Return a negative error code on failure.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret; expression e1,e2;
@@
(
if (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There was another instance where we were
holding pointers which could be long gone.
Fix that by caching only values pointed to
by such pointer.
Because no crash has been observed, this patch
will be sent on v3.19 merge window, instead of
-rc.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Disable the MUSB interrupts till MUSB is recovered fully from BABBLE
condition. There are chances that we could get multiple interrupts
till the time the babble recover work gets scheduled. Sometimes
this could even end up in an endless loop making MUSB itself unusable.
Reported-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There is a poll loop for max 25us for HS devices. Now guess what, I
tested it in gadget mode and forgot about the little detail. Nobody seem
to have it noticed…
This patch adds the missing logic for hostmode so it is recognized in
host and device mode properly.
Fixes: 50aea6fca7 ("usb: musb: cppi41: fire hrtimer according to
programmed channel length")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
musb registers can be dumped using the file regdump
which is created in debugfs. Up to now hard coded
register addresses are used for that. Different glue
layers however have different register addresses. The
patch addresses this issue by substituting bare register
addresses with defines.
Signed-off-by: Roman Byshko <rbyshko@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
On am335x-evm with musb in host mode and using it as a wakeup source the
following happens once the CPU comes out of suspend to ram:
|PM: Wakeup source MPU_WAKE
|PM: noirq resume of devices complete after 15.453 msecs
|PM: early resume of devices complete after 2.222 msecs
|PM: resume of devices complete after 507.351 msecs
|Restarting tasks ...
|------------[ cut here ]------------
|WARNING: CPU: 0 PID: 322 at drivers/usb/core/urb.c:339 usb_submit_urb+0x494/0x4c8()
|URB cc0db380 submitted while active
|[<c0348e64>] (usb_submit_urb) from [<c0340f94>] (hub_activate+0x2b8/0x49c)
|[<c0340f94>] (hub_activate) from [<c03411dc>] (hub_resume+0x14/0x1c)
|[<c03411dc>] (hub_resume) from [<c034be10>] (usb_resume_interface.isra.4+0xdc/0x110)
|[<c034be10>] (usb_resume_interface.isra.4) from [<c034beb0>] (usb_resume_both+0x6c/0x13c)
|[<c034beb0>] (usb_resume_both) from [<c034cca4>] (usb_runtime_resume+0x10/0x14)
|[<c034cca4>] (usb_runtime_resume) from [<c02bbd80>] (__rpm_callback+0x2c/0x60)
|[<c02bbd80>] (__rpm_callback) from [<c02bbdd4>] (rpm_callback+0x20/0x74)
|[<c02bbdd4>] (rpm_callback) from [<c02bcc48>] (rpm_resume+0x380/0x548)
|[<c02bcc48>] (rpm_resume) from [<c02bcb00>] (rpm_resume+0x238/0x548)
|[<c02bcb00>] (rpm_resume) from [<c02bd08c>] (__pm_runtime_resume+0x64/0x94)
|[<c02bd08c>] (__pm_runtime_resume) from [<c034b5a4>] (usb_autopm_get_interface+0x18/0x5c)
|[<c034b5a4>] (usb_autopm_get_interface) from [<c03438b8>] (hub_thread+0x10c/0x115c)
|[<c03438b8>] (hub_thread) from [<c005a70c>] (kthread+0xbc/0xd8)
|---[ end trace 036aa5fe78203142 ]---
|hub 1-0:1.0: activate --> -16
|hub 2-0:1.0: activate --> -16
The reason for this backtrace is the attempt of the USB code to resume
the HUB twice and thus enqueue the status URB twice.
Alan Stern was a great help by explaining how the USB code supposed to
work and what is most likely the problem. The root problem is that after
resume the musb runtime-suspend state remains RPM_SUSPENDED.
According to git log it RPM was added for the omap2430 platform. If I
understand it correct the omap2430 invokes a get on musb once a cable is
connected and a put once the cable is gone. In between the device could
go auto-idle/off. Not sure what happens when the device goes into suspend
but then I guess it was gadget only.
On DSPS I see only a get in probe and put in remove function. This would
forbid RPM from working but then the devices enterns suspended state
anyway :)
To get rid of this warning, I set the device state to RPM_ACTIVE which
the expected state.
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: <stable@vger.kernel.org>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There were a two issues here.
1) We returned PTR_ERR(NULL) which means success if class_create()
failed.
2) If alloc_chrdev_region() failed then we should clean up before
returning.
Also kernel style is to have "error handling" as opposed to "success
handling". In the original code checking for "if (!status) " is
confusing and this bad style is what lead to bug #2.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We free "opts" on the error path and then dereference it.
Fixes: 21a9476a7b ('usb: gadget: hid: add configfs support')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds a UDC driver for Broadcom's USB3.0 Peripheral core named BDC.
BDC supports control traffic on ep0 and bulk/Int/Isoch traffic on all other
endpoints.
[ balbi@ti.com : fix build error on randconfig due to lack of
<linux/dmapool.h> ]
Signed-off-by: Ashwini Pahuja <ashwini.linux@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Update DWC2 kconfig and makefile to support dual-role mode. The platform
file will always get compiled for the case where the controller is directly
connected to the CPU. So for loadable modules, dwc2.ko is built for host,
peripheral, and dual-role mode. The PCI bus interface will be called
dwc2_pci.ko and the platform interface module will be called dwc2_platform.ko.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since platform.c will get built for both Host and Gadget, if we leave the
usb_disabled() call in platform.c, it results in the following build error
when (!USB && USB_GADGET) condition is met.
ERROR: "usb_disabled" [drivers/usb/dwc2/dwc2_platform.ko] undefined!
Since usb_disabled() is mostly used to disable USB host functionality, move
the call the host portion for the DWC2 driver.
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since the dwc2 hcd driver is currently not looking for a clock node during
init, we should not completely fail if there isn't a clock provided.
By assigning clk = NULL, this allows the driver, when configured for dual-role
mode, to be able to continue loading the host portion of the driver when
a clock node is not specified.
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Make dwc2_handle_common_intr call the gadget interrupt function when operating
in peripheral mode. Remove the spinlock functions in s3c_hsotg_irq as
dwc2_handle_common_intr() already has the spinlocks.
Move the registeration of the IRQ to common code for platform and PCI.
Remove duplicate interrupt conditions that was in gadget, as those are handled
by dwc2 common interrupt handler.
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Initialize the USB driver to peripheral mode when a B-Device connector
is attached.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Update suspend/resume to use dev_pm_ops API.
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch will aggregate the probing of gadget/hcd driver into platform.c.
The gadget probe funtion is converted into gadget_init that is now only
responsible for gadget only initialization. All the gadget resources are now
handled by platform.c
Since the host workqueue will not get initialized if the driver is configured
for peripheral mode only. Thus we need to check for wq_otg before calling
queue_work().
Also, we move spin_lock_init to common location for both host and gadget that
is either in platform.c or pci.c.
We also move suspend/resume code to common platform code.
Lastly, move the "samsung,s3c6400-hsotg" binding into dwc2_of_match_table.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Adds the gadget data structure and appropriate data structure pointers
to the common dwc2_hsotg data structure. To keep the driver data
dereference code looking clean, the gadget variable declares are only available
for peripheral and dual-role mode. This is needed so that the dwc2_hsotg data
structure can be used by the hcd and gadget drivers.
Updates gadget.c to use the dwc2_hsotg data structure and gadget pointers
that have been moved into the common dwc2_hsotg structure.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Hcd controller needs bus_suspend/resume, dwc2 controller make
root hub generate suspend/resume signal with hprt0 register
when work in host mode.
After the root hub enter suspend, we can make controller enter
low power state with PCGCTL register.
We also update the lx_state for hsotg state.
This patch has tested on rk3288 with suspend/resume.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch expands USB-DMAC channels for R-Car Gen2 SoCs. The SoCs
have 4 channels. If d{2,3}_{t,x}x_id are not set, this driver never
uses the expanded USB-DMAC channels.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
To extend DnFIFOs in the future, this patch adds a new macro because
some SoCs don't the "port" address for DnFIFOs.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
To expand DnFIFOs in the future, this patch standardizes the d{0,1}fifo
control using new macros.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
To extend DnFIFOs in the future, this patch changes d{0,1}fifo of
usbhs_fifo_info to dfifo array.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
drivers/usb/gadget/function/f_midi.c:1072:21: sparse: symbol 'f_midi_alloc' was not declared. Should it be static?
drivers/usb/gadget/legacy/gmidi.c:118:30: sparse: symbol 'fi_midi' was not declared. Should it be static?
drivers/usb/gadget/legacy/gmidi.c:119:21: sparse: symbol 'f_midi' was not declared. Should it be static?
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
drivers/usb/gadget/function/f_hid.c:852:21: sparse: symbol 'hidg_alloc' was not declared. Should it be static?
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
commit e47d925 (usb: move the OTG state from
the USB PHY to the OTG structure) moved the
OTG state from struct usb_phy to struct usb_otg.
Unfortunately, even though I fixed quite a few
build regressions with that patch already, this
one was still missing.
Note that this driver still has other randconfig
build problems which I'll leave for driver author
to fix, as that's less trivial.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
commit e47d925 (usb: move the OTG state
from the USB PHY to the OTG structure) moved
the OTG state field from struct usb_phy to
struct usb_otg but, even though I fixed many
other build breakages, I still missed one
on ohci-omap.c.
Fix the build breakage now.
drivers/usb/host/ohci-omap.c: In function ‘start_hnp’:
drivers/usb/host/ohci-omap.c:186:19: error: request for member ‘state’ in something not a structure or union
hcd->usb_phy->otg.state = OTG_STATE_A_SUSPEND;
Signed-off-by: Felipe Balbi <balbi@ti.com>
Replace usb_gadget_driver's disconnect with udc-core's reset notifier at
bus reset handler.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Replace usb_gadget_driver's disconnect with udc-core's reset notifier at
bus reset handler.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Replace usb_gadget_driver's disconnect with udc-core's reset notifier at
bus reset handler.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Replace usb_gadget_driver's disconnect with udc-core's reset notifier at
bus reset handler.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Replace usb_gadget_driver's disconnect with udc-core's reset notifier at
bus reset handler.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Replace usb_gadget_driver's disconnect with udc-core's reset notifier at
bus reset handler.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Replace usb_gadget_driver's disconnect with udc-core's reset notifier at
bus reset handler.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Replace usb_gadget_driver's disconnect with udc-core's reset notifier at
bus reset handler.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Replace usb_gadget_driver's disconnect with udc-core's reset notifier at
bus reset handler.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Replace usb_gadget_driver's disconnect with udc-core's reset notifier at
bus reset handler.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Replace usb_gadget_driver's disconnect with udc-core's reset notifier at
bus reset handler.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Replace usb_gadget_driver's disconnect with udc-core's reset notifier at
bus reset handler.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds support for the new udc-core reset notifier to the
net2272 driver.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds support for the new udc-core reset notifier to the
net2280 driver.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Replace usb_gadget_driver's disconnect with udc-core's reset notifier at
bus reset handler.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Peter chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Replace usb_gadget_driver's disconnect with udc-core's reset notifier at
bus reset handler.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Replace usb_gadget_driver's disconnect with udc-core's reset notifier at
bus reset handler.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
SET_FEATURE request with DEBUG_MODE only worked the first time after module
initialisation. Per the USB 2.0 debug device specification, said request
is to be treated as if it were a SET_CONFIGURATION request, i.e. endpoint
must be re-configured.
As configure_endpoints() may now get called multiple times, move it outside
__init and move serial_alloc_tty() call into __init.
Code has assumption that endpoint mapping remains unchanged with consecutive
calls of configure_endpoints().
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The recent change bringing device-tree support triggers a warning in a
non device-tree build :
drivers/usb/gadget/udc/pxa27x_udc.c:2405:28: warning: 'udc_pxa_dt_ids'
defined but not used [-Wunused-variable]
Fix the warning with a preprocessor condition.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Felipe Balbi <balbi@ti.com>
as it turns out, at least AM437x silicon (non-FPGA)
needs to enable PHY suspend quirk. So let's allow
for PHY suspend quirk to be used with non-FPGA
builds too.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Make the hid function available for gadgets composed with configfs.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Before configfs is integrated the usb_gstrings_attach() interface
must be used.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There are no old function interface users left, so remove it.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use the new f_hid interface in order for the old to be removed.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
