When I use the axp20x chip to power my SDIO device on the 5.4 kernel,
the output voltage of DLDO2 is wrong. After comparing the register
manual and source code of the chip, I found that the mask bit of the
driver register of the port was wrong. I fixed this error by modifying
the mask register of the source code. This error seems to be a copy
error of the macro when writing the code. Now the voltage output of
the DLDO2 port of axp20x is correct. My development environment is
Allwinner A40I of arm architecture, and the kernel version is 5.4.
Signed-off-by: DingHua Ma <dinghua.ma.sz@gmail.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Cc: <stable@vger.kernel.org>
Fixes: db4a555f7c ("regulator: axp20x: use defines for masks")
Link: https://lore.kernel.org/r/20201201001000.22302-1-dinghua.ma.sz@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
A single fix for incorrect specification of some of the register fields
on axp20x devices which would break voltage setting on affected systems.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl9uTFQTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0OEZB/9tRSg6gHVdp2OwAbWPzJQcHYYP4stQ
H3mPcsDJRmpVnHhUQe3qlUvG4QZ7bDhnHFYS1G7LFgEBNVhCwKtpnseaQMJaCaa+
t9LLWNtzltuo75995bBtPYcSQI6U0yUYbu7U7n+4vibh/pjqY3eNg4lLrWtVL/OC
FwkCEql5+ZTTg3OcRHzKlYe1UlOB0kSHNCjySiVytPrC0UH32gFCs/LSZxDR8lbo
a9x8Vi8brbcmpASoCY0d+c0hM6PWB/chNwVHGnoWYJ+xoJMVLzC8TN/mkUgG++9i
wnwXfbUd0EbLKuLrZto0qdx14n2nLp2YpeLJhTbsJaQ5C+FQGvv7D2v5
=Uvnh
-----END PGP SIGNATURE-----
Merge tag 'regulator-fix-v5.9-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fix from Mark Brown:
"A single fix for incorrect specification of some of the register
fields on axp20x devices which would break voltage setting on affected
systems"
* tag 'regulator-fix-v5.9-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: axp20x: fix LDO2/4 description
Currently we wrongly set the mask of value of LDO2/4 both to the mask of
LDO2, and the LDO4 voltage configuration is left untouched. This leads
to conflict when LDO2/4 are both in use.
Fix this issue by setting different vsel_mask to both regulators.
Fixes: db4a555f7c ("regulator: axp20x: use defines for masks")
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Link: https://lore.kernel.org/r/20200923005142.147135-1-icenowy@aosc.io
Signed-off-by: Mark Brown <broonie@kernel.org>
Change the regulator helpers to use common linear_ranges code.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Link: https://lore.kernel.org/r/64f01d5e381b8631a271616b7790f9d5640974fb.1588944082.git.matti.vaittinen@fi.rohmeurope.com
Signed-off-by: Mark Brown <broonie@kernel.org>
It works incidentally, because AXP20X_DCDC2_LDO3_V_RAMP_DCDC2_EN
is non-zero, but the false branch value really should be just 0.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20200222235634.243805-1-megous@megous.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Current code set incorrect bits when set ramp_delay for AXP20X_DCDC2,
fix it.
Fixes: d29f54df8b ("regulator: axp20x: add support for set_ramp_delay for AXP209")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Link: https://lore.kernel.org/r/20191221081049.32490-1-axel.lin@ingics.com
Signed-off-by: Mark Brown <broonie@kernel.org>
A copy-paste error was introduced when bitmasks were converted to
macros, incorrectly setting the enable bitmask for ELDO2 to the one
for ELDO1 for the AXP22x units.
Fix it by using the correct macro.
On affected boards, ELDO1 and/or ELDO2 are used to power the camera,
which is currently unsupported.
Fixes: db4a555f7c ("regulator: axp20x: use defines for masks")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20191218044720.21990-1-wens@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Refactoring of axp20x driver introduced a bug in AXP803's DCDC6
regulator definition. AXP803_DCDC6_1120mV_STEPS was obtained by
subtracting 0x47 and 0x33. This should be 0x14 (hex) and not 14
(dec).
Refactoring also carried over a bug in DCDC5 regulator definition.
Number of possible voltages must be for 1 bigger than maximum valid
voltage index, because 0 is also valid and it means lowest voltage.
Fixes: 1dbe0ccb06 ("regulator: axp20x-regulator: add support for AXP803")
Fixes: db4a555f7c ("regulator: axp20x: use defines for masks")
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://lore.kernel.org/r/20190713090717.347-3-jernej.skrabec@siol.net
Signed-off-by: Mark Brown <broonie@kernel.org>
Refactoring of the driver introduced bugs in AXP806's DCDCA and DCDCD
regulator definitions.
In DCDCA case, AXP806_DCDCA_1120mV_STEPS was obtained by subtracting
0x47 and 0x33. This should be 0x14 (hex) and not 14 (dec).
In DCDCD case, axp806_dcdcd_ranges[] contains two ranges with same
start and end macros, which is clearly wrong. Second range starts at
1.6V so it should use AXP806_DCDCD_1600mV_[START|END] macros. They are
already defined but unused.
Fixes: db4a555f7c ("regulator: axp20x: use defines for masks")
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://lore.kernel.org/r/20190713090717.347-2-jernej.skrabec@siol.net
Signed-off-by: Mark Brown <broonie@kernel.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
This patch fixes the following warnings:
drivers/regulator/axp20x-regulator.c: In function ‘axp20x_set_dcdc_freq’:
drivers/regulator/axp20x-regulator.c:1023:7: warning: this statement may fall through [-Wimplicit-fallthrough=]
reg = AXP803_DCDC_FREQ_CTRL;
drivers/regulator/axp20x-regulator.c:1025:2: note: here
case AXP806_ID:
^~~~
drivers/regulator/axp20x-regulator.c: In function ‘axp20x_set_dcdc_workmode’:
drivers/regulator/axp20x-regulator.c:1115:7: warning: this statement may fall through [-Wimplicit-fallthrough=]
reg = AXP806_DCDC_MODE_CTRL2;
drivers/regulator/axp20x-regulator.c:1121:2: note: here
case AXP221_ID:
^~~~
Notice that in this particular case, I moved the whole comment
"Fall through to the check below.", which contains the "Fall through"
comment, at the bottom of the case, which is what GCC is expecting
to find.
Warning level 3 was used: -Wimplicit-fallthrough=3
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use rdev_get_id() to simplify the code a bit.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
rdev won't be NULL in .enable callback.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently rdev is dereferenced when assigning desc before rdev is null
checked, this is leading to static analysis warnings. However, rdev
can never be null, so the null check is redundant and can be removed.
Detected by CoverityScan, CID#1476031 ("Dereference before null check")
Fixes: 77e3e3b165 ("regulator: axp20x: add software based soft_start for AXP209 LDO3")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This fixes another set of errors from the refactoring of literals
to mask preproccesor definitions.
Found by debugging a broken voltage setup on Orange Pi One Plus.
Fixes: db4a555f7c ("regulator: axp20x: use defines for masks")
Signed-off-by: Ondrej Jirman <megous@megous.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Looks like refactoring didn't go well and left ALDO2, DLDO2 and ELDO3
definitions broken for AXP803 - now they are using register address
instead of mask. Fix it by using mask where necessary.
Fixes: db4a555f7c ("regulator: axp20x: use defines for masks")
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix copy-paste mistake while converting to use defines for masks.
Fixes: db4a555f7c ("regulator: axp20x: use defines for masks")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Looks like refactoring didn't go well and left ALDO2, DLDO2 and ELDO3
definitions broken for AXP803 - now they are using register address
instead of mask. Fix it by using mask where necessary.
Fixes: db4a555f7c ("regulator: axp20x: use defines for masks")
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently rdev is dereferenced when assigning desc before rdev is null
checked, hence there is a potential null pointer dereference on rdev.
Fix this by null checking rdev first.
Detected by CoverityScan, CID#1476031 ("Dereference before null check")
Fixes: 77e3e3b165 ("regulator: axp20x: add software based soft_start for AXP209 LDO3")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Initial commit of set_ramp_delay feature was missing an assignment which
should have populated slew_rate table for dcdc2 regulator. Add it.
Fixes: d29f54df8b ("regulator: axp20x: add support for set_ramp_delay for AXP209")
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
In the past, there have been words on various lists that if LDO3 is
disabled in u-boot, but enabled in the DTS, the axp209 driver would
fail to continue/hang. Several enable/disable patches have been
issues to devicetree's in both the kernel and u-boot to address
this issue.
What really happened however, was that the AXP209 shuts down without
a notice and without setting an interrupt. This is caused when LDO3
gets overloaded, for example with large capacitors on the LDO3 output.
Normally, we would expect that AXP209 would source 200 mA as per
datasheet and set and trigger an interrupt when being overloaded.
For some reason however, this does not happen.
As a work-around, we use the soft-start constraint of the regulator
node to first bring up the LDO3 to the lowest possible voltage and
then enable the LDO. After that, we can set the requested voltage
as usual.
Combining this setting with the regulator-ramp-delay allows LDO3 to
enable voltage slowly and staggered, potentially reducing overall
inrush current.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The AXP209 supports ramping up voltages on several regulators such as
DCDC2 and LDO3.
This patch adds preliminary support for the regulator-ramp-delay property
for these 2 regulators. Note that the voltage ramp only works when
regulator is already enabled. E.g. when going from say 0.7 V to 3.6 V.
When turning on the regulator, no voltage ramp is performed in hardware.
What this means, is that if the bootloader brings up the voltage at 0.7 V,
the ramp delay property is properly applied. If however, the bootloader
leaves the power off, no ramp delay is applied when the power is
enabled by the regulator framework.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The AXP20X driver currently has several masks defined throughout the
code. Use nice defines to make them clean and more descriptive.
Additionally include bitops.h, which was missing before, and sort
headers.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Notice that in this particular case, I moved the whole comment
"Fall through to the check below.", which contains the "Fall through"
comment, at the bottom of the case, which is what GCC is expecting
to find.
Addresses-Coverity-ID: 1436594 ("Missing break in switch")
Addresses-Coverity-ID: 1364475 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Like axp221, axp223, axp813 the axp803 is also supporting external
regulator to drive the OTG VBus through N_VBUSEN PMIC pin.
Add support for it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The code to handle AXP803_ID and AXP813_ID cases are exactly the same.
Make the switch-case fall through to avoid duplicate code.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The AXP813 PMIC has 7 DC-DC buck regulators, 16 LDOs (including the
fixed RTC LDO and 2 GPIO LDOs), and 1 switchable. The drive-vbus
feature is also supported. All the hardware details are very similar
to the AXP803, with the following exceptions:
- Extra DCDC7 buck regulator, with the same range as DCDC6
- SWitch now has a separate supply pin, instead of being chained
internaly from DCDC1
- RTC LDO output voltage is now 1.8V
- FLDO3 is an LDO with switchable supplies, but unconfigurable output
voltage. The voltage is always half that of its supply.
Support for FLDO3 is currently unimplemented, as it requires runtime
switching of its supplies, something the regulator subsystem does not
support. It is not used in either the reference designs nor actually
produced boards available.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The bit offset used to check if DCDC5 and DCDC6 are tied together in
poly-phase output is wrong. It was checking against a reserved bit,
which is always false.
In reality, neither the reference design layout nor actually produced
boards tie these two buck regulators together. But we should still
fix it, just in case.
Fixes: 1dbe0ccb06 ("regulator: axp20x-regulator: add support for AXP803")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Check return value from call to devm_kzalloc()
in order to prevent a NULL pointer dereference.
This issue was detected using Coccinelle and the following semantic patch:
@@
expression x;
identifier fld;
@@
* x = devm_kzalloc(...);
... when != x == NULL
x->fld
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
AXP803 PMIC also have a series of regulators (DCDCs and LDOs)
controllable via I2C/RSB bus.
Add support for them.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Declare regulator_ops structure as const as it is only stored in the ops
field of a regulator_desc structure. This field is of type const, so
regulator_ops structures having this property can be made const too.
File size before: drivers/regulator/axp20x-regulator.o
text data bss dec hex filename
16848 1232 0 18080 46a0 regulator/axp20x-regulator.o
File size after: drivers/regulator/axp20x-regulator.o
text data bss dec hex filename
17888 192 0 18080 46a0 regulator/axp20x-regulator.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
A typo or copy-paste bug means that the register access intended for
regulator dcdce goes to dcdcb instead. This patch corrects it.
Fixes: 2ca342d391 (regulator: axp20x: Support AXP806 variant)
Signed-off-by: Rask Ingemann Lambertsen <rask@formelder.dk>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The maximum supported voltage for ldo_io# is 3.3V, but on cold boot
the selector comes up at 0x1f, which maps to 3.8V. This was previously
corrected by Allwinner's U-boot, which set all regulators on the PMICs
to some pre-configured voltage. With recent progress in U-boot SPL
support, this is no longer the case. In any case we should handle
this quirk in the kernel driver as well.
This invalid setting causes _regulator_get_voltage() to fail with -EINVAL
which causes regulator registration to fail when constrains are used:
[ 1.054181] vcc-pg: failed to get the current voltage(-22)
[ 1.059670] axp20x-regulator axp20x-regulator.0: Failed to register ldo_io0
[ 1.069749] axp20x-regulator: probe of axp20x-regulator.0 failed with error -22
This commits makes the axp20x regulator driver accept the 0x1f register
value, fixing this.
The datasheet does not guarantee reliable operation above 3.3V, so on
boards where this regulator is used the regulator-max-microvolt setting
must be 3.3V or less.
This is essentially the same as the commit f40d4896bf ("regulator:
axp20x: Fix axp22x ldo_io registration error on cold boot") for AXP22x
PMICs.
Fixes: a51f9f4622 ("regulator: axp20x: support AXP809 variant")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The X-Powers AXP806 PMIC has a new set of buck and LDO regulators, and
also a switch. The buck regulators support teaming into multi-phase
groups, with A+B, A+B+C, D+E groupings.
Some registers controlling DCDC converter work settings are at different
offsets. Deal with them as well.
Add support for this new variant.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The axp20x pmics have 2 power inputs, one called ACIN which is intended
for to be supplied via a powerbarrel on the board and one called VBUS
which is intended to be supplied via an otg connector.
In the VBUS case the pmic needs to know if the board is supplying power
to the otg connector, because then it should not take any power from
its VBUS pin. The axp209 pmic has a N_VBUSEN input pin via which the
board can signal to the pmic whether the board is supplying power to the
otg connector or not.
On the axp221/axp223 this pin can alternatively be used as an output
which controls an external regulator which (optionally) supplies
power to the otg connector from the board. When the pin is used as
output it is called DRIVEVBUS in the datasheet.
This commit adds support for the DRIVEVBUS pin as an extra pmic
controlled regulator. Since this is optional a new x-powers,drivebus dt
property is added. When this is present the misc-control register is
written to change the N_VBUSEN input pin to DRIVEVBUS output pin mode and
the extra drivebus regulator is registered with the regulator subsystem.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The X-Powers AXP809 PMIC has a similar set of regulators as the AXP221,
though a few LDOs were removed, and a new switch output added. Like the
AXP221, AXP809 also has DC1SW and DC5LDO, which are internally chained
to DCDC1 and DCDC5, respectively.
Add support for this new variant. Also remove the "axp22x_" prefix from
DC1SW/DC5LDO supply handling code, as the AXP809 uses it as well.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The maximum supported voltage for ldo_io# is 3.3V, but on cold
boot the selector comes up at 0x1f, which maps to 3.8V.
This causes _regulator_get_voltage() to fail with -EINVAL which
causes regulator registration to fail when constrains are used:
[ 1.467788] vcc-touchscreen: failed to get the current voltage(-22)
[ 1.474209] axp20x-regulator axp20x-regulator: Failed to register ldo_io1
[ 1.483363] axp20x-regulator: probe of axp20x-regulator failed with error -22
This commits makes the axp20x regulator driver accept the 0x1f register
value, fixing this.
The datasheet does not guarantee reliable operation above 3.3V, so on
boards where this regulator is used the regulator-max-microvolt setting
must be 3.3V or less.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The minium voltage of 1800mV is a copy and paste error from the axp20x
regulator info. The correct minimum voltage for the ldo_io regulators
on the axp22x is 700mV.
Fixes: 1b82b4e4f9 ("regulator: axp20x: Add support for AXP22X regulators")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The current linear voltage range for the LDO4 regulator found in the APX20X
PMICs assumes that the voltage is linear between 2.5 and 3.1V.
However, the PMIC can output up to 3.3V on that regulator by skipping the
2.6V and 2.9V steps.
Fix the ranges to read and set the proper voltages.
Fixes: 13d57e6435 ("regulator: axp20x: Use linear voltage ranges for AXP20X LDO4")
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
- Freescale Touch Screen ADC
- X-Powers AXP PMIC with RSB
- TI TPS65086 Power Management IC (PMIC)
- New Device Support
- Supply device PCI IDs for Intel Broxton
- Fix-ups
- Move to clkdev_create() API; intel_quark_i2c_gpio
- Complete re-write of TI's TPS65912 Power Management IC (PMIC)
- Remove unnecessary function argument; axp20x
- Separate out bus related code; axp20x
- Coding Style changes; axp20x
- Allow more drivers to be compiled as modules
- Work around false positive 'used uninitialised' warning; db8500-prcmu
- Bug Fixes
- Remove do_div(); fsl-imx25-gcq
- Fix driver init when built-in; tps65010
- Fix clock-unregister leak; intel-lpss
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=gTBA
-----END PGP SIGNATURE-----
Merge tag 'mfd-for-linus-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Drivers:
- Freescale Touch Screen ADC
- X-Powers AXP PMIC with RSB
- TI TPS65086 Power Management IC (PMIC)
New Device Support:
- Supply device PCI IDs for Intel Broxton
Fix-ups:
- Move to clkdev_create() API; intel_quark_i2c_gpio
- Complete re-write of TI's TPS65912 Power Management IC (PMIC)
- Remove unnecessary function argument; axp20x
- Separate out bus related code; axp20x
- Coding Style changes; axp20x
- Allow more drivers to be compiled as modules
- Work around false positive 'used uninitialised' warning; db8500-prcmu
Bug Fixes:
- Remove do_div(); fsl-imx25-gcq
- Fix driver init when built-in; tps65010
- Fix clock-unregister leak; intel-lpss"
* tag 'mfd-for-linus-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (53 commits)
mfd: intel-lpss: Pass I2C configuration via properties on BXT
mfd: imx6sx: Add PCIe register definitions for iomuxc gpr
mfd: ipaq-micro: Use __maybe_unused to hide pm functions
mfd: max77686: Add max77802 to I2C device ID table
mfd: max77686: Export OF module alias information
mfd: max77686: Allow driver to be built as a module
mfd: stmpe: Add the proper PWM resources
mfd: tps65090: Set regmap config reg counts properly
mfd: syscon: Return ENOTSUPP instead of ENOSYS when disabled
mfd: as3711: Set regmap config reg counts properly
mfd: rc5t583: Set regmap config reg counts properly
gpio: tps65086: Add GPO driver for the TPS65086 PMIC
mfd: mt6397: Add platform device ID table
mfd: da9063: Fix missing volatile registers in the core regmap_range volatile lists
mfd: mt6397: Add MT6323 support to MT6397 driver
mfd: mt6397: Add support for different Slave types
mfd: mt6397: int_con and int_status may vary in location
dt-bindings: mfd: Add bindings for the MediaTek MT6323 PMIC
mfd: da9062: Fix missing volatile registers in the core regmap_range volatile lists
mfd: Add documentation for ACT8945A DT bindings
...
Originally the helper macros used uppercase regulator names, which
are primarily used to expand to the regulator ID enum, as the default
names. This is aestheticly unpleasent.
Since the of_match bits are the same, just lowercase, use that as the
default names instead.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The AXP223 is a new PMIC commonly paired with Allwinner A23/A33 SoCs.
It is functionally identical to AXP221; only the regulator default
voltage/status and the external host interface are different.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
AXP20X datasheet lists the possible voltage settings for LDO4, so
it was implemented using a voltage table. Upon closer examination,
the valid voltages can be mapped into 3 linear ranges.
Move AXP20X LDO4 to use linear ranges. The supporting code can be
reused with later AXP8xx PMICs, which have a number of regulators
that have 2 linear ranges.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Switch-type regulators, such as DC1SW on AXP22X, are a secondary output
from DCDC1. They are just an on/off switch, and the driver should not
try to read its voltage directly from the DCDC1 control registers.
Instead, the core will pass down the voltage from the regulator supply
chain.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The enable/disable values for GPIO LDOs are reversed. It seems no one
noticed as AXP22x support was introduced recently, and no one was using
the GPIO LDOs, either because no designs actually use them or board
support hasn't caught up.
Fixes: 1b82b4e4f9 ("regulator: axp20x: Add support for AXP22X regulators")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The DC1SW and DC5LDO regulators in the AXP22X are internally chained
to DCDC1 and DCDC5, hence the names. The original bindings used the
parent regulator names for the supply regulator property.
Since they are internally connected, the relationship should not be
represented in the device tree, but handled internally by the driver.
This patch has the driver remember the regulator names for the parent
DCDC1/DCDC5, and use them as supply names for DC1SW/DC5LDO.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
