Cache block invalidation is removing an entry from the cache without
writing it back. Cache blocks can be invalidated via the
'invalidate_cblocks' message, which takes an arbitrary number of cblock
ranges:
invalidate_cblocks [<cblock>|<cblock begin>-<cblock end>]*
E.g.
dmsetup message my_cache 0 invalidate_cblocks 2345 3456-4567 5678-6789
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Implement policy_remove_cblock() and add remove_cblock method to the mq
policy. These methods will be used by the following cache block
invalidation patch which adds the 'invalidate_cblocks' message to the
cache core.
Also, update some comments in dm-cache-policy.h
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Rather than storing the cblock in each cache entry, we allocate all
entries in an array and infer the cblock from the entry position.
Saves 4 bytes of memory per cache block. In addition, this gives us an
easy way of looking up cache entries by cblock.
We no longer need to keep an explicit bitset to track which cblocks
have been allocated. And no searching is needed to find free cblocks.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Need to check the version to verify on-disk metadata is supported.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
"Passthrough" is a dm-cache operating mode (like writethrough or
writeback) which is intended to be used when the cache contents are not
known to be coherent with the origin device. It behaves as follows:
* All reads are served from the origin device (all reads miss the cache)
* All writes are forwarded to the origin device; additionally, write
hits cause cache block invalidates
This mode decouples cache coherency checks from cache device creation,
largely to avoid having to perform coherency checks while booting. Boot
scripts can create cache devices in passthrough mode and put them into
service (mount cached filesystems, for example) without having to worry
about coherency. Coherency that exists is maintained, although the
cache will gradually cool as writes take place.
Later, applications can perform coherency checks, the nature of which
will depend on the type of the underlying storage. If coherency can be
verified, the cache device can be transitioned to writethrough or
writeback mode while still warm; otherwise, the cache contents can be
discarded prior to transitioning to the desired operating mode.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Morgan Mears <Morgan.Mears@netapp.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Allow a cache to shrink if the blocks being removed from the cache are
not dirty.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
If a write block triggers promotion and covers a whole block we can
avoid a copy.
Introduce dm_{hook,unhook}_bio to simplify saving and restoring bio
fields (bi_private is now used by overwrite). Switch writethrough
support over to using these helpers too.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Previously these promotions only got priority if there were unused cache
blocks. Now we give them priority if there are any clean blocks in the
cache.
The fio_soak_test in the device-mapper-test-suite now gives uniform
performance across subvolumes (~16 seconds).
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
There are now two multiqueues for in cache blocks. A clean one and a
dirty one.
writeback_work comes from the dirty one. Demotions come from the clean
one.
There are two benefits:
- Performance improvement, since demoting a clean block is a noop.
- The cache cleans itself when io load is light.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Check commit_requested flag _before_ calling
dm_cache_changed_this_transaction() superfluously.
Also, be sure to set last_commit_jiffies _after_ dm_cache_commit()
completes.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Don't waste time spotting blocks that have been allocated and then freed
in the same transaction.
The extra lookup is expensive, and I don't think it really gives us much.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
The option DM_LOG_USERSPACE is sub-option of DM_MIRROR, so place it
right after DM_MIRROR. Doing so fixes various other Device mapper
targets/features to be properly nested under "Device mapper support".
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
This patch allows the removal of an open device to be deferred until
it is closed. (Previously such a removal attempt would fail.)
The deferred remove functionality is enabled by setting the flag
DM_DEFERRED_REMOVE in the ioctl structure on DM_DEV_REMOVE or
DM_REMOVE_ALL ioctl.
On return from DM_DEV_REMOVE, the flag DM_DEFERRED_REMOVE indicates if
the device was removed immediately or flagged to be removed on close -
if the flag is clear, the device was removed.
On return from DM_DEV_STATUS and other ioctls, the flag
DM_DEFERRED_REMOVE is set if the device is scheduled to be removed on
closure.
A device that is scheduled to be deleted can be revived using the
message "@cancel_deferred_remove". This message clears the
DMF_DEFERRED_REMOVE flag so that the device won't be deleted on close.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
If preresume fails it is worth logging an error given that a device is
left suspended due to the failure.
This change was motivated by local preresume error logging that was
added to the cache target ("preresume failed"). Elevating this
target-agnostic context for the where the target-specific error occurred
relative to the DM core's callouts makes sense.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Joe Thornber <ejt@redhat.com>
dm-crypt can already activate TCRYPT (TrueCrypt compatible) containers
in LRW or XTS block encryption mode.
TCRYPT containers prior to version 4.1 use CBC mode with some additional
tweaks, this patch adds support for these containers.
This new mode is implemented using special IV generator named TCW
(TrueCrypt IV with whitening). TCW IV only supports containers that are
encrypted with one cipher (Tested with AES, Twofish, Serpent, CAST5 and
TripleDES).
While this mode is legacy and is known to be vulnerable to some
watermarking attacks (e.g. revealing of hidden disk existence) it can
still be useful to activate old containers without using 3rd party
software or for independent forensic analysis of such containers.
(Both the userspace and kernel code is an independent implementation
based on the format documentation and it completely avoids use of
original source code.)
The TCW IV generator uses two additional keys: Kw (whitening seed, size
is always 16 bytes - TCW_WHITENING_SIZE) and Kiv (IV seed, size is
always the IV size of the selected cipher). These keys are concatenated
at the end of the main encryption key provided in mapping table.
While whitening is completely independent from IV, it is implemented
inside IV generator for simplification.
The whitening value is always 16 bytes long and is calculated per sector
from provided Kw as initial seed, xored with sector number and mixed
with CRC32 algorithm. Resulting value is xored with ciphertext sector
content.
IV is calculated from the provided Kiv as initial IV seed and xored with
sector number.
Detailed calculation can be found in the Truecrypt documentation for
version < 4.1 and will also be described on dm-crypt site, see:
http://code.google.com/p/cryptsetup/wiki/DMCrypt
The experimental support for activation of these containers is already
present in git devel brach of cryptsetup.
Signed-off-by: Milan Broz <gmazyland@gmail.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Some encryption modes use extra keys (e.g. loopAES has IV seed) which
are not used in block cipher initialization but are part of key string
in table constructor.
This patch adds an additional field which describes the length of the
extra key(s) and substracts it before real key encryption setting.
The key_size always includes the size, in bytes, of the key provided
in mapping table.
The key_parts describes how many parts (usually keys) are contained in
the whole key buffer. And key_extra_size contains size in bytes of
additional keys part (this number of bytes must be subtracted because it
is processed by the IV generator).
| K1 | K2 | .... | K64 | Kiv |
|----------- key_size ----------------- |
| |-key_extra_size-|
| [64 keys] | [1 key] | => key_parts = 65
Example where key string contains main key K, whitening key
Kw and IV seed Kiv:
| K | Kiv | Kw |
|--------------- key_size --------------|
| |-----key_extra_size------|
| [1 key] | [1 key] | [1 key] | => key_parts = 3
Because key_extra_size is calculated during IV mode setting, key
initialization is moved after this step.
For now, this change has no effect to supported modes (thanks to ilog2
rounding) but it is required by the following patch.
Also, fix a sparse warning in crypt_iv_lmk_one().
Signed-off-by: Milan Broz <gmazyland@gmail.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
A migration failure should be logged (albeit limited).
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Fix a few cell_defer() calls that weren't passing a bool.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Return -EINVAL when the specified cache policy is unknown rather than
returning -ENOMEM.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Rename takeout_queue to concat_queue.
Fix a harmless bug in mq policies pop() function. Currently pop()
always succeeds, with up coming changes this wont be the case.
Fix typo in comment above pre_cache_to_cache prototype.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Make the quiescing flag an atomic_t and stop protecting it with a spin
lock.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
The code that was trying to do this was inadequate. The postsuspend
method (in ioctl context), needs to wait for the worker thread to
acknowledge the request to quiesce. Otherwise the migration count may
drop to zero temporarily before the worker thread realises we're
quiescing. In this case the target will be taken down, but the worker
thread may have issued a new migration, which will cause an oops when
it completes.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org # 3.9+
Previously only origin bios could trigger ticks, which meant if all
the io was destined for the cache no ticks were generated. If no ticks
are generated then multiple hits, and movements in general, are
attributed to the same tick.
Only a stop gap fix, we need a better solution.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
It is safe to use a mutex in mq_residency() at this point since it is
only called from ioctl context. But future-proof mq_residency() by
using might_sleep() to catch new contexts that cannot sleep.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Entries would be lost if the old tail block was partially filled.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org # 3.9+
When pg_init is running no I/O can be submitted to the underlying
devices, as the path priority etc might change. When using queue_io for
this, requests will be piling up within multipath as the block I/O
scheduler just sees a _very fast_ device. All of this queued I/O has to
be resubmitted from within multipathing once pg_init is done.
This approach has the problem that it's virtually impossible to
abort I/O when pg_init is running, and we're adding heavy load
to the devices after pg_init since all of the queued I/O needs to be
resubmitted _before_ any requests can be pulled off of the request queue
and normal operation continues.
This patch will requeue the I/O that triggers the pg_init call, and
return 'busy' when pg_init is in progress. With these changes the block
I/O scheduler will stop submitting I/O during pg_init, resulting in a
quicker path switch and less I/O pressure (and memory consumption) after
pg_init.
Signed-off-by: Hannes Reinecke <hare@suse.de>
[patch header edited for clarity and typos by Mike Snitzer]
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Whenever multipath_dtr() is happening we must prevent queueing any
further path activation work. Implement this by adding a new
'pg_init_disabled' flag to the multipath structure that denotes future
path activation work should be skipped if it is set. By disabling
pg_init and then re-enabling in flush_multipath_work() we also avoid the
potential for pg_init to be initiated while suspending an mpath device.
Without this patch a race condition exists that may result in a kernel
panic:
1) If after pg_init_done() decrements pg_init_in_progress to 0, a call
to wait_for_pg_init_completion() assumes there are no more pending path
management commands.
2) If pg_init_required is set by pg_init_done(), due to retryable
mode_select errors, then process_queued_ios() will again queue the
path activation work.
3) If free_multipath() completes before activate_path() work is called a
NULL pointer dereference like the following can be seen when
accessing members of the recently destructed multipath:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000090
RIP: 0010:[<ffffffffa003db1b>] [<ffffffffa003db1b>] activate_path+0x1b/0x30 [dm_multipath]
[<ffffffff81090ac0>] worker_thread+0x170/0x2a0
[<ffffffff81096c80>] ? autoremove_wake_function+0x0/0x40
[switch to disabling pg_init in flush_multipath_work & header edits by Mike Snitzer]
Signed-off-by: Shiva Krishna Merla <shivakrishna.merla@netapp.com>
Reviewed-by: Krishnasamy Somasundaram <somasundaram.krishnasamy@netapp.com>
Tested-by: Speagle Andy <Andy.Speagle@netapp.com>
Acked-by: Junichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
dm-mpath and dm-thin must process messages even if some device is
suspended, so we allocate argv buffer with GFP_NOIO. These messages have
a small fixed number of arguments.
On the other hand, dm-switch needs to process bulk data using messages
so excessive use of GFP_NOIO could cause trouble.
The patch also lowers the default number of arguments from 64 to 8, so
that there is smaller load on GFP_NOIO allocations.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Acked-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Commit c0f04d88e4 ("bcache: Fix flushes in writeback mode") was fixing
a reported data corruption bug, but it seems some last minute
refactoring or rebasing introduced a null pointer deref.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v3.10
Reported-by: Gabriel de Perthuis <g2p.code@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A few fixes for dm-snapshot, a 32 bit fix for dm-stats, a couple error
handling fixes for dm-multipath. A fix for the thin provisioning target
to not expose non-zero discard limits if discards are disabled.
Lastly, add two DM module parameters which allow users to tune the
emergency memory reserves that DM mainatins per device -- this helps fix
a long-standing issue for dm-multipath. The conservative default
reserve for request-based dm-multipath devices (256) has proven
problematic for users with many multipathed SCSI devices but relatively
little memory. To responsibly select a smaller value users should use
the new nr_bios tracepoint info (via commit 75afb352 "block: Add nr_bios
to block_rq_remap tracepoint") to determine the peak number of bios
their workloads create.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQEcBAABAgAGBQJSQMVHAAoJEMUj8QotnQNaOXgIAJS6/XJKMoHfiDJ9M+XD34rZ
Uyr9TEnubX3DKCRBiY23MUcCQn3fx6BjCGv5/c8L4jQFIuLyDi2yatqpwXcbGSJh
G/S/y6u0Axek+ew7TS80OFop4nblW6MoKnoh9/4N55Ofa+1WvKM4ERUGjHGbauyS
TxmLQPToCFPLYRIOZ+imd6hQuIZ1+FFdJFvi7kY9O6Llx2sLD6fWi1iruBd/Da2H
ByMX3biGN45mSpcBzRbSC/FkJ9CRIvT9n82BDPS0o3Tllt8NaVlEDaovB7h4ncc0
bFuT2Z3Q38B9uZ8Lj0bqdGzv3kXMLCkLo6WhWjyUt84hmDPAzRpBwt60jUqWyZs=
=bjVp
-----END PGP SIGNATURE-----
Merge tag 'dm-3.12-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device-mapper fixes from Mike Snitzer:
"A few fixes for dm-snapshot, a 32 bit fix for dm-stats, a couple error
handling fixes for dm-multipath. A fix for the thin provisioning
target to not expose non-zero discard limits if discards are disabled.
Lastly, add two DM module parameters which allow users to tune the
emergency memory reserves that DM mainatins per device -- this helps
fix a long-standing issue for dm-multipath. The conservative default
reserve for request-based dm-multipath devices (256) has proven
problematic for users with many multipathed SCSI devices but
relatively little memory. To responsibly select a smaller value users
should use the new nr_bios tracepoint info (via commit 75afb352
"block: Add nr_bios to block_rq_remap tracepoint") to determine the
peak number of bios their workloads create"
* tag 'dm-3.12-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm: add reserved_bio_based_ios module parameter
dm: add reserved_rq_based_ios module parameter
dm: lower bio-based mempool reservation
dm thin: do not expose non-zero discard limits if discards disabled
dm mpath: disable WRITE SAME if it fails
dm-snapshot: fix performance degradation due to small hash size
dm snapshot: workaround for a false positive lockdep warning
dm stats: fix possible counter corruption on 32-bit systems
dm mpath: do not fail path on -ENOSPC
In writeback mode, when we get a cache flush we need to make sure we
issue a flush to the backing device.
The code for sending down an extra flush was wrong - by cloning the bio
we were probably getting flags that didn't make sense for a bare flush,
and also the old code was firing for FUA bios, for which we don't need
to send a flush to the backing device.
This was causing data corruption somehow - the mechanism was never
determined, but this patch fixes it for the users that were seeing it.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v3.10
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
btree_sort_fixup() was overly clever, because it was trying to avoid
pulling a key off the btree iterator in more than one place.
This led to a really obscure bug where we'd break early from the loop in
btree_sort_fixup() if the current key overlapped with keys in more than
one older set, and the next key it overlapped with was zero size.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v3.10
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
GFP_NOIO means we could be getting called recursively - mca_alloc() ->
mca_data_alloc() - definitely can't use mutex_lock(bucket_lock) then.
Whoops.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v3.10
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
bch_journal_meta() was missing the flush to make the journal write
actually go down (instead of waiting up to journal_delay_ms)...
Whoops
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v3.10
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Background writeback works by scanning the btree for dirty data and
adding those keys into a fixed size buffer, then for each dirty key in
the keybuf writing it to the backing device.
When read_dirty() finishes and it's time to scan for more dirty data, we
need to wait for the outstanding writeback IO to finish - they still
take up slots in the keybuf (so that foreground writes can check for
them to avoid races) - without that wait, we'll continually rescan when
we'll be able to add at most a key or two to the keybuf, and that takes
locks that starves foreground IO. Doh.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v3.10
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix
drivers/md/bcache/btree.c: In function ‘bch_btree_node_read’:
drivers/md/bcache/btree.c:259: warning: format ‘%lu’ expects type ‘long unsigned int’, but argument 3 has type ‘size_t’
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The journal replay code didn't handle this case, causing it to go into
an infinite loop...
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v3.10
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
sysfs attributes with unusual characters have crappy failure modes
in Squeeze (udev 164); later versions of udev are unaffected.
This should make these characters more unusual.
Signed-off-by: Gabriel de Perthuis <g2p.code@gmail.com>
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v3.10
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
That switch statement was obviously wrong, leading to some sort of weird
spinning on rare occasion with discards enabled...
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v3.10
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Allow user to change the number of IOs that are reserved by
bio-based DM's mempools by writing to this file:
/sys/module/dm_mod/parameters/reserved_bio_based_ios
The default value is RESERVED_BIO_BASED_IOS (16). The maximum allowed
value is RESERVED_MAX_IOS (1024).
Export dm_get_reserved_bio_based_ios() for use by DM targets and core
code. Switch to sizing dm-io's mempool and bioset using DM core's
configurable 'reserved_bio_based_ios'.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Frank Mayhar <fmayhar@google.com>
Allow user to change the number of IOs that are reserved by
request-based DM's mempools by writing to this file:
/sys/module/dm_mod/parameters/reserved_rq_based_ios
The default value is RESERVED_REQUEST_BASED_IOS (256). The maximum
allowed value is RESERVED_MAX_IOS (1024).
Export dm_get_reserved_rq_based_ios() for use by DM targets and core
code. Switch to sizing dm-mpath's mempool using DM core's configurable
'reserved_rq_based_ios'.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Frank Mayhar <fmayhar@google.com>
Acked-by: Mikulas Patocka <mpatocka@redhat.com>
Bio-based device mapper processing doesn't need larger mempools (like
request-based DM does), so lower the number of reserved entries for
bio-based operation. 16 was already used for bio-based DM's bioset
but mistakenly wasn't used for it's _io_cache.
Formalize difference between bio-based and request-based defaults by
introducing RESERVED_BIO_BASED_IOS and RESERVED_REQUEST_BASED_IOS.
(based on older code from Mikulas Patocka)
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Frank Mayhar <fmayhar@google.com>
Acked-by: Mikulas Patocka <mpatocka@redhat.com>
Fix issue where the block layer would stack the discard limits of the
pool's data device even if the "ignore_discard" pool feature was
specified.
The pool and thin device(s) still had discards disabled because the
QUEUE_FLAG_DISCARD request_queue flag wasn't set. But to avoid user
confusion when "ignore_discard" is used: both the pool device and the
thin device(s) have zeroes for all discard limits.
Also, always set discard_zeroes_data_unsupported in targets because they
should never advertise the 'discard_zeroes_data' capability (even if the
pool's data device supports it).
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Joe Thornber <ejt@redhat.com>
Workaround the SCSI layer's problematic WRITE SAME heuristics by
disabling WRITE SAME in the DM multipath device's queue_limits if an
underlying device disabled it.
The WRITE SAME heuristics, with both the original commit 5db44863b6
("[SCSI] sd: Implement support for WRITE SAME") and the updated commit
66c28f971 ("[SCSI] sd: Update WRITE SAME heuristics"), default to enabling
WRITE SAME(10) even without successfully determining it is supported.
After the first failed WRITE SAME the SCSI layer will disable WRITE SAME
for the device (by setting sdkp->device->no_write_same which results in
'max_write_same_sectors' in device's queue_limits to be set to 0).
When a device is stacked ontop of such a SCSI device any changes to that
SCSI device's queue_limits do not automatically propagate up the stack.
As such, a DM multipath device will not have its WRITE SAME support
disabled. This causes the block layer to continue to issue WRITE SAME
requests to the mpath device which causes paths to fail and (if mpath IO
isn't configured to queue when no paths are available) it will result in
actual IO errors to the upper layers.
This fix doesn't help configurations that have additional devices
stacked ontop of the mpath device (e.g. LVM created linear DM devices
ontop). A proper fix that restacks all the queue_limits from the bottom
of the device stack up will need to be explored if SCSI will continue to
use this model of optimistically allowing op codes and then disabling
them after they fail for the first time.
Before this patch:
EXT4-fs (dm-6): mounted filesystem with ordered data mode. Opts: (null)
device-mapper: multipath: XXX snitm debugging: got -EREMOTEIO (-121)
device-mapper: multipath: XXX snitm debugging: failing WRITE SAME IO with error=-121
end_request: critical target error, dev dm-6, sector 528
dm-6: WRITE SAME failed. Manually zeroing.
device-mapper: multipath: Failing path 8:112.
end_request: I/O error, dev dm-6, sector 4616
dm-6: WRITE SAME failed. Manually zeroing.
end_request: I/O error, dev dm-6, sector 4616
end_request: I/O error, dev dm-6, sector 5640
end_request: I/O error, dev dm-6, sector 6664
end_request: I/O error, dev dm-6, sector 7688
end_request: I/O error, dev dm-6, sector 524288
Buffer I/O error on device dm-6, logical block 65536
lost page write due to I/O error on dm-6
JBD2: Error -5 detected when updating journal superblock for dm-6-8.
end_request: I/O error, dev dm-6, sector 524296
Aborting journal on device dm-6-8.
end_request: I/O error, dev dm-6, sector 524288
Buffer I/O error on device dm-6, logical block 65536
lost page write due to I/O error on dm-6
JBD2: Error -5 detected when updating journal superblock for dm-6-8.
# cat /sys/block/sdh/queue/write_same_max_bytes
0
# cat /sys/block/dm-6/queue/write_same_max_bytes
33553920
After this patch:
EXT4-fs (dm-6): mounted filesystem with ordered data mode. Opts: (null)
device-mapper: multipath: XXX snitm debugging: got -EREMOTEIO (-121)
device-mapper: multipath: XXX snitm debugging: WRITE SAME I/O failed with error=-121
end_request: critical target error, dev dm-6, sector 528
dm-6: WRITE SAME failed. Manually zeroing.
# cat /sys/block/sdh/queue/write_same_max_bytes
0
# cat /sys/block/dm-6/queue/write_same_max_bytes
0
It should be noted that WRITE SAME support wasn't enabled in DM
multipath until v3.10.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: stable@vger.kernel.org # 3.10+
LVM2, since version 2.02.96, creates origin with zero size, then loads
the snapshot driver and then loads the origin. Consequently, the
snapshot driver sees the origin size zero and sets the hash size to the
lower bound 64. Such small hash table causes performance degradation.
This patch changes it so that the hash size is determined by the size of
snapshot volume, not minimum of origin and snapshot size. It doesn't
make sense to set the snapshot size significantly larger than the origin
size, so we do not need to take origin size into account when
calculating the hash size.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
The kernel reports a lockdep warning if a snapshot is invalidated because
it runs out of space.
The lockdep warning was triggered by commit 0976dfc1d0
("workqueue: Catch more locking problems with flush_work()") in v3.5.
The warning is false positive. The real cause for the warning is that
the lockdep engine treats different instances of md->lock as a single
lock.
This patch is a workaround - we use flush_workqueue instead of flush_work.
This code path is not performance sensitive (it is called only on
initialization or invalidation), thus it doesn't matter that we flush the
whole workqueue.
The real fix for the problem would be to teach the lockdep engine to treat
different instances of md->lock as separate locks.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Acked-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org # 3.5+
There was a deliberate race condition in dm_stat_for_entry() to avoid the
overhead of disabling and enabling interrupts. The race could result in
some events not being counted on 64-bit architectures.
However, on 32-bit architectures, operations on long long variables are
not atomic, so the race condition could cause the counter to jump by 2^32.
Such jumps could be disruptive, so we need to do proper locking on 32-bit
architectures.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: Alasdair G. Kergon <agk@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
