Fifo thresholds for all pipelines are set in dispc_init_fifos(), but we
are missing it for WB pipeline. Add that.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Burst size for all pipelines is set in dispc_configure_burst_sizes(),
but we are missing WB pipe. So add that.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add handling of OMAP_DSS_CHANNEL_WB to dispc_ovl_set_channel_out() and
dispc_ovl_get_channel_out().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Refactor dispc_ovl_get_channel_out() to a bit cleaner form, which makes
it easier to add support for writeback in the following patch.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
At the moment we have a function to get the number of writeback
pipelines supported. However, the function is used in a wrong way,
causing a wrong pipeline to get configured when trying to use WB. Also,
we only have a single writeback pipeline on any of the DSS versions.
To fix and simplify this, create a 'has_writeback' flag into the dispc
driver, and after checking the flag, use OMAP_DSS_WB pipeline
explicitly when calling the configuration functions.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
OMAP5+ DSS has a writeback pipeline, but this was not specified in the
features list for OMAP5 DSS.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
By default DISPC asserts hsync and vsync sequentially, i.e. there's
first hsync and that is immediately followed by vsync. This is the only
available behaviour on OMAP2/3, and default behaviour on OMAP4+.
OMAP4+ has ALIGN bit in POL_FREQ register, which makes DISPC assert both
syncs at the same time.
It has been observed that some panels don't like sequential syncs (AM5
EVM's panel). After studying the datasheets for multiple panels and
encoders, and MIPI DPI spec, it looks like there is no standard way to
handle this.
Sometimes the datasheets don't mention the required syncs behaviour at
all, sometimes the datasheets have images that hint towards simultaneous
syncs, and sometimes it is explicitly mentioned that simultaneous syncs
are needed. No panels or encoders requiring sequential sync was found.
It thus seems to be safe to default to simultaneous syncs when the ALIGN
bit is available. This fixed AM5 EVM's panel, and no side effects have
been observed on other panels or encoders.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Update omapdss driver to set the state of the pins to:
- "default on resume
- "sleep" on suspend
By optionally putting the pins into sleep state in the suspend callback
we can accomplish two things.
- minimize current leakage from pins and thus save power,
- prevent the IP from driving pins output in an uncontrolled manner,
which may happen if the power domain drops the domain regulator.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This patch brings a first support of pxa framebuffer devices to a
devicetree pxa platform, as was before platform data.
There are restrictions with this port, the biggest one being the lack of
support of smart panels. Moreover the conversion doesn't provide a way
to declare multiple framebuffer configurations with different bits per
pixel, only the LCD hardware bus width is used.
The patch was tested on both pxa25x, pxa27x and pxa3xx platform (namely
lubbock, mainstone and zylonite).
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
In order to prepare the transition to a mixed platform data and
device-tree initialization, remove all the platform data references all
over the driver.
Copy the platform data into the internal structure of the pxafb, and
only use this afterward.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
There's no point in having support for framebuffer notifications
is CONFIG_FB is disabled. This commit adds the necessary stubs
for code to link properly when CONFIG_FB=n and moves fb-notify.o
to be built only when CONFIG_FB=y.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
When the usual fbcon legacy options are enabled we have
->register_framebuffer
->fb notifier chain calls into fbcon
->fbcon sets up console on new fbi
->fbi->set_par
->drm_fb_helper_set_par exercises full kms api
And because of locking inversion hilarity all of register_framebuffer
is done with the console lock held. Which means that the first time on
driver load we exercise _all_ the kms code (all probe paths and
modeset paths for everything connected) is under the console lock.
That means if anything goes belly-up in that big pile of code nothing
ever reaches logfiles (and the machine is dead).
Usual tactic to debug that is to temporarily remove those console_lock
calls to be able to capture backtraces. I'm fed up writing this patch
and recompiling kernels. Hence this patch here to add an unsafe,
kernel-taining option to do this at runtime.
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: linux-fbdev@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
At least NV3 requires for chip to be unlocked before it is possible to
access I2C registers. Without it, it is not possible to read EDID.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The sm712fb framebuffer driver encloses the power-management
functions in #ifdef CONFIG_PM, but the smtcfb_pci_suspend/resume
functions are only really used when CONFIG_PM_SLEEP is also
set, as a frequent gcc warning shows:
fbdev/sm712fb.c:1549:12: warning: 'smtcfb_pci_suspend' defined but not used
fbdev/sm712fb.c:1572:12: warning: 'smtcfb_pci_resume' defined but not used
The driver also avoids using the SIMPLE_DEV_PM_OPS macro when
CONFIG_PM is unset, which is redundant.
This changes the driver to remove the #ifdef and instead mark
the functions as __maybe_unused, which is a nicer anyway, as it
provides build testing for all the code in all configurations
and is harder to get wrong.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The auo_k190x framebuffer driver encloses the power-management
functions in #ifdef CONFIG_PM, but the auok190x_suspend/resume
functions are only really used when CONFIG_PM_SLEEP is also
set, as a frequent gcc warning shows:
drivers/video/fbdev/auo_k190x.c:859:12: warning: 'auok190x_suspend' defined but not used
drivers/video/fbdev/auo_k190x.c:899:12: warning: 'auok190x_resume' defined but not used
This changes the driver to remove the #ifdef and instead mark
the functions as __maybe_unused, which is a nicer anyway, as it
provides build testing for all the code in all configurations
and is harder to get wrong.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The sis framebuffer driver complains with a compile-time warning
if neither the FB_SIS_300 nor FB_SIS_315 symbols are selected:
drivers/video/fbdev/sis/sis_main.c:61:2: warning: #warning Neither CONFIG_FB_SIS_300 nor CONFIG_FB_SIS_315 is se
This is reasonable because it doesn't work in that case, but it's
also annoying for randconfig builds and is one of the most common
warnings I'm seeing on ARM now.
This changes the Kconfig logic to prevent the silly configuration,
by always selecting the FB_SIS_300 variant if the other one is
not set.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
As of commit 44d88c754e ("ARM: shmobile: Remove legacy SoC code
for R-Mobile A1"), the SH-Mobile HDMI driver is no longer used.
In theory it could still be used on R-Mobile A1 SoCs, but that requires
adding DT support to the driver, which is not planned.
Remove the driver, it can be resurrected from git history when needed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
These geode ops structures are never modified, so declare them as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This claims and enables regulators listed in the simple framebuffer dt
node. This is needed so that regulators powering the display pipeline
and external hardware, described in the device node and known by the
kernel code, will remain properly enabled.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The value of d_best is always 0 and never changes.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
__GFP_WAIT has been used to identify atomic context in callers that hold
spinlocks or are in interrupts. They are expected to be high priority and
have access one of two watermarks lower than "min" which can be referred
to as the "atomic reserve". __GFP_HIGH users get access to the first
lower watermark and can be called the "high priority reserve".
Over time, callers had a requirement to not block when fallback options
were available. Some have abused __GFP_WAIT leading to a situation where
an optimisitic allocation with a fallback option can access atomic
reserves.
This patch uses __GFP_ATOMIC to identify callers that are truely atomic,
cannot sleep and have no alternative. High priority users continue to use
__GFP_HIGH. __GFP_DIRECT_RECLAIM identifies callers that can sleep and
are willing to enter direct reclaim. __GFP_KSWAPD_RECLAIM to identify
callers that want to wake kswapd for background reclaim. __GFP_WAIT is
redefined as a caller that is willing to enter direct reclaim and wake
kswapd for background reclaim.
This patch then converts a number of sites
o __GFP_ATOMIC is used by callers that are high priority and have memory
pools for those requests. GFP_ATOMIC uses this flag.
o Callers that have a limited mempool to guarantee forward progress clear
__GFP_DIRECT_RECLAIM but keep __GFP_KSWAPD_RECLAIM. bio allocations fall
into this category where kswapd will still be woken but atomic reserves
are not used as there is a one-entry mempool to guarantee progress.
o Callers that are checking if they are non-blocking should use the
helper gfpflags_allow_blocking() where possible. This is because
checking for __GFP_WAIT as was done historically now can trigger false
positives. Some exceptions like dm-crypt.c exist where the code intent
is clearer if __GFP_DIRECT_RECLAIM is used instead of the helper due to
flag manipulations.
o Callers that built their own GFP flags instead of starting with GFP_KERNEL
and friends now also need to specify __GFP_KSWAPD_RECLAIM.
The first key hazard to watch out for is callers that removed __GFP_WAIT
and was depending on access to atomic reserves for inconspicuous reasons.
In some cases it may be appropriate for them to use __GFP_HIGH.
The second key hazard is callers that assembled their own combination of
GFP flags instead of starting with something like GFP_KERNEL. They may
now wish to specify __GFP_KSWAPD_RECLAIM. It's almost certainly harmless
if it's missed in most cases as other activity will wake kswapd.
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Christoph Lameter <cl@linux.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Vitaly Wool <vitalywool@gmail.com>
Cc: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Quite a lot of activity in SPI this cycle, almost all of it in drivers
with a few minor improvements and tweaks in the core.
- Updates to pxa2xx to support Intel Broxton and multiple chip selects.
- Support for big endian in the bcm63xx driver.
- Multiple slave support for the mt8173
- New driver for the auxiliary SPI controller in bcm2835 SoCs.
- Support for Layerscale SoCs in the Freescale DSPI driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWOehzAAoJECTWi3JdVIfQTPYH+wYMDG8gAIw2s0AJ4DvVe4qZ
sOAm1UgUJZxssrEA6BNqbfM0dfRo+oQJKmRd0Dc5n7LEMsYHdI/5yKHk8PCS6ZzD
iQyQCzbd0thDAqwuPaMP62cyPDHwyJX22VGTsgVnj6AZqAQ+9+g4SPKhFnm1Mlm4
hmDi6fdSrsqo8k8gkpVN8RFOfVsjAV1dLtAauQRWDHrqMxXURSrKG76eqAqUa5bn
BLPXBoj5PA0DMLPO2j+ADZwWN723LrI2mSSlc+ThjEX/OIt2OhAoiOTV5RPqaafy
TIsCkh68q/gYAsL5HtvvmgZByl41FLYiO0Z+rXmWUyMMbnvhZTLws9S2BNpBLuk=
=DgXG
-----END PGP SIGNATURE-----
Merge tag 'spi-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"Quite a lot of activity in SPI this cycle, almost all of it in drivers
with a few minor improvements and tweaks in the core.
- Updates to pxa2xx to support Intel Broxton and multiple chip selects.
- Support for big endian in the bcm63xx driver.
- Multiple slave support for the mt8173
- New driver for the auxiliary SPI controller in bcm2835 SoCs.
- Support for Layerscale SoCs in the Freescale DSPI driver"
* tag 'spi-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (87 commits)
spi: pxa2xx: Rework self-initiated platform data creation for non-ACPI
spi: pxa2xx: Add support for Intel Broxton
spi: pxa2xx: Detect number of enabled Intel LPSS SPI chip select signals
spi: pxa2xx: Add output control for multiple Intel LPSS chip selects
spi: pxa2xx: Use LPSS prefix for defines that are Intel LPSS specific
spi: Add DSPI support for layerscape family
spi: ti-qspi: improve ->remove() callback
spi/spi-xilinx: Fix race condition on last word read
spi: Drop owner assignment from spi_drivers
spi: Add THIS_MODULE to spi_driver in SPI core
spi: Setup the master controller driver before setting the chipselect
spi: dw: replace magic constant by DW_SPI_DR
spi: mediatek: mt8173 spi multiple devices support
spi: mediatek: handle controller_data in mtk_spi_setup
spi: mediatek: remove mtk_spi_config
spi: mediatek: Update document devicetree bindings to support multiple devices
spi: fix kernel-doc warnings about missing return desc in spi.c
spi: fix kernel-doc warnings about missing return desc in spi.h
spi: pxa2xx: Align a few defines
spi: pxa2xx: Save other reg_cs_ctrl bits when configuring chip select
...
Pull EFI changes from Ingo Molnar:
"The main changes in this cycle were:
- further EFI code generalization to make it more workable for ARM64
- various extensions, such as 64-bit framebuffer address support,
UEFI v2.5 EFI_PROPERTIES_TABLE support
- code modularization simplifications and cleanups
- new debugging parameters
- various fixes and smaller additions"
* 'core-efi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (23 commits)
efi: Fix warning of int-to-pointer-cast on x86 32-bit builds
efi: Use correct type for struct efi_memory_map::phys_map
x86/efi: Fix kernel panic when CONFIG_DEBUG_VIRTUAL is enabled
efi: Add "efi_fake_mem" boot option
x86/efi: Rename print_efi_memmap() to efi_print_memmap()
efi: Auto-load the efi-pstore module
efi: Introduce EFI_NX_PE_DATA bit and set it from properties table
efi: Add support for UEFIv2.5 Properties table
efi: Add EFI_MEMORY_MORE_RELIABLE support to efi_md_typeattr_format()
efifb: Add support for 64-bit frame buffer addresses
efi/arm64: Clean up efi_get_fdt_params() interface
arm64: Use core efi=debug instead of uefi_debug command line parameter
efi/x86: Move efi=debug option parsing to core
drivers/firmware: Make efi/esrt.c driver explicitly non-modular
efi: Use the generic efi.memmap instead of 'memmap'
acpi/apei: Use appropriate pgprot_t to map GHES memory
arm64, acpi/apei: Implement arch_apei_get_mem_attributes()
arm64/mm: Add PROT_DEVICE_nGnRnE and PROT_NORMAL_WT
acpi, x86: Implement arch_apei_get_mem_attributes()
efi, x86: Rearrange efi_mem_attributes()
...
Default the brightness to 2048 and add possibility to override this in
device tree.
Suggested-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
An spi_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
drivers/video/backlight/pm8941-wled.c:404:1-3: WARNING: PTR_ERR_OR_ZERO can be used
Use PTR_ERR_OR_ZERO rather than if(IS_ERR(...)) + PTR_ERR
Generated by: scripts/coccinelle/api/ptr_ret.cocci
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Since commit 27a4c827c3
fbcon: use the cursor blink interval provided by vt
a PPC64LE kernel fails to boot when fbcon_add_cursor_timer uses an
uninitialized ops->cur_blink_jiffies. Prevent by initializing
in fbcon_init before the call to info->fbops->fb_set_par.
Reported-and-tested-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Scot Doyle <lkml14@scotdoyle.com>
Cc: <stable@vger.kernel.org> [v4.2]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Platform PWM backlight data provided by board's device tree should be
complete enough to successfully request a pwm device using pwm_get()
API. This change fixes a bug, when an arbitrary (first found) PWM is
connected to a "pwm-backlight" compatible device, when explicit PWM
device reference is not given.
Documentation/devicetree/bindings/video/backlight/pwm-backlight.txt
already describes "pwms" as a required property, instead of blind
selection of a potentially wrong PWM reject legacy PWM device
registration request, leave legacy API only for non-dt cases.
Based on initial implementation done by Dmitry Eremin-Solenikov.
Reported-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
for_each_child_of_node performs an of_node_get on each iteration, so
a break out of the loop requires an of_node_put.
The semantic patch that fixes this problem is as follows
(http://coccinelle.lip6.fr):
// <smpl>
@@
expression root,e;
local idexpression child;
iterator name for_each_child_of_node;
@@
for_each_child_of_node(root, child) {
... when != of_node_put(child)
when != e = child
+ of_node_put(child);
? break;
...
}
... when != child
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
non-modular by ripping out the module_* code since Kconfig doesn't
allow it to be built as a module anyway - Paul Gortmaker
* Make the x86 efi=debug kernel parameter, which enables EFI debug
code and output, generic and usable by arm64 - Leif Lindholm
* Add support to the x86 EFI boot stub for 64-bit Graphics Output
Protocol frame buffer addresses - Matt Fleming
* Detect when the UEFI v2.5 EFI_PROPERTIES_TABLE feature is enabled
in the firmware and set an efi.flags bit so the kernel knows when
it can apply more strict runtime mapping attributes - Ard Biesheuvel
* Auto-load the efi-pstore module on EFI systems, just like we
currently do for the efivars module - Ben Hutchings
* Add "efi_fake_mem" kernel parameter which allows the system's EFI
memory map to be updated with additional attributes for specific
memory ranges. This is useful for testing the kernel code that handles
the EFI_MEMORY_MORE_RELIABLE memmap bit even if your firmware
doesn't include support - Taku Izumi
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=1Oee
-----END PGP SIGNATURE-----
Merge tag 'efi-next' of git://git.kernel.org/pub/scm/linux/kernel/git/mfleming/efi into core/efi
Pull v4.4 EFI updates from Matt Fleming:
- Make the EFI System Resource Table (ESRT) driver explicitly
non-modular by ripping out the module_* code since Kconfig doesn't
allow it to be built as a module anyway. (Paul Gortmaker)
- Make the x86 efi=debug kernel parameter, which enables EFI debug
code and output, generic and usable by arm64. (Leif Lindholm)
- Add support to the x86 EFI boot stub for 64-bit Graphics Output
Protocol frame buffer addresses. (Matt Fleming)
- Detect when the UEFI v2.5 EFI_PROPERTIES_TABLE feature is enabled
in the firmware and set an efi.flags bit so the kernel knows when
it can apply more strict runtime mapping attributes - Ard Biesheuvel
- Auto-load the efi-pstore module on EFI systems, just like we
currently do for the efivars module. (Ben Hutchings)
- Add "efi_fake_mem" kernel parameter which allows the system's EFI
memory map to be updated with additional attributes for specific
memory ranges. This is useful for testing the kernel code that handles
the EFI_MEMORY_MORE_RELIABLE memmap bit even if your firmware
doesn't include support. (Taku Izumi)
Note: there is a semantic conflict between the following two commits:
8a53554e12 ("x86/efi: Fix multiple GOP device support")
ae2ee627dc ("efifb: Add support for 64-bit frame buffer addresses")
I fixed up the interaction in the merge commit, changing the type of
current_fb_base from u32 to u64.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The EFI Graphics Output Protocol uses 64-bit frame buffer addresses
but these get truncated to 32-bit by the EFI boot stub when storing
the address in the 'lfb_base' field of 'struct screen_info'.
Add a 'ext_lfb_base' field for the upper 32-bits of the frame buffer
address and set VIDEO_TYPE_CAPABILITY_64BIT_BASE when the field is
useable.
It turns out that the reason no one has required this support so far
is that there's actually code in tianocore to "downgrade" PCI
resources that have option ROMs and 64-bit BARS from 64-bit to 32-bit
to cope with legacy option ROMs that can't handle 64-bit addresses.
The upshot is that basically all GOP devices in the wild use a 32-bit
frame buffer address.
Still, it is possible to build firmware that uses a full 64-bit GOP
frame buffer address. Chad did, which led to him reporting this issue.
Add support in anticipation of GOP devices using 64-bit addresses more
widely, and so that efifb works out of the box when that happens.
Reported-by: Chad Page <chad.page@znyx.com>
Cc: Pete Hawkins <pete.hawkins@znyx.com>
Acked-by: Peter Jones <pjones@redhat.com>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
With this .config: http://busybox.net/~vda/kernel_config,
after uninlining these functions have sizes and callsite counts
as follows:
__OUTPLLP: 61 bytes, 12 callsites
__INPLL: 79 bytes, 150 callsites
__OUTPLL: 82 bytes, 138 callsites
_OUTREGP: 101 bytes, 8 callsites
_radeon_msleep: 66 bytes, 18 callsites
_radeon_fifo_wait: 83 bytes, 24 callsites
_radeon_engine_idle: 92 bytes, 10 callsites
radeon_engine_flush: 105 bytes, 2 callsites
radeon_pll_errata_after_index_slow: 31 bytes, 11 callsites
radeon_pll_errata_after_data_slow: 91 bytes, 9 callsites
radeon_pll_errata_after_FOO functions are split into two parts:
the inlined part which checks corresponding rinfo->errata bit,
and out-of-line part which performs workaround magic per se.
Reduction in code size is about 49,500 bytes:
text data bss dec hex filename
85789648 22294616 20627456 128711720 7abfc28 vmlinux.before
85740176 22294680 20627456 128662312 7ab3b28 vmlinux
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: David Airlie <airlied@linux.ie>
Cc: Alex Deucher <alexdeucher@gmail.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Dave Airlie <airlied@redhat.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-fbdev@vger.kernel.org
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The driver implements pan_display but the corresponding flags are not set.
Add FBINFO_HWACCEL_XPAN and FBINFO_HWACCEL_YPAN to flags to allow HW
accelerated panning (for fast scrolling).
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add arch_phys_wc_* calls to allow write-combining using MTRR.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The color order in truecolor modes is wrong. This does not affect console but
is visible e.g. in X11 which has wrong colors.
Swap blue and red colors to fix the problem.
Fixes https://forums.gentoo.org/viewtopic-t-692740-start-0.html
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
These chips can be present at least on x86 too - Fire GL2 AGP has GXT6000P but
this driver is currently limited to PPC.
Enable it for all architectures and add chip configuration for little-endian.
Tested on x86 with Fire GL2 AGP.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
If of_parse_display_timing() fails we are printing an error message and
jumping to the error path but we missed freeing "dt".
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The driver has a I2C device id table that is used to create the modaliases
and also "adp8870-backlight" is not a supported I2C id, so it's never used.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The driver has a I2C device id table that is used to create the modaliases
and also "adp8860-backlight" is not a supported I2C id, so it's never used.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The driver occasionally got stuck in suspend mode or other strange
states as those parts of the props struct were never initialized.
Signed-off-by: Werner Johansson <werner.johansson@sonymobile.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Acked-by: Milo Kim <milo.kim@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add DDC support for Trident cards.
Tested on TGUI9440, TGUI9680, 3DImage 9750, Blade3D 9880 and Blade XP.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
i2c-algo-bit allows I2C adapters without SCL read capability to work
but fb_ddc_read fails to work on them.
Fix fb_ddc_read to work with I2C adapters not capable of reading SCL.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We have requested the firmware and it was loaded but we missed releasing
it both on success and error.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Drivers needs to export the OF id table and this be built into
the module or udev won't have the necessary information to autoload
the driver module when the device is registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
