QCA9984 shares the same configuration with QCA99X0.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
QCA9984 Rx descriptor has two 32-bit words of location information
when compared to one 32-bit word in QCA99X0. To handle this difference in
rx descriptor ppdu_end, define a new ppdu_end for QCA9984 descriptor
which has the new structure to represent rx_location_info.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Store pci chip secific reset funtions in struct ath10k_pci
as callbacks during early ath10k_pci_probe() and use the
callback to perform chip specific resets. This patch essentially
adds two callback in ath10k_pci, one for doing soft reset and
the other for hard reset. By using callbacks we can get rid of
those hw revision checks in ath10k_pci_safe_chip_reset() and
ath10k_pci_chip_reset(). As such this patch does not fix
any issue.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Define rx_location_info in struct rx_ppdu_end_qca99x0 after
rx_pkt_end. This is to prepare rx_ppdu_end for QCA9984 chip.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In QCA4019, cycle counter wraparound in same fashion
as QCA988X. When the cycle counter wraparound it
resets to 0x7fffffff. Set has_shifted_cc_wraparound to
true for QCA4019 to enable the code path to handle cycle
counter wraparound for consistent survey report.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In 10.4, fw sends WMI PEER_RATECODE_LIST_EVENTID after successful
peer_assoc cmd. As of now this event is not of much use and not
implemented. Change the debug level and messsage as appropriate
to suppress "Unknown eventid: 36898".
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
During hw scan, firmware sends two channel information events (pre-
complete, complete) to host for each channel change. The snap shot of cycle
counters (rx_clear and total) between these two events are given for
survey dump. In order to get latest survey statistics of all channels, a
scan request has to be issued. In general, an AP DUT is brought up, it
won't leave BSS channel except few cases like overlapping bss or radar
detection. So survey statistics of bss channel is always referring to
older data that are collected before starting AP (either ACS/OBSS scan).
To collect latest survey information from target, firmware provides WMI
interface to read cycle counters from hardware. For each survey dump
request, BSS channel cycle counters are read and cleared in hardware.
This makes sure that behavior is in align with ath9k survey report.
So survey dump always gives snap shot of cycle counters b/w two survey
requests.
Signed-off-by: Yanbo Li <yanbol@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add handler to process bss channel information wmi event that
will be received upon sending pdev_chan_info_request wmi command.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add WMI ops to send pdev_bss_chan_info_request command to target.
This command will be used to retrieve updated cycle counters and noise
floor value of current operating channel (bss channel).
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add WMI definitions for pdev bss channel information request and
event.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It is observed that while loading and unloading ath10k modules
in an infinite loop, before ath10k_core_start() completion HTT
rx frames are received, while processing these frames,
dereferencing the arvifs list code is getting hit before
initilizing the arvifs list, causing a kernel panic.
This patch initilizes the arvifs list before initilizing htt.
Fixes the below issue:
[<bf88b058>] (ath10k_htt_rx_pktlog_completion_handler+0x278/0xd08 [ath10k_core])
[<bf88b058>] (ath10k_htt_rx_pktlog_completion_handler [ath10k_core])
[<bf88c0dc>] (ath10k_htt_txrx_compl_task+0x5f4/0xeb0 [ath10k_core])
[<bf88c0dc>] (ath10k_htt_txrx_compl_task [ath10k_core])
[<c0234100>] (tasklet_action+0x8c/0xec)
[<c0234100>] (tasklet_action)
[<c02337c0>] (__do_softirq+0xf8/0x228)
[<c02337c0>] (__do_softirq) [<c0233920>] (run_ksoftirqd+0x30/0x90)
Code: e5954ad8 e2899008 e1540009 0a00000d (e5943008)
---[ end trace 71de5c2e011dbf56 ]---
Kernel panic - not syncing: Fatal exception in interrupt
Fixes: 500ff9f938 ("ath10k: implement chanctx API")
Cc: <stable@vger.kernel.org>
Signed-off-by: Anilkumar Kolli <akolli@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Spectral related structures are accessed / modified only if ath10k
debugfs is enabled, so it makes more sense to move them under
ATH10K_DEBUGFS
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
According to the spec, VHT doesn't exist in 2.4GHz.
There are vendor extensions to allow a subset of VHT to work
(notably 256-QAM), but since mac80211 doesn't support those
advertising VHT capability on 2.4GHz leads to the behaviour
of reporting VHT capabilities but not being able to use any
of them due to mac80211's code requiring 80 MHz support.
Remove the VHT capabilities from 2.4GHz for now. If mac80211
gets extended to use the (likely Broadcom) vendor IEs for it
and handles the lack of 80 MHz support, it can be added back.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
fix a typo (spelling mistake) in 'ath10k_start'
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
QCA6174 WLAN.RM.2.0 firmware uses max_tx_power instead of using max_reg_power
to set transmission power. The tx power was about -50dbm, after applying this
change, it become -32dbm.
Signed-off-by: Alan Liu <alanliu@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath.git patches for 4.7. Major changes:
ath10k
* implement set_tsf() for 10.2.4 branch
* remove rare MSI range support
* remove deprecated firmware API 1 support
ath9k
* add module parameter to invert LED polarity
wcn36xx
* fixes to get the driver properly working on Dragonboard 410c
Now that all firmware-N.bin related are within struct ath10k_fw_file we can
switch to use ath10k_core_fetch_firmware_api_n() and delete almost identical
ath10k_tm_fetch_utf_firmware_api_2().
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
To make it easier to share ath10k_core_fetch_board_data_api_n() with testmode.c
refactor all firmware components to struct ath10k_fw_components. This structure
will hold firmware related files, for example firmware-N.bin and board-N.bin.
For firmware-N.bin create a new struct ath10k_fw_file which contains the actual
firmware image as well as the parsed data from the image.
Modify ath10k_core_start() to take struct ath10k_fw_components() as an argument
which makes it possible in following patches to drop some ugly hacks from
testmode.c.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This has ben deprecated years ago, I haven't heard anyone using it since and
most likely it won't even work anymore. So just remove all of it.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
push-pull mode needs certain amount the host driver involvement for
managing queues in the host memory and packet delivery to firmware.
qca4019 wifi firmware has an option to stay in push mode for less
number of active traffic flow and then switch to push-pull mode when
the active traffic flow goes beyond the certain limit.
The advantage of staying in push mode for less active traffic is, the
host cpu consumption is reduced. qca4019 firmware supports this
flexibility of the mode switch. It takes the host driver interest
(LOW_PERF/HIGH_PERF) via WMI_EXT_RESOURCE_CFG_CMDID,
LOW_PERF - fw would stay in push mode and switch to push-pull
based on demand.
HIGH_PERF - fw would stay in push-pull mode from the boot.
To make this configuration generic, new WMI services
WMI_SERVICE_TX_MODE_PUSH_ONLY, WMI_SERVICE_TX_MODE_PUSH_PULL,
WMI_SERVICE_TX_MODE_DYNAMIC are introduced to take dynamic tx mode
switch support availability in firmware.
Based on WMI_SERVICE_TX_MODE_DYNAMIC, LOW_PERF or HIGHT_PERF is
configured to the firmware.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Smatch complains that since "ev->peer_id" comes from skb->data that
means we can't trust it and have to do a bounds check on it to prevent
an array overflow.
Fixes: 6942726f7f ('ath10k: add fast peer_map lookup')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Upon firmware assert, restart work will be triggered so that mac80211
will reconfigure the driver. An issue is reported that after restart
work, survey dump data do not contain in-use (SURVEY_INFO_IN_USE) info
for operating channel. During reconfigure, since mac80211 already has
valid channel context for given radio, channel context iteration return
num_chanctx > 0. Hence rx_channel is always NULL. Fix this by assigning
channel context to rx_channel when driver restart is in progress.
Cc: stable@vger.kernel.org
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Return value is incorrect for btcoex and peer stats debugfs
'write' entries if the user provides a value that matches with
the already available debugfs entry, this results in the debugfs
entry getting stuck and the operation has to be terminated manually.
Fix this by returning the appropriate return 'count' as we do it for
other debugfs entries like pktlog etc.
Fixes: cc61a1bbbc ("ath10k: enable debugfs provision to enable Peer Stats feature")
Fixes: c28e6f06ff ("ath10k: fix sanity check on enabling btcoex via debugfs")
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fixes checkpatch warning:
drivers/net/wireless/ath/ath10k/wmi.c:5800: Prefer ether_addr_copy() over memcpy() if the Ethernet addresses are __aligned(2)
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fixes checkpatch warnings:
drivers/net/wireless/ath/ath10k/mac.c:452: Prefer ether_addr_equal() or ether_addr_equal_unaligned() over memcmp()
drivers/net/wireless/ath/ath10k/mac.c:455: Prefer ether_addr_equal() or ether_addr_equal_unaligned() over memcmp()
drivers/net/wireless/ath/ath10k/txrx.c:133: Prefer ether_addr_equal() or ether_addr_equal_unaligned() over memcmp()
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fixes checkpatch warnings:
drivers/net/wireless/ath/ath10k/htt.h:1477: Prefer kernel type 'u64' over 'u_int64_t'
drivers/net/wireless/ath/ath10k/htt.h:1480: Prefer kernel type 'u64' over 'u_int64_t'
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fix checkpatch warnings about use of spaces with operators:
spaces preferred around that '*' (ctx:VxV)
This has been recently added to checkpatch.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
MSI-X is never well-tested, might contain bugs and generally isn't
really all that useful to maintain. Also ath10k is mainly used with
shared/singly-MSI interrupt systems. Hence removing MSI range support.
This change will be useful for further cleanup in copy engine lock
and to add NAPI support.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
10.4 firmware has addeded set_tsf vdev parameter,
hence enable it.
set_tsf function can be used to shift TBTT that will
help avoid its clockdrift which happens when beacons
are collided.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Update 10.4 WMI vdev param to sync to current 10.4 firmware
as of 2/23/2016.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
10.2.4.70.24 firmware introduces new feature to set TSF
via vdev parameter, hence implement relevant function.
set_tsf function can be used to shift TBTT that will
help avoid its clockdrift which happens when beacons
are collided.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This will help anyone trying to use the ack-rssi reporting
feature with the host-specified TX-rate option in 10.4 firmware.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This enum is already perfectly aliased to enum nl80211_band, and
the only reason for it is that we get IEEE80211_NUM_BANDS out of
it. There's no really good reason to not declare the number of
bands in nl80211 though, so do that and remove the cfg80211 one.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Major changes:
iwlwifi
* support for Link Quality measurement
* more work 9000 devices and MSIx
* continuation of the Dynamic Queue Allocation work
* make the paging less memory hungry
* 9000 new Rx path
* removal of IWLWIFI_UAPSD Kconfig option
ath10k
* implement push-pull tx model using mac80211 software queuing support
* enable scan in AP mode (NL80211_FEATURE_AP_SCAN)
wil6210
* add basic PBSS (Personal Basic Service Set) support
* add initial P2P support
* add oob_mode module parameter
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJXC5ZnAAoJEG4XJFUm622bcLgIAKxTHWfcirfNpzLg39gfR/jx
vWTX8YifGdZUuQuaEJhc7pPZ6eiTyMlRLZsu9JDT0LErM6uwPKSOXkogzfiSFG00
ntXGOWfQlGdyFyQshOoHWlXSkfE7bBWpLiROgk7dS2oyObQr2ETBT/yVd1bkP6Ka
g13sgzM/a3CbxaZSllaK0S/YPQ6JhXlbeWotqOqE4SotYQD2QfLkYJiXSFRXNcQl
OWDPCTjI3yybOVRLTnLMn2CoWrRqtUElwXaWBKJPhgY3EyxlU6R6UPw8OL8DvXIw
EedpflIekKahwZJbipqdkKbhpxinUAa9kPsSkfCtlPJQWsiQvdwpG7R5KQmJ8Lc=
=A2Lw
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2016-04-11' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers patches for 4.7
Major changes:
iwlwifi
* support for Link Quality measurement
* more work 9000 devices and MSIx
* continuation of the Dynamic Queue Allocation work
* make the paging less memory hungry
* 9000 new Rx path
* removal of IWLWIFI_UAPSD Kconfig option
ath10k
* implement push-pull tx model using mac80211 software queuing support
* enable scan in AP mode (NL80211_FEATURE_AP_SCAN)
wil6210
* add basic PBSS (Personal Basic Service Set) support
* add initial P2P support
* add oob_mode module parameter
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Decrement num_mpdus_ready only when rx amsdu is processed successfully.
Not doing so, will result in leak and impact stabilty under low memory
cases. Also commit 3128b3d8a2 ("ath10k: speedup htt rx descriptor
processing for rx_ind") missed to removed unused skb list rx_q.
Fixes: 3128b3d8a2 ("ath10k: speedup htt rx descriptor processing for rx_ind")
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
qca99x0 and qca4019 solutions limit probe responses transmissions.
Logging warning message for each probe response drop is flooding
kernel log unnecessary with " failed to increase tx mgmt pending
count: -16, dropping". Hence reducing log level to debug.
Reported-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
pre-calibration is meant for qca4019 which contains only caldata
whereas calibration file is used by ar9888 and qca99x0 that contains
both board data and caldata. So by definition both pre-cal-file and
cal-file can not coexist. Keeping them in shared memory (union), is
breaking boot sequence of qca99x0. Fix it by storing both binaries
in separate memories. This issue is reported in ipq8064 platform which
includes caldata in flash memory.
Fixes: 3d9195ea19 ("ath10k: incorporate qca4019 cal data download sequence")
Reported-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When HW crypto is used, there's no need for the CCMP/GCMP MIC to
be available to mac80211, and the hardware might have removed it
already after checking. The MIC is also useless to have when the
frame is already decrypted, so allow indicating that it's not
present.
Since we are running out of bits in mac80211_rx_flags, make
the flags field a u64.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Check and parse Rx MAC timestamp when firmware sets its flag
to status variable.
10.4 firmware adds it in Rx beacon frame only at this moment.
Drivers and mac80211 may utilize it to detect such clockdrift
or beacon collision and use the result for beacon collision
avoidance.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Since tx completion and rx indication processing are moved out
of txrx tasklet and rx ring lock contention also removed from txrx
for rx_ind messages, it would be efficient to combine both replenish
and txrx tasks. Refill threshold is adjusted for both AP135 and AP148
(low and high end systems). With this adjustment in AP135, TCP DL is
improved from 603 Mbps to 620 Mbps and UDP DL is improved from 758 Mbps
to 803 Mbps. Also no watchdog are observed on UDP BiDi.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Whenever htt rx indication i.e target to host messages are received
on rx copy engine (CE5), the message will be freed after processing
the response. Then CE 5 will be refilled with new descriptors at
post rx processing. This memory alloc and free operations can be avoided
by reusing the same descriptors.
During CE pipe allocation, full ring is not initialized i.e n-1 entries
are filled up. So for CE 5 full ring should be filled up to reuse
descriptors. Moreover CE 5 write index will be updated in single shot
instead of incremental access. This could avoid multiple pci_write and
ce_ring access. From experiments, It improves CPU usage by ~3% in IPQ4019
platform.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The physical address necessary to unmap DMA ('bufferp') is stored
in ath10k_skb_cb as 'paddr'. For diag register read and write
operations, 'paddr' is stored in transfer context. ath10k doesn't rely
on the meta/transfer_id. So the unused output arguments {bufferp, nbytesp
and transfer_idp} are removed from CE recv_next completion.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Except qca61x4 family chips (qca6164, qca6174), copy engine 5 is used
for receiving target to host htt messages. In follow up patch, CE5
descriptors will be reused. In such case, same API can not be used as
htc layer callback where the response messages will be freed at the end.
Hence register new API for HTC layer that free up received message and
keep the message handler common for both HTC and HIF layers.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
