Also use them instead of a magic value when enabling the interrupts.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
at803x currently automatically enables the RGMII TX clock delay when the
phy interface mode is PHY_INTERFACE_MODE_RGMII_TXID. The same should be
done when PHY_INTERFACE_MODE_RGMII_ID is specified.
Use a similar logic to enable the RGMII RX clock delay as well.
at803x_context_{save,restore} were not touched because these are only
used on AR8030 which is a RMII phy (RGMII clock delays are irrelevant).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 8030 is only a "RMII Fast Ethernet PHY", thus it must not have the
SUPPORTED_1000* bits set.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The operstate of a networking device initially IF_OPER_UNKNOWN aka
"unknown", updated on carrier state changes (with carrier state being on
by default). This means it will stay unknown unless the carrier state
goes to off at some point, which is not the case if the phy is already
up/connected at startup.
Explicitly turn off the carrier on phy attach, leaving the phy state
machine to turn the carrier on when it has done the initial negotiation.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
It used to be that bus->irq was a pointer but after e7f4dc3536
('mdio: Move allocation of interrupts into core') it's an array inside
the mdio struct, so it can never be NULL. Let's remove the check.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If bus = kzalloc() fails then we end up dereferencing bus when we do
"bus->irq[i] = PHY_POLL;". The code is a little simpler if we reverse
the NULL check and return directly on failure.
Fixes: e7f4dc3536 ('mdio: Move allocation of interrupts into core')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/bonding/bond_main.c
drivers/net/ethernet/mellanox/mlxsw/spectrum.h
drivers/net/ethernet/mellanox/mlxsw/spectrum_switchdev.c
The bond_main.c and mellanox switch conflicts were cases of
overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
LAN8740 has a different phy_id than LAN8710/LAN8720.
Signed-off-by: Joshua Henderson <joshua.henderson@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 651df21835 ("phy: micrel: Fix finding PHY properties in MAC
node.") only fixes finding PHY properties in MAC node for KSZ9021. This
commit applies the same fix for KSZ9031.
Fixes: 8b63ec1837 ("phylib: Make PHYs children of their MDIO bus, not the bus' parent.")
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Henri Roosen <henri.roosen@ginzinger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make device_free and device_remove operations in the mdio device
structure, so the core code does not need to differentiate between
phy devices and generic mdio devices.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all devices on an MDIO bus are PHYs. Meaning not all MDIO drivers
are PHY drivers. Add support for generic MDIO drivers.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make it clear that mdiobus_scan () will only find devices which have a
vendor/product ID in registers 2 and 3. These are typically PHY
devices. Other sort of MDIO devices, such as switches, are not
expected to be found during the scan.
Similarly, __mdiobus_register(), which calls mdiobus_scan() will only
find PHY devices, and other sorts of MDIO devices are expected to be
instantiated from device tree.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function should work with any sort of MDIO device which can be
probed on the bus, not just PHY devices. So generalise it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Matching a driver to a device has both generic parts, and parts which
are specific to PHY devices. Move the PHY specific parts into
phy_device.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than have each driver set the driver owner field, do it once in
the core code. This will also help with later changes, when the device
structure will move.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MDIO PM operations are really PHY device PM operations. So move
them into phy_device. This will be needed when we support devices on
the mdio bus which are not PHYs.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mdio_bus exports three attributes:
- PHY ID is the unique 32-bits identifier for a MDIO device implementing
standard MII registers MII_PHYSID1/2, which is not guaranteed to be the
case for non-standard compliant devices (e.g: Ethernet switches)
- PHY interface describes the data-path of the PHY/MDIO device, which is
not strictly a PHY thing, but is required and needed for PHY devices to
function, a MDIO device could be a control device exclusively
- PHY has fixups describes what the PHY driver may have done, so
completely PHY specific
These are all phy attributes, not generic mdio attributes. So move the
attributes into the phy device code.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than have drivers directly manipulate the mii_bus structure,
provide and API for registering and unregistering devices on an MDIO
bus, and performing lookups.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all devices attached to an MDIO bus are phys. So add an
mdio_device structure to represent the generic parts of an mdio
device, and place this structure into the phy_device.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Have mdio_alloc() create the array of interrupt numbers, and
initialize it to POLLING. This is what most MDIO drivers want, so
allowing code to be removed from the drivers.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than use devm_kzalloc(), use the mdio helper function.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many Ethernet drivers contain the same netdev_info() print statement
about the attached phy. Move it into the phy device code. Additionally
add a varargs function which can be used to append additional
information.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The address of the device can be determined from the phydev structure,
rather than passing it as a parameter.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a phydev_name() function, to help with moving some structure members
from phy_device.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for moving some of the phy_device structure members,
add macros for printing errors and debug information.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY counters receiver errors and errors while idle.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY counters receiver errors and errors while idle.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/geneve.c
Here we had an overlapping change, where in 'net' the extraneous stats
bump was being removed whilst in 'net-next' the final argument to
udp_tunnel6_xmit_skb() was being changed.
Signed-off-by: David S. Miller <davem@davemloft.net>
mdiobus_alloc() might return NULL, but its return value is not
checked in mdio_mux_init(). This could potentially lead to a NULL
pointer dereference. Fix it by checking the return value
Fixes: 0ca2997d14 ("netdev/of/phy: Add MDIO bus multiplexer support.")
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 8b63ec1837 ("phylib: Make PHYs children of their MDIO bus,
not the bus' parent.") changed the parenting of PHY devices, making
them a child of the MDIO bus, instead of the MAC device. This broken
the Micrel PHY driver which has a deprecated feature of allowing PHY
properties to be placed into the MAC node.
In order to find the MAC node, we need to walk up the tree of devices
until we find one with an OF node attached.
Reported-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Suggested-by: David Daney <david.daney@cavium.com>
Acked-by: David Daney <david.daney@cavium.com>
Fixes: 8b63ec1837 ("phylib: Make PHYs children of their MDIO bus, not the bus' parent.")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Device tree properties for a phy device are expected to be in the phy
node. The current code for the DP83867 also tries to look in the
parent node. The devices binding documentation does not mention this,
no current device tree file makes use of this, and it is not behaviour
we want. So remove looking in the parent device.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/renesas/ravb_main.c
kernel/bpf/syscall.c
net/ipv4/ipmr.c
All three conflicts were cases of overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible to address another chip on same MDIO bus. The case is
correctly handled for media advertising. It is taken into account
only if mii_data->phy_id == phydev->addr. However, this condition
was missing for reset case.
Signed-off-by: Jérôme Pouiller <jezz@sysmic.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a PHY entry for the Broadcom BCM7435 chips, this is a 40nm
generation Ethernet PHY which is analogous to its 7425 and 7429 counter
parts.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit fcb26ec5b1 ("broadcom: move all PHY_ID's to header")
updated broadcom_tbl to use PHY_IDs, but incorrectly replaced 0x0143bca0
with PHY_ID_BCM5482 (making a duplicate entry, and completely omitting
the original). Fix that.
Fixes: fcb26ec5b1 ("broadcom: move all PHY_ID's to header")
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
The NOLINK state will poll the phy once a second to see if the link
has come up. If the phy has an interrupt line, this polling can be
skipped, since the phy should interrupt when the link returns.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 88E1540 can be found embedded in the Marvell 88E6352 switch. It
is compatible with the 88E1510, so add support for it, using the
88E1510 specific functions.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for the Vitesse VSC8601 PHY. Generic functions are
used for everything except interrupt handling.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 77a993942 "phy/at8031: enable at8031 to work on interrupt mode"
added interrupt support for the 8031 PHY but left out the other two
chips supported by this driver.
This patch sets the .ack_interrupt and .config_intr functions for the
8030 and 8035 drivers as well.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Quite a lot of activity in SPI this cycle, almost all of it in drivers
with a few minor improvements and tweaks in the core.
- Updates to pxa2xx to support Intel Broxton and multiple chip selects.
- Support for big endian in the bcm63xx driver.
- Multiple slave support for the mt8173
- New driver for the auxiliary SPI controller in bcm2835 SoCs.
- Support for Layerscale SoCs in the Freescale DSPI driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWOehzAAoJECTWi3JdVIfQTPYH+wYMDG8gAIw2s0AJ4DvVe4qZ
sOAm1UgUJZxssrEA6BNqbfM0dfRo+oQJKmRd0Dc5n7LEMsYHdI/5yKHk8PCS6ZzD
iQyQCzbd0thDAqwuPaMP62cyPDHwyJX22VGTsgVnj6AZqAQ+9+g4SPKhFnm1Mlm4
hmDi6fdSrsqo8k8gkpVN8RFOfVsjAV1dLtAauQRWDHrqMxXURSrKG76eqAqUa5bn
BLPXBoj5PA0DMLPO2j+ADZwWN723LrI2mSSlc+ThjEX/OIt2OhAoiOTV5RPqaafy
TIsCkh68q/gYAsL5HtvvmgZByl41FLYiO0Z+rXmWUyMMbnvhZTLws9S2BNpBLuk=
=DgXG
-----END PGP SIGNATURE-----
Merge tag 'spi-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"Quite a lot of activity in SPI this cycle, almost all of it in drivers
with a few minor improvements and tweaks in the core.
- Updates to pxa2xx to support Intel Broxton and multiple chip selects.
- Support for big endian in the bcm63xx driver.
- Multiple slave support for the mt8173
- New driver for the auxiliary SPI controller in bcm2835 SoCs.
- Support for Layerscale SoCs in the Freescale DSPI driver"
* tag 'spi-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (87 commits)
spi: pxa2xx: Rework self-initiated platform data creation for non-ACPI
spi: pxa2xx: Add support for Intel Broxton
spi: pxa2xx: Detect number of enabled Intel LPSS SPI chip select signals
spi: pxa2xx: Add output control for multiple Intel LPSS chip selects
spi: pxa2xx: Use LPSS prefix for defines that are Intel LPSS specific
spi: Add DSPI support for layerscape family
spi: ti-qspi: improve ->remove() callback
spi/spi-xilinx: Fix race condition on last word read
spi: Drop owner assignment from spi_drivers
spi: Add THIS_MODULE to spi_driver in SPI core
spi: Setup the master controller driver before setting the chipselect
spi: dw: replace magic constant by DW_SPI_DR
spi: mediatek: mt8173 spi multiple devices support
spi: mediatek: handle controller_data in mtk_spi_setup
spi: mediatek: remove mtk_spi_config
spi: mediatek: Update document devicetree bindings to support multiple devices
spi: fix kernel-doc warnings about missing return desc in spi.c
spi: fix kernel-doc warnings about missing return desc in spi.h
spi: pxa2xx: Align a few defines
spi: pxa2xx: Save other reg_cs_ctrl bits when configuring chip select
...
Minor overlapping changes in net/ipv4/ipmr.c, in 'net' we were
fixing the "BH-ness" of the counter bumps whilst in 'net-next'
the functions were modified to take an explicit 'net' parameter.
Signed-off-by: David S. Miller <davem@davemloft.net>
In the packet timestamping function, check that the ptp version and
protocol of the packet matches what we have configured the hardware to
actually generate timestamps for, before looking/waiting for a timestamp.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The list of rx timestamps are currently only pruned of old entries when a
new entry is inserted. If no new entries are added, old timestamps may
survive beyond their lifetime, possible causing them to be attached to
packets with the same sequence number after a rollover.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently rx_timestamp_work reschedules itself as a regular workqueue item,
effectively causing it run constantly as long as there are packets left in
the queue. Fix by using delayed workqueue items, limiting it to run only
every two jiffies.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only using the message type and sequence id for matching timestamps
with packets is error prone, as multiple clients may very well be
sending packets with the same messagetype and timestamp at the same
time. Fix by extending the check to include the hash of bytes 20-29
(source id in PTPv2) that is provided with the timestamps.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When probing devices-in-package for a c45 phy, device zero is the last
device to probe, however, if driver reads 0 from device zero,
c45_ids->devices_in_package is set to '0', the loop condition of probing
will be matched again, see codes below:
for (i = 1;i < num_ids && c45_ids->devices_in_package == 0;i++)
driver will run in a dead loop.
This patch restructures the bug and confusing loop, it provides a helper
function get_phy_c45_devs_in_pkg which to read devices-in-package registers
of a MMD, and rewrites the loop with using the helper function.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An spi_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
for_each_available_child_of_node performs an of_node_get on each iteration, so
a break out of the loop requires an of_node_put.
A simplified version of the semantic patch that fixes this problem is as
follows (http://coccinelle.lip6.fr):
// <smpl>
@@
expression root,e;
local idexpression child;
@@
for_each_available_child_of_node(root, child) {
... when != of_node_put(child)
when != e = child
(
return child;
|
+ of_node_put(child);
? return ...;
)
...
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
for_each_available_child_of_node performs an of_node_get on each iteration, so
a break out of the loop requires an of_node_put.
A simplified version of the semantic patch that fixes this problem is as
follows (http://coccinelle.lip6.fr):
// <smpl>
@@
local idexpression r.n;
expression r,e;
@@
for_each_available_child_of_node(r,n) {
...
(
of_node_put(n);
|
e = n
|
+ of_node_put(n);
? break;
)
...
}
... when != n
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/ipv6/xfrm6_output.c
net/openvswitch/flow_netlink.c
net/openvswitch/vport-gre.c
net/openvswitch/vport-vxlan.c
net/openvswitch/vport.c
net/openvswitch/vport.h
The openvswitch conflicts were overlapping changes. One was
the egress tunnel info fix in 'net' and the other was the
vport ->send() op simplification in 'net-next'.
The xfrm6_output.c conflicts was also a simplification
overlapping a bug fix.
Signed-off-by: David S. Miller <davem@davemloft.net>
Since nested variants of mdiobus_read/write are used in multiple
drivers, add nested variants in the mdiobus core.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Very rarely, the KSZ9031 will appear to complete autonegotiation, but
will drop all traffic afterwards. When this happens, the idle error
count will read 0xFF after autonegotiation completes. Reset the PHY
when in that state.
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the TI DP83848 Ethernet PHY device.
The DP83848 is a highly reliable, feature rich, IEEE 802.3 compliant
single port 10/100 Mb/s Ethernet Physical Layer Transceiver supporting
the MII and RMII interfaces.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This header file only contains the platform data structure definition,
so move it to the include/linux/platform_data/ directory.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some boards the energy enable detect mode leads in
trouble with some switches, so make the enabling of
this mode configurable through DT.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/usb/asix_common.c
net/ipv4/inet_connection_sock.c
net/switchdev/switchdev.c
In the inet_connection_sock.c case the request socket hashing scheme
is completely different in net-next.
The other two conflicts were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
The 'bcm-phy-lib.c', added as a part of the commit
"net: phy: Add Broadcom phy library for common interfaces"
was missing the module license. This was causing an issue
when the library is built as a module; "module license
'unspecified' taints kernel".
This patch fixes the issue by adding the module license,
author and description to the bcm-phy-lib.c file.
Fixes: a1cba5613e ("net: phy: Add Broadcom phy library for
common interfaces")
Signed-off-by: Arun Parameswaran <arunp@broadcom.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use module_phy_driver macro to simplify the code a bit.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
"Y" was the right answer for MDIO_OCTEON when this option was only
available on CAVIUM_OCTEON_SOC. But now that the option is visible on
all (64-bit) systems, this piece of advice no longer makes sense. This
helper module is selected automatically by drivers which need it
anyway.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Fixes: a6d6786452 ("net: mdio-octeon: Modify driver to work on both ThunderX and Octeon")
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Sunil Goutham <sgoutham@cavium.com>
Cc: Radha Mohan Chintakuntla <rchintakuntla@cavium.com>
Cc: David Daney <david.daney@cavium.com>
Cc: David S. Miller <davem@davemloft.net>
Acked-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modified the bcm7xxx phy driver to remove local core register
defines and use the common ones from "include/linux/brcmphy.h"
Signed-off-by: Arun Parameswaran <arunp@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the Broadcom Cygnus SoCs internal PHY's.
The PHYs are 1000M/100M/10M capable with support for 'EEE'
and 'APD' (Auto Power Down).
This driver supports the following Broadcom Cygnus SoCs:
- BCM583XX (BCM58300, BCM58302, BCM58303, BCM58305)
- BCM113XX (BCM11300, BCM11320, BCM11350, BCM11360)
The PHY's on these SoC's require some workarounds for
stable operation, both during configuration time and
during suspend/resume. This driver handles the
application of the workarounds.
Signed-off-by: Arun Parameswaran <arunp@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the Broadcom phy library to consolidate common
interfaces shared by Broadcom phy's.
Moved the common interfaces to the 'bcm-phy-lib.c' and updated
the Broadcom PHY drivers to use the new APIs.
Signed-off-by: Arun Parameswaran <arunp@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the Broadcom iProc MDIO bus interface.
The MDIO interface can be found in the Broadcom iProc family Soc's.
The MDIO bus is accessed using a combination of command and data
registers. This MDIO driver provides access to the Etherent GPHY's
connected to the MDIO bus.
Signed-off-by: Arun Parameswaran <arunp@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper to allow ethernet drivers to limit the speed of a phy
(that they are attached to).
This mainly involves factoring out the business-end of
of_set_phy_supported() and exporting a new symbol.
This code seems to be open coded in several places, in several different
variants.
It is is envisaged that this will be used in situations where setting the
"max-speed" property in DT is not appropriate, e.g. because the maximum
speed is not a property of the phy hardware.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the docbook comment for __mdiobus_register() to include the new
module owner argument. This resolves a warning found by the 0-day
builder.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Read the standard link partner advertisment registers and store it in
phydev->lp_advertising, so ethtool can report this information to
userspace via ethtool. Zero it as per genphy if autonegotiation is
disabled. Tested with a Marvell 88E1512 PHY.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a phy_device_remove() function to complement phy_device_register(),
which undoes the effects of phy_device_register() by removing the phy
device from visibility, but not freeing it.
This allows these details to be moved out of the mdio bus code into
the phy code where this action belongs.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Validate that the phy_device passed into fixed_phy_update_state() is a
fixed-phy device before walking the list of phys for a fixed phy at the
same address.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Take a refcount on the phy struct device when the phy device is attached
to a network device, and drop it after it's detached. This ensures that
a refcount is held on the phy device while the device is being used by
a network device, thereby preventing the phy_device from being
unexpectedly kfree()'d by phy_device_release().
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Re-implement the mdiobus module refcounting to ensure that we actually
ensure that the mdiobus module code does not go away while we might call
into it.
The old scheme using bus->dev.driver was buggy, because bus->dev is a
class device which never has a struct device_driver associated with it,
and hence the associated code trying to obtain a refcount did nothing
useful.
Instead, take the approach that other subsystems do: pass the module
when calling mdiobus_register(), and record that in the mii_bus struct.
When we need to increment the module use count in the phy code, use
this stored pointer. When the phy is deteched, drop the module
refcount, remembering that the phy device might go away at that point.
This doesn't stop the mii_bus going away while there are in-use phys -
it merely stops the underlying code vanishing.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_mdio_find_bus() leaks a struct device refcount, caused by using
class_find_device() and not realising that the device reference has
its refcount incremented:
* Note, you will need to drop the reference with put_device() after use.
...
while ((dev = class_dev_iter_next(&iter))) {
if (match(dev, data)) {
get_device(dev);
break;
}
Update the comment, and arrange for the phy code to drop this refcount
when disposing of a reference to it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 1298267b54.
That commit claim that the Vitesse VSC8641 is compatible with Vitesse
82xx. But this is not true. It seems that all the registers used
in Vitesse phy driver are not compatible between 8641 and 82xx.
It does cause malfunction of the Ethernet on p1010rdb-pa board.
So we definitely need a rework in order to support the 8641 phy
in this driver.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add Microchip LAN88XX phy driver for phylib.
Signed-off-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I've noticed that fixed_phy_register() ignores its 'irq' parameter instead of
passing it to fixed_phy_add(). Luckily, fixed_phy_register() seems to always
be called with PHY_POLL for 'irq'... :-)
Fixes: a759512174 ("net: phy: extend fixed driver with fixed_phy_register()")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 8b63ec1837 ("phylib: Make PHYs children of their MDIO bus, not
the bus' parent.") uncovered a problem in mdiobus_unregister() which
leads to this warning when I reboot an APM Mustang (arm64) platform:
WARNING: CPU: 7 PID: 4239 at fs/sysfs/group.c:224 sysfs_remove_group+0xa0/0xa4()
sysfs group fffffe0000e07a10 not found for kobject 'xgene-mii-eth0:03'
...
CPU: 7 PID: 4239 Comm: reboot Tainted: G E 4.2.0-0.18.el7.test15.aarch64 #1
Hardware name: AppliedMicro Mustang/Mustang, BIOS 1.1.0 Aug 26 2015
Call Trace:
[<fffffe000009739c>] dump_backtrace+0x0/0x170
[<fffffe000009752c>] show_stack+0x20/0x2c
[<fffffe00007436f0>] dump_stack+0x78/0x9c
[<fffffe00000c2cb4>] warn_slowpath_common+0xa0/0xd8
[<fffffe00000c2d60>] warn_slowpath_fmt+0x74/0x88
[<fffffe0000293d3c>] sysfs_remove_group+0x9c/0xa4
[<fffffe00004a8bac>] dpm_sysfs_remove+0x5c/0x70
[<fffffe000049b388>] device_del+0x44/0x208
[<fffffe000049b578>] device_unregister+0x2c/0x7c
[<fffffe000050dc68>] mdiobus_unregister+0x48/0x94
[<fffffe000052afd0>] xgene_enet_mdio_remove+0x28/0x44
[<fffffe000052d3f0>] xgene_enet_remove+0xd0/0xd8
[<fffffe000052d424>] xgene_enet_shutdown+0x2c/0x3c
[<fffffe00004a204c>] platform_drv_shutdown+0x24/0x40
[<fffffe000049d4f4>] device_shutdown+0xf0/0x1b4
[<fffffe00000e31ec>] kernel_restart_prepare+0x40/0x4c
[<fffffe00000e32f8>] kernel_restart+0x1c/0x80
[<fffffe00000e3670>] SyS_reboot+0x17c/0x250
The problem is that mdiobus_unregister() deletes the bus device before
unregistering the phy devices on the bus. This wasn't a problem before
because the phys were not children of the bus:
/sys/devices/platform/APMC0D05:00/net/eth0/xgene-mii-eth0:03
/sys/devices/platform/APMC0D05:00/net/eth0/xgene-mii-eth0
But now that they are:
/sys/devices/platform/APMC0D05:00/net/eth0/xgene-mii-eth0/xgene-mii-eth0:03
when mdiobus_unregister deletes the bus device, the phy subdirs are
removed from sysfs also. So when the phys are unregistered afterward,
we get the warning. This patch changes the order so that phys are
unregistered before the bus device is deleted.
Fixes: 8b63ec1837 ("phylib: Make PHYs children of their MDIO bus, not the bus' parent.")
Signed-off-by: Mark Salter <msalter@redhat.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Mark Langsdorf <mlangsdo@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
What features a phy supports is masked in genphy_config_init() by
looking at the PHYs BMSR register.
If the link is down, fixed_phy_update_regs() will only set the auto-
negotiation capable bit in BMSR. Thus genphy_config_init() comes to
the conclusion the PHY can only perform 10/Half, and masks out the
higher speed features. If however the link it up, BMSR is set to
indicate the speed the PHY is capable of auto-negotiating, and
genphy_config_init() does not mask out the high speed features.
To fix this, when the link is down, have fixed_phy_update_regs() leave
the link status, auto-negotiation complete, and link partner
capabilities unset, but set all the local capabilities depending on
the fixed phy speed.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
An SFP module may have a link up/down status pin which can be
connection to a GPIO line of the host. Add support for reading such an
GPIO in the fixed_phy driver.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the supported field of the phydev to indicate the speed features
of the phy. If the phy is never attached to a netdev, but used in an
adjust_link() function, the speed will be incorrectly evaluated to
10/half rather than the correct speed/duplex.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some Ethernet MAC drivers using the PHY library require the hardcoding
of link parameters when interfaced to a switch device, SFP module,
switch to switch port, etc. This has typically lead to various ad-hoc
implementations looking like this:
- using a "fixed PHY" emulated device, which will provide link
indication towards the Ethernet MAC driver and hardware
- pretend there is no PHY and hardcode link parameters, ala mv643x_eth
Based on that, it is desireable to have the PHY drivers advertise the
correct link parameters, just like regular Ethernet PHYs towards their
CPU Ethernet MAC drivers, however, Ethernet MAC drivers should be able
to tell whether this link should be monitored or not. In the context
of an Ethernet switch, SFP module, switch to switch link, we do not
need to monitor this link since it should be always up.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix scripts/checkpatch.pl's messages like:
CHECK: Comparison to NULL could be written "!phydrv->read_mmd_indirect"
BTW, it doesn't detect the reversed comparisons (which I've fixed as well).
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of the bogus string of type casts where ERR_PTR() is enough.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The fixed link values parsed from the device tree are stored in
the struct fixed_phy member status. The struct phy_device members
speed, duplex were not updated.
Signed-off-by: Madalin Bucur <madalin.bucur@freescale.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phy layer is missing locking for the above two functions - it
has been observed that two threads (userspace and the phy worker
thread) can race, entering the bus ->write or ->read functions
simultaneously.
This causes the FEC driver to initialise a completion while another
thread is waiting on it or while the interrupt is calling complete()
on it, which causes spinlock unlock-without-lock, spinlock lockups,
and completion timeouts.
Fixes: a59a4d192 ("phy: add the EEE support and the way to access to the MMD registers.")
Fixes: 0c1d77dfb ("net: libphy: Add phy specific function to access mmd phy registers")
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 18ee49ddb0 ("phylib: rename mii_bus::dev to mii_bus::parent")
changed the parent of PHY devices from the bus to the bus parent.
Then, commit 4dea547fef ("phylib: rework to prepare for OF
registration of PHYs") moved the code into phy_device.c
At this point, it is somewhat unclear why the change was seen as
necessary. But, when we look at the device model tree in
/sys/devices, it is clearly incorrect. The PHYs should be children of
their MDIO bus.
Change the PHY's parent device to be the MDIO bus device.
Cc: Lennert Buytenhek <buytenh@wantstofly.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: David Daney <david.daney@cavium.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By implementing config_intr & ack_interrupt, now the phy can support
link connect/disconnect interrupt.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* Due to HW bug, LAN8700 sometimes does not detect presence of energy in the
Ethernet cable in Energy Detect Power-Down mode (e.g while EDPWRDOWN bit is
set, the ENERGYON bit does not asserted sometimes). This is a common bug of
LAN87xx family of PHY chips.
* The lan87xx_read_status() was improved to acquire ENERGYON bit. Its previous
algorythm still not reliable on 100 % and sometimes skip cable plugging.
Signed-off-by: Igor Plyatov <plyatov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, if phy state is PHY_RUNNING, we always register a CHANGE
when phy works in polling or interrupt ignored, this will make the
adjust_link being called even the phy link did Not changed.
checking the phy link to make sure the link did changed before we
register a CHANGE, if link did not changed, we do nothing.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the Marvel 88e1111 PHY only two SGMII modes are available, both
allowing only SGMII to copper mode (with or without clock). SGMII
to fiber mode is not supported. Make sure the fiber/copper registers
selector bits are cleared for selecting copper mode.
Signed-off-by: Madalin Bucur <madalin.bucur@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch added driver to support Aquantia PHYs AQ1202, AQ2104, AQR105,
AQR405, which accessed through clause 45.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The change removes redundant sysfs binary file boundary checks,
since this task is already done on caller side in fs/sysfs/file.c
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a possible crash in the octeon_mdiobus_probe function
if the return values are not handled properly.
Signed-off-by: Radha Mohan Chintakuntla <rchintakuntla@cavium.com>
Signed-off-by: Tomasz Nowicki <tomasz.nowicki@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
