This patch enhances s5p-tv with support for DMABUF exporting via
VIDIOC_EXPBUF ioctl.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch enhances s5p-fimc with support for DMABUF exporting via
VIDIOC_EXPBUF ioctl.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Most operations on DMA and DMABUF framework require the size of a buffer to be
page aligned. This patch guarantees the requirement is satisfied for all
vb2-dma-contig buffers.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The DMA transfer must be aligned to a specific value. If userptr is not aligned
to DMA requirements then unexpected corruptions of the memory may occur before
or after a buffer. To prevent such situations, all unligned userptr buffers
are rejected at VIDIOC_QBUF.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds taking reference to the device for MMAP buffers.
Such buffers, may be exported using DMABUF mechanism. If the driver that
created a queue is unloaded then the queue is released, the device might be
released too. However, buffers cannot be released if they are referenced by
DMABUF descriptor(s). The device pointer kept in a buffer must be valid for the
whole buffer's lifetime. Therefore MMAP buffers should take a reference to the
device to avoid risk of dangling pointers.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds support for exporting a dma-contig buffer using
DMABUF interface.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds extension to videobuf2-core. It allow to export an mmap buffer
as a DMABUF file descriptor.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds extension to V4L2 api. A new ioctl VIDIOC_EXPBUF is added. The
ioctl is used to export an mmap buffer as a DMABUF file descriptor.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Let mmap method to use dma_mmap_coherent call. Moreover, this patch removes
vb2_mmap_pfn_range from videobuf2 helpers as it was suggested by Laurent
Pinchart. The function is no longer used in vb2 code.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch enhances s5p-fimc with support for DMABUF importing via
V4L2_MEMORY_DMABUF memory type.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch enhances s5p-tv with support for DMABUF importing via
V4L2_MEMORY_DMABUF memory type.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch enhances mem2mem_testdev device with support for DMABUF importing
via V4L2_MEMORY_DMABUF memory type.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch enhances UVC with support for DMABUF importing via
V4L2_MEMORY_DMABUF memory type.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Tested-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch enhances VIVI driver with a support for importing a buffer
from DMABUF file descriptors.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds support for importing DMABUF files for
vmalloc allocator in Videobuf2.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch makes changes for adding dma-contig as a dma_buf user. It provides
function implementations for the {attach, detach, map, unmap}_dmabuf()
mem_ops of DMABUF memory type.
[author of the original patch]
[integration with refactored dma-contig allocator]
Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds support for prepare/finish callbacks in VB2 allocators. These
callback are used for buffer flushing.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch introduces usage of dma_map_sg to map memory behind
a userspace pointer to a device as dma-contiguous mapping.
This patch contains some of the code kindly provided by Marek Szyprowski
<m.szyprowski@samsung.com> and Kamil Debski <k.debski@samsung.com> and Andrzej
Pietrasiewicz <andrzej.p@samsung.com>. Kind thanks for bug reports from Laurent
Pinchart <laurent.pinchart@ideasonboard.com> and Seung-Woo Kim
<sw0312.kim@samsung.com>.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch removes a reference to alloc_ctx from an instance of a DMA
contiguous buffer. It helps to avoid a risk of a dangling pointer if the
context is released while the buffer is still valid. Moreover it removes one
dereference step while accessing a device structure.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adding DMABUF memory type causes videobuf to complain about not using it
in some switch cases. This patch removes these warnings.
Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds support for DMABUF memory type in videobuf2. It calls relevant
APIs of dma_buf for v4l reqbuf / qbuf / dqbuf operations.
For this version, the support is for videobuf2 as a user of the shared buffer;
so the allocation of the buffer is done outside of V4L2. [A sample allocator of
dma-buf shared buffer is given at [1]]
[1]: Rob Clark's DRM:
https://github.com/robclark/kernel-omap4/commits/drmplane-dmabuf
[original work in the PoC for buffer sharing]
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adds DMABUF memory type to v4l framework. Also adds the related file
descriptor in v4l2_plane and v4l2_buffer.
[original work in the PoC for buffer sharing]
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As reported by Stephen:
After merging the v4l-dvb tree, today's linux-next build (x86_64
allmodconfig) failed like this:
ERROR: "sms_ir_exit" [drivers/media/common/siano/smsmdtv.ko] undefined!
ERROR: "sms_ir_event" [drivers/media/common/siano/smsmdtv.ko] undefined!
ERROR: "sms_ir_init" [drivers/media/common/siano/smsmdtv.ko] undefined!
The smsir file should be part of the smsmdtv core, if RC is defined.
Fix it.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This reverts commit 6ee28d94c9.
The patch got some alien code there, not sure why. Revert it to apply
it properly.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since b9bf2eafaa, the function
ds3000_firmware_ondemand() is called only once during init. This
locking scheme may have been useful when the firmware was loaded at
each tune.
Furthermore, it looks like this 'lock' was put in to prevent concurrent
access (and not recursion as the comments suggest). However, this open-
coded mechanism is anything but race-free and should have used a proper
mutex.
Signed-off-by: Rémi Cardona <remi.cardona@smartjog.com>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Replace kmemdup for kstrdup and cleanup related code.
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The function cx25821_sram_channel_setup_upstream_audio always return zero,
so the return value is not saved any more.
Convert a nonnegative error return code to a negative one, as returned
elsewhere in the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert a nonnegative error return code to a negative one, as returned
elsewhere in the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
While here, replace strlen()+kmemdup() to kstrdup().
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Reviewed-by: walter harms <wharms@bfs.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert a nonnegative error return code to a negative one, as returned
elsewhere in the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert a nonnegative error return code to a negative one, as returned
elsewhere in the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert a nonnegative error return code to a negative one, as returned
elsewhere in the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert a nonnegative error return code to a negative one, as returned
elsewhere in the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert a nonnegative error return code to a negative one, as returned
elsewhere in the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert a nonnegative error return code to a negative one, as returned
elsewhere in the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert a nonnegative error return code to a negative one, as returned
elsewhere in the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The dma_queue list is accessed by both the interrupt handler and by normal
code. It needs to be protected by a lock to prevent possible list corruption.
Corruption has been observed in 'real-life' conditions. Adding this lock made
it go away.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The dma_queue list is accessed by both the interrupt handler and by normal
code. It needs to be protected by a lock to prevent possible list corruption.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In case of error, the function vb2_dma_contig_init_ctx() returns
ERR_PTR() and never returns NULL. The NULL test in the return value
check should be replaced with IS_ERR().
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Lad, Prabhakar <prabhakar.lad@ti.com>
[prabhakar.lad@ti.com: reword commit header]
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The v4l2_subdev_call() call returns -ENODEV when subdev is
null and -ENOIOCTLCMD wnen no icotl is present.
This patch fixes the return type check for v4l2_subdev_call().
The pattern E == C1 && E == C2 is always false. This patch
fix this according to the assumption that && should be ||.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
[prabhakar.lad@ti.com: reword commit messaage]
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The v4l2_subdev_call() call returns -ENODEV when subdev is
null and -ENOIOCTLCMD wnen no icotl is present.
This patch fixes the return type check for v4l2_subdev_call().
The pattern E == C1 && E == C2 is always false. This patch
fix this according to the assumption that && should be ||.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
[prabhakar.lad@ti.com: reword commit message]
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
v4l2_subdev_link_validate_get_format() retrieves the remote pad format
depending on the entity type and prints a warning if the entity type is
not supported. The type check doesn't take the subtype into account, and
thus always prints a warning for device node types, even when supported.
Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
added usb-id as driver supports the stick
Signed-off-by: Andrew Karpow <andy@mailbox.tu-berlin.de>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add new USB ID as driver supports it.
Reported-by: Hubert Lin <hubertwslin@gmail.com>
Tested-by: Hubert Lin <hubertwslin@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Set "y_skip_top" to zero and revise comment as I do not see this line
corruption on two different mt9v022 setups. The first read-out line
is perfectly fine. Add mt9v022 platform data configuring y_skip_top
for platforms that have issues with the first read-out line. Set
y_skip_top to 1 for pcm990 board.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some camera systems cannot operate mt9v022 in normal mode and use
only the snapshot mode. The TechNote for mt9v022 (TN0960) and mt9v024
(TN-09-225) describes required register settings when configuring the
snapshot operation. The snapshot mode requires that certain automatic
functions of the image sensor should be disabled or set to fixed values.
According to the TechNote bit 2 and bit 9 in the register 0x20 must be
set in snapshot mode and unset for normal operation. This applies for
mt9v022 Rev.3 and mt9v024. Add required reg. 0x20 settings dependent on
sensor chip version.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add controls for horizontal and vertical blanking. Also add an error
message for case that the control handler init failed. Since setting
the blanking registers is done by controls now, we shouldn't change
these registers outside of the control function. Use v4l2_ctrl_s_ctrl()
to set them.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is the result of experimenting with the SpeedLink VAD Laplace webcam.
The register sequence for V4L2_MBUS_FMT_YUYV8_2X8 has been identified by
analyzing USB-logs of this device running on MS Windows.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Try reading on video device. If the camera bus driver supports reading
we can try it and return the result. Also add a debug line.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The mx1_camera driver has been broken for a few release cycles since
commit 6bd0812 (dmaengine: imx-dma: merge old dma-v1.c with imx-dma.c).
It seems there is no one even compile tested it since then, as doing
so will end up with the following error.
CC drivers/media/platform/soc_camera/mx1_camera.o
In file included from drivers/media/platform/soc_camera/mx1_camera.c:44:0:
arch/arm/mach-imx/include/mach/dma-mx1-mx2.h:8:25: fatal error: mach/dma-v1.h: No such file or directory
It seems there is no one being interested in bringing it back to
work [1] so far. Let's mark it BROKEN.
[1] https://lkml.org/lkml/2012/2/9/171
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since the MT9V022_TOTAL_SHUTTER_WIDTH register is controlled in manual
mode by V4L2_CID_EXPOSURE control, it shouldn't be written directly in
mt9v022_s_crop(). In manual mode this register should be set to the
V4L2_CID_EXPOSURE control value. Changing this register directly and
outside of the actual control function means that the register value
is not in sync with the corresponding control value. Thus, the following
problem is observed:
- setting this control initially succeeds
- VIDIOC_S_CROP ioctl() overwrites the MT9V022_TOTAL_SHUTTER_WIDTH
register
- setting this control to the same value again doesn't
result in setting the register since the control value
was previously cached and doesn't differ
Remove MT9V022_TOTAL_SHUTTER_WIDTH register setting in mt9v022_s_crop()
and add a comment explaining why it is not needed in manual mode.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add the missing unlock on the error handle path in function
mx2_start_streaming().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A recent commit "[media] v4l2: make vidioc_s_crop const" introduced
warnings in omap1_camera. Fix them by adjusting a function declaration.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
.set_crop() implementation in mx1_camera is identical with the default.
Remove the copy to switch to using the default stab.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A recent commit "[media] v4l2: make vidioc_s_crop const" introduced
warnings in mx2_camera. Fix them by cleanly separating writable and
read-only variables in cropping operations.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A recent commit "[media] v4l2: make vidioc_s_crop const" introduced
warnings in mx3_camera. Fix them by cleanly separating writable and
read-only variables in cropping operations.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A recent commit "[media] v4l2: make vidioc_s_crop const" introduced
warnings in pxa_camera.c. Fix them by adjusting a function declaration.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A recent commit "[media] v4l2: make vidioc_s_crop const" introduced
warnings in sh_mobile_ceu_camera. Fix them by cleanly separating writable
and read-only variables in cropping operations.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A recent commit "[media] v4l2: make vidioc_s_crop const" introduced
warnings in sh_vou. Fix them by cleanly separating writable and
read-only variables in cropping operations.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The STDI block may measure wrong values, especially for lcvs and lcf. If the
driver can not find any valid timing, the STDI block is restarted to measure
the video timings again. The function will return an error, but the restart of
STDI will generate a new STDI interrupt and the format detection process will
restart.
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use predefined video timings (prim_mode/vid_std) when available as recommended
by Analog Devices (http://ez.analog.com/message/48267#48267).
Also remove 720p30 support since the ADV7604 can't handle that.
(http://ez.analog.com/message/61488#61488)
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This should have break statements in it.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert the struct i2c_msg initialization to C99 format. This makes
maintaining and editing the code simpler. Also helps once other fields
like transferred are added in future.
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Changes the way the primary mode is handled:
- Remove it from platform_data since it doesn't belong there.
- Add a new mode enum for use with s_routing.
- Collapse the two HDMI modes into one HDMI mode: when setting up the
timings manually we do not need to select HDMI_COMP mode. That's only
needed when selecting a preset.
This patch prepares for the next step where we switch to using the presets
where available.
Signed-off-by: Mats Randgaard <mats.randgaard@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The winbond hardware has a counter for leading edges, which increases as
they are received. As we read raw IR from a fifo in an interrupt handler,
we cannot correlate them to specific IR pulses so we simply count all
pulses and edges until we go idle and disable the receiver.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The receiver is never disabled by idle mode since rxstate never gets set
to RXSTATE_ACTIVE, so we keep on getting interrupts after the first IR
activity ends. Note that ir_raw_event_reset() already calls
ir_raw_event_handle().
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The sparse warning is:
"drivers/media/usb/stkwebcam/stk-webcam.c:59:5:
warning: symbol 'first_init' was not declared. Should it be static?"
Declare variable 'first_init' as static and local to the function.
Found by Hans Verkuil's daily build. Tested by compilation only.
Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As a first step towards migrating davinci platforms to use common clock
framework, replace all instances of clk_enable() with clk_prepare_enable()
and clk_disable() with clk_disable_unprepare().
Also fixes some issues related to clk clean up in the driver
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Tested-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
set device_caps and also change the driver and
bus_info to proper values as per standard.
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Warnings were generated because of the following commit changed data type for
address pointer
195bbca ARM: 7500/1: io: avoid writeback addressing modes for __raw_ accessors
add __iomem annotation to fix following warnings
drivers/media/platform/davinci/vpbe_osd.c: In function ‘osd_read’:
drivers/media/platform/davinci/vpbe_osd.c:49:2: warning: passing
argument 1 of ‘__raw_readl’ makes pointer from integer without a cast [enabled by default]
arch/arm/include/asm/io.h:104:19: note: expected ‘const volatile
void *’ but argument is of type ‘long unsigned int’
This patch stores the ioremap_nocache() returned address in a
void __iomem * instead of a unsigned long and passes the same to
readl/writel functions which fixes the above warnings.
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Update contact information to correspond my e-mail address changes.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently used registers 0xc5 and 0xc7 provide only a very coarse
adjustment possibility within a very small value range (0-3).
With registers 0x01 and 0x03, a fine grained adjustment with
255 steps is possible. This is also what the Windows driver does.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
R,G,B balance registers are 0x01-0x03 instead of 0x02-0x04,
which lead to the wrong conclusion that values are inverted.
Exposure is controlled via page 3 registers and this is already documented.
Also fix a whitespace issue.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Many people are trying to use stk1160 on low memory devices.
Instead of failing if one allocation fails, we allow the driver
to continue working if fewer transfer buffers are available.
Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Move iommu/iovmm headers from plat/ to platform_data/ as part of the
single zImage work.
Partially based on an earlier version by Ido Yariv <ido@wizery.com>.
Cc: Ido Yariv <ido@wizery.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Omar Ramirez Luna <omar.luna@linaro.org>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Ohad Ben-Cohen <ohad@wizery.com>
Acked-by: Joerg Roedel <joro@8bytes.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Looks like the iommu framework does not have generic functions
exported for all the needs yet. The hardware specific functions
are defined in files like intel-iommu.h and amd-iommu.h. Follow
the same standard for omap-iommu.h.
This is needed because we are removing plat and mach includes
for ARM common zImage support. Further work should continue
in the iommu framework context as only pure platform data will
be communicated from arch/arm/*omap*/* code to the iommu
framework.
Cc: Ido Yariv <ido@wizery.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Omar Ramirez Luna <omar.luna@linaro.org>
Cc: linux-media@vger.kernel.org
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Ohad Ben-Cohen <ohad@wizery.com>
Acked-by: Joerg Roedel <joro@8bytes.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Since mx27 transitioned to the commmon clock framework in 3.5, the correct way
to acquire the csi clock is to get csi_ahb and csi_per clocks separately.
By not doing so the camera sensor does not probe correctly:
soc-camera-pdrv soc-camera-pdrv.0: Probing soc-camera-pdrv.0
mx2-camera mx2-camera.0: Camera driver attached to camera 0
ov2640 0-0030: Product ID error fb:fb
mx2-camera mx2-camera.0: Camera driver detached from camera 0
mx2-camera mx2-camera.0: MX2 Camera (CSI) driver probed, clock frequency: 66500000
Adapt the mx2_camera driver to the new clock framework and make it functional
again.
Tested-by: Gaëtan Carlier <gcembed@gmail.com>
Tested-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Usage of TSTAMP_* macros has gone in 2010 in 730947bc (V4L/DVB: vivi:
clean up and a major overhaul) but the macros remain. Say goodbye to
them.
Signed-off-by: Kirill Smelkov <kirr@mns.spb.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As reported by Stephen:
After merging the v4l-dvb tree, today's linux-next build (x86_64
allmodconfig) failed like this:
ERROR: "sms_ir_exit" [drivers/media/common/siano/smsmdtv.ko] undefined!
ERROR: "sms_ir_event" [drivers/media/common/siano/smsmdtv.ko] undefined!
ERROR: "sms_ir_init" [drivers/media/common/siano/smsmdtv.ko] undefined!
The smsir file should be part of the smsmdtv core, if RC is defined.
Fix it.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fixes error: dvb_usb_v2: pid_filter() failed=-4
error code -4 is EINTR, Interrupted system call
That error blocks I/O in some cases as -EINTR error was returned
by the mutex which was protecting USB control messages. We want
configure hardware to sleep mode on every case after tuning is
stopped. That kind of behavior blocks it, leaving hardware some
unwanted state in worst case.
That error was seen every time when af9015 was plugged to USB1.1
which leads use of hardware PID filters. Stop tuning (tzap) with
ctrl+c failed as driver tries to remove hardware PID filters.
Tested with every hardware which uses routine in question.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Code block braces were missing which leds broken error logging and compiler warning.
drivers/media/usb/dvb-usb-v2/dvb_usb_core.c: In function 'dvb_usb_ctrl_feed':
drivers/media/usb/dvb-usb-v2/dvb_usb_core.c:291:12: warning: 'ret' may be used uninitialized in this function [-Wuninitialized]
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reported-by: Milan Tuma <milan.olin@seznam.cz>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As reported by Antti and by Stephen:
drivers/built-in.o: In function `sms_ir_event':
/home/david/checkouts/linux/drivers/media/common/siano/smsir.c:48: undefined reference to `ir_raw_event_store'
/home/david/checkouts/linux/drivers/media/common/siano/smsir.c:50: undefined reference to `ir_raw_event_handle'
drivers/built-in.o: In function `sms_ir_init':
/home/david/checkouts/linux/drivers/media/common/siano/smsir.c:56: undefined reference to `smscore_get_board_id'
/home/david/checkouts/linux/drivers/media/common/siano/smsir.c:60: undefined reference to `rc_allocate_device'
/home/david/checkouts/linux/drivers/media/common/siano/smsir.c:72: undefined reference to `sms_get_board'
/home/david/checkouts/linux/drivers/media/common/siano/smsir.c:92: undefined reference to `sms_get_board'
/home/david/checkouts/linux/drivers/media/common/siano/smsir.c:97: undefined reference to `rc_register_device'
/home/david/checkouts/linux/drivers/media/common/siano/smsir.c💯 undefined reference to `rc_free_device'
drivers/built-in.o: In function `sms_ir_exit':
/home/david/checkouts/linux/drivers/media/common/siano/smsir.c:111: undefined reference to `rc_unregister_device'
make: *** [vmlinux] Error 1
Caused by commit fdd1eeb49d "[media] siano: allow compiling it without RC support"
And it happens when CONFIG_SMS_SIANO_RC=y and CONFIG_RC_CORE=m .
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reported-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
From Michal Simek:
* 'arm-next' of git://git.xilinx.com/linux-xlnx:
zynq: move static peripheral mappings
zynq: remove use of CLKDEV_LOOKUP
zynq: use pl310 device tree bindings
zynq: use GIC device tree bindings
+ Linux 3.7-rc3
This code should be private to mach-omap2.
The only use for it in for omap1 has been in dmtimer.c
to check for context loss. However, omap1 does not
lose context during idle, so the code is not needed.
Further, omap1 timer has OMAP_TIMER_ALWON set, so omap1
was not hitting omap_pm_get_dev_context_loss_count()
test.
Cc: Jon Hunter <jon-hunter@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The limits are input parameters and should not be modified by the
smiapp_pll_calculate() function. Make them const.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
OP and VT limits have identical fields, create a shared structure for
both.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Support sensors with parallel interface.
Make smiapp_pll.flags also 8-bit so it fits nicely into two 32-bit words
with the other 8-bit fields.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The input values for PLL configuration are mostly static. So set them when
the sensor is registered.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
