Set cmn_refclk_dig_div/cmn_refclk1_dig_div frequency to 25MHz
as specified in "Common Module Clock Configurations" of the Cadence
Sierra 16FFC Multi-Protocol PHY PMA Specification. It is set to 25MHz
since the only user of Cadence Sierra SERDES, TI J721E SoC provides
input clock frequency of 100MHz. For other frequencies,
cmn_refclk_dig_div/cmn_refclk1_dig_div should be configured
based on the "Common Module Clock Configurations".
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Sierra SERDES IP supports upto 16 lanes (though not all of it
will be enabled in a platform). Allow Sierra driver to support a
maximum of upto 16 lanes.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
A link may have multiple lanes each with a separate reset. Get
reset control "array" in order to reset all the lanes associated
with the link.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The existing configuration done in Cadence Sierra driver is only for
reference and is not used in any platforms. Remove them and configure
both lane cdb and common cdb registers to be used with external
SSC configuration. This is validated in TI J721E platform.
Signed-off-by: Anil Varughese <aniljoy@cadence.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Instead of invoking cdns_sierra_phy_init() from probe, add it in
phy_ops so that it's initialized when the PHY consumer invokes
phy_init()
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
SERDES_16G in TI's J721E SoC uses Cadence Sierra PHY. Add
support to use Cadence Sierra driver in J721E SoC.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Use "regmap" for read and write to Sierra registers. This is in
perparation for adding SERDES_16G support present in TI's J721E
SoC.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Certain platforms like TI J721E using Cadence Sierra Serdes
doesn't provide explicit phy_clk and reset (APB reset) control.
Make them optional here.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cadence has designed a D-PHY that can be used by the, currently in tree,
DSI bridge (DRM), CSI Transceiver and CSI Receiver (v4l2) drivers.
Only the DSI driver has an ad-hoc driver for that phy at the moment, while
the v4l2 drivers are completely missing any phy support. In order to make
that phy support available to all these drivers, without having to
duplicate that code three times, let's create a generic phy framework
driver.
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add a Sierra PHY driver with PCIe and USB support.
The PHY has multiple lanes, which can be configured into
groups, and a generic PHY device is created for each group.
There are two resets controlling the overall PHY block, one
to enable the APB interface for programming registers, and
another to enable the PHY itself. Additionally there are
resets for each PHY lane.
The PHY can be configured in hardware to read register
settings from ROM, or they can be written by the driver.
The sequence of operation on startup is to enable the APB
bus, write the PHY registers (if required) for each lane
group, and then enable the PHY. Each group of lanes
can then be individually controlled using the power_on()/
power_off() function for that generic PHY
Signed-off-by: Alan Douglas <adouglas@cadence.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add driver for the Cadence SD0801 "Torrent" PHY used with the Cadence MHDP
DisplayPort Tx controller.
Integration with the MHDP driver will be the subject of another commit.
Signed-off-by: Scott Telford <stelford@cadence.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
