Enable runtime PM for i3c master node during master registration time.
Sometimes i3c client device driver may want to control the PM of the
parent (master) to perform the transactions and save the power in an
efficient way by controlling the session. Hence device can call PM
APIs by passing the parent node.
Here, I3C target device when calls pm_runtime_get_sync(dev->parent)
couldn't invoke master drivers runtime PM callback registered by
the master driver because parent's PM status was disabled in the
Master node.
Also call pm_runtime_no_callbacks() and pm_suspend_ignore_children()
for the master node to not have any callback addition and ignore the
children to have runtime PM work just locally in the driver. This
should be generic and common change for all i3c devices and should
not have any other impact.
With these changes, I3C client device works and able to invoke
master driver registered runtime PM callbacks.
Signed-off-by: Mukesh Kumar Savaliya <quic_msavaliy@quicinc.com>
Link: https://lore.kernel.org/r/20240228093407.4038399-1-quic_msavaliy@quicinc.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Since commit d492cc2573 ("driver core: device.h: make struct
bus_type a const *"), the driver core can properly handle constant
struct bus_type, move the i3c_bus_type variable to be a constant
structure as well, placing it into read-only memory which can not be
modified at runtime.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ricardo B. Marliere <ricardo@marliere.net>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20240213-bus_cleanup-i3c-v1-1-403aea18f05a@marliere.net
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Add hotjoin entry in sys file system allow user enable/disable hotjoin
feature.
Add (*enable(disable)_hotjoin)() to i3c_master_controller_ops.
Add api i3c_master_enable(disable)_hotjoin();
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20231201222532.2431484-2-Frank.Li@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Some I3C hardware will report error when an incorrect length is received from
device. GETMXDS CCC are available in 2 formats: without turnaround time (format
1) and with turnaround time (format 2). There is no mechanics to determine which
format is supported by device. So in case sending GETMXDS CCC format 2 resulted
in a failure, try sending GETMXDS CCC format 1 instead.
Signed-off-by: Joshua Yeong <joshua.yeong@starfivetech.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20231114085525.6271-2-joshua.yeong@starfivetech.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Core:
- handle IBI in the proper order
Drivers:
- cdns: fix status register access
- mipi-i3c-hci: many fixes now that the driver has been actually tested
- svc: many IBI fixes, correct compatible string, fix hot join corner cases
-----BEGIN PGP SIGNATURE-----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=rFcf
-----END PGP SIGNATURE-----
Merge tag 'i3c/for-6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux
Pull i3c updates from Alexandre Belloni:
"There are now more fixes because as stated in my previous pull
request, people now have access to actual hardware.
Core:
- handle IBI in the proper order
Drivers:
- cdns: fix status register access
- mipi-i3c-hci: many fixes now that the driver has been actually
tested
- svc: many IBI fixes, correct compatible string, fix hot join corner
cases"
* tag 'i3c/for-6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux: (29 commits)
i3c: master: handle IBIs in order they came
i3c: master: mipi-i3c-hci: Fix a kernel panic for accessing DAT_data.
i3c: master: svc: fix compatibility string mismatch with binding doc
i3c: master: svc: fix random hot join failure since timeout error
i3c: master: svc: fix SDA keep low when polling IBIWON timeout happen
i3c: master: svc: fix check wrong status register in irq handler
i3c: master: svc: fix ibi may not return mandatory data byte
i3c: master: svc: fix wrong data return when IBI happen during start frame
i3c: master: svc: fix race condition in ibi work thread
i3c: Fix typo "Provisional ID" to "Provisioned ID"
i3c: Fix potential refcount leak in i3c_master_register_new_i3c_devs
i3c: mipi-i3c-hci: Resume controller after aborted transfer
i3c: mipi-i3c-hci: Resume controller explicitly
i3c: mipi-i3c-hci: Fix missing xfer->completion in hci_cmd_v1_daa()
i3c: mipi-i3c-hci: Do not unmap region not mapped for transfer
i3c: mipi-i3c-hci: Set number of SW enabled Ring Bundles earlier
i3c: mipi-i3c-hci: Fix race between bus cleanup and interrupt
i3c: mipi-i3c-hci: Set ring start request together with enable
i3c: mipi-i3c-hci: Remove BUG() when Ring Abort request times out
i3c: mipi-i3c-hci: Fix out of bounds access in hci_dma_irq_handler
...
IBI shall be handled in order they appear on the bus. Otherwise could hit
case when order of handling them in device driver will be different. It may
lead to invalid assembling fragmented packets or events order broken.
Added separate workqueue with option WQ_MEM_RECLAIM for each device driver.
This ensures IBI handling order and improves IBI handling performance: IBI
handlers for device B are not blocked by IBI handlers for device A.
Original solution (single workqueue in main driver) was able to handle also
general IBI (not related to specific device) like HJ or MR. So leaving this
for such purposes.
Signed-off-by: Zbigniew Lukwinski <zbigniew.lukwinski@linux.intel.com>
Link: https://lore.kernel.org/r/20231015222334.1652401-2-zbigniew.lukwinski@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
This allows other drivers to be notified when new i3c busses are
attached, referring to a whole i3c bus as opposed to individual
devices.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: Matt Johnston <matt@codeconstruct.com.au>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
put_device() needs to be called on failure of device_register()
to give up the reference initialized in it to avoid refcount leak.
Fixes: 3a379bbcea ("i3c: Add core I3C infrastructure")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Link: https://lore.kernel.org/r/20230921082410.25548-1-dinghao.liu@zju.edu.cn
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Copy the DMA masks and parameters for an I3C master device from parent
device so that the master device has them set for the DMA buffer and
mapping API.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20230921055704.1087277-2-jarkko.nikula@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
`strncpy` is deprecated for use on NUL-terminated destination strings [1].
We should prefer more robust and less ambiguous string interfaces.
We expect adap->name to be NUL-terminated based on i2c_adapter name use:
| dev_dbg(&adap->dev, "adapter [%s] registered\n", adap->name);
NUL-padding does not seem to be required as `master` is zero-allocated
and `i3c_master_to_i2c_adapter` simply returns a field from within
`master`:
| master = devm_kzalloc(dev, sizeof(*master), GFP_KERNEL);
...
| struct i2c_adapter *adap = i3c_master_to_i2c_adapter(master);
...
| static struct i2c_adapter *
| i3c_master_to_i2c_adapter(struct i3c_master_controller *master)
| {
| return &master->i2c;
| }
This means that `adap->name` should already be filled with NUL-bytes.
Considering the above, a suitable replacement is `strscpy` [2] due to
the fact that it guarantees NUL-termination on the destination buffer
without unnecessarily NUL-padding.
Link: https://www.kernel.org/doc/html/latest/process/deprecated.html#strncpy-on-nul-terminated-strings [1]
Link: https://manpages.debian.org/testing/linux-manual-4.8/strscpy.9.en.html [2]
Link: https://github.com/KSPP/linux/issues/90
Cc: linux-hardening@vger.kernel.org
Signed-off-by: Justin Stitt <justinstitt@google.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20230921-strncpy-drivers-i3c-master-c-v1-1-9fdb8d8169e1@google.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
When a I3C DT node has a static_addr and an init_dyn_addr,the
init_dyn_addr is reserved in i3c_master_bus_init() and then
the static_addr is reserved in i3c_master_early_i3c_dev_add().
But if the dynamic address is same as static then above
procedure would fail.
Add a check to pass i3c_bus_get_addr_slot_status() when static
and dynamic address are equal.
Signed-off-by: Aniket <aniketmaurya@google.com>
Link: https://lore.kernel.org/r/20230822051938.2852567-1-aniketmaurya@google.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Parse the /aliases node to assign any fixed bus numbers, as is done with
the i2c subsystem. Numbering for non-aliased busses will start after the
highest fixed bus number.
This allows an alias node such as:
aliases {
i3c0 = &bus_a,
i3c4 = &bus_b,
};
to set the numbering for a set of i3c controllers:
/* fixed-numbered bus, assigned "i3c-0" */
bus_a: i3c-master {
};
/* another fixed-numbered bus, assigned "i3c-4" */
bus_b: i3c-master {
};
/* dynamic-numbered bus, likely assigned "i3c-5" */
bus_c: i3c-master {
};
If no i3c device aliases are present, the numbering will stay as-is,
starting from 0.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Link: https://lore.kernel.org/r/20230405094149.1513209-1-jk@codeconstruct.com.au
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The function returned zero unconditionally. Switch the return type to void
and simplify the callers accordingly.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20230318233311.265186-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Subsystem:
- transfer pid from boardinfo to device info
Drivers:
- dw-i3c-master: stop hardcoding initial speed
-----BEGIN PGP SIGNATURE-----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=CEs9
-----END PGP SIGNATURE-----
Merge tag 'i3c/for-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux
Pull i3c updates from Alexandre Belloni:
"Subsystem:
- transfer pid from boardinfo to device info
Drivers:
- dw-i3c-master: stop hardcoding initial speed"
* tag 'i3c/for-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux:
i3c: master: dw: stop hardcoding initial speed
i3c: transfer pid from boardinfo to device info
I3C device PID could be defined in device tree and stored in
i3c_dev_boardinfo. It should be passed to i3c_device_info when
allocating a i3c_dev_desc.
Rational behind this change is: when users decide to use SETDASA to
assign a dynamic address with exactly the original static address, in
step of i3c_master_reattach_i3c_dev, this address is checked to be
taken. Then device information retrieving step is skipped. As a result,
though the i3c device is registered correctly, its device driver could
not be probed.
Tested: Tested with a I3C device. If assigned-address is set to be the
device's static address, without this change, its device driver could
not probed. And with this change, its driver is probed successfully.
Signed-off-by: Jack Chen <zenghuchen@google.com>
Link: https://lore.kernel.org/r/20230105212952.56321-1-zenghuchen@google.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The uevent() callback in struct device_type should not be modifying the
device that is passed into it, so mark it as a const * and propagate the
function signature changes out into all relevant subsystems that use
this callback.
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Andreas Noever <andreas.noever@gmail.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Bard Liao <yung-chuan.liao@linux.intel.com>
Cc: Chaitanya Kulkarni <kch@nvidia.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Frank Rowand <frowand.list@gmail.com>
Cc: Ira Weiny <ira.weiny@intel.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Jilin Yuan <yuanjilin@cdjrlc.com>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Mark Gross <markgross@kernel.org>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: "Matthew Wilcox (Oracle)" <willy@infradead.org>
Cc: Maximilian Luz <luzmaximilian@gmail.com>
Cc: Michael Jamet <michael.jamet@intel.com>
Cc: Ming Lei <ming.lei@redhat.com>
Cc: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Sakari Ailus <sakari.ailus@linux.intel.com>
Cc: Sanyog Kale <sanyog.r.kale@intel.com>
Cc: Sean Young <sean@mess.org>
Cc: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Won Chung <wonchung@google.com>
Cc: Yehezkel Bernat <YehezkelShB@gmail.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> # for Thunderbolt
Acked-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Wolfram Sang <wsa@kernel.org>
Acked-by: Vinod Koul <vkoul@kernel.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230111113018.459199-6-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Because not all I3C drivers have the hot-join feature ready, and
especially not all I3C devices support hot-join feature, exporting
SETDASA method could be useful. With this function, the I3C controller
could perform a DAA to I3C devices when users decide to turn these I3C
devices off and on again during run-time.
Tested: This change has been tested with turnning off an I3C device and
turning on it again during run-time. The device driver calls SETDASA
method to perform DAA to the device. And communication between I3C
controller and device is set up again correctly.
Signed-off-by: Jack Chen <zenghuchen@google.com>
Link: https://lore.kernel.org/r/20221207205059.3848851-1-zenghuchen@google.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The reattach should be used when an I3C device has its address changed.
But the modified place in this patch doesn't have the address changed of
the newdev. This wrong reattach will reserve the same address slot twice
and return unexpected -EBUSY when the bus find the duplicate device with
diffent dynamic address.
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20220926105145.8145-2-billy_tsai@aspeedtech.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
This patch is used to free the old_dyn_addr when the caller want to
reattach the device to the different dynamic address. If the
old_dyn_addr is 0 the function will treat it as no old_dyn_addr is
reserved on the bus. Without the patch, when the driver reattach the i3c
device after setnewda the old_dyn_addr will be permanently occupied.
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20220926105145.8145-1-billy_tsai@aspeedtech.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Commit 31b9887c72 ("i3c: remove i2c board info from i2c_dev_desc")
removed the boardinfo from i2c_dev_desc to decouple device enumeration from
setup but did not correctly lookup the i2c_dev_desc to store the new
device, instead dereferencing an uninitialized variable.
Lookup the device that has already been registered by address to store
the i2c client device.
Fixes: 31b9887c72 ("i3c: remove i2c board info from i2c_dev_desc")
Reported-by: kernel test robot <lkp@intel.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Jamie Iles <quic_jiles@quicinc.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20220308134226.1042367-1-quic_jiles@quicinc.com
I2C devices can be added to the system dynamically through several
sources other than static board info including device tree overlays and
sysfs i2c new_device.
Add an I2C bus notifier to attach the clients at runtime if they were
not defined in the board info. For DT devices find the LVR in the reg
property, for user-space new_device additions we synthesize a
conservative setting of no spike filters and fast mode only.
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Jamie Iles <quic_jiles@quicinc.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20220117174816.1963463-3-quic_jiles@quicinc.com
I2C board info is only required during adapter setup so there is no
requirement to keeping a pointer to it once running. To support dynamic
device addition we can't rely on board info - user-space creation
through sysfs won't have a boardinfo.
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Jamie Iles <quic_jiles@quicinc.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20220117174816.1963463-2-quic_jiles@quicinc.com
The address slot bitmap is an array of unsigned long's which are the
same size as an int on 32-bit platforms but not 64-bit. Loading the
bitmap into an int could result in the incorrect status being returned
for a slot and slots being reported as the wrong status.
Fixes: 3a379bbcea ("i3c: Add core I3C infrastructure")
Cc: Boris Brezillon <bbrezillon@kernel.org>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Jamie Iles <quic_jiles@quicinc.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210922165600.179394-1-quic_jiles@quicinc.com
The driver core ignores the return value of this callback because there
is only little it can do when a device disappears.
This is the final bit of a long lasting cleanup quest where several
buses were converted to also return void from their remove callback.
Additionally some resource leaks were fixed that were caused by drivers
returning an error code in the expectation that the driver won't go
away.
With struct bus_type::remove returning void it's prevented that newly
implemented buses return an ignored error code and so don't anticipate
wrong expectations for driver authors.
Reviewed-by: Tom Rix <trix@redhat.com> (For fpga)
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Cornelia Huck <cohuck@redhat.com> (For drivers/s390 and drivers/vfio)
Acked-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> (For ARM, Amba and related parts)
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Chen-Yu Tsai <wens@csie.org> (for sunxi-rsb)
Acked-by: Pali Rohár <pali@kernel.org>
Acked-by: Mauro Carvalho Chehab <mchehab@kernel.org> (for media)
Acked-by: Hans de Goede <hdegoede@redhat.com> (For drivers/platform)
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-By: Vinod Koul <vkoul@kernel.org>
Acked-by: Juergen Gross <jgross@suse.com> (For xen)
Acked-by: Lee Jones <lee.jones@linaro.org> (For mfd)
Acked-by: Johannes Thumshirn <jth@kernel.org> (For mcb)
Acked-by: Johan Hovold <johan@kernel.org>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> (For slimbus)
Acked-by: Kirti Wankhede <kwankhede@nvidia.com> (For vfio)
Acked-by: Maximilian Luz <luzmaximilian@gmail.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> (For ulpi and typec)
Acked-by: Samuel Iglesias Gonsálvez <siglesias@igalia.com> (For ipack)
Acked-by: Geoff Levand <geoff@infradead.org> (For ps3)
Acked-by: Yehezkel Bernat <YehezkelShB@gmail.com> (For thunderbolt)
Acked-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> (For intel_th)
Acked-by: Dominik Brodowski <linux@dominikbrodowski.net> (For pcmcia)
Acked-by: Rafael J. Wysocki <rafael@kernel.org> (For ACPI)
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org> (rpmsg and apr)
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> (For intel-ish-hid)
Acked-by: Dan Williams <dan.j.williams@intel.com> (For CXL, DAX, and NVDIMM)
Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com> (For isa)
Acked-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (For firewire)
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> (For hid)
Acked-by: Thorsten Scherer <t.scherer@eckelmann.de> (For siox)
Acked-by: Sven Van Asbroeck <TheSven73@gmail.com> (For anybuss)
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> (For MMC)
Acked-by: Wolfram Sang <wsa@kernel.org> # for I2C
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Finn Thain <fthain@linux-m68k.org>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20210713193522.1770306-6-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver core ignores the return value of struct bus_type::remove()
because there is only little that can be done. To simplify the quest to
make this function return void, let struct i3c_driver::remove() return
void, too. This makes it obvious that returning an error code is
a bad idea and future driver authors cannot get that wrong.
Up to now there are no drivers with a remove callback, so there is no
need to adapt drivers.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210128091048.17006-2-u.kleine-koenig@pengutronix.de
A registered driver without a probe callback doesn't make sense, so
refuse to register such a driver. (Otherwise i3c_device_probe() yields a
NULL pointer exception.)
A driver without remove is possible, e.g. when all resources are freed
using devm callbacks. So guard the call to driver->remove by a check
for being non-NULL.
Note that the only in-tree i3c driver
(drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_i3c.c) doesn't have a remove
callback.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210128091048.17006-1-u.kleine-koenig@pengutronix.de
This patch fix following issue.
Controller slots blocked for devices with static_addr
but no init_dyn_addr may limit the number of I3C devices
on the bus which gets dynamic address in DAA. So
instead of attaching all the devices with static_addr,
now we only attach the devices which successfully
complete SETDASA. For remaining devices with init_dyn_addr,
i3c_master_add_i3c_dev_locked() will try to set requested
dynamic address after DAA.
Signed-off-by: Parshuram Thombare <pthombar@cadence.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-i3c/1598337109-14770-1-git-send-email-pthombar@cadence.com
Boardinfo was lost if I3C object for devices with boardinfo
available are not created or not added to the I3C device list
because of some failure e.g. SETDASA failed, retrieve info failed etc
This patch adds i3c_master_attach_boardinfo which scan boardinfo list
in the master object and 'attach' it to the I3C device object.
Fixes: 3a379bbcea ("i3c: Add core I3C infrastructure")
Signed-off-by: Parshuram Thombare <pthombar@cadence.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-i3c/1590053542-389-1-git-send-email-pthombar@cadence.com
According to the I3C spec v1.1 document, GETMRL's payload is 2 bytes,
with an optional 3rd byte if the IBI private payload is larger than
1 byte. The whole GETMRL may also be optional so max_ibi_len already
defaults to 1 if BCR_IBI_PAYLOAD prior to the i3c_master_getmrl_locked()
call.
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-i3c/nycvar.YSQ.7.76.2004151623060.2671@knanqh.ubzr
We already have the master device in a variable, reuse it.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Vitor Soares <vitor.soares@synopsys.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-i3c/20200214145853.24762-1-wsa+renesas@sang-engineering.com
i3c_bus_set_mode function is only used in master.c.
Make it static to avoid warning when compiling with W=1.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Since we have i3c_dev_get_master() available, use it.
Signed-off-by: Vitor Soares <vitor.soares@synopsys.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Since we have dev_to_i3cmaster() available, use it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
In i3c_master_getmwl_locked(), the buffer used for the dest payload data is
allocated using kzalloc() in i3c_ccc_cmd_dest_init(). Later on, the length
of the dest payload data is checked against 'sizeof(*mwl)'. If they are not
equal, -EIO is returned to indicate the error. However, the allocated
buffer is not deallocated on this path, leading to a memory leak.
To fix the above issue, free the buffer before returning the error.
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
I need to store address and lvr value for I2C devices without static definition
in DT. This allows secondary master to transmit DEFSLVS command properly.
Main changes between v4 and v5:
- Change in defslvs to use addr and lvr from i2c_dev_desc structure
- Change in CDNS and DW drivers to use addr and lvr from i2c_dev_desc structure
Signed-off-by: Przemyslaw Gaj <pgaj@cadence.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Each iteration of for_each_available_childe_of_node puts the previous
node, but in the case of a return from the middle of the loop, there
is no put, thus causing a memory leak. Add an of_node_put before the
return.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Some I3C device drivers need to know which entry matches the
i3c_device object passed to the probe function
Let's move i3c_device_match_id() to device.c and export it so it can be
used by drivers.
Signed-off-by: Vitor Soares <vitor.soares@synopsys.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes, in particular in the
context in which this code is being used.
So, replace the following form:
sizeof(*defslvs) + ((ndevs - 1) * sizeof(struct i3c_ccc_dev_desc))
with:
struct_size(defslvs, slaves, ndevs - 1)
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
The i3c bus spec defines a bus configuration where i2c devices don't
have a 50ns filter but support SCL running at SDR max rate (12.5MHz).
This patch introduces the limited bus mode so that users can use
a higher speed in presence of i2c devices index 1.
Signed-off-by: Vitor Soares <vitor.soares@synopsys.com>
Cc: Boris Brezillon <bbrezillon@kernel.org>
Cc: <linux-kernel@vger.kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Currently the I3C framework limits SCL frequency to FM speed when
dealing with a mixed slow bus, even if all I2C devices are FM+ capable.
The core was also not accounting for I3C speed limitations when
operating in mixed slow mode and was erroneously using FM+ speed as the
max I2C speed when operating in mixed fast mode.
Fixes: 3a379bbcea ("i3c: Add core I3C infrastructure")
Signed-off-by: Vitor Soares <vitor.soares@synopsys.com>
Cc: Boris Brezillon <bbrezillon@kernel.org>
Cc: <stable@vger.kernel.org>
Cc: <linux-kernel@vger.kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
This patch drops support for I2C devices with 10 bit addressing. When I2C
device with 10 bit address is defined in DT, I3C master registration fails.
Address space for I2C devices has been reduced and ->i2c_funcs() hook has been
removed.
Because this patch series dropped support for 10 bit I2C devices, support is
also dropped in Cadence I3C master driver and Synopsys DesignWare I3C master
driver.
Signed-off-by: Przemyslaw Gaj <pgaj@cadence.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
* Remove dead code in the DW driver
-----BEGIN PGP SIGNATURE-----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=/U9S
-----END PGP SIGNATURE-----
Merge tag 'i3c/for-5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux
Pull i3c update from Boris Brezillon:
- Fix a shift wrap bug in the core
- Remove dead code in the DW driver
* tag 'i3c/for-5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux:
i3c: Fix a shift wrap bug in i3c_bus_set_addr_slot_status()
i3c: master: dw: remove dead code from dw_i3c_master_*_xfers()
The problem here is that addr can be I3C_BROADCAST_ADDR (126). That
means we're shifting by (126 * 2) % 64 which is 60. The
I3C_ADDR_SLOT_STATUS_MASK is an enum which is an unsigned int in GCC
so shifts greater than 31 are undefined.
Fixes: 3a379bbcea ("i3c: Add core I3C infrastructure")
Cc: <stable@vger.kernel.org>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
