB43Cx43A (IceLynx Micro, iCEM)
is used to process payload of isochronous packets. There's an public
document of this chip[1]. This document is for firmware programmers to
transfer/receive AMDTP with IEC60958 data format, however in clause 2.5,
2.6 and 2.7, we can see system design to utilize the sequence of value in
SYT field of CIP header. In clause 2.3, we can see the specification of
Audio Master Clock (MCLK) from iCEM.
Well, this clock is actually not used for sampling clock. This can be
confirmed when corresponding driver transfer random value as the sequence
of SYT field. Even if in this case, the unit generates proper sound.
Additionally, in unique command set for this board module, the format
of CIP is changed; for IEC 61883-6 mode which we use, and for Windows
Operating System. In the latter mode, the whole 32 bit field in second CIP
header from Windows driver is used to represent counter of packets (NO-DATA
code is still used for packets without data blocks). If the master clock
was physically used by DSP on the board module, the Windows driver must
have transferred correct sequence of SYT field.
Furthermore, as long as seeing capacities of AudioFire2, AudioFire4,
AudioFire8, AudioFirePre8 and AudioFire12, these models don't support
SYT-Match clock source.
Summary, we have no need to relate incoming/outgoing packets. This commit
drops reusing SYT sequence of incoming packets for outgoing packets.
[1] Using TSB43Cx43A: S/PDIF over 1394 (2003, Texus Instruments
Incorporated)
http://www.ti.com/analog/docs/litabsmultiplefilelist.tsp?literatureNumber=slla148&docCategoryId=1&familyId=361
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Windows driver for BeBoB-based models mostly wait for transmitted packets,
then transfer packets to the models. This looks for the relationship
between incoming packets and outgoing packets to synchronize the sequence
of presentation timestamp.
However, the sequence between packets of both direction has no
relationship. Even if receiving NO-DATA packets, the drivers transfer
packets with meaningful value in SYT field. Additionally, the order of
starting packets is always the same, independently of the source of clock.
The corresponding driver is expected as a generator of presentation
timestamp and these models can select it as a source of sampling clock.
This commit drops reusing SYT sequence from ALSA bebob driver. The driver
always transfer packets with presentation timestamp generated by ALSA
firewire stack, without re-using the sequence of value in SYT field in
incoming packets to outgoing packets.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
