* Document the possibility to pass relative GPIO pin numbers.
* Document what platform device IDs to use, so that they do not
collide.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Peter Korsgaard <peter.korsgaard@barco.com>
The code instantiating an i2c-mux-gpio platform device doesn't
necessarily know in advance the GPIO pin numbers it wants to use. If
pins are on a GPIO device which gets its base GPIO number assigned
dynamically at run-time, the values can't be hard-coded.
In that case, let the caller tell i2c-mux-gpio the name of the GPIO
chip and the (relative) GPIO pin numbers to use. At probe time, the
i2c-mux-gpio driver will look for the chip and apply the proper offset
to turn relative GPIO pin numbers to absolute GPIO pin numbers.
The same could be (and was so far) done on the caller's end, however
doing it in i2c-mux-gpio has two benefits:
* It avoids duplicating the code on every caller's side (about 30
lines of code.)
* It allows for deferred probing for the muxed part of the I2C bus
only. If finding the GPIO chip is the caller's responsibility, then
deferred probing (if the GPIO chip isn't there yet) will not only
affect the mux and the I2C bus segments behind it, but also the I2C
bus trunk.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Peter Korsgaard <peter.korsgaard@barco.com>
Use the devm_kzalloc managed function to stripdown the error and remove
code.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add support for SMBus multiplexing on Asus Z8 motherboard series. On
these boards, the memory slots are behind a GPIO-controlled I2C
multiplexer. Models with 6 or 12 memory slots have 2 segments behind
the multiplexer, while models with 18 memory slots have 3 such
segments.
On these boards, only the memory slots are behind the multiplexer,
so it is possible to keep the autodetection mechanism.
The code is generic enough so it could work on other boards as long as
the multiplexer is controlled by GPIO pins. For other forms of
multiplexing (for example using an I2C device) additional code will be
needed.
Thanks to Asus for providing a board to develop and test this feature,
as well as all the technical information required.
At the moment, the GPIO driver must be loaded before the i2c-i801
driver, but I hope to solve this soon, using deferred probing on
the i2c-mux-gpio side.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The SMBus controller in the VIA VX900 appears to be compatible with
the VIA VX855, so just add the device ID.
This closes kernel bug #43096.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
i2c_dw_xfer_msg is only called internally so it can be static. It
original was, before the driver split. No idea why it was changed at
that time.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Dirk Brandewie <dirk.brandewie@gmail.com>
Replace printks with pr_<level>s, add pr_fmt()s to replace NAMEs
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Reviewed-by: Joe Perches <joe@perches.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Remove the global dependency of the I2C subsystem on HAS_IOMEM and
move the dependency to the i2c/busses submenu, with an exception for
i2c-stub.
The generic I2C part does not need to have HAS_IOMEM set and thus now
becomes available in UML, so the I2C subsystem can now be used, e.g.
by the i2c-stub driver, for development of I2C device drivers.
[JD: Some adjustments.]
[Heiko Carstens: Keep I2C disabled on S390.]
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Convert the struct i2c_msg initialization to C99 format. This makes
maintaining and editing the code simpler. Also helps once other fields
like transferred are added in future.
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Converting kzalloc to devm_kzalloc simplifies the code and ensures that the
result, alert, is freed after the irq allocated by the subsequent
devm_request_irq. This in turn ensures that when an interrupt can be
triggered, the alert structure is still available.
The problem of a free after a devm_request_irq was found using the
following semantic match (http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
expression e1,e2,x,a,b,c,d;
identifier free;
position p1,p2;
@@
devm_request_irq@p1(e1,e2,...,x)
... when any
when != e2 = a
when != x = b
if (...) {
... when != e2 = c
when != x = d
free@p2(...,x,...);
...
return ...;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Let I2C bus segments behind multiplexers have a class. This allows for
device auto-detection on these segments. As long as parent segments
don't share the same class, it should be fine.
I implemented support in drivers i2c-mux-gpio and i2c-mux-pca954x. I
left i2c-mux-pca9541 and i2c-mux-pinctrl alone for the moment as I
don't know if this feature makes sense for the use cases of these
drivers.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Peter Korsgaard <peter.korsgaard@barco.com>
Cc: David Daney <david.daney@cavium.com>
Cc: Michael Lawnick <ml.lawnick@gmx.de>
Cc: Rodolfo Giometti <giometti@linux.it>
Pull powerpc updates from Benjamin Herrenschmidt:
"Some highlights in addition to the usual batch of fixes:
- 64TB address space support for 64-bit processes by Aneesh Kumar
- Gavin Shan did a major cleanup & re-organization of our EEH support
code (IBM fancy PCI error handling & recovery infrastructure) which
paves the way for supporting different platform backends, along
with some rework of the PCIe code for the PowerNV platform in order
to remove home made resource allocations and instead use the
generic code (which is possible after some small improvements to it
done by Gavin).
- Uprobes support by Ananth N Mavinakayanahalli
- A pile of embedded updates from Freescale folks, including new SoC
and board supports, more KVM stuff including preparing for 64-bit
BookE KVM support, ePAPR 1.1 updates, etc..."
Fixup trivial conflicts in drivers/scsi/ipr.c
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (146 commits)
powerpc/iommu: Fix multiple issues with IOMMU pools code
powerpc: Fix VMX fix for memcpy case
driver/mtd:IFC NAND:Initialise internal SRAM before any write
powerpc/fsl-pci: use 'Header Type' to identify PCIE mode
powerpc/eeh: Don't release eeh_mutex in eeh_phb_pe_get
powerpc: Remove tlb batching hack for nighthawk
powerpc: Set paca->data_offset = 0 for boot cpu
powerpc/perf: Sample only if SIAR-Valid bit is set in P7+
powerpc/fsl-pci: fix warning when CONFIG_SWIOTLB is disabled
powerpc/mpc85xx: Update interrupt handling for IFC controller
powerpc/85xx: Enable USB support in p1023rds_defconfig
powerpc/smp: Do not disable IPI interrupts during suspend
powerpc/eeh: Fix crash on converting OF node to edev
powerpc/eeh: Lock module while handling EEH event
powerpc/kprobe: Don't emulate store when kprobe stwu r1
powerpc/kprobe: Complete kprobe and migrate exception frame
powerpc/kprobe: Introduce a new thread flag
powerpc: Remove unused __get_user64() and __put_user64()
powerpc/eeh: Global mutex to protect PE tree
powerpc/eeh: Remove EEH PE for normal PCI hotplug
...
Pull networking changes from David Miller:
"The most important bit in here is the fix for input route caching from
Eric Dumazet, it's a shame we couldn't fully analyze this in time for
3.6 as it's a 3.6 regression introduced by the routing cache removal.
Anyways, will send quickly to -stable after you pull this in.
Other changes of note:
1) Fix lockdep splats in team and bonding, from Eric Dumazet.
2) IPV6 adds link local route even when there is no link local
address, from Nicolas Dichtel.
3) Fix ixgbe PTP implementation, from Jacob Keller.
4) Fix excessive stack usage in cxgb4 driver, from Vipul Pandya.
5) MAC length computed improperly in VLAN demux, from Antonio
Quartulli."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (26 commits)
ipv6: release reference of ip6_null_entry's dst entry in __ip6_del_rt
Remove noisy printks from llcp_sock_connect
tipc: prevent dropped connections due to rcvbuf overflow
silence some noisy printks in irda
team: set qdisc_tx_busylock to avoid LOCKDEP splat
bonding: set qdisc_tx_busylock to avoid LOCKDEP splat
sctp: check src addr when processing SACK to update transport state
sctp: fix a typo in prototype of __sctp_rcv_lookup()
ipv4: add a fib_type to fib_info
can: mpc5xxx_can: fix section type conflict
can: peak_pcmcia: fix error return code
can: peak_pci: fix error return code
cxgb4: Fix build error due to missing linux/vmalloc.h include.
bnx2x: fix ring size for 10G functions
cxgb4: Dynamically allocate memory in t4_memory_rw() and get_vpd_params()
ixgbe: add support for X540-AT1
ixgbe: fix poll loop for FDIRCTRL.INIT_DONE bit
ixgbe: fix PTP ethtool timestamping function
ixgbe: (PTP) Fix PPS interrupt code
ixgbe: Fix PTP X540 SDP alignment code for PPS signal
...
Merge misc patches from Andrew Morton:
"The MM tree is rather stuck while I wait to find out what the heck is
happening with sched/numa. Probably I'll need to route around all the
code which was added to -next, sigh.
So this is "everything else", or at least most of it - other small
bits are still awaiting resolutions of various kinds."
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (180 commits)
lib/decompress.c add __init to decompress_method and data
kernel/resource.c: fix stack overflow in __reserve_region_with_split()
omfs: convert to use beXX_add_cpu()
taskstats: cgroupstats_user_cmd() may leak on error
aoe: update aoe-internal version number to 50
aoe: update documentation to better reflect aoe-plus-udev usage
aoe: remove unused code
aoe: make dynamic block minor numbers the default
aoe: update and specify AoE address guards and error messages
aoe: retain static block device numbers for backwards compatibility
aoe: support more AoE addresses with dynamic block device minor numbers
aoe: update documentation with new URL and VM settings reference
aoe: update copyright year in touched files
aoe: update internal version number to 49
aoe: remove unused code and add cosmetic improvements
aoe: increase net_device reference count while using it
aoe: associate frames with the AoE storage target
aoe: disallow unsupported AoE minor addresses
aoe: do revalidation steps in order
aoe: failover remote interface based on aoe_deadsecs parameter
...
Fix the warning:
WARNING: vmlinux.o(.text+0x14cfd8): Section mismatch in reference from the variable compressed_formats to the function .init.text:gunzip()
The function compressed_formats() references
the function __init gunzip().
etc..
Within decompress.c, compressed_formats[] needs 'a __initdata annotation',
because some of it's data members refer to functions which will be
unloaded after init.
Consequently, its user decompress_method() will get the __init prefix.
Signed-off-by: Hein Tibosch <hein_tibosch@yahoo.es>
Cc: Albin Tonnerre <albin.tonnerre@free-electrons.com>
Cc: Phillip Lougher <phillip@lougher.demon.co.uk>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Using a recursive call add a non-conflicting region in
__reserve_region_with_split() could result in a stack overflow in the case
that the recursive calls are too deep. Convert the recursive calls to an
iterative loop to avoid the problem.
Tested on a machine containing 135 regions. The kernel no longer panicked
with stack overflow.
Also tested with code arbitrarily adding regions with no conflict,
embedding two consecutive conflicts and embedding two non-consecutive
conflicts.
Signed-off-by: T Makphaibulchoke <tmac@hp.com>
Reviewed-by: Ram Pai <linuxram@us.ibm.com>
Cc: Paul Gortmaker <paul.gortmaker@gmail.com>
Cc: Wei Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Convert cpu_to_beXX(beXX_to_cpu(E1) + E2) to use beXX_add_cpu().
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If prepare_reply() succeeds we have allocated memory for 'rep_skb'. If
nla_reserve() then subsequently fails and returns NULL we fail to release
the memory we allocated, thus causing a leak.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Cc: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Because udev use is so widespread, making the old static mapping the
default is too conservative, given the severe limitations it places on
usable AoE addresses. Storage virtualization and larger shelves have made
the old limitations too confining.
These changes make the dynamic block device minor numbers the default,
removing the limitations on usable AoE addresses.
The static arrangement is still available with aoe_dyndevs=0, and the
aoe-stat tool from the userland aoetools package, the user space
counterpart to the aoe driver, recognizes the case where there is a
mismatch between the minor number in sysfs and the minor number in a
special device file.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In general, specific is better when it comes to messages about AoE usage
problems. Also, explicit checks for the AoE broadcast addresses are
added.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The old mapping between AoE target shelf and slot addresses and the block
device minor number is retained as a backwards-compatible feature, with a
new "aoe_dyndevs" module parameter available for enabling dynamic block
device minor numbers.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The ATA over Ethernet protocol uses a major (shelf) and minor (slot)
address to identify a particular storage target. These changes remove an
artificial limitation the aoe driver imposes on the use of AoE addresses.
For example, without these changes, the slot address has a maximum of 15,
but users commonly use slot numbers much greater than that.
The AoE shelf and slot address space is often used sparsely. Instead of
using a static mapping between AoE addresses and the block device minor
number, the block device minor numbers are now allocated on demand.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The old area has a new URL. Also, now that the driver can perform better,
it is worth mentioning the VM settings that help aoe to sink dirty pages
out early, avoiding unecessary memory pressure when much I/O is going on.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The internal version number of the aoe driver appears in a console message
when the driver loads and is usually obtained by the user with the
userland aoe-version tool, part of the aoetools.[1]
Although this patchset includes bugfixes backported from higher-numbered
versions published on the coraid.com website, it is a form of version 49.
1. http://aoetools.sourceforge.net/
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This change removes some unused code and attempts to increase code
consistency.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This change eliminates the danger that the user could rmmod the driver for
a network interface that is being used for AoE by the aoe driver.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In the driver code, "target" and aoetgt refer to a particular remote
interface on the AoE storage target. The latter is identified by its AoE
major and minor addresses. Commands that are being sent to an AoE storage
target {major, minor} can be sent or retransmitted to any of the remote
MAC addresses associated with the AoE storage target.
That is, frames are naturally associated with not an aoetgt (AoE major,
AoE minor, remote MAC address) but an aoedev (AoE major, AoE minor).
Making the code reflect that reality simplifies the driver, especially
when the path to a remote MAC address becomes unusable.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A guard is inserted to prevent AoE minor addresses (slot addresses) higher
than 15 to be used, as they are not yet supported by the driver.
There is a change coming that will allow the aoe driver to overcome this
limit by using system device minor numbers dynamically, but until then,
this guard prevents unexpected targets from being used by the driver when
AoE targets with high minor numbers are on the AoE network.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The discovery process begins with an optional AoE config query command and
an AoE config query response. Normally when an aoe device is already
open, the config query response does not trigger an ATA identify device
command to be sent out, since the response contains storage capacity
information that, if changed, could surprise the user of the device.
The userland "aoe-revalidate" tool uses a character device to trigger an
AoE config query for a particular AoE storage target and an ATA device
identify command, even when the device is open.
This change causes the config query to go out first, reflecting the normal
discovery sequence. The responses could come back in any order, so this
change is fairly cosmetic.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The aoe_deadsecs module parameter allows the user to specify a hard limit
on the number of seconds an AoE command can be retransmitted before the
AoE block device is considered to have failed.
Using aoe_deadsecs to determine the time we try using a different remote
interface helps to ensure that the hard limit is not reached before we've
tried to recover by sending to a different remote port.
As a data storage target, the AoE target is unambiguously identified by
its {major, minor} AoE address tuple, and an AoE target can have multiple
MAC addresses. However, note that "target" in the driver code and
comments means a {major, minor, MAC address} tuple, as in "somewhere to
send packets".
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Users with several network interfaces dedicated to AoE generally do not
configure them to support different-sized AoE data payloads on purpose.
For a given AoE target, there will be a set of local network interfaces
that can reach it. Using only the payload that will fit in the
smallest-sized MTU of all those local interfaces greatly simplifies the
driver, especially in failure scenarios.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The dev_queue_xmit function needs to have interrupts enabled, so the most
simple way to get the locking right but still fulfill that requirement is
to use a process that can call dev_queue_xmit serially over queued
transmissions.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
To allow users to choose an elevator algorithm for their particular
workloads, change from a make_request-style driver to an
I/O-request-queue-handler-style driver.
We have to do a couple of things that might be surprising. We manipulate
the page _count directly on the assumption that we still have no guarantee
that users of the block layer are prohibited from submitting bios
containing pages with zero reference counts.[1] If such a prohibition now
exists, I can get rid of the _count manipulation.
Just as before this patch, we still keep track of the sk_buffs that the
network layer still hasn't finished yet and cap the resources we use with
a "pool" of skbs.[2]
Now that the block layer maintains the disk stats, the aoe driver's
diskstats function can go away.
1. https://lkml.org/lkml/2007/3/1/374
2. https://lkml.org/lkml/2007/7/6/241
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make the frames the aoe driver uses to track the relationship between bios
and packets more flexible and detached, so that they can be passed to an
"aoe_ktio" thread for completion of I/O.
The frames are handled much like skbs, with a capped amount of
preallocation so that real-world use cases are likely to run smoothly and
degenerate gracefully even under memory pressure.
Decoupling I/O completion from the receive path and serializing it in a
process makes it easier to think about the correctness of the locking in
the driver, especially in the case of a remote MAC address becoming
unusable.
[dan.carpenter@oracle.com: cleanup an allocation a bit]
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
tAdd adds the ability to work with large packets composed of a number of
segments, using the scatter gather feature of the block layer (biovecs)
and the network layer (skb frag array). The motivation is the performance
gained by using a packet data payload greater than a page size and by
using the network card's scatter gather feature.
Users of the out-of-tree aoe driver already had these changes, but since
early 2011, they have complained of increased memory utilization and
higher CPU utilization during heavy writes.[1] The commit below appears
related, as it disables scatter gather on non-IP protocols inside the
harmonize_features function, even when the NIC supports sg.
commit f01a5236bd
Author: Jesse Gross <jesse@nicira.com>
Date: Sun Jan 9 06:23:31 2011 +0000
net offloading: Generalize netif_get_vlan_features().
With that regression in place, transmits always linearize sg AoE packets,
but in-kernel users did not have this patch. Before 2.6.38, though, these
changes were working to allow sg to increase performance.
1. http://www.spinics.net/lists/linux-mm/msg15184.html
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add discard support to nbd. If the nbd-server supports discard, it will
send NBD_FLAG_SEND_TRIM to the client. The client will then set the flag
in the kernel via NBD_SET_FLAGS, which tells the kernel to enable discards
for the device (QUEUE_FLAG_DISCARD).
If discard support is enabled, then when the nbd client system receives a
discard request, this will be passed along to the nbd-server. When the
discard request is received by the nbd-server, it will perform:
fallocate(.. FALLOC_FL_PUNCH_HOLE ..)
To punch a hole in the backend storage, which is no longer needed.
Signed-off-by: Paul Clements <paul.clements@steeleye.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a set-flags ioctl, allowing various option flags to be set on an nbd
device. This allows the nbd-client to set the device flags (to enable
read-only mode, or enable discard support, etc.).
Flags are typically specified by the nbd-server. During the negotiation
phase of the nbd connection, the server sends its flags to the client.
The client then uses NBD_SET_FLAGS to inform the kernel of the options.
Also included is a one-line fix to debug output for the set-timeout ioctl.
Signed-off-by: Paul Clements <paul.clements@steeleye.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace the single global destination ID counter with per-net allocation
mechanism to allow independent destID management for each available
RapidIO network. Using bitmap based mechanism instead of counters allows
destination ID release and reuse in systems that support hot-swap.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make RIONET driver multi-net safe/capable by introducing per-net lists of
RapidIO network peers. Rework registration of network adapters to support
all available RIO master port devices.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Modify mport initialization routine to run the RapidIO discovery process
asynchronously. This allows to have an arbitrary order of enumerating and
discovering ports in systems with multiple RapidIO controllers without
creating a deadlock situation if enumerator port is registered after a
discovering one.
Making netID matching to mportID ensures consistent net ID assignment in
multiport RapidIO systems with asynchronous discovery process (global
counter implementation is affected by race between threads).
[akpm@linux-foundation.org: tweak code layput]
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Modify handling of device lists to resolve issues caused by using single
global list of RIO devices during enumeration/discovery. The most common
sign of existing issue is incorrect contents of switch routing tables in
systems with multiple mport controllers while single-port configuration
performs as expected.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The following set of patches provides modifications targeting support of
multiple RapidIO master port (mport) devices on a CPU-side of
RapidIO-capable board. While the RapidIO subsystem code has definitions
suitable for multi-controller/multi-net support, the existing
implementation cannot be considered ready for multiple mport
configurations.
=========== NOTES: =============
a) The patches below do not address RapidIO side view of multiport
processing elements defined in Part 6 of RapidIO spec Rev.2.1 (section
6.4.1). These devices have Base Device ID CSR (0x60) and Component Tag
CSR (0x6C) shared by all SRIO ports. For example, Freescale's P4080,
P3041 and P5020 have a dual-port SRIO controller implemented according
the specification. Enumeration/discovery of such devices from RapidIO
side may require device-specific fixups.
b) Devices referenced above may also require implementation specific
code to setup a host device ID for mport device. These operations are
not addressed by patches in this package.
=================================
Details about provided patches:
1. Fix blocking wait for discovery ready
While it does not happen on PowerPC based platforms, there is
possibility of stalled CPU warning dump on x86 based platforms that run
RapidIO discovery process if they wait too long for being enumerated.
Currently users can avoid it by disabling the soft-lockup detector
using "nosoftlockup" kernel parameter OR by ensuring that enumeration
is completed before soft-lockup is detected.
This patch eliminates blocking wait and keeps a scheduler running.
It also is required for patch 3 below which introduces asynchronous
discovery process.
2. Use device lists handling on per-net basis
This patch allows to correctly support multiple RapidIO nets and
resolves possible issues caused by using single global list of devices
during RapidIO system enumeration/discovery. The most common sign of
existing issue is incorrect contents of switch routing tables in
systems with multiple mport controllers while single-port configuration
performs as expected.
The patch does not eliminate the global RapidIO device list but
changes some routines in enumeration/discovery to use per-net device
lists instead. This way compatibility with upper layer RIO routines is
preserved.
3. Run discovery as an asynchronous process
This patch modifies RapidIO initialization routine to asynchronously
run the discovery process for each corresponding mport. This allows
having an arbitrary order of enumerating and discovering mports without
creating a deadlock situation if an enumerator port was registered
after a discovering one.
On boards with multiple discovering mports it also eliminates order
dependency between mports and may reduce total time of RapidIO
subsystem initialization.
Making netID matching to mportID ensures consistent netID assignment
in multiport RapidIO systems with asynchronous discovery process
(global counter implementation is affected by race between threads).
4. Rework RIONET to support multiple RIO master ports
In the current version of the driver rionet_probe() has comment "XXX
Make multi-net safe". Now it is a good time to address this comment.
This patch makes RIONET driver multi-net safe/capable by introducing
per-net lists of RapidIO network peers. It also enables to register
network adapters for all available mport devices.
5. Add destination ID allocation mechanism
The patch replaces a single global destination ID counter with
per-net allocation mechanism to allow independent destID management for
each available RapidIO network. Using bitmap based mechanism instead
of counters allows destination ID release and reuse in systems that
support hot-swap.
This patch:
Fix blocking wait loop in the RapidIO discovery routine to avoid warning
dumps about stalled CPU on x86 platforms.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Apply port RX/TX enable operations only to active switch ports.
RapidIO specification (Part 6: LP-Serial Physical Layer) recommends to
keep Output Port Enable (TX) and Input Port Enable (RX) control bits in
disabled state (0b0) after device reset. It also allows to have
implementation specific reset state for these bits.
This patch ensures that TX/RX enable action is applied only to active
switch's ports while preserving an initial state of inactive ones.
This patch is intended to keep inactive switch ports with inbound and
outbound packet transfers disabled to block unexpected packets during hot
insertion event. While it does not fix any visible malfunction it is
intended to prevent such events in future.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add Tsi721 routines to support RapidIO subsystem's inbound memory mapping
interface (RapidIO to system's local memory).
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add common inbound memory mapping/unmapping interface. This allows to make
local memory space accessible from the RapidIO side using hardware mapping
capabilities of RapidIO bridging devices. The new interface is intended to
enable data transfers between RapidIO devices in combination with DMA engine
support.
This patch is based on patch submitted by Li Yang <leoli@freescale.com>
(https://lists.ozlabs.org/pipermail/linuxppc-dev/2009-April/071210.html)
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
