Add a UART 1-Wire bus driver. The driver utilizes the UART interface via
the Serial Device Bus to create the 1-Wire timing patterns. The driver
was tested on a "Raspberry Pi 3B" with a DS18B20 and on a "Variscite
DART-6UL" with a DS18S20 temperature sensor.
The 1-Wire timing pattern and the corresponding UART baud-rate with the
interpretation of the transferred bytes are described in the document:
Link: https://www.analog.com/en/technical-articles/using-a-uart-to-implement-a-1wire-bus-master.html
In short, the UART peripheral must support full-duplex and operate in
open-drain mode. The timing patterns are generated by a specific
combination of baud-rate and transmitted byte, which corresponds to a
1-Wire read bit, write bit or reset.
Signed-off-by: Christoph Winklhofer <cj.winklhofer@gmail.com>
Link: https://lore.kernel.org/r/20240214-w1-uart-v7-3-6e21fa24e066@gmail.com
[krzysztof: w1_uart_serdev_receive_buf() return type fixup]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
w1_therm driver supports now MAX31850, too. Add it to documentation
and fix a small typo.
Signed-off-by: Markus Reichl <m.reichl@fivetechno.de>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
commit c999fbbdcf ("w1: ds2438: support for writing to offset
register") added more documentation, but had a one-off line for the
header of a section which caused the build warning:
Documentation/w1/slaves/w1_ds2438.rst:56: WARNING: Title underline too short.
Resolve this by fixing the underline to be long enough.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Link: https://lore.kernel.org/r/YKthRzCGan9WEcmP@kroah.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Added a sysfs entry to support writing to the offset register on page1.
This register is used to calibrate the chip canceling offset errors in the
current ADC. This means that, over time, reading the IAD register will not
return the correct current measurement, it will have an offset. Writing to
the offset register if the two's complement of the current register while
passing zero current to the load will calibrate the measurements. This
change was tested on real hardware and it was able to calibrate the chip
correctly.
Signed-off-by: Luiz Sampaio <sampaio.ime@gmail.com>
Link: https://lore.kernel.org/r/20210519223046.13798-7-sampaio.ime@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Added a sysfs entry to support reading the page1 registers. This registers
contain Elapsed Time Meter (ETM) data, which shows for how long the chip is
on, as well as an Offset Register data, which can be used to calibrate the
current measurement of the chip.
Signed-off-by: Luiz Sampaio <sampaio.ime@gmail.com>
Link: https://lore.kernel.org/r/20210519223046.13798-6-sampaio.ime@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Duplicate attribute 'eeprom' is defined in:
1) Documentation/ABI/testing/sysfs-driver-w1_therm
2) Documentation/ABI/stable/sysfs-driver-w1_ds28e04
Both drivers define an attribute: /sys/bus/w1/devices/.../eeprom
with conflicting behavior.
Fix by renaming the newer one in w1_therm.c to 'eeprom_cmd'.
Reported-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/lkml/20201029152845.6bbb39ce@coco.lan/
Signed-off-by: Ivan Zaentsev <ivan.zaentsev@wirenboard.ru>
Link: https://lore.kernel.org/r/20201112064931.8471-1-ivan.zaentsev@wirenboard.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
sysfs attribute names are mixed with the same normal text terms.
Use ReST to distinguish.
Fix typos and mistakes.
Reported-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Ivan Zaentsev <ivan.zaentsev@wirenboard.ru>
Link: https://lore.kernel.org/r/20201008054259.5461-1-ivan.zaentsev@wirenboard.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
GX20MH01 device shares family number 0x28 with DS18B20. The device
is generally compatible with DS18B20. Added are the lowest 2^-5, 2^-6
temperature bits in Config register; R2 bit in Config register
enabling 13 and 14 bit resolutions. It is powered up in 14 bit mode.
Signed-off-by: Ivan Zaentsev <ivan.zaentsev@wirenboard.ru>
Link: https://lore.kernel.org/r/20200904160004.87710-2-ivan.zaentsev@wirenboard.ru
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The conversion time of common DS18B20 clones deviates from
datasheet specs. Allow adjustment and automatic measure of the
conversion time.
Add 'conv_time' sysfs attribute:
*read*: Current conversion time in milliseconds.
*write*:
'0': Set default conversion time.
'1': Measure and set the conversion time. Make a
single temperature conversion, poll and measure
an actual value. Measured value is increased
by 20% for temperature drift. A new conversion
time is returned by reading the same attribute.
other positive value:
Set the conversion time in milliseconds.
The setting is active until a resolution change. Then it is reset to
default conversion time for a new resolution.
Add 'features' sysfs attribute to control optional driver settings
per device. Bit masks to read/write (logical OR):
1: Enable check for conversion success. If byte 6 of
scratchpad memory is 0xC after conversion, and
temperature reads 85.00 (powerup value) or 127.94
(insufficient power) - return a conversion error.
2: Enable poll for conversion completion. Generate read cycles
after the conversion start and wait for 1's. In parasite
power mode this feature is not available.
There are some clones of DS18B20 with fixed 12 bit resolution. Make the
driver verify the resolution by reading back the device after resolution
change.
Signed-off-by: Ivan Zaentsev <ivan.zaentsev@wirenboard.ru>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Link: https://lore.kernel.org/r/20200904160004.87710-1-ivan.zaentsev@wirenboard.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adding bulk read support:
Sending a 'trigger' command in the dedicated sysfs entry of bus master
device send a conversion command for all the slaves on the bus. The sysfs
entry is added as soon as at least one device supporting this feature
is detected on the bus.
The behavior of the sysfs reading temperature on the device is as follow:
* If no bulk read pending, trigger a conversion on the device, wait for
the conversion to be done, read the temperature in device RAM
* If a bulk read has been trigger, access directly the device RAM
This behavior is the same on the 2 sysfs entries ('temperature' and
'w1_slave').
Reading the therm_bulk_read sysfs give the status of bulk operations:
* '-1': conversion in progress on at least 1 sensor
* '1': conversion complete but at least one sensor has not been read yet
* '0': no bulk operation. Reading temperature on ecah device will trigger
a conversion
As not all devices support bulk read feature, it has been added in device
family structure.
The attribute is set at master level as soon as a supporting device is
discover. It is removed when the last supported device leave the bus.
The count of supported device is kept with the static counter
bulk_read_device_counter.
A strong pull up is apply on the line if at least one device required it.
The duration of the pull up is the max time required by a device on the
line, which depends on the resolution settings of each device. The strong
pull up could be adjust with the a module parameter.
Updating documentation in Documentation/ABI/testing/sysfs-driver-w1_therm
and Documentation/w1/slaves/w1_therm.rst accordingly.
Signed-off-by: Akira Shimahara <akira215corp@gmail.com>
Link: https://lore.kernel.org/r/20200511203820.411483-1-akira215corp@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ReST directives are introduced with two dots.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The 1wire documentation was written with w1 developers in
mind, so, it makes sense to add it together with the driver-api
set.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
There are lots of documents under Documentation/*.txt and a few other
orphan documents elsehwere that belong to the driver-API book.
Move them to their right place.
Reviewed-by: Cornelia Huck <cohuck@redhat.com> # vfio-related parts
Acked-by: Logan Gunthorpe <logang@deltatee.com> # switchtec
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This is a respin with a wider audience (all that get_maintainer returned)
and I know this spams a *lot* of people. Not sure what would be the correct
way, so my apologies for ruining your inbox.
The 00-INDEX files are supposed to give a summary of all files present
in a directory, but these files are horribly out of date and their
usefulness is brought into question. Often a simple "ls" would reveal
the same information as the filenames are generally quite descriptive as
a short introduction to what the file covers (it should not surprise
anyone what Documentation/sched/sched-design-CFS.txt covers)
A few years back it was mentioned that these files were no longer really
needed, and they have since then grown further out of date, so perhaps
it is time to just throw them out.
A short status yields the following _outdated_ 00-INDEX files, first
counter is files listed in 00-INDEX but missing in the directory, last
is files present but not listed in 00-INDEX.
List of outdated 00-INDEX:
Documentation: (4/10)
Documentation/sysctl: (0/1)
Documentation/timers: (1/0)
Documentation/blockdev: (3/1)
Documentation/w1/slaves: (0/1)
Documentation/locking: (0/1)
Documentation/devicetree: (0/5)
Documentation/power: (1/1)
Documentation/powerpc: (0/5)
Documentation/arm: (1/0)
Documentation/x86: (0/9)
Documentation/x86/x86_64: (1/1)
Documentation/scsi: (4/4)
Documentation/filesystems: (2/9)
Documentation/filesystems/nfs: (0/2)
Documentation/cgroup-v1: (0/2)
Documentation/kbuild: (0/4)
Documentation/spi: (1/0)
Documentation/virtual/kvm: (1/0)
Documentation/scheduler: (0/2)
Documentation/fb: (0/1)
Documentation/block: (0/1)
Documentation/networking: (6/37)
Documentation/vm: (1/3)
Then there are 364 subdirectories in Documentation/ with several files that
are missing 00-INDEX alltogether (and another 120 with a single file and no
00-INDEX).
I don't really have an opinion to whether or not we /should/ have 00-INDEX,
but the above 00-INDEX should either be removed or be kept up to date. If
we should keep the files, I can try to keep them updated, but I rather not
if we just want to delete them anyway.
As a starting point, remove all index-files and references to 00-INDEX and
see where the discussion is going.
Signed-off-by: Henrik Austad <henrik@austad.us>
Acked-by: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Just-do-it-by: Steven Rostedt <rostedt@goodmis.org>
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Acked-by: Paul Moore <paul@paul-moore.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: [Almost everybody else]
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The previous documentation was wrongly stating about the order
of magnitude of CONVERT_V result files contents (vad, vdd).
This commit is correcting this.
Reported-by: Adam Stolarczyk <adam@stolarczyk.net.pl>
Signed-off-by: Mariusz Bialonczyk <manio@skyboo.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
documentation, errseq documentation, kernel-doc support for nested
structure definitions, the removal of lots of crufty kernel-doc support for
unused formats, SPDX tag documentation, the beginnings of a manual for
subsystem maintainers, and lots of fixes and updates.
As usual, some of the changesets reach outside of Documentation/ to effect
kerneldoc comment fixes. It also adds the new LICENSES directory, of which
Thomas promises I do not need to be the maintainer.
-----BEGIN PGP SIGNATURE-----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=Z15Z
-----END PGP SIGNATURE-----
Merge tag 'docs-4.16' of git://git.lwn.net/linux
Pull documentation updates from Jonathan Corbet:
"Documentation updates for 4.16.
New stuff includes refcount_t documentation, errseq documentation,
kernel-doc support for nested structure definitions, the removal of
lots of crufty kernel-doc support for unused formats, SPDX tag
documentation, the beginnings of a manual for subsystem maintainers,
and lots of fixes and updates.
As usual, some of the changesets reach outside of Documentation/ to
effect kerneldoc comment fixes. It also adds the new LICENSES
directory, of which Thomas promises I do not need to be the
maintainer"
* tag 'docs-4.16' of git://git.lwn.net/linux: (65 commits)
linux-next: docs-rst: Fix typos in kfigure.py
linux-next: DOC: HWPOISON: Fix path to debugfs in hwpoison.txt
Documentation: Fix misconversion of #if
docs: add index entry for networking/msg_zerocopy
Documentation: security/credentials.rst: explain need to sort group_list
LICENSES: Add MPL-1.1 license
LICENSES: Add the GPL 1.0 license
LICENSES: Add Linux syscall note exception
LICENSES: Add the MIT license
LICENSES: Add the BSD-3-clause "Clear" license
LICENSES: Add the BSD 3-clause "New" or "Revised" License
LICENSES: Add the BSD 2-clause "Simplified" license
LICENSES: Add the LGPL-2.1 license
LICENSES: Add the LGPL 2.0 license
LICENSES: Add the GPL 2.0 license
Documentation: Add license-rules.rst to describe how to properly identify file licenses
scripts: kernel_doc: better handle show warnings logic
fs/*/Kconfig: drop links to 404-compliant http://acl.bestbits.at
doc: md: Fix a file name to md-fault.c in fault-injection.txt
errseq: Add to documentation tree
...
Onewire devices has 6 byte long unique serial numbers, 1 byte family
code and 1 byte CRC. Linux sysfs presents the device folder in the
form of familyID-deviceID, so CRC is not shown. The consequence is
that the device serial number is always a 12 long hex-string, but
doc says 13 in one place. This is corrected by this change.
Reference: https://en.wikipedia.org/wiki/1-Wire
Signed-off-by: Gergo Huszty <huszty.gergo@digitaltrip.hu>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The w1 master driver includes a complete open drain emulation
reimplementation among other things.
This converts the driver and all board files using it to use
GPIO descriptors associated with the device to look up the
GPIO wire, as well ass the optional pull-up GPIO line.
When probed from the device tree, the driver will just pick
descriptors and use them right off. For the two board files
in the kernel, we add descriptor lookups so we do not need
to keep any old platform data handling around for the GPIO
lines.
As the platform data is also a state container for this driver,
we augment it to contain the GPIO descriptors.
w1_gpio_write_bit_dir() and w1_gpio_write_bit_val() are gone
since this pair was a reimplementation of open drain emulation
which is now handled by gpiolib.
The special "linux,open-drain" flag is a bit of mishap here:
it has the same semantic as the same flags in I2C: it means
that something in the platform is setting up the line as
open drain behind our back. We handle this the same way as
in I2C.
To drive the pull-up, we need to bypass open drain emulation
in gpiolib for the line, and this is done by driving it high
using gpiod_set_raw_value() which has been augmented to have
the semantic of overriding the open drain emulation.
We also augment the documentation to reflect the way to pass
GPIO descriptors from the machine.
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This subpatch adds a driver for the DS28E17 Onewire to I2C master bridge.
Signed-off-by: Jan Kandziora <jjj@gmx.de>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since many temperature sensors come "preconfigured" with a lower
precision, people are stuck at that precision when running on a kernel
based device (unlike the Dallas 1Wire library for e.g. Arduino, which
supports writing the configuration/scratchpad). This patch adds write
support for the scratchpad/precision registers via w1_slave sysfs.
Signed-off-by: Ben Sen <0.x29a.0@gmail.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patches makes following changes to omap_hdq driver
- Enable 1-wire mode.
- Implement w1_triplet callback to facilitate search rom
procedure and auto detection of 1-wire slaves.
- Proper enabling and disabling of interrupt.
- Cleanups (formatting and return value checks).
HDQ mode remains unchanged.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Jonathan Corbet <corbet@lwn.net>
CC: Tony Lindgren <tony@atomide.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: NeilBrown <neilb@suse.de>
Cc: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch provides support for the DS28EA00 digital thermometer.
The DS28EA00 provides an additional two pins for implementing a sequence
detection algorithm. This feature allows you to determine the physical
location of the chip in the 1-wire bus without needing pre-existing
knowledge of the bus ordering. Support is provided through the sysfs
w1_seq file. The file will contain a single line with an integer value
representing the device index in the bus starting at 0.
Signed-off-by: Matt Campbell <mattrcampbell@gmail.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some of 1-Wire devices commonly associated with physical access control
systems are attached/generate presence for as short as 100 ms - hence
the tens-to-hundreds milliseconds scan intervals are required.
Signed-off-by: Dmitry Khromov <dk@icelogic.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some preliminary work at making use of this driver led me to implement
CRC-16 checks on read and write to deal with the occasional glitchiness of
the 1-Wire bus. The revised driver (attached) returns an I/O error if the
CRC check fails. When reading the chip's state, either you get a valid
indication or you get an I/O error. When changing its state, either the
change is successful or an I/O error is returned.
Signed-off-by: Scott Alfter <scott@alfter.us>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Applications can submit a set of commands in one packet to the kernel,
and in some cases it is required such as reading the temperature
sensor results. This adds an option W1_CN_BUNDLE to the flags of
cn_msg to request the kernel to reply in one packet for efficiency.
The cn_msg flags now check for unknown flag values and return an error
if one is seen. See "Proper handling of unknown flags in system
calls" http://lwn.net/Articles/588444/
This corrects the ack values returned as per the protocol standard,
namely the original ack for status messages and seq + 1 for all others
such as the data returned from a read.
Some of the common variable names have been standardized as follows.
struct cn_msg *cn
struct w1_netlink_msg *msg
struct w1_netlink_cmd *cmd
struct w1_master *dev
When an argument and a function scope variable would collide, add req_
to the argument.
Signed-off-by: David Fries <David@Fries.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some of the 00-INDEX files are somewhat outdated and some folders does
not contain 00-INDEX at all. Only outdated (with the notably exception
of spi) indexes are touched here, the 169 folders without 00-INDEX has
not been touched.
New 00-INDEX
- spi/* was added in a series of commits dating back to 2006
Added files (missing in (*/)00-INDEX)
- dmatest.txt was added by commit 851b7e16a0 ("dmatest: run test via
debugfs")
- this_cpu_ops.txt was added by commit a1b2a555d6 ("percpu: add
documentation on this_cpu operations")
- ww-mutex-design.txt was added by commit 040a0a3710 ("mutex: Add
support for wound/wait style locks")
- bcache.txt was added by commit cafe563591 ("bcache: A block layer
cache")
- kernel-per-CPU-kthreads.txt was added by commit 49717cb404
("kthread: Document ways of reducing OS jitter due to per-CPU
kthreads")
- phy.txt was added by commit ff76496347 ("drivers: phy: add generic
PHY framework")
- block/null_blk was added by commit 12f8f4fc03 ("null_blk:
documentation")
- module-signing.txt was added by commit 3cafea3076 ("Add
Documentation/module-signing.txt file")
- assoc_array.txt was added by commit 3cb989501c ("Add a generic
associative array implementation.")
- arm/IXP4xx was part of the initial repo
- arm/cluster-pm-race-avoidance.txt was added by commit 7fe31d28e8
("ARM: mcpm: introduce helpers for platform coherency exit/setup")
- arm/firmware.txt was added by commit 7366b92a77 ("ARM: Add
interface for registering and calling firmware-specific operations")
- arm/kernel_mode_neon.txt was added by commit 2afd0a0524 ("ARM:
7825/1: document the use of NEON in kernel mode")
- arm/tcm.txt was added by commit bc581770cf ("ARM: 5580/2: ARM TCM
(Tightly-Coupled Memory) support v3")
- arm/vlocks.txt was added by commit 9762f12d3e ("ARM: mcpm: Add
baremetal voting mutexes")
- blackfin/gptimers-example.c, Makefile was added by commit
4b60779d5e ("Blackfin: add an example showing how to use the
gptimers API")
- devicetree/usage-model.txt was added by commit 31134efc68 ("dt:
Linux DT usage model documentation")
- fb/api.txt was added by commit fb21c2f428 ("fbdev: Add FOURCC-based
format configuration API")
- fb/sm501.txt was added by commit e6a0498071 ("video, sm501: add
edid and commandline support")
- fb/udlfb.txt was added by commit 96f8d864af ("fbdev: move udlfb out
of staging.")
- filesystems/Makefile was added by commit 1e0051ae48
("Documentation/fs/: split txt and source files")
- filesystems/nfs/nfsd-admin-interfaces.txt was added by commit
8a4c6e19cf ("nfsd: document kernel interfaces for nfsd
configuration")
- ide/warm-plug-howto.txt was added by commit f74c91413e ("ide: add
warm-plug support for IDE devices (take 2)")
- laptops/Makefile was added by commit d49129accc
("Documentation/laptop/: split txt and source files")
- leds/leds-blinkm.txt was added by commit b54cf35a7f ("LEDS: add
BlinkM RGB LED driver, documentation and update MAINTAINERS")
- leds/ledtrig-oneshot.txt was added by commit 5e417281cd ("leds: add
oneshot trigger")
- leds/ledtrig-transient.txt was added by commit 44e1e9f8e7 ("leds:
add new transient trigger for one shot timer activation")
- m68k/README.buddha was part of the initial repo
- networking/LICENSE.(qla3xxx|qlcnic|qlge) was added by commits
40839129f7, c4e84bde1d, 5a4faa8737
- networking/Makefile was added by commit 3794f3e812 ("docsrc: build
Documentation/ sources")
- networking/i40evf.txt was added by commit 105bf2fe6b ("i40evf: add
driver to kernel build system")
- networking/ipsec.txt was added by commit b3c6efbc36 ("xfrm: Add
file to document IPsec corner case")
- networking/mac80211-auth-assoc-deauth.txt was added by commit
3cd7920a2b ("mac80211: add auth/assoc/deauth flow diagram")
- networking/netlink_mmap.txt was added by commit 5683264c39
("netlink: add documentation for memory mapped I/O")
- networking/nf_conntrack-sysctl.txt was added by commit c9f9e0e159
("netfilter: doc: add nf_conntrack sysctl api documentation") lan)
- networking/team.txt was added by commit 3d249d4ca7 ("net: introduce
ethernet teaming device")
- networking/vxlan.txt was added by commit d342894c5d ("vxlan:
virtual extensible lan")
- power/runtime_pm.txt was added by commit 5e928f77a0 ("PM: Introduce
core framework for run-time PM of I/O devices (rev. 17)")
- power/charger-manager.txt was added by commit 3bb3dbbd56
("power_supply: Add initial Charger-Manager driver")
- RCU/lockdep-splat.txt was added by commit d7bd2d68aa ("rcu:
Document interpretation of RCU-lockdep splats")
- s390/kvm.txt was added by 5ecee4b (KVM: s390: API documentation)
- s390/qeth.txt was added by commit b4d72c08b3 ("qeth: bridgeport
support - basic control")
- scheduler/sched-bwc.txt was added by commit 88ebc08ea9 ("sched: Add
documentation for bandwidth control")
- scsi/advansys.txt was added by commit 4bd6d7f356 ("[SCSI] advansys:
Move documentation to Documentation/scsi")
- scsi/bfa.txt was added by commit 1ec90174bd ("[SCSI] bfa: add
readme file")
- scsi/bnx2fc.txt was added by commit 12b8fc10ea ("[SCSI] bnx2fc: Add
driver documentation")
- scsi/cxgb3i.txt was added by commit c3673464eb ("[SCSI] cxgb3i: Add
cxgb3i iSCSI driver.")
- scsi/hpsa.txt was added by commit 992ebcf14f ("[SCSI] hpsa: Add
hpsa.txt to Documentation/scsi")
- scsi/link_power_management_policy.txt was added by commit
ca77329fb7 ("[libata] Link power management infrastructure")
- scsi/osd.txt was added by commit 78e0c621de ("[SCSI] osd:
Documentation for OSD library")
- scsi/scsi-parameter.txt was created/moved by commit 163475fb11
("Documentation: move SCSI parameters to their own text file")
- serial/driver was part of the initial repo
- serial/n_gsm.txt was added by commit 323e84122e ("n_gsm: add a
documentation")
- timers/Makefile was added by commit 3794f3e812 ("docsrc: build
Documentation/ sources")
- virt/kvm/s390.txt was added by commit d9101fca3d ("KVM: s390:
diagnose call documentation")
- vm/split_page_table_lock was added by commit 49076ec2cc ("mm:
dynamically allocate page->ptl if it cannot be embedded to struct
page")
- w1/slaves/w1_ds28e04 was added by commit fbf7f7b4e2 ("w1: Add
1-wire slave device driver for DS28E04-100")
- w1/masters/omap-hdq was added by commit e0a29382c6 ("hdq:
documentation for OMAP HDQ")
- x86/early-microcode.txt was added by commit 0d91ea86a8 ("x86, doc:
Documentation for early microcode loading")
- x86/earlyprintk.txt was added by commit a1aade4788 ("x86/doc:
mini-howto for using earlyprintk=dbgp")
- x86/entry_64.txt was added by commit 8b4777a4b5 ("x86-64: Document
some of entry_64.S")
- x86/pat.txt was added by commit d27554d874 ("x86: PAT
documentation")
Moved files
- arm/kernel_user_helpers.txt was moved out of arch/arm/kernel by
commit 37b8304642 ("ARM: kuser: move interface documentation out of
the source code")
- efi-stub.txt was moved out of x86/ and down into Documentation/ in
commit 4172fe2f8a ("EFI stub documentation updates")
- laptops/hpfall.c was moved out of hwmon/ and into laptops/ in commit
efcfed9bad ("Move hp_accel to drivers/platform/x86")
- commit 5616c23ad9 ("x86: doc: move x86-generic documentation from
Doc/x86/i386"):
* x86/usb-legacy-support.txt
* x86/boot.txt
* x86/zero_page.txt
- power/video_extension.txt was moved to acpi in commit 70e66e4df1
("ACPI / video: move video_extension.txt to Documentation/acpi")
Removed files (left in 00-INDEX)
- memory.txt was removed by commit 00ea8990aa ("memory.txt: remove
stray information")
- gpio.txt was moved to gpio/ in commit fd8e198cfc ("Documentation:
gpiolib: document new interface")
- networking/DLINK.txt was removed by commit 168e06ae26
("drivers/net: delete old parallel port de600/de620 drivers")
- serial/hayes-esp.txt was removed by commit f53a2ade0b ("tty: esp:
remove broken driver")
- s390/TAPE was removed by commit 9e280f6693 ("[S390] remove tape
block docu")
- vm/locking was removed by commit 57ea8171d2 ("mm: documentation:
remove hopelessly out-of-date locking doc")
- laptops/acer-wmi.txt was remvoed by commit 020036678e ("acer-wmi:
Delete out-of-date documentation")
Typos/misc issues
- rpc-server-gss.txt was added as knfsd-rpcgss.txt in commit
030d794bf4 ("SUNRPC: Use gssproxy upcall for server RPCGSS
authentication.")
- commit b88cf73d92 ("net: add missing entries to
Documentation/networking/00-INDEX")
* generic-hdlc.txt was added as generic_hdlc.txt
* spider_net.txt was added as spider-net.txt
- w1/master/mxc-w1 was added as mxc_w1 by commit a5fd9139f7 ("w1: add
1-wire master driver for i.MX27 / i.MX31")
- s390/zfcpdump.txt was added as zfcpdump by commit 6920c12a40
("[S390] Add Documentation/s390/00-INDEX.")
Signed-off-by: Henrik Austad <henrik@austad.us>
Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> [rcu bits]
Acked-by: Rob Landley <rob@landley.net>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Mark Brown <broonie@kernel.org>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Len Brown <len.brown@intel.com>
Cc: James Bottomley <JBottomley@parallels.com>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Switch the code documentation format style to DocBook format, enable
DocBook documentation generation, and fix some comments.
Signed-off-by: David Fries <David@Fries.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The hardware search was failing without the COMM_RST flag. Enabled
the flag and rewrote the function to handle more than one buffer of
results and to continuing where the search left off. Remove hardware
search note from the limitations now that it works. The "w1: ds2490
USB setup fixes" change went from 23.16 seconds to about 3 seconds,
this takes the time for the search down to .307346 seconds.
Signed-off-by: David Fries <David@Fries.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull trivial tree updates from Jiri Kosina:
"The usual stuff from trivial tree"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (34 commits)
treewide: relase -> release
Documentation/cgroups/memory.txt: fix stat file documentation
sysctl/net.txt: delete reference to obsolete 2.4.x kernel
spinlock_api_smp.h: fix preprocessor comments
treewide: Fix typo in printk
doc: device tree: clarify stuff in usage-model.txt.
open firmware: "/aliasas" -> "/aliases"
md: bcache: Fixed a typo with the word 'arithmetic'
irq/generic-chip: fix a few kernel-doc entries
frv: Convert use of typedef ctl_table to struct ctl_table
sgi: xpc: Convert use of typedef ctl_table to struct ctl_table
doc: clk: Fix incorrect wording
Documentation/arm/IXP4xx fix a typo
Documentation/networking/ieee802154 fix a typo
Documentation/DocBook/media/v4l fix a typo
Documentation/video4linux/si476x.txt fix a typo
Documentation/virtual/kvm/api.txt fix a typo
Documentation/early-userspace/README fix a typo
Documentation/video4linux/soc-camera.txt fix a typo
lguest: fix CONFIG_PAE -> CONFIG_x86_PAE in comment
...
This patch allows the 1-wire bus to autoload the corresponding module
for each slave being attached.
This works similar to bluetooth protocols.
Signed-off-by: Alexander Stein <alexander.stein@informatik.tu-chemnitz.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for maxim ds1825 based 1-wire temperature sensors.
Signed-off-by: Raphael Assenat <raph@8d.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Below you will find an updated version from the original series bunching all patches into one big patch
updating broken web addresses that are located in Documentation/*
Some of the addresses date as far far back as 1995 etc... so searching became a bit difficult,
the best way to deal with these is to use web.archive.org to locate these addresses that are outdated.
Now there are also some addresses pointing to .spec files some are located, but some(after searching
on the companies site)where still no where to be found. In this case I just changed the address
to the company site this way the users can contact the company and they can locate them for the users.
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Cc: Paulo Marques <pmarques@grupopie.com>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Cc: Michael Neuling <mikey@neuling.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Fix obvious cases of "it's" being used when "its" was meant.
Signed-off-by: Francis Galiegue <fgaliegue@gmail.com>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
There is no point in implementing a detect callback for the DS2482, as
this device can't be detected. It was there solely to handle "force"
module parameters to instantiate devices, but now we have a better sysfs
interface that can do the same.
So we can get rid of the ugly module parameters and the detect callback.
This shrinks the binary module size by 21%.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Ben Gardner <gardner.ben@gmail.com>
Send completion status of the commands to the userspace. Message and
protocol are described in the documentation.
Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Paul Alfille <paul.alfille@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Command which allows to reset the bus.
Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Paul Alfille <paul.alfille@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds support for the 1-wire master interface for i.MX27 and
i.MX31.
Signed-off-by: Luotao Fu <l.fu@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
