Be more explicit in some comments.
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
On some QNAP NAS devices the rtc can wake the machine. Several people
noticed that once the machine was woken this way it fails to shut down.
That's because the driver fails to acknowledge the interrupt and so it
keeps active and restarts the machine immediatly after shutdown. See
https://bugs.debian.org/794266 for a bug report.
Doing this correctly requires to interpret the INT2 flag of the first read
of the STATUS1 register because this bit is cleared by read.
Note this is not maximally robust though because a pending irq isn't
detected when the STATUS1 register was already read (and so INT2 is not
set) but the irq was not disabled. But that is a hardware imposed problem
that cannot easily be fixed by software.
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
There were two deviations from the reference manual: you have to wait
half a second when POC is active and you might have to repeat
initialization when POC or BLD are still set after the sequence.
Note however that as POC and BLD are cleared by read the driver might
not be able to detect that a reset is necessary. I don't have a good
idea how to fix this.
Additionally report the value read from STATUS1 to the caller. This
prepares the next patch.
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
There are several issues fixed in this patch:
- When alarm isn't enabled, set .enabled to zero instead of returning
-EINVAL.
- Ignore how IRQ1 is configured when determining if IRQ2 is on.
- The three alarm registers have an enable flag which must be
evaluated.
- The chip always triggers when the seconds register gets 0.
Note that the rtc framework however doesn't handle the result correctly
because it doesn't check wday being initialized and so interprets an
alarm being set for 10:00 AM in three days as 10:00 AM tomorrow (or
today if that's not over yet).
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The rtc core doesn't give broken dates to a driver's .set_alarm
callback, so there should be no need for validation.
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
This rtc doesn't support triggering on years, so don't assign tm_year
instead of claiming the alarm is to trigger in year 67435.
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The rtc chip doesn't support triggering on month and year. So just don't
assign the respective fields in .read_alarm and let the rtc core
interpret this accordingly.
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Since commit d68778b80d ("rtc: initialize output parameter for read
alarm to "uninitialized"") there is no need to explicitly set
unsupported members to -1. So drop the respective assignments from
drivers.
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The reset value of weekday is 0x1. This is wrong since
the reset values of the day/month/year make up to Jan 1 2001.
When computed weekday comes out to be Monday. On a scale
of 1-7(Sunday - Saturday) it should be 0x2. So we should not
be relying on the reset value.
Hence compute the wday using the current date/month/year values.
Check if reset wday is any different from the computed wday,
If different then set the wday which we computed using
date/month/year values.
Document Referred:
http://ww1.microchip.com/downloads/en/DeviceDoc/20002266F.pdf
Fixes: 1d1945d261 "drivers/rtc/rtc-ds1307.c: add alarm support for mcp7941x chips"
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
m48t86.h belongs to include/linux/platform_data/
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Alexander Clouter <alex@digriz.org.uk>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The previous workaround may still fail as there are actually 4 retries to
be done to ensure the communication succeed. Also, some I2C adapter drivers
may return -EIO instead of -ENXIO.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The mc146818_get_time/mc146818_set_time functions are rather large
inline functions in a global header file and are used in several
drivers and in x86 specific code.
Here we move them into a separate .c file that is compiled whenever
any of the users require it. This also lets us remove the linux/acpi.h
header inclusion from mc146818rtc.h, which in turn avoids some
warnings about duplicate definition of the TRUE/FALSE macros.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
nn10300 has a dependency on mc146818_get_time/mc146818_set_time,
which we want to move from the mc146818rtc.h header into the
rtc subsystem, which in turn is not usable on mn10300.
This changes mn10300 to use the modern rtc-cmos driver instead
of the old RTC driver, and that in turn lets us completely
remove the read_persistent_clock/update_persistent_clock callbacks.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
While the EFI spec mandates an RTC, not every implementation actually adheres
to that rule (or can adhere to it - some systems just don't have an RTC).
For those, we really don't want to probe the EFI RTC driver at all, because if
we do we'd get a non-functional driver that does nothing useful but only spills
our kernel log with warnings.
Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Add support for Maxim max6916 RTC.
Signed-off-by: Venkat Prashanth B U <venkat.prashanth2498@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Use sign_extend32() instead of open coding sign extension.
Signed-off-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The day of month is checked in ds1685_rtc_read_alarm
and ds1685_rtc_set_alarm.
Multiple errors exist in the day of month check.
Operator ! has a higher priority than &&.
(!(mday >= 1) && (mday <= 31)) is false for mday == 32.
When verifying the day of month the binary and the BCD mode
have to be considered.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
This patch fixes a RTC wakealarm issue, namely, the event fires during
hibernate and is not cleared from the list, causing hwclock to block.
The current enqueuing does not trigger an alarm if any expired timers
already exist on the timerqueue. This can occur when a RTC wake alarm
is used to wake a machine out of hibernate and the resumed state has
old expired timers that have not been removed from the timer queue.
This fix skips over any expired timers and triggers an alarm if there
are no pending timers on the timerqueue. Note that the skipped expired
timer will get reaped later on, so there is no need to clean it up
immediately.
The issue can be reproduced by putting a machine into hibernate and
waking it with the RTC wakealarm. Running the example RTC test program
from tools/testing/selftests/timers/rtctest.c after the hibernate will
block indefinitely. With the fix, it no longer blocks after the
hibernate resume.
BugLink: http://bugs.launchpad.net/bugs/1333569
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
All architectures using this driver are now converted to
provide their own operations, so this one can be turned
into a trivial stub driver relying on its platform data.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The rtc-generic driver provides an architecture specific
wrapper on top of the generic rtc_class_ops abstraction,
and powerpc has another abstraction on top, which is a bit
silly.
This changes the powerpc rtc-generic device to provide its
rtc_class_ops directly, to reduce the number of layers
by one.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The rtc-generic driver provides an architecture specific
wrapper on top of the generic rtc_class_ops abstraction,
and m68k has another abstraction on top, which is a bit
silly.
This changes the m68k rtc-generic device to provide its
rtc_class_ops directly, to reduce the number of layers
by one.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The rtc-generic driver provides an architecture specific
wrapper on top of the generic rtc_class_ops abstraction,
and on pa-risc, that is implemented using an open-coded
version of rtc_time_to_tm/rtc_tm_to_time.
This changes the parisc rtc-generic device to provide its
rtc_class_ops directly, using the normal helper functions,
which makes this y2038 safe (on 32-bit) and simplifies
the implementation.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The rtc-generic driver provides an architecture specific
wrapper on top of the generic rtc_class_ops abstraction,
and on sh, that goes through another indirection using
the rtc_sh_get_time/rtc_sh_set_time functions.
This changes the sh rtc-generic device to provide its
rtc_class_ops directly, skipping one of the abstraction
levels.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Rich Felker <dalias@libc.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Commit 3195ef59cb ("x86: Do full rtc synchronization with ntp") had
the side-effect of unconditionally enabling the RTC_LIB symbol on x86,
which in turn disables the selection of the CONFIG_RTC and
CONFIG_GEN_RTC drivers that contain a two older implementations of
the CONFIG_RTC_DRV_CMOS driver.
This removes x86 from the list for genrtc, and changes all references
to the asm/rtc.h header to instead point to the interfaces
from linux/mc146818rtc.h.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Drivers should not really include stuff from asm-generic directly,
and the PC-style cmos rtc driver does this in order to reuse the
mc146818 implementation of get_rtc_time/set_rtc_time rather than
the architecture specific one for the architecture it gets built for.
To make it more obvious what is going on, this moves and renames the
two functions into include/linux/mc146818rtc.h, which holds the
other mc146818 specific code. Ideally it would be in a .c file,
but that would require extra infrastructure as the functions are
called by multiple drivers with conflicting dependencies.
With this change, the asm-generic/rtc.h header also becomes much
more generic, so it can be reused more easily across any architecture
that still relies on the genrtc driver.
The only caller of the internal __get_rtc_time/__set_rtc_time
functions is in arch/alpha/kernel/rtc.c, and we just change those
over to the new naming.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
rtc drivers are supposed to set values they don't support to -1. To
simplify this for drivers and also make it harder for them to get it
wrong initialize the values to -1.
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
This module is loaded by the related mfd driver which has
the needed MODULE_DEVICE_TABLE(i2c,...).
This patch fix the modalias when the rtc driver is built
as a module, so the right name is used.
Everything operates correctly when this module is builtin.
Fixes: esdc59ed3865 ("rtc: add RTC driver for TPS6586x")
Signed-off-by: Nicolas Chauvet <kwizart@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The added support for SPI mode made it possible to configure the driver
when I2C is disabled, leaving an unused device table:
drivers/rtc/rtc-rv3029c2.c:794:29: error: 'rv3029_id' defined but not used [-Werror=unused-variable]
This moves the table inside of the #ifdef section that has the
only user, to avoid the harmless warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: d08f50dd0afc ("rtc: rv3029: Add support of RV3049")
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The R2025SD chip, according to its data sheet, sets the /XST
bit to zero if the oscillator stops. Hence the check for this
condition was wrong.
Signed-off-by: Thomas Koeller <thomas.koeller@baslerweb.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The bin2bcd function in set_time is uncorrect on weekdays as the
bit mask should be done at the end of arithmetic operations.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The RTC RV3029 handles different types of alarms : seconds, minutes, ...
These alarms can be enabled or disabled individually using an AE_x bit
which is the last bit (BIT(7)) on each alarm registers.
To prepare the alarm IRQ support, the current code enables all the alarm
types by setting each AE_x to 1.
It also fixes others alarms issues :
- month and weekday errors : it was performing -1 instead of +1.
- wrong use of bit mask with bin2bcd
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Remove some checks from checkpatch such as spaces around arithmetic
operations or prefer "unsigned int".
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Add support of Microcrystal RV3049 RTC (SPI) using regmap on the
RV3029 (I2C) driver.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
To add support of rv3049, the current driver is converted to use regmap.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
To prepare the use of regmap to add the support of RV-3049, all the
'i2c' in functions's names are removed.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
stmp3xxx_wdt_register() can fail as platform_device_alloc() or
platform_device_add() can fail. But when it fails it failed silently.
Lets print out an error message on failure so that user will atlest
know that there was some error.
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The IS_ENABLED() macro checks if a Kconfig symbol has been enabled either
built-in or as a module, use that macro instead of open coding the same.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The rtc->ops_lock would be accessed in ds3232_irq() without being
initialized as rtc_device_register() is called too late.
So move devm_rtc_device_register() just before registering irq handler
to initialize rtc->ops_lock earlier.
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
If enable_irq_wake fails, we should return that error code so that
entering suspend fails. Otherwise we will get a WARNING along with
the hint of a unbalanced wake disable:
Unbalanced IRQ 37 wake disable
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
We program RTC time using SET_TIME_WRITE register and read the RTC
current time using CURRENT_TIME register. When we set the time by
writing into SET_TIME_WRITE Register and immediately try to read the
rtc time from CURRENT_TIME register, the previous old value is
returned instead of the new loaded time. This is because RTC takes
nearly 1 sec to update the new loaded value into the CURRENT_TIME
register. This behaviour is expected in our RTC IP.
This patch updates the driver to read the current time from SET_TIME_WRITE
register instead of CURRENT_TIME when rtc time is requested within an 1sec
period after setting the RTC time. Doing so will ensure the correct time is
given to the user.
Since there is a delay of 1sec in updating the CURRENT_TIME we are loading
set time +1sec while programming the SET_TIME_WRITE register, doing this
will give correct time without any delay when read from CURRENT_TIME.
Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The RTC core handles it since 6610e08 (RTC: Rework RTC code to use
timerqueue for events). So far, only the callbacks to the RTC core have
been removed, but not the handlers. Do this now.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The RTC core handles it since 6610e08 (RTC: Rework RTC code to use
timerqueue for events).
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
This flag is a no-op now (see commit 47b0eeb3dc "clk: Deprecate
CLK_IS_ROOT", 2016-02-02) so remove it.
Cc: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Michael Tatarinov <kukabu@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
This flag is a no-op now (see commit 47b0eeb3dc "clk: Deprecate
CLK_IS_ROOT", 2016-02-02) so remove it.
Cc: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
This flag is a no-op now (see commit 47b0eeb3dc "clk: Deprecate
CLK_IS_ROOT", 2016-02-02) so remove it.
Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
