recover LLD EQs for DB drop interrupts. This includes adding a new
db_lock, a spin lock disabling BH too, used by the recovery thread and
the ring_tx_db() paths to allow db drop recovery.
Clean up initial DB avoidance code.
Add read_eq_indices() - this allows the LLD to use the PCIe mw to
efficiently read hw eq contexts.
Add cxgb4_sync_txq_pidx() - called by iw_cxgb4 to sync up the sw/hw
pidx value.
Add flush_eq_cache() and cxgb4_flush_eq_cache(). This allows iw_cxgb4
to flush the sge eq context cache before beginning db drop recovery.
Add module parameter, dbfoifo_int_thresh, to allow tuning the db
interrupt threshold value.
Add dbfifo_int_thresh to cxgb4_lld_info so iw_cxgb4 knows the threshold.
Add module parameter, dbfoifo_drain_delay, to allow tuning the amount
of time delay between DB FULL and EMPTY upcalls to iw_cxgb4.
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Add platform-specific callback functions for interrupts. This is
needed to do a single read-clear of the CAUSE register and then call
out to platform specific functions for DB threshold interrupts and DB
drop interrupts.
Add t4_mem_win_read_len() - mem-window reads for arbitrary lengths.
This is used to read the CIDX/PIDX values from EC contexts during DB
drop recovery.
Add t4_fwaddrspace_write() - sends addrspace write cmds to the fw.
Needed to flush the sge eq context cache.
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
WakeOnLan was broken in this driver because gp->asleep_wol is a 1-bit
bitfield and it was being assigned WAKE_MAGIC, which is (1 << 5).
gp->asleep_wol remains 0 and the machine never wakes up. Fixed by casting
gp->wake_on_lan to bool. Tested on an iBook G4.
Signed-off-by: Gerard Lledo <gerard.lledo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If register_netdev returns failure, the dev->interrupt and
its transfer buffer should be released, so just fix it.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The transfer buffer of dev->interrupt is allocated in .probe path,
but not freed in .disconnet path, so mark the interrupt URB as
URB_FREE_BUFFER to free the buffer when the URB is destroyed.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Creating a VLAN interface on top of ucc_geth adds 4 bytes
to the frame and the HW controller is not prepared to
TX a frame bigger than 1518 bytes which is 4 bytes too
small for a full VLAN frame. Add 16 bytes which will handle
the a simple VLAN and leaves 12 bytes for future expansion.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a busy network we see ucc_geth is dropping RX pkgs every now
and then. Increase the RX queues HW descriptors from
16 to 32 to deal with this.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bug: The VLAN bit of the MAC RX Status Word is unreliable in several older
supported chips. Sometimes the VLAN bit is not set for valid VLAN packets
and also sometimes the VLAN bit is set for non-VLAN packets that came after
a VLAN packet. This results in a receive length error when VLAN hardware
tagging is enabled.
Fix: Variation on original fix proposed by Mirko.
The VLAN information is decoded in the status loop, and can be
applied to the received SKB there. This eliminates the need for the
separate tag field in the interface data structure. The tag has to
be copied and cleared if packet is copied. This version checked out
with vlan and normal traffic.
Note: vlan_tx_tag_present should be renamed vlan_tag_present, but that
is outside scope of this.
Reported-by: Mirko Lindner <mlindner@marvell.com>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a small packet is received, the driver copies it to a new skb to allow
reusing the full size Rx buffer. The copy was propogating the checksum offload
but not the receive hash information. The bug is impact was mostly harmless
and therefore not observed until reviewing this area of code.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver calls cxgb_vlan_mode() from init_one(). This calls into
synchronize_rx(), which locks all the q locks, but the q locks are not
initialized until cxgb_up() -> setup_sge_qsets(). So move the call to
cxgb_vlan_mode() into cxgb_up(), after the call to setup_sge_qsets().
We also move the body of these functions up higher to avoid having to
a forward declaration.
This was found because of the lockdep warning:
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
Pid: 323, comm: work_for_cpu Not tainted 3.4.0-rc5 #28
Call Trace:
[<ffffffff8106e767>] register_lock_class+0x108/0x2d0
[<ffffffff8106ff42>] __lock_acquire+0xd3/0xd06
[<ffffffff81070fd0>] lock_acquire+0xbf/0xfe
[<ffffffff813862a6>] _raw_spin_lock_irq+0x36/0x45
[<ffffffffa01e71aa>] cxgb_vlan_mode+0x96/0xcb [cxgb3]
[<ffffffffa01f90eb>] init_one+0x8c4/0x980 [cxgb3]
[<ffffffff811fcbf0>] local_pci_probe+0x3f/0x70
[<ffffffff81042206>] do_work_for_cpu+0x10/0x22
[<ffffffff810482de>] kthread+0xa1/0xa9
[<ffffffff8138e234>] kernel_thread_helper+0x4/0x10
Contrary to what lockdep says, the code is not fine: we are locking an
uninitialized spinlock.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the support to bounce buffer added, the skb is coming as nonlinear in the
case of non-DDPed data frames for FCoE, which is mostly ok as the FCoE stack
would take care of that. However, for target mode, we have to set the FC CRC
and FC EOF field to allow the protocol stack to not drop the frame for the last
data frame of that sequence. So fix this by linearizing the skb first before
doing skb_put().
Signed-off-by: Yi Zou <yi.zou@intel.com>
Tested-by: Marcus Dennis <marcusx.e.dennis@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver was freeing memory in shutdown instead of remove. As a result
we were leaking memory if IEEE DCB was enabled and we loaded/unloaded the
driver. This change moves the freeing of the memory into the remove
routine where it belongs.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Maybe it's a typo, but it cause that igbvf can't be initialized successfully.
Set perm_addr value using valid dev_addr, although which is equal to hw.mac.addr.
Signed-off-by: Samuel Liao <samuelliao@tencent.com>
Signed-off-by: Shan Wei <davidshan@tencent.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch sets the automatic speed and duplex detection bits
in MAC_CR to enable the mac to determine its speed automatically
from the phy.
Note this must be done BEFORE the receiver or transmitter is
enabled.
Signed-off-by: Stephane Fillod <fillods@users.sf.net>
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
also explicitly set the phy to advertise 1000 speeds
Signed-off-by: Stephane Fillod <fillods@users.sf.net>
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
smsc75xx phy interrupt acknowledge needs an mdio_write to clear
PHY_INT_SRC instead of just a read like in smsc95xx.
Signed-off-by: Stephane Fillod <fillods@users.sf.net>
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
fix bug in phy_init loop that was ignoring BMCR reset bit, akin to smsc95xx's d946092000
Signed-off-by: Stephane Fillod <fillods@users.sf.net>
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Stephane Fillod <fillods@users.sf.net>
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
smsc75xx needs MII_ACCESS_BUSY to be set to correctly trigger mdio I/O. Note smsc75xx is different from smsc95xx in this regard.
Signed-off-by: Stephane Fillod <fillods@users.sf.net>
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the same issue as reported on smsc95xx, where the
usb device is connected with no ethernet cable plugged-in.
Without this patch sysfs reports the cable as present
flag@flag-desktop:~$ cat /sys/class/net/eth0/carrier
1
while it's not:
flag@flag-desktop:~$ sudo mii-tool eth0
eth0: no link
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver currently leaves elp_work behind when stopping, which
occasionally results in data corruption because work function ends
up accessing freed memory, typical symptoms of this are various
worker_thread crashes. Fix it by cancelling elp_work.
Cc: stable@vger.kernel.org # v2.6.37+
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently SDIO glue frees it's own structure before calling
wl1251_free_hw(), which in turn calls ieee80211_unregister_hw().
The later call may result in a need to communicate with the chip
to stop it (as it happens now if the interface is still up before
rmmod), which means calls are made back to the glue, resulting in
freed memory access.
Fix this by freeing glue data last.
Cc: stable@vger.kernel.org # v2.6.37+
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit 2a19032 (b43: reload phy and bss settings after core restarts)
introduced an unconditional call to b43_op_config() at the end of
b43_op_start(). When firmware fails to load this can wedge the system.
There's no need to reload the configuration after a failed
initialization anyway, so only make the call if initialization was
successful.
BugLink: http://bugs.launchpad.net/bugs/950295
Cc: Felix Fietkau <nbd@openwrt.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"iwlwifi: use correct released ucode version" change
the ucode api ok from 6000G2 to 6000G2B, but it shall belong
to 6030 device series, not the 6005 device series. Fix it
Cc: stable@vger.kernel.org #3.3+
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When our driver device is removed on the AHB bus, our IO memory is never unmapped.
Signed-off-by: Jonathan Bither <jonbither@gmail.com>
Reviewed-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
dpc takes care of all data packets transmissions for sdio function
2. It is possible that it misses some completion events when the
traffic is heavy or it's running on a slow cpu. A linked list is
introduced to make sure dpc is invoked whenever needed.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
SDIO stack doesn't have a structure for function 0. The structure
pointer stored in card->sdio_func[0] is actually for function 1.
With current implementation the register read/write is applied to
function 1. This pathch fixes the issue.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Florian Fainelli <florian@openwrt.org>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Without this patch sysfs reports the cable as present
flag@flag-desktop:~$ cat /sys/class/net/eth0/carrier
1
while it's not:
flag@flag-desktop:~$ sudo mii-tool eth0
eth0: no link
Tested on my Beagle XM.
v2: added mantainer to the list of recipient
Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Acked-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dl2k driver's rio_ioctl call has a few issues:
- No permissions checking
- Implements SIOCGMIIREG and SIOCGMIIREG using the SIOCDEVPRIVATE numbers
- Has a few ioctls that may have been used for debugging at one point
but have no place in the kernel proper.
This patch removes all but the MII ioctls, renumbers them to use the
standard ones, and adds the proper permission check for SIOCSMIIREG.
We can also get rid of the dl2k-specific struct mii_data in favor of
the generic struct mii_ioctl_data.
Since we have the phyid on hand, we can add the SIOCGMIIPHY ioctl too.
Most of the MII code for the driver could probably be converted to use
the generic MII library but I don't have a device to test the results.
Reported-by: Stephan Mueller <stephan.mueller@atsec.com>
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit a4910b7444 has broken promiscuous
mode, which is never set. port->promisc just reflects the last setting
of PROMISCUOUS mode to avoid doing an extra hypercall when it's already
set.
However, since it may fail because of hypervisor permissions, we should
still respect the multicast settings and not simply exit after setting
promiscuous mode.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Cc: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There was a bug in the mask of regtype parameter for registering a
multicast filter. It was ignoring the scope bit, which was wrongly being
used for all filters. The SCOPE_ALL value adds a filter that allows all
multicast packets and ignores the MAC parameter, just what allmulticast
needs. The normals filters, however, should not use SCOPE_ALL.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When RSS is enabled, interrupt vector 0 does not receive any rx traffic.
The rx producer index fields for vector 0's status block should be
considered reserved in this case. This patch changes the code to
respect these reserved fields, which avoids a kernel panic when these
fields take on non-zero values.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changes this beauty into a statement that actually has an effect on amd64.
Tested-by: Per Jessen <per@opensuse.org>
Signed-off-by: Benjamin Poirier <bpoirier@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on the original patch from Ying Cai <ycai@google.com>
This change ensures that the itr/itr_setting adjustment logic is used,
even for the default/compiled-in value.
Context:
When we changed the default InterruptThrottleRate value from default
(3 = dynamic mode) to 8000 for example, only adapter->itr_setting
(which controls interrupt coalescing mode) was set to 8000, but
adapter->itr (which controls the value set in NIC register) was not
updated accordingly. So from ethtool, it seemed the interrupt
throttling is enabled at 8000 intr/s, but the NIC actually was
running in dynamic mode which has lower CPU efficiency especially
when throughput is not high.
CC: Ying Cai <ycai@google.com>
CC: David Decotigny <david.decotigny@google.com>
Signed-off-by: Jeff Kirsher <jeffrey.kirsher@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Following logs where seen on Systems with multiple NICs,
while using MSI interrupts as shown below:
Feb 16 15:09:32 (none) user.notice kernel: 0000:00:0d.0: lan0_0: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:32 (none) user.notice kernel: 0000:40:0d.0: wan0_1: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:32 (none) user.notice kernel: 0000:40:0d.0: lan0_1: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:32 (none) user.warn kernel: 0000:40:0e.0: wan4_0: MSI interrupt
test failed, using legacy interrupt.
Feb 16 15:09:32 (none) user.notice kernel: 0000:00:0e.0: wan1_0: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:33 (none) user.notice kernel: 0000:00:0e.0: lan1_0: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:33 (none) user.notice kernel: 0000:00:0f.0: wan2_0: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:33 (none) user.notice kernel: 0000:00:0f.0: lan2_0: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:33 (none) user.notice kernel: 0000:40:0a.0: wan3_0: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:33 (none) user.notice kernel: 0000:40:0a.0: lan3_0: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:34 (none) user.notice kernel: 0000:40:0e.0: lan4_0: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:34 (none) user.notice kernel: 0000:40:0f.0: wan5_0: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:34 (none) user.notice kernel: 0000:40:0f.0: lan5_0: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
This patch fixes this problem by increasing the msleep from 50 to 100.
Signed-off-by: Prasanna S Panchamukhi <ppanchamukhi@riverbed.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Report correctly the latest released version
of the iwlwifi firmware for all
iwlwifi-supported devices.
Cc: stable@vger.kernel.org #3.3+
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Newer devices have 20 (5000 series) or 30 (6000 series)
hardware queues, rather than the 16 that 4965 had. This
was added to the driver a long time ago, but improperly:
the queue registers for the higher queues aren't just
continuations of the registers for the first 16 queues,
they are in other places. Therefore, the hardware would
lock up when trying to activate queue 16 or above and
the device would have to be restarted.
Thanks goes to Emmanuel who identified this and told me
how the queue programming should be done.
Note that we don't use queues 20 and higher today and
doing so needs more work than this.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The asix.c USB Ethernet driver avoids ending a tx transfer with a zero-
length packet by appending a four-byte padding to transfers whose length
is a multiple of maxpacket. However, the hard-coded 512 byte maxpacket
length is valid for high-speed USB only; full-speed USB uses 64 byte
packets.
Signed-off-by: Ingo van Lil <inguin@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
PHY connect attempts fail if no PHY id is specified in the emac platform
data and another mdio bus has been registered before 'davinci_mdio' bus. In
this case when configuring the interface, there will be an attempt to
connect to already attached PHY on the previously registered mdio bus:
net eth1: PHY already attached
net eth1: could not connect to phy smsc911x-0:01
IP-Config: Failed to open eth1
IP-Config: Device `eth1' not found
Fix this by modifying match_first_device() to match first PHY device
on 'davinci_mdio' bus.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we receive an interrupt too early before we set up ports in the probe
function, there won't be any port ready to handle it.
Only registering the irq after the ports are setup fixes the problem,
and works fine without losing any interrupts.
This causes crashes in some situations:
[c000000f7ff7fd60] d000000008e223f0 .ehea_neq_tasklet+0x78/0x148 [ehea]
[c000000f7ff7fe00] c0000000000b6cac .tasklet_hi_action+0xdc/0x210
[c000000f7ff7fea0] c0000000000b7cc8 .__do_softirq+0x178/0x300
[c000000f7ff7ff90] c000000000022694 .call_do_softirq+0x14/0x24
[c000000f68ee7900] c000000000010e04 .do_softirq+0xec/0x110
[c000000f68ee79a0] c0000000000b789c .irq_exit+0xac/0xe0
[c000000f68ee7a20] c0000000000110bc .do_IRQ+0x114/0x2a8
[c000000f68ee7ae0] c00000000000553c hardware_interrupt_entry+0x18/0x1c
Signed-off-by: David S. Miller <davem@davemloft.net>
Make smsc95xx recalculate the hard_mtu after adjusting the
hard_header_len.
Without this, usbnet adjusts the MTU down to 1488 bytes, and the host is
unable to receive standard 1500-byte frames from the device.
Inspired by same fix on cdc_eem 78fb72f793.
Tested on ARM/Beagle.
Signed-off-by: Stephane Fillod <fillods@users.sf.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
I keep getting the following messages on the log buffer:
[ 2167.097507] ieee80211 phy0: brcms_c_dotxstatus: INTERMEDIATE but not AMPDU
[ 2281.331305] ieee80211 phy0: brcms_c_dotxstatus: INTERMEDIATE but not AMPDU
[ 2281.332539] ieee80211 phy0: brcms_c_dotxstatus: INTERMEDIATE but not AMPDU
[ 2329.876605] ieee80211 phy0: brcms_c_dotxstatus: INTERMEDIATE but not AMPDU
[ 2329.877354] ieee80211 phy0: brcms_c_dotxstatus: INTERMEDIATE but not AMPDU
[ 2462.280756] ieee80211 phy0: brcms_c_dotxstatus: INTERMEDIATE but not AMPDU
[ 2615.651689] ieee80211 phy0: brcms_c_dotxstatus: INTERMEDIATE but not AMPDU
From the code comment I understand that this something that can -
and does, quite frequently - happen.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Acked-by: Franky Lin<frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Driver incorrectly validates command completion: instead of waiting
for a command to be acknowledged it continues execution. Most of the
time driver gets acknowledge of the command completion in a tasklet
before it executes the next one. But sometimes it sends the next
command before it gets acknowledge for the previous one. In such a
case one of the following error messages appear in the log:
Failed to send SYSTEM_CONFIG: Already sending a command.
Failed to send ASSOCIATE: Already sending a command.
Failed to send TX_POWER: Already sending a command.
After that you need to reload the driver to get it working again.
This bug occurs during roaming (reported by Sam Varshavchik)
https://bugzilla.redhat.com/show_bug.cgi?id=738508
and machine booting (reported by Tom Gundersen and Mads Kiilerich)
https://bugs.archlinux.org/task/28097https://bugzilla.redhat.com/show_bug.cgi?id=802106
This patch doesn't fix the delay issue during firmware load.
But at least device now works as usual after boot.
Cc: stable@kernel.org
Signed-off-by: Stanislav Yakovlev <stas.yakovlev@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
