Commit Graph

20564 Commits

Author SHA1 Message Date
Bruno Randolf
6665b54e79 ath5k: fix antenna div gc for <= AR5K_SREV_PHY_2413
In commit 39d5b2c83c "ath5k: update
AR5K_PHY_RESTART_DIV_GC values to match masks" i introduced a regression on PHY
chips older than AR5K_SREV_PHY_5413, which caused signal values to be about
10dB less that before. This patch reverts the AR5K_PHY_RESTART_DIV_GC values to
the same values which were effectively used before (without the bitmask
mistake). This brings signal levels back to normal on these PHY chips.

Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-28 15:16:19 -04:00
Magnus Damm
55d02a47de b43: Add SDIO_DEVICE() for EW-CG1102GC
This patch enables the EW-CG1102GC SDIO card in the b43 driver.

b43-sdio mmc0:0001:1: Chip ID 14e4:4318
ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x0D, vendor 0x4243)
ssb: Core 1 found: IEEE 802.11 (cc 0x812, rev 0x09, vendor 0x4243)
ssb: Core 2 found: PCI (cc 0x804, rev 0x0C, vendor 0x4243)
ssb: Core 3 found: PCMCIA (cc 0x80D, rev 0x07, vendor 0x4243)
b43-phy0: Broadcom 4318 WLAN found (core revision 9)
b43-phy0 debug: Found PHY: Analog 3, Type 2, Revision 7
b43-phy0 debug: Found Radio: Manuf 0x17F, Version 0x2050, Revision 8

Tested with openfwwf-5.2 using a SuperH SDHI host controller.

Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-28 15:16:19 -04:00
Wey-Yi Guy
679db79467 iwlwifi: add disable rf calibration support for 6000g2a and 6000g2b
Radio calibration (chain noise and sensitivity) should be allowed to
be disabled from debugfs if compiled with CONFIG_IWLWIFI_DEBUGFS. For both
6000g2a and 6000g2b, the parameters are missing in "cfg", which cause
user can not disable the radio calibration manually; add the support to
allow the operation.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
2010-06-25 15:20:41 -07:00
Reinette Chatre
2b2129f159 iwlagn: reduce severity of disconnected antennas warning
This message is encountered regularly and we need to take a closer look at
the circumstances under which it is printed before presenting errors to
users.

Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
2010-06-25 15:20:41 -07:00
Wey-Yi Guy
cfecc6b492 iwlwifi: turn on RTS/CTS after aggregation become operational
If RTS/CTS protection is needed for HT, wait until get operational
notification from mac80211, then inform uCode to switch to RTS/CTS
through RXON command.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
2010-06-25 15:20:41 -07:00
Johannes Berg
0ab84cff8b iwlwifi: read rfkill during resume
When resuming from hibernate or suspend,
the status of the rfkill switch isn't
known since it might have been toggled
while the system was asleep. Therefore,
we need to read out the status at resume
time to make sure the system knows about
an up-to-date status.

Reported-by: Mark Tung <mark.y.tung@intel.com>
Tested-by: Mark Tung <mark.y.tung@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
2010-06-25 15:20:18 -07:00
Daniel Halperin
278c2f6faa iwlwifi: update LQ for bcast station on channel change
The rate table in the bcast LQ is computed only when the station is
allocated, and chooses the lowest rate for the band. Because of when this
occurs, this is the 2.4 GHz band and uses the 0x420a (CCK, 1 Mbps) rate. In 5 GHz
beaconing mode, this rate will prevent beacons from being sent and any other
packets from being received.

We can fix this by re-initializing the bcast station's LQ command when the
channel is changed.

Signed-off-by: Daniel Halperin <dhalperi@cs.washington.edu>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
2010-06-25 14:53:49 -07:00
Wey-Yi Guy
680788aca3 iwlwifi: add a mechanism to disable plcp error checking
For some devices, especially the upcoming new devices, the plcp error
rate is different. Before the correct error rate can be determine, also
for the debugging purpose; add the mechanism to disable plcp error checking
which cause radio reset happen.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
2010-06-25 14:52:47 -07:00
Wey-Yi Guy
178d159607 iwlwifi: enable DC calibration based on config parameter
Different devices have different calibration requirement,
some need DC calibration and some don't; make it a cfg parameter
for easy management.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
2010-06-25 14:52:18 -07:00
Wey-Yi Guy
4e3243f549 iwlwifi: name change from signal protection flag
This bit need to be set for both RTS/CTS or CTS-to-self protection, if
CTS-to-self is used, then uCode will  check the RXON_FLG_SELF_CTS_EN
status. Change the name from TX_CMD_FLG_RTS_CTS_MSK to TX_CMD_FLAG_PROT_REQUIRE_MSK
to match the behavior of the bit setting.

Also update comments to reflect which hardware uses which of the TX command
flags.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
2010-06-25 14:50:53 -07:00
Reinette Chatre
e691e19e05 Merge branch 'wireless-2.6' into wireless-next-2.6 2010-06-25 14:47:02 -07:00
Wey-Yi Guy
062bee448b iwlwifi: set TX_CMD_FLAG_PROT_REQUIRE_MSK in tx_flag
When building tx command, always set TX_CMD_FLAG_PROT_REQUIRE_MSK
for 5000 series and up.

Without setting this bit the firmware will not examine the RTS/CTS setting
and thus not send traffic with the appropriate protection. RTS/CTS is is
required for HT traffic in a noisy environment where, without this setting,
connections will stall on some hardware as documented in the patch that
initially attempted to address this:

    commit 1152dcc28c
    Author: Wey-Yi Guy <wey-yi.w.guy@intel.com>
    Date:   Fri Jan 15 13:42:58 2010 -0800

    iwlwifi: Fix throughput stall issue in HT mode for 5000

    Similar to 6000 and 1000 series, RTS/CTS is the recommended
    protection mechanism for 5000 series in HT mode based on the HW design.
    Using RTS/CTS will better protect the inner exchange from interference,
    especially in highly-congested environment, it also prevent uCode encounter
    TX FIFO underrun and other HT mode related performance issues.

For 3945 and 4965, different flags are used for RTS/CTS or CTS-to-Self
protection.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
2010-06-25 14:34:45 -07:00
Johannes Berg
d1e89f37de iwlwifi: fix multicast
commit 3474ad635d
Author: Johannes Berg <johannes.berg@intel.com>
Date:   Thu Apr 29 04:43:05 2010 -0700

    iwlwifi: apply filter flags directly

broke multicast. The reason, it turns out, is that
the code previously checked if ALLMULTI _changed_,
which the new code no longer did, and normally it
_never_ changes. Had somebody changed it manually,
the code prior to my patch there would have been
broken already.

The reason is that we always, unconditionally, ask
the device to pass up all multicast frames, but the
new code made it depend on ALLMULTI which broke it
since now we'd pass up multicast frames depending
on the default filter in the device, which isn't
necessarily what we want (since we don't program it
right now).

Fix this by simply not checking allmulti as we have
allmulti behaviour enabled already anyway.

Reported-by: Maxim Levitsky <maximlevitsky@gmail.com>
Tested-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2010-06-25 14:32:06 -07:00
Vasanthakumar Thiagarajan
47399f1a7d ath9k: Wakeup the chip in an appropriate place in ath_paprd_calibrate()
Move ath9k_ps_wakeup() down just before accessing hw registers.

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-24 15:42:43 -04:00
Vasanthakumar Thiagarajan
78a1817251 ath9k: Remove unused paprd_txok
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-24 15:42:42 -04:00
Vasanthakumar Thiagarajan
ca369eb494 ath9k: Fix bug in paprd
It is possbile that the transmission of paprd test frame
might not get completed in 100ms if tx is stuck. Freeing
this skb upon timeout in ath_paprd_calibrate() will result
in accessing already freed memory when the associated pending
buffer is drained in txq. This patch fixes this issue.

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-24 15:42:39 -04:00
Ondrej Zary
75f64dd54a rt2500usb: fallback to SW encryption for TKIP+AES
HW crypto in rt2500usb does not seem to support keys with different ciphers,
which breaks TKIP+AES mode. Fall back to software encryption to fix it.

This should fix long-standing problems with rt2500usb and WPA, such as:
http://rt2x00.serialmonkey.com/phpBB/viewtopic.php?f=4&t=4834
https://bugzilla.redhat.com/show_bug.cgi?id=484888

Also tested that it does not break WEP, TKIP-only and AES-only modes.

Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-24 15:42:38 -04:00
Juuso Oikarinen
fa61cf70a6 cfg80211/mac80211: Update set_tx_power to use mBm instead of dBm units
In preparation for a TX power setting interface in the nl80211, change the
.set_tx_power function to use mBm units instead of dBm for greater accuracy and
smaller power levels.

Also, already in advance move the tx_power_setting enumeration to nl80211.

This change affects the .tx_set_power function prototype. As a result, the
corresponding changes are needed to modules using it. These are mac80211,
iwmc3200wifi and rndis_wlan.

Cc: Samuel Ortiz <samuel.ortiz@intel.com>
Cc: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Acked-by: Samuel Ortiz <samuel.ortiz@intel.com>
Acked-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-24 15:42:33 -04:00
Sebastian Smolorz
a185045c8d at76c50x-usb: Extract bssid from authentication frame
The driver at76c50x-usb is unable to authenticate with an AP since
kernel 2.6.31 for the following reason: The join command of the firmware
needs to be sent with the right bssid before any transmission can start.
Before kernel 2.6.31 mac80211 informed its drivers about the changing
bssid early enough for at76c50x-usb but during the development of 2.6.31
mac80211's behaviour changed. Now a new bssid is set after the
association.

This patch changes the tx routine of the driver at76c50x-usb in such a
way that a new bssid is extracted from an authentication frame and the
join command with that bssid is processed.

Signed-off-by: Sebastian Smolorz <sesmo@gmx.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-24 15:42:33 -04:00
Sebastian Smolorz
41b4b289ad at76c50x-usb: Move function at76_join() several lines up
This patch does a simple code move of at76_join() so that
at76_mac80211_tx() follows at76_join() in the driver's source file.

This is a preparatory patch for the following patch where we need
to call at76_join() from at76_mac80211_tx() in order to
authenticate successfully with a bssid.

Signed-off-by: Sebastian Smolorz <sesmo@gmx.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-24 15:42:32 -04:00
John W. Linville
a3275e24aa rtl8180: mark rtl8180_beacon_work static
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-24 11:08:37 -04:00
Vasanthakumar Thiagarajan
6c3118e230 ath9k: Fix bug in starting ani
There are few places where ANI is started without checking
if it is right to start. This might lead to a case where ani
timer would be left undeleted and cause improper memory acccess
during module unload. This bug is clearly exposed with
paprd support where the driver detects tx hang and does a
chip reset. During this reset ani is (re)started without checking
if it needs to be started. This would leave a timer scheduled
even after all the resources are freed and cause a panic.

This patch introduces a bit in sc_flags to indicate if ani
needs to be started in sw_scan_start() and ath_reset().
This would fix the following panic. This issue is easily seen
with ar9003 + paprd.

 BUG: unable to handle kernel paging request at 0000000000003f38
[<ffffffff81075391>] ? __queue_work+0x41/0x50
[<ffffffff8106afaa>] run_timer_softirq+0x17a/0x370
[<ffffffff81088be8>] ? tick_dev_program_event+0x48/0x110
[<ffffffff81061f69>] __do_softirq+0xb9/0x1f0
[<ffffffff810ba060>] ? handle_IRQ_event+0x50/0x160
[<ffffffff8100af5c>] call_softirq+0x1c/0x30
[<ffffffff8100c9f5>] do_softirq+0x65/0xa0
[<ffffffff81061e25>] irq_exit+0x85/0x90
[<ffffffff8155e095>] do_IRQ+0x75/0xf0
[<ffffffff815570d3>] ret_from_intr+0x0/0x11
<EOI>
[<ffffffff812fd67b>] ? acpi_idle_enter_simple+0xe4/0x119
[<ffffffff812fd674>] ? acpi_idle_enter_simple+0xdd/0x119
[<ffffffff81441c87>] cpuidle_idle_call+0xa7/0x140
[<ffffffff81008da3>] cpu_idle+0xb3/0x110
[<ffffffff81550722>] start_secondary+0x1ee/0x1f5

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-23 15:28:42 -04:00
John W. Linville
d0ee0ebe17 ath9k: declare MODULE_FIRMWARE for ath9k_htc
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-23 15:14:07 -04:00
John W. Linville
25ac8b0d06 libertas: mark lbs_ret_802_11d_domain_info static
Probably little risk of namespace polution, but good practice... :-)

Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-23 15:14:06 -04:00
Vivek Natarajan
9a75c2ff6d ath9k: Add a module parameter to disable led blinking.
Some vendors require the LED to be ON always irrespective of any
radio activity. Introducing a module parameter to disable blinking,
so that one can choose between always on or led blink during
activity.

Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-23 15:14:05 -04:00
Luis R. Rodriguez
ee031112d9 ath9k_hw: add an extra delay when reseting AR_RTC_RESET
Without this we could start trying to work with the device without
it being fully functional yet and loose some packets upon resume.

Cc: Aeolus Yang <aeolus.yang@atheros.com>
Cc: Madhan Jaganathan <madhan.jaganathan@atheros.com>
signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>

Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-23 15:14:04 -04:00
Luis R. Rodriguez
d5c4d1930c ath9k_hw: dynamically choose the SERDES array for low power
The array we use will vary depending on whether or not we are
to go to lower power or not. The default values (iniPcieSerdes)
are a copy or what go into the registers through the INI files.

Cc: Aeolus Yang <aeolus.yang@atheros.com>
Cc: Madhan Jaganathan <madhan.jaganathan@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-23 15:14:03 -04:00
Luis R. Rodriguez
6a0ec30ad4 ath9k_hw: add pcieSerDesWrite to disable SERDES ASPM tweaks
This can be useful during testing of new ASPM tweaks which often
have to be done through the PCI Serializer-Deserializer (SERDES).

Cc: Aeolus Yang <aeolus.yang@atheros.com>
Cc: Madhan Jaganathan <madhan.jaganathan@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-23 15:14:02 -04:00
Luis R. Rodriguez
653fe37122 ath9k_hw: move LowPower array writes to ar9003_hw_configpcipowersave()
The LowPower array writes disables the PLL when ASPM is enabled.
The host driver makes quite a few calls to ath9k_hw_configpcipowersave()
and these same calls also need to ensure the PLL is off when they issue
it.

Cc: Aeolus Yang <aeolus.yang@atheros.com>
Cc: Madhan Jaganathan <madhan.jaganathan@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-23 15:14:01 -04:00
Luis R. Rodriguez
9a658d2b5c ath9k_hw: fix ASPM setting for AR9003
The AR_WA register should not be read when in sleep state so
add a variable we can stash its value into for when we need
to set it. Additionally the AR_WA_D3_TO_L1_DISABLE_REAL
(bit 16) needs to be removed.

Cc: Aeolus Yang <aeolus.yang@atheros.com>
Cc: Madhan Jaganathan <madhan.jaganathan@atheros.com>
signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>

Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-23 15:14:00 -04:00
Kiran Divekar
1047d5edd4 Libertas: Added 11d support using cfg80211
Added 11d support for libertas driver using cfg80211. This is based on Holger
Shurig's initial work to add cfg80211 support libertas.
(https://patchwork.kernel.org/patch/64286/)

Please let us know, if there are any improvements comments.

Code is added to send 11d enable command to firmware while
initialisation and pass 11d specific information to firmware
when notifier handler is called by cfg80211.

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-23 15:14:00 -04:00
Kiran Divekar
e4fe4eafa4 Libertas: fix WARN_ON issues in cfg80211 support
In following scenarios WARN_ON() in cfg80211 code was triggered.
a) Driver unload or card removal.
b) Disconnect from infra network
c) Adhoc start/join
d) Adhoc stop
Added following fixes to avoid WARN_ON() in cfg80211 code.
a) Ensured that cfg80211_disconnected() function defined in cfg80211
code will be called only in infra mode.
b) Solved timing issue by moving cfg80211_disconnected() call inside
lbs_cfg_disconnect().
c) Updated "wdev->ssid" in driver code after Adhoc join/start
d) Removed unnecessory cfg80211_disconnected() call in lbs_remove_card.

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-23 15:13:59 -04:00
Kiran Divekar
e86dc1ca46 Libertas: cfg80211 support
Holger Schurig's patch (https://patchwork.kernel.org/patch/64286/)
is rebased to latest wireless-testing tree.

(Includes patches from me originally posted as "libertas: fix build
error due to undefined symbol" and "libertas: unmangle capability
value". -- JWL)

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Tested-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-23 15:13:11 -04:00
Larry Finger
bb64d95e53 b43: Clarify logged message after fatal DMA error and switch to PIO mode
The message following fatal DMA errors fails to indicate properly that the
driver has switched to PIO mode.

Signed-off-by: Larry Finger <Larry.Finger@wfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-21 15:39:59 -04:00
Wey-Yi Guy
051cb98686 iwlwifi: remove non-exist reference
Remove the reference to non-exist function in iwlcore

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
2010-06-21 10:47:45 -07:00
Wey-Yi Guy
936e8a734f iwlwifi: code cleanup to remove un-necessary "goto"
Break out of loop and log the error message when encounter error; this is
better approach than using "goto".

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
2010-06-21 10:47:39 -07:00
Wey-Yi Guy
f84ac08db2 iwlwifi: move calibration from iwlcore to iwlagn
All the calibrations are "agn" only functions, move from iwlcore to
iwlagn.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
2010-06-21 10:47:32 -07:00
Wey-Yi Guy
f3aebeeebc iwlwifi: move _agn statistics related structure
agn and 3945 has different statistics_notif data structure; since 3945
has it statistics_notif data structure inside the _3945 portion of
iwl_priv, it make sense to move the agn statistics_notif into _agn
portion.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
2010-06-21 10:47:25 -07:00
Wey-Yi Guy
278fc73c0c iwlwifi: move agn specific rx related code to iwl-agn-rx.c
To avoid having unnecessary functions in iwlcore.ko, those that
are not shared by agn and 3945, move agn specific rx related code
to iwl-agn-rx.c.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
2010-06-21 10:47:12 -07:00
Jay Sternberg
8756371589 iwlwifi: display ucode SW Error in hex
errors are defined in hex but displayed as decimal.  displaying as hex
debugging easier and eliminated having to manually convert.

Signed-off-by: Jay Sternberg <jay.e.sternberg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
2010-06-21 10:47:03 -07:00
Johannes Berg
09034cb77e iwlwifi: return ucode errors from station management
When station management calls to ucode return
an error we could previously do nothing, but
now that almost all calls are synchronous we
can actually let the error bubble up. Use EIO
as the error as it best indicates a problem
with the device.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
2010-06-21 10:46:50 -07:00
Johannes Berg
e666674eec iwlwifi: use sync commands for keys
Key management can use sync commands
instead of asynchronous ones to have
better error checking.

Also add checks that the commands all
should have the mutex held.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
2010-06-21 10:46:37 -07:00
Johannes Berg
4620fefa59 iwlagn: use mutex for aggregation
Now that the ampdu_action callback can sleep,
we can use the mutex to properly protect the
aggregation data, and return useful errors if
they should happen.

Also, add some sleep and mutex debugging so
we won't call any of the functions that now
require being able to sleep and/or the mutex
to be held in an invalid context.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
2010-06-21 10:46:21 -07:00
Johannes Berg
8223d2f540 mac80211_hwsim: fix fake_hw_scan
Since mac80211 will not set the max_scan parameters
if hw scan is enabled, hwsim needs to do it so that
cfg80211 won't reject the scan.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-18 15:11:14 -04:00
Sujith
4e63f768c3 ath9k_htc: Update supported product list
This patch adds USB IDs for some more supported
devices.

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-18 15:05:12 -04:00
Justin P. Mattock
1baf8a90bd wireless:hostap_ap.c Fix warning: variable 'fc' set but not used
The below patch fixes a warning message when compiling with gcc 4.6.0
  CC [M]  drivers/net/wireless/hostap/hostap_ap.o
drivers/net/wireless/hostap/hostap_ap.c: In function 'hostap_ap_tx_cb_assoc':
drivers/net/wireless/hostap/hostap_ap.c:691:6: warning: variable 'fc' set but not used

 Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>

Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-18 15:05:12 -04:00
Justin P. Mattock
deda484cd7 wireless:hostap_main.c warning: variable 'iface' set but not used
The patch below fixes a warning message Im seeing with gcc 4.6.0
 CC [M]  drivers/net/wireless/hostap/hostap_main.o
drivers/net/wireless/hostap/hostap_main.c: In function 'hostap_set_multicast_list_queue':
drivers/net/wireless/hostap/hostap_main.c:744:27: warning: variable 'iface' set but not used

 Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>

Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-18 15:05:11 -04:00
Bob Copeland
b6855772f4 ath5k: initialize ah->ah_current_channel
ath5k assumes ah_current_channel is always a valid pointer in
several places, but a newly created interface may not have a
channel.  To avoid null pointer dereferences, set it up to point
to the first available channel until later reconfigured.

This fixes the following oops:
$ rmmod ath5k
$ insmod ath5k
$ iw phy0 set distance 11000

BUG: unable to handle kernel NULL pointer dereference at 00000006
IP: [<d0a1ff24>] ath5k_hw_set_coverage_class+0x74/0x1b0 [ath5k]
*pde = 00000000
Oops: 0000 [#1]
last sysfs file: /sys/devices/pci0000:00/0000:00:0e.0/ieee80211/phy0/index
Modules linked in: usbhid option usb_storage usbserial usblp evdev lm90
scx200_acb i2c_algo_bit i2c_dev i2c_core via_rhine ohci_hcd ne2k_pci
8390 leds_alix2 xt_IMQ imq nf_nat_tftp nf_conntrack_tftp nf_nat_irc nf_cc

Pid: 1597, comm: iw Not tainted (2.6.32.14 #8)
EIP: 0060:[<d0a1ff24>] EFLAGS: 00010296 CPU: 0
EIP is at ath5k_hw_set_coverage_class+0x74/0x1b0 [ath5k]
EAX: 000000c2 EBX: 00000000 ECX: ffffffff EDX: c12d2080
ESI: 00000019 EDI: cf8c0000 EBP: d0a30edc ESP: cfa09bf4
  DS: 007b ES: 007b FS: 0000 GS: 0000 SS: 0068
Process iw (pid: 1597, ti=cfa09000 task=cf88a000 task.ti=cfa09000)
Stack:
  d0a34f35 d0a353f8 d0a30edc 000000fe cf8c0000 00000000 1900063d cfa8c9e0
<0> cfa8c9e8 cfa8c0c0 cfa8c000 d0a27f0c 199d84b4 cfa8c200 00000010 d09bfdc7
<0> 00000000 00000000 ffffffff d08e0d28 cf9263c0 00000001 cfa09cc4 00000000
Call Trace:
  [<d0a27f0c>] ? ath5k_hw_attach+0xc8c/0x3c10 [ath5k]
  [<d09bfdc7>] ? __ieee80211_request_smps+0x1347/0x1580 [mac80211]
  [<d08e0d28>] ? nl80211_send_scan_start+0x7b8/0x4520 [cfg80211]
  [<c10f5db9>] ? nla_parse+0x59/0xc0
  [<c11ca8d9>] ? genl_rcv_msg+0x169/0x1a0
  [<c11ca770>] ? genl_rcv_msg+0x0/0x1a0
  [<c11c7e68>] ? netlink_rcv_skb+0x38/0x90
  [<c11c9649>] ? genl_rcv+0x19/0x30
  [<c11c7c03>] ? netlink_unicast+0x1b3/0x220
  [<c11c893e>] ? netlink_sendmsg+0x26e/0x290
  [<c11a409e>] ? sock_sendmsg+0xbe/0xf0
  [<c1032780>] ? autoremove_wake_function+0x0/0x50
  [<c104d846>] ? __alloc_pages_nodemask+0x106/0x530
  [<c1074933>] ? do_lookup+0x53/0x1b0
  [<c10766f9>] ? __link_path_walk+0x9b9/0x9e0
  [<c11acab0>] ? verify_iovec+0x50/0x90
  [<c11a42b1>] ? sys_sendmsg+0x1e1/0x270
  [<c1048e50>] ? find_get_page+0x10/0x50
  [<c104a96f>] ? filemap_fault+0x5f/0x370
  [<c1059159>] ? __do_fault+0x319/0x370
  [<c11a55b4>] ? sys_socketcall+0x244/0x290
  [<c101962c>] ? do_page_fault+0x1ec/0x270
  [<c1019440>] ? do_page_fault+0x0/0x270
  [<c1002ae5>] ? syscall_call+0x7/0xb
Code: 00 b8 fe 00 00 00 b9 f8 53 a3 d0 89 5c 24 14 89 7c 24 10 89 44 24
0c 89 6c 24 08 89 4c 24 04 c7 04 24 35 4f a3 d0 e8 7c 30 60 f0 <0f> b7
43 06 ba 06 00 00 00 a8 10 75 0e 83 e0 20 83 f8 01 19 d2
EIP: [<d0a1ff24>] ath5k_hw_set_coverage_class+0x74/0x1b0 [ath5k] SS:ESP
0068:cfa09bf4
CR2: 0000000000000006
---[ end trace 54f73d6b10ceb87b ]---

Cc: stable@kernel.org
Reported-by: Steve Brown <sbrown@cortland.com>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-18 14:59:10 -04:00
John W. Linville
abf52f86aa Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
Conflicts:
	net/mac80211/mlme.c
2010-06-17 16:21:14 -04:00
Bruno Randolf
6a0076e02a ath5k: report PHY error frames only for chips which need it
Only report PHY error frames for ANI on chipsets which do not have PHY error
counters in hardware.

Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-16 14:59:07 -04:00