To avoid continually doing ISP resets when get loop id fails to
obtain the adapter loop id, first try to do a link initialization.
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If another function on the port has initiated a loopback operation do not
process the current request.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When the Read SFP mailbox command fails on the thermal device,
print a message explaining that thermal is not supported.
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
There's a subtle race in the loop/bus-reset handling whereby a
VHA's loop-state can get incorrectly set to 'down' after the
loop-reset and firmware's completion of link re-negotiation. The
original code incorrectly assumes that firmware AENs would arrive
only after mailbox-command execution to initiate the link-flap.
Here's a good case with the old code (AENs arrive after
mailbox-command completion):
qla2xxx [0000:03:00.1]-8012:91: BUS RESET ISSUED nexus=91:0:4.
qla2xxx [0000:03:00.1]-287d:91: FCPort state transitioned from ONLINE to LOST - portid=010100.
qla2xxx [0000:03:00.1]-580e:91: Asynchronous P2P MODE received.
qla2xxx [0000:03:00.1]-287d:91: FCPort state transitioned from ONLINE to LOST - portid=010400.
qla2xxx [0000:03:00.1]-802b:91: BUS RESET SUCCEEDED nexus=91:0:4.
qla2xxx [0000:03:00.1]-480b:91: Reset marker scheduled.
qla2xxx [0000:03:00.1]-5812:91: Port database changed ffff 0006 0000.
qla2xxx [0000:03:00.1]-505f:91: Link is operational (4 Gbps).
qla2xxx [0000:03:00.1]-480c:91: Reset marker end.
qla2xxx [0000:03:00.1]-480f:91: Loop resync scheduled.
qla2xxx [0000:03:00.1]-8837:91: F/W Ready - OK.
qla2xxx [0000:03:00.1]-883a:91: fw_state=3 (7, 0, 0, 0) curr time=170b8f315.
qla2xxx [0000:03:00.1]-280e:91: HBA in F P2P topology.
qla2xxx [0000:03:00.1]-2812:91: qla2x00_configure_hba success
qla2xxx [0000:03:00.1]-2814:91: Configure loop -- dpc flags = 0x5260.
notice how the 'Port database changed' (8014) arrived after the
bus-reset handler completed 'BUS RESET SUCCEEDED'.
Now, here's a failing case with the old code (AENs arrive before
mailbox-command completion):
qla2xxx [0000:03:00.1]-8012:91: BUS RESET ISSUED nexus=91:0:0.
qla2xxx [0000:03:00.1]-580e:91: Asynchronous P2P MODE received.
qla2xxx [0000:03:00.1]-287d:91: FCPort state transitioned from ONLINE to LOST - portid=010100.
qla2xxx [0000:03:00.1]-287d:91: FCPort state transitioned from ONLINE to LOST - portid=010400.
qla2xxx [0000:03:00.1]-4800:91: DPC handler sleeping.
qla2xxx [0000:03:00.1]-5812:91: Port database changed ffff 0006 0000.
qla2xxx [0000:03:00.1]-505f:91: Link is operational (4 Gbps).
qla2xxx [0000:03:00.1]-802b:91: BUS RESET SUCCEEDED nexus=91:0:0.
qla2xxx [0000:03:00.1]-480b:91: Reset marker scheduled.
qla2xxx [0000:03:00.1]-480c:91: Reset marker end.
qla2xxx [0000:03:00.1]-480f:91: Loop resync scheduled.
qla2xxx [0000:03:00.1]-8837:91: F/W Ready - OK.
qla2xxx [0000:03:00.1]-883a:91: fw_state=3 (7, 0, 0, 0) curr time=170be9eb2.
qla2xxx [0000:03:00.1]-280e:91: HBA in F P2P topology.
qla2xxx [0000:03:00.1]-2812:91: qla2x00_configure_hba success
qla2xxx [0000:03:00.1]-2814:91: Configure loop -- dpc flags = 0x5260.
qla2xxx [0000:03:00.1]-281e:91: Needs RSCN update and loop transition.
qla2xxx [0000:03:00.1]-286a:91: qla2x00_configure_loop *** FAILED ***.
qla2xxx [0000:03:00.1]-4810:91: Loop resync end.
qla2xxx [0000:03:00.1]-4800:91: DPC handler sleeping.
This race would ultimately lead to devices go unexpectedly
offline until another link-flap or chip-reset would cause driver
re-discovery to take place.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Base the number of outstanding requests the driver will keep track of on the
available resources instead of being hard-coded.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
There wasn't any error handling for this kzalloc().
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The error path calls dma_pool_free() on this path but "chap_table" is
NULL and "chap_dma" is uninitialized. It's cleaner to just return
directly.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Root cause is libsas will clear asd_sas_port phy_mask value in sas_port_deform
after triggering destruct workqueue, but the workqueue will send sync cmd and
still need phy_mask value. Now, mvsas using asd_sas_phy setting instead of
asd_sas_port setting.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Delete successive tests to the same location. The code tested the result
of a previous allocation, that itself was already tested. It is changed to
test the result of the most recent allocation.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@s exists@
local idexpression y;
expression x,e;
@@
*if ( \(x == NULL\|IS_ERR(x)\|y != 0\) )
{ ... when forall
return ...; }
... when != \(y = e\|y += e\|y -= e\|y |= e\|y &= e\|y++\|y--\|&y\)
when != \(XT_GETPAGE(...,y)\|WMI_CMD_BUF(...)\)
*if ( \(x == NULL\|IS_ERR(x)\|y != 0\) )
{ ... when forall
return ...; }
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
While reading sysfs chap_in_idx and chap_out_idx attribute, if chap
authentication is not set we get an error as "Invalid argument".
Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Boot from SAN fails in some cases where boot target login response
is slow. In this case, probe finishes early and triggers init, which
doesn't find remote disk to mount root which leads to BFS failure.
Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch force driver to collect firmware dump using following command:-
"echo 2 > /sys/class/scsi_host/hostX/device/fw_dump"
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Problem:
If initialization of adapter fails for some reason, then the interrupt handlers
are released. The interrupt handlers are not registered again when initialization
of adapter is retried.
Solution:
Re-register the interrupt handler when adapter initialization is retried.
Signed-off-by: Poornima Vonti <poornima.vonti@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Problem:
QLA4xxx firmware may assert if given more IOCBs than it can handle.
Solution:
The driver was updated to throttle the number of active IOCBs based
on the total number of IOCB buffers received from get_firmware_status
mbx_sts[2].
Signed-off-by: Karen Higgins <karen.higgins@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Removed unnecessary calls to qla4xxx_get_firmware_status from
function qla4xxx_init_local_data
Signed-off-by: Karen Higgins <karen.higgins@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Quiesce all different activities performed by driver upon the link events
while loopback diagnostics is in progress.
Signed-off-by: Nilesh Javali <nilesh.javali@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The spurious interrupt messages are seen when interrupt lines are
shared between different adapters or modules. Example, interrupt
lines are shared between qlcnic and qla4xxx and USB modules, then the
console is flooded with flurry of spurious interrupt messages
which are expected in such scenario.
Hence put these messages under debug level 2 for INTx interrupt mode.
Signed-off-by: Nilesh Javali <nilesh.javali@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When doing a hotplug remove of a cxgb4 device, there are still dandling
symlinks at /sys/class/scsi_host/hostX to the removed PCI device. The
upper layer device may also try to send data, which may crash the
system.
The DETACH message from the lower level driver is sent to the ULD when
the device is removed, when the scsi host should be removed from the
system, avoiding any problems.
After this patch, there are no more dangling symlinks and many attempts
to crash the system while there is SCSI activity and removing the device
have failed. Adding the device back again works as expected, with the
scsi hosts showing up again.
Based on a patch by Karen Xie.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Cc: Karen Xie <kxie@chelsio.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The closing parenthesis is in the wrong place so it takes the sizeof a
pointer instead of the sizeof the buffer minus one.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Anil Gurumurthy <agurumur@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Check mbox_sts[3] instead of mbox_sts[4] for ISP83xx to validate size
of data returned
Signed-off-by: Nilesh Javali <nilesh.javali@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Fixed no-context ABTS received on unsolicited receive queue failed with BA_RJT
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Removed use of NOP mailboxes for interrupt verification in pci_probe_one_s4
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch fixes the following sparse error:
CHECK drivers/scsi/ipr.c
spinlock.h:147:9: warning: context imbalance in 'ipr_reset_reload' - unexpected unlock
Signed-off-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch implements blk iopoll in ipr driver for performance improvement.
Signed-off-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch reduces lock contention while implementing distributed
completion processing.
Signed-off-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The new generation IBM SAS Controllers will support MSI-X interrupts and
Distributed Completion Processing features. This patch add these support
in ipr device driver.
Signed-off-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The resource path as displayed by the ipr driver is the
location string identifying a location on the SAS fabric.
This patch adds the SCSI host number such that error logs
can be more easily correlated in multiple adapter configurations.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
