We can't look up the address of the entry point of the function simply
via that function symbol for all architectures.
For PPC64 ABI, actually there is a function descriptors structure.
A function descriptor is a three doubleword data structure that contains
the following values:
* The first doubleword contains the address of the entry point of
the function.
* The second doubleword contains the TOC base address for
the function.
* The third doubleword contains the environment pointer for
languages such as Pascal and PL/1.
So we should call a wapperred dereference_function_descriptor() to get
the address of the entry point of the function.
Note this is also safe for other architecture after refer to
"include/asm-generic/sections.h" since:
dereference_function_descriptor(p) always is (p) if without arched definition.
Signed-off-by: Tiejun Chen <tiejun.chen@windriver.com>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
When locally adding in some additional kdb commands, I stumbled
across an issue with the dynamic expansion of the kdb command table.
When the number of kdb commands exceeds the size of the statically
allocated kdb_base_commands[] array, additional space is allocated in
the kdb_register_repeat() routine.
The unused portion of the newly allocated array was not being initialized
to zero properly and this would result in segfaults when help '?' was
executed or when a search for a non-existing command would traverse the
command table beyond the end of valid command entries and then attempt
to use the non-zeroed area as actual command entries.
Signed-off-by: John Blackwood <john.blackwood@ccur.com>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Pull input subsystem fixes from Dmitry Torokhov:
"Two small driver fixups and a documentation update for managed input
devices"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: wacom - fix wacom_set_report retry logic
Input: document that unregistering managed devices is not necessary
Input: lm8323 - fix checking PWM interrupt status
Commit c060f943d0 ("mm: use aligned zone start for pfn_to_bitidx
calculation") fixed out calculation of the index into the pageblock
bitmap when a !SPARSEMEM zome was not aligned to pageblock_nr_pages.
However, the _allocation_ of that bitmap had never taken this alignment
requirement into accout, so depending on the exact size and alignment of
the zone, the use of that index could then access past the allocation,
resulting in some very subtle memory corruption.
This was reported (and bisected) by Ingo Molnar: one of his random
config builds would hang with certain very specific kernel command line
options.
In the meantime, commit c060f943d0 has been marked for stable, so this
fix needs to be back-ported to the stable kernels that backported the
commit to use the right alignment.
Bisected-and-tested-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Mel Gorman <mgorman@suse.de>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
with older hypervisor stacks, such as Xen 4.1.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)
iQEcBAABAgAGBQJRHZ7eAAoJEFjIrFwIi8fJZ+sH/ieMkzdBB6aqbFMcNr7mkfBo
i3swjO2JQI7REYIHfKEVoR3IgHfqKEuABdeEQrceE0XqDepFh84YiKGI2QpPRWEA
903vUV4DXVdcBrypbL45tSFZ1Jxsrzx+F7WfV/f9WHyeiwOyaZTGVQH0VuOzpcum
RvPTT7MmC7g8MJDi66SDYBaX/pBQzifQ81nMWWjXNw0w4CwWX7le1cScZEP42MR6
jTEHzYMLDojdO+2aQM5pt/0CGI5tzBHtX5nNRl6tovlPI3ckknYYx6a7RfxkfZzF
IkMIuGS32yLfsswPPIiMs47/Qgiq3BN6eSTJXMZKUwQokL9yEs8LodcnRDYfgyQ=
=fqcJ
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.8-rc7-tag-two' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull xen fixes from Konrad Rzeszutek Wilk:
"Two fixes:
- A simple bug-fix for redundant NULL check.
- CVE-2013-0228/XSA-42: x86/xen: don't assume %ds is usable in
xen_iret for 32-bit PVOPS
and two reverts:
- Revert the PVonHVM kexec. The patch introduces a regression with
older hypervisor stacks, such as Xen 4.1."
* tag 'stable/for-linus-3.8-rc7-tag-two' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
Revert "xen PVonHVM: use E820_Reserved area for shared_info"
Revert "xen/PVonHVM: fix compile warning in init_hvm_pv_info"
xen: remove redundant NULL check before unregister_and_remove_pcpu().
x86/xen: don't assume %ds is usable in xen_iret for 32-bit PVOPS.
As reported by Klaus Schmidinger:
"In VDR I use an ioctl() call with FE_READ_UNCORRECTED_BLOCKS on a
device (using stb0899). After this call I check 'errno' for
EOPNOTSUPP to determine whether this device supports this call. This
used to work just fine, until a few months ago I noticed that my
devices using stb0899 didn't display their signal quality in VDR's OSD
any more. After further investigation I found that
ioctl(FE_READ_UNCORRECTED_BLOCKS) no longer returns EOPNOTSUPP, but
rather ENOTTY. And since I stop getting the signal quality in case
any unknown errno value appears, this broke my signal quality query
function."
While the changes reflect what is there at:
http://comments.gmane.org/gmane.linux.kernel/1235728
it does cause regression on userspace. So, revert it to stop the
damage.
This reverts commit 177ffe506c ("[media] dvb_frontend: return -ENOTTY
for unimplement IOCTL").
Reported-by: Klaus Schmidinger <Klaus.Schmidinger@tvdr.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull sparc fixes from David Miller:
"A couple small fixes for sparc including some THP brown-paper-bag
material:
1) During the merging of all the THP support for various
architectures, sparc missed adding a
HAVE_ARCH_TRANSPARENT_HUGEPAGE to it's Kconfig, oops.
2) Sparc needs to be mindful of hugepages in get_user_pages_fast().
3) Fix memory leak in SBUS probe, from Cong Ding.
4) The sunvdc virtual disk client driver has a test of the bitmask of
vdisk server supported operations which was off by one bit"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sunvdc: Fix off-by-one in generic_request().
sparc64: Fix get_user_pages_fast() wrt. THP.
sparc64: Add missing HAVE_ARCH_TRANSPARENT_HUGEPAGE.
sparc: kernel/sbus.c: fix memory leakage
Pull one more x86 fix from Peter Anvin:
"Sigh. One more patch in the "please don't brick my Samsung" series"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi: Clear EFI_RUNTIME_SERVICES rather than EFI_BOOT by "noefi" boot parameter
Hotplug
PCI/PM: Clean up PME state when removing a device
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=zdXb
-----END PGP SIGNATURE-----
Merge tag '3.8-pci-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fix from Bjorn Helgaas:
"This is another fix for v3.8. It fixes an oops that happens when a
Thunderbolt adapter is unplugged (remove device, poll for PME events
on no-longer-existing device, oops)."
* tag '3.8-pci-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI/PM: Clean up PME state when removing a device
omapdss)
* fix DPI displays on OMAP3630 (OMAPDSS: add FEAT_DPI_USES_VDDS_DSI to
omap3630_dss_feat_list)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=eJF5
-----END PGP SIGNATURE-----
Merge tag 'omapdss-for-3.8-rc8' of git://gitorious.org/linux-omap-dss2/linux
Pull omapdss fixes from Tomi Valkeinen:
"It'd be great if these two late fixes would still make it into 3.8.
The other one fixes ARM kernel compilation when using 'allyesconfig',
and the other makes DPI displays function again on OMAP3630 boards:
- Fix ARM compilation with "allyesconfig" (omapdrm: fix the
dependency to omapdss)
- fix DPI displays on OMAP3630 (OMAPDSS: add FEAT_DPI_USES_VDDS_DSI
to omap3630_dss_feat_list)"
* tag 'omapdss-for-3.8-rc8' of git://gitorious.org/linux-omap-dss2/linux:
omapdrm: fix the dependency to omapdss
OMAPDSS: add FEAT_DPI_USES_VDDS_DSI to omap3630_dss_feat_list
Pull i2c maintainer info update from Wolfram Sang:
"Since my old email and repos are not working anymore, and this already
caused some confusion, I think a MAINTAINERS update for 3.8 is
helpful. So, people trying I2C with the new kernel can properly reach
me and find my repos."
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
MAINTAINERS: change my email and repos
This reverts commit 9d02b43dee.
We are doing this b/c on 32-bit PVonHVM with older hypervisors
(Xen 4.1) it ends up bothing up the start_info. This is bad b/c
we use it for the time keeping, and the timekeeping code loops
forever - as the version field never changes. Olaf says to
revert it, so lets do that.
Acked-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
The 'operations' bitmap corresponds one-for-one with the operation
codes, no adjustment is necessary.
Reported-by: Mark Kettenis <mark.kettenis@xs4all.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
omapdrm uses "select" in Kconfig to enable omapdss. This doesn't work
correctly, as "select" forces omapdss to be enabled in the config even
if it normally could not be enabled because of missing Kconfig
dependencies.
This causes a build break on ARM, when using allyesconfig:
drivers/video/omap2/dss/dss.c: In function 'dss_calc_clock_div':
drivers/video/omap2/dss/dss.c:572:20: error: 'CONFIG_OMAP2_DSS_MIN_FCK_PER_PCK' undeclared (first use in this function)
drivers/video/omap2/dss/dss.c:572:20: note: each undeclared identifier is reported only once for each function it appears in
Instead of using select, this patch changes omapdrm to use "depend
on".
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
commit 195e672a76
OMAPDSS: DPI: Remove cpu_is_xxxx checks
made the mistake of assuming that cpu_is_omap34xx() is exclusive of
other cpu_is_* predicates whereas it includes cpu_is_omap3630().
So on an omap3630, code that was previously enabled by
if (cpu_is_omap34xx())
is now disabled as
dss_has_feature(FEAT_DPI_USES_VDDS_DSI)
fails.
So add FEAT_DPI_USES_VDDS_DSI to omap3630_dss_feat_list.
Cc: Chandrabhanu Mahapatra <cmahapatra@ti.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
There was a serious problem in samsung-laptop that its platform driver is
designed to run under BIOS and running under EFI can cause the machine to
become bricked or can cause Machine Check Exceptions.
Discussion about this problem:
https://bugs.launchpad.net/ubuntu-cdimage/+bug/1040557https://bugzilla.kernel.org/show_bug.cgi?id=47121
The patches to fix this problem:
efi: Make 'efi_enabled' a function to query EFI facilities
83e6818974
samsung-laptop: Disable on EFI hardware
e0094244e4
Unfortunately this problem comes back again if users specify "noefi" option.
This parameter clears EFI_BOOT and that driver continues to run even if running
under EFI. Refer to the document, this parameter should clear
EFI_RUNTIME_SERVICES instead.
Documentation/kernel-parameters.txt:
===============================================================================
...
noefi [X86] Disable EFI runtime services support.
...
===============================================================================
Documentation/x86/x86_64/uefi.txt:
===============================================================================
...
- If some or all EFI runtime services don't work, you can try following
kernel command line parameters to turn off some or all EFI runtime
services.
noefi turn off all EFI runtime services
...
===============================================================================
Signed-off-by: Satoru Takeuchi <takeuchi_satoru@jp.fujitsu.com>
Link: http://lkml.kernel.org/r/511C2C04.2070108@jp.fujitsu.com
Cc: Matt Fleming <matt.fleming@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
unregister_and_remove_pcpu on a NULL pointer is a no-op, so the NULL check in
sync_pcpu can be removed.
Signed-off-by: Cyril Roelandt <tipecaml@gmail.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
This fixes CVE-2013-0228 / XSA-42
Drew Jones while working on CVE-2013-0190 found that that unprivileged guest user
in 32bit PV guest can use to crash the > guest with the panic like this:
-------------
general protection fault: 0000 [#1] SMP
last sysfs file: /sys/devices/vbd-51712/block/xvda/dev
Modules linked in: sunrpc ipt_REJECT nf_conntrack_ipv4 nf_defrag_ipv4
iptable_filter ip_tables ip6t_REJECT nf_conntrack_ipv6 nf_defrag_ipv6
xt_state nf_conntrack ip6table_filter ip6_tables ipv6 xen_netfront ext4
mbcache jbd2 xen_blkfront dm_mirror dm_region_hash dm_log dm_mod [last
unloaded: scsi_wait_scan]
Pid: 1250, comm: r Not tainted 2.6.32-356.el6.i686 #1
EIP: 0061:[<c0407462>] EFLAGS: 00010086 CPU: 0
EIP is at xen_iret+0x12/0x2b
EAX: eb8d0000 EBX: 00000001 ECX: 08049860 EDX: 00000010
ESI: 00000000 EDI: 003d0f00 EBP: b77f8388 ESP: eb8d1fe0
DS: 0000 ES: 007b FS: 0000 GS: 00e0 SS: 0069
Process r (pid: 1250, ti=eb8d0000 task=c2953550 task.ti=eb8d0000)
Stack:
00000000 0027f416 00000073 00000206 b77f8364 0000007b 00000000 00000000
Call Trace:
Code: c3 8b 44 24 18 81 4c 24 38 00 02 00 00 8d 64 24 30 e9 03 00 00 00
8d 76 00 f7 44 24 08 00 00 02 80 75 33 50 b8 00 e0 ff ff 21 e0 <8b> 40
10 8b 04 85 a0 f6 ab c0 8b 80 0c b0 b3 c0 f6 44 24 0d 02
EIP: [<c0407462>] xen_iret+0x12/0x2b SS:ESP 0069:eb8d1fe0
general protection fault: 0000 [#2]
---[ end trace ab0d29a492dcd330 ]---
Kernel panic - not syncing: Fatal exception
Pid: 1250, comm: r Tainted: G D ---------------
2.6.32-356.el6.i686 #1
Call Trace:
[<c08476df>] ? panic+0x6e/0x122
[<c084b63c>] ? oops_end+0xbc/0xd0
[<c084b260>] ? do_general_protection+0x0/0x210
[<c084a9b7>] ? error_code+0x73/
-------------
Petr says: "
I've analysed the bug and I think that xen_iret() cannot cope with
mangled DS, in this case zeroed out (null selector/descriptor) by either
xen_failsafe_callback() or RESTORE_REGS because the corresponding LDT
entry was invalidated by the reproducer. "
Jan took a look at the preliminary patch and came up a fix that solves
this problem:
"This code gets called after all registers other than those handled by
IRET got already restored, hence a null selector in %ds or a non-null
one that got loaded from a code or read-only data descriptor would
cause a kernel mode fault (with the potential of crashing the kernel
as a whole, if panic_on_oops is set)."
The way to fix this is to realize that the we can only relay on the
registers that IRET restores. The two that are guaranteed are the
%cs and %ss as they are always fixed GDT selectors. Also they are
inaccessible from user mode - so they cannot be altered. This is
the approach taken in this patch.
Another alternative option suggested by Jan would be to relay on
the subtle realization that using the %ebp or %esp relative references uses
the %ss segment. In which case we could switch from using %eax to %ebp and
would not need the %ss over-rides. That would also require one extra
instruction to compensate for the one place where the register is used
as scaled index. However Andrew pointed out that is too subtle and if
further work was to be done in this code-path it could escape folks attention
and lead to accidents.
Reviewed-by: Petr Matousek <pmatouse@redhat.com>
Reported-by: Petr Matousek <pmatouse@redhat.com>
Reviewed-by: Andrew Cooper <andrew.cooper3@citrix.com>
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Mostly mirrors the s390 logic, as unlike x86 we don't need the
SetPageReferenced() bits.
On sparc64 we also lack a user/privileged bit in the huge PMDs.
In order to make this work for THP and non-THP builds, some header
file adjustments were necessary. Namely, provide the PMD_HUGE_* bit
defines and the pmd_large() inline unconditionally rather than
protected by TRANSPARENT_HUGEPAGE.
Reported-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This got missed in the cleanups done for the S390 THP
support.
CC: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"This is primarily to get those r8169 reverts sorted, but other fixes
have accumulated meanwhile.
1) Revert two r8169 changes to fix suspend/resume for some users,
from Francois Romieu.
2) PCI dma mapping errors in atl1c are not checked for and this cause
hard crashes for some users, from Xiong Huang.
3) In 3.8.x we merged the removal of the EXPERIMENTAL dependency for
'dlm' but the same patch for 'sctp' got lost somewhere, resulting
in the potential for build errors since there are cross
dependencies. From Kees Cook.
4) SCTP's ipv6 socket route validation makes boolean tests
incorrectly, fix from Daniel Borkmann.
5) mac80211 does sizeof(ptr) instead of (sizeof(ptr) * nelem), from
Cong Ding.
6) arp_rcv() can crash on shared non-linear packets, from Eric
Dumazet.
7) Avoid crashes in macvtap by setting ->gso_type consistently in
ixgbe, qlcnic, and bnx2x drivers. From Michael S Tsirkin and
Alexander Duyck.
8) Trinity fuzzer spots infinite loop in __skb_recv_datagram(), fix
from Eric Dumazet.
9) STP protocol frames should use high packet priority, otherwise an
overloaded bridge can get stuck. From Stephen Hemminger.
10) The HTB packet scheduler was converted some time ago to store
internal timestamps in nanoseconds, but we don't convert back into
psched ticks for the user during dumps. Fix from Jiri Pirko.
11) mwl8k channel table doesn't set the .band field properly,
resulting in NULL pointer derefs. Fix from Jonas Gorski.
12) mac80211 doesn't accumulate channels properly during a scan so we
can downgrade heavily to a much less desirable connection speed.
Fix from Johannes Berg.
13) PHY probe failure in stmmac can result in resource leaks and
double MDIO registery later, from Giuseppe CAVALLARO.
14) Correct ipv6 checksumming in ip6t_NPT netfilter module, also fix
address prefix mangling, from YOSHIFUJI Hideaki."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (27 commits)
net, sctp: remove CONFIG_EXPERIMENTAL
net: sctp: sctp_v6_get_dst: fix boolean test in dst cache
batman-adv: Fix NULL pointer dereference in DAT hash collision avoidance
net/macb: fix race with RX interrupt while doing NAPI
atl1c: add error checking for pci_map_single functions
htb: fix values in opt dump
ixgbe: Only set gso_type to SKB_GSO_TCPV4 as RSC does not support IPv6
net: fix infinite loop in __skb_recv_datagram()
net: qmi_wwan: add Yota / Megafon M100-1 4g modem
mwl8k: fix band for supported channels
bridge: set priority of STP packets
mac80211: fix channel selection bug
arp: fix possible crash in arp_rcv()
bnx2x: set gso_type
qlcnic: set gso_type
ixgbe: fix gso type
stmmac: mdio register has to fail if the phy is not found
stmmac: fix macro used for debugging the xmit
Revert "r8169: enable internal ASPM and clock request settings".
Revert "r8169: enable ALDPS for power saving".
...
Pull x86 fixes from Peter Anvin:
"One (hopefully) last batch of x86 fixes. You asked for the patch by
patch justifications, so here they are:
x86, MCE: Retract most UAPI exports
This one unexports from userspace a bunch of definitions which should
never have been exported. We really don't want to create an
accidental legacy here.
x86, doc: Add a bootloader ID for OVMF
This is a documentation-only patch, just recording the official
assignment of a boot loader ID.
x86: Do not leak kernel page mapping locations
Security: avoid making it needlessly easy for user space to probe the
kernel memory layout.
x86/mm: Check if PUD is large when validating a kernel address
Prevent failures using /proc/kcore when using 1G pages.
x86/apic: Work around boot failure on HP ProLiant DL980 G7 Server systems
Works around a BIOS problem causing boot failures on affected hardware."
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm: Check if PUD is large when validating a kernel address
x86/apic: Work around boot failure on HP ProLiant DL980 G7 Server systems
x86, doc: Add a bootloader ID for OVMF
x86: Do not leak kernel page mapping locations
x86, MCE: Retract most UAPI exports
Change to my private email, change to my shiny new kernel.org repos,
and drop outdated entry from the former maintainer. Drop my PCA entry,
too, since it belongs to the I2C realm anyhow.
Signed-off-by: Wolfram Sang <wolfram@the-dreams.de>
Devices are added to pci_pme_list when drivers use pci_enable_wake()
or pci_wake_from_d3(), but they aren't removed from the list unless
the driver explicitly disables wakeup. Many drivers never disable
wakeup, so their devices remain on the list even after they are
removed, e.g., via hotplug. A subsequent PME poll will oops when
it tries to touch the device.
This patch disables PME# on a device before removing it, which removes
the device from pci_pme_list. This is safe even if the device never
had PME# enabled.
This oops can be triggered by unplugging a Thunderbolt ethernet adapter
on a Macbook Pro, as reported by Daniel below.
[bhelgaas: changelog]
Reference: http://lkml.kernel.org/r/CAMVG2svG21yiM1wkH4_2pen2n+cr2-Zv7TbH3Gj+8MwevZjDbw@mail.gmail.com
Reported-and-tested-by: Daniel J Blueman <daniel@quora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org
This config item has not carried much meaning for a while now and is
almost always enabled by default. As agreed during the Linux kernel
summit, remove it.
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Acked-by: Steven Whitehouse <swhiteho@redhat.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We walk through the bind address list and try to get the best source
address for a given destination. However, currently, we take the
'continue' path of the loop when an entry is invalid (!laddr->valid)
*and* the entry state does not equal SCTP_ADDR_SRC (laddr->state !=
SCTP_ADDR_SRC).
Thus, still, invalid entries with SCTP_ADDR_SRC might not 'continue'
as well as valid entries with SCTP_ADDR_{NEW, SRC, DEL}, with a possible
false baddr and matchlen as a result, causing in worst case dst route
to be false or possibly NULL.
This test should actually be a '||' instead of '&&'. But lets fix it
and make this a bit easier to read by having the condition the same way
as similarly done in sctp_v4_get_dst.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An entry in DAT with the hashed position of 0 can cause a NULL pointer
dereference when the first entry is checked by batadv_choose_next_candidate.
This first candidate automatically has the max value of 0 and the max_orig_node
of NULL. Not checking max_orig_node for NULL in batadv_is_orig_node_eligible
will lead to a NULL pointer dereference when checking for the lowest address.
This problem was added in 785ea11441
("batman-adv: Distributed ARP Table - create DHT helper functions").
Signed-off-by: Pau Koning <paukoning@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When interrupts are disabled, an RX condition can occur but
it is not reported when enabling interrupts again. We need to check
RSR and use napi_reschedule() if condition is met.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A user reported the following oops when a backup process reads
/proc/kcore:
BUG: unable to handle kernel paging request at ffffbb00ff33b000
IP: [<ffffffff8103157e>] kern_addr_valid+0xbe/0x110
[...]
Call Trace:
[<ffffffff811b8aaa>] read_kcore+0x17a/0x370
[<ffffffff811ad847>] proc_reg_read+0x77/0xc0
[<ffffffff81151687>] vfs_read+0xc7/0x130
[<ffffffff811517f3>] sys_read+0x53/0xa0
[<ffffffff81449692>] system_call_fastpath+0x16/0x1b
Investigation determined that the bug triggered when reading
system RAM at the 4G mark. On this system, that was the first
address using 1G pages for the virt->phys direct mapping so the
PUD is pointing to a physical address, not a PMD page.
The problem is that the page table walker in kern_addr_valid() is
not checking pud_large() and treats the physical address as if
it was a PMD. If it happens to look like pmd_none then it'll
silently fail, probably returning zeros instead of real data. If
the data happens to look like a present PMD though, it will be
walked resulting in the oops above.
This patch adds the necessary pud_large() check.
Unfortunately the problem was not readily reproducible and now
they are running the backup program without accessing
/proc/kcore so the patch has not been validated but I think it
makes sense.
Signed-off-by: Mel Gorman <mgorman@suse.de>
Reviewed-by: Rik van Riel <riel@redhat.coM>
Reviewed-by: Michal Hocko <mhocko@suse.cz>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: stable@vger.kernel.org
Cc: linux-mm@kvack.org
Link: http://lkml.kernel.org/r/20130211145236.GX21389@suse.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull hp parisc automounter fix from Helge Deller:
"This unbreaks automounter support for the parisc architecture (and
probably aarch64 as well).""
* 'autofs-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
unbreak automounter support on 64-bit kernel with 32-bit userspace (v2)
Pull s390 regression fix from Martin Schwidefsky:
"The recent fix for the s390 sched_clock() function uncovered yet
another bug in s390_next_ktime which causes an endless loop in KVM.
This regression should be fixed before v3.8.
I keep the fingers crossed that this is the last one for v3.8."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/timer: avoid overflow when programming clock comparator
Pull m68knommu fix from Greg Ungerer:
"This contains a single critical fix for the non-MMU m68k platforms.
The change of the kernel exec code path has revealed a problem in the
start thread code that causes crashing on boot. This is the fix for
it."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68knommu: fix trap on execing /bin/init
in htb_change_class() cl->buffer and cl->buffer are stored in ns.
So in dump, convert them back to psched ticks.
Note this was introduced by:
commit 56b765b79e
htb: improved accuracy at high rates
Please consider this for -net/-stable.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull tile bugfixes from Chris Metcalf:
"This includes a variety of minor bug fixes, mostly to do with testing
"make allyesconfig", "make allmodconfig", "make allnoconfig", inspired
to Tejun Heo's observation about Kconfig.freezer not being included.
The largest changes are just syntax changes removing the tile-specific
use of a macro named INT_MASK, which is way too commonly redefined
throughout driver code"
* 'stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
tile: tag some code with #ifdef CONFIG_COMPAT
tile: fix memcpy_*io functions for allnoconfig
tile: export a handful of symbols appropriately
drm: fix compile failure by including <linux/swiotlb.h>
tile: avoid defining INT_MASK macro in <arch/interrupts.h>
tile: provide "screen_info" when enabling VT
drivers/input/joystick/analog.c: enable precise timer
tile: include kernel/Kconfig.freezer in tile Kconfig
tile: remove an unused variable in copy_thread()
We had a number of fixes queued up, but taking a strict pass-through
and weeding out any that either have been broken for a while, or are
for platforms that need out-of-tree code to be useful anyway, or other
fixes for problems that few users are likely to see in real life, only
this short branch of patches remains.
The three patches here are to make SMP boot work on the Calxeda
platforms again. Some of the rework for cpuids on 3.8 broke it (and it
was discovered late, unfortunately).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=tsdi
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc into akpm
Pull ARM SoC fixes from Olof Johansson:
"We had a number of fixes queued up, but taking a strict pass-through
and weeding out any that either have been broken for a while, or are
for platforms that need out-of-tree code to be useful anyway, or other
fixes for problems that few users are likely to see in real life, only
this short branch of patches remains.
The three patches here are to make SMP boot work on the Calxeda
platforms again. Some of the rework for cpuids on 3.8 broke it (and
it was discovered late, unfortunately)."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: highbank: mask cluster id from cpu_logical_map
ARM: scu: mask cluster id from cpu_logical_map
ARM: scu: add empty scu_enable for !CONFIG_SMP
The total number of low memory pages is determined as totalram_pages -
totalhigh_pages, so without this patch all CMA pageblocks placed in
highmem were accounted to low memory.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Minchan Kim <minchan.kim@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We're forgetting to reenable local interrupts on an error path.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Reported-by: Josh Boyer <jwboyer@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The designed workflow for the caches in kmemcg is: register it with
memcg_register_cache() if kmemcg is already available or later on when a
new kmemcg appears at memcg_update_cache_sizes() which will handle all
caches in the system. The caches created at boot time will be handled
by the later, and the memcg-caches as well as any system caches that are
registered later on by the former.
There is a bug, however, in memcg_register_cache: we correctly set up
the array size, but do not mark the cache as a root cache.
This means that allocations for any cache appearing late in the game
will see memcg->memcg_params->is_root_cache == false, and in particular,
trigger VM_BUG_ON(!cachep->memcg_params->is_root_cache) in
__memcg_kmem_cache_get.
The obvious fix is to include the missing assignment.
Signed-off-by: Glauber Costa <glommer@parallels.com>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With commit 8e72033f2a ("thp: make MADV_HUGEPAGE check for
mm->def_flags") the VM_NOHUGEPAGE flag may be set on s390 in
mm->def_flags for certain processes, to prevent future thp mappings.
This would be overwritten by do_mlockall(), which sets it back to 0 with
an optional VM_LOCKED flag set.
To fix this, instead of overwriting mm->def_flags in do_mlockall(), only
the VM_LOCKED flag should be set or cleared.
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Reported-by: Vivek Goyal <vgoyal@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit e7e034e18a ("drivers/rtc/rtc-pl031.c: fix the missing operation
on enable") accidentally broke the ST variants of PL031.
The bit that is being poked as "clockwatch" enable bit for the ST
variants does the work of bit 0 on this variant. Bit 0 is used for a
clock divider on the ST variants, and setting it to 1 will affect
timekeeping in a very bad way.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Mian Yousaf KAUKAB <mian.yousaf.kaukab@stericsson.com>
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
John W. Linville says:
====================
Here is another handful of late-breaking fixes intended for the 3.8
stream... Hopefully the will still make it! :-)
There are three mac80211 fixes pulled from Johannes:
"Here are three fixes still for the 3.8 stream, the fix from Cong Ding
for the bad sizeof (Stephen Hemminger had pointed it out before but I'd
promptly forgotten), a mac80211 managed-mode channel context usage fix
where a downgrade would never stop until reaching non-HT and a bug in
the channel determination that could cause invalid channels like HT40+
on channel 11 to be used."
Also included is a mwl8k fix that avoids an oops when using mwl8k
devices that only support the 5 GHz band.
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The original fix that was applied for setting gso_type required more change
than necessary because it was assumed ixgbe does RSC on IPv6 frames and this
is not correct. RSC is only supported with IPv4/TCP frames only. As such we
can simplify the fix and avoid the unnecessary move of eth_type_trans.
The previous patch "ixgbe: fix gso type" and this patch reduce the entire fix
to one line that sets gso_type to TCPV4 if the frame is RSC.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tommi was fuzzing with trinity and reported the following problem :
commit 3f518bf745 (datagram: Add offset argument to __skb_recv_datagram)
missed that a raw socket receive queue can contain skbs with no payload.
We can loop in __skb_recv_datagram() with MSG_PEEK mode, because
wait_for_packet() is not prepared to skip these skbs.
[ 83.541011] INFO: rcu_sched detected stalls on CPUs/tasks: {}
(detected by 0, t=26002 jiffies, g=27673, c=27672, q=75)
[ 83.541011] INFO: Stall ended before state dump start
[ 108.067010] BUG: soft lockup - CPU#0 stuck for 22s! [trinity-child31:2847]
...
[ 108.067010] Call Trace:
[ 108.067010] [<ffffffff818cc103>] __skb_recv_datagram+0x1a3/0x3b0
[ 108.067010] [<ffffffff818cc33d>] skb_recv_datagram+0x2d/0x30
[ 108.067010] [<ffffffff819ed43d>] rawv6_recvmsg+0xad/0x240
[ 108.067010] [<ffffffff818c4b04>] sock_common_recvmsg+0x34/0x50
[ 108.067010] [<ffffffff818bc8ec>] sock_recvmsg+0xbc/0xf0
[ 108.067010] [<ffffffff818bf31e>] sys_recvfrom+0xde/0x150
[ 108.067010] [<ffffffff81ca4329>] system_call_fastpath+0x16/0x1b
Reported-by: Tommi Rantala <tt.rantala@gmail.com>
Tested-by: Tommi Rantala <tt.rantala@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Pavel Emelyanov <xemul@parallels.com>
Acked-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull drm fixes from Dave Airlie:
"Three nouveau fixes, all user visible issues, and one radeon
regression fix"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon: enforce use of radeon_get_ib_value when reading user cmd
drm/nouveau: add lockdep annotations
drm/nv50/fb: Fix nullptr-deref on IGPs
drm/nouveau: use different register to wait for secret scrubber
