Intel Tiger Lake-H has different pin layout than the -LP variant
so add support for this to the existing Tiger Lake driver.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
It is useful to control I²S bus 2 pins if we would like to connect
an audio codec.
Reported-by: mouse <xllacyx@gmail.com>
Reported-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Some of the pin names were provided officially to the customers
in different spelling. We update pin names in accordance with
the official list.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The pins on the Bay Trail SoC have separate input-buffer and output-buffer
enable bits and a read of the level bit of the value register will always
return the value from the input-buffer.
The BIOS of a device may configure a pin in output-only mode, only enabling
the output buffer, and write 1 to the level bit to drive the pin high.
This 1 written to the level bit will be stored inside the data-latch of the
output buffer.
But a subsequent read of the value register will return 0 for the level bit
because the input-buffer is disabled. This causes a read-modify-write as
done by byt_gpio_set_direction() to write 0 to the level bit, driving the
pin low!
Before this commit byt_gpio_direction_output() relied on
pinctrl_gpio_direction_output() to set the direction, followed by a call
to byt_gpio_set() to apply the selected value. This causes the pin to
go low between the pinctrl_gpio_direction_output() and byt_gpio_set()
calls.
Change byt_gpio_direction_output() to directly make the register
modifications itself instead. Replacing the 2 subsequent writes to the
value register with a single write.
Note that the pinctrl code does not keep track internally of the direction,
so not going through pinctrl_gpio_direction_output() is not an issue.
This issue was noticed on a Trekstor SurfTab Twin 10.1. When the panel is
already on at boot (no external monitor connected), then the i915 driver
does a gpiod_get(..., GPIOD_OUT_HIGH) for the panel-enable GPIO. The
temporarily going low of that GPIO was causing the panel to reset itself
after which it would not show an image until it was turned off and back on
again (until a full modeset was done on it). This commit fixes this.
This commit also updates the byt_gpio_direction_input() to use direct
register accesses instead of going through pinctrl_gpio_direction_input(),
to keep it consistent with byt_gpio_direction_output().
Note for backporting, this commit depends on:
commit e2b74419e5 ("pinctrl: baytrail: Replace WARN with dev_info_once
when setting direct-irq pin to output")
Cc: stable@vger.kernel.org
Fixes: 86e3ef812f ("pinctrl: baytrail: Update gpio chip operations")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Since we dependent on ACPI, there is no need to use ACPI_PTR()
which is a no-op in this case.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Since we dependent on ACPI, there is no need to use ACPI_PTR()
which is a no-op in this case.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Introduce couple of helpers to enable or disable input. i.e.
lp_gpio_enable_input() and lp_gpio_disable_input().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Make use of for_each_requested_gpio() instead of home grown analogue.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Make use of for_each_requested_gpio_in_range() instead of home grown analogue.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Protect IO in intel_gpio_get_direction(), intel_gpio_community_irq_handler(),
intel_config_get_debounce() and intel_config_get_pull() by lock. Even for
simple readl() we better serialize IO to avoid potential problems.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Split intel_config_get() to three functions, i.e. intel_config_get() and
two helpers intel_config_get_pull() and intel_config_get_debounce() to be
symmetrical with intel_config_set*().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Drop the only label in the code, i.e. in intel_config_set_debounce(),
for consistency with the rest. In entire driver we use multipoint
return.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
In a code like
if (...) {
...
goto label;
} else {
...
}
the 'else' keyword is redundant. Get rid of it for better readability.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Instead of using bitwise operations against returned values,
which is a bit fragile, convert IRQ handler to count amount of
GPIO groups, where at least one interrupt happened, and convert
it to returned value by IRQ_RETVAL() macro.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
In some cases lock covers unneeded calls and operations.
Reduce scope of the lock in such cases.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
It's possible scenario that pin has been in different mode, while
the respective GPIO register has a leftover output buffer enabled.
In such case when we request GPIO it will switch to GPIO mode, and
thus to output with unknown value, followed by switching to input
mode. This can produce a glitch on the pin.
Disable input and output buffer when switching to GPIO to avoid
potential glitches.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
We have some data structures duplicated across the drivers.
Let's deduplicate them by using struct intel_pinctrl_soc_data,
struct intel_community and struct intel_pinctrl_context that
are being provided by pinctrl-intel.h.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Individual drivers may install ACPI OpRegion handlers based on
address space ID which differs from community to community.
Add special field in the struct intel_community for that purpose.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Some of the pin control devices may not be capable to generate IRQ
per each pin in the community. Allow individual drivers to define
total amount of IRQs per community.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
chv_writel() is now solely used for cases where we write data
to the PAD registers. In order to simplify callers, calculate
register address inside chv_writel().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Pin control device and effectively the single community in it has
a set of common registers. It's good to have a helpers to IO on them.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
There are plenty of places where we call
readl(chv_padreg(pctrl, offset, ...));
Replace them with newly introduced chv_readl() helper
chv_readl(pctrl, offset, ...);
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Make use of for_each_requested_gpio() instead of home grown analogue.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200615150545.87964-6-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
kernel cycle.
New drivers:
- Intel Jasper Lake support.
- NXP Freescale i.MX8DXL support.
- Qualcomm SM8250 support.
- Renesas R8A7742 SH-PFC support.
Driver improvements:
- Severe cleanup and modernization of the MCP23s08 driver.
- Mediatek driver modularized.
- Setting config supported in the Meson driver.
- Wakeup support for the Broadcom BCM7211.
-----BEGIN PGP SIGNATURE-----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=3UGk
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v5.8 kernel cycle.
It's just really boring this time. Zero core changes. Just linear
development, cleanups and misc noncritical fixes. Some new drivers for
very new Qualcomm and Intel chips.
New drivers:
- Intel Jasper Lake support.
- NXP Freescale i.MX8DXL support.
- Qualcomm SM8250 support.
- Renesas R8A7742 SH-PFC support.
Driver improvements:
- Severe cleanup and modernization of the MCP23s08 driver.
- Mediatek driver modularized.
- Setting config supported in the Meson driver.
- Wakeup support for the Broadcom BCM7211"
* tag 'pinctrl-v5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (72 commits)
pinctrl: sprd: Fix the incorrect pull-up definition
pinctrl: pxa: pxa2xx: Remove 'pxa2xx_pinctrl_exit()' which is unused and broken
pinctrl: freescale: imx: Use 'devm_of_iomap()' to avoid a resource leak in case of error in 'imx_pinctrl_probe()'
pinctrl: freescale: imx: Fix an error handling path in 'imx_pinctrl_probe()'
pinctrl: sirf: add missing put_device() call in sirfsoc_gpio_probe()
pinctrl: imxl: Fix an error handling path in 'imx1_pinctrl_core_probe()'
pinctrl: bcm2835: Add support for wake-up interrupts
pinctrl: bcm2835: Match BCM7211 compatible string
dt-bindings: pinctrl: Document optional BCM7211 wake-up interrupts
dt-bindings: pinctrl: Document 7211 compatible for brcm, bcm2835-gpio.txt
dt-bindings: pinctrl: stm32: Add missing interrupts property
pinctrl: at91-pio4: Add COMPILE_TEST support
pinctrl: Fix return value about devm_platform_ioremap_resource()
MAINTAINERS: Renesas Pin Controllers are supported
dt-bindings: pinctrl: ocelot: Add Sparx5 SoC support
pinctrl: ocelot: Fix GPIO interrupt decoding on Jaguar2
pinctrl: ocelot: Remove instance number from pin functions
pinctrl: ocelot: Always register GPIO driver
dt-bindings: pinctrl: rockchip: update example
pinctrl: amd: Add ACPI dependency
...
Commit 6d33ee7a05 ("pinctrl: pxa: Use devm_pinctrl_register() for pinctrl registration")
has turned a 'pinctrl_register()' into 'devm_pinctrl_register()' in
'pxa2xx_pinctrl_init()'.
However, the corresponding 'pinctrl_unregister()' call in
'pxa2xx_pinctrl_exit()' has not been removed.
This is not an issue, because 'pxa2xx_pinctrl_exit()' is unused.
Remove it now to avoid some wondering in the future and save a few LoC.
Fixes: 6d33ee7a05 ("pinctrl: pxa: Use devm_pinctrl_register() for pinctrl registration")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Link: https://lore.kernel.org/r/20200531073716.593343-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
'pinctrl_unregister()' should not be called to undo
'devm_pinctrl_register_and_init()', it is already handled by the framework.
This simplifies the error handling paths of the probe function.
The 'imx_free_resources()' can be removed as well.
Fixes: a51c158bf0 ("pinctrl: imx: use radix trees for groups and functions")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Link: https://lore.kernel.org/r/20200530204955.588962-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
A coccicheck run provided information like the following:
drivers/pinctrl/sirf/pinctrl-sirf.c:798:2-8: ERROR: missing put_device;
call of_find_device_by_node on line 792, but without a corresponding
object release within this function.
Generated by: scripts/coccinelle/free/put_device.cocci
Thus add a jump target to fix the exception handling for this
function implementation.
Fixes: 5130216265 ("PINCTRL: SiRF: add GPIO and GPIO irq support in CSR SiRFprimaII")
Signed-off-by: yu kuai <yukuai3@huawei.com>
Link: https://lore.kernel.org/r/20200603013532.755220-1-yukuai3@huawei.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When 'pinctrl_register()' has been turned into 'devm_pinctrl_register()',
an error handling path has not been updated.
Axe a now unneeded 'pinctrl_unregister()'.
Fixes: e55e025d16 ("pinctrl: imxl: Use devm_pinctrl_register() for pinctrl registration")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/20200530201952.585798-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Leverage the IRQCHIP_MASK_ON_SUSPEND flag in order to avoid having to
specifically treat the GPIO interrupts during suspend and resume, and
simply implement an irq_set_wake() callback that is responsible for
enabling the parent wake-up interrupt as a wake-up interrupt.
To avoid allocating unnecessary resources for other chips, the wake-up
interrupts are only initialized if we have a brcm,bcm7211-gpio
compatibility string.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20200531001101.24945-5-f.fainelli@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The BCM7211 SoC uses the same pinconf_ops as the ones defined for the
BCM2711 SoC, match the compatible string and use the correct set of
options.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20200531001101.24945-4-f.fainelli@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When call function devm_platform_ioremap_resource(), we should use IS_ERR()
to check the return value and return PTR_ERR() if failed.
Fixes: 4b024225c4 ("pinctrl: use devm_platform_ioremap_resource() to simplify code")
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Link: https://lore.kernel.org/r/1590234326-2194-1-git-send-email-yangtiezhu@loongson.cn
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- Add support for the new RZ/G1H (r8a7742) SoC,
- Minor fixes and improvements.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCXsU4BgAKCRCKwlD9ZEnx
cLVzAP9GTdDrxNO4d9JceM3WvhsX/JrpXOOJjgjObAZj7AtN3AEA0iXhBsIOP7lN
oiAYEWBTmaAVBvwaVWdvKT4AhLEv3wQ=
=kdu0
-----END PGP SIGNATURE-----
Merge tag 'sh-pfc-for-v5.8-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel
pinctrl: sh-pfc: Updates for v5.8 (take two)
- Add support for the new RZ/G1H (r8a7742) SoC,
- Minor fixes and improvements.
Two fixes for S5Pv210 pinctrl driver: setting proper external interrupt
wakeup mask and restoring external interrupt mask value after system
suspend.
-----BEGIN PGP SIGNATURE-----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=9T4z
-----END PGP SIGNATURE-----
Merge tag 'samsung-pinctrl-5.8' of https://git.kernel.org/pub/scm/linux/kernel/git/pinctrl/samsung into devel
Samsung pinctrl drivers changes for v5.8
Two fixes for S5Pv210 pinctrl driver: setting proper external interrupt
wakeup mask and restoring external interrupt mask value after system
suspend.
This fixes a problem with using the GPIO as an interrupt on Jaguar2
(and similar), as the register layout of the platforms with 64 GPIO's
are pairwise, such that the original offset must be multiplied with
the platform stride.
Fixes: da801ab56a pinctrl: ocelot: add MSCC Jaguar2 support.
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Link: https://lore.kernel.org/r/20200513125532.24585-4-lars.povlsen@microchip.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch removes the instance number from the "miim", "reco_clk" and
"sfp" pin function.
The change needed is to prepare the driver for adding new platforms
with more of these instances. The instance number is also redundant,
as this is implicit for each pin.
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Link: https://lore.kernel.org/r/20200513125532.24585-3-lars.povlsen@microchip.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This fixes the situation where the GPIO controller is not
used as an interrupt controller as well.
Previously, the driver would silently fail to register even the
GPIO's. With this change, the driver will only register as an
interrupt controller if a parent interrupt is provided.
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Link: https://lore.kernel.org/r/20200513125532.24585-2-lars.povlsen@microchip.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently the AMD pin controller driver supports ACPI platform only.
Make the PINCTRL_AMD config symbol depend on ACPI, to avoid asking the
user about it when configuring a kernel without ACPI support.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200507113751.24213-1-geert+renesas@glider.be
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Equilibrium pin controller is only present on Intel Lightning
Mountain SoCs. Add an architecture dependency to the
PINCTRL_EQUILIBRIUM config symbol, to avoid asking the user about it
when configuring a kernel for a non-x86 architecture.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200507113626.24026-2-geert+renesas@glider.be
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* Introduce GPIO driver for Jasper Lake
* Fix long standing bug in Sunrisepoint-H PAD locking code
* Enable pin configuration setting for GPIO chip for Baytrail
* Work around race condition in Cherriview hardware when handle IRQ
* Clean up Cherryview code to be closer to other drivers
The following is an automated git shortlog grouped by driver:
baytrail:
- Use platform_get_irq_optional() explicitly
- Enable pin configuration setting for GPIO chip
cannonlake:
- Use generic flag for special GPIO base treatment
cherryview:
- Add missing spinlock usage in chv_gpio_irq_handler
- Use GENMASK() consistently
- Re-use data structures from pinctrl-intel.h (part 2)
icelake:
- Use generic flag for special GPIO base treatment
intel:
- Move npins closer to pin_base in struct intel_community
- Update description in struct intel_community
- Add Intel Jasper Lake pin controller support
- Introduce new flag to force GPIO base to be 0
- Introduce common flags for GPIO mapping scheme
lynxpoint:
- Use platform_get_irq_optional() explicitly
sunrisepoint:
- Fix PAD lock register offset for SPT-H
tigerlake:
- Use generic flag for special GPIO base treatment
-----BEGIN PGP SIGNATURE-----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=e+Dg
-----END PGP SIGNATURE-----
Merge tag 'intel-pinctrl-v5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pinctrl/intel into devel
intel-pinctrl for v5.8-1
* Introduce GPIO driver for Jasper Lake
* Fix long standing bug in Sunrisepoint-H PAD locking code
* Enable pin configuration setting for GPIO chip for Baytrail
* Work around race condition in Cherriview hardware when handle IRQ
* Clean up Cherryview code to be closer to other drivers
The following is an automated git shortlog grouped by driver:
baytrail:
- Use platform_get_irq_optional() explicitly
- Enable pin configuration setting for GPIO chip
cannonlake:
- Use generic flag for special GPIO base treatment
cherryview:
- Add missing spinlock usage in chv_gpio_irq_handler
- Use GENMASK() consistently
- Re-use data structures from pinctrl-intel.h (part 2)
icelake:
- Use generic flag for special GPIO base treatment
intel:
- Move npins closer to pin_base in struct intel_community
- Update description in struct intel_community
- Add Intel Jasper Lake pin controller support
- Introduce new flag to force GPIO base to be 0
- Introduce common flags for GPIO mapping scheme
lynxpoint:
- Use platform_get_irq_optional() explicitly
sunrisepoint:
- Fix PAD lock register offset for SPT-H
tigerlake:
- Use generic flag for special GPIO base treatment
Renesas RZ/G1H (R8A7742) is pin compatible with R-Car H2 (R8A7790),
however it doesn't have several automotive specific peripherals. Add
automotive-specific pin groups/functions along with common pin
groups/functions for supporting both r8a7790 and r8a7742 SoC.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Marian-Cristian Rotariu <marian-cristian.rotariu.rb@bp.renesas.com>
Link: https://lore.kernel.org/r/1588542414-14826-3-git-send-email-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
In function rockchip_dt_node_to_map, a new_map variable is
allocated by:
new_map = devm_kcalloc(pctldev->dev, map_num, sizeof(*new_map),
GFP_KERNEL);
This uses devres and attaches new_map to the pinctrl driver.
This cause a leak since new_map is not released when the probed
driver is removed. Fix it by using kcalloc to allocate new_map
and free it in `rockchip_dt_free_map`
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20200506100903.15420-1-dafna.hirschfeld@collabora.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Kbuild warns when this file is built as a loadable module:
WARNING: modpost: missing MODULE_LICENSE() in drivers/pinctrl/mediatek/pinctrl-mtk-common-v2.o
see include/linux/module.h for more information
Add the missing license/author/description tags.
Fixes: 8174a8512e ("pinctrl: mediatek: make MediaTek pinctrl v2 driver ready for buidling loadable module")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20200505140848.554957-1-arnd@arndb.de
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These are called when a GPIO is to be used as IRQ.
Without these custom callbacks, when an interrupt is requested directly
and not through gpiod_to_irq(), the request fails because the GPIO is
not necesarily in input mode. These callbacks simply enforce that the
requested GPIO is in input mode.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20200503164549.163884-1-paul@crapouillou.net
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Wakeup capable GPIO IRQs routed via PDC are not being migrated when a CPU
is hotplugged. Add affinity callbacks to msmgpio IRQ chip to update the
affinity of wakeup capable IRQs.
Fixes: e35a6ae0eb ("pinctrl/msm: Setup GPIO chip in hierarchy")
Signed-off-by: Venkata Narendra Kumar Gutta <vnkgutta@codeaurora.org>
[mkshah: updated commit text and minor code fixes]
Signed-off-by: Maulik Shah <mkshah@codeaurora.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/1588314617-4556-1-git-send-email-mkshah@codeaurora.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
