platform_get_irq() returns a negative number on failure, so adjust the
logic to detect such condition and propagate the real error value on
failure.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Ley Foon Tan <lftan@altera.com>
PCI_EXP_CAP is an iProc-specific value, so rename it to IPROC_PCI_EXP_CAP
to make it obvious that it's not related to the generic values like
PCI_EXP_RTCTL, etc. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
During soft reset (e.g., "reboot" from Linux) on some iProc-based SOCs, the
LCPLL clock and PERST both go off simultaneously. This seems in accordance
with the PCIe Card Electromechanical spec, r2.0, sec 2.2.3, which says the
clock goes inactive after PERST# goes active, but doesn't specify how long
the clock should be valid after PERST#.
However, we have observed that with the iProc Stingray, some Intel NVMe
endpoints, e.g., the P3700 400GB series, are not detected correctly upon
the next boot sequence unless the clock remains valid for some time after
PERST# is asserted.
Delay 500ms after asserting PERST# before performing a reboot. The 500ms
is experimentally determined.
Signed-off-by: Oza Pawandeep <oza.oza@broadcom.com>
[bhelgaas: changelog, add spec reference, fold in iproc_pcie_shutdown()
export from Arnd Bergmann <arnd@arndb.de>]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
VMD hardware has to share its vectors among child devices in its PCI
domain so we should allocate as many as possible rather than just ones
that can be affinitized.
pci_alloc_irq_vectors_affinity() limits the number of affinitized IRQs to
the number of present CPUs (see irq_calc_affinity_vectors()). But we'd
prefer to have more vectors, even if they aren't distributed across the
CPUs, so use pci_alloc_irq_vectors() instead.
Reported-by: Brad Goodman <Bradley.Goodman@dell.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
[bhelgaas: add irq_calc_affinity_vectors() reference to changelog]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Switch from using custom INTX_NUM macro to the generic PCI_NUM_INTX definition
for the number of INTx interrupts.
Signed-off-by: Honghui Zhang <honghui.zhang@mediatek.com>
[bhelgaas: use subject/changelog from similar patches]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
MT2712 and MT7622's PCIe host controller support MSI, but only 32-bit MSI
addresses are supported. It connects to GIC with the same IRQ number as the
INTx IRQ, so it shares the same IRQ with INTx IRQ.
Add MSI support for MT2712 and MT7622.
Signed-off-by: Honghui Zhang <honghui.zhang@mediatek.com>
[bhelgaas: changes to follow rcar & tegra: rename to mtk_pcie_msi_alloc(),
add mtk_pcie_msi_free(), free hwirq if irq_create_mapping() fails, call
irq_dispose_mapping() from mtk_msi_teardown_irq()]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Ryder Lee <ryder.lee@mediatek.com>
75983c6d1f38 ("PCI: mediatek: Add controller support for MT2712 and
MT7622") has put the mtk_pcie * into bus->sysdata. Take advantage of that
to get the private data and simplify the code.
Signed-off-by: Honghui Zhang <honghui.zhang@mediatek.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Ryder Lee <ryder.lee@mediatek.com>
MT2712 and MT7622 using a new IP block of Gen2 controller which has two
root ports and shares the same probing flow with MT2701/MT7623.
Both MT2712 and MT7622 have the same per-port control registers, but
there are slight differences between them:
- MT7622 has more clocks than MT2712.
- MT7622 has shared control registers which are used to enable LTSSM and
ASPM while MT2712 does not.
Add host controller support for MT2712/MT7622.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Honghui Zhang <honghui.zhang@mediatek.com>
[bhelgaas: folded in fix from http://lkml.kernel.org/r/1502715868-17651-2-git-send-email-honghui.zhang@mediatek.com]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This is a transitional patch. We currently use platfarm_get_resource() for
retrieving the IOMEM resources, but there might be some chips don't have
subsys/shared registers part, which depends on platform design, and these
will be introduced in further patches.
Switch this function to use the platform_get_resource_byname() so that the
binding can be agnostic of the resource order.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Honghui Zhang <honghui.zhang@mediatek.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Introduce a structure "mtk_pcie_soc" to abstract the differences between
controller generations, and the .startup() hook is used to encapsulate some
SoC-dependent related setting. In doing so, the common code which will be
reused by future chips.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Honghui Zhang <honghui.zhang@mediatek.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Rename "port->index" to "port->slot" since the ports are hardwired at
PCI_SLOT. Also rename "mtk_pcie_parse_ports()" to "mtk_pcie_parse_port()"
since it parses one port each time.
No functional change in this patch.
Signed-off-by: Honghui Zhang <honghui.zhang@mediatek.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Wait for Gen2 training with readl_poll_timeout(), and simplify the hardware
assert logical by merging it into a new mtk_pcie_startup_port() interface.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Honghui Zhang <honghui.zhang@mediatek.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Commit a53e35db70 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls to
explicitly state whether the driver needs exclusive or shared reset control
behavior. Convert all drivers requesting exclusive resets to the explicit
API call so the temporary transition helpers can be removed.
No functional changes.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Ryder Lee <ryder.lee@mediatek.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Call pci_unmap_iospace() to clean up if probe fails.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Call irq_domain_remove() to clean up if probe fails.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
We observed that the clk_pciephy_ref is still enabled when we fail to probe
the driver.
root@linaro-alip:~# grep pcie /sys/kernel/debug/clk/clk_summary
clk_pciephy_ref 1 1 24000000 0 0
clk_pcie_pm 0 0 24000000 0 0
clk_pcie_core_cru 0 0 125000000 0 0
clk_pciephy_ref100m 0 0 100000000 0 0
aclk_pcie 0 0 148500000 0 0
aclk_perf_pcie 0 0 148500000 0 0
pclk_pcie 0 0 37125000 0 0
clk_pcie_core 0 0 0 0 0
clk_pciephy_ref is used by the PHY driver and we need to properly disable
it for this case. Add error handling in rockchip_pcie_init_port() and
rockchip_pcie_resume_noirq() to fix this issue.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Factor out rockchip_pcie_deinit_phys() so it can be reused by
rockchip_pcie_suspend_noirq() and rockchip_pcie_remove(). No functional
change intended.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Factor out rockchip_pcie_disable_clocks() so it can be reused by other
functions.
No functional change intended, but it does change the order of unpreparing
clocks in the rockchip_pcie_resume_noirq() error path so it matches the
other paths.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Factor out rockchip_pcie_enable_clocks() so it can be reused by
rockchip_pcie_resume_noirq() and rockchip_pcie_probe().
No functional change intended, but it does change the order of unpreparing
clocks in the rockchip_pcie_resume_noirq() error path.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Factor out rockchip_pcie_setup_irq() to prepare for future bug fixes. No
functional change intended.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The reset GPIO can be connected to a I2C or SPI IO expander, which may
sleep, so it is safer to use the gpiod_set_value_cansleep() variant
instead.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Shawn Lin <shawn.lin@rock-chips.com>
Use the PCI_NUM_INTX macro to indicate the number of PCI INTx interrupts
rather than the magic number 4. This makes it clearer where the number
comes from & what it relates to.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Shawn Lin <shawn.lin@rock-chips.com>
Commit a53e35db70 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls to
explicitly state whether the driver needs exclusive or shared reset control
behavior. Convert all drivers requesting exclusive resets to the explicit
API call so the temporary transition helpers can be removed.
No functional changes.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Shawn Lin <shawn.lin@rock-chips.com>
Configuration Request Retry Status ("CRS") completions are a required part
of PCIe. A PCIe device may respond to config a request with a CRS
completion to indicate that it needs more time to initialize. A Root Port
that receives a CRS completion may automatically retry the request, or it
may treat the request as a failed transaction. For a failed read, it will
likely synthesize all 1's data, i.e., 0xffffffff, to complete the read to
the CPU.
CRS Software Visibility ("CRS SV") is an optional feature. Per PCIe r3.1,
sec 2.3.2, if supported and enabled, a Root Port that receives a CRS
completion for a config read of the Vendor ID will synthesize 0x0001 data
(an invalid Vendor ID) instead of retrying or failing the transaction. The
0x0001 data makes the CRS completion visible to software, so it can perform
other tasks while waiting for the device.
The iProc "Stingray" PCIe controller does not support CRS completions
correctly. From the Stingray PCIe Controller spec:
4.7.3.3. Retry Status On Configuration Cycle
Endpoints are allowed to generate retry status on configuration cycles.
In this case, the RC needs to re-issue the request. The IP does not
handle this because the number of configuration cycles needed will
probably be less than the total number of non-posted operations needed.
When a retry status is received on the User RX interface for a
configuration request that was sent on the User TX interface, it will be
indicated with a completion with the CMPL_STATUS field set to 2=CRS, and
the user will have to find the address and data values and send a new
transaction on the User TX interface. When the internal configuration
space returns a retry status during a configuration cycle (user_cscfg =
1) on the Command/Status interface, the pcie_cscrs will assert with the
pcie_csack signal to indicate the CRS status.
When the CRS Software Visibility Enable register in the Root Control
register is enabled, the IP will return the data value to 0x0001 for the
Vendor ID value and 0xffff (all 1’s) for the rest of the data in the
request for reads of offset 0 that return with CRS status. This is true
for both the User RX Interface and for the Command/Status interface.
When CRS Software Visibility is enabled, the CMPL_STATUS field of the
completion on the User RX Interface will not be 2=CRS and the pcie_cscrs
signal will not assert on the Command/Status interface.
The Stingray hardware never reissues configuration requests when it
receives CRS completions. Contrary to what sec 4.7.3.3 above says, when it
receives a CRS completion, it synthesizes 0xffff0001 data regardless of the
address of the read or the value of the CRS SV enable bit.
This is broken in two ways:
1) When CRS SV is disabled, the Root Port should never synthesize the
0x0001 value. If it receives a CRS completion, it should fail the
transaction and synthesize all 1's data.
2) When CRS SV is enabled, the Root Port should only synthesize 0x0001
data if it receives a CRS completion for a read of the Vendor ID. If it
receives a CRS completion for any other read, it should fail the
transaction and synthesize all 1's data.
This breaks pci_flr_wait(), which reads the Command register and expects to
see all 1's data if the read fails because of CRS completions. On
Stingray, it sees the incorrect 0xffff0001 data instead.
It also breaks config registers that contain the 0xffff0001 value. If we
read such a register, software can't distinguish a CRS completion from the
actual value read from the device.
On Stingray, if we read 0xffff0001 data, assume this indicates a CRS
completion and retry the read for 500ms. If we time out, return all 1's
(0xffffffff) data. Note that this corrupts registers that happen to
contain 0xffff0001.
Stingray advertises CRS SV support in its Root Capabilities register, and
the CRS SV enable bit is writable (even though the hardware ignores it).
Mask out PCI_EXP_RTCAP_CRSVIS so software doesn't try to use CRS SV.
Signed-off-by: Oza Pawandeep <oza.oza@broadcom.com>
[bhelgaas: changelog, add probe-time warning about corruption, don't
advertise CRS SV support, remove duplicate pci_generic_config_read32(),
fix alignment based on patch from Arnd Bergmann <arnd@arndb.de>]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Factor out the address calculation for memory-mapped config accesses as a
separate function. No functional change intended.
Signed-off-by: Oza Pawandeep <oza.oza@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Check the status of all lanes and idle the inactive one(s).
Tested-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
[bhelgaas: always set lanes_map, even for legacy_phy case]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
We distinguish the legacy PHY from newer per-lane PHYs by adding legacy_phy
flag. Note that the legacy PHY is still the first option to be searched in
order not to break the backward compatibility of DTB.
Tested-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
[bhelgaas: tidy rockchip_pcie_get_phys()]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Now that we have a custom printf format specifier, convert users of
full_name() to use %pOF instead. This is preparation for removing storing
of the full path string for each node.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Allow the xilinx-pcie driver to be built on MIPS platforms which make use
of generic PCI drivers rather than legacy MIPS-specific interfaces. This
is used on the MIPS Boston development board.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Bharat Kumar Gogada <bharatku@xilinx.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Ravikiran Gummaluri <rgummal@xilinx.com>
The Xilinx AXI bridge for PCI Express device provides interrupts indicating
the completion of config space accesses. We have previously
enabled/unmasked them but do nothing with them besides acknowledge them.
Leave the interrupts masked in order to avoid servicing a large number of
pointless interrupts during boot.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Bharat Kumar Gogada <bharatku@xilinx.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Ravikiran Gummaluri <rgummal@xilinx.com>
The INTx & MSI interrupt decode paths duplicated a fair bit of common
functionality. They also strictly handled interrupts in order of INTx then
MSI, so if both types of interrupt were to be asserted simultaneously and
the MSI interrupt were first in the FIFO then the INTx code would read it &
ignore it before the MSI code then had to read it again, wasting the
original FIFO read.
Unify the INTx & MSI decode in order to reduce that duplication & allow a
single FIFO read to be performed for each interrupt regardless of its type.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Bharat Kumar Gogada <bharatku@xilinx.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Ravikiran Gummaluri <rgummal@xilinx.com>
The devicetree binding documentation for the Xilinx NWL PCIe root port
bridge shows an example which uses an interrupt-map property to map PCI
INTx interrupts to hardware IRQ numbers 1-4. The driver creates an IRQ
domain with size 4, which therefore covers the hwirq range 0-3.
This means that if we attempt to make use of the INTD interrupt then we're
likely to hit a WARN() in irq_domain_associate() because INTD, or hwirw=4,
is outside of the range covered by the IRQ domain. irq_domain_associate()
will then return -EINVAL and we'll be unable to make use of INTD.
Fix this by making use of the pci_irqd_intx_xlate() helper function to
translate the 1-4 range used in the DT to a 0-3 range used within the
driver, and stop adding 1 to decoded hwirq numbers.
Whilst cleaning up INTx handling we make use of the new PCI_NUM_INTX macro
& drop the custom INTX definitions.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: "Sören Brinkmann" <soren.brinkmann@xilinx.com>
The pcie-xilinx driver creates an IRQ domain of size 4 for legacy PCI INTx
interrupts, which at first glance seems reasonable since there are 4
possible such interrupts. Unfortunately the driver then proceeds to use the
range 1-4 as the hwirq numbers for INTA-INTD, causing warnings & broken
interrupts when attempting to use INTD/hwirq=4 due to it being beyond the
range of the IRQ domain:
WARNING: CPU: 0 PID: 1 at kernel/irq/irqdomain.c:365
irq_domain_associate+0x170/0x220
error: hwirq 0x4 is too large for dummy
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Tainted: G W
4.12.0-rc5-00126-g19e1b3a10aad-dirty #427
Stack : 0000000000000000 0000000000000004 0000000000000006 ffffffff8092c78a
0000000000000061 ffffffff8018bf60 0000000000000000 0000000000000000
ffffffff8088c287 ffffffff80811d18 a8000000ffc60000 ffffffff80926678
0000000000000001 0000000000000000 ffffffff80887880 ffffffff80960000
ffffffff80920000 ffffffff801e6744 ffffffff80887880 a8000000ffc4f8f8
000000000000089c ffffffff8018d260 0000000000010000 ffffffff80811d18
0000000000000000 0000000000000001 0000000000000000 0000000000000000
0000000000000000 a8000000ffc4f840 0000000000000000 ffffffff8042cf34
0000000000000000 0000000000000000 0000000000000000 0000000000040c00
0000000000000000 ffffffff8010d1c8 0000000000000000 ffffffff8042cf34
...
Call Trace:
[<ffffffff8010d1c8>] show_stack+0x80/0xa0
[<ffffffff8042cf34>] dump_stack+0xd4/0x110
[<ffffffff8013ea98>] __warn+0xf0/0x108
[<ffffffff8013eb14>] warn_slowpath_fmt+0x3c/0x48
[<ffffffff80196528>] irq_domain_associate+0x170/0x220
[<ffffffff80196bf0>] irq_create_mapping+0x88/0x118
[<ffffffff801976a8>] irq_create_fwspec_mapping+0xb8/0x320
[<ffffffff80197970>] irq_create_of_mapping+0x60/0x70
[<ffffffff805d1318>] of_irq_parse_and_map_pci+0x20/0x38
[<ffffffff8049c210>] pci_fixup_irqs+0x60/0xe0
[<ffffffff8049cd64>] xilinx_pcie_probe+0x28c/0x478
[<ffffffff804e8ca8>] platform_drv_probe+0x50/0xd0
[<ffffffff804e73a4>] driver_probe_device+0x2c4/0x3a0
[<ffffffff804e7544>] __driver_attach+0xc4/0xd0
[<ffffffff804e5254>] bus_for_each_dev+0x64/0xa8
[<ffffffff804e5e40>] bus_add_driver+0x1f0/0x268
[<ffffffff804e8000>] driver_register+0x68/0x118
[<ffffffff801001a4>] do_one_initcall+0x4c/0x178
[<ffffffff808d3ca8>] kernel_init_freeable+0x204/0x2b0
[<ffffffff80730b68>] kernel_init+0x10/0xf8
[<ffffffff80106218>] ret_from_kernel_thread+0x14/0x1c
Fix this by making use of the new pci_irqd_intx_xlate() helper to translate
the INTx 1-4 range into the 0-3 range suitable for the IRQ domain of size
4, and stop adding 1 to the hwirq number decoded from the interrupt FIFO
which is already in the range 0-3.
Whilst we're here we switch to using PCI_NUM_INTX rather than the magic
number 4, making it clearer what the 4 means.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Bharat Kumar Gogada <bharatku@xilinx.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Ravikiran Gummaluri <rgummal@xilinx.com>
We plan to introduce per-lane PHYs, so factor out rockchip_pcie_get_phys()
to make it easier in the future. No functional change intended.
Tested-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Get vpcie12v from DT and control it if available.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Use the PCI_NUM_INTX macro to indicate the number of PCI INTx interrupts
rather than the magic number 4. This makes it clearer where the number
comes from & what it relates to.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
of_irq_get() may return a negative error number as well as 0 on failure,
while the driver only checks for 0, blithely continuing with the call to
irq_set_chained_handler_and_data() -- that function expects *unsigned int*
so should probably do nothing when a large IRQ number resulting from a
conversion of a negative error number is passed to it. The driver then
probes successfully while being only partly functional...
Check for 'irq <= 0' instead and propagate the negative error number to the
probe method -- that will allow the deferred probing as well.
Fixes: d3c68e0a7e ("PCI: faraday: Add Faraday Technology FTPCI100 PCI Host Bridge driver")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
The devicetree binding documentation for the Altera PCIe controller shows
an example which uses an interrupt-map property to map PCI INTx interrupts
to hardware IRQ numbers 1-4. The driver creates an IRQ domain with size 5
in order to cover this range, with hwirq=0 left unused.
This patch cleans up this wasted IRQ domain entry, modifying the driver to
use an IRQ domain of size 4 which matches the actual number of PCI INTx
interrupts. Since the hwirq numbers 1-4 are part of the devicetree binding,
and this is considered ABI, we cannot simply change the interrupt-map
property to use the range 0-3. Instead we make use of the
pci_irqd_intx_xlate() helper function to translate the range 1-4 used at
the DT level into the range 0-3 which is now used within the driver, and
stop adding 1 to decoded hwirq numbers in altera_pcie_isr().
Whilst cleaning up INTx handling we make use of the new PCI_NUM_INTX macro
& drop the custom INTX_NUM definition.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Ley Foon Tan <lftan@altera.com>
The local variable "num_of_vectors" was unused, so remove it.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Ley Foon Tan <lftan@altera.com>
Switch from using a custom LEGACY_IRQ_NUM macro to the generic PCI_NUM_INTX
definition for the number of INTx interrupts.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
When no PCIe card is inserted, there is a memory leak as
pci_free_resource_list() is not called before returning.
Signed-off-by: Harunobu Kurokawa <harunobu.kurokawa.dn@renesas.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Commit 90634e8540 ("PCI: rcar: Convert PCI scan API to
pci_scan_root_bus_bridge()") converted PCI root bus scan API to the new
pci_scan_root_bus_bridge() API; in the process some error paths were not
updated correctly which may cause memory leaks.
Fix the driver error exit path reinstating the previous correct
error exit behaviour.
Fixes: 90634e8540 ("PCI: rcar: Convert PCI scan API to pci_scan_root_bus_bridge()")
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Harunobu Kurokawa <harunobu.kurokawa.dn@renesas.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Free up the IRQs we request on the suspend path and reallocate them on the
resume path.
Fixes this error:
CPU 111 disable failed: CPU has 9 vectors assigned and there are only 0 available.
Error taking CPU111 down: -34
Non-boot CPUs are not disabled
Enabling non-boot CPUs ...
Signed-off-by: Scott Bauer <scott.bauer@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Keith Busch <keith.busch@intel.com>
To support implementing remote TLB flushing on Hyper-V with a hypercall
we need to make vp_index available outside of vmbus module. Rename and
globalize.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Stephen Hemminger <sthemmin@microsoft.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Jork Loeser <Jork.Loeser@microsoft.com>
Cc: K. Y. Srinivasan <kys@microsoft.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Simon Xiao <sixiao@microsoft.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: devel@linuxdriverproject.org
Link: http://lkml.kernel.org/r/20170802160921.21791-7-vkuznets@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The setup of MSI with Hyper-V host was sleeping with locks held. This
error is reported when doing SR-IOV hotplug with kernel built with lockdep:
BUG: sleeping function called from invalid context at kernel/sched/completion.c:93
in_atomic(): 1, irqs_disabled(): 1, pid: 1405, name: ip
3 locks held by ip/1405:
#0: (rtnl_mutex){+.+.+.}, at: [<ffffffff976b10bb>] rtnetlink_rcv+0x1b/0x40
#1: (&desc->request_mutex){+.+...}, at: [<ffffffff970ddd33>] __setup_irq+0xb3/0x720
#2: (&irq_desc_lock_class){-.-...}, at: [<ffffffff970ddd65>] __setup_irq+0xe5/0x720
irq event stamp: 3476
hardirqs last enabled at (3475): [<ffffffff971b3005>] get_page_from_freelist+0x225/0xc90
hardirqs last disabled at (3476): [<ffffffff978024e7>] _raw_spin_lock_irqsave+0x27/0x90
softirqs last enabled at (2446): [<ffffffffc05ef0b0>] ixgbevf_configure+0x380/0x7c0 [ixgbevf]
softirqs last disabled at (2444): [<ffffffffc05ef08d>] ixgbevf_configure+0x35d/0x7c0 [ixgbevf]
The workaround is to poll for host response instead of blocking on
completion.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
We don't want slower IRQ handlers impacting faster devices that happen to
be assigned the same VMD interrupt vector. The driver was trying to
separate such devices by checking if MSI-X wasn't used, but really we just
don't want endpoint devices to share with bridges. Most bridges may use MSI
currently, so that criteria happened to work, but newer ones may use MSI-X,
so this patch explicitly checks the device type when choosing a vector.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The driver has a special purpose for the VMD device's first IRQ, so this
one shouldn't be considered for IRQ affinity.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Commit a53e35db70 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls to
explicitly state whether the driver needs exclusive or shared reset control
behavior. Convert all drivers requesting exclusive resets to the explicit
API call so the temporary transition helpers can be removed.
No functional changes.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
The gpiod API checks for NULL descriptors, so there is no need to duplicate
the check in the driver.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com
The local variable "pcie" was unused, so remove it.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Ray Jui <rjui@broadcom.com>
pci_scan_root_bus_bridge() returns zero for success, or a negative errno.
A typo in ae13cb9b19 ("PCI: rockchip: Convert PCI scan API to
pci_scan_root_bus_bridge()") treated zero as a failure.
Fix the typo.
Fixes: ae13cb9b19 ("PCI: rockchip: Convert PCI scan API to pci_scan_root_bus_bridge()")
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
This driver is required to work around several hardware bugs in the PCIe
controller.
The SMP8759 does not support legacy interrupts or IO space.
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
[bhelgaas: add CONFIG_BROKEN dependency, various cleanups]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
* pci/host-rockchip:
PCI: rockchip: Use normal register bank for config accessors
PCI: rockchip: Use local struct device pointer consistently
PCI: rockchip: Check for clk_prepare_enable() errors during resume
MAINTAINERS: Remove Wenrui Li as Rockchip PCIe driver maintainer
PCI: rockchip: Configure RC's MPS setting
PCI: rockchip: Reconfigure configuration space header type
PCI: rockchip: Split out rockchip_pcie_cfg_configuration_accesses()
PCI: rockchip: Move configuration accesses into rockchip_pcie_cfg_atu()
PCI: rockchip: Rename rockchip_cfg_atu() to rockchip_pcie_cfg_atu()
PCI: rockchip: Control vpcie0v9 for system PM
Rockchip's RC has two banks of registers for the root port: a normal bank
that is strictly compatible with the PCIe spec, and a privileged bank that
can be used to change RO bits of root port registers.
When probing the RC driver, we use the privileged bank to do some basic
setup work as some RO bits are hw-inited to wrong value. But we didn't
change to the normal bank after probing the driver.
This leads to a serious problem when the PME code tries to clear the PME
status by writing PCI_EXP_RTSTA_PME to the register of PCI_EXP_RTSTA. Per
PCIe 3.0 spec, section 7.8.14, the PME status bit is RW1C. So the PME code
is doing the right thing to clear the PME status but we find the RC doesn't
clear it but actually setting it to one. So finally the system trap in
pcie_pme_work_fn() as PCI_EXP_RTSTA_PME is true now forever. This issue
can be reproduced by booting kernel with pci=nomsi.
Use the normal register bank for the PCI config accessors. The privileged
bank is used only internally by this driver.
Fixes: e77f847d ("PCI: rockchip: Add Rockchip PCIe controller support")
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
Cc: Jeffy Chen <jeffy.chen@rock-chips.com>
Cc: Brian Norris <briannorris@chromium.org>
* pci/host-hv:
PCI: hv: Use vPCI protocol version 1.2
PCI: hv: Add vPCI version protocol negotiation
PCI: hv: Temporary own CPU-number-to-vCPU-number infra
PCI: hv: Use page allocation for hbus structure
PCI: hv: Fix comment formatting and use proper integer fields
of_device_ids are not supposed to change at runtime. All functions working
with of_device_ids provided by <linux/of.h> work with const of_device_ids.
So mark the non-const structs as const.
File size before:
text data bss dec hex filename
195 600 0 795 31b drivers/pci/host/pcie-xilinx.o
File size after constify xilinx_pcie_of_match:
text data bss dec hex filename
595 184 0 779 30b drivers/pci/host/pcie-xilinx.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
- Add spinlock for protecting legacy mask register
- Few wifi end points which only support legacy interrupts, performs
hardware reset functionalities after disabling interrupts by invoking
disable_irq() and then re-enable using enable_irq(), they enable hardware
interrupts first and then virtual IRQ line later.
- The legacy IRQ line goes low only after DEASSERT_INTx is received. As
the legacy IRQ line is high immediately after hardware interrupts are
enabled but virq of EP is still in disabled state and EP handler is never
executed resulting no DEASSERT_INTx. If dummy IRQ chip is used,
interrupts are not masked and system hangs with CPU stall.
- Add IRQ chip functions instead of dummy IRQ chip for legacy interrupts.
- Legacy interrupts are level sensitive, so using handle_level_irq() is
more appropriate as it is masks interrupts until Endpoint handles
interrupts and unmasks interrupts after Endpoint handler is executed.
- Legacy interrupts are level triggered, virtual IRQ line of EndPoint shows
as edge in /proc/interrupts.
- Set IRQ flags of virtual IRQ line of EP to level triggered at the time of
mapping.
Signed-off-by: Bharat Kumar Gogada <bharatku@xilinx.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Recent __call_srcu() changes have exposed that we need to cleanup SRCU
structures after pci_stop_root_bus() calls into vmd_msi_free().
Fixes: 3906b91844 ("PCI: vmd: Use SRCU as a local RCU to prevent delaying global RCU")
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Keith Busch <keith.busch@intel.com>
Cc: <stable@vger.kernel.org> # 4.11
VMD domains are allocated starting at 0x10000, not 0x1000 as the comment
said. Correct the comment and add a reference to the ACPI spec for _SEG.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Use a local "struct device *dev" for brevity and consistency with other
drivers. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The PCI host bridge found on Tegra SoCs doesn't require the MSI target
address to be backed by physical system memory. Writes are intercepted
within the controller and never make it to the memory pointed to.
Since no actual system memory is required, remove the allocation of a
single page and hardcode the MSI target address with a special address that
maps to the last 4 KiB page within the range that is reserved for system
memory and memory-mapped I/O in the FPCI address map.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
The MSI target address can reside beyond the 32-bit boundary on devices
with more than 2 GiB of system memory. The PCI host bridge on Tegra can
easily support 64-bit addresses, so make sure to pass the upper 32 bits of
the target address to endpoints when allocating MSI entries.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
We have a local "struct device *dev" in rockchip_pcie_probe(). Use it
consistently throughout the function. No functional change intended.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
clk_prepare_enable() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Shawn Lin <shawn.lin@rock-chips.com>
The default value of MPS for RC is 128 bytes, but actually it could support
256 bytes. So this patch fixes this issue.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Per PCIe base specification (Revision 3.1a), section 7.5.3, type 1
configuration space header should be used when accessing PCIe switch. So
we need to reconfigure the header according to the bus number we are
accessing. Otherwise we could not visit the buses behind the switch.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
We need to reconfigure the header type later, so split out a new function.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Configuration accesses is also part of ATU settings, so let's keep all of
them inside rockchip_pcie_cfg_atu().
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Rename rockchip_cfg_atu() to keep the name consistent with other functions
in pcie-rockchip.c.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
vpcie0v9 is used for PHY, so we could disable it as we don't need PHY to
work then in S3 if folks assign it DT. But we should note that there is a
side effect that we could not support beacon wakeup if we disable vpcie0v9
for aggressive power-saving.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Brian Norris <briannorris@chromium.org>
Cc: Jeffy Chen <jeffy.chen@rock-chips.com>
of_device_ids are not supposed to change at runtime. All functions working
with of_device_ids provided by <linux/of.h> work with const of_device_ids.
So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Update the Hyper-V vPCI driver to use the Server-2016 version of the vPCI
protocol, fixing MSI creation and retargeting issues.
Signed-off-by: Jork Loeser <jloeser@microsoft.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Acked-by: K. Y. Srinivasan <kys@microsoft.com>
Hyper-V vPCI offers different protocol versions. Add the infra for
negotiating the one to use.
Signed-off-by: Jork Loeser <jloeser@microsoft.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Acked-by: K. Y. Srinivasan <kys@microsoft.com>
To ease parallel effort to centralize CPU-number-to-vCPU-number conversion,
temporarily stand up own version, file-local hv_tmp_cpu_nr_to_vp_nr().
Once the changes have merged, this work-around can be removed, and the
calls replaced with hv_cpu_number_to_vp_number().
Signed-off-by: Jork Loeser <jloeser@microsoft.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Acked-by: K. Y. Srinivasan <kys@microsoft.com>
The hv_pcibus_device structure contains an in-memory hypercall argument
that must not cross a page boundary. Allocate the structure as a page to
ensure that.
Signed-off-by: Jork Loeser <jloeser@microsoft.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Acked-by: K. Y. Srinivasan <kys@microsoft.com>
Fix comment formatting and use proper integer fields.
Signed-off-by: Jork Loeser <jloeser@microsoft.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Acked-by: K. Y. Srinivasan <kys@microsoft.com>
Similar as commit 8ff0ef996c ("PCI: host: Mark PCIe/PCI (MSI) IRQ cascade
handlers as IRQF_NO_THREAD"), we should mark PCIe/PCI (MSI) IRQ cascade
handlers in designware, qcom, and vmd as IRQF_NO_THREAD explicitly.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com> # vmd
Acked-by: Jingoo Han <jingoohan1@gmail.com> # pcie-designware-plat.c
struct pci_host_bridge gained hooks to map/swizzle IRQs, so that the IRQ
mapping can be done automatically by PCI core code through the
pci_assign_irq() function instead of resorting to arch-specific
implementation callbacks to carry out the same task which force PCI host
bridge drivers implementation to implement per-arch kludges to carry out a
task that is inherently architecture agnostic.
Add map/swizzle IRQs hooks to the xilinx-nwl PCI host driver to move the
IRQ allocation into core code and stop relying on arch-specific callbacks.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Bharat Kumar Gogada <bharat.kumar.gogada@xilinx.com>
struct pci_host_bridge gained hooks to map/swizzle IRQs, so that the IRQ
mapping can be done automatically by PCI core code through the
pci_assign_irq() function instead of resorting to arch-specific
implementation callbacks to carry out the same task which force PCI host
bridge drivers implementation to implement per-arch kludges to carry out a
task that is inherently architecture agnostic.
Add map/swizzle IRQs hooks to the rockchip PCI host driver to move the IRQ
allocation into core code and stop relying on arch-specific callbacks.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Wenrui Li <wenrui.li@rock-chips.com>
Cc: Shawn Lin <shawn.lin@rock-chips.com>
struct pci_host_bridge gained hooks to map/swizzle IRQs, so that the IRQ
mapping can be done automatically by PCI core code through the
pci_assign_irq() function instead of resorting to arch-specific
implementation callbacks to carry out the same task which force PCI host
bridge drivers implementation to implement per-arch kludges to carry out a
task that is inherently architecture agnostic.
Add map/swizzle IRQs hooks to the xgene PCI host driver to move the IRQ
allocation into core code and stop relying on arch-specific callbacks.
Tested-by: Khuong Dinh <kdinh@apm.com> # with e1000e
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Tanmay Inamdar <tinamdar@apm.com>
Since, through struct pci_host_bridge.map/swizzle_irq hooks, IRQs are now
allocated in the pci_assign_irq() callback automatically, PCI host bridge
drivers can stop relying on pci_fixup_irqs() for IRQ allocation.
Drop pci_fixup_irqs() usage from PCI altera host bridge driver.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Ley Foon Tan <lftan@altera.com>
Since, through struct pci_host_bridge.map/swizzle_irq hooks, IRQs are now
allocated in the pci_assign_irq() callback automatically, PCI host bridge
drivers can stop relying on pci_fixup_irqs() for IRQ allocation.
Drop pci_fixup_irqs() usage from PCI versatile host bridge driver.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
[bhelgaas: folded in typo fix from Arnd Bergmann <arnd@arndb.de>:
http://lkml.kernel.org/r/20170621215323.3921382-4-arnd@arndb.de]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Rob Herring <robh@kernel.org>
Since, through struct pci_host_bridge.map/swizzle_irq hooks, IRQs are now
allocated in the pci_assign_irq() callback automatically, PCI host bridge
drivers can stop relying on pci_fixup_irqs() for IRQ allocation.
Drop pci_fixup_irqs() usage from PCI host-common bridge driver.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Since, through struct pci_host_bridge.map/swizzle_irq hooks, IRQs are now
allocated in the pci_assign_irq() callback automatically, PCI host bridge
drivers can stop relying on pci_fixup_irqs() for IRQ allocation.
Drop pci_fixup_irqs() usage from PCI ftpci100 host bridge driver.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Since, through struct pci_host_bridge.map/swizzle_irq hooks, IRQs are now
allocated in the pci_assign_irq() callback automatically, PCI host bridge
drivers can stop relying on pci_fixup_irqs() for IRQ allocation.
Drop pci_fixup_irqs() usage from PCI iproc host bridge driver.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Jon Mason <jonmason@broadcom.com>
Since, through struct pci_host_bridge.map/swizzle_irq hooks, IRQs are now
allocated in the pci_assign_irq() callback automatically, PCI host bridge
drivers can stop relying on pci_fixup_irqs() for IRQ allocation.
Drop pci_fixup_irqs() usage from PCI rcar host bridge driver.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Simon Horman <horms@verge.net.au>
Since, through struct pci_host_bridge.map/swizzle_irq hooks, IRQs are now
allocated in the pci_assign_irq() callback automatically, PCI host bridge
drivers can stop relying on pci_fixup_irqs() for IRQ allocation.
Drop pci_fixup_irqs() usage from PCI xilinx host bridge driver.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Since, through struct pci_host_bridge.map/swizzle_irq hooks, IRQs are now
allocated in the pci_assign_irq() callback automatically, PCI host bridge
drivers can stop relying on pci_fixup_irqs() for IRQ allocation
Drop pci_fixup_irqs() usage from PCI tegra host bridge driver.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
The introduction of pci_scan_root_bus_bridge() provides a PCI core API to
scan a PCI root bus backed by an already initialized struct pci_host_bridge
object, which simplifies the bus scan interface and makes the PCI scan root
bus interface easier to generalize as members are added to the struct
pci_host_bridge.
Convert PCI xilinx-nwl host code to pci_scan_root_bus_bridge() to improve
the PCI root bus scanning interface.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Bharat Kumar Gogada <bharat.kumar.gogada@xilinx.com>
The introduction of pci_scan_root_bus_bridge() provides a PCI core API to
scan a PCI root bus backed by an already initialized struct pci_host_bridge
object, which simplifies the bus scan interface and makes the PCI scan root
bus interface easier to generalize as members are added to the struct
pci_host_bridge.
Convert PCI rockchip host code to pci_scan_root_bus_bridge() to improve the
PCI root bus scanning interface.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Wenrui Li <wenrui.li@rock-chips.com>
Cc: Shawn Lin <shawn.lin@rock-chips.com>
The introduction of pci_scan_root_bus_bridge() provides a PCI core API to
scan a PCI root bus backed by an already initialized struct pci_host_bridge
object, which simplifies the bus scan interface and makes the PCI scan root
bus interface easier to generalize as members are added to the struct
pci_host_bridge.
Convert PCI host-common code to pci_scan_root_bus_bridge() to improve the
PCI root bus scanning interface.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Will Deacon <will.deacon@arm.com>
The introduction of pci_scan_root_bus_bridge() provides a PCI core API to
scan a PCI root bus backed by an already initialized struct pci_host_bridge
object, which simplifies the bus scan interface and makes the PCI scan root
bus interface easier to generalize as members are added to the struct
pci_host_bridge.
Convert PCI xgene host code to pci_scan_root_bus_bridge() to improve the
PCI root bus scanning interface.
Tested-by: Khuong Dinh <kdinh@apm.com> # with e1000e
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Tanmay Inamdar <tinamdar@apm.com>
The introduction of pci_scan_root_bus_bridge() provides a PCI core API to
scan a PCI root bus backed by an already initialized struct pci_host_bridge
object, which simplifies the bus scan interface and makes the PCI scan root
bus interface easier to generalize as members are added to the struct
pci_host_bridge.
Convert PCI xilinx host code to pci_scan_root_bus_bridge() to improve the
PCI root bus scanning interface.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Michal Simek <michal.simek@xilinx.com>
The introduction of pci_scan_root_bus_bridge() provides a PCI core API to
scan a PCI root bus backed by an already initialized struct pci_host_bridge
object, which simplifies the bus scan interface and makes the PCI scan root
bus interface easier to generalize as members are added to the struct
pci_host_bridge.
Convert PCI altera host code to pci_scan_root_bus_bridge() to improve the
PCI root bus scanning interface.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Ley Foon Tan <lftan@altera.com>
The introduction of pci_scan_root_bus_bridge() provides a PCI core API to
scan a PCI root bus backed by an already initialized struct pci_host_bridge
object, which simplifies the bus scan interface and makes the PCI scan root
bus interface easier to generalize as members are added to the struct
pci_host_bridge.
Convert PCI versatile host code to pci_scan_root_bus_bridge() to improve
the PCI root bus scanning interface.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
[bhelgaas: folded in fix from Arnd Bergmann <arnd@arndb.de>:
http://lkml.kernel.org/r/20170621215323.3921382-3-arnd@arndb.de]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Rob Herring <robh@kernel.org>
The introduction of pci_scan_root_bus_bridge() provides a PCI core API to
scan a PCI root bus backed by an already initialized struct pci_host_bridge
object, which simplifies the bus scan interface and makes the PCI scan root
bus interface easier to generalize as members are added to the struct
pci_host_bridge.
Convert PCI iproc host code to pci_scan_root_bus_bridge() to improve the
PCI root bus scanning interface.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Jon Mason <jonmason@broadcom.com>
The introduction of pci_scan_root_bus_bridge() provides a PCI core API to
scan a PCI root bus backed by an already initialized struct pci_host_bridge
object, which simplifies the bus scan interface and makes the PCI scan root
bus interface easier to generalize as members are added to the struct
pci_host_bridge.
Convert PCI rcar host code to pci_scan_root_bus_bridge() to improve the PCI
root bus scanning interface.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Simon Horman <horms@verge.net.au>
The introduction of pci_scan_root_bus_bridge() provides a PCI core API to
scan a PCI root bus backed by an already initialized struct pci_host_bridge
object, which simplifies the bus scan interface and makes the PCI scan root
bus interface easier to generalize as members are added to the struct
pci_host_bridge.
Convert PCI aardvark host code to pci_scan_root_bus_bridge() to improve the
PCI root bus scanning interface.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
With the introduction of pci_scan_root_bus_bridge() there is no need to
export pci_register_host_bridge() to other kernel subsystems other than the
PCI compilation unit that needs it.
Make pci_register_host_bridge() static to its compilation unit and convert
the existing drivers usage over to pci_scan_root_bus_bridge().
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Arnd Bergmann <arnd@arndb.de>
When probing the PCI host controller driver, if an error occurs, the probe
function code does not free memory allocated for the struct pci_host_bridge
resulting in memory leakage.
Move the struct pci_host_bridge allocation over to the respective devm
interface to fix the issue.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Arnd Bergmann <arnd@arndb.de>
When probing the PCI host controller driver, if an error occurs, the probe
function code does not free memory allocated for the struct pci_host_bridge
resulting in memory leakage.
Move the struct pci_host_bridge allocation over to the respective devm
interface to fix the issue.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Current ftpci100 driver host bridge controller driver requires struct
pci_bus to be created in order to mask and clear IRQs using standard PCI
bus config accessors.
This struct pci_bus dependency is fictitious and burdens the driver with
unneeded constraints (eg to use separate APIs to create and scan the root
bus).
Add PCI raw config space accessors to PCIe ftpci100 driver and remove the
fictitious struct pci_bus dependency.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
[bhelgaas: folded in raw PCI read accessor from
http://lkml.kernel.org/r/20170621162651.25315-1-linus.walleij@linaro.org
The clock piece of the above posting goes with the separate "Add clock
handling" patch.]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
The current iproc driver host bridge controller driver requires struct
pci_bus to be created in order to carry out PCI link checks with standard
PCI config space accessors.
This struct pci_bus dependency is fictitious and burdens the driver with
unneeded constraints (eg to use separate APIs to create and scan the root
bus).
Add PCI raw config space accessors to the iproc driver and remove the
fictitious struct pci_bus dependency.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Jon Mason <jonmason@broadcom.com>
The nwl_pcie_enable_msi() second parameter (ie "bus") is unused and creates
a fake dependency on the struct pci_bus that need not exist.
Remove it.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Bharat Kumar Gogada <bharat.kumar.gogada@xilinx.com>
Use the fwnode to create a named domain so diagnosis works.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: linux-pci@vger.kernel.org
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Christoph Hellwig <hch@lst.de>
Link: http://lkml.kernel.org/r/20170619235444.379861978@linutronix.de
Many PCI host controller drivers aren't prepared to have their devices
unbound from them forcefully (e.g., through /sys/.../<driver>/unbind), as
they don't provide any driver .remove callback, where they'd detach the
root bus, release resources, etc. Keeping the driver built in (i.e., not a
loadable module) is not enough; and providing no .remove callback just
means we don't do any teardown.
To rule out the possibility of unbinding a device via sysfs, we need to set
the ".suppress_bind_attrs" field.
I found the suspect drivers via the following search:
git grep -l platform_driver $(git grep -L -e '\.remove' -e suppress_bind_attrs drivers/pci/)
Then I inspected them to ensure that
(a) they set up a PCI bus in their probe() and
(b) they don't have a remove() callback for undoing the setup
Suggested-by: Bjorn Helgaas <helgaas@kernel.org>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
* pci/msi:
PCI/MSI: Use dev_printk() when possible
of/pci: Remove unused MSI controller helpers
PCI: mvebu: Remove useless MSI enabling code
PCI: aardvark: Move to MSI handling using generic MSI support
PCI/MSI: Make pci_msi_shutdown() and pci_msix_shutdown() static
PCI/MSI: Stop disabling MSI/MSI-X in pci_device_shutdown()
* pci/ioremap:
PCI: versatile: Update PCI config space remap function
PCI: keystone-dw: Update PCI config space remap function
PCI: layerscape: Update PCI config space remap function
PCI: hisi: Update PCI config space remap function
PCI: tegra: Update PCI config space remap function
PCI: xgene: Update PCI config space remap function
PCI: armada8k: Update PCI config space remap function
PCI: designware: Update PCI config space remap function
PCI: iproc-platform: Update PCI config space remap function
PCI: qcom: Update PCI config space remap function
PCI: rockchip: Update PCI config space remap function
PCI: spear13xx: Update PCI config space remap function
PCI: xilinx-nwl: Update PCI config space remap function
PCI: xilinx: Update PCI config space remap function
PCI: ECAM: Map config region with pci_remap_cfgspace()
PCI: Implement devm_pci_remap_cfgspace()
devres: fix devm_ioremap_*() offset parameter kerneldoc description
ARM: Implement pci_remap_cfgspace() interface
ARM64: Implement pci_remap_cfgspace() interface
linux/io.h: Add pci_remap_cfgspace() interface
PCI: Remove __weak tag from pci_remap_iospace()
* pci/host-rockchip:
PCI: rockchip: Modularize
PCI: Export pci_remap_iospace() and pci_unmap_iospace()
PCI: rockchip: Add remove() support
PCI: rockchip: Set PCI_EXP_LNKSTA_SLC in the Root Port
PCI: rockchip: Advertise 128-byte Read Completion Boundary support
PCI: rockchip: Make 'return 0' more obvious in probe()
PCI: rockchip: Unindent rockchip_pcie_set_power_limit()
PCI: rockchip: Handle regulator_get_current_limit() failure correctly
PCI configuration space should be mapped with a memory region type that
generates on the CPU host bus non-posted write transations. Update the
driver to use the devm_ioremap_nopost* interface to make sure the correct
memory mappings for PCI configuration space are used.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Rob Herring <robh@kernel.org>
PCI configuration space should be mapped with a memory region type that
generates on the CPU host bus non-posted write transations. Update the
driver to use correct memory mapping attributes to map config space
regions to enforce configuration space non-posted writes behaviour.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
PCI configuration space should be mapped with a memory region type that
generates on the CPU host bus non-posted write transations. Update the
driver to use the devm_pci_remap_cfg* interface to make sure the correct
memory mappings for PCI configuration space are used.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Tanmay Inamdar <tinamdar@apm.com>
PCI configuration space should be mapped with a memory region type that
generates on the CPU host bus non-posted write transations. Update the
driver to use the devm_pci_remap_cfg* interface to make sure the correct
memory mappings for PCI configuration space are used.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Jon Mason <jonmason@broadcom.com>
PCI configuration space should be mapped with a memory region type that
generates on the CPU host bus non-posted write transations. Update the
driver to use the devm_pci_remap_cfg* interface to make sure the correct
memory mappings for PCI configuration space are used.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Wenrui Li <wenrui.li@rock-chips.com>
Cc: Shawn Lin <shawn.lin@rock-chips.com>
PCI configuration space should be mapped with a memory region type that
generates on the CPU host bus non-posted write transations. Update the
driver to use the devm_pci_remap_cfg* interface to make sure the correct
memory mappings for PCI configuration space are used.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Bharat Kumar Gogada <bharat.kumar.gogada@xilinx.com>
Cc: Michal Simek <michal.simek@xilinx.com>
PCI configuration space should be mapped with a memory region type that
generates on the CPU host bus non-posted write transations. Update the
driver to use the devm_pci_remap_cfg* interface to make sure the correct
memory mappings for PCI configuration space are used.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Bharat Kumar Gogada <bharat.kumar.gogada@xilinx.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Now that we've exported pci_remap_iospace() and added proper remove()
support, there's no reason this can't be a loadable module.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Shawn Lin <shawn.lin@rock-chips.com>
Currently, if we try to unbind the platform device, the remove will
succeed, but the removal won't undo most of the registration, leaving
partially-configured PCI devices in the system.
This allows, for example, a simple 'lspci' to crash the system, as it will
try to touch the freed (via devm_*) driver structures, e.g., on RK3399:
# echo f8000000.pcie > /sys/bus/platform/drivers/rockchip-pcie/unbind
# lspci
So let's implement device remove().
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Shawn Lin <shawn.lin@rock-chips.com>
refcount_t type and corresponding API should be used instead of atomic_t
when the variable is used as a reference counter. This allows to avoid
accidental refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com>
Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David Windsor <dwindsor@gmail.com>
Reviewed-by: Stephen Hemminger <sthemmin@microsoft.com>
All platforms using Rockchip use a common clock for the Root Port and the
slot connected to it. Indicate this by setting the Slot Clock Configuration
(PCI_EXP_LNKSTA_SLC) bit in the Root Port's Link Status.
Per the Implementation Note in the spec (PCIe r3.1, sec 7.8.7), if the
downstream component also sets PCI_EXP_LNKSTA_SLC, software may set the
Common Clock Configuration (PCI_EXP_LNKCTL_CCC) bits on both ends of the
Link. This is done by pcie_aspm_configure_common_clock().
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Cc: Brian Norris <briannorris@chromium.org>
Cc: jeffy.chen <jeffy.chen@rock-chips.com>
The memory allocation here needs to be non-blocking. Fix the issue.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Long Li <longli@microsoft.com>
Cc: <stable@vger.kernel.org>
When we have 32 or more CPUs in the affinity mask, we should use a special
constant to specify that to the host. Fix this issue.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Long Li <longli@microsoft.com>
Cc: <stable@vger.kernel.org>
Rockchip Root Ports support either 64 or 128 byte Read Completion Boundary
(RCB). Set the RCB bit in the Link Control register to indicate this.
A 128 byte RCB significantly improves performance of NVMe with libaio.
[bhelgaas: changelog]
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Brian Norris <briannorris@chromium.org>
Cc: Jeffy Chen <jeffy.chen@rock-chips.com>
SZ_16M PEM resource size includes PEM-specific register and its children
resources. Reservation of the whole SZ_16M range leads to child device
driver failure when pcieport driver is requesting resources:
pcieport 0004:1f:00.0: can't enable device: BAR 0 [mem 0x87e0c0f00000-0x87e0c0ffffff 64bit] not claimed
So we cannot reserve full 16M here and instead we want to reserve
PEM-specific register only which is SZ_64K.
At the end increase PEM resource to SZ_16M since this is what
thunder_pem_init() call expects for proper initialization.
Fixes: 9abb27c759 ("PCI: thunder-pem: Add legacy firmware support for Cavium ThunderX host controller")
Signed-off-by: Tomasz Nowicki <tn@semihalf.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v4.10+
It seems on later Armada 38x, the slot clock configuration bit is not
read-only, but can be written. This means that our RW1C protection ends up
clearing this bit when the link control register is written.
Adjust the mask so that we only avoid writing '1' bits to the RW1C bits of
this register (bits 15 and 14 of the link status) rather than masking out
all the status register bits.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add a host bridge driver for the Faraday Technology FPPCI100 host bridge,
used for Cortina Systems Gemini SoC (SL3516) PCI Host Bridge.
This code is inspired by the out-of-tree OpenWRT patch and then extensively
rewritten for device tree and using the modern helpers to cut down and
modernize the code to all new PCI frameworks. A driver exists in U-Boot as
well.
Tested on the ITian Square One SQ201 NAS with the following result in the
boot log (trimmed to relevant parts):
OF: PCI: host bridge /soc/pci@50000000 ranges:
OF: PCI: IO 0x50000000..0x500fffff -> 0x00000000
OF: PCI: MEM 0x58000000..0x5fffffff -> 0x58000000
ftpci100 50000000.pci: PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [bus 00-ff]
pci_bus 0000:00: root bus resource [io 0x0000-0xfffff]
pci_bus 0000:00: root bus resource [mem 0x58000000-0x5fffffff]
ftpci100 50000000.pci:
DMA MEM1 BASE: 0x0000000000000000 -> 0x0000000007ffffff config 00070000
ftpci100 50000000.pci:
DMA MEM2 BASE: 0x0000000000000000 -> 0x0000000003ffffff config 00060000
ftpci100 50000000.pci:
DMA MEM3 BASE: 0x0000000000000000 -> 0x0000000003ffffff config 00060000
PCI: bus0: Fast back to back transfers disabled
pci 0000:00:00.0: of_irq_parse_pci() failed with rc=-22
pci 0000:00:0c.0: BAR 0: assigned [mem 0x58000000-0x58007fff]
pci 0000:00:09.2: BAR 0: assigned [mem 0x58008000-0x580080ff]
pci 0000:00:09.0: BAR 4: assigned [io 0x1000-0x101f]
pci 0000:00:09.1: BAR 4: assigned [io 0x1020-0x103f]
pci 0000:00:09.0: enabling device (0140 -> 0141)
pci 0000:00:09.0: HCRESET not completed yet!
pci 0000:00:09.1: enabling device (0140 -> 0141)
pci 0000:00:09.1: HCRESET not completed yet!
pci 0000:00:09.2: enabling device (0140 -> 0142)
rt61pci 0000:00:0c.0: enabling device (0140 -> 0142)
ieee80211 phy0: rt2x00_set_chip: Info - Chipset detected -
rt: 2561, rf: 0003, rev: 000c
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-pci: EHCI PCI platform driver
ehci-pci 0000:00:09.2: EHCI Host Controller
ehci-pci 0000:00:09.2: new USB bus registered, assigned bus number 1
ehci-pci 0000:00:09.2: irq 125, io mem 0x58008000
ehci-pci 0000:00:09.2: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
uhci_hcd: USB Universal Host Controller Interface driver
uhci_hcd 0000:00:09.0: UHCI Host Controller
uhci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:09.0: HCRESET not completed yet!
uhci_hcd 0000:00:09.0: irq 123, io base 0x00001000
hub 2-0:1.0: USB hub found
hub 2-0:1.0: config failed, hub doesn't have any ports! (err -19)
uhci_hcd 0000:00:09.1: UHCI Host Controller
uhci_hcd 0000:00:09.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:09.1: HCRESET not completed yet!
uhci_hcd 0000:00:09.1: irq 124, io base 0x00001020
hub 3-0:1.0: USB hub found
hub 3-0:1.0: config failed, hub doesn't have any ports! (err -19)
scsi 0:0:0:0: Direct-Access USB Flash Disk 1.00 PQ: 0 ANSI: 2
sd 0:0:0:0: [sda] 7900336 512-byte logical blocks: (4.04 GB/3.77 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] No Caching mode page found
sd 0:0:0:0: [sda] Assuming drive cache: write through
sda: sda1 sda2 sda3
sd 0:0:0:0: [sda] Attached SCSI removable disk
ieee80211 phy0: rt2x00lib_request_firmware: Info -
Loading firmware file 'rt2561s.bin'
ieee80211 phy0: rt2x00lib_request_firmware: Info -
Firmware detected - version: 0.8
IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
$ lspci
00:00.0 Class 0600: 159b:4321
00:09.2 Class 0c03: 1106:3104
00:09.0 Class 0c03: 1106:3038
00:09.1 Class 0c03: 1106:3038
00:0c.0 Class 0280: 1814:0301
$ cat /proc/interrupts
CPU0
123: 0 PCI 0 Edge uhci_hcd:usb2
124: 0 PCI 1 Edge uhci_hcd:usb3
125: 159 PCI 2 Edge ehci_hcd:usb1
126: 1082 PCI 3 Edge rt61pci
$ cat /proc/iomem
50000000-500000ff : /soc/pci@50000000
58000000-5fffffff : Gemini PCI MEM
58000000-58007fff : 0000:00:0c.0
58000000-58007fff : 0000:00:0c.0
58008000-580080ff : 0000:00:09.2
58008000-580080ff : ehci_hcd
The EHCI USB hub works fine; I can mount and manage files and the IRQs just
keep ticking up. I can issue iwlist wlan0 scanning and see all the WLANs
here. I don't have wpa_supplicant so have not tried connecting to them.
[bhelgaas: fold in %pap change from Arnd Bergmann <arnd@arndb.de>]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Janos Laube <janos.dev@gmail.com>
CC: Paulius Zaleckas <paulius.zaleckas@gmail.com>
CC: Hans Ulli Kroll <ulli.kroll@googlemail.com>
CC: Florian Fainelli <f.fainelli@gmail.com>
CC: Feng-Hsin Chiang <john453@faraday-tech.com>
CC: Greentime Hu <green.hu@gmail.com>
A PCI_EJECT message can arrive at the same time we are calling
pci_scan_child_bus() in the workqueue for the previous PCI_BUS_RELATIONS
message or in create_root_hv_pci_bus(). In this case we could potentially
modify the bus from multiple places.
Properly lock the bus access.
Thanks Dexuan Cui <decui@microsoft.com> for pointing out the race condition
in create_root_hv_pci_bus().
Reported-by: Xiaofeng Wang <xiaofwan@redhat.com>
Signed-off-by: Long Li <longli@microsoft.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: K. Y. Srinivasan <kys@microsoft.com>
hv_pci_devices_present() is called in hv_pci_remove() when we remove a PCI
device from the host, e.g., by disabling SR-IOV on a device. In
hv_pci_remove(), the bus is already removed before the call, so we don't
need to rescan the bus in the workqueue scheduled from
hv_pci_devices_present().
By introducing bus state hv_pcibus_removed, we can avoid this situation.
Reported-by: Xiaofeng Wang <xiaofwan@redhat.com>
Signed-off-by: Long Li <longli@microsoft.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: K. Y. Srinivasan <kys@microsoft.com>
There's no way to get here with 'err != 0'. Just return 0 to be more
obvious and prevent future changes from accidentally erroring out here
without going through the right error paths.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
If regulator_get_current_limit() returns 0 or error, return early so the
body of the function doesn't have to be indented as the body of an "if"
statement. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
During early days of PCI quirks support, ThunderX firmware did not provide
PNP0c02 node with PCI configuration space and PEM-specific register ranges.
This means that for legacy FW we are not reserving these resources and
cannot gather PEM-specific resources for further PEM initialization.
To support already deployed legacy FW, calculate PEM-specific ranges and
provide resources reservation as fallback scenario into PEM driver when we
could not gather PEM reg base from ACPI tables.
Tested-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: Tomasz Nowicki <tn@semihalf.com>
Signed-off-by: Vadim Lomovtsev <Vadim.Lomovtsev@caviumnetworks.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Robert Richter <rrichter@cavium.com>
CC: stable@vger.kernel.org # v4.10+
"CAV" is the only PNP/ACPI hardware ID vendor prefix assigned to Cavium so
fix this as it should be from day one.
Fixes: 44f22bd91e ("PCI: Add MCFG quirks for Cavium ThunderX pass2.x host controller")
Tested-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: Tomasz Nowicki <tn@semihalf.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Robert Richter <rrichter@cavium.com>
CC: stable@vger.kernel.org # v4.10+
