commit cb8b02fd63 upstream.
There are two ways that special characters (not allowed in some
other operating systems like Windows, but allowed in POSIX) have
been mapped in the past ("SFU" and "SFM" mappings) to allow them
to be stored in a range reserved for special chars. The default
for Linux has been to use "mapposix" (ie the SFM mapping) but
the conversion to the new mount API in the 5.11 kernel broke
the ability to override the default mapping of the reserved
characters (like '?' and '*' and '\') via "mapchars" mount option.
This patch fixes that - so can now mount with "mapchars"
mount option to override the default ("mapposix" ie SFM) mapping.
Reported-by: Tyler Spivey <tspivey8@gmail.com>
Fixes: 24e0a1eff9 ("cifs: switch to new mount api")
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 878ecb0897 upstream.
optlen is fetched without checking whether there is more than one byte to parse.
It can lead to out-of-bounds access.
Found by InfoTeCS on behalf of Linux Verification Center
(linuxtesting.org) with SVACE.
Fixes: c61a404325 ("[IPV6]: Find option offset by type.")
Signed-off-by: Gavrilov Ilia <Ilia.Gavrilov@infotecs.ru>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0613d8ca9a upstream.
A narrow load from a 64-bit context field results in a 64-bit load
followed potentially by a 64-bit right-shift and then a bitwise AND
operation to extract the relevant data.
In the case of a 32-bit access, an immediate mask of 0xffffffff is used
to construct a 64-bit BPP_AND operation which then sign-extends the mask
value and effectively acts as a glorified no-op. For example:
0: 61 10 00 00 00 00 00 00 r0 = *(u32 *)(r1 + 0)
results in the following code generation for a 64-bit field:
ldr x7, [x7] // 64-bit load
mov x10, #0xffffffffffffffff
and x7, x7, x10
Fix the mask generation so that narrow loads always perform a 32-bit AND
operation:
ldr x7, [x7] // 64-bit load
mov w10, #0xffffffff
and w7, w7, w10
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: John Fastabend <john.fastabend@gmail.com>
Cc: Krzesimir Nowak <krzesimir@kinvolk.io>
Cc: Andrey Ignatov <rdna@fb.com>
Acked-by: Yonghong Song <yhs@fb.com>
Fixes: 31fd85816d ("bpf: permits narrower load from bpf program context fields")
Signed-off-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20230518102528.1341-1-will@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d226b1df36 upstream.
In the end of the test, there will be an error message induced by the
`ip netns del ns1` command in cleanup()
Tests passed: 201
Tests failed: 0
Cannot remove namespace file "/run/netns/ns1": No such file or directory
This can even be reproduced with just `./fib_tests.sh -h` as we're
calling cleanup() on exit.
Redirect the error message to /dev/null to mute it.
V2: Update commit message and fixes tag.
V3: resubmit due to missing netdev ML in V2
Fixes: b60417a9f2 ("selftest: fib_tests: Always cleanup before exit")
Signed-off-by: Po-Hsu Lin <po-hsu.lin@canonical.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8a02fb71d7 upstream.
Commit 50749f2dd6 ("tcp/udp: Fix memleaks of sk and zerocopy skbs with
TX timestamp.") added a call to skb_orphan_frags_rx() to fix leaks with
zerocopy skbs. But it ended up adding a leak of its own. When
skb_orphan_frags_rx() fails, the function just returns, leaking the skb
it just cloned. Free it before returning.
This bug was discovered and resolved using Coverity Static Analysis
Security Testing (SAST) by Synopsys, Inc.
Fixes: 50749f2dd6 ("tcp/udp: Fix memleaks of sk and zerocopy skbs with TX timestamp.")
Signed-off-by: Pratyush Yadav <ptyadav@amazon.de>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://lore.kernel.org/r/20230522153020.32422-1-ptyadav@amazon.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 75e5fab7db upstream.
When we run syzkaller we get below Out of Bounds error.
"KASAN: slab-out-of-bounds Read in regcache_flat_read"
Below is the backtrace of the issue:
BUG: KASAN: slab-out-of-bounds in regcache_flat_read+0x10c/0x110
Read of size 4 at addr ffffff8088fbf714 by task syz-executor.4/14144
CPU: 6 PID: 14144 Comm: syz-executor.4 Tainted: G W
Hardware name: Qualcomm Technologies, Inc. sc7280 CRD platform (rev5+) (DT)
Call trace:
dump_backtrace+0x0/0x4ec
show_stack+0x34/0x50
dump_stack_lvl+0xdc/0x11c
print_address_description+0x30/0x2d8
kasan_report+0x178/0x1e4
__asan_report_load4_noabort+0x44/0x50
regcache_flat_read+0x10c/0x110
regcache_read+0xf8/0x5a0
_regmap_read+0x45c/0x86c
_regmap_update_bits+0x128/0x290
regmap_update_bits_base+0xc0/0x15c
snd_soc_component_update_bits+0xa8/0x22c
snd_soc_component_write_field+0x68/0xd4
tx_macro_put_dec_enum+0x1d0/0x268
snd_ctl_elem_write+0x288/0x474
By Error checking and checking valid values issue gets rectifies.
Signed-off-by: Ravulapati Vishnu Vardhan Rao <quic_visr@quicinc.com
Link: https://lore.kernel.org/r/20230511112532.16106-1-quic_visr@quicinc.com
Signed-off-by: Mark Brown <broonie@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1389062650 upstream.
Many of the older USB drivers in the Linux USB stack were written
based simply on a vendor's device specification. They use the
endpoint information in the spec and assume these endpoints will
always be present, with the properties listed, in any device matching
the given vendor and product IDs.
While that may have been true back then, with spoofing and fuzzing it
is not true any more. More and more we are finding that those old
drivers need to perform at least a minimum of checking before they try
to use any endpoint other than ep0.
To make this checking as simple as possible, we now add a couple of
utility routines to the USB core. usb_check_bulk_endpoints() and
usb_check_int_endpoints() take an interface pointer together with a
list of endpoint addresses (numbers and directions). They check that
the interface's current alternate setting includes endpoints with
those addresses and that each of these endpoints has the right type:
bulk or interrupt, respectively.
Although we already have usb_find_common_endpoints() and related
routines meant for a similar purpose, they are not well suited for
this kind of checking. Those routines find endpoints of various
kinds, but only one (either the first or the last) of each kind, and
they don't verify that the endpoints' addresses agree with what the
caller expects.
In theory the new routines could be more general: They could take a
particular altsetting as their argument instead of always using the
interface's current altsetting. In practice I think this won't matter
too much; multiple altsettings tend to be used for transferring media
(audio or visual) over isochronous endpoints, not bulk or interrupt.
Drivers for such devices will generally require more sophisticated
checking than these simplistic routines provide.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/dd2c8e8c-2c87-44ea-ba17-c64b97e201c9@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ae9b15fbe6 upstream.
When the virtual interface's feature is updated, it synchronizes the
updated feature for its own lower interface.
This propagation logic should be worked as the iteration, not recursively.
But it works recursively due to the netdev notification unexpectedly.
This problem occurs when it disables LRO only for the team and bonding
interface type.
team0
|
+------+------+-----+-----+
| | | | |
team1 team2 team3 ... team200
If team0's LRO feature is updated, it generates the NETDEV_FEAT_CHANGE
event to its own lower interfaces(team1 ~ team200).
It is worked by netdev_sync_lower_features().
So, the NETDEV_FEAT_CHANGE notification logic of each lower interface
work iteratively.
But generated NETDEV_FEAT_CHANGE event is also sent to the upper
interface too.
upper interface(team0) generates the NETDEV_FEAT_CHANGE event for its own
lower interfaces again.
lower and upper interfaces receive this event and generate this
event again and again.
So, the stack overflow occurs.
But it is not the infinite loop issue.
Because the netdev_sync_lower_features() updates features before
generating the NETDEV_FEAT_CHANGE event.
Already synchronized lower interfaces skip notification logic.
So, it is just the problem that iteration logic is changed to the
recursive unexpectedly due to the notification mechanism.
Reproducer:
ip link add team0 type team
ethtool -K team0 lro on
for i in {1..200}
do
ip link add team$i master team0 type team
ethtool -K team$i lro on
done
ethtool -K team0 lro off
In order to fix it, the notifier_ctx member of bonding/team is introduced.
Reported-by: syzbot+60748c96cf5c6df8e581@syzkaller.appspotmail.com
Fixes: fd867d51f8 ("net/core: generic support for disabling netdev features down stack")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://lore.kernel.org/r/20230517143010.3596250-1-ap420073@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ed9de4ed39 upstream.
The syzbot fuzzer detected a problem in the udlfb driver, caused by an
endpoint not having the expected type:
usb 1-1: Read EDID byte 0 failed: -71
usb 1-1: Unable to get valid EDID from device/display
------------[ cut here ]------------
usb 1-1: BOGUS urb xfer, pipe 3 != type 1
WARNING: CPU: 0 PID: 9 at drivers/usb/core/urb.c:504 usb_submit_urb+0xed6/0x1880
drivers/usb/core/urb.c:504
Modules linked in:
CPU: 0 PID: 9 Comm: kworker/0:1 Not tainted
6.4.0-rc1-syzkaller-00016-ga4422ff22142 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google
04/28/2023
Workqueue: usb_hub_wq hub_event
RIP: 0010:usb_submit_urb+0xed6/0x1880 drivers/usb/core/urb.c:504
...
Call Trace:
<TASK>
dlfb_submit_urb+0x92/0x180 drivers/video/fbdev/udlfb.c:1980
dlfb_set_video_mode+0x21f0/0x2950 drivers/video/fbdev/udlfb.c:315
dlfb_ops_set_par+0x2a7/0x8d0 drivers/video/fbdev/udlfb.c:1111
dlfb_usb_probe+0x149a/0x2710 drivers/video/fbdev/udlfb.c:1743
The current approach for this issue failed to catch the problem
because it only checks for the existence of a bulk-OUT endpoint; it
doesn't check whether this endpoint is the one that the driver will
actually use.
We can fix the problem by instead checking that the endpoint used by
the driver does exist and is bulk-OUT.
Reported-and-tested-by: syzbot+0e22d63dcebb802b9bc8@syzkaller.appspotmail.com
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Pavel Skripkin <paskripkin@gmail.com>
Fixes: aaf7dbe073 ("video: fbdev: udlfb: properly check endpoint type")
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eb799279fb upstream.
syzbot is reporting a lockdep warning in fill_pool() because the allocation
from debugobjects is using GFP_ATOMIC, which is (__GFP_HIGH | __GFP_KSWAPD_RECLAIM)
and therefore tries to wake up kswapd, which acquires kswapd_wait::lock.
Since fill_pool() might be called with arbitrary locks held, fill_pool()
should not assume that acquiring kswapd_wait::lock is safe.
Use __GFP_HIGH instead and remove __GFP_NORETRY as it is pointless for
!__GFP_DIRECT_RECLAIM allocation.
Fixes: 3ac7fe5a4a ("infrastructure to debug (dynamic) objects")
Reported-by: syzbot <syzbot+fe0c72f0ccbb93786380@syzkaller.appspotmail.com>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/6577e1fa-b6ee-f2be-2414-a2b51b1c5e30@I-love.SAKURA.ne.jp
Closes: https://syzkaller.appspot.com/bug?extid=fe0c72f0ccbb93786380
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit edc0a2b595 upstream.
Traditionally, all CPUs in a system have identical numbers of SMT
siblings. That changes with hybrid processors where some logical CPUs
have a sibling and others have none.
Today, the CPU boot code sets the global variable smp_num_siblings when
every CPU thread is brought up. The last thread to boot will overwrite
it with the number of siblings of *that* thread. That last thread to
boot will "win". If the thread is a Pcore, smp_num_siblings == 2. If it
is an Ecore, smp_num_siblings == 1.
smp_num_siblings describes if the *system* supports SMT. It should
specify the maximum number of SMT threads among all cores.
Ensure that smp_num_siblings represents the system-wide maximum number
of siblings by always increasing its value. Never allow it to decrease.
On MeteorLake-P platform, this fixes a problem that the Ecore CPUs are
not updated in any cpu sibling map because the system is treated as an
UP system when probing Ecore CPUs.
Below shows part of the CPU topology information before and after the
fix, for both Pcore and Ecore CPU (cpu0 is Pcore, cpu 12 is Ecore).
...
-/sys/devices/system/cpu/cpu0/topology/package_cpus:000fff
-/sys/devices/system/cpu/cpu0/topology/package_cpus_list:0-11
+/sys/devices/system/cpu/cpu0/topology/package_cpus:3fffff
+/sys/devices/system/cpu/cpu0/topology/package_cpus_list:0-21
...
-/sys/devices/system/cpu/cpu12/topology/package_cpus:001000
-/sys/devices/system/cpu/cpu12/topology/package_cpus_list:12
+/sys/devices/system/cpu/cpu12/topology/package_cpus:3fffff
+/sys/devices/system/cpu/cpu12/topology/package_cpus_list:0-21
Notice that the "before" 'package_cpus_list' has only one CPU. This
means that userspace tools like lscpu will see a little laptop like
an 11-socket system:
-Core(s) per socket: 1
-Socket(s): 11
+Core(s) per socket: 16
+Socket(s): 1
This is also expected to make the scheduler do rather wonky things
too.
[ dhansen: remove CPUID detail from changelog, add end user effects ]
CC: stable@kernel.org
Fixes: bbb65d2d36 ("x86: use cpuid vector 0xb when available for detecting cpu topology")
Fixes: 95f3d39ccf ("x86/cpu/topology: Provide detect_extended_topology_early()")
Suggested-by: Len Brown <len.brown@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/all/20230323015640.27906-1-rui.zhang%40intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 38776cc45e upstream.
The number of CHAs from the discovery table on some SPR variants is
incorrect, because of a firmware issue. An accurate number can be read
from the MSR UNC_CBO_CONFIG.
Fixes: 949b11381f ("perf/x86/intel/uncore: Add Sapphire Rapids server CHA support")
Reported-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Stephane Eranian <eranian@google.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230508140206.283708-1-kan.liang@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 61e150fb31 upstream.
Since at least kernel 6.1, flush_dcache_page() is called with IRQs
disabled, e.g. from aio_complete().
But the current implementation for flush_dcache_page() on parisc
unintentionally re-enables IRQs, which may lead to deadlocks.
Fix it by using xa_lock_irqsave() and xa_unlock_irqrestore()
for the flush_dcache_mmap_*lock() macros instead.
Cc: linux-parisc@vger.kernel.org
Cc: stable@kernel.org # 5.18+
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Partially backport v6.3 commit 11f75a0144 ("selftests/memfd: add tests
for MFD_NOEXEC_SEAL MFD_EXEC") to fix an unknown type name build error.
In some systems, the __u64 typedef is not present due to differences in
system headers, causing compilation errors like this one:
fuse_test.c:64:8: error: unknown type name '__u64'
64 | static __u64 mfd_assert_get_seals(int fd)
This header includes the __u64 typedef which increases the likelihood
of successful compilation on a wider variety of systems.
Signed-off-by: Hardik Garg <hargar@linux.microsoft.com>
Reviewed-by: Tyler Hicks (Microsoft) <code@tyhicks.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ce0b15d11a upstream.
The INVLPG instruction is used to invalidate TLB entries for a
specified virtual address. When PCIDs are enabled, INVLPG is supposed
to invalidate TLB entries for the specified address for both the
current PCID *and* Global entries. (Note: Only kernel mappings set
Global=1.)
Unfortunately, some INVLPG implementations can leave Global
translations unflushed when PCIDs are enabled.
As a workaround, never enable PCIDs on affected processors.
I expect there to eventually be microcode mitigations to replace this
software workaround. However, the exact version numbers where that
will happen are not known today. Once the version numbers are set in
stone, the processor list can be tweaked to only disable PCIDs on
affected processors with affected microcode.
Note: if anyone wants a quick fix that doesn't require patching, just
stick 'nopcid' on your kernel command-line.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Sneddon <daniel.sneddon@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 50a1726b14 upstream.
In cdns3-gadget.c, 'cdns,on-chip-buff-size' was read using
device_property_read_u16(). It resulted in 0 if a 32bit value was used
in dts. This commit fixes the dt binding doc to declare it as u16.
Cc: stable@vger.kernel.org
Fixes: 68989fe1c3 ("dt-bindings: usb: Convert cdns-usb3.txt to YAML schema")
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 597441b343 upstream.
Our CI system caught a lockdep splat:
======================================================
WARNING: possible circular locking dependency detected
6.3.0-rc7+ #1167 Not tainted
------------------------------------------------------
kswapd0/46 is trying to acquire lock:
ffff8c6543abd650 (sb_internal#2){++++}-{0:0}, at: btrfs_commit_inode_delayed_inode+0x5f/0x120
but task is already holding lock:
ffffffffabe61b40 (fs_reclaim){+.+.}-{0:0}, at: balance_pgdat+0x4aa/0x7a0
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (fs_reclaim){+.+.}-{0:0}:
fs_reclaim_acquire+0xa5/0xe0
kmem_cache_alloc+0x31/0x2c0
alloc_extent_state+0x1d/0xd0
__clear_extent_bit+0x2e0/0x4f0
try_release_extent_mapping+0x216/0x280
btrfs_release_folio+0x2e/0x90
invalidate_inode_pages2_range+0x397/0x470
btrfs_cleanup_dirty_bgs+0x9e/0x210
btrfs_cleanup_one_transaction+0x22/0x760
btrfs_commit_transaction+0x3b7/0x13a0
create_subvol+0x59b/0x970
btrfs_mksubvol+0x435/0x4f0
__btrfs_ioctl_snap_create+0x11e/0x1b0
btrfs_ioctl_snap_create_v2+0xbf/0x140
btrfs_ioctl+0xa45/0x28f0
__x64_sys_ioctl+0x88/0xc0
do_syscall_64+0x38/0x90
entry_SYSCALL_64_after_hwframe+0x72/0xdc
-> #0 (sb_internal#2){++++}-{0:0}:
__lock_acquire+0x1435/0x21a0
lock_acquire+0xc2/0x2b0
start_transaction+0x401/0x730
btrfs_commit_inode_delayed_inode+0x5f/0x120
btrfs_evict_inode+0x292/0x3d0
evict+0xcc/0x1d0
inode_lru_isolate+0x14d/0x1e0
__list_lru_walk_one+0xbe/0x1c0
list_lru_walk_one+0x58/0x80
prune_icache_sb+0x39/0x60
super_cache_scan+0x161/0x1f0
do_shrink_slab+0x163/0x340
shrink_slab+0x1d3/0x290
shrink_node+0x300/0x720
balance_pgdat+0x35c/0x7a0
kswapd+0x205/0x410
kthread+0xf0/0x120
ret_from_fork+0x29/0x50
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(fs_reclaim);
lock(sb_internal#2);
lock(fs_reclaim);
lock(sb_internal#2);
*** DEADLOCK ***
3 locks held by kswapd0/46:
#0: ffffffffabe61b40 (fs_reclaim){+.+.}-{0:0}, at: balance_pgdat+0x4aa/0x7a0
#1: ffffffffabe50270 (shrinker_rwsem){++++}-{3:3}, at: shrink_slab+0x113/0x290
#2: ffff8c6543abd0e0 (&type->s_umount_key#44){++++}-{3:3}, at: super_cache_scan+0x38/0x1f0
stack backtrace:
CPU: 0 PID: 46 Comm: kswapd0 Not tainted 6.3.0-rc7+ #1167
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.13.0-2.fc32 04/01/2014
Call Trace:
<TASK>
dump_stack_lvl+0x58/0x90
check_noncircular+0xd6/0x100
? save_trace+0x3f/0x310
? add_lock_to_list+0x97/0x120
__lock_acquire+0x1435/0x21a0
lock_acquire+0xc2/0x2b0
? btrfs_commit_inode_delayed_inode+0x5f/0x120
start_transaction+0x401/0x730
? btrfs_commit_inode_delayed_inode+0x5f/0x120
btrfs_commit_inode_delayed_inode+0x5f/0x120
btrfs_evict_inode+0x292/0x3d0
? lock_release+0x134/0x270
? __pfx_wake_bit_function+0x10/0x10
evict+0xcc/0x1d0
inode_lru_isolate+0x14d/0x1e0
__list_lru_walk_one+0xbe/0x1c0
? __pfx_inode_lru_isolate+0x10/0x10
? __pfx_inode_lru_isolate+0x10/0x10
list_lru_walk_one+0x58/0x80
prune_icache_sb+0x39/0x60
super_cache_scan+0x161/0x1f0
do_shrink_slab+0x163/0x340
shrink_slab+0x1d3/0x290
shrink_node+0x300/0x720
balance_pgdat+0x35c/0x7a0
kswapd+0x205/0x410
? __pfx_autoremove_wake_function+0x10/0x10
? __pfx_kswapd+0x10/0x10
kthread+0xf0/0x120
? __pfx_kthread+0x10/0x10
ret_from_fork+0x29/0x50
</TASK>
This happens because when we abort the transaction in the transaction
commit path we call invalidate_inode_pages2_range on our block group
cache inodes (if we have space cache v1) and any delalloc inodes we may
have. The plain invalidate_inode_pages2_range() call passes through
GFP_KERNEL, which makes sense in most cases, but not here. Wrap these
two invalidate callees with memalloc_nofs_save/memalloc_nofs_restore to
make sure we don't end up with the fs reclaim dependency under the
transaction dependency.
CC: stable@vger.kernel.org # 4.14+
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0a1bb16e0f upstream.
This driver's debugfs files have had a read operation since commit
2a9e27408e ("gpio: mockup: rework debugfs interface"), but were
still being created with write-only mode bits. Update them to
indicate that the files can also be read.
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Fixes: 2a9e27408e ("gpio: mockup: rework debugfs interface")
Cc: stable@kernel.org # v5.1+
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2028315cf5 upstream.
In case a machine can't power-off itself on system shutdown,
allow the user to reboot it by pressing the RETURN key.
Cc: <stable@vger.kernel.org> # v4.14+
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6888ff04e3 upstream.
The kernel kgdb break instructions should only be handled when running
in kernel context.
Cc: <stable@vger.kernel.org> # v5.4+
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b845b574f8 upstream.
On 68030/020, an instruction such as, moveml %a2-%a3/%a5,%sp@- may cause
a stack page fault during instruction execution (i.e. not at an
instruction boundary) and produce a format 0xB exception frame.
In this situation, the value of USP will be unreliable. If a signal is
to be delivered following the exception, this USP value is used to
calculate the location for a signal frame. This can result in a
corrupted user stack.
The corruption was detected in dash (actually in glibc) where it showed
up as an intermittent "stack smashing detected" message and crash
following signal delivery for SIGCHLD.
It was hard to reproduce that failure because delivery of the signal
raced with the page fault and because the kernel places an unpredictable
gap of up to 7 bytes between the USP and the signal frame.
A format 0xB exception frame can be produced by a bus error or an
address error. The 68030 Users Manual says that address errors occur
immediately upon detection during instruction prefetch. The instruction
pipeline allows prefetch to overlap with other instructions, which means
an address error can arise during the execution of a different
instruction. So it seems likely that this patch may help in the address
error case also.
Reported-and-tested-by: Stan Johnson <userm57@yahoo.com>
Link: https://lore.kernel.org/all/CAMuHMdW3yD22_ApemzW_6me3adq6A458u1_F0v-1EYwK_62jPA@mail.gmail.com/
Cc: Michael Schmitz <schmitzmic@gmail.com>
Cc: Andreas Schwab <schwab@linux-m68k.org>
Cc: stable@vger.kernel.org
Co-developed-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Finn Thain <fthain@linux-m68k.org>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/r/9e66262a754fcba50208aa424188896cc52a1dd1.1683365892.git.fthain@linux-m68k.org
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7e01c7f704 upstream.
Currently in cdc_ncm_check_tx_max(), if dwNtbOutMaxSize is lower than
the calculated "min" value, but greater than zero, the logic sets
tx_max to dwNtbOutMaxSize. This is then used to allocate a new SKB in
cdc_ncm_fill_tx_frame() where all the data is handled.
For small values of dwNtbOutMaxSize the memory allocated during
alloc_skb(dwNtbOutMaxSize, GFP_ATOMIC) will have the same size, due to
how size is aligned at alloc time:
size = SKB_DATA_ALIGN(size);
size += SKB_DATA_ALIGN(sizeof(struct skb_shared_info));
Thus we hit the same bug that we tried to squash with
commit 2be6d4d16a ("net: cdc_ncm: Allow for dwNtbOutMaxSize to be unset or zero")
Low values of dwNtbOutMaxSize do not cause an issue presently because at
alloc_skb() time more memory (512b) is allocated than required for the
SKB headers alone (320b), leaving some space (512b - 320b = 192b)
for CDC data (172b).
However, if more elements (for example 3 x u64 = [24b]) were added to
one of the SKB header structs, say 'struct skb_shared_info',
increasing its original size (320b [320b aligned]) to something larger
(344b [384b aligned]), then suddenly the CDC data (172b) no longer
fits in the spare SKB data area (512b - 384b = 128b).
Consequently the SKB bounds checking semantics fails and panics:
skbuff: skb_over_panic: text:ffffffff831f755b len:184 put:172 head:ffff88811f1c6c00 data:ffff88811f1c6c00 tail:0xb8 end:0x80 dev:<NULL>
------------[ cut here ]------------
kernel BUG at net/core/skbuff.c:113!
invalid opcode: 0000 [#1] PREEMPT SMP KASAN
CPU: 0 PID: 57 Comm: kworker/0:2 Not tainted 5.15.106-syzkaller-00249-g19c0ed55a470 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 04/14/2023
Workqueue: mld mld_ifc_work
RIP: 0010:skb_panic net/core/skbuff.c:113 [inline]
RIP: 0010:skb_over_panic+0x14c/0x150 net/core/skbuff.c:118
[snip]
Call Trace:
<TASK>
skb_put+0x151/0x210 net/core/skbuff.c:2047
skb_put_zero include/linux/skbuff.h:2422 [inline]
cdc_ncm_ndp16 drivers/net/usb/cdc_ncm.c:1131 [inline]
cdc_ncm_fill_tx_frame+0x11ab/0x3da0 drivers/net/usb/cdc_ncm.c:1308
cdc_ncm_tx_fixup+0xa3/0x100
Deal with too low values of dwNtbOutMaxSize, clamp it in the range
[USB_CDC_NCM_NTB_MIN_OUT_SIZE, CDC_NCM_NTB_MAX_SIZE_TX]. We ensure
enough data space is allocated to handle CDC data by making sure
dwNtbOutMaxSize is not smaller than USB_CDC_NCM_NTB_MIN_OUT_SIZE.
Fixes: 289507d336 ("net: cdc_ncm: use sysfs for rx/tx aggregation tuning")
Cc: stable@vger.kernel.org
Reported-by: syzbot+9f575a1f15fc0c01ed69@syzkaller.appspotmail.com
Link: https://syzkaller.appspot.com/bug?extid=b982f1059506db48409d
Link: https://lore.kernel.org/all/20211202143437.1411410-1-lee.jones@linaro.org/
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230517133808.1873695-2-tudor.ambarus@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8b271370e9 upstream.
The rt5682 driver switches its regmap to cache-only when the
device suspends and back to regular mode on resume. When the
jack detect interrupt fires rt5682_irq() schedules the jack
detect work. This can result in invalid reads from the regmap
in cache-only mode if the work runs before the device has
resumed:
[ 56.245502] rt5682 9-001a: ASoC: error at soc_component_read_no_lock on rt5682.9-001a for register: [0x000000f0] -16
Disable the jack detection interrupt during suspend and
re-enable it on resume. The driver already schedules the
jack detection work on resume, so any state change during
suspend is still handled.
This is essentially the same as commit f7d00a9be1 ("SoC:
rt5682s: Disable jack detection interrupt during suspend")
for the rt5682s.
Cc: stable@kernel.org
Signed-off-by: Matthias Kaehlcke <mka@chromium.org
Reviewed-by: Douglas Anderson <dianders@chromium.org
Reviewed-by: Stephen Boyd <swboyd@chromium.org
Link: https://lore.kernel.org/r/20230516164629.1.Ibf79e94b3442eecc0054d2b478779cc512d967fc@changeid
Signed-off-by: Mark Brown <broonie@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 81dce1490e upstream.
After commit 1ed5c3b22f ("mmc: sdhci-esdhc-imx: Propagate
ESDHC_FLAG_HS400* only on 8bit bus"), the property "no-mmc-hs400"
from device tree file do not work any more.
This patch reorder the code, which can avoid the warning message
"drop HS400 support since no 8-bit bus" and also make the property
"no-mmc-hs400" from dts file works.
Fixes: 1ed5c3b22f ("mmc: sdhci-esdhc-imx: Propagate ESDHC_FLAG_HS400* only on 8bit bus")
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230504112222.3599602-1-haibo.chen@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4ca110cab4 upstream.
Lenovo M70/M90 Gen4 are equipped with ALC897, and they need
ALC897_FIXUP_HEADSET_MIC_PIN quirk to make its headset mic work.
The previous quirk for M70/M90 is for Gen3.
Signed-off-by: Bin Li <bin.li@canonical.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20230524113755.1346928-1-bin.li@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 81302b1c7c upstream.
It's reported that the recording started right after the driver probe
doesn't work properly, and it turned out that this is related with the
codec auto-suspend. Namely, after the probe phase, the usage count
goes zero, and the auto-suspend is programmed, but the codec is kept
still active until the auto-suspend expiration. When an application
(e.g. alsactl) updates the mixer values at this moment, the values are
cached but not actually written. Then, starting arecord thereafter
also results in the silence because of the missing unmute.
The root cause is the handling of "lazy update" mode; when a mixer
value is updated *after* the suspend, it should update only the cache
and exits. At the resume, the cached value is written to the device,
in turn. The problem is that the current code misinterprets the state
of auto-suspend as if it were already suspended.
Although we can add the check of the actual device state after
pm_runtime_get_if_in_use() for catching the missing state, this won't
suffice; the second call of regmap_update_bits_check() will skip
writing the register because the cache has been already updated by the
first call. So we'd need fixes in two different places.
OTOH, a simpler fix is to replace pm_runtime_get_if_in_use() with
pm_runtime_get_if_active() (with ign_usage_count=true). This change
implies that the driver takes the pm refcount if the device is still
in ACTIVE state and continues the processing. A small caveat is that
this will leave the auto-suspend timer. But, since the timer callback
itself checks the device state and aborts gracefully when it's active,
this won't be any substantial problem.
Long story short: we address the missing register-write problem just
by replacing the pm_runtime_*() call in snd_hda_keep_power_up().
Fixes: fc4f000bf8 ("ALSA: hda - Fix unexpected resume through regmap code path")
Reported-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Closes: https://lore.kernel.org/r/a7478636-af11-92ab-731c-9b13c582a70d@linux.intel.com
Suggested-by: Cezary Rojewski <cezary.rojewski@intel.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20230518113520.15213-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2efbafb91e upstream.
Consider the following sequence of events:
1) A page in a PROT_READ|PROT_WRITE VMA is faulted.
2) Page migration allocates a page with the KASAN allocator,
causing it to receive a non-match-all tag, and uses it
to replace the page faulted in 1.
3) The program uses mprotect() to enable PROT_MTE on the page faulted in 1.
As a result of step 3, we are left with a non-match-all tag for a page
with tags accessible to userspace, which can lead to the same kind of
tag check faults that commit e74a684680 ("arm64: Reset KASAN tag in
copy_highpage with HW tags only") intended to fix.
The general invariant that we have for pages in a VMA with VM_MTE_ALLOWED
is that they cannot have a non-match-all tag. As a result of step 2, the
invariant is broken. This means that the fix in the referenced commit
was incomplete and we also need to reset the tag for pages without
PG_mte_tagged.
Fixes: e5b8d92189 ("arm64: mte: reset the page tag in page->flags")
Cc: <stable@vger.kernel.org> # 5.15
Link: https://linux-review.googlesource.com/id/I7409cdd41acbcb215c2a7417c1e50d37b875beff
Signed-off-by: Peter Collingbourne <pcc@google.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Link: https://lore.kernel.org/r/20230420210945.2313627-1-pcc@google.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit de3004c874 upstream.
In preparation for removing security_old_inode_init_security(), switch to
security_inode_init_security().
Extend the existing ocfs2_initxattrs() to take the
ocfs2_security_xattr_info structure from fs_info, and populate the
name/value/len triple with the first xattr provided by LSMs.
As fs_info was not used before, ocfs2_initxattrs() can now handle the case
of replicating the behavior of security_old_inode_init_security(), i.e.
just obtaining the xattr, in addition to setting all xattrs provided by
LSMs.
Supporting multiple xattrs is not currently supported where
security_old_inode_init_security() was called (mknod, symlink), as it
requires non-trivial changes that can be done at a later time. Like for
reiserfs, even if EVM is invoked, it will not provide an xattr (if it is
not the first to set it, its xattr will be discarded; if it is the first,
it does not have xattrs to calculate the HMAC on).
Finally, since security_inode_init_security(), unlike
security_old_inode_init_security(), returns zero instead of -EOPNOTSUPP if
no xattrs were provided by LSMs or if inodes are private, additionally
check in ocfs2_init_security_get() if the xattr name is set.
If not, act as if security_old_inode_init_security() returned -EOPNOTSUPP,
and set si->enable to zero to notify to the functions following
ocfs2_init_security_get() that no xattrs are available.
Signed-off-by: Roberto Sassu <roberto.sassu@huawei.com>
Reviewed-by: Casey Schaufler <casey@schaufler-ca.com>
Acked-by: Joseph Qi <joseph.qi@linux.alibaba.com>
Reviewed-by: Mimi Zohar <zohar@linux.ibm.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from upstream fc96ec826b)
On CPM, the RISC core is a lot more efficiant when doing transfers
in 16-bits chunks than in 8-bits chunks, but unfortunately the
words need to be byte swapped as seen in a previous commit.
So, for large tranfers with an even size, allocate a temporary tx
buffer and byte-swap data before and after transfer.
This change allows setting higher speed for transfer. For instance
on an MPC 8xx (CPM1 comms RISC processor), the documentation tells
that transfer in byte mode at 1 kbit/s uses 0.200% of CPM load
at 25 MHz while a word transfer at the same speed uses 0.032%
of CPM load. This means the speed can be 6 times higher in
word mode for the same CPM load.
For the time being, only do it on CPM1 as there must be a
trade-off between the CPM load reduction and the CPU load required
to byte swap the data.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/f2e981f20f92dd28983c3949702a09248c23845c.1680371809.git.christophe.leroy@csgroup.eu
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(backported from upstream 8a5299a127)
For different reasons, fsl-spi driver performs bits_per_word
modifications for different reasons:
- On CPU mode, to minimise amount of interrupts
- On CPM/QE mode to work around controller byte order
For CPU mode that's done in fsl_spi_prepare_message() while
for CPM mode that's done in fsl_spi_setup_transfer().
Reunify all of it in fsl_spi_prepare_message(), and catch
impossible cases early through master's bits_per_word_mask
instead of returning EINVAL later.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/0ce96fe96e8b07cba0613e4097cfd94d09b8919a.1680371809.git.christophe.leroy@csgroup.eu
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4eda19cc8a upstream.
The watchdog countdown is supposed to begin when the device file is
opened. Instead, it would begin countdown upon the first write to or
close of the device file. Now, the ping operation is called within the
start operation which ensures the countdown begins. From experimenation,
it does not appear possible to do this with a single write including
both the start bit and the trigger bit. So, it is done as two distinct
writes.
Signed-off-by: Gregory Oakes <gregory.oakes@amd.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20230316201312.17538-1-gregory.oakes@amd.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Cc: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a784452872 ]
Current only one entry is enabled but IP itself is using 4 different IDs
which are already listed in zynqmp.dtsi.
sata: ahci@fd0c0000 {
compatible = "ceva,ahci-1v84";
...
iommus = <&smmu 0x4c0>, <&smmu 0x4c1>,
<&smmu 0x4c2>, <&smmu 0x4c3>;
};
Fixes: 8ac47837f0 ("arm64: dts: zynqmp: Add missing iommu IDs")
Cc: stable@vger.kernel.org # v5.12+
Signed-off-by: Michal Simek <michal.simek@amd.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4e8ef34e36 ]
When work in gadget mode, currently driver doesn't update software level
link_state correctly as link state change event is not enabled for most
devices, in function dwc3_gadget_suspend_interrupt(), it will only pass
suspend event to UDC core when software level link state changes, so when
interrupt generated in sequences of suspend -> reset -> conndone ->
suspend, link state is not updated during reset and conndone, so second
suspend interrupt event will not pass to UDC core.
Remove link_state compare in dwc3_gadget_suspend_interrupt() and add a
suspended flag to replace the compare function.
Fixes: 799e9dc829 ("usb: dwc3: gadget: conditionally disable Link State change events")
Cc: stable <stable@kernel.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Linyu Yuan <quic_linyyuan@quicinc.com>
Link: https://lore.kernel.org/r/20230512004524.31950-1-quic_linyyuan@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b93c2a68f3 ]
The wakeup bit in the bmAttributes field indicates whether the device
is configured for remote wakeup. But this field should be allowed to
set only if the UDC supports such wakeup mechanism. So configure this
field based on UDC capability. Also inform the UDC whether the device
is configured for remote wakeup by implementing a gadget op.
Reviewed-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Elson Roy Serrao <quic_eserrao@quicinc.com>
Link: https://lore.kernel.org/r/1679694482-16430-2-git-send-email-quic_eserrao@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 4e8ef34e36 ("usb: dwc3: fix gadget mode suspend interrupt handler issue")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit bfdc750c4c upstream.
We forgot to add the 3D pen ID a year ago. There are two new pro pen
IDs to be added.
Signed-off-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0627f3df95 upstream.
Add the new PIDs to wacom_wac.c to support the new model in the Intuos Pro series.
Signed-off-by: Ping Cheng <ping.cheng@wacom.com>
Tested-by: Aaron Armstrong Skomra <aaron.skomra@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Cc: Ping Cheng <pinglinux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 94b179052f upstream.
Prox-out events may not be reliably sent by some AES firmware. This can
cause problems for users, particularly due to arbitration logic disabling
touch input while the pen is in prox.
This commit adds a timer which is reset every time a new prox event is
received. When the timer expires we check to see if the pen is still in
prox and force it out if necessary. This is patterend off of the same
solution used by 'hid-letsketch' driver which has a similar problem.
Link: https://github.com/linuxwacom/input-wacom/issues/310
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Cc: Ping Cheng <pinglinux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2862a2fdfa upstream.
Use "a" constraint instead of "d" constraint to pass the state parameter to
the do_sqbs() inline assembly. This prevents that general purpose register
zero is used for the state parameter.
If the compiler would select general purpose register zero this would be
problematic for the used instruction in rsy format: the register used for
the state parameter is a base register. If the base register is general
purpose register zero the contents of the register are unexpectedly ignored
when the instruction is executed.
This only applies to z/VM guests using QIOASSIST with dedicated (pass through)
QDIO-based devices such as FCP [zfcp driver] as well as real OSA or
HiperSockets [qeth driver].
A possible symptom for this case using zfcp is the following repeating kernel
message pattern:
zfcp <devbusid>: A QDIO problem occurred
zfcp <devbusid>: A QDIO problem occurred
zfcp <devbusid>: qdio: ZFCP on SC <sc> using AI:1 QEBSM:1 PRI:1 TDD:1 SIGA: W
zfcp <devbusid>: A QDIO problem occurred
zfcp <devbusid>: A QDIO problem occurred
Each of the qdio problem message can be accompanied by the following entries
for the affected subchannel <sc> in
/sys/kernel/debug/s390dbf/qdio_error/hex_ascii for zfcp or qeth:
<sc> ccq: 69....
<sc> SQBS ERROR.
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Cc: Steffen Maier <maier@linux.ibm.com>
Fixes: 8129ee1642 ("[PATCH] s390: qdio V=V pass-through")
Cc: <stable@vger.kernel.org>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9b5a04ac3a upstream.
During unmount process of nilfs2, nothing holds nilfs_root structure after
nilfs2 detaches its writer in nilfs_detach_log_writer(). However, since
nilfs_evict_inode() uses nilfs_root for some cleanup operations, it may
cause use-after-free read if inodes are left in "garbage_list" and
released by nilfs_dispose_list() at the end of nilfs_detach_log_writer().
Fix this issue by modifying nilfs_evict_inode() to only clear inode
without additional metadata changes that use nilfs_root if the file system
is degraded to read-only or the writer is detached.
Link: https://lkml.kernel.org/r/20230509152956.8313-1-konishi.ryusuke@gmail.com
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@gmail.com>
Reported-by: syzbot+78d4495558999f55d1da@syzkaller.appspotmail.com
Closes: https://lkml.kernel.org/r/00000000000099e5ac05fb1c3b85@google.com
Tested-by: Ryusuke Konishi <konishi.ryusuke@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 66b2ca0862 upstream.
It was reported that soft dirty tracking doesn't work when using the
Radix MMU.
The tracking is supposed to work by clearing the soft dirty bit for a
mapping and then write protecting the PTE. If/when the page is written
to, a page fault occurs and the soft dirty bit is added back via
pte_mkdirty(). For example in wp_page_reuse():
entry = maybe_mkwrite(pte_mkdirty(entry), vma);
if (ptep_set_access_flags(vma, vmf->address, vmf->pte, entry, 1))
update_mmu_cache(vma, vmf->address, vmf->pte);
Unfortunately on radix _PAGE_SOFTDIRTY is being dropped by
radix__ptep_set_access_flags(), called from ptep_set_access_flags(),
meaning the soft dirty bit is not set even though the page has been
written to.
Fix it by adding _PAGE_SOFTDIRTY to the set of bits that are able to be
changed in radix__ptep_set_access_flags().
Fixes: b0b5e9b130 ("powerpc/mm/radix: Add radix pte #defines")
Cc: stable@vger.kernel.org # v4.7+
Reported-by: Dan Horák <dan@danny.cz>
Link: https://lore.kernel.org/r/20230511095558.56663a50f86bdc4cd97700b7@danny.cz
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230511114224.977423-1-mpe@ellerman.id.au
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e7d3e5c4b1 upstream.
The P360 Tiny suffers from an irq storm issue like the T490s, so add
an entry for it to tpm_tis_dmi_table, and force polling. There also
previously was a report from the previous attempt to enable interrupts
that involved a ThinkPad L490. So an entry is added for it as well.
Cc: stable@vger.kernel.org
Reported-by: Peter Zijlstra <peterz@infradead.org> # P360 Tiny
Closes: https://lore.kernel.org/linux-integrity/20230505130731.GO83892@hirez.programming.kicks-ass.net/
Signed-off-by: Jerry Snitselaar <jsnitsel@redhat.com>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1f7aacc5eb upstream.
For an SR-IOV device, while enabling DDW, a new table is created and
added at index 1 in the group. In the below 2 scenarios, the table is
incorrectly referenced at index 0 (which is where the table is for
default DMA window).
1. When adding DDW
This issue is exposed with "slub_debug". Error thrown out from
dma_iommu_dma_supported()
Warning: IOMMU offset too big for device mask
mask: 0xffffffff, table offset: 0x800000000000000
2. During Dynamic removal of the PCI device.
Error is from iommu_tce_table_put() since a NULL table pointer is
passed in.
Fixes: 381ceda88c ("powerpc/pseries/iommu: Make use of DDW for indirect mapping")
Cc: stable@vger.kernel.org # v5.15+
Signed-off-by: Gaurav Batra <gbatra@linux.vnet.ibm.com>
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230505184701.91613-1-gbatra@linux.vnet.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
