No functional change, move bitfield calculations to macro
definitions with added clock rate argument, which are in turn defined
by new common SLCTAC_CLOCKS(c, n, s) macro definition.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Use the nand_check_erased_ecc_chunk() function to test if the ECC error
was triggered by an erased page containing a few bitflips.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
sunxi_nfc_user_data_to_buf() is exposed as an inline function, replace the
NFC_BUF_TO_USER_DATA() macro by an inline function to be consistent.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The ECC engine is protecting a few OOB bytes. Retrieve them from the
USER_DATA register instead of reading them in raw mode (ie without the ECC
protection).
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add helper functions to factorize the code dealing extra OOB bytes in the
normal and syndrome ECC implementations.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The sunxi_nfc_hw_ecc_read/write_chunk() functions have been created to
factorize the code in the normal and syndrome ECC implementation.
Make use of them where appropriate.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The logic behind normal and syndrome ECC handling is pretty much the same,
the only difference is the ECC bytes placement.
Create two functions to read/write ECC chunks. Those functions will later
be used by the sunxi_nfc_hw_ecc_read/write_page() and
sunxi_nfc_hw_syndrome_ecc_read/write_page() functions.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The code used to enable/disable the hardware ECC engine is repeated in a
lot of places. Create two functions to avoid code duplication.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The ->init_size() hook was introduced to let NAND controller drivers
support NAND devices that could not be described in the nand_ids table.
Since then, the core has added support for extended-id parsing and
full-id description, thus allowing to describe pretty much all existing
NANDs.
Moreover, this hook is not used by any mainline driver, and should not be
used by new drivers, because detecting the NAND chip is not something
controller specific.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
These really aren't needed, especially now that we embed the soc struct
in our private struct, so we can stash things there if needed.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Suffix mask macros with _MSK and add new helper macros to avoid manually
shifting values.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This must have been implicitly included on the builds I tested. Reported
by numerous test bots:
drivers/mtd/nand/vf610_nfc.c: In function 'vf610_nfc_resume':
drivers/mtd/nand/vf610_nfc.c:660:2: error: implicit declaration of function 'pinctrl_pm_select_default_state' [-Werror=implicit-function-declaration]
pinctrl_pm_select_default_state(dev);
^
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Stefan Agner <stefan@agner.ch>
If we fail to allocate a partition structure in the middle of the partition
creation process, the already allocated partitions are never removed, which
means they are still present in the partition list and their resources are
never freed.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: stable@vger.kernel.org
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This reverts commit 7827e3acad.
There are some 64-bit arithmetic issues on some architectures, so let's
wait until we get a better patch for this.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
We should prevent user to erasing mtd device with
an unaligned offset or length.
Signed-off-by: Dongsheng Yang <yangds.fnst@cn.fujitsu.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This adds hardware ECC support using the BCH encoder in the NFC IP.
The ECC encoder supports up to 32-bit correction by using 60 error
correction bytes. There is no sub-page ECC step, ECC is calculated
always across the whole page (up to 2k pages).
Limitations:
- HW ECC: Only 2K page with 64+ OOB.
- HW ECC: Only 24 and 32-bit error correction implemented.
Raw writes have been tested using the generic nand_write_page_raw
implementation. However, raw reads are currently not possible
because the controller need to know whether we are going to use
the ECC mode already at NAND_CMD_READ0 command time. At this point
we do not have the information whether it is a raw read or a
regular read at driver level...
Signed-off-by: Bill Pringlemeir <bpringlemeir@nbsps.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This driver supports Freescale NFC (NAND flash controller) found on
Vybrid (VF610), MPC5125, MCF54418 and Kinetis K70. The driver has
been tested using 8-bit and 16-bit NAND interface on the ARM based
Vybrid SoC VF500 and VF610 platform.
parameter page reading.
Limitations:
- Untested on MPC5125 and M54418.
- DMA and pipelining not used.
- 2K pages or less.
- No chip select, one NAND chip per controller.
- No hardware ECC.
Some paths have been hand-optimized and evaluated by measurements
made using mtd_speedtest.ko on a 100MB MTD partition.
Colibri VF50
eb write % eb read % page write % page read %
rel/opt 5175 11537 4560 11039
opt 5164 -0.21 11420 -1.01 4737 +3.88 10918 -1.10
none 5113 -1.20 11352 -1.60 4490 -1.54 10865 -1.58
Colibri VF61
eb write % eb read % page write % page read %
rel/opt 5766 13096 5459 12846
opt 5883 +2.03 13064 -0.24 5561 +1.87 12802 -0.34
none 5701 -1.13 12980 -0.89 5488 +0.53 12735 -0.86
rel = using readl_relaxed/writel_relaxed in optimized paths
opt = hand-optimized by combining multiple accesses into one read/write
The measurements have not been statistically verfied, hence use them
with care. The author came to the conclusion that using the relaxed
variants of readl/writel are not worth the additional code.
Signed-off-by: Bill Pringlemeir <bpringlemeir@nbsps.com>
Tested-by: Albert ARIBAUD <albert.aribaud@3adev.fr>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
After a bit of poking around wondering why my 32-bit user-space can't
seem to send a proper ioctl(BLKPG) to an MTD on my 64-bit kernel
(ARM64), I noticed that struct blkpg_ioctl_arg is actually pretty
unsuitable for use in the ioctl() ABI, due to its use of raw pointers,
and its lack of alignment/packing restrictions (32-bit arch'es tend to
pack the 4 fields into 4 32-bit words, whereas 64-bit arch'es would add
padding after the third int, and make this 6 32-bit words).
Anyway, this means BLKPG deserves some special compat_ioctl handling. Do
the conversion in a small shim for MTD.
block/compat_ioctl.c already has compat support for the block subsystem,
but it does so by a re-marshalling data to/from user-space (see
compat_blkpg_ioctl()). Personally, I think this approach is cleaner.
Tested only on MTD, with an ARM32 user space on an ARM64 kernel.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This patch fixes timeout issues seen on large NOR flash (e.g., 16MB
w25q128fw) when using ioctl(MEMERASE) with offset=0 and length=16M. The
input parameters matter because spi_nor_erase() uses a different code
path for full-chip erase, where we use the SPINOR_OP_CHIP_ERASE (0xc7)
opcode.
Fix: use a different timeout for full-chip erase than for other
commands.
While most operations can be expected to perform relatively similarly
across a variety of NOR flash types and sizes (and therefore might as
well use a similar timeout to keep things simple), full-chip erase is
unique, because the time it typically takes to complete:
(1) is much larger than most operations and
(2) scales with the size of the flash.
Let's base our timeout on the original comments stuck here -- that a 2MB
flash requires max 40s to erase.
Small survey of a few flash datasheets I have lying around:
Chip Size (MB) Max chip erase (seconds)
---- -------- ------------------------
w25q32fw 4 50
w25q64cv 8 30
w25q64fw 8 100
w25q128fw 16 200
s25fl128s 16 ~256
s25fl256s 32 ~512
From this data, it seems plenty sufficient to say we need to wait for
40 seconds for each 2MB of flash.
After this change, it might make some sense to decrease the timeout for
everything else, as even the most extreme operations (single block
erase?) shouldn't take more than a handful of seconds. But for safety,
let's leave it as-is. It's only an error case, after all, so we don't
exactly need to optimize it.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
It is a 512KiB flash with 4 KiB erase sectors.
Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The module pcmciamtd doesn't generate a mtd node for PRETEC 4MB SRAM
cards without the id and hash added to pcmciamtd.c
Tested on 3 different 4MB pretec sram cards.
Signed-off-by: Tom Englund <tomenglund26@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Read Denali hardware revision number and use it to
calculate max_banks, The encoding of max_banks changed
in Denali revision 5.1.
Signed-off-by: Graham Moore <grmoore@opensource.altera.com>
[Brian: parentheses around macro arg]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
A read id operation followed by 0x00 reads the device ID while
a read id operation followed by 0x20 reads the possible ONFI identifier.
As the READID function did not propagate the second id parameter but had
a hard-coded call for 0x90 0x00, reading the ONFI identifier was not
possible and thus chips werde not detected (tested with
MT29F8G08ABABAWP)
Signed-off-by: Enrico Jorns <ejo@pengutronix.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
c->oobbuf hasn't been kmalloced in jffs2_dataflash_setup, so
there is no need to free it.
Signed-off-by: Wei Fang <fangwei1@huawei.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This driver uses some custom macros for printing. Let's use the standard
pr_fmt()/pr_{err,warn}().
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
I'm not sure why we have a PAGE_SIZE restriction on this partition
parser.
If we really wanted the restriction, I would expect it to be a
restriction for *all* parsers, so we'd move it to the MTD core
At any rate, while small partitions may not be useful (they'll often be
smaller than the eraseblock size and therefore can only be used
read-only), they still have use as a read-only partition.
This restriction is especially annoying because it aborts the entire
MTD's cmdline parsing, leaving it unpartitioned.
So, let's kill the restriction and only check for zero-sized partitions,
which I expect we don't want to allow.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
s25fl016k can be found on Embedded Artists' LPC4357 Developer's Kit
where is used in quad mode by the LPC4357 SPIFI controller.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
After the conversion of pxa architecture to common clock framework, the
NAND clock can be disabled on driver exit.
In this case, it happens that if the driver used the NAND and set the
DFI arbitration bit, the next access to a static memory controller area,
such as an ethernet card, will stall the system bus, and the core will
be stalled forever.
This is especially true on pxa31x SoCs, where the NDCR was augmented
with a new bit to prevent this lockups by giving full ownership of the
DFI arbiter to the SMC, in change SCr#6.
Fix this by clearing the DFI arbritration bit in driver exit. This
effectively prevents a lockup on zylonite when removing pxa3xx-nand
module, and using ethernet afterwards.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
In drivers/mtd/mtd_blkdevs.c:
406 set_capacity(gd, (new->size * tr->blksize) >> 9);
The type of new->size is unsigned long and the type of tr->blksize is int,
the result of 'new->size * tr->blksize' may exceed ULONG_MAX on 32bit
machines.
I use nand chip MT29F32G08CBADBWP which is 4GB and the parameters passed
to kernel is 'mtdparts=gpmi-nand:-(user)', the whole nand chip will be
treated as a 4GB mtd partition. new->size is 0x800000 and tr->blksize is
0x200, 'new->size * tr->blksize' however is 0. This is what we do not want
to see.
Using type cast u64 to fix the multiplication overflow issue.
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
As new_valid_dev always returns 1, so !new_valid_dev check is not
needed, remove it.
Signed-off-by: Yaowei Bai <bywxiaobai@163.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Now pxa architecture has a dmaengine driver, remove the access to direct
dma registers in favor of the more generic dmaengine code.
This should be also applicable for mmp and orion, provided they work in
device-tree environment.
This patch also removes the previous hack which was necessary to make
the driver work in a devicetree environment.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Tested-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
[Brian: fixup use of 'enum dma_transfer_direction']
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The sunxi_nand_chips_cleanup() function is missing a call to list_del()
which generates a double free error.
Reported-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: <stable@vger.kernel.org> # 3.19+
Fixes: 1fef62c142 ("mtd: nand: add sunxi NAND flash controller support")
Tested-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Remove unneeded NULL test.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@ expression x; @@
-if (x != NULL)
\(kmem_cache_destroy\|mempool_destroy\|dma_pool_destroy\)(x);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Remove unneeded NULL test.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@ expression x; @@
-if (x != NULL)
\(kmem_cache_destroy\|mempool_destroy\|dma_pool_destroy\)(x);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
struct spi_nor_xfer_cfg and read_xfer/write_xfer hooks were never used by
any driver. Do some cleanup by removing them.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
