Looks like I missed the ranges for am335x epwmss. Let's set it up the
same way as for am437x and dra7.
Fixes: 87fc89ced3 ("ARM: dts: am335x: Move l4 child devices to probe
them with ti-sysc")
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Convert AM33xx to use the new clockdomain based layout. Previously the
clkctrl split was based on CM instance boundaries. The new layout
helps with introducing the interconnect driver instances.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The phy_id property is deprecated and phy-handle has to be used instead.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The wl1835mod.pdf data sheet says this pretty clearly for WL_IRQ line:
"WLAN SDIO out-of-band interrupt line. Set to rising edge (active high)
by default."
And it seems this interrupt can be optionally configured to use falling
edge too since commit bd763482c8 ("wl18xx: wlan_irq: support platform
dependent interrupt types").
On omap4, if the wlcore interrupt is configured as level instead of edge,
L4PER will stop doing hardware based idling after ifconfig wlan0 down is
done and the WL_EN line is pulled down.
The symptoms show up with L4PER status registers no longer showing the
IDLEST bits as 2 but as 0 for all the active GPIO banks and for
L4PER_CLKCTRL. Also the l4per_pwrdm RET count stops increasing in
the /sys/kernel/debug/pm_debug/count.
While there is also probably a GPIO related issue that needs to be
still fixed, this change gets us to the point where we can have L4PER
idling.
I'm guessing wlcore was at some point configured to use level interrupts
because of edge handling issues in gpio-omap. However, with the recent
fixes to gpio-omap the edge interrupts seem to be working just fine.
Let's change it for all omap boards with wlcore interrupt set as level.
Cc: Dave Gerlach <d-gerlach@ti.com>
Cc: Eyal Reizer <eyalr@ti.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Nishanth Menon <nm@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
[tony@atomide.com updated comments a bit for gpio issue]
Signed-off-by: Tony Lindgren <tony@atomide.com>
With the backlight phandle the driver can manage the backlight on/off in
sync with the panel enable/disable.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
am335x-evm, am335x-evmsk and am335x-beaglebone are currently relying on
pinmux set by the bootloader to set the correct value for mmc1. Fix
this by adding pinmux data for the same in kernel.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add clkctrl nodes for AM33xx SoC. These are going to be acting as
replacement for part of the existing clock data and the existing
clkctrl hooks under hwmod data.
This patch also removes any obsolete clock nodes, and reroutes all users
for these to use the new clkctrl clocks instead.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
mmc2 used for wl12xx was missing the keep-power-in suspend
parameter. As a result the board couldn't reach suspend state.
Signed-off-by: Eyal Reizer <eyalr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add stdout-path property in /chosen node so that earlycon can be
used by just adding earlycon in bootargs.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
rtc can either be supplied from internal 32k clock or external crystal
generated 32k clock. Internal clock is SoC specific and the external
clock is board dependent. Assigning the corresponding clocks.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add blue-and-red-wiring -property to lcdc node. The am335x-evmsk has
blue and red wires crossed to get 24-bit RGB (and 16-bit BGR)
support. After this patch am335x-evmsk supports BGR565, RGB888, and
XRGB8888 color formats. See details in
Documentation/devicetree/bindings/display/tilcdc/tilcdc.txt.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Whitespace cleanup of lcdc related nodes. Do all indentation and
alignment with tabs instead of spaces.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings:
"Node /memory has a reg or ranges property, but no unit name"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings for many boards:
"Node /leds/led@1 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings for many boards:
"Node /gpio_keys/button0@10 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings for many boards:
"Node /fixedregulator@0 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Now that we are moving to OPPv2 bindings and able to add 1GHz OPP for
MPU, let's update the max MPU voltage range to align with the maximum
possible value allowed in the operating-points table, which is max
target voltage of 132500 uV + 2%.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Though the keyboard driver for GPIO buttons(gpio-keys) will continue to
check for/support the legacy "gpio-key,wakeup" boolean property to
enable gpio buttons as wakeup source, "wakeup-source" is the new
standard binding.
This patch replaces the legacy "gpio-key,wakeup" with the unified
"wakeup-source" property in order to avoid any futher copy-paste
duplication.
Cc: "Benoît Cousson" <bcousson@baylibre.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use the pinmux IOPAD macro to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.
Also, use the mux defines instead of magic numbers for the padconf
values when defining the pinctrl lines to make it more readable.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
As per mmc device tree binding documentation card detect gpio has
to be active low signal. When a hardware is designed with active
high card detect, gpio polarity has to be changed with
cd-inverted dt property.
In AM335x the card detect gpio is designed as active low gpio.
So correcting the dt card detect gpio definition.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The sound support consist only Headset output on the board and can be
handled by "simple-audio-card"
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
When McASP is not in use the pins can be put to sleep mode to conserve
power.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
While Sitara AM335x SoCs are very close to OMAP SoCs, the 32-line GPIO
controllers are numbered from 0 on AM335x and from 1 on OMAP. But when
the configuration for the TI WLAN controllers was converted from
platform data to device tree, this detail was overlooked, as 10 boards
were using OMAP with the WL12xx and WL18xx controllers, and only one
was based on AM335x.
This invalid configuration prevents the WL1271 module on the AM335x
EVM-SK from notifying interrupts to the SoC, and breaks the wlan driver.
The DTS must be corrected to use the correct GPIO controller.
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Replace all the pdata-quirks for setting wl12xx/wl18xx
platform data with proper DT definitions.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Acked-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Tested-by: Nikita Kiryanov <nikita@compulab.co.il>
Tested-by: Tony Lindgren <tony@atomide.com>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
- Document and use new cadence serial binding
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)
iEYEABECAAYFAlPI73sACgkQykllyylKDCGYzQCggc3g80f6R008+SNKlrN0Wuy+
b9kAnjqTO0Q0kDf4PlI/a5EVsfPmOzoS
=Bo6W
-----END PGP SIGNATURE-----
Merge tag 'zynq-dt-for-3.17' of git://git.xilinx.com/linux-xlnx into next/dt
Merge "Xilinx Zynq changes for v3.17" from Michal Simek:
arm: Xilinx Zynq dt patches for v3.17
- Document and use new cadence serial binding
* tag 'zynq-dt-for-3.17' of git://git.xilinx.com/linux-xlnx:
ARM: zynq: DT: Migrate UART to Cadence binding
tty: cadence: Document DT binding
+ Linux 3.16-rc5
Signed-off-by: Olof Johansson <olof@lixom.net>
The use of FIFO in McASP can reduce the risk of audio under/overrun and
lowers the load on the memories since the DMA will operate in bursts.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add the necessary nodes to enable the LCD controller and the
LCD panel that is attached to the Texas Instruments AM335x
EVMSK platform. Also setup the necessary pin mux within the
DT file to drive the LCD connector and add the correct
pinmux settings for the lcd pins to be configured to when
the SoC goes into sleep state for the minimum power
consumption.
For the sleep mode LCD pin settings, MUX_MODE7 is chosen as
this corresponds to switching the pins into input GPIO's with
an internal pulldown. Which has been determined to offer the
lowest power solution vs leaving the pins configured in LCD
mode.
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Acked-by: Wolfram Sang <wsa@sang-engineering.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Make sure ethernet and mdio nodes are disabled by default and enable
them explicitly only on boards that actually use them.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The VTT regulator for DDR3 termination on the am335x-evmsk is
controlled by a gpio. It is configured by the bootloader so here we
define an always-on, fixed voltage regulator to hold the gpio.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use phandles instead of unit adresses to reference usb and dma nodes.
This makes the DT more robust and readable.
Signed-off-by: Guido Martínez <guido@vanguardiasur.com.ar>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In "ARM: dts: am33xx: correcting dt node unit address for usb", the
usb_ctrl_mod and cppi41dma nodes were updated with the correct register
addresses. However, the dts files that reference these nodes were not
updated, and those devices are no longer being enabled.
This patch corrects the references for the affected dts files.
Signed-off-by: Leigh Brown <leigh@solinno.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
These are sent separately from the rest of the .dts changes
as these depend on the fixes merged into v3.14-rc4, and
needed a bit more time to get updated on the fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=rAdr
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.15/dt-overo-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Updates to the .dts files to support more Gumstix boards.
These are sent separately from the rest of the .dts changes
as these depend on the fixes merged into v3.14-rc4, and
needed a bit more time to get updated on the fixes.
* tag 'omap-for-v3.15/dt-overo-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Add support for the Overo Summit
ARM: dts: Add support for the Overo Chestnut43
ARM: dts: Add support for the Overo Alto35
ARM: dts: Add support for the Overo Gallop43
ARM: dts: Add support for the Overo Palo43
ARM: dts: overo: Add LIS33DE accelerometer
ARM: dts: overo: Create a file for common Gumstix peripherals
ARM: dts: overo: Push uart3 pinmux down to expansion board
ARM: dts: omap3-tobi: Add AT24C01 EEPROM
ARM: dts: omap3-tobi: Use include file omap-gpmc-smsc9221
ARM: dts: omap: Add common file for SMSC9221
ARM: dts: omap3-overo: Add HSUSB PHY
ARM: dts: omap3-overo: Enable WiFi/BT combo
ARM: dts: omap3-overo: Add missing pinctrl
ARM: dts: omap3-tobi: Add missing pinctrl
ARM: dts: overo: reorganize include files
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Conflicts:
arch/arm/boot/dts/omap3-overo.dtsi
EVM board provides two Ethernet ports, this patch sets them into
dual_emac mode to provide two independent network interfaces.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enable second USB channel and set it into 'host' mode.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The clock for audio is sourced from virt_24000000_ck, so the correct
frequency is 24000000.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
CC: <stable@vger.kernel.org> # 3.13.x
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add pinctrl section and cd-gpio to mmc1. Without these the SD card is not
working on EVM-SK board.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The clock for audio is sourced from virt_24000000_ck, so the correct
frequency is 24000000.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Pull input updates from Dmitry Torokhov:
"Updates for the input subsystem. You will get an new drivers for
Hyper-V synthetic keyboard and for Neonode zForce touchscreens, plus a
bunch of driver fixes and cleanups"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (49 commits)
Revert "Input: ALPS - add support for model found on Dell XT2"
arm: dts: am335x sk: add touchscreen support
Input: ti_am335x_tsc - fix spelling mistake in TSC/ADC DT binding
Input: cyttsp4 - replace IS_ERR and PTR_ERR with PTR_ERR_OR_ZERO
Input: mma8450 - add missing i2c_set_clientdata() in mma8450_probe()
Input: mpu3050 - add missing i2c_set_clientdata() in mpu3050_probe()
Input: tnetv107x-keypad - make irqs signed for error handling
Input: add driver for Neonode zForce based touchscreens
Input: sh_keysc - enable the driver on all ARM platforms
Input: remove a redundant max() call
Input: mousedev - allow disabling even without CONFIG_EXPERT
Input: allow deselecting serio drivers even without CONFIG_EXPERT
Input: i8042 - add PNP modaliases
Input: evdev - fall back to vmalloc for client event buffer
Input: cypress_ps2 - do not consider data bad if palm is detected
Input: cypress_ps2 - remove useless cast
Input: fix PWM-related undefined reference errors
Input: ALPS - change secondary device's name
Input: wacom - not all multi-interface devices support touch
Input: nspire-keypad - add missing clk_disable_unprepare() on error path
...
Add missing nodes for the touchscreen available on AM335x EVM SK.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
AM335x EVM-SK have only support for audio playback (stereo jack on the
board) via tlv320aic3106 codec connected to McASP1.
Enable the support for audio playback on the board:
- McASP1 configuration
- tlv320aic3106 configuration
- Machine driver.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Do not reset GPIO0 at boot-up because GPIO0 is used
on AM335x EVM-SK to control VTT regulators on DDR3.
Without this EVM-SK boards fail to boot-up because
of DDR3 corruption.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Add the generic AM33XX AES module's device tree data and
enable it for the am335x-evm, am335x-evmsk, and am335x-bone
platforms. Also add Documentation file describing the data
for the AES module.
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Joel Fernandes <joelf@ti.com>
[joelf@ti.com: Dropped interrupt-parent property, documentation fixups]
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Add the generic AM33XX SHAM module's device tree data and
enable it for the am335x-evm, am335x-evmsk, and am335x-bone
platforms. Also add Documentation file describing the data
for the SHAM module.
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Joel Fernandes <joelf@ti.com>
[joelf@ti.com: Dropped interrupt-parent property, documentation fixups]
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
The On Chip Peripherals (OCP) device node is a simplified
representation of the AM33XX SoC interconnect. An OCP dev
node is already defined in the am33xx.dtsi Device Tree
source file included by am33xx based boards so there is
no need to redefine this on each board DT file.
Also, the OCP and IP modules directly connected to it are SoC
internal details that is better to keep outside of board files.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
am33xx boards DTS include the am33xx.dtsi Device Tree
source file that already define a pinmux device node for
the AM33XX SoC Pin Multiplex.
Redefining this for each board makes the Device Tree files
harder to modify and maintain so let's just use what is
already defined in the included .dtsi file.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Adds AM33XX MMC support for am335x-bone, am335x-evm and am335x-evmsk boards.
Also added is the DMA binding definitions based on the generic DMA request
binding.
Additional changes made to DTS:
* Interrupt, reg and compatible properties added
* ti,needs-special-hs-handling added
Signed-off-by: Matt Porter <mporter@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
