According to Bspec FW_BLC_SELF exists on 915G also. Let's program it.
The only open question is whether there's is a memory self-refresh
enable bit somewhere as well. For 945G/GM it's in FW_BLC_SELF, for
915GM it's in INSTPM. For 915G I can't find one in the docs. Let's drop
a FIXME about this, in case someone with the hardware is ever bored
enough to look for it.
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1469804222-12650-2-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Bspec says:
"FW_BLC_SELF
...
Programming Note [DevALV] and [DevCST]: When calculating watermark
values for 15/16bpp, assume 32bpp for purposes of calculation using
the high priority bandwidth analysis spreadsheet."
Let's do that.
Perhaps this might even help with the problem that resulted in
commit 2ab1bc9df0 ("drm/i915: Disable self-refresh for untiled fbs on i915gm")
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1469804222-12650-1-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
In the middle of intel_gt_init_powersave() we have an if-chain that ends
with a universal else clause to read gen6+ registers. Older platforms
like Pineview that end up here do not like those registers and may even
OOPS whilst reading them!
Fixes: 3ea9a80132 ("drm/i915: Perform static RPS frequency setup ...")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470132927-1821-1-git-send-email-chris@chris-wilson.co.uk
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
SNB (and IVB too I suppose) starts to misbehave if the GPU gets stuck
in an infinite batch buffer loop. The GPU apparently hogs something
critical and CPUs start to lose interrupts and whatnot. We can keep
the system limping along by unmasking some interrupts in
GEN6_PMINTRMSK. The EI up interrupt has been previously chosen for
that task, so let's never mask it.
v2: s/gen6_rps_pm_mask/gen6_sanitize_rps_pm_mask/ (Chris)
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=93122
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1464014568-4529-1-git-send-email-ville.syrjala@linux.intel.com
Cc: stable@vger.kernel.org
Now that PCU communication is reasonably fast, we do not need to defer
RC6 initialisation to a workqueue.
References: https://bugs.freedesktop.org/show_bug.cgi?id=97017
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Since commit a6f766f397 ("drm/i915: Limit ring synchronisation (sw
sempahores) RPS boosts") and commit bcafc4e38b ("drm/i915: Limit mmio
flip RPS boosts") we have limited the waitboosting for semaphores and
flips. Ideally we do not want to boost in either of these instances as no
userspace consumer is waiting upon the results (though a userspace producer
may be stalled trying to submit an execbuf - but in this case the
producer is being throttled due to the engine being saturated with
work). With the introduction of NO_WAITBOOST in the previous patch, we
can finally disable these needless boosts.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1469002875-2335-6-git-send-email-chris@chris-wilson.co.uk
This function is no longer used outside of intel_pm.c so we can stop
exposing it and rename the __gen6_update_ring_freq() to take its place.
Suggested-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1468397438-21226-8-git-send-email-chris@chris-wilson.co.uk
Some hardware requires a valid render context before it can initiate
rc6 power gating of the GPU; the default state of the GPU is not
sufficient and may lead to undefined behaviour. The first execution of
any batch will load the "golden render state", at which point it is safe
to enable rc6. As we do not forcibly load the kernel context at resume,
we have to hook into the batch submission to be sure that the render
state is setup before enabling rc6.
However, since we don't enable powersaving until that first batch, we
queued a delayed task in order to guarantee that the batch is indeed
submitted.
v2: Rearrange intel_disable_gt_powersave() to match.
v3: Apply user specified cur_freq (or idle_freq if not set).
v4: Give in, and supply a delayed work to autoenable rc6
v5: Mika suggested a couple of better names for delayed_resume_work
v6: Rebalance rpm_put around the autoenable task
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1468397438-21226-7-git-send-email-chris@chris-wilson.co.uk
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
To allow the user finer control over waitboosting, allow them to set the
frequency we request for the boost. This also them allows to effectively
disable the boosting by setting the boost request to a low frequency.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1468397438-21226-5-git-send-email-chris@chris-wilson.co.uk
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Select idle frequency during initialisation, then reset the last known
frequency when re-enabling. This allows us to preserve the user selected
frequency across resets.
v2: Stop CHV from overriding the user's choice in cherryview_enable_rps()
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1468397438-21226-2-git-send-email-chris@chris-wilson.co.uk
Since drm_i915_private is now a subclass of drm_device we do not need to
chase the drm_i915_private->dev backpointer and can instead simply
access drm_i915_private->drm directly.
text data bss dec hex filename
1068757 4565 416 1073738 10624a drivers/gpu/drm/i915/i915.ko
1066949 4565 416 1071930 105b3a drivers/gpu/drm/i915/i915.ko
Created by the coccinelle script:
@@
struct drm_i915_private *d;
identifier i;
@@
(
- d->dev->i
+ d->drm.i
|
- d->dev
+ &d->drm
)
and for good measure the dev_priv->dev backpointer was removed entirely.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1467711623-2905-4-git-send-email-chris@chris-wilson.co.uk
Since we now subclass struct drm_device, we can save pointer dances by
noting the equivalence of struct drm_device and struct drm_i915_private,
i.e. by using to_i915().
text data bss dec hex filename
1073824 4562 416 1078802 107612 drivers/gpu/drm/i915/i915.ko
1068976 4562 416 1073954 106322 drivers/gpu/drm/i915/i915.ko
Created by the coccinelle script:
@@
expression E;
identifier p;
@@
- struct drm_i915_private *p = E->dev_private;
+ struct drm_i915_private *p = to_i915(E);
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Dave Gordon <david.s.gordon@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1467628477-25379-1-git-send-email-chris@chris-wilson.co.uk
Make sure that the RPS bottom-half is flushed before we set the idle
frequency when we decide the GPU is idle. This should prevent any races
with the bottom-half and setting the idle frequency, and ensures that
the bottom-half is bounded by the GPU's rpm reference taken for when it
is active (i.e. between gen6_rps_busy() and gen6_rps_idle()).
v2: Avoid recursively using the i915->wq - RPS does not touch the
struct_mutex so has no place being on the ordered i915->wq.
v3: Enable/disable interrupts for RPS busy/idle in order to prevent
further HW access from RPS outside of the wakeref.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
References: https://bugs.freedesktop.org/show_bug.cgi?id=89728
Reviewed-by: Michał Winiarski <michal.winiarski@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1467616119-4093-6-git-send-email-chris@chris-wilson.co.uk
The retire worker is a low frequency task that makes sure we retire
outstanding requests if userspace is being lax. We only need to start it
once as it remains active until the GPU is idle, so do a cheap test
before the more expensive queue_work(). A consequence of this is that we
need correct locking in the worker to make the hot path of request
submission cheap. To keep the symmetry and keep hangcheck strictly bound
by the GPU's wakelock, we move the cancel_sync(hangcheck) to the idle
worker before dropping the wakelock.
v2: Guard against RCU fouling the breadcrumbs bottom-half whilst we kick
the waiter.
v3: Remove the wakeref assertion squelching (now we hold a wakeref for
the hangcheck, any rpm error there is genuine).
v4: To prevent excess work when retiring requests, we split the busy
flag into two, a boolean to denote whether we hold the wakeref and a
bitmask of active engines.
v5: Reorder cancelling hangcheck upon idling to avoid a race where we
might cancel a hangcheck after being preempted by a new task
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
References: https://bugs.freedesktop.org/show_bug.cgi?id=88437
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1467616119-4093-1-git-send-email-chris@chris-wilson.co.uk
When waiting for an interrupt (waiting for the engine to complete some
work), we know we are the only waiter to be woken on this engine. We also
know when the GPU has nearly completed our request (or at least started
processing it), so after being woken and we detect that the GPU is
active and working on our request, allow us the bottom-half (the first
waiter who wakes up to handle checking the seqno after the interrupt) to
spin for a very short while to reduce client latencies.
The impact is minimal, there was an improvement to the realtime-vs-many
clients case, but exporting the function proves useful later. However,
it is tempting to adjust irq_seqno_barrier to include the spin. The
problem is first ensuring that the "start-of-request" seqno is coherent
as we use that as our basis for judging when it is ok to spin. If we
could, spinning there could dramatically shorten some sleeps, and allow
us to make the barriers more conservative to handle missed seqno writes
on more platforms (all gen7+ are known to have the occasional issue, at
least).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1467390209-3576-7-git-send-email-chris@chris-wilson.co.uk
BXT BIOS has two options related to GPU power management: "RC6(Render
Standby)" and "GT PM Support". The assumption so far was that disabling
either of these options would leave RC6 uninitialized. According to my
tests this isn't so: for a proper RC6 setup we only need the "GT PM
Support" option to be enabled while the "RC6" option only controls
whether RC6 is left enabled or not by BIOS. OTOH we were missing a few
checks to ensure a proper RC6 setup. Add these now and don't fail the
sanity check if RC6 is disabled. This fixes a problem where RC6 remains
disabled after reloading the driver, since we explicitly disable RC6
during unloading.
v2:
- Print a debug message about the BIOS enabled RC state. (Sagar)
CC: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1467216835-1086-2-git-send-email-imre.deak@intel.com
We want to replace the inline wait_for() with an out-of-line hybrid
busy/sleep wait_for() in the hopes of speeding up the communication wit
the PCode unit.
Indeed, on my i5-2500s, __gen6_update_ring_freq improves from
6,080,661ns to 8172ns.
v2: Missed using _fw variants for sandybridge_pcode_read()
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1467297225-21379-2-git-send-email-chris@chris-wilson.co.uk
When a display update triggers a DDB re-allocation, we should start by
assuming that only the updated pipes need to be re-allocated (we have
logic later that may add additional pipes if, e.g., a modeset triggers a
change to the global allocation).
We were erroneously using the _active_ pipes as our starting point
rather than the changed pipes. This causes us to grab CRTC locks that
we didn't actually need, reducing parallelism. Given the recent
non-blocking atomic changes, it also causes legacy pageflips against one
CRTC to return -EBUSY if there's an outstanding pageflip against a
different CRTC (a situation easily triggered via compositors like
Weston).
Fixes: 98d39494d3 ("drm/i915/gen9: Compute DDB allocation at atomic check time (v4)")
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1467070964-14864-1-git-send-email-matthew.d.roper@intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
If the GPU load is low enough, it's possible that we'll be stuck at idle
frequency rather than transition into softmin frequency requested by
userspace.
v2: Use intel_set_rps, drop vlv_set_idle
v3: Back to vlv_set_idle, clamp to valid range
v4: Place intel_set_rps at the end
References: https://bugs.freedesktop.org/show_bug.cgi?id=89728
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1466416707-12075-1-git-send-email-michal.winiarski@intel.com
Bspec states that we need to set nuke on modify all to prevent
screen corruption with fbc on skl and kbl.
v2: proper workaround name
References: HSD#2227109, HSDES#1404569388
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465309159-30531-27-git-send-email-mika.kuoppala@intel.com
Set bit 8 in 0x43224 to prevent screen corruption and system
hangs on high memory bandwidth conditions. The same wa also suggest
setting bit 31 on ARB_CTL. According to another workaround we gain
better idle power savings when FBC is enabled.
v2: use correct workaround name
v3: split out overlapping wa for corruption avoidance (Ville)
References: HSD#2137218, HSD#2227171, HSD#2136579, BSID#883
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465309159-30531-26-git-send-email-mika.kuoppala@intel.com
According to bspec this prevents screen corruption when fbc is
used.
v2: This workaround has a name, use it (Ville)
v3: remove bogus gen check on ilk/vlv wm path (Ville)
References: HSD#2135555, HSD#2137270, BSID#562
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465309159-30531-25-git-send-email-mika.kuoppala@intel.com
According to bspec this workaround helps to reduce lag and improve
performance on edp.
Documentation suggests this for bdw and all gen9. However evidence
shows that this register is missing on gen9 and causing unclaimed mmio
access if we access it. So apply to bdw only where the reg
exists and can hold its value.
v2: drop skl
References: HSD#2134579
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465309159-30531-11-git-send-email-mika.kuoppala@intel.com
if downscaling is enabled plane data rate increases according to scaling
amount. take scaling amount under consideration while calculating plane
data rate
v2: Address Matt's comments, where data rate was overridden because of
missing else.
v3 (by Matt):
- Add braces to 'else' branch to match kernel coding style
- Adjust final calculation now that skl_plane_downscale_amount()
returns 16.16 fixed point value instead of a decimal fixed point
v4 (by Matt):
- Avoid integer overflow by making sure final multiplication is
treated as 64-bit.
Cc: matthew.d.roper@intel.com
Signed-off-by: Kumar, Mahesh <mahesh1.kumar@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Kumar Mahesh <mahesh1.kumar@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463695381-21368-1-git-send-email-matthew.d.roper@intel.com
Don't use pipe pixel rate for plane pixel rate. Calculate plane pixel according
to formula
adjusted plane_pixel_rate = adjusted pipe_pixel_rate * downscale ammount
downscale amount = max[1, src_h/dst_h] * max[1, src_w/dst_w]
if 90/270 rotation use rotated width & height
v2: use intel_plane_state->visible instead of (fb == NULL) as per Matt's
comment.
v3 (by Matt):
- Keep downscale amount in 16.16 fixed point rather than converting to
decimal fixed point.
- Store adjusted plane pixel rate in plane state instead of the plane
parameters structure that we no longer use.
v4 (by Matt):
- Significant rebasing onto latest atomic watermark work
- Don't bother storing plane pixel rate in state; just calculate it
right before the calls that make use of it.
- Fix downscale calculations to actually use width values when
computing downscale_w rather than copy/pasted height values.
Cc: matthew.d.roper@intel.com
Signed-off-by: Kumar, Mahesh <mahesh1.kumar@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Kumar Mahesh <mahesh1.kumar@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463439121-28974-4-git-send-email-matthew.d.roper@intel.com
don't always use 8 ddb as minimum, instead calculate using proper
algorithm.
v2: optimizations as per Matt's comments.
v3 (by Matt):
- Fix boolean logic for !fb test in skl_ddb_min_alloc()
- Adjust negative tiling format comparisons in skl_ddb_min_alloc() to
improve readability.
v4 (by Matt):
- Rebase onto recent atomic watermark changes
- Slight tweaks to code flow to make the logic more closely match the
description in the bspec.
v5 (by Matt):
- Handle minimum scanline calculation properly for 4 & 8 bpp formats.
8bpp isn't actually possible right now, but it's listed in the bspec
so I've included it here for forward compatibility (similar to how
we have logic for NV12).
v6 (by Matt):
- Calculate plane_bpp correctly for non-NV12 formats. (Mahesh)
Cc: matthew.d.roper@intel.com
Signed-off-by: Kumar, Mahesh <mahesh1.kumar@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Kumar Mahesh <mahesh1.kumar@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464713939-10440-1-git-send-email-matthew.d.roper@intel.com
We don't actually read out full plane state during driver startup (only
whether the primary plane is enabled/disabled), so all of the src/dest
rectangles are invalid at this point. However this calculation was
needless anyway since we re-calculate them from scratch on the very
first atomic transaction after boot anyway.
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Kumar Mahesh <mahesh1.kumar@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463439121-28974-2-git-send-email-matthew.d.roper@intel.com
For now, anything with a GuC requires uCode loading, and then supports
command submission once loaded. But these are logically distinct from
simply "having a GuC", so we need a separate macro for the latter. Then,
various tests should use this new macro rather than HAS_GUC_UCODE() or
testing enable_guc_submission.
v4:
Added a couple more uses of the new macro.
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Found this while browsing Bspec. Looks like it applies to both skl and
kbl.
v2: Also for bxt (Art).
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Sonika Jindal <sonika.jindal@intel.com>
Cc: Durgadoss R <durgadoss.r@intel.com>
Cc: "Pandiyan, Dhinakaran" <dhinakaran.pandiyan@intel.com>
Cc: "Runyan, Arthur J" <arthur.j.runyan@intel.com>
Reviewed-by: Sonika Jindal<sonika.jindal@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463642060-30728-1-git-send-email-daniel.vetter@ffwll.ch
When we read out the watermark state from the hardware we're supposed to
transfer that into the active watermarks, but currently we fail to any
part of the active watermarks that isn't explicitly written. Let's clear
it all upfront.
Looks like this has been like this since the beginning, when I added the
readout. No idea why I didn't clear it up.
Cc: Matt Roper <matthew.d.roper@intel.com>
Fixes: 243e6a44b9 ("drm/i915: Init HSW watermark tracking in intel_modeset_setup_hw_state()")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463151318-14719-2-git-send-email-ville.syrjala@linux.intel.com
If we can't find any valid level 0 watermark values for the requested
atomic transaction, reject the configuration before we try to start
programming the hardware.
v2:
- Add extra debugging output when we reject level 0 watermarks so that
we can more easily debug how/why they were rejected.
Cc: Lyude Paul <cpaul@redhat.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463061971-19638-17-git-send-email-matthew.d.roper@intel.com
Moving watermark calculation into the check phase will allow us to to
reject display configurations for which there are no valid watermark
values before we start trying to program the hardware (although those
tests will come in a subsequent patch).
Another advantage of moving this calculation to the check phase is that
we can calculate the watermarks in a single shot as part of the atomic
transaction. The watermark interfaces we inherited from our legacy
modesetting days are a bit broken in the atomic design because they use
per-crtc entry points but actually re-calculate and re-program something
that is really more of a global state. That worked okay in the legacy
modesetting world because operations only ever updated a single CRTC at
a time. However in the atomic world, a transaction can involve multiple
CRTC's, which means we wind up computing and programming the watermarks
NxN times (where N is the number of CRTC's involved). With this patch
we eliminate the redundant re-calculation of watermark data for atomic
states (which was the cause of the WARN_ON(!wm_changed) problems that
have plagued us for a while).
We still need to work on the 'commit' side of watermark handling so that
we aren't doing redundant NxN programming of watermarks, but that's
content for future patches.
v2:
- Bail out of skl_write_wm_values() if the CRTC isn't active. Now that
we set dirty_pipes to ~0 if the active pipes change (because
we need to deal with DDB changes), we can now wind up here for
disabled pipes, whereas we couldn't before.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=89055
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=92181
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Tested-by: Daniel Stone <daniels@collabora.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463091100-13747-1-git-send-email-matthew.d.roper@intel.com
Once we move watermark calculation to the atomic check phase, we'll want
to start rejecting display configurations that exceed out watermark
limits. At the moment we just assume that there's always a valid set of
watermarks, even though this may not actually be true. Let's prepare by
passing return codes up through the call stack in preparation.
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463061971-19638-15-git-send-email-matthew.d.roper@intel.com
In an upcoming patch we'll move this calculation to the atomic 'check'
phase so that the display update can be rejected early if no valid
watermark programming is possible.
v2:
- Drop intel_pstate_for_cstate_plane() helper and add note about how
the code needs to evolve in the future if we start allowing more than
one pending commit against a CRTC. (Maarten)
v3:
- Only have skl_compute_wm_level calculate watermarks for enabled
planes; we can just set the other planes on a CRTC to disabled
without having to look at the plane state. This is important because
despite our CRTC lock we can still have racing commits that modify
a disabled plane's property without turning it on. (Maarten)
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463061971-19638-13-git-send-email-matthew.d.roper@intel.com
Now that we're properly pre-allocating the DDB during the atomic check
phase and we trust that the allocation is appropriate, let's actually
use the allocation computed and not duplicate that work during the
commit phase.
v2:
- Significant rebasing now that we can use cached data rates and
minimum block allocations to avoid grabbing additional plane states.
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463061971-19638-11-git-send-email-matthew.d.roper@intel.com
