Ie., the difference between partial and all clearing doesn't
exists anymore since the SACK optimizations got dropped by
an sacktag rewrite.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch consolidates the code common to TCP and CCID-2:
* TCP uses RFC 3390 in a packet-oriented manner (tcp_input.c) and
* CCID-2 uses RFC 3390 in packet-oriented manner (RFC 4341).
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Some duplicated code lying around. Located with my suffix tree
tool.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Large block of code duplication removed.
Sadly, the return value thing is a bit tricky here but it
seems the most sensible way to return positive from validator
on success rather than negative.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removes legacy reinvent-the-wheel type thing. The generic
machinery integrates much better to automated debugging aids
such as kerneloops.org (and others), and is unambiguous due to
better naming. Non-intuively BUG_TRAP() is actually equal to
WARN_ON() rather than BUG_ON() though some might actually be
promoted to BUG_ON() but I left that to future.
I could make at least one BUILD_BUG_ON conversion.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is based upon an excellent bug report from Eric Dumazet.
tcp_ack() should clear ->icsk_probes_out even if there are packets
outstanding. Otherwise if we get a sequence of ACKs while we do have
packets outstanding over and over again, we'll never clear the
probes_out value and eventually think the connection is too sick and
we'll reset it.
This appears to be some "optimization" added to tcp_ack() in the 2.4.x
timeframe. In 2.2.x, probes_out is pretty much always cleared by
tcp_ack().
Here is Eric's original report:
----------------------------------------
Apparently, we can in some situations reset TCP connections in a couple of seconds when some frames are lost.
In order to reproduce the problem, please try the following program on linux-2.6.25.*
Setup some iptables rules to allow two frames per second sent on loopback interface to tcp destination port 12000
iptables -N SLOWLO
iptables -A SLOWLO -m hashlimit --hashlimit 2 --hashlimit-burst 1 --hashlimit-mode dstip --hashlimit-name slow2 -j ACCEPT
iptables -A SLOWLO -j DROP
iptables -A OUTPUT -o lo -p tcp --dport 12000 -j SLOWLO
Then run the attached program and see the output :
# ./loop
State Recv-Q Send-Q Local Address:Port Peer Address:Port
ESTAB 0 40 127.0.0.1:54455 127.0.0.1:12000 timer:(persist,200ms,1)
State Recv-Q Send-Q Local Address:Port Peer Address:Port
ESTAB 0 40 127.0.0.1:54455 127.0.0.1:12000 timer:(persist,200ms,3)
State Recv-Q Send-Q Local Address:Port Peer Address:Port
ESTAB 0 40 127.0.0.1:54455 127.0.0.1:12000 timer:(persist,200ms,5)
State Recv-Q Send-Q Local Address:Port Peer Address:Port
ESTAB 0 40 127.0.0.1:54455 127.0.0.1:12000 timer:(persist,200ms,7)
State Recv-Q Send-Q Local Address:Port Peer Address:Port
ESTAB 0 40 127.0.0.1:54455 127.0.0.1:12000 timer:(persist,200ms,9)
State Recv-Q Send-Q Local Address:Port Peer Address:Port
ESTAB 0 40 127.0.0.1:54455 127.0.0.1:12000 timer:(persist,200ms,11)
State Recv-Q Send-Q Local Address:Port Peer Address:Port
ESTAB 0 40 127.0.0.1:54455 127.0.0.1:12000 timer:(persist,201ms,13)
State Recv-Q Send-Q Local Address:Port Peer Address:Port
ESTAB 0 40 127.0.0.1:54455 127.0.0.1:12000 timer:(persist,188ms,15)
write(): Connection timed out
wrote 890 bytes but was interrupted after 9 seconds
ESTAB 0 0 127.0.0.1:12000 127.0.0.1:54455
Exiting read() because no data available (4000 ms timeout).
read 860 bytes
While this tcp session makes progress (sending frames with 50 bytes of payload, every 500ms), linux tcp stack decides to reset it, when tcp_retries 2 is reached (default value : 15)
tcpdump :
15:30:28.856695 IP 127.0.0.1.56554 > 127.0.0.1.12000: S 33788768:33788768(0) win 32792 <mss 16396,nop,nop,sackOK,nop,wscale 7>
15:30:28.856711 IP 127.0.0.1.12000 > 127.0.0.1.56554: S 33899253:33899253(0) ack 33788769 win 32792 <mss 16396,nop,nop,sackOK,nop,wscale 7>
15:30:29.356947 IP 127.0.0.1.56554 > 127.0.0.1.12000: P 1:61(60) ack 1 win 257
15:30:29.356966 IP 127.0.0.1.12000 > 127.0.0.1.56554: . ack 61 win 257
15:30:29.866415 IP 127.0.0.1.56554 > 127.0.0.1.12000: P 61:111(50) ack 1 win 257
15:30:29.866427 IP 127.0.0.1.12000 > 127.0.0.1.56554: . ack 111 win 257
15:30:30.366516 IP 127.0.0.1.56554 > 127.0.0.1.12000: P 111:161(50) ack 1 win 257
15:30:30.366527 IP 127.0.0.1.12000 > 127.0.0.1.56554: . ack 161 win 257
15:30:30.876196 IP 127.0.0.1.56554 > 127.0.0.1.12000: P 161:211(50) ack 1 win 257
15:30:30.876207 IP 127.0.0.1.12000 > 127.0.0.1.56554: . ack 211 win 257
15:30:31.376282 IP 127.0.0.1.56554 > 127.0.0.1.12000: P 211:261(50) ack 1 win 257
15:30:31.376290 IP 127.0.0.1.12000 > 127.0.0.1.56554: . ack 261 win 257
15:30:31.885619 IP 127.0.0.1.56554 > 127.0.0.1.12000: P 261:311(50) ack 1 win 257
15:30:31.885631 IP 127.0.0.1.12000 > 127.0.0.1.56554: . ack 311 win 257
15:30:32.385705 IP 127.0.0.1.56554 > 127.0.0.1.12000: P 311:361(50) ack 1 win 257
15:30:32.385715 IP 127.0.0.1.12000 > 127.0.0.1.56554: . ack 361 win 257
15:30:32.895249 IP 127.0.0.1.56554 > 127.0.0.1.12000: P 361:411(50) ack 1 win 257
15:30:32.895266 IP 127.0.0.1.12000 > 127.0.0.1.56554: . ack 411 win 257
15:30:33.395341 IP 127.0.0.1.56554 > 127.0.0.1.12000: P 411:461(50) ack 1 win 257
15:30:33.395351 IP 127.0.0.1.12000 > 127.0.0.1.56554: . ack 461 win 257
15:30:33.918085 IP 127.0.0.1.56554 > 127.0.0.1.12000: P 461:511(50) ack 1 win 257
15:30:33.918096 IP 127.0.0.1.12000 > 127.0.0.1.56554: . ack 511 win 257
15:30:34.418163 IP 127.0.0.1.56554 > 127.0.0.1.12000: P 511:561(50) ack 1 win 257
15:30:34.418172 IP 127.0.0.1.12000 > 127.0.0.1.56554: . ack 561 win 257
15:30:34.927685 IP 127.0.0.1.56554 > 127.0.0.1.12000: P 561:611(50) ack 1 win 257
15:30:34.927698 IP 127.0.0.1.12000 > 127.0.0.1.56554: . ack 611 win 257
15:30:35.427757 IP 127.0.0.1.56554 > 127.0.0.1.12000: P 611:661(50) ack 1 win 257
15:30:35.427766 IP 127.0.0.1.12000 > 127.0.0.1.56554: . ack 661 win 257
15:30:35.937359 IP 127.0.0.1.56554 > 127.0.0.1.12000: P 661:711(50) ack 1 win 257
15:30:35.937376 IP 127.0.0.1.12000 > 127.0.0.1.56554: . ack 711 win 257
15:30:36.437451 IP 127.0.0.1.56554 > 127.0.0.1.12000: P 711:761(50) ack 1 win 257
15:30:36.437464 IP 127.0.0.1.12000 > 127.0.0.1.56554: . ack 761 win 257
15:30:36.947022 IP 127.0.0.1.56554 > 127.0.0.1.12000: P 761:811(50) ack 1 win 257
15:30:36.947039 IP 127.0.0.1.12000 > 127.0.0.1.56554: . ack 811 win 257
15:30:37.447135 IP 127.0.0.1.56554 > 127.0.0.1.12000: P 811:861(50) ack 1 win 257
15:30:37.447203 IP 127.0.0.1.12000 > 127.0.0.1.56554: . ack 861 win 257
15:30:41.448171 IP 127.0.0.1.12000 > 127.0.0.1.56554: F 1:1(0) ack 861 win 257
15:30:41.448189 IP 127.0.0.1.56554 > 127.0.0.1.12000: R 33789629:33789629(0) win 0
Source of program :
/*
* small producer/consumer program.
* setup a listener on 127.0.0.1:12000
* Forks a child
* child connect to 127.0.0.1, and sends 10 bytes on this tcp socket every 100 ms
* Father accepts connection, and read all data
*/
#include <sys/types.h>
#include <sys/socket.h>
#include <netinet/in.h>
#include <unistd.h>
#include <stdio.h>
#include <time.h>
#include <sys/poll.h>
int port = 12000;
char buffer[4096];
int main(int argc, char *argv[])
{
int lfd = socket(AF_INET, SOCK_STREAM, 0);
struct sockaddr_in socket_address;
time_t t0, t1;
int on = 1, sfd, res;
unsigned long total = 0;
socklen_t alen = sizeof(socket_address);
pid_t pid;
time(&t0);
socket_address.sin_family = AF_INET;
socket_address.sin_port = htons(port);
socket_address.sin_addr.s_addr = htonl(INADDR_LOOPBACK);
if (lfd == -1) {
perror("socket()");
return 1;
}
setsockopt(lfd, SOL_SOCKET, SO_REUSEADDR, &on, sizeof(int));
if (bind(lfd, (struct sockaddr *)&socket_address, sizeof(socket_address)) == -1) {
perror("bind");
close(lfd);
return 1;
}
if (listen(lfd, 1) == -1) {
perror("listen()");
close(lfd);
return 1;
}
pid = fork();
if (pid == 0) {
int i, cfd = socket(AF_INET, SOCK_STREAM, 0);
close(lfd);
if (connect(cfd, (struct sockaddr *)&socket_address, sizeof(socket_address)) == -1) {
perror("connect()");
return 1;
}
for (i = 0 ; ;) {
res = write(cfd, "blablabla\n", 10);
if (res > 0) total += res;
else if (res == -1) {
perror("write()");
break;
} else break;
usleep(100000);
if (++i == 10) {
system("ss -on dst 127.0.0.1:12000");
i = 0;
}
}
time(&t1);
fprintf(stderr, "wrote %lu bytes but was interrupted after %g seconds\n", total, difftime(t1, t0));
system("ss -on | grep 127.0.0.1:12000");
close(cfd);
return 0;
}
sfd = accept(lfd, (struct sockaddr *)&socket_address, &alen);
if (sfd == -1) {
perror("accept");
return 1;
}
close(lfd);
while (1) {
struct pollfd pfd[1];
pfd[0].fd = sfd;
pfd[0].events = POLLIN;
if (poll(pfd, 1, 4000) == 0) {
fprintf(stderr, "Exiting read() because no data available (4000 ms timeout).\n");
break;
}
res = read(sfd, buffer, sizeof(buffer));
if (res > 0) total += res;
else if (res == 0) break;
else perror("read()");
}
fprintf(stderr, "read %lu bytes\n", total);
close(sfd);
return 0;
}
----------------------------------------
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove redundant checks when setting eff_sacks and make the number of SACKs a
compile time constant. Now that the options code knows how many SACK blocks can
fit in the header, we don't need to have the SACK code guessing at it.
Signed-off-by: Adam Langley <agl@imperialviolet.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the metrics (RTT, RTTVAR and RTAX_RTO_MIN) are stored in
kernel units (jiffies) and this leaks out through the netlink API to
user space where the units for jiffies are unknown.
This patches changes the kernel to convert to/from milliseconds. This
changes the ABI, but milliseconds seemed like the most natural unit
for these parameters. Values available via syscall in
/proc/net/rt_cache and netlink will be in milliseconds.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These places have a tcp_sock, but we'd prefer the sock itself to
get net from it. Fortunately, tcp_sk macro is just a type cast, so
this replace is really cheap.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Same as before - the sock is always there to get the net from,
but there are also some places with the net already saved on
the stack.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are some places in TCP that select one MIB index to
bump snmp statistics like this:
if (<something>)
NET_INC_STATS_BH(<some_id>);
else if (<something_else>)
NET_INC_STATS_BH(<some_other_id>);
...
else
NET_INC_STATS_BH(<default_id>);
or in a more tricky but still similar way.
On the other hand, this NET_INC_STATS_BH is a camouflaged
increment of percpu variable, which is not that small.
Factoring those cases out de-bloats 235 bytes on non-preemptible
i386 config and drives parts of the code into 80 columns.
add/remove: 0/0 grow/shrink: 0/7 up/down: 0/-235 (-235)
function old new delta
tcp_fastretrans_alert 1437 1424 -13
tcp_dsack_set 137 124 -13
tcp_xmit_retransmit_queue 690 676 -14
tcp_try_undo_recovery 283 265 -18
tcp_sacktag_write_queue 1550 1515 -35
tcp_update_reordering 162 106 -56
tcp_retransmit_timer 990 904 -86
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts two changesets, ec3c0982a2
("[TCP]: TCP_DEFER_ACCEPT updates - process as established") and
the follow-on bug fix 9ae27e0adb
("tcp: Fix slab corruption with ipv6 and tcp6fuzz").
This change causes several problems, first reported by Ingo Molnar
as a distcc-over-loopback regression where connections were getting
stuck.
Ilpo Järvinen first spotted the locking problems. The new function
added by this code, tcp_defer_accept_check(), only has the
child socket locked, yet it is modifying state of the parent
listening socket.
Fixing that is non-trivial at best, because we can't simply just grab
the parent listening socket lock at this point, because it would
create an ABBA deadlock. The normal ordering is parent listening
socket --> child socket, but this code path would require the
reverse lock ordering.
Next is a problem noticed by Vitaliy Gusev, he noted:
----------------------------------------
>--- a/net/ipv4/tcp_timer.c
>+++ b/net/ipv4/tcp_timer.c
>@@ -481,6 +481,11 @@ static void tcp_keepalive_timer (unsigned long data)
> goto death;
> }
>
>+ if (tp->defer_tcp_accept.request && sk->sk_state == TCP_ESTABLISHED) {
>+ tcp_send_active_reset(sk, GFP_ATOMIC);
>+ goto death;
Here socket sk is not attached to listening socket's request queue. tcp_done()
will not call inet_csk_destroy_sock() (and tcp_v4_destroy_sock() which should
release this sk) as socket is not DEAD. Therefore socket sk will be lost for
freeing.
----------------------------------------
Finally, Alexey Kuznetsov argues that there might not even be any
real value or advantage to these new semantics even if we fix all
of the bugs:
----------------------------------------
Hiding from accept() sockets with only out-of-order data only
is the only thing which is impossible with old approach. Is this really
so valuable? My opinion: no, this is nothing but a new loophole
to consume memory without control.
----------------------------------------
So revert this thing for now.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes CVS keywords that weren't updated for a long time
from comments.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This bug is able to corrupt fackets_out in very rare cases.
In order for this to cause corruption:
1) DSACK in the middle of previous SACK block must be generated.
2) In order to take that particular branch, part or all of the
DSACKed segment must already be SACKed so that we have that
in cache in the first place.
3) The new info must be top enough so that fackets_out will be
updated on this iteration.
...then fack_count is updated while skb wasn't, then we walk again
that particular segment thus updating fack_count twice for
a single skb and finally that value is assigned to fackets_out
by tcp_sacktag_one.
It is safe to call tcp_sacktag_one just once for a segment (at
DSACK), no need to call again for plain SACK.
Potential problem of the miscount are limited to premature entry
to recovery and to inflated reordering metric (which could even
cancel each other out in the most the luckiest scenarios :-)).
Both are quite insignificant in worst case too and there exists
also code to reset them (fackets_out once sacked_out becomes zero
and reordering metric on RTO).
This has been reported by a number of people, because it occurred
quite rarely, it has been very evasive. Andy Furniss was able to
get it to occur couple of times so that a bit more info was
collected about the problem using a debug patch, though it still
required lot of checking around. Thanks also to others who have
tried to help here.
This is listed as Bugzilla #10346. The bug was introduced by
me in commit 68f8353b48 ([TCP]: Rewrite SACK block processing &
sack_recv_cache use), I probably thought back then that there's
need to scan that entry twice or didn't dare to make it go
through it just once there. Going through twice would have
required restoring fack_count after the walk but as noted above,
I chose to drop the additional walk step altogether here.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible that this skip path causes TCP to end up into an
invalid state where ca_state was left to CA_Open while some
segments already came into sacked_out. If next valid ACK doesn't
contain new SACK information TCP fails to enter into
tcp_fastretrans_alert(). Thus at least high_seq is set
incorrectly to a too high seqno because some new data segments
could be sent in between (and also, limited transmit is not
being correctly invoked there). Reordering in both directions
can easily cause this situation to occur.
I guess we would want to use tcp_moderate_cwnd(tp) there as well
as it may be possible to use this to trigger oversized burst to
network by sending an old ACK with huge amount of SACK info, but
I'm a bit unsure about its effects (mainly to FlightSize), so to
be on the safe side I just currently fixed it minimally to keep
TCP's state consistent (obviously, such nasty ACKs have been
possible this far). Though it seems that FlightSize is already
underestimated by some amount, so probably on the long term we
might want to trigger recovery there too, if appropriate, to make
FlightSize calculation to resemble reality at the time when the
losses where discovered (but such change scares me too much now
and requires some more thinking anyway how to do that as it
likely involves some code shuffling).
This bug was found by Brian Vowell while running my TCP debug
patch to find cause of another TCP issue (fackets_out
miscount).
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
If receiver consumes segments successfully only in-order, FRTO
fallback to conventional recovery produces RTO loop because
FRTO's forward transmissions will always get dropped and need to
be resent, yet by default they're not marked as lost (which are
the only segments we will retransmit in CA_Loss).
Price to pay about this is occassionally unnecessarily
retransmitting the forward transmission(s). SACK blocks help
a bit to avoid this, so it's mainly a concern for NewReno case
though SACK is not fully immune either.
This change has a side-effect of fixing SACKFRTO problem where
it didn't have snd_nxt of the RTO time available anymore when
fallback become necessary (this problem would have only occured
when RTO would occur for two or more segments and ECE arrives
in step 3; no need to figure out how to fix that unless the
TODO item of selective behavior is considered in future).
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Reported-by: Damon L. Chesser <damon@damtek.com>
Tested-by: Damon L. Chesser <damon@damtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems that commit 009a2e3e4e ("[TCP] FRTO: Improve
interoperability with other undo_marker users") run into
another land-mine which caused fallback to conventional
recovery to break:
1. Cumulative ACK arrives after FRTO retransmission
2. tcp_try_to_open sees zero retrans_out, clears retrans_stamp
which should be kept like in CA_Loss state it would be
3. undo_marker change allowed tcp_packet_delayed to return
true because of the cleared retrans_stamp once FRTO is
terminated causing LossUndo to occur, which means all loss
markings FRTO made are reverted.
This means that the conventional recovery basically recovered
one loss per RTT, which is not that efficient. It was quite
unobvious that the undo_marker change broken something like
this, I had a quite long session to track it down because of
the non-intuitiviness of the bug (luckily I had a trivial
reproducer at hand and I was also able to learn to use kprobes
in the process as well :-)).
This together with the NewReno+FRTO fix and FRTO in-order
workaround this fixes Damon's problems, this and the first
mentioned are enough to fix Bugzilla #10063.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Reported-by: Damon L. Chesser <damon@damtek.com>
Tested-by: Damon L. Chesser <damon@damtek.com>
Tested-by: Sebastian Hyrwall <zibbe@cisko.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Note: there's actually another bug in FRTO's SACK variant, which
is the causing failure in NewReno case because of the error
that's fixed here. I'll fix the SACK case separately (it's
a separate bug really, though related, but in order to fix that
I need to audit tp->snd_nxt usage a bit).
There were two places where SACK variant of FRTO is getting
incorrectly used even if SACK wasn't negotiated by the TCP flow.
This leads to incorrect setting of frto_highmark with NewReno
if a previous recovery was interrupted by another RTO.
An eventual fallback to conventional recovery then incorrectly
considers one or couple of segments as forward transmissions
though they weren't, which then are not LOST marked during
fallback making them "non-retransmittable" until the next RTO.
In a bad case, those segments are really lost and are the only
one left in the window. Thus TCP needs another RTO to continue.
The next FRTO, however, could again repeat the same events
making the progress of the TCP flow extremely slow.
In order for these events to occur at all, FRTO must occur
again in FRTOs step 3 while the key segments must be lost as
well, which is not too likely in practice. It seems to most
frequently with some small devices such as network printers
that *seem* to accept TCP segments only in-order. In cases
were key segments weren't lost, things get automatically
resolved because those wrongly marked segments don't need to be
retransmitted in order to continue.
I found a reproducer after digging up relevant reports (few
reports in total, none at netdev or lkml I know of), some
cases seemed to indicate middlebox issues which seems now
to be a false assumption some people had made. Bugzilla
#10063 _might_ be related. Damon L. Chesser <damon@damtek.com>
had a reproducable case and was kind enough to tcpdump it
for me. With the tcpdump log it was quite trivial to figure
out.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are functions to refer to the value of dst->metric[THE_METRIC-1]
directly without use of a inline function "dst_metric" defined in
net/dst.h.
The following patch changes them to use the inline function
consistently.
Signed-off-by: Satoru SATOH <satoru.satoh@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
This fixes a regression added by ec3c0982a2
("[TCP]: TCP_DEFER_ACCEPT updates - process as established")
tcp_v6_do_rcv()->tcp_rcv_established(), the latter goes to step5, where
eventually skb can be freed via tcp_data_queue() (drop: label), then if
check for tcp_defer_accept_check() returns true and thus
tcp_rcv_established() returns -1, which forces tcp_v6_do_rcv() to jump
to reset: label, which in turn will pass through discard: label and free
the same skb again.
Tested by Eric Sesterhenn.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-By: Patrick McManus <mcmanus@ducksong.com>
Returns non-zero if tp->out_of_order_queue was seen non-empty.
This allows tcp_try_rmem_schedule() to return early.
Signed-off-by: Vitaliy Gusev <vgusev@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_prune_queue() doesn't prune an out-of-order queue at all.
Therefore sk_rmem_schedule() can fail but the out-of-order queue isn't
pruned . This can lead to tcp deadlock state if the next two
conditions are held:
1. There are a sequence hole between last received in
order segment and segments enqueued to the out-of-order queue.
2. Size of all segments in the out-of-order queue is more than tcp_mem[2].
Signed-off-by: Vitaliy Gusev <vgusev@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This expresses __skb_append in terms of __skb_queue_after, exploiting that
__skb_append(old, new, list) = __skb_queue_after(list, old, new).
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
MTU probe can cause some remedies for FRTO because the normal
packet ordering may be violated allowing FRTO to make a wrong
decision (it might not be that serious threat for anything
though). Thus it's safer to not run FRTO while MTU probe is
underway.
It seems that the basic FRTO variant should also look for an
skb at probe_seq.start to check if that's retransmitted one
but I didn't implement it now (plain seqno in window check
isn't robust against wraparounds).
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes Bugzilla #10384
tcp_simple_retransmit does L increment without any checking
whatsoever for overflowing S+L when Reno is in use.
The simplest scenario I can currently think of is rather
complex in practice (there might be some more straightforward
cases though). Ie., if mss is reduced during mtu probing, it
may end up marking everything lost and if some duplicate ACKs
arrived prior to that sacked_out will be non-zero as well,
leading to S+L > packets_out, tcp_clean_rtx_queue on the next
cumulative ACK or tcp_fastretrans_alert on the next duplicate
ACK will fix the S counter.
More straightforward (but questionable) solution would be to
just call tcp_reset_reno_sack() in tcp_simple_retransmit but
it would negatively impact the probe's retransmission, ie.,
the retransmissions would not occur if some duplicate ACKs
had arrived.
So I had to add reno sacked_out reseting to CA_Loss state
when the first cumulative ACK arrives (this stale sacked_out
might actually be the explanation for the reports of left_out
overflows in kernel prior to 2.6.23 and S+L overflow reports
of 2.6.24). However, this alone won't be enough to fix kernel
before 2.6.24 because it is building on top of the commit
1b6d427bb7 ([TCP]: Reduce sacked_out with reno when purging
write_queue) to keep the sacked_out from overflowing.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Reported-by: Alessandro Suardi <alessandro.suardi@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes a long-standing bug which makes NewReno recovery crippled.
With GSO the whole head skb was marked as LOST which is in
violation of NewReno procedure that only wants to mark one packet
and ended up breaking our TCP code by causing counter overflow
because our code was built on top of assumption about valid
NewReno procedure. This manifested as triggering a WARN_ON for
the overflow in a number of places.
It seems relatively safe alternative to just do nothing if
tcp_fragment fails due to oom because another duplicate ACK is
likely to be received soon and the fragmentation will be retried.
Special thanks goes to Soeren Sonnenburg <kernel@nn7.de> who was
lucky enough to be able to reproduce this so that the warning
for the overflow was hit. It's not as easy task as it seems even
if this bug happens quite often because the amount of outstanding
data is pretty significant for the mismarkings to lead to an
overflow.
Because it's very late in 2.6.25-rc cycle (if this even makes in
time), I didn't want to touch anything with SACK enabled here.
Fragmenting might be useful for it as well but it's more or less
a policy decision rather than mandatory fix. Thus there's no need
to rush and we can postpone considering tcp_fragment with SACK
for 2.6.26.
In 2.6.24 and earlier, this very same bug existed but the effect
is slightly different because of a small changes in the if
conditions that fit to the patch's context. With them nothing
got lost marker and thus no retransmissions happened.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
The fast retransmission can be forced locally to the rfc3517
branch in tcp_update_scoreboard instead of making such fragile
constructs deeper in tcp_mark_head_lost.
This is necessary for the next patch which must not have
loopholes for cnt > packets check. As one can notice,
readability got some improvements too because of this :-).
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change TCP_DEFER_ACCEPT implementation so that it transitions a
connection to ESTABLISHED after handshake is complete instead of
leaving it in SYN-RECV until some data arrvies. Place connection in
accept queue when first data packet arrives from slow path.
Benefits:
- established connection is now reset if it never makes it
to the accept queue
- diagnostic state of established matches with the packet traces
showing completed handshake
- TCP_DEFER_ACCEPT timeouts are expressed in seconds and can now be
enforced with reasonable accuracy instead of rounding up to next
exponential back-off of syn-ack retry.
Signed-off-by: Patrick McManus <mcmanus@ducksong.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Updated to incorporate Eric's suggestion of using a per cpu buffer
rather than allocating on the stack. Just a two line change, but will
resend in it's entirety.
Signed-off-by: Glenn Griffin <ggriffin.kernel@gmail.com>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
It makes fackets_out to grow too slowly compared with the
real write queue.
This shouldn't cause those BUG_TRAP(packets <= tp->packets_out)
to trigger but how knows how such inconsistent fackets_out
affects here and there around TCP when everything is nowadays
assuming accurate fackets_out. So lets see if this silences
them all.
Reported by Guillaume Chazarain <guichaz@gmail.com>.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
NewReno should add cnt per skb (as with FACK) instead of depending on
SACKED_ACKED bits which won't be set with it at all. Effectively,
NewReno should always exists after the first iteration anyway (or
immediately if there's already head in lost_out.
This was fixed earlier in net-2.6.25 but got reverted among other
stuff and I didn't notice that this is still necessary (actually
wasn't even considering this case while trying to figure out the
reports because I lived with different kind of code than it in reality
was).
This should solve the WARN_ONs in TCP code that as a result of this
triggered multiple times in every place we check for this invariant.
Special thanks to Dave Young <hidave.darkstar@gmail.com> and Krishna
Kumar2 <krkumar2@in.ibm.com> for trying with my debug patches.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Tested-by: Dave Young <hidave.darkstar@gmail.com>
Tested-by: Krishna Kumar2 <krkumar2@in.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removed case indentation level & combined some nested ifs, mostly
within 80 lines now. This is a leftover from indent patch, it
just had to be done manually to avoid messing it up completely.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
These were manually selected from indent's results which as is
are too noisy to be of any use without human reason. In addition,
some extra newlines between function and its comment were removed
too.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
The snd_up check should be enough. I suspect this has been
there to provide a minor optimization in clean_rtx_queue which
used to have a small if (!->sacked) block which could skip
snd_up check among the other work.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
SACK reneging can be precalculated to a FLAG in clean_rtx_queue
which has the right skb looked up. This will help a bit in
future because skb->sacked access will be changed eventually,
changing it already won't hurt any.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
