Commit 16200948d8 ("ALSA: usb-audio: Fix race at stopping the stream") was
incomplete causing another more severe kernel panic, so it got reverted.
This fixes both the original problem and its fallout kernel race/crash.
The original fix is to move the endpoint member NULL clearing logic inside
wait_clear_urbs() so the irq triggering the urb completion doesn't call
retire_capture/playback_urb() after the NULL clearing and generate a panic.
However this creates a new race between snd_usb_endpoint_start()'s call
to wait_clear_urbs() and the irq urb completion handler which again calls
retire_capture/playback_urb() leading to a new NULL dereference.
We keep the EP deactivation code in snd_usb_endpoint_start() because
removing it will break the EP reference counting (see [1] [2] for info),
however we don't need the "can_sleep" mechanism anymore because a new
function was introduced (snd_usb_endpoint_sync_pending_stop()) which
synchronizes pending stops and gets called inside the pcm prepare callback.
It also makes sense to remove can_sleep because it was also removed from
deactivate_urbs() signature in [3] so we benefit from more simplification.
[1] commit 015618b90 ("ALSA: snd-usb: Fix URB cancellation at stream start")
[2] commit e9ba389c5 ("ALSA: usb-audio: Fix scheduling-while-atomic bug in PCM capture stream")
[3] commit ccc1696d5 ("ALSA: usb-audio: simplify endpoint deactivation code")
Fixes: f8114f8583 ("Revert "ALSA: usb-audio: Fix race at stopping the stream"")
Signed-off-by: Ioan-Adrian Ratiu <adi@adirat.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Axe-Fx II implicit feedback end point and the data sync endpoint
are in different interface descriptors. Add quirk to ensure a sync
endpoint is properly configured.
Signed-off-by: Alberto Aguirre <albaguirre@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some of userland applications call 'snd_pcm_hw_params()' and
'snd_pcm_hw_prepare()' sequentially, which means 'snd_pcm_hw_prepare()'
is called twice and the second 'snd_pcm_hw_prepare()' is called in
'SNDRV_PCM_STATE_PREPARED' state.
Some devices are not able to manage this and they will stop playback
if the sample rate will be configured several times over USB protocol.
V2: updated Changelog
Signed-off-by: Daniel Girnus <dgirnus@de.adit-jv.com>
Signed-off-by: Jens Lorenz <jlorenz@de.adit-jv.com>
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Unfortunately, this patch caused several regressions at au0828 and
snd-usb-audio, like this one:
https://bugzilla.kernel.org/show_bug.cgi?id=115561
It also showed several troubles at the MC core that handles pretty
poorly the memory protections and data lifetime management.
So, better to revert it and fix the core before reapplying this
change.
This reverts commit aebb2b89bf ("[media] sound/usb: Use Media
Controller API to share media resources")'
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
After a heavy storm by syzkaller in 4.5 cycle, we have relatively few
changes in the core at this time while a lot of changes are found in
the driver side, unsurprisingly. Below are some highlights:
ALSA core:
- A few more hardening in ALSA timer codes
- An extension of sequencer API for advertising the card / pid
- Small fixes in compress-offload and jack layers
HD-audio:
- Dynamic PCM assignment in HDMI/DP codec; preparation for upcoming
DP-MST support
- Lots of code refactoring for sharing with ASoC SKL driver
- Regression fixes for Intel HDMI/DP
- Fixups for CX20724 codec, Lenovo AiO
USB-audio:
- Add quirk_alias option to make quirk debugging easier
- Fixes for possible Oops by malformed firmware
Firewire:
- Add support for FW-1804 in tascam driver
- Improvements / changes in card registration, multi stream handling,
etc for DICE
- Lots of code refactoring
ASoC:
- Enhancements of still ongoing topology API
- Lots of commits for Intel Skylake support including HDMI support
- A few Intel Atom driver updates for recent devices
- Lots of improvements to the Renesas drivers
- Capture support for Qualcomm drivers
- Support for TI DaVinci DRA7xxx devices
- New machine drivers for Freescale systems with Cirrus CODECs,
Mediatek systems with RT5650 CODECs
- New CPU drivers for Allwinner S/PDIF controllers
- New CODEC drivers for Maxim MAX9867 and MAX98926 and Realtek RT5514
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=Cc+v
-----END PGP SIGNATURE-----
Merge tag 'sound-4.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"After a heavy storm by syzkaller in 4.5 cycle, we have relatively few
changes in the core at this time while a lot of changes are found in
the driver side, unsurprisingly. Below are some highlights:
ALSA core:
- A few more hardening in ALSA timer codes
- An extension of sequencer API for advertising the card / pid
- Small fixes in compress-offload and jack layers
HD-audio:
- Dynamic PCM assignment in HDMI/DP codec; preparation for upcoming
DP-MST support
- Lots of code refactoring for sharing with ASoC SKL driver
- Regression fixes for Intel HDMI/DP
- Fixups for CX20724 codec, Lenovo AiO
USB-audio:
- Add quirk_alias option to make quirk debugging easier
- Fixes for possible Oops by malformed firmware
Firewire:
- Add support for FW-1804 in tascam driver
- Improvements / changes in card registration, multi stream handling,
etc for DICE
- Lots of code refactoring
ASoC:
- Enhancements of still ongoing topology API
- Lots of commits for Intel Skylake support including HDMI support
- A few Intel Atom driver updates for recent devices
- Lots of improvements to the Renesas drivers
- Capture support for Qualcomm drivers
- Support for TI DaVinci DRA7xxx devices
- New machine drivers for Freescale systems with Cirrus CODECs,
Mediatek systems with RT5650 CODECs
- New CPU drivers for Allwinner S/PDIF controllers
- New CODEC drivers for Maxim MAX9867 and MAX98926 and Realtek RT5514"
* tag 'sound-4.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (291 commits)
ALSA: hda - Fix mutex deadlock at HDMI/DP hotplug
ALSA: ctl: change return value in compatibility layer so that it's the same value in core implementation
ALSA: mixart: silence an uninitialized variable warning
ALSA: usb-audio: Add sanity checks for endpoint accesses
ALSA: usb-audio: Minor code cleanup in create_fixed_stream_quirk()
ALSA: usb-audio: Fix NULL dereference in create_fixed_stream_quirk()
ALSA: hda - Limit i915 HDMI binding only for HSW and later
ALSA: hda - Fix unconditional GPIO toggle via automute
ALSA: mixart: silence unitialized variable warnings
ALSA: hda - Fixes double fault in nvhdmi_chmap_cea_alloc_validate_get_type
ALSA: intel8x0: Add clock quirk entry for AD1981B on IBM ThinkPad X41.
ALSA: hda - Add new GPU codec ID 0x10de0082 to snd-hda
ASoC: rsnd: add simplified module explanation
ASoC: hdac_hdmi: Add broxton device ID
ASoC: Intel: Bxtn: Add Broxton PCI ID
ASoC: Intel: Skylake: Move Skylake dsp ops & loader ops
ASoC: Intel: add dmabuffer to common sst_dsp
ASoC: Intel: Skylake: Unstatify skl_dsp_enable_core
ASoC: Intel: Skylake: Fix whitepsace issues
ASoC: Intel: Skylake: Move module id defines
...
Add some sanity check codes before actually accessing the endpoint via
get_endpoint() in order to avoid the invalid access through a
malformed USB descriptor. Mostly just checking bNumEndpoints, but in
one place (snd_microii_spdif_default_get()), the validity of iface and
altsetting index is checked as well.
Bugzilla: https://bugzilla.suse.com/show_bug.cgi?id=971125
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Change ALSA driver to use Media Controller API to share media resources
with DVB and V4L2 drivers on a AU0828 media device. Media Controller
specific initialization is done after sound card is registered. ALSA
creates Media interface and entity function graph nodes for Control,
Mixer, PCM Playback, and PCM Capture devices.
snd_usb_hw_params() will call Media Controller enable source handler
interface to request the media resource. If resource request is
granted, it will release it from snd_usb_hw_free(). If resource is
busy, -EBUSY is returned.
Media specific cleanup is done in usb_audio_disconnect().
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The Zoom R16/24 have a nonstandard playback format where each isochronous
packet contains a length descriptor in the first four bytes. (Curiously,
capture data does not contain this and requires no quirk.)
The quirk involves adding the extra length descriptor whenever outgoing
isochronous packets are generated, both in pcm.c (outgoing audio) and
endpoint.c (silent data).
In order to make the quirk as unintrusive as possible, for
pcm.c:prepare_playback_urb(), the isochronous packet descriptors are
initially set up in the same way no matter if the quirk is enabled or not.
Once it is time to actually copy the data into the outgoing packet buffer
(together with the added length descriptors) the isochronous descriptors
are adjusted in order take the increased payload length into account.
For endpoint.c:prepare_silent_urb() it makes more sense to modify the
actual function, partly because the function is less complex to start with
and partly because it is not as time-critical as prepare_playback_urb()
(whose bulk is run with interrupts disabled), so the (minute) additional
time spent in the non-quirk case is motivated by the simplicity of having
a single function for all cases.
The quirk is controlled by the new tx_length_quirk member in struct
snd_usb_substream and struct snd_usb_audio, which is conveyed to pcm.c
and endpoint.c from quirks.c in a similar manner to the txfr_quirk member
in the same structs.
In contrast to txfr_quirk however, the quirk is enabled directly in
quirks.c:create_standard_audio_quirk() by checking the USB ID in that
function. Another option would be to introduce a new
QUIRK_AUDIO_ZOOM_INTERFACE or somesuch, which would have made the quirk
very plain to see in the quirk table, but it was felt that the additional
code needed to implement it this way would just make the implementation
more complex with no real gain.
Tested with a Zoom R16, both by doing capture and playback separately
using arecord and aplay (8 channel capture and 2 channel playback,
respectively), as well as capture and playback together using Ardour, as
well as Audacity and Qtractor together with jackd.
The R24 is reportedly compatible with the R16 when used as an audio
interface. Both devices share the same USB ID and have the same number of
inputs (8) and outputs (2). Therefore "R16/24" is mentioned throughout the
patch.
Regression tested using an Edirol UA-5 in both class compliant (16-bit)
and "advanced" (24 bit, forces the use of quirks) modes.
Signed-off-by: Ricard Wanderlof <ricardw@axis.com>
Tested-by: Panu Matilainen <pmatilai@laiskiainen.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
After the recent fix of runtime PM for USB-audio driver, we got a
lockdep warning like:
=============================================
[ INFO: possible recursive locking detected ]
4.2.0-rc8+ #61 Not tainted
---------------------------------------------
pulseaudio/980 is trying to acquire lock:
(&chip->shutdown_rwsem){.+.+.+}, at: [<ffffffffa0355dac>] snd_usb_autoresume+0x1d/0x52 [snd_usb_audio]
but task is already holding lock:
(&chip->shutdown_rwsem){.+.+.+}, at: [<ffffffffa0355dac>] snd_usb_autoresume+0x1d/0x52 [snd_usb_audio]
This comes from snd_usb_autoresume() invoking down_read() and it's
used in a nested way. Although it's basically safe, per se (as these
are read locks), it's better to reduce such spurious warnings.
The read lock is needed to guarantee the execution of "shutdown"
(cleanup at disconnection) task after all concurrent tasks are
finished. This can be implemented in another better way.
Also, the current check of chip->in_pm isn't good enough for
protecting the racy execution of multiple auto-resumes.
This patch rewrites the logic of snd_usb_autoresume() & co; namely,
- The recursive call of autopm is avoided by the new refcount,
chip->active. The chip->in_pm flag is removed accordingly.
- Instead of rwsem, another refcount, chip->usage_count, is introduced
for tracking the period to delay the shutdown procedure. At
the last clear of this refcount, wake_up() to the shutdown waiter is
called.
- The shutdown flag is replaced with shutdown atomic count; this is
for reducing the lock.
- Two new helpers are introduced to simplify the management of these
refcounts; snd_usb_lock_shutdown() increases the usage_count, checks
the shutdown state, and does autoresume. snd_usb_unlock_shutdown()
does the opposite. Most of mixer and other codes just need this,
and simply returns an error if it receives an error from lock.
Fixes: 9003ebb13f ('ALSA: usb-audio: Fix runtime PM unbalance')
Reported-and-tested-by: Alexnader Kuleshov <kuleshovmail@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The M-Audio Transit exposes an interface with a SYNC_NONE attribute.
This is not a valid value according to the USB audio classspec. However
there is a sync endpoint associated to this record. Changing the logic to
try to use this sync endpoint allows for seamless transitions between
altset 2 and altset 3. If any errors happen, the behavior remains the same.
$ more /proc/asound/card1/stream0
M-Audio Transit USB at usb-0000:00:14.0-2, full speed : USB Audio
Playback:
Status: Stop
Interface 1
Altset 1
Format: S24_3LE
Channels: 2
Endpoint: 3 OUT (ADAPTIVE)
Rates: 48001 - 96000 (continuous)
Interface 1
Altset 2
Format: S24_3LE
Channels: 2
Endpoint: 3 OUT (NONE)
Rates: 8000 - 48000 (continuous)
Interface 1
Altset 3
Format: S16_LE
Channels: 2
Endpoint: 3 OUT (ASYNC)
Rates: 8000 - 48000 (continuous)
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When a transition occurs between alternate settings that do not use the
same synchronization method, the substream pointers were not reset.
This prevents audio from being played during the second transition.
Identified and tested with M-Audio Transit device
(0763:2006 Midiman M-Audio Transit)
Details of the issue:
First playback to adaptive endpoint:
$ aplay -Dhw:1,0 ~/24_96.wav
Playing WAVE '/home/plb/24_96.wav' : Signed 24 bit Little Endian in 3bytes,
Rate 96000 Hz, Stereo
[ 3169.297556] usb 1-2: setting usb interface 1:1
[ 3169.297568] usb 1-2: Creating new playback data endpoint #3
[ 3169.298563] usb 1-2: Setting params for ep #3 (type 0, 3 urbs), ret=0
[ 3169.298574] usb 1-2: Starting data EP @ffff880035fc8000
first playback to asynchronous endpoint:
$ aplay -Dhw:1,0 ~/16_48.wav
Playing WAVE '/home/plb/16_48.wav' : Signed 16 bit Little Endian,
Rate 48000 Hz, Stereo
[ 3204.520251] usb 1-2: setting usb interface 1:3
[ 3204.520264] usb 1-2: Creating new playback data endpoint #3
[ 3204.520272] usb 1-2: Creating new capture sync endpoint #83
[ 3204.521162] usb 1-2: Setting params for ep #3 (type 0, 4 urbs), ret=0
[ 3204.521177] usb 1-2: Setting params for ep #83 (type 1, 4 urbs), ret=0
[ 3204.521182] usb 1-2: Starting data EP @ffff880035fce000
[ 3204.521204] usb 1-2: Starting sync EP @ffff8800bd616000
second playback to adaptive endpoint: no audio and error on terminal:
$ aplay -Dhw:1,0 ~/24_96.wav
Playing WAVE '/home/plb/24_96.wav' : Signed 24 bit Little Endian in 3bytes,
Rate 96000 Hz, Stereo
aplay: pcm_write:1939: write error: Input/output error
[ 3239.483589] usb 1-2: setting usb interface 1:1
[ 3239.483601] usb 1-2: Re-using EP 3 in iface 1,1 @ffff880035fc8000
[ 3239.484590] usb 1-2: Setting params for ep #3 (type 0, 4 urbs), ret=0
[ 3239.484606] usb 1-2: Setting params for ep #83 (type 1, 4 urbs), ret=0
This last line shows that a sync endpoint is used when it shouldn't.
The sync endpoint is no longer valid and the pointers are corrupted
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The first URBs are submitted during the prepare stage. When .trigger is
called, the ALSA core saves a trigger tstamp that doesn't correspond to
the actual time when the samples are submitted. The trigger_tstamp is
now updated when the first data are submitted to avoid any time offsets.
A usb-specific trigger_tstamp_pending_update flag is used for now,
at some point the flag would need to move to the ALSA core, USB
is not the only interface where silent block transfers are programmed
as part of the prepare stage, with actual data enabled when .trigger
is called.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Denon/Marantz USB DACs need a specific vendor command to switch between PCM and
DSD mode. This patch adds a new quirk function to switch between the two modes
using the specific USB vendor command.
This patch applies to the following devices:
- Marantz SA-14S1
- Marantz HD-DAC1
Signed-off-by: Jurgen Kramer <gtmkramer@xs4all.nl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This (widely used) construction:
if(printk_ratelimit())
dev_dbg()
Causes the ratelimiting to spam the kernel log with the "callbacks suppressed"
message below, even while the dev_dbg it is supposed to rate limit wouldn't
print anything because DEBUG is not defined for this device.
[ 533.803964] retire_playback_urb: 852 callbacks suppressed
[ 538.807930] retire_playback_urb: 852 callbacks suppressed
[ 543.811897] retire_playback_urb: 852 callbacks suppressed
[ 548.815745] retire_playback_urb: 852 callbacks suppressed
[ 553.819826] retire_playback_urb: 852 callbacks suppressed
So use dev_dbg_ratelimited() instead of this construction.
Signed-off-by: Sander Eikelenboom <linux@eikelenboom.it>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
BugLink: http://bugs.launchpad.net/bugs/1305133
Malfunctioning or slow devices can cause a flood of dmesg SPAM.
I've ignored checkpatch.pl complaints about the use of printk_ratelimit() in favour
of prior art in sound/usb/pcm.c.
WARNING: Prefer printk_ratelimited or pr_<level>_ratelimited to printk_ratelimit
+ if (printk_ratelimit() &&
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Eldad Zack <eldad@fogrefinery.com>
Cc: Daniel Mack <zonque@gmail.com>
Cc: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Convert with dev_err() and co from snd_printk(), etc.
As there are too deep indirections (e.g. ep->chip->dev->dev),
a few new local macros, usb_audio_err() & co, are introduced.
Also, the device numbers in some messages are dropped, as they are
shown in the prefix automatically.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As Clemens Ladisch kindly explained:
"Please note that there are two methods to identify alternate settings:
the number, which is the value in bAlternateSetting, and the index,
which is the index in the descriptor array. There might be some wording
in the USB spec that these two values must be the same, but in reality,
[insert standard rant about firmware writers], bAlternateSetting
must be treated as a random ID value."
This patch changes the name to express the correct usage semantics.
No functional change.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If setting the interface fails, the SUBSTREAM_FLAG_SYNC_EP_STARTED
should be cleared.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The only call site for deactivate_endpoints() at snd_usb_hw_free().
The return value is not checked there, as it is irrelevant if it
fails on hw_free.
This patch moves the deactivation of the endpoints directly into
snd_usb_hw_free().
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch changes the way URBs are allocated and their sizes are
determined for PCM playback in the snd-usb-audio driver. Currently
the driver allocates too few URBs for endpoints that don't use
implicit sync, making underruns more likely to occur. This may be a
holdover from before I/O delays could be measured accurately; in any
case, it is no longer necessary.
The patch allocates as many URBs as possible, subject to four
limitations:
The total number of URBs for the endpoint is not allowed to
exceed MAX_URBS (which the patch increases from 8 to 12).
The total number of packets per URB is not allowed to exceed
MAX_PACKS (or MAX_PACKS_HS for high-speed devices), which is
decreased from 20 to 6.
The total duration of queued data is not allowed to exceed
MAX_QUEUE, which is decreased from 24 ms to 18 ms.
The total number of ALSA frames in the output queue is not
allowed to exceed the ALSA buffer size.
The last requirement is the hardest to implement. Currently the
number of URBs needed to fill a buffer cannot be determined in
advance, because a buffer contains a fixed number of frames whereas
the number of frames in an URB varies to match shifts in the device's
clock rate. To solve this problem, the patch changes the logic for
deciding how many packets an URB should contain. Rather than using as
many as possible without exceeding an ALSA period boundary, now the
driver uses only as many packets as needed to transfer a predetermined
number of frames. As a result, unless the device's clock has an
exceedingly variable rate, the number of URBs making up each period
(and hence each buffer) will remain constant.
The overall effect of the patch is that playback works better in
low-latency settings. The user can still specify values for
frames/period and periods/buffer that exceed the capabilities of the
hardware, of course. But for values that are within those
capabilities, the performance will be improved. For example, testing
shows that a high-speed device can handle 32 frames/period and 3
periods/buffer at 48 KHz, whereas the current driver starts to get
glitchy at 64 frames/period and 2 periods/buffer.
A side effect of these changes is that the "nrpacks" module parameter
is no longer used. The patch removes it.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Clemens Ladisch <clemens@ladisch.de>
Tested-by: Daniel Mack <zonque@gmail.com>
Tested-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since the quirks all apply to implicit feedback (the source endpoint
is always a data endpoint), there's no need to set and check
a flag for it.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
An implicit feedback endpoint can only be a capture source. The
consumer (sink) of the implicit feedback endpoint is therefore limited
to playback EPs.
Check if the target endpoint is a playback first and remove redundant
checks.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since implicit_fb is not changed, !implicit_fb will always
be true - it is set only after these checks.
Similarly, there's also no need to set it at the top of the function.
Change the type of implicit_fb to bool (more appropriate).
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reverse logic on the conditions required to qualify for a sync endpoint
and remove one level of indendation.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Separate setting implicit feedback quirks from setting
a sync endpoint (which may also be explicit feedback or async).
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Setting the sync endpoint currently takes up about half of set_format().
Move it to a dedicated function.
No functional change.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
All the Roland/Edirol/BOSS USB audio devices that need implicit feedback
show this unambiguously in their descriptors, so it might be a good idea
to let the driver detect this.
This should make playback work correctly (at least with Jack) with the
following devices:
- BOSS GT-100
- BOSS JS-8 Jam Station
- Edirol M-16DX
- Roland GAIA SH-01
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Instead of reading bInterfaceProtocol from the descriptor whenever it's
needed, store this value in the audioformat structure. Besides
simplifying some code, this will allow us to correctly handle vendor-
specific devices where the descriptors are marked with other values.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Add a function to handle conversion from snd_pcm_format_t
to bitwise with proper typing.
Change such conversions to use this function and silence sparse
warnings.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There is quite some confusion around the bit-ordering in DSD samples,
and no general agreement that defines whether hardware is supposed to
expect the oldest sample in the MSB or the LSB of a byte.
ALSA will hence set the rule that on the software API layer, bytes
always carry the oldest bit in the most significant bit of a byte, and
the driver has to translate that at runtime in order to match the
hardware layout.
This patch adds support for this by adding a boolean flag to the
audio format struct.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In order to provide a compatibility way for pushing DSD
samples through ordinary PCM channels, the "DoP open Standard" was
invented. See http://www.dsd-guide.com for the official document.
The host is required to stuff DSD marker bytes (0x05, 0xfa,
alternating) in the MSB of 24 bit wide samples on the bus, in addition
to the 16 bits of actual DSD sample payload.
To support this, the hardware and software stride logic in the driver
has to be tweaked a bit, as we make the userspace believe we're
operating on 16 bit samples, while we in fact push one more byte per
channel down to the hardware.
The DOP runtime information is stored in struct snd_usb_substream, so
we can keep track of our state across multiple calls to
prepare_playback_urb_dsd_dop().
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For normal PCM transfer, this change has no effect, as the endpoint's
stride is always frame_bits/8. For DSD DOP streams, however, which is
added later, the hardware stride differs from the software stride, and
the endpoint has the correct information in these cases.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When recording at 176.2KHz or 192Khz, the device adds a 32-bit length
header to the capture packets, which obviously needs to be ignored for
recording to work properly.
Userspace expected: L0 L1 L2 R0 R1 R2
...but actually got: R2 L0 L1 L2 R0 R1
Also, the last byte of the length header being interpreted as L0 of
the first sample caused spikes every 0.5ms, resulting in a loud 16KHz
tone (about the highest 'B' on a piano) being present throughout
captures.
Tested at all sample rates on an E-Mu 0404USB, and tested for
regressions on a generic USB headset.
Signed-off-by: Calvin Owens <jcalvinowens@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It turns out the devices from Playback Design need the delay quirk
after usb_set_interface from clocks.c as well. Make it a proper
quirks function and factor out the code to quirks.c.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Correct spelling of snd_usb_endpoint_implict_feedback_sink in all
occurances.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
"Playback Design" products need a 50ms delay after setting the USB
interface.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reported-by: Andreas Koch <andreas@akdesigninc.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Adds quirks and mixer support for the M-Audio Fast Track C600 USB
audio interface. This device is very similar to the C400 - the C600
simply has some more inputs and outputs, so the existing C400 support
is extended to support this device as well.
Signed-off-by: Matt Gruskin <matthew.gruskin@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Because currently snd_printd() and snd_printdd() macros are expanded
to empty when CONFIG_SND_DEBUG=n, a compile warning like below
appears sometimes, and we had to covert it by ugly ifdefs:
sound/pci/hda/patch_sigmatel.c: In function ‘stac92hd71bxx_fixup_hp’:
sound/pci/hda/patch_sigmatel.c:2434:24: warning: unused variable ‘spec’ [-Wunused-variable]
For "fixing" these issues better, this patch replaces snd_printd() and
snd_printdd() definitions with empty inline functions instead of
macros. This should have the same effect but shut up warnings like
above.
But since we had already put ifdefs, changing to inline functions
would trigger compile errors. So, such ifdefs is removed in this
patch.
In addition, snd_pci_quirk name field is defined only when
CONFIG_SND_DEBUG_VERBOSE is set, and the reference to it in
snd_printdd() argument triggers the build errors, too. For avoiding
these errors, introduce a new macro snd_pci_quirk_name() that is
defined no matter how the debug option is set.
Reported-by: Stratos Karafotis <stratosk@semaphore.gr>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The commit [0d9741c0: ALSA: usb-audio: sync ep init fix for
audioformat mismatch] introduced the correction of parameters to be
set for sync EP. But since the new code assumes that the sync EP is
always paired with the data EP of another direction, it triggers Oops
when a device only with a single direction is used.
This patch adds a proper check of sync EP type and the presence of the
paired substream for avoiding the crash.
Reported-and-tested-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Enable delay report on capture path. The delay is reset when an
URB is retired and increment at each call to .pointer based
on frame counter changes. The precision of the delay
information is limited to 1ms as in the playback case.
This reverts commit 3f94fad095.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit 947d299686 , "ALSA: snd-usb:
properly initialize the sync endpoint", while correcting the
initialization of the sync endpoint when opening just the data
endpoint, prevents devices that has a sync endpoint, with a channel
number different than that of the data endpoint, from functioning.
Due to a different channel and period bytes count, attempting to
initialize the sync endpoint will fail at the usb host driver.
For example, when using xhci:
cannot submit urb 0, error -90: internal error
With this patch, if a sync endpoint has multiple audioformats, a
matching audioformat is preferred. An audioformat must be found
with at least one channel and support the requested sample rate
and PCM format, otherwise the stream will not be opened.
If the number of channels differ between the selected audioformat
and the requested format, adjust the period bytes count accordingly.
It is safe to perform the calculation on the basis of the channel
count, since the requested PCM audio format and the rate must be
supported by the selected audioformat.
Cc: Jeffrey Barish <jeff_barish@earthlink.net>
Cc: Daniel Mack <zonque@gmail.com>
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The playback endpoint uses implicit feedback mode, similar
to the M-Audio FTU. Like with the FTU, we need to associate
the sync pipe ourselves.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When a playback stream is paused, the stream isn't actually stopped,
thus we still need to take care of the in-flight data amount for the
delay calculation. Otherwise the value of subs->last_delay is no
longer reliable and can give a bogus value after resuming from pause.
This will result in "delay: estimated XX, actual YY" error messages.
Also, during pause after all in flight data are processed
(i.e. last_delay = 0), we don't have to calculate the actual delay
from the current frame. Give a short path in such a case.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It doesn't make sense to calculate the delay for capture streams in
the current implementation. It's always zero, so we should skip the
computation in snd_usb_pcm_pointer() in the case of capture.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Jeffrey Barish reported an obvious bug in the pcm part of the usb-audio
driver which causes the code to not initialize the sync endpoint from
configure_endpoint().
Reported-by: Jeffrey Barish <jeff_barish@earthlink.net>
Signed-off-by: Daniel Mack <zonque@gmail.com>
Cc: stable@kernel.org [3.5+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
PCM hw_free and close should wait until all the pending stop
operations have been finished. Basically only PCM trigger callback
should use non-wait calls.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As we are stopping the endpoints asynchronously now, it's better to
trigger the stop of both data and sync endpoints and wait for pending
stopping operations, instead of the sequential trigger-and-wait
procedure.
So the wait argument in snd_usb_endpoint_stop() is dropped, and it's
expected that the caller synchronizes explicitly by calling
snd_usb_endpoint_sync_pending_stop(). (Actually there is only one
place calling this, so it was safe to change.)
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reduce the redundant arguments for snd_usb_endpoint_start() and
snd_usb_endpoint_stop(). Also replaced from int to bool.
No functional changes by this commit.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There are bug reports of a crash with USB-audio devices when PCM
prepare is performed immediately after the stream is stopped via
trigger callback. It turned out that the problem is that we don't
wait until all URBs are killed.
This patch adds a new function to synchronize the pending stop
operation on an endpoint, and calls in the prepare callback for
avoiding the crash above.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=49181
Reported-and-tested-by: Artem S. Tashkinov <t.artem@lycos.com>
Cc: <stable@vger.kernel.org> [v3.6]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Replace mutex with rwsem for codec->shutdown protection so that
concurrent accesses are allowed.
Also add the protection to snd_usb_autosuspend() and
snd_usb_autoresume(), too.
Reported-by: Matthieu CASTET <matthieu.castet@parrot.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Close some races at disconnection of a USB audio device by adding the
chip->shutdown_mutex and chip->shutdown check at appropriate places.
The spots to put bandaids are:
- PCM prepare, hw_params and hw_free
- where the usb device is accessed for communication or get speed, in
mixer.c and others; the device speed is now cached in subs->speed
instead of accessing to chip->dev
The accesses in PCM open and close don't need the mutex protection
because these are already handled in the core PCM disconnection code.
The autosuspend/autoresume codes are still uncovered by this patch
because of possible mutex deadlocks. They'll be covered by the
upcoming change to rwsem.
Also the mixer codes are untouched, too. These will be fixed in
another patch, too.
Reported-by: Matthieu CASTET <matthieu.castet@parrot.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The variable ep is initialized but never used
otherwise, so remove the unused variable.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The recent fix for USB suspend breakage moved the code to set up EP
from hw_params to prepare, but it means also the EP setup might be
called multiple times unnecessarily because the prepare callback can
be called multiple times without starting the stream (e.g. OSS
emulation).
This patch adds a new flag to struct snd_usb_substream indicating
whether the setup of EP is required, and do it only when necessary,
i.e. right after hw_params or suspend.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Move interface and endpoint configuration from hw_params to prepare
callback. During system suspend/resume when the USB device power isn't
cycled the interface and endpoint configuration need to be set before
audio playback can continue. Resume involves another call to prepare
but not to hw_params, moving it here allows a playing stream to continue
after resume.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Change the interface to configure an endpoint so that it doesn't require
a hw_params struct. This will allow it to be called from prepare
instead of hw_params, configuring it after system resume.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Set the peiod_bytes member of snd_usb_substream. It was no longer being
set, but will be needed to resume properly in a future commit.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The recent fix for the missing fine delayed time adjustment gives
strange error messages at each start of the playback stream, such as
delay: estimated 0, actual 352
delay: estimated 353, actual 705
These come from the sanity check in retire_playback_urb(). Before the
stream is activated via start_endpoints(), a few silent packets have
been already sent. And at this point the delay account is still in
the state as if the new packets are just queued, so the driver gets
confused and spews the bogus error messages.
For fixing the issue, we just need to check whether the received
packet is valid, whether it's zero sized or not.
Reported-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Cc: <stable@vger.kernel.org> [v3.5+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit 68e67f40b ("ALSA: snd-usb: move calls to usb_set_interface")
saved us some unnecessary calls to snd_usb_set_interface() but ignored
the fact that there is at least one device out there which operates on
two endpoint in different interfaces simultaniously.
Take care for this by catching the case where data and sync endpoints
are located on different interfaces and calling snd_usb_set_interface()
between the start of the two endpoints.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reported-by: Robert M. Albrecht <linux@romal.de>
Cc: stable@kernel.org [v3.5+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In order to support devices with implicit feedback streaming models,
packet sizes are now stored with each individual urb, and the PCM
handling code which fills the buffers purely relies on the size fields
now.
However, calling snd_usb_audio_next_packet_size() for all possible
packets in an URB at once, prior to letting the PCM code do its job
does in fact not lead to the same behaviour than what the old code did:
The PCM code will break its loop once a period boundary is reached,
consequently using up less packets that it really could.
As snd_usb_audio_next_packet_size() implements a feedback mechanism to
the endpoints phase accumulator, the number of calls to that function
matters, and when called too often, the data rate runs out of bounds.
Fix this by making the next_packet function public, and call it from the
PCM code as before if the packet data sizes are not defined.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Cc: stable@kernel.org [v3.5+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Parts of commit 294c4fb8 ("ALSA: usb: refine delay information with USB
frame counter") were unfortunately lost during the refactoring of the
snd-usb driver in 3.5.
This patch adds them back, restoring the correct delay information
behaviour.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Cc: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Cc: stable@kernel.org [3.5+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit e9ba389c5 ("ALSA: usb-audio: Fix scheduling-while-atomic bug in
PCM capture stream") fixed a scheduling-while-atomic bug that happened
when snd_usb_endpoint_start was called from the trigger callback, which
is an atmic context. However, the patch breaks the idea of the endpoints
reference counting, which is the reason why the driver has been
refactored lately.
Revert that commit and let snd_usb_endpoint_start() take care of the URB
cancellation again. As this function is called from both atomic and
non-atomic context, add a flag to denote whether the function may sleep.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Cc: stable@kernel.org [3.5+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A PCM capture stream on usb-audio causes a scheduling-while-atomic
BUG, as reported in the bugzilla entry below. It's because
snd_usb_endpoint_start() is called at first at trigger START for a
capture stream, and this function contains the left-over EP
deactivation codes. The problem doesn't happen for a playback stream
because the function is called at PCM prepare time, which can sleep.
This patch fixes the BUG by moving the EP deactivation code into the
PCM prepare callback.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=46011
Cc: <stable@vger.kernel.org> [v3.5+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The rework of the snd-usb endpoint logic moved the calls to
snd_usb_set_interface() into the snd_usb_endpoint implemenation. This
changed the order in which these calls are issued to the device, and
thereby caused regressions for some webcams.
Fix this by moving the calls back to pcm.c for now to make it work again
and use snd_usb_endpoint_activate() to really tear down all remaining
URBs in the flight, consequently fixing another regression caused by USB
packets on the wire after altsetting 0 has been selected.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reported-and-tested-by: Philipp Dreimann <philipp@dreimann.net>
Reported-by: Joseph Salisbury <joseph.salisbury@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In the new PCM streaming logic, the interface number is assigned to
usb stream instance (subs->interface) after the format and rate setups
are succeeded, but some codes are still passing subs->interface as the
reference to helper functions. This leads to initializing with an
invalid iface number (-1).
This patch replaces the wrong references with the ones from the target
fmt correctly.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix a bogus sanity check for sync pipe in pcm.c. This flaw was
introduced during the streaming logic refactorization.
While at it, improve the error messages that are generated in such cases.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reported-and-tested-by: <ben@b1c1l1.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The array of sample rates is reallocated every time when opening
the PCM device, but was freed only once when unplugging the device.
Reported-by: "Alexander E. Patrakov" <patrakov@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Set some substream struct members to make the proc interface code work
again.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reported-by: Felix Homann <linuxaudio@showlabor.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Implicit feedback is a streaming mode that does not rely on dedicated
sync endpoints but uses the information provided by record streams to
clock output streams. Now that the streaming logic is decoupled from the
PCM streams, this is easy to implement.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
With the previous commit that added the new streaming model, all
endpoint and streaming related code is now in endpoint.c, and pcm.c
only acts as a wrapper for handling the packet's payload.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There are certain devices that are reportedly so slow that they need
more than 100 ms to handle control transfers. Therefore, increase the
timeout in mixer(_quirks).c to 1000 ms.
The timeout parameter of snd_usb_ctl_msg() is now constant, so we can
drop it.
Reported-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
No code altered at this point, simply preparing for upcoming
refactorizations.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Existing code only updates the audio delay when URBs were
submitted/retired. This can introduce an uncertainty of 8ms
on the number of samples played out with the default settings,
and a lot more when URBs convey more packets to reduce the
interrupt rate and power consumption.
This patch relies on the USB frame counter to reduce the
uncertainty to less than 2ms worst-case. The delay information
essentially becomes independent of the URB size and number of
packets. This should help applications like PulseAudio which
require accurate audio timing. Clemens Ladisch reported
a decrease of mplayer's A-V difference from nrpacks down to at
most 1ms.
Thanks to Clemens for also pointing out that the implementation
of frame counters varies between different HCDs. Only the
8 lowest-bits are used to estimate the delay.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
[clemens: changed debug code]
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Devices are autosuspended if no pcm nor midi channel is open
Mixer devices may be opened. This way they are active when
in use to play or record sound, but can be suspended while
users have a mixer application running.
[Small clean-ups using static inline by tiwai]
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When a USB audio device is disconnected, snd_usb_audio_disconnect()
kills all audio URBs. At the same time, the application, after being
notified of the disconnection, might close the device, in which case
ALSA calls the .hw_free callback, which should free the URBs too.
Commit de1b8b93a0 "[ALSA] Fix hang-up at disconnection of usb-audio"
prevented snd_usb_hw_free() from freeing the URBs to avoid a hang that
resulted from this race, but this introduced another race because the
URB callbacks could now be executed after snd_usb_hw_free() has
returned, and try to access already freed data.
Fix the first race by introducing a mutex to serialize the disconnect
callback and all PCM callbacks that manage URBs (hw_free and hw_params).
Reported-and-tested-by: Pierre-Louis Bossart <pierre-louis.bossart@intel.com>
Cc: <stable@kernel.org>
[CL: also serialize hw_params callback]
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
sound/usb/pcm.c::snd_usb_pcm_check_knot() fails to check the return value
from kmalloc() and may end up dereferencing a null pointer.
The patch below (compile tested only) should take care of that little
problem.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There are two USB Audio Class specifications (v1 and v2), but neither of
them clearly defines the feedback format for high-speed UAC v1 devices.
Add to this whatever the Creative and M-Audio firmware writers have been
smoking, and it becomes impossible to predict the exact feedback format
used by a particular device.
Therefore, automatically detect the feedback format by looking at the
magnitude of the first received feedback value.
Also, this allows us to get rid of some special cases for E-Mu devices.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Audio Class v2 support code in 2.6.35 added checks for the
bInterfaceProtocol field. However, there are devices (usually those
detected by vendor-specific quirks) that do not have one of the
predefined values in this field, which made the driver reject them.
To fix this regression, restore the old behaviour, i.e., assume that
a device with an unknown bInterfaceProtocol field (other than
UAC_VERSION_2) has more or less UAC-v1-compatible descriptors.
[compile warning fixes by tiwai]
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: Daniel Mack <daniel@caiaq.de>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is V2 of the patch, after feedback from Clemens and Daniel.
This patch adds SuperSpeed support to the USB drivers under sound/. It adds
tests for USB_SPEED_SUPER to the appropriate places that check for the USB
speed.
This patch has been tested with our SS USB3 device emulating a set of Yamaha
speakers and a Logitech microphone, but with the descriptors modified to add
USB3 support. It has also been tested with the real speakers and microphone,
to make sure that USB2 devices still work.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Cc: Clemens Ladisch <clemens@ladisch.de>
Cc: Daniel Mack <daniel@caiaq.de>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Audio devices which comply to the UAC2 standard can export complex clock
topologies in its descriptors and set up links between them.
The entities that are defined are
- clock sources, which define the end-leafs.
- clock selectors, which act as switch to select one out of many
possible clocks sources.
- clock multipliers, which have an input clock source, and act as clock
source again. They can be used to derive one clock from another.
All sample rate changes, clock validity queries and the like must go to
clock source elements, while clock selectors and multipliers can be used
as terminal clock source.
The following patch adds a parser for these elements and functions to
iterate over the tree and find the leaf nodes (clock sources).
The samplerate set functions were moved to the new clock.c file.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This request is again handled differently in comparison to UAC1.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
- Split the audio.h file in two to clearly denote the differences
between the standards.
- Add many more defines to audio-v2.h. Most of them are not currently
used.
- Replaced a magic value with a proper define
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Sample rate setting is done with a 4-byte long class request that
addresses the interface.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In preparation for USB audio 2.0 support, change the audioformat
structure so that it uses a bitmask to specify possible formats.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
