Make sure that code match exactly what comment says about pre 1.2
bluetooth version. Since this is HCI detail lmp_ver changed to hci_ver.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Use bluetooth names instead of BT SIG assigned numbers
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Check for hci_ver instead of lmp_ver
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
The current default watchdog timer is enabled, but we are seeing issues on
legacy devices. So change the default setting of watchdog timer to per
device based. But user still can use the "wd_disable" module parameter
to overwrite the system setting
Cc: stable@vger.kernel.org #3.0+
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Group keys in IBSS or AP mode are not programmed
into the device since we give the key to it with
every TX packet. However, we do need mac80211 to
create the MMIC & PN in all cases. Move the code
around to set the key flags all the time. We set
them even when the key is removed again but that
is obviously harmless.
Cc: stable@vger.kernel.org
Reported-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove old code not touched for several years.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patch adds the parameter struct and the command complete event
handler to the LE Set Scan Parameter HCI command.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patch adds the dev_flags field to struct hci_dev. This new
flags variable should be used to define flags related to BR/EDR
and/or LE controller itself. It should be used to define flags
which represents states from the controller. The dev_flags is
cleared in case the controller sends a Reset Command Complete
Event to the host.
Also, this patch adds the HCI_LE_SCAN flag which was created to
track if the controller is performing LE scan or not. The flag
is set/cleared when the controller starts/stops scanning.
This is an initial effort to stop using hdev->flags to define
internal flags since it is exported to userspace by an ioctl.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Upstream Code Aurora function with minor trivial fixes.
Origin: git://codeaurora.org/kernel/msm.git
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
The blkcipher must be freed to avoid memory leak.
Signed-off-by: Brian Gix <bgix@codeaurora.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Some MITM scenarios require handling of the User Passkey Request event,
by querying the user, and passing the response back.
Signed-off-by: Brian Gix <bgix@codeaurora.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
For some MITM protection pairing scenarios, the user is
required to enter or accept a 6 digit passkey.
Signed-off-by: Brian Gix <bgix@codeaurora.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
the default tx/rx chainmask for AR9462 is 0x3.
this patch helps to assign 0x3 rather than 0x7 for
AR9462 with the help of fix_chainmask module if something
goes wrong in reading tx/rx chain mask from OTP/EEPROM
card(though its very unlikely)
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
only for AR9485 (or) later chipsets TxIQ calibration
runs as part of AGC calibration. without this patch
TX IQ cal completion i.e. ar9003_hw_tx_iq_cal_run won't be executed
for AR9003
Reviewed-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is not used outside this driver so no need to make the symbol global.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We should free "bus_if" here, it's a small leak but it makes the static
checkers happy.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
here we check for BT state and if BT calibration has started,
give 25ms for BT Calibration to finish. we also take care of 2G/5G
switch and LNA transfer incase WLAN is operating in 5G. in case the BT
state is awake when we do WLAN calibration re-calibrate and we reset
the message exchange between WLAN and BT. BT is given preference when
simultaneous CAL request happens. calibration for WLAN/BT is done
assuming that the other co-existing module is in awake state, if not
we continue to do calibration while if the other module's state changes
we need to do restart the calibration handshake
Cc: Wilson Tsao <wtsao@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
WLAN communicates with BT for its calibration by sending WLAN_CAL_REQ,
waits for BT_CAL_GRANT. This is done with the help of GPM messages.
also WLAN_CAL_DONE messages is sent once WLAN calibration is done.
Cc: Wilson Tsao <wtsao@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
send halt BT GPM if the chip is in network sleep and BT state
is awake
Cc: Wilson Tsao <wtsao@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
required buffers and dma allocation is done for GPM and SCHED
messages
Cc: Wilson Tsao <wtsao@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
check for the condition of MCI interrupt being triggered and
appropriately obtain the values of MCI_INTERRUPT_RX_MSG_RAW and
MCI_INTERRUPT_RAW
Cc: Wilson Tsao <wtsao@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
MCI interrupt is an asynchronous one, so take care of it by having a
check in ath9k_hw_intrpend, which actually decides whether the interrupt
is really for the driver from ath_isr
Cc: Wilson Tsao <wtsao@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
enable MCI interrupt when ath9k_hw_enable_interrupts is called,
like during the completion of chip_reset before which the interrupts
are disabled
Cc: Wilson Tsao <wtsao@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
these parameter will be utilized and modified in the MCI hardware codes
state machine
Cc: Wilson Tsao <wtsao@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
these definitions will be used by MCI state machine and the corresponding
hardware code
Cc: Wilson Tsao <wtsao@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Logging messages that mimic function tracer enter/exit
aren't necessary. Just remove them.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All uses have been removed, so killing what's not necessary.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using the standard debugging mechanisms is better than
subsystem specific ones when the subsystem doesn't use
a specific struct.
Coalesce long formats.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using the normal logging styles is preferred over
subsystem specific styles when the subsystem does
not take a specific struct.
Convert nfc_<level> specific messages to pr_<level>
Add newlines to uses.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As of hostap_0_7_1~358 the CONFIG_DRIVER_PRISM54
was removed from upstream wpa_supplicant/hostapd so
lets just kill the useless old prism54 private ioctl
crap.
Cc: Jouni Malinen <j@w1.fi>
Cc: David Miller <davem@davemloft.net>
Reported-by: David Miller <davem@davemloft.net>
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
change the AR_DEF_ANTENNA register settings i.e setting default antenna
setting only for antenna diversity enabled chipsets. no point in
doing this for MIMO chipsets
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
GPIO pin 4 is assigned AR9462 chipsets LED.
while GPIO pin 0 worked for obselete AR9462 chipsets though
they are meant for EEPROM as per Russell
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: Russell Hu <rhu@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The on-channel work optimisations have caused a
number of issues, and the code is unfortunately
very complex and almost impossible to follow.
Instead of attempting to put in more workarounds
let's just remove those optimisations, we can
work on them again later, after we change the
whole auth/assoc design.
This should fix rate_control_send_low() warnings,
see RH bug 731365.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
