This patch adds clocks necessary for SD card controller on apq8064 SOC.
Without this patch the clocks are not visible to the sdcc driver.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Use a sequence for enabling hardware control of the SATA PLL
that works both when using the SATA lane with SATA and when
using it with XUSB.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
sun6i-a31-apb0-gates supports using clock-indices for holes between
individual gates. However, the driver passes the number of gates
registered in clk_data->clk_num, which of_clk_src_onecell_get uses
to recognize the range of valid indices a consumer can use.
This patch makes the driver pass the maximum gate index + 1, so
of_clk_src_onecell_get does not complain about indices greater
than gates registered.
This was tested on the A23 SoC, which has a similar APB0 clock,
but has holes for gates to removed IP blocks.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A23 has an almost identical PRCM clock tree. The difference in
the APB0 clock is the smallest divisor is 1, instead of 2.
This patch adds a separate sun8i-a23-apb0-clk driver to support it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The clock control unit on the A23 is similar to the one found on the A31.
The AHB1, APB1, APB2 gates on the A23 are almost identical to the ones
on the A31, but some outputs are missing.
The main CPU PLL (PLL1) however is like that on older Allwinner SoCs,
such as the A10 or A20, but the N factor starts from 1 instead of 0.
This patch adds support for PLL1 and all the basic clock muxes and gates.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
A few of the clock modules have odd dividers, such as
the 2 lowest dividers being the same (2), or have the
same divider when the highest bit is set.
This patch adds support for optional divider tables,
so the clock framework will know about the odd values.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The PLLs on newer Allwinner SoC's, such as the A31 and A23, have a
N multiplier factor that starts from 1, not 0.
This patch adds an option to the factor clk driver's config data
structures to specify the base value of N.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
With sunxi_gates clocks registered with clkdev, we can use the
protected clocks list to enable the "ahb_sdram" clock, instead
of looking for it and adding CLK_IGNORE_UNUSED inline in the
clock setup code.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The new important clock protect code requires the clocks be
registered with clkdev. This was missing for sunxi_gates
type clocks.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The HDMI PLL input to the tv mux is supposed to be 3, not 2. Fix
the code so that we can properly select the HDMI PLL.
Fixes: 6d00b56fe "clk: qcom: Add support for MSM8960's multimedia clock controller (MMCC)"
Reported-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Define and export a new function clk_debugs_add_file which adds a file
to a existing clock's debugfs directory. This can be used by clock
providers to add debugfs entries which are not related to a specific clock
type. Examples include the ability to measure the rate of a clock. It can
also be used by modules to create new debugfs entries. This is useful if you
want to expose features for testing which can potentially cause system
instability such as allowing to change a clock's rate from userspace.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This pull request contains fixes for various issues found while testing
-rc versions of Linux 3.16. Mostly two kinds of patches:
* Fixes of incorrectly defined clocks
1) a37c82a clk: samsung: exynos4: Remove SRC_MASK_ISP gates
Issue present since v3.10.
2) 0b1643b clk/exynos5250: fix bit number for tv sysmmu clock
Issue present since v3.16.
3) 44ff025 clk: exynos5420: Remove aclk66_peric from the clock tree description
Issue present since v3.11.
* Adding things missed by original patches
1) cec1cde clk: samsung: fix several typos to fix boot on s3c2410
2) 34ece9e clk: samsung: add more aliases for s3c24xx
Both issues present since the driver was added in v3.16.
3) a92dda4 clk: s3c64xx: Hookup SPI clocks correctly
Issue present since v3.12.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=eE4V
-----END PGP SIGNATURE-----
Merge tag 'for_3.16/samsung-clk-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tfiga/samsung-clk into clk-fixes-samsung
Samsung clock fixes for v3.16.
This pull request contains fixes for various issues found while testing
-rc versions of Linux 3.16. Mostly two kinds of patches:
* Fixes of incorrectly defined clocks
1) a37c82a clk: samsung: exynos4: Remove SRC_MASK_ISP gates
Issue present since v3.10.
2) 0b1643b clk/exynos5250: fix bit number for tv sysmmu clock
Issue present since v3.16.
3) 44ff025 clk: exynos5420: Remove aclk66_peric from the clock tree description
Issue present since v3.11.
* Adding things missed by original patches
1) cec1cde clk: samsung: fix several typos to fix boot on s3c2410
2) 34ece9e clk: samsung: add more aliases for s3c24xx
Both issues present since the driver was added in v3.16.
3) a92dda4 clk: s3c64xx: Hookup SPI clocks correctly
Issue present since v3.12.
s2mps11 clocks had registered callbacks for prepare ,unprepare and is_enabled.
During disabling unused clocks the lack of is_prepared caused that unused
s2mps11 clocks were not unprepared and stayed active.
Regmap_read is cached so it can be called in is_prepare callback
to achieve this information. Enabled field was removed from struct s2mps11_clk.
Signed-off-by: Karol Wrona <k.wrona@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
When the main crystal frequency is not set, the main clock is approximated using
the MAINF value in the CKGR_MCFR register. Warn the user in that case.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris BREZILLON <boris.brezillon@overkiz.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
USB_DPLL must be initialized and locked at boot so that
USB modules can work.
Also program USB_DLL_M2 output to half rate.
CC: Mike Turquette <mturquette@linaro.org>
CC: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
devm_ioremap_resource returns an ERR_PTR value, not NULL, on failure.
A simplified version of the semantic match that finds this problem is as
follows:
// <smpl>
@@
expression e,e1;
statement S;
@@
*e = devm_ioremap_resource(...);
if (!e1) S
// </smpl>
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Acked-by Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Palmas class of devices can provide 32K clock(s) to be used by other devices
on the board. Depending on the actual device the provided clocks can be:
CLK32K_KG and CLK32K_KGAUDIO
or only one:
CLK32K_KG (TPS659039 for example)
Use separate compatible flags for the two 32K clock.
A system which needs or have only one of the 32k clock from
Palmas will need to add node(s) for each clock as separate section
in the dts file.
The two compatible property is:
"ti,palmas-clk32kg" for clk32kg clock
"ti,palmas-clk32kgaudio" for clk32kgaudio clock
Apart from the register control of the clocks - which is done via
the clock API there is a posibility to enable the external sleep
control. In this way the clock can be enabled/disabled on demand by the
user of the clock.
See the documentation for more details.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Palmas class of devices can provide 32K clock(s) to be used by other devices
on the board. Depending on the actual device the provided clocks can be:
CLK32K_KG and CLK32K_KGAUDIO
or only one:
CLK32K_KG (TPS659039 for example)
Use separate compatible flags for the two 32K clock.
A system which needs or have only one of the 32k clock from
Palmas will need to add node(s) for each clock as separate section
in the dts file.
The two compatible property is:
"ti,palmas-clk32kg" for clk32kg clock
"ti,palmas-clk32kgaudio" for clk32kgaudio clock
Apart from the register control of the clocks - which is done via
the clock API there is a posibility to enable the external sleep
control. In this way the clock can be enabled/disabled on demand by the
user of the clock.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
‘all_lists’ and ‘orphan_list’ is accessed only when DEBUG_FS is defined.
Thus, make their compilation conditional to fix the below warnings introduced
by commit 27b8d5f723 ("clk: flatten clk tree in debugfs"):
drivers/clk/clk.c:40:27: warning: ‘all_lists’ defined but not used [-Wunused-variable]
drivers/clk/clk.c:46:27: warning: ‘orphan_list’ defined but not used [-Wunused-variable]
Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
Cc: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
WARNING: drivers/built-in.o(.data+0x10258):
Section mismatch in reference from the variable ppc_corenet_clk_driver
to the (unknown reference) .init.rodata:(unknown)
The variable ppc_corenet_clk_driver references
the (unknown reference) __initconst (unknown)
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console
Signed-off-by: Jingchang Lu <jingchang.lu@freescale.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
When writing a module for testing or debugging purposes, there is no way to
get hold of clk handles. This patch solves this by exposing all valid clocks
as clkdev's for the virtual device tegra-clk-debug.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
The "aclk66_peric" clock is a gate clock with a whole bunch of gates
underneath it. This big gate isn't very useful to include in our
clock tree. If any of the children need to be turned on then the big
gate will need to be on anyway. ...and there are plenty of other "big
gates" that aren't described in our clock tree, some of which shut off
collections of clocks that have no relationship in the hierarchy so
are hard to model.
"aclk66_peric" is causing earlyprintk problems since it gets disabled
as part of the boot process, so let's just remove it.
Strangely (and for no good reason) this clock is exported as part of
the common clock bindings. Remove it since there are no in-kernel
device trees using it and no reason anyone out of tree should refer to
it either.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Change bit from 2 to 9 for tv (mixer) sysmmu clock.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Reviewed-by: Sachin Kamat <sachin.kamat@samsung.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
In the move to this clock driver the hookups for the SPI clocks were
dropped, which causes my system Cragganmore (s3c6410 based) to be unable
to locate any spibus clocks. This patch adds them back in.
When taking the clock from the epll clock (SCLK) the rates on the SPI
bus are incorrect, this needs further debugging but the hookup here
should be correct and the problem should be else where.
The USBCLK case has been dropped because this requires the USB PHY to be
enabled.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
ISP special clocks have dedicated gating registers and so MUX SRC_MASK
register should not be used. This patch fixes the problem of
Exynos4x12-based boards freezing on system suspend, because those
mux outputs need not to be masked while suspending.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Cc: Mike Turquette <mturquette@linaro.org>
There's a several typos in a driver: 2410 instead of S3C2410
and wrong argument to ARRAY_SIZE(). They prevent s3c2410
from properly booting.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Pull ARM fixes from Russell King:
"Another round of ARM fixes. The largest change here is the L2 changes
to work around problems for the Armada 37x/380 devices, where most of
the size comes down to comments rather than code.
The other significant fix here is for the ptrace code, to ensure that
rewritten syscalls work as intended. This was pointed out by Kees
Cook, but Will Deacon reworked the patch to be more elegant.
The remainder are fairly trivial changes"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 8087/1: ptrace: reload syscall number after secure_computing() check
ARM: 8086/1: Set memblock limit for nommu
ARM: 8085/1: sa1100: collie: add top boot mtd partition
ARM: 8084/1: sa1100: collie: revert back to cfi_probe
ARM: 8080/1: mcpm.h: remove unused variable declaration
ARM: 8076/1: mm: add support for HW coherent systems in PL310 cache
Note that I don't maintain Documentation/ABI/,
Documentation/devicetree/, or the language translation files.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
These days most people use git to send patches so I have added a section
about that.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On the syscall tracing path, we call out to secure_computing() to allow
seccomp to check the syscall number being attempted. As part of this, a
SIGTRAP may be sent to the tracer and the syscall could be re-written by
a subsequent SET_SYSCALL ptrace request. Unfortunately, this new syscall
is ignored by the current code unless TIF_SYSCALL_TRACE is also set on
the current thread.
This patch slightly reworks the enter path of the syscall tracing code
so that we always reload the syscall number from
current_thread_info()->syscall after the potential ptrace traps.
Acked-by: Kees Cook <keescook@chromium.org>
Tested-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit 1c2f87c (ARM: 8025/1: Get rid of meminfo) changed find_limits
to use memblock_get_current_limit for calculating the max_low pfn.
nommu targets never actually set a limit on memblock though which
means memblock_get_current_limit will just return the default
value. Set the memblock_limit to be the end of DDR to make sure
bounds are calculated correctly.
Signed-off-by: Laura Abbott <lauraa@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The CFI mapping is now perfect so we can expose the top block, read only.
There isn't much to read, though, just the sharpsl_params values.
Signed-off-by: Andrea Adami <andrea.adami@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reverts commit d26b17edaf
ARM: sa1100: collie.c: fall back to jedec_probe flash detection
Unfortunately the detection was challenged on the defective unit used for tests:
one of the NOR chips did not respond to the CFI query.
Moreover that bad device needed extra delays on erase-suspend/resume cycles.
Tested personally on 3 different units and with feedback of two other users.
Signed-off-by: Andrea Adami <andrea.adami@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The sync_phys variable has been replaced by link time computation in
mcpm_head.S before the code was submitted upstream.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When a PL310 cache is used on a system that provides hardware
coherency, the outer cache sync operation is useless, and can be
skipped. Moreover, on some systems, it is harmful as it causes
deadlocks between the Marvell coherency mechanism, the Marvell PCIe
controller and the Cortex-A9.
To avoid this, this commit introduces a new Device Tree property
'arm,io-coherent' for the L2 cache controller node, valid only for the
PL310 cache. It identifies the usage of the PL310 cache in an I/O
coherent configuration. Internally, it makes the driver disable the
outer cache sync operation.
Note that technically speaking, a fully coherent system wouldn't
require any of the other .outer_cache operations. However, in
practice, when booting secondary CPUs, these are not yet coherent, and
therefore a set of cache maintenance operations are necessary at this
point. This explains why we keep the other .outer_cache operations and
only ->sync is disabled.
While in theory any write to a PL310 register could cause the
deadlock, in practice, disabling ->sync is sufficient to workaround
the deadlock, since the other cache maintenance operations are only
used in very specific situations.
Contrary to previous versions of this patch, this new version does not
simply NULL-ify the ->sync member, because the l2c_init_data
structures are now 'const' and therefore cannot be modified, which is
a good thing. Therefore, this patch introduces a separate
l2c_init_data instance, called of_l2c310_coherent_data.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
A few driver specific fixes, the biggest one being a fix for the newly
added Qualcomm SPI controller driver to make it not use its internal
chip select due to hardware bugs, replacing it with GPIOs.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Jdak
-----END PGP SIGNATURE-----
Merge tag 'spi-v3.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A few driver specific fixes, the biggest one being a fix for the newly
added Qualcomm SPI controller driver to make it not use its internal
chip select due to hardware bugs, replacing it with GPIOs"
* tag 'spi-v3.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: qup: Remove chip select function
spi: qup: Fix order of spi_register_master
spi: sh-sci: fix use-after-free in sh_sci_spi_remove()
spi/pxa2xx: fix incorrect SW mode chipselect setting for BayTrail LPSS SPI
Several driver specific fixes here, the palmas fixes being especially
important for a range of boards - the recent updates to support new
devices have introduced several regressions.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=K0Hp
-----END PGP SIGNATURE-----
Merge tag 'regulator-v3.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"Several driver specific fixes here, the palmas fixes being especially
important for a range of boards - the recent updates to support new
devices have introduced several regressions"
* tag 'regulator-v3.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: tps65218: Correct the the config register for LDO1
regulator: tps65218: Add the missing of_node assignment in probe
regulator: palmas: fix typo in enable_reg calculation
regulator: bcm590xx: fix vbus name
regulator: palmas: Fix SMPS enable/disable/is_enabled
Pull SCSI target fixes from Nicholas Bellinger:
"Mostly minor fixes this time around. The highlights include:
- iscsi-target CHAP authentication fixes to enforce explicit key
values (Tejas Vaykole + rahul.rane)
- fix a long-standing OOPs in target-core when a alua configfs
attribute is accessed after port symlink has been removed.
(Sebastian Herbszt)
- fix a v3.10.y iscsi-target regression causing the login reject
status class/detail to be ignored (Christoph Vu-Brugier)
- fix a v3.10.y iscsi-target regression to avoid rejecting an
existing ITT during Data-Out when data-direction is wrong (Santosh
Kulkarni + Arshad Hussain)
- fix a iscsi-target related shutdown deadlock on UP kernels (Mikulas
Patocka)
- fix a v3.16-rc1 build issue with vhost-scsi + !CONFIG_NET (MST)"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
iscsi-target: fix iscsit_del_np deadlock on unload
iovec: move memcpy_from/toiovecend to lib/iovec.c
iscsi-target: Avoid rejecting incorrect ITT for Data-Out
tcm_loop: Fix memory leak in tcm_loop_submission_work error path
iscsi-target: Explicily clear login response PDU in exception path
target: Fix left-over se_lun->lun_sep pointer OOPs
iscsi-target; Enforce 1024 byte maximum for CHAP_C key value
iscsi-target: Convert chap_server_compute_md5 to use kstrtoul
