This patch adds a port map for ICH9 and ICH8 SATA controllers that have only 2 ports available in that mode.
Signed-off-by: Jason Gaston <jason.d.gaston@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This is a driver for the ATA controller on the Geode CS5536 companion
chip. The PCI device ID for this device was previously claimed by
pata_amd.c but the PIO timings were not correct. This driver also
works around a bug in some BIOSes that handle unaligned access to the
PCI config registers poorly. Finally, the driver allows fallback to
using MSR registers for configuration on BIOSes that are truly
broken.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
After commands which can change device configuration, EH is scheduled
to revalidate and reconfigure the device. Host link was incorrectly
used unconditionally when scheduling EH action. This resulted in
bogus revalidation request and mismatched configuration between device
and driver. Fix it.
This bug was reported by Igor Durdanovic.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Igor Durdanovic <idurdanovic@comcast.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add the Software NCQ support to sata_nv.c for MCP51/MCP55/MCP61 SATA
controller. NCQ function is disable by default, you can enable it
with 'swncq=1'. NCQ will be turned off if the drive is Maxtor on
MCP51 or MCP55 rev 0xa2 platform.
[akpm@linux-foundation.org: build fix]
Signed-off-by: Kuan Luo <kluo@nvidia.com>
Signed-off-by: Peer Chen <pchen@nvidia.com>
Cc: Zoltan Boszormenyi <zboszor@dunaweb.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch adds MMIO support to the pata_sil680 for taskfile IOs,
based on what the old siimage does.
I haven't bothered changing the chip setup stuff from PCI config
cycles to MMIO though (siimage does it), I don't think it matters,
I've only adapted it to use MMIO for taskfile accesses.
I've tested it on a Cell blade and it seems to work fine.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* remove pointless pci_dev_to_dev() wrapper. Just directly reference
the embedded struct device like everyone else does.
* pata_cs5520: delete cs5520_remove_one(), it was a duplicate of
ata_pci_remove_one()
* linux/libata.h: don't bother including linux/pci.h, we don't need it.
Simply declare 'struct pci_dev' and assume interested parties will
include the header, as they should be doing anyway.
* linux/libata.h: consolidate all CONFIG_PCI declarations into a
single location in the header.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
PMP registers used to be accessed with dedicated accessors ->pmp_read
and ->pmp_write. During reset, those callbacks are called with the
port frozen so they should be able to run without depending on
interrupt delivery. To achieve this, they were implemented polling.
However, as resetting the host port makes the PMP to isolate fan-out
ports until SError.X is cleared, resetting fan-out ports while port is
frozen doesn't buy much additional safety.
This patch updates libata PMP support such that PMP registers are
accessed using regular ata_exec_internal() mechanism and kills
->pmp_read/write() callbacks. The following changes are made.
* PMP access helpers - sata_pmp_read_init_tf(), sata_pmp_read_val(),
sata_pmp_write_init_tf() are folded into sata_pmp_read/write() which
are now standalone PMP register access functions.
* sata_pmp_read/write() returns err_mask instead of rc. This is
consistent with other functions which issue internal commands and
allows more detailed error reporting.
* ahci interrupt handler is modified to ignore BAD_PMP and
spurious/illegal completion IRQs while reset is in progress. These
conditions are expected during reset.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Implement ATA_PFLAG_RESETTING. This flag is set while reset is in
progress. It's set before prereset is called and cleared after reset
fails or postreset is finished.
This flag itself doesn't have any function. It will be used by LLDs
to tell whether reset is in progress if it needs to behave differently
during reset.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add @timeout argument to ata_exec_internal[_sg](). If 0, default
timeout ata_probe_timeout is used.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Asynchronous notification on ICH9 didn't work because it didn't write
AN FIS into the RX area - it only updates SNotification. Also,
snooping SDB_FIS RX area is racy against further SDB FIS receptions.
Let sata_async_notification() determine using SNTF if it's available
and snoop RX area iff SNTF isn't available
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Now that we have pp->intr_mask, move PORT_IRQ_BAD_PMP enabling to
ahci_pmp_attach/detach() where it belongs.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ahci had problems with NCQ over PMP and NCQ used to be disabled while
PMP was attached. After fixing the problem, the temporary NCQ
disabling code wasn't removed completely. Kill the remaining piece.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Tasks in uninterruptible sleep might be woken up by unrelated events
and should check whether the condition it was waiting for has actually
triggered. Wrap schedule_timeout_uninterruptible() in loop to achieve
it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ATA_EHI_NO_AUTOPSY and ATA_EHI_QUIET are used during initial probing
to skip exception analysis and reporting. Usually, there's nothing to
report but on some allowed but rare corner cases (e.g. phy status
changed interrupt when IRQ is enabled on frozen port - this happens if
IRQ pending status isn't cleared in the IRQ router or controller)
exception messages get printed.
Skip reporting if ATA_EHI_QUIET is set.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ehi description field is used to carry LLD specific controller
description. Sometimes, it's used without clearing before and LLD
description gets printed with exception information one more time.
Clear after printing.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
PATA part of all current JMB controllers behave the same way and
JMicron confirms that all future ones will stay compatible. Drop
device matching and match only vendor and class.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Ethan Hsiao <ethanhsiao@jmicron.com>
Cc: Justin Tsai <justin@jmicron.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
On a cable there may be
eighty wires or perhaps forty
and we learn about its type
In the world of ACPI
So we call the GTM
And we find the the timing rate
And we look through it to see
If eighty wire it must be
Timing lives in ACPI routines
ACPI routines, ACPI routines
Timing lives in ACPI routines
ACPI routes ACPI routines
And the drivers last you see
Picking up unknown pci ids
and the code begins to work
Timing lives in ACPI routines
ACPI routines, ACPI routines
Timing lives in ACPI routines
ACPI routes ACPI routines
[Full speed ahead, Mr Hacker, full speed ahead]
Full speed over here sir!
Checking Cable, checking cable
Aye aye, 80 wire,
Heaven heaven]
If we use ACPI (ACPI)
Every box (every box) has all we need (has all we need)
Cable type (cable type) and mode timing (mode timing)
In our ATA (in our ATA) subroutines (subroutines, ha ha)
Timing lives in ACPI routines
ACPI routines, ACPI routines
Timing lives in ACPI routines
ACPI routes ACPI routines
Timing lives in ACPI routines
ACPI routines, ACPI routines
Timing lives in ACPI routines
ACPI routes ACPI routines
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Talk to the dark side our driver has to, yes. Much misleading is the
data. Store it in a structure we do so that it may be parsed.
Signed-off-by: Alan Cox <alan@redhat.com>
--
Whats small, old and shouts phrases out of order across mountains ?
Yodla..
Signed-off-by: Jeff Garzik <jeff@garzik.org>
HDT722516DLA380 does spurious completion of NCQ commands. Blacklist
it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Frans Pop <elendil@planet.nl>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Seagate Barracuda ST380817AS has troubles with NCQ. For example,
unpacking a tarball on an XFS filesystem gives this:
ata1.00: exception Emask 0x0 SAct 0x1 SErr 0x0 action 0x2 frozen
ata1.00: cmd 61/40:00:29:a3:98/00:00:00:00:00/40 tag 0 cdb 0x0 data 32768 out
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
More info here:
http://lkml.org/lkml/2007/1/21/76
Blacklist it!
Signed-off-by: Paolo Ornati <ornati@fastwebnet.it>
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some controller variants snoop the ATAPI length value for Packet
transfers to do state machine and FIFO management. Thus we want to
set it properly, even for cases where it is otherwise meaningless.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Correct handling of SRST reset sequences. After an SRST it is undefined
whether the drive has gone back to PIO0. In order to talk safely we should
talk slowly and carefully until we know.
Thus when we do the reset if the controller has a pio setup method we call it
to flip back to PIO 0 and a known state. After the reset completes the
identify will then be done at the safe speed and the drive/controller will
pick suitable faster modes and reconfigure the controller to these timings.
As a side effect it means we force the controller to PIO 0 as we bring it up
which fixes funnies on a few systems where the BIOS firmware leaves us in an
interesting choice of modes, or embedded boxes with no firmware which come up
in random states.
For smart controllers there is nothing to do - they know about this
internally.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Modern laptops with hotswap bays still tend to utilise a PATA interface
on a SATA bridge, generally with the host controller in some legacy
emulation mode rather than AHCI. This means that the existing hotplug
code in libata is unable to work. The ACPI specification states that
these devices can send notifications when hotswapped, which avoids the
need to obtain notification from the controller. This patch uses the
existing libata-acpi code and simply registers a notification in order
to trigger a rescan whenever the firmware signals an event.
Signed-off-by: Matthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This is useful when debugging, handling problem systems, or for
distributions just to get the system installed so it can be sorted
out later.
This is a bit smarter than the old IDE one and lets you do
libata.dma=0 Disable all PATA DMA like old IDE
libata.dma=1 Disk DMA only
libata.dma=2 ATAPI DMA only
libata.dma=4 CF DMA only
(or combinations thereof - 0,1,3 being the useful ones I suspect)
(I've split CF as it seems to be a seperate case of pain and suffering
different to the others and caused by assorted PIO wired adapters etc)
Signed-off-by: Alan Cox <alan@redhat.com>
[edited to work on SATA too, changing name from 'pata_dma' to 'dma']
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This adds human-readable decoding of the ATA status and error registers
(similar to what drivers/ide does) as well as the SATA Serror register
to libata error handling output. This prevents the need to pore
through standards documents to figure out the meaning of the bits
in these registers when looking at error reports. Some bits that
drivers/ide decoded are not decoded here, since the bits are either
command-dependent or obsolete, and properly parsing them would add
too much complexity.
Signed-off-by: Robert Hancock <hancockr@shaw.ca>
[edited slightly to make output a bit more symmetric]
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Of course some controllers lie about PMP support. Black list them.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Private pi.flags area is full and we need more private flags. Move
host private flags over to pi.private_data. During initialization,
these flags are copied to hpriv->flags.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Implement AHCI PMP support. ahci only supports command based
switching. Also, for some reason, NCQ over PMP doesn't work now.
Other than that, everything works.
Tested on ICH9R, JMB360/363 + SIMG3726, 4726 and 5744.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Forrest Zhao <forrest.zhao@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
As DEV_RST (hardreset) sometimes fail to recover the controller
(especially after PMP DMA CS errata). In such cases, perform PORT_RST
prior to DEV_RST.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Implement PMP support. sil24 supports full FIS-switching. However,
it has a PMP DMA CS errata which requires port-wide resetting if
commands are outstanding to three or more devices when an error occurs
on one of them.
ATAPI commands often result in CHECK SENSE and it's crucial to not
reset them before fetching sense data. Unfortunately, ATAPI CHECK
SENSE causes a lot of problem if command is outstanding to any other
device usually resulting in port-wide reset. So, sata_sil24
implements sil24_qc_defer() which guarantees ATAPI command is run by
itself.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Extend ata_acpi_associate_sata_port() such that it can handle PMP and
call it when PMP is attached and detached.
Build breakage when !CONFIG_ATA_ACPI was spotted and fixed by Petr
Vandrovec.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Petr Vandrovec <petr@vandrovec.name>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Hook PMP support into libata and enable it. Connect SCR and probing
functions, and update ata_dev_classify() to detect PMP.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Implement Port Multiplier support. To support PMP, a LLDD has to
supply ops->pmp_read() and pmp_write(). If non-null, ->pmp_attach and
->pmp_detach are called on PMP attach and detach, respectively.
->pmp_read/write() can be called while the port is frozen, so they
must be implemented by polling. This patch supplies several helpers
to ease ->pmp_read/write() implementation.
Also, irq_handler and error_handler must be PMP aware. Most of PMP
aware EH can be done by calling ata_pmp_do_eh() with appropriate
methods. PMP EH uses separate set of reset methods and this patch
implements standard prereset, hardreset and postreset methods.
This patch only implements PMP support. The next patch will integrate
PMP into the reset of libata and thus enable PMP support.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
PMP always requires SRST to be enabled. Also, hardreset reports
classification code from the first device when PMP is attached, not
from the PMP. Update ata_eh_reset() such that followup softreset is
performed if the controller is PMP capable and the host link is being
reset.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Restore the support for handling drives that report one sector too many
(ie SCSI not ATA style). This worked before the HPA update but was
removed in that process.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Blacklist HITACHI HDS7250SASUN500G and HITACHI HDS7225SBSUN250G
drives using wildcard matching.
Signed-off-by David Milburn <dmilburn@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* The firmware version of ST3160812AS is "3.ADJ" no "3.AD".
* Add several entries from various sources.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
I've been doing an audit of this driver to try and find out why we have
problems with some Clevo boxes that use it. Didn't get anywhere other
than to discover all the bug reporters I have use vmware, which may or
may not be chance.
In the process however I did find out our MWDMA2 performance was a bit
low and code review showed the MWDMA0/2 timings are reversed due to a
thinko in the table ordering
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
AHCI spec says host-reset bit may only be set when the ahci-enable bit
is also set.
Noticed by Peer Chen <peerchen@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Little fixlets, that the build started erroring / warning about:
drivers/ata/pata_scc.c: In function 'scc_bmdma_status':
drivers/ata/pata_scc.c:734: error: structure has no member named 'active_tag'
drivers/ata/pata_scc.c: In function 'scc_pata_prereset':
drivers/ata/pata_scc.c:866: warning: passing arg 1 of 'ata_std_prereset' from incompatible pointer type
drivers/ata/pata_scc.c: In function 'scc_error_handler':
drivers/ata/pata_scc.c:908: warning: passing arg 2 of 'ata_bmdma_drive_eh' from incompatible pointer type
drivers/ata/pata_scc.c:908: warning: passing arg 3 of 'ata_bmdma_drive_eh' from incompatible pointer type
drivers/ata/pata_scc.c:908: warning: passing arg 5 of 'ata_bmdma_drive_eh' from incompatible pointer type
make[2]: *** [drivers/ata/pata_scc.o] Error 1
Signed-off-by: Satyam Sharma <satyam@infradead.org>
Cc: Alan Cox <alan@redhat.com>
Cc: Mel Gorman <mel@skynet.ie>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The SATA_PATA_SHARING register doesn't have anything to do with the
SATA part of the controller. It indicates whether an extern SATA PHY
is attached to the PATA part of the controller and if so how it is
wired. As the PATA part is driven by pata_via, sata_via has no reason
to care about that. Also, pata_via should work fine under all
configurations.
This patch removes unnecessary attach failures. It seems recent via
chipsets are defaulting to different values or are actually connected
to SATA PHY triggering this more often.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In ata_set_max_sectors(), the highest nibble in LBA28 mode was
missing. This made drives sized between 8G and 128G with HPA turned
on to be resized to under 8G. Fix it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
AN serves multiple purposes. For ATAPI, it's used for media change
notification. For PMP, for downstream PHY status change notification.
Implement sata_async_notification() which demultiplexes AN.
To avoid unnecessary port events, ATAPI AN is not enabled if PMP is
attached but SNTF is not available.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Kriten Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some pseudo devices fail PM commands unnecessarily aborting system
suspend. Implement ATA_HORKAGE_SKIP_PM which makes libata skip PM
commands for these devices.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
If PMP itself becomes inaccessible while trying to link a downstream
link, spending time to recover the downstream link doesn't make any
sense. Make EH skip retry and fail fast if -ERESTART is received.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Implement ATA_LFLAG_DISABLED. The flag indicates the link is disabled
due to EH recovery failure. While a link is disabled, no EH action is
taken on the link and suspend/resume become noop too.
This will be used by PMP links to manage failed links.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some PMP links are connected to internal pseudo devices which may come
and go depending on situation. There's no reason to try hard to
recover them. ATA_LFLAG_NO_RETRY tells EH to not retry if the device
attached to the link fails.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some links on some PMPs locks up on SRST and/or report incorrect
device signature. Implement ATA_LFLAG_NO_SRST, ASSUME_ATA and
ASSUME_SEMB to handle these quirky links. NO_SRST makes EH avoid
SRST. ASSUME_ATA and SEMB forces class code to ATA and SEMB_UNSUP
respectively. Note that SEMB isn't currently supported yet so the
_UNSUP variant is used.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Implement ap->nr_active_links (the number of links with active qcs),
ap->excl_link (pointer to link which can be used by ->qc_defer and is
cleared when a qc with ATA_QCFLAG_CLEAR_EXCL completes), and
ata_link_active().
These can be used by ->qc_defer() to implement proper command
exclusion. This set of helpers seem enough for both sil24 (ATAPI
exclusion needed) and cmd-switching PMP.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Controllers which support PMP have various restrictions on which
combinations of commands are allowed to what number of devices
concurrently. This patch implements ops->qc_defer() which determines
whether a qc can be issued at the moment or should be deferred.
If the function returns ATA_DEFER_LINK, the qc will be deferred until
a qc completes on the link. If ATA_DEFER_PORT, until a qc completes
on any link. The defer conditions are advisory and in general
ATA_DEFER_LINK can be considered as lower priority deferring than
ATA_DEFER_PORT.
ops->qc_defer() replaces fixed ata_scmd_need_defer(). For standard
NCQ/non-NCQ exclusion, ata_std_qc_defer() is implemented. ahci and
sata_sil24 are converted to use ata_std_qc_defer().
ops->qc_defer() is heavier than the original mechanism because full qc
is prepped before determining to defer it, but various information is
needed to determine defer conditinos and fully translating a qc is the
only way to supply such information in generic manner.
IMHO, this shouldn't cause any noticeable performance issues as
* for most cases deferring occurs rarely (except for NCQ-aware
cmd-switching PMP)
* translation itself isn't that expensive
* once deferred the command won't be repeated until another command
completes which usually is a very long time cpu-wise.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make a number of functions from libata-core.c and libata-eh.c global
to libata (drivers/ata/libata.h). These will be used by PMP.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Consider newly found class code while revalidating. PMP resetting
always results in valid class code and issuing PMP commands to
ATA/ATAPI device isn't very attractive. Add @new_class to
ata_dev_revalidate() and check class code for revalidation.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Update AN support in preparation of PMP support.
* s/ata_id_has_AN/ata_id_has_atapi_AN/
* add AN enabled reporting during configuration
* add err_mask to AN configuration failure reporting
* update LOCKING comment for ata_scsi_media_change_notify()
* check whether ATA dev is attached to SCSI dev ata_scsi_media_change_notify()
* set ATA_FLAG_AN in ahci and sata_sil24
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Kriten Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Clear ARRE, we don't do auto-reallocation on reads, just on writes.
Also, hardcode the size of the array using RW_RECOVERY_MPAGE_LEN,
following the style of the surrounding code.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* SAT specifies that FORMAT UNIT should be translated into a series
of READ and WRITE commands that zero the ATA device. That is far too
cumbersome to bother with.
Since we don't actually format the device, the old behavior of
always returning success was inaccurate. Change FORMAT UNIT from
returning success immediately (old behavior) to always returning
an error (new behavior).
* Add some comments around SYNCHRONIZE CACHE
* Shuffle scsi command code around a bit, so that things are close
to alphabetic order.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
A few pedantic apps care about missing or lame "mandatory" SCSI
commands, so
REQUEST SENSE -- as we autosense, R.S. just returns zeroes
SEND DIAGNOSTIC -- our default (no-op) self-test succeeds, all
other requests for testing fail.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Certain device which reports diagnostic failure also reports invalid
device signature. Assume ATA_DEV_ATA on diagnostic failure if reset
indicates device presence.
This is fix for bugzilla bug 8784.
http://bugzilla.kernel.org/show_bug.cgi?id=8784
Signed-off-by: Tejun Heo <htejun@gmail.com>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Edward Amsden <amsden_linux@earthlink.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make ata_dev_try_classify() take a pointer to ata_device instead of
ata_port/port_number combination for consistency and add @present
argument. @present indicates whether the device seems present during
reset. It's the result of TF access during softreset and link
onlineness during hardreset. @present will be used to improve
diagnostic failure handling.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Reimplement port_map handling such that
1. Non-zero PORTS_IMPL value is always examined and used if consistent
with cap.n_ports.
2. When PI and cat.n_ports are inconsistent, honor cap.n_ports and
force port_map to be ((1 << cap.n_ports) - 1).
3. There were two separate places dealing with port_map. Unify them
to one.
As all newer ahci chips seem to get PI correct and older ones usually
have zero PI. Controllers with holes in PI are very unlikely to screw
up PI, so #2 makes more sense than following inconsistent PI.
Without this change, not setting ATA_FLAG_HONOR_PI when it's needed
results in weird detection failure. This changed logic should be able
to handle all known cases correctly automatically.
Verified on ICH6 (reports 0 PI), ICH8 (with holes in port_map), ICH9,
JMB360 and JMB363.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch reimplement ata_hpa_resize() such that...
* All HPA related decisions are made inside ata_hpa_resize() proper.
ata_hpa_resize() returns 0 if configuration can proceed, -errno if
device needs to be reset and reconfigured.
* All errors are handled properly. If HPA unlocking isn't requested,
HPA handling is disabled automatically to avoid unnecessary device
detection failure.
* Messages are trimmed. HPA detection message is printed only during
initial configuration. HPA unlocked message is printed only during
initial configuration or unlocking results in different size.
* Instead of using sectors returned in TF of SET_MAX, re-read IDENTIFY
data as that's the value the device is going to use.
* It's called early during ata_dev_configure() as IDENTIFY data might
change after resizing.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Merge ata_read_native_max_addres_ext() into ata_read_native_max_address()
and combine ata_set_native_max_address_ext() and
ata_set_native_max_address() into ata_set_max_sectors().
* reduce duplicate code
* return 0 or -errno depending on error conditions
* report if command fails
* use ATA_LBA instead of 0x40
This is in preparation of ata_hpa_resize() update.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Move ata_id_n_sectors() upward right below ata_id_c_string(). This is
to accomodate later changes.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch removes some incorrect formatting spaces and replaces them with tabs.
Signed-off-by: Jason Gaston <jason.d.gaston@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
simple search-and-replace of direct scsi_cmnd access to
use the data buffer accessors.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This is a minimal patch needed to remove use of !use_sg
but it is not a complete clean up of the !use_sg paths.
Libata-core still has the qc->flags & ATA_QCFLAG_SG
and !qc->n_elem code paths. Perhaps an ata maintainer
would have a go at it.
- TODO: further cleanup of qc->flags & ATA_QCFLAG_SG
and !qc->n_elem code paths in libata-core
- TODO: Use scsi_dma_{map,unmap} where applicable.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some iomap functions were still using readl/writel and friends which
happens to work on most platforms but is not correct.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Support the use of '*' in model_num and model_rev entries
in ata_device_blacklist[].
Based largely on David Milburn's "libata-core: support wildcard matching
in ata_blacklist_entry" patch.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Updated and simplified driver. Use only register transfer timing for both
data and register transfers. This gives poorer performance in PIO1 and 2,
but should not be a problem in PIO3 and 4, correct me if I'm wrong :)
The driver works very we'll but I still wonder about the interrupts. I have
an interrupt line, that works nicely when POLLING flag is not set. The
problem is the number of interrupts that eat away my CPU cycles.
When using the POLLING flag there seem to be some interrupts that dosen't get
cleared. Furthermore the device dosen't drive INTRQ high, it stays at 2.5 volts
and generates a lot of interrupts due to ripple / noise. What to do?
Signed-off-by: Kristoffer Nyborg Gregertsen <kngregertsen@norway.atmel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix all issues pointed out in Jeff's email.
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
EH is sometimes repeated without any error or action. For example,
this happens when probing IDENTIFY fails because of a phantom device.
In these cases, all the repeated EH does is making sure there is no
unhandled error or pending action and return. This repeation is
necessary to avoid losing any event which occurred while EH was in
progress.
Unfortunately, this dry run causes annonying "EH pending after
completion" message. This patch moves the repeat reporting into
ata_eh_report() such that it's more compact and skipped on dry runs.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Mikael Pettersson <mikep@it.uu.se>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Currently, port configuration reporting has the following problems.
* iomapped address is reported instead of raw address
* report contains irrelevant fields or lacks necessary fields for
non-SFF controllers.
* host->irq/irq2 are there just for reporting and hacky.
This patch implements and uses ata_port_desc() and
ata_port_pbar_desc(). ata_port_desc() is almost identical to
ata_ehi_push_desc() except that it takes @ap instead of @ehi, has no
locking requirement, can only be used during host initialization and "
" is used as separator instead of ", ". ata_port_pbar_desc() is a
helper to ease reporting of a PCI BAR or an offsetted address into it.
LLD pushes whatever description it wants using the above two
functions. The accumulated description is printed on host
registration after "[S/P]ATA max MAX_XFERMODE ".
SFF init helpers and ata_host_activate() automatically add
descriptions for addresses and irq respectively, so only LLDs which
isn't standard SFF need to add custom descriptions. In many cases,
such controllers need to report different things anyway.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Minor cleanup to remove the unneeded rmb()s per Jeff's advice. Also removed the
pll_clock < 0 check since pll_clock now guaranteed to be >= 0 after Mikael's patch.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
If we have a PATA cable with a SATA drive on it then we've found a
bridge and we can flip the cable type. This fixes some cable detect
problems with SATA bridges on chipsets and misdetected cable types.
In theory cable detection and mode limiting is needed if you put a
SATA/PATA bridge on a 40 wire cable, but I see no way to deal with
that other than to point out its not a good idea anyway.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This avoids allocating DMA buffers if not needed but at the moment is
mostly just a neatness item.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
It was always set to ata_port_disable(). Removed the hook, and replaced
the very few ap->ops->port_disable() callsites with direct calls to
ata_port_disable().
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Testing this on the VIA boards fixes several problems with otherwise
undetectable SATA bridge chips
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
We can make use of this on the pata_amd driver as many Nvidia devices
don't have reliable cable detect.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Combined from two Alan Cox patches:
1) libata: ACPI checks for 80wire cable
We can use the ACPI mode information with several drivers as a hint to
cable type. If the ACPI mode set by the BIOS is faster than UDMA33 then
we know the BIOS thinks there are 80wire cables. If it doesn't set such a
mode or it has no ACPI method then we get no further information and can
rely on existing approaches
Introduce the function headers needed. Null it out for non ACPI boxes
Signed-off-by: Alan Cox <alan@redhat.com>
2) libata: ACPI checks for 80wire cable
Provide actual methods for checking if the ACPI support thinks the cable
is 80wire, or doesn't know
Signed-off-by: Alan Cox <alan@redhat.com>
Combined into a single changeset and
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* ->irq_ack() is redundant to what the irq handler already
performs... chk-status + irq-clear. Furthermore, it is only
called in one place, when screaming-irq-debugging is enabled,
so we don't want to bother with a hook just for that.
* ata_dummy_irq_on() is only ever used in drivers that have
no callpath reaching ->irq_on(). Remove .irq_on hook from
those drivers, and the now-unused ata_dummy_irq_on()
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Remove unneeded, undesirable cast of void*.
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Sonic Zhang <sonic.adi@gmail.com>
Cc: Tejun Heo <htejun@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
There is another outstanding issue with ata_piix.c. Intel has never
officially supported anything faster than PATA 100MB/s.
But, the ata_piix.c driver "define" the ICH5 & ICH7 as UDMA6 (aka 133MB/s)
capable. [ Well, no one has probably noticed it before, because there is bug
in do_pata_set_dmamode... Just look at
libata_atapiix_enable_real_udma133.patch and you'll see what wrong with it. ]
Here are Intel's datasheets for the affected chipsets: ICH5 Datasheet:
http://www.intel.com/design/chipsets/datashts/252516.htm (See note on page
183: "... the ICH5 supports reads at the maximum rate of 100MB/s.")
ICH7 Datasheet: http://www.intel.com/design/chipsets/datashts/307013.htm (See
first note on page 190: "... the ICH7 supports reads at the maximum rate of
100MB/s.")
They are two different ways to deal with it:
- Either -
1. replace all ich_pata_133 with ich_pata_100.
(libata_atapiix_disable_udma6.diff - diff from 2.6.22 )
- Or -
2. keep all ich_pata_133 and fix the bug in "do_pata_set_dmamode".
(libata_atapiix_enable_real_udma133.patch - diff from 2.6.22) If there are
any concerns about the safety of the patch patch:
http://lkml.org/lkml/2007/7/6/292 (It was already tested by an Intel
employee, but I guess a bit more user input is necessary here... )
This patch implements 1.
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use a stored value for which interrupts to enable. Changing this allows
us to selectively turn off certain interrupts later and have them
stay off.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
When we get an SDB FIS with the 'N' bit set, we should send
an event to user space to indicate that there has been a
media change. This will be done via the scsi device.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Check to see if an ATAPI device supports Asynchronous Notification.
If so, enable it, if the host controller supports AN.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Set the MWDMA timing by updating the correct registers. Split the PIO path as
this is mostly shared code. Wants testing.
Signed-off-by: Alan Cox <alan@redhat.com>
Tested-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Remembered this while doing auditing and code review versus the specs
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add support for issuing ATA_16 passthru commands to ATAPI devices
managed by libata. It requires the previous CDB length fix patch.
A boot/module parameter, "atapi_passthru16=0" can be used to globally
disable this feature, if ever desired.
tj: restructured __ata_scsi_queuecmd() according to Jeff's suggestion.
Signed-off-by: Mark Lord <liml@rtr.ca>
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Move ata_altstatus() out from ata_hsm_move() to the pio data xfer
functions like ata_pio_sectors() and atapi_pio_bytes() where it makes
more sense.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Debugging a report of a problem with an ancient solid state disk showed
up some problems in the IORDY handling
1. We check the wrong bit to see if the device has IORDY
2. Even then some ancient creaking piles of crap don't support
SETXFER at all.
The cases it fixes are obscure and the risk of side effects is slight
but possible. This also moves us slightly closer to supporting original
MFM/RLL disks with libata.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Update hotplug to handle PMP links. When PMP is attached, the PMP
number corresponds to C of SCSI H:C:I:L. While at it, change argument
to ata_find_dev() to @devno from @id to avoid confusion with SCSI
device ID.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Update ata_eh_autopsy(), ata_eh_report(),
ata_eh_revalidate_and_attach() and ata_eh_recover() to deal with PMP
links. ata_eh_autopsy() and ata_eh_report() updates are
straightforward. They just repeat the same operation over all
configured links. The only change to ata_eh_revalidate_and_attach()
is avoiding calling ->cable_select() on non-host ports.
ata_eh_recover() update is more complex as it first processes all
resets and then performs the rest. This is necessary as thawing with
some links in unknown state can be dangerous. ehi->action is cleared
on successful recovery of a link to avoid repeating recovery due to
failures in other links.
ata_eh_recover() iterates over only PMP links if PMP is attached, and,
on failure, the failing link is returned in @failed_link instead of
disabling devices directly. These are to integrate ata_eh_recover()
into PMP EH later.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Update ata_scsi_error() to handle PMP links. As error conditions can
occur on both host and PMP links, __ata_port_for_each_link() is used.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add link->pmp, ap->nr_pmp_links, ap->pmp_link[], and implement/update
link helpers.
printk helpers are updated such that port and link are identifed as
'ataP:' if no PMP is attached, while device is identified as
'ataP.DD:'. If PMP is attached, they become 'ataP:', 'ataP.LL:' and
'ataP.LL' - ie. link and device are identified their PMP number.
If PPM is attached (ap->nr_pmp_links != 0), ata_for_each_link()
iterates over PMP links, while __ata_for_each_link() iterates over the
host link + PMP links. If PMP is not attached (ap->nr_pmp_links ==
0), both iterate over only the host link.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Separate out link initialization into ata_link_init() and
ata_link_init_sata_spd().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
HRST_TO_RESUME and SKIP_D2H_BSY are link attributes. Move them to
ata_link->flags. This will allow host and PMP links to have different
attributes. ata_port_info->link_flags is added and used by LLDs to
specify these flags during initialization.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make the following functions deal with ata_link instead of ata_port.
* ata_set_mode()
* ata_eh_autopsy() and related functions
* ata_eh_report() and related functions
* suspend/resume related functions
* ata_eh_recover() and related functions
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make reset methods and related functions deal with ata_link instead of
ata_port.
* ata_do_reset()
* ata_eh_reset()
* all prereset/reset/postreset methods and related functions
This patch introduces no behavior change.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make ata_eh_about_to_do() and ata_eh_done() deal with ata_link instead
of ata_port.
This patch introduces no behavior change.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make the following PHY-related functions to deal with ata_link instead
of ata_port.
* sata_print_link_status()
* sata_down_spd_limit()
* ata_set_sata_spd_limit() and friends
* sata_link_debounce/resume()
* sata_scr_valid/read/write/write_flush()
* ata_link_on/offline()
This patch introduces no behavior change.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Multiple links and different number of devices per link should be
considered to iterate over links and devices. This patch implements
and uses link and device iterators - ata_port_for_each_link() and
ata_link_for_each_dev() - and ata_link_max_devices().
This change makes a lot of functions iterate over only possible
devices instead of from dev 0 to dev ATA_MAX_DEVICES. All such
changes have been examined and nothing should be broken.
While at it, add a separating comment before device helpers to
distinguish them better from link helpers and others.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Introduce ata_link. It abstracts PHY and sits between ata_port and
ata_device. This new level of abstraction is necessary to support
SATA Port Multiplier, which basically adds a bunch of links (PHYs) to
a ATA host port. Fields related to command execution, spd_limit and
EH are per-link and thus moved to ata_link.
This patch only defines the host link. Multiple link handling will be
added later. Also, a lot of ap->link derefences are added but many of
them will be removed as each part is converted to deal directly with
ata_link instead of ata_port.
This patch introduces no behavior change.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* corruption fix: we only want the lower 16 bits of length (0 == 64kb)
* ditto: the upper layer sets max-phys-segments to LIBATA_MAX_PRD,
so we must reset it to own hw-specific length.
* delete unused mv_fill_sg() return value
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Three main sets of changes:
1) dmi_get_system_info() return value should have been marked const,
since callers should not be changing that data.
2) const-ify DMI internals, since DMI firmware tables should,
whenever possible, be marked const to ensure we never ever write to
that data area.
3) const-ify DMI API, to enable marking tables const where possible
in low-level drivers.
And if we're really lucky, this might enable some additional
optimizations on the part of the compiler.
The bulk of the changes are #2 and #3, which are interrelated. #1 could
have been a separate patch, but it was so small compared to the others,
it was easier to roll it into this changeset.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The recent mv_fill_sg() rewrite, to fix a data corruption problem
related to IOMMU virtual merging, forgot to account for the
potentially-increased size of the scatter/gather table after its run.
Additionally, the DMA boundary is reduced from 0xffffffff to 0xffff
to more closely match the needs of mv_fill_sg().
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
pata_marvell, use ioread* for iomap-ped memory
read* on pci_iomapped memory is incorrect, fix it
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix bug in sata_mv for cases where the IOMMU layer has merged SG entries
to larger than 64KB. They need to be split up before being sent to
the driver.
Just for simplicity's sake, split up at 64K boundary instead of 64K size,
since that's what the common code does anyway.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
There's a different version of DMI table for TECRA M3 where it has
proper vendor and product name entry. Add the entry to the broken
suspend list.
Angus Turnbull reported and provided initial patch.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Angus Turnbull <angus@twinhelix.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
sis_66_set_dmamode() also handles early UDMA100 (SIS630 ET) but is
missing udma timing value for UDMA100. According to sis5513, this
should be 0x8000. This caused UDMA100 device to fail on pata_sis till
it downgrades to UDMA66 while it works fine on sis5513 at UDMA100.
Reported by Adam Blech.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Adam Blech <desaster.area@addcom.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
When PCIX_IRQ_WOC is used, sil24 has an inherent race condition
between clearing IRQ pending and reading IRQ status. If IRQ pending
is cleared after reading IRQ status, there's possibility of lost IRQ.
If IRQ pending is cleared before reading IRQ status, spurious IRQs
will occur.
sata_sil24 till now cleared IRQ pending after reading IRQ status thus
losing IRQs on machines where PCIX_IRQ_WOC was used. Reverse the
order and ignore spurious IRQs if PCIX_IRQ_WOC.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ATI/AMD SB800 shares some device IDs with SB700,
and SB800 adds two more device IDs:0x4394,0x4395.
Signed-off-by: henry su <henry.su.ati@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Code moved to ioread/iowrite but the comment didn't
Also note a posting issue
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add Toshiba S1800-814 to whitelist for both pata_ali and alim15x3,
as it is correctly detected as 40-wire connected but this cable is
short enough to still use transfer modes higher than UDMA33.
Signed-off-by: Daniel Exner <dex@dragonslave.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
dev->horkage should be cleared over device hotunplug/plug. Clear it
in ata_dev_init().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix "lost" interrupt problem when using dma with CD/DVD drives in some
configurations. This problem can make installing linux from media
impossible for distro's that have switched to libata-only configurations.
The simple fix is to eliminate the use of dma for reading drive status, etc,
by checking the number of bytes to transferred.
This change will only affect the behavior of atapi devices, not disks.
There is more info at http://bugzilla.redhat.com/show_bug.cgi?id=242229
This patch is for 2.6.22.1
Signed-off-by: Jeff Norden <jnorden@math.tntech.edu>
Reviewed-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
I think that I've found and fixed the problem. There is a copy/paste bug in
vt6421_set_dma_mode() function which causes wrong values to be written to
PATA_UDMA_TIMING register.
This patch fixes a copy/paste bug that breaks DMA modes on VT6421 PATA port.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some notebooks need bit18 of IOCFG to be cleared for the drive bay to
work even though the bit is NOOP according to the datasheet. This
patch implement IOCFG bit18 quirk and apply it to Clevo M570U.
http://bugzilla.kernel.org/show_bug.cgi?id=8051
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: D. Angelis <dangelis@beta-cae.gr>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some drives choke on READ_NATIVE_MAX_ADDRESS[_EXT]. Implement
ATA_HORKAGE_BROKEN_HPA and apply it to affected drives.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch corrects sata_promise to classify FastTrack TX4200
(DID 3515/3519) as a second-generation chip. Promise's partial-
source FT TX4200 driver confirms this classification.
Treating it as a first-generation chip causes several problems:
1. Detection failures. This is a recent regression triggered by
the hotplug-enabling changes in 2.6.23-rc1.
2. Various "failed to resume link for reset" warnings.
This patch fixes <http://bugzilla.kernel.org/show_bug.cgi?id=8936>.
Thanks to Stephen Ziemba for reporting the bug and for testing the fix.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Tested-by: Stephen Ziemba <sziemba@ecn.purdue.edu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Satellite U200 also shares the problem. Add it to the broken suspend
list. Original patch from John Schember.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: John Schember <john@nachtimwald.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Resend trying to remove 8-bit characters in the email.
This patch adds the Intel Tolapai IDE mode SATA controller DID's.
Signed-off-by: Jason Gaston <jason.d.gaston@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
On some early drives (pre ATA1) this feature is not supported. If it
fails then we know the drive geometry is the hardware geometry and the
one we tried to set anyway so just carry on.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata: don't check n_sectors during revalidation if zero
pata_via: Add Arima W730-K8 and other rebadgings
pata_sis: Add the FSC Amilo and friends
pata_pdc2027x: PLL detection fixes
libata: fix n_sectors failure handling during revalidation
Whoever did the PCI revision patch slipped up on the it821x, and I
didn't spot this at the time either. They moved the check for the
errata from the 0x10 revision to 0x11. Put it back
This one is important for 2.6.23 final as in some cases bad things will
occur if 0x10 revision boards don't get the fixups.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
