The only slightly tricky merge conflict was the netdevsim because the
mutex locking fix overlapped a lot of driver reload reorganization.
The rest were (relatively) trivial in nature.
Signed-off-by: David S. Miller <davem@davemloft.net>
Third set of fixes for 5.4. Most of them are for iwlwifi but important
fixes also for rtlwifi and mt76, the overflow fix for rtlwifi being
most important.
iwlwifi
* fix merge damage on earlier patch
* various fixes to device id handling
* fix scan config command handling which caused firmware asserts
rtlwifi
* fix overflow on P2P IE handling
* don't deliver too small frames to mac80211
mt76
* disable PCIE_ASPM
* fix buffer DMA unmap on certain cases
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJdvEesAAoJEG4XJFUm622bbQQH+we6ATCGLxEFtRhlPALEeXqk
up/eJTL+fQoZ2Z0IxarZT05rhBK9VNAiDXE2fuPB0lUuL1//7FrrG337vWFmM41b
FJE2ESf0Q8fKeceRDbe+4QgzgCSg2uSB9IgCo2jwXjTVjlFLufT8oUBGlUQU160b
L3H/GuBYNlE1dmLyBXZCqR74DRvKTf3Uh8FfHxO41Mv64LjhotXJ+tIWboUJr5N5
uU9eAyW7MV7sL+XQyN5IYIZ595gyRjIwD5U5kuX/8vEcGusqfMUKv/IBH8LFlQYl
akY9n4ozpxSxUmcors4RBjb//XihjgtDldEGxG6EqkD+0DokM+nQiYteFzgBnrE=
=sbTa
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-2019-11-01' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 5.4
Third set of fixes for 5.4. Most of them are for iwlwifi but important
fixes also for rtlwifi and mt76, the overflow fix for rtlwifi being
most important.
iwlwifi
* fix merge damage on earlier patch
* various fixes to device id handling
* fix scan config command handling which caused firmware asserts
rtlwifi
* fix overflow on P2P IE handling
* don't deliver too small frames to mac80211
mt76
* disable PCIE_ASPM
* fix buffer DMA unmap on certain cases
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The API was reduced to include only knowledge currently needed by the
FW scan logic, the rest is legacy. Support the new, reduced version.
Using the old API with newer firmwares (starting from
iwlwifi-*-50.ucode, which implements and requires the new API version)
causes an assertion failure similar to this one:
[ 2.854505] iwlwifi 0000:00:14.3: 0x20000038 | BAD_COMMAND
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
mt76 dma layer is supposed to unmap skb data buffers while keep txwi
mapped on hw dma ring. At the moment mt76 wrongly unmap txwi or does
not unmap data fragments in even positions for non-linear skbs. This
issue may result in hw hangs with A-MSDU if the system relies on IOMMU
or SWIOTLB. Fix this behaviour properly unmapping data fragments on
non-linear skbs.
Fixes: 17f1de56df ("mt76: add common code shared between multiple chipsets")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
On same device (e.g. U7612E-H1) PCIE_ASPM causes continuous mcu hangs and
instability. Since mt76x2 series does not manage PCIE PS states, first we
try to disable ASPM using pci_disable_link_state. If it fails, we will
disable PCIE PS configuring PCI registers.
This patch has been successfully tested on U7612E-H1 mini-pice card
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fix misspellings of "disconnect", "disconnecting", "connections", and
"disconnected".
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Acked-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix various misspellings of "configuration" and "configure".
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some interface types could be nested.
(VLAN, BONDING, TEAM, MACSEC, MACVLAN, IPVLAN, VIRT_WIFI, VXLAN, etc..)
These interface types should set lockdep class because, without lockdep
class key, lockdep always warn about unexisting circular locking.
In the current code, these interfaces have their own lockdep class keys and
these manage itself. So that there are so many duplicate code around the
/driver/net and /net/.
This patch adds new generic lockdep keys and some helper functions for it.
This patch does below changes.
a) Add lockdep class keys in struct net_device
- qdisc_running, xmit, addr_list, qdisc_busylock
- these keys are used as dynamic lockdep key.
b) When net_device is being allocated, lockdep keys are registered.
- alloc_netdev_mqs()
c) When net_device is being free'd llockdep keys are unregistered.
- free_netdev()
d) Add generic lockdep key helper function
- netdev_register_lockdep_key()
- netdev_unregister_lockdep_key()
- netdev_update_lockdep_key()
e) Remove unnecessary generic lockdep macro and functions
f) Remove unnecessary lockdep code of each interfaces.
After this patch, each interface modules don't need to maintain
their lockdep keys.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 8020919a9b ("mac80211: Properly handle SKB with radiotap
only"), buffers whose length is too short cause a WARN_ON(1) to be
executed. This change exposed a fault in rtlwifi drivers, which is fixed
by regarding packets with skb->len <= FCS_LEN as though they are in error
and dropping them. The test is now annotated as likely.
Cc: Stable <stable@vger.kernel.org> # v5.0+
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When converting the wrong qu configurations in an earlier commit, I
accidentally swapped 0x2720 and 0x30DC. Instead of converting 0x2720,
I converted 0x30DC. Undo 0x30DC and convert 0x2720.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add a workaround that forces power gating to be enabled on integrated
22000 devices. This improves power saving in certain situations.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
iwl_mvm_tvqm_enable_txq() can return an error, notably if unable
to allocate memory for the queue. Handle this error throughout,
avoiding storing the invalid value into a u16 which later leads
to a disable of an invalid queue ("queue 65524 not used", where
65524 is just -ENOMEM in a u16).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
A bunch of the entries for qnj were wrong. The 9460 device doesn't
exist, so update them to 9461 and 9462. There are still a bunch of
other occurrences of 9460, but that will be fixed separately.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Some entries for PCI ID 0x2720 were using iwl9260_2ac_cfg, but the
correct is to use iwl9260_2ac_cfg_soc. Fix that.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Nicolas Waisman noticed that even though noa_len is checked for
a compatible length it's still possible to overrun the buffers
of p2pinfo since there's no check on the upper bound of noa_num.
Bound noa_num against P2P_MAX_NOA_NUM.
Reported-by: Nicolas Waisman <nico@semmle.com>
Signed-off-by: Laura Abbott <labbott@redhat.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Two patches were sent out of order: one removed some conditions from
an if and the other moved the code elsewhere. When sending the patch
that moved the code, an older version of the original code was moved,
causing the "make QnJ exclusive" code to be essentially undone.
Fix that by removing the inclusive conditions from the check again.
Fixes: 809805a820 ("iwlwifi: pcie: move some cfg mangling from trans_pcie_alloc to probe")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Second set of fixes for 5.4. ath10k regression and iwlwifi BAD_COMMAND
bug are the ones getting most reports at the moment.
ath10k
* fix throughput regression on QCA98XX
iwlwifi
* fix initialization of 3168 devices (the infamous BAD_COMMAND bug)
* other smaller fixes
rt2x00
* don't include input-polldev.h header
* fix hw reset to work during first 5 minutes of system run
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJdpbPAAAoJEG4XJFUm622bDo8H/RhoLZrKWCf5G8N+jRhq5XmV
15uZ2OiAOircZzSeYQ6z32XyPqOocQaR831lDrwYi/pXU4WatjKOiVqeCtqHD3ro
WVc+n8+9jhSDTFxzGJEPoF1a9qu4r672Vc+orlPl2LKT7DO7fcaNMauHVP/o9fcT
H8+OGQySmGYGYPMxHU1EKkbG8egirRqkfZZNd9wJ+u8FLDqlwZlmyjt5mbAiG2j3
CYT4fwBG1IsjJcNJB4rjzhtBy2o3jWdxhSvYSUpPYSPCVsFLTl5SGOrLQgx5+0Cl
garU1b851JRx/9lxljT6rqj2ZH3q/JdTrXsMpflncBZYmAhNSspOWJtN77bbAkE=
=0Fdg
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2019-10-15' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 5.4
Second set of fixes for 5.4. ath10k regression and iwlwifi BAD_COMMAND
bug are the ones getting most reports at the moment.
ath10k
* fix throughput regression on QCA98XX
iwlwifi
* fix initialization of 3168 devices (the infamous BAD_COMMAND bug)
* other smaller fixes
rt2x00
* don't include input-polldev.h header
* fix hw reset to work during first 5 minutes of system run
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
(kvalo: cherry picked from commit 1340cc631b in
wireless-drivers-next to wireless-drivers as this a frequently reported
regression)
Bad latency is found on QCA988x, the issue was introduced by
commit 4504f0e5b5 ("ath10k: sdio: workaround firmware UART
pin configuration bug"). If uart_pin_workaround is false, this
change will set uart pin even if uart_print is false.
Tested HW: QCA9880
Tested FW: 10.2.4-1.0-00037
Fixes: 4504f0e5b5 ("ath10k: sdio: workaround firmware UART pin configuration bug")
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* minstrel improvements from Felix
* a TX aggregation simplification
* some additional capabilities for hwsim
* minor cleanups & docs updates
-----BEGIN PGP SIGNATURE-----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=IJ7D
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-net-next-2019-10-11' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
A few more small things, nothing really stands out:
* minstrel improvements from Felix
* a TX aggregation simplification
* some additional capabilities for hwsim
* minor cleanups & docs updates
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
There were a bunch of devices with qu and jf that were loading the
configuration with pu and jf, which is wrong. Fix them all
accordingly. Additionally, remove 0x1010 and 0x1210 subsytem IDs from
the list, since they are obviously wrong, and 0x0044 and 0x0244, which
were duplicate.
Cc: stable@vger.kernel.org # 5.1+
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We currently support two NICs in FW version 29, namely 7265D and 3168.
Out of these, only 7265D supports GEO SAR, so adjust the function that
checks for it accordingly.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Fixes: f5a47fae6a ("iwlwifi: mvm: fix version check for GEO_TX_POWER_LIMIT support")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In iwl_pcie_ctxt_info_gen3_init there are cases that the allocated dma
memory is leaked in case of error.
DMA memories prph_scratch, prph_info, and ctxt_info_gen3 are allocated
and initialized to be later assigned to trans_pcie. But in any error case
before such assignment the allocated memories should be released.
First of such error cases happens when iwl_pcie_init_fw_sec fails.
Current implementation correctly releases prph_scratch. But in two
sunsequent error cases where dma_alloc_coherent may fail, such
releases are missing.
This commit adds release for prph_scratch when allocation for
prph_info fails, and adds releases for prph_scratch and prph_info when
allocation for ctxt_info_gen3 fails.
Fixes: 2ee8240262 ("iwlwifi: pcie: support context information for 22560 devices")
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In alloc_sgtable if alloc_page fails, the alocated table should be
released.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We don't handle failures in the rb_allocator workqueue allocation
correctly. To fix that, move the code earlier so the cleanup is
easier and we don't have to undo all the interrupt allocations in
this case.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We got a crash in iwl_trans_pcie_get_cmdlen(), while the TFD was
being accessed to sum up the lengths.
We want to access the TFD here, which is the information for the
hardware. We always only allocate 32 buffers for the cmd queue,
but on newer hardware (using TFH) we can also allocate only a
shorter hardware array, also only 32 TFDs. Prior to the TFH, we
had to allocate a bigger TFD array but would make those point to
a smaller set of buffers.
Additionally, now max_tfd_queue_size is up to 65536, so we can
access *way* out of bounds of a really only 32-entry array, so
it crashes.
Fix this by making the TFD index depend on which hardware we are
using right now.
While changing the calculation, also fix it to not use void ptr
arithmetic, but cast to u8 * before.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Consider the following flow:
1. Driver starts to sync the rx queues due to a delba.
mvm->queue_sync_cookie=1.
This rx-queues-sync is synchronous, so it doesn't increment the
cookie until all rx queues handle the notification from FW.
2. During this time, driver starts to sync rx queues due to nssn sync
required.
The cookie's value is still 1, but it doesn't matter since this
rx-queue-sync is non-synchronous so in the notification handler the
cookie is ignored.
What _does_ matter is that this flow increments the cookie to 2
immediately.
Remember though that the FW won't start servicing this command until
it's done with the previous one.
3. FW is still handling the first command, so it sends a notification
with internal_notif->sync=1, and internal_notif->cookie=0, which
triggers a WARN_ONCE.
The solution for this race is to only use the mvm->queue_sync_cookie in
case of a synchronous sync-rx-queues. This way in step 2 the cookie's
value won't change so we avoid the WARN.
The commit in the "fixes" field is the first commit to introduce
non-synchronous sending of this command to FW.
Fixes: 3c514bf831 ("iwlwifi: mvm: add a loose synchronization of the NSSN across Rx queues")
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The PHY is initialized during device initialization, but devices with
the tx_siso_diversity flag set need to send PHY_CONFIGURATION_CMD first,
otherwise the PHY would be reinitialized, causing a SYSASSERT.
To fix this, use a bit that tells the FW not to complete the PHY
initialization before a PHY_CONFIGURATION_CMD is received.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We can't check for the ACPI table revision validity in the same if
where we check if the package was read correctly, because we return
PTR_ERR(pkg) and if the table is not valid but the pointer is, we
would return a valid pointer as an error. Fix that by moving the
table checks to a separate if and return -EINVAL if it's not valid.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We copy cfg->trans to trans->trans_cfg at the very beginning, so don't
try to access it via cfg->trans anymore, because the cfg may be unset
in later cases.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The driver does not use input subsystem so we do not need this header,
and it is being removed, so stop pulling it in.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If dev_alloc_name fails, hwsim_mon's memory allocated in alloc_netdev
needs to be freed.
Change goto command in dev_alloc_name failure to out_free_mon in
order to perform free_netdev.
Signed-off-by: Michael Vassernis <michael.vassernis@tandemg.com>
Link: https://lore.kernel.org/r/20191003073049.3760-1-michael.vassernis@tandemg.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There really is no need to make drivers call the
ieee80211_start_tx_ba_cb_irqsafe() function and then
schedule the worker if all we want is to set a bit.
Add a new return value (that was previously considered
invalid) to indicate that the driver is immediately
ready for the session, and make drivers use it. The
only drivers that remain different are the Intel ones
as they need to negotiate more with the firmware.
Link: https://lore.kernel.org/r/1570007543-I152912660131cbab2e5d80b4218238c20f8a06e5@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Initialize last_reset variable to INITIAL_JIFFIES, otherwise it is not
possible to test H/W reset for first 5 minutes of system run.
Fixes: e403fa31ed ("rt2x00: add restart hw")
Reported-and-tested-by: Jonathan Liu <net147@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
commit 174e23810c
("sk_buff: drop all skb extensions on free and skb scrubbing") made napi
recycle always drop skb extensions. The additional skb_ext_del() that is
performed via nf_reset on napi skb recycle is not needed anymore.
Most nf_reset() calls in the stack are there so queued skb won't block
'rmmod nf_conntrack' indefinitely.
This removes the skb_ext_del from nf_reset, and renames it to a more
fitting nf_reset_ct().
In a few selected places, add a call to skb_ext_reset to make sure that
no active extensions remain.
I am submitting this for "net", because we're still early in the release
cycle. The patch applies to net-next too, but I think the rename causes
needless divergence between those trees.
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Pull networking fixes from David Miller:
1) Sanity check URB networking device parameters to avoid divide by
zero, from Oliver Neukum.
2) Disable global multicast filter in NCSI, otherwise LLDP and IPV6
don't work properly. Longer term this needs a better fix tho. From
Vijay Khemka.
3) Small fixes to selftests (use ping when ping6 is not present, etc.)
from David Ahern.
4) Bring back rt_uses_gateway member of struct rtable, it's semantics
were not well understood and trying to remove it broke things. From
David Ahern.
5) Move usbnet snaity checking, ignore endpoints with invalid
wMaxPacketSize. From Bjørn Mork.
6) Missing Kconfig deps for sja1105 driver, from Mao Wenan.
7) Various small fixes to the mlx5 DR steering code, from Alaa Hleihel,
Alex Vesker, and Yevgeny Kliteynik
8) Missing CAP_NET_RAW checks in various places, from Ori Nimron.
9) Fix crash when removing sch_cbs entry while offloading is enabled,
from Vinicius Costa Gomes.
10) Signedness bug fixes, generally in looking at the result given by
of_get_phy_mode() and friends. From Dan Crapenter.
11) Disable preemption around BPF_PROG_RUN() calls, from Eric Dumazet.
12) Don't create VRF ipv6 rules if ipv6 is disabled, from David Ahern.
13) Fix quantization code in tcp_bbr, from Kevin Yang.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (127 commits)
net: tap: clean up an indentation issue
nfp: abm: fix memory leak in nfp_abm_u32_knode_replace
tcp: better handle TCP_USER_TIMEOUT in SYN_SENT state
sk_buff: drop all skb extensions on free and skb scrubbing
tcp_bbr: fix quantization code to not raise cwnd if not probing bandwidth
mlxsw: spectrum_flower: Fail in case user specifies multiple mirror actions
Documentation: Clarify trap's description
mlxsw: spectrum: Clear VLAN filters during port initialization
net: ena: clean up indentation issue
NFC: st95hf: clean up indentation issue
net: phy: micrel: add Asym Pause workaround for KSZ9021
net: socionext: ave: Avoid using netdev_err() before calling register_netdev()
ptp: correctly disable flags on old ioctls
lib: dimlib: fix help text typos
net: dsa: microchip: Always set regmap stride to 1
nfp: flower: fix memory leak in nfp_flower_spawn_vnic_reprs
nfp: flower: prevent memory leak in nfp_flower_spawn_phy_reprs
net/sched: Set default of CONFIG_NET_TC_SKB_EXT to N
vrf: Do not attempt to create IPv6 mcast rule if IPv6 is disabled
net: sched: sch_sfb: don't call qdisc_put() while holding tree lock
...
First set of fixes for 5.4 sent during the merge window. Most are
regressions fixes but the mt7615 problem has been since it was merged.
iwlwifi
* fix a build regression related CONFIG_THERMAL
* avoid using GEO_TX_POWER_LIMIT command on certain firmware versions
rtw88
* fixes for skb leaks
zd1211rw
* fix a compiler warning on 32 bit
mt76
* fix the firmware paths for mt7615 to match with linux-firmware
wil6210
* fix use of skb after free
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJdjLN3AAoJEG4XJFUm622bsBcH/1A/srmEN3bME86p9j0DS1Wb
A/8KPP88q9gczIDg+uZQCw1rTqHUrqkgbPxVCa64tKdPjqioRc9nW4CVhKh2OLTy
88Bwh/mJhxfh/+TTfYf397OsHr9NEVaFnEqjYeUxtyhRoZriUmAtKSd4/689czDP
AOdbkXShe8pUS+UvpizfpOHP28j4TbFOzcWn8qcGm1gqfuCHan+giaSw073vz+r4
fagOz470huyqCwx8LB21IzTCunox20W4IfN/G2AMoKx7tE9XbYr6kRR8vawffwm2
FVyhlnibkRQnRv77thg+zJZQ6UpJybsfM8Izpn1kTDFiRChNqvMtOKboz+IQOHg=
=4i7U
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2019-09-26' of https://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 5.4
First set of fixes for 5.4 sent during the merge window. Most are
regressions fixes but the mt7615 problem has been since it was merged.
iwlwifi
* fix a build regression related CONFIG_THERMAL
* avoid using GEO_TX_POWER_LIMIT command on certain firmware versions
rtw88
* fixes for skb leaks
zd1211rw
* fix a compiler warning on 32 bit
mt76
* fix the firmware paths for mt7615 to match with linux-firmware
wil6210
* fix use of skb after free
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Adjust indentation from spaces to tab (+optional two spaces) as in
coding style with command like:
$ sed -e 's/^ /\t/' -i */Kconfig
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The debug code dereferences "skb" to print "skb->len" so we have to
print the message before we free "skb".
Fixes: f99fe49ff3 ("wil6210: add wil_netif_rx() helper function")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The intention was to have the GEO_TX_POWER_LIMIT command in FW version
36 as well, but not all 8000 family got this feature enabled. The
8000 family is the only one using version 36, so skip this version
entirely. If we try to send this command to the firmwares that do not
support it, we get a BAD_COMMAND response from the firmware.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=204151.
Cc: stable@vger.kernel.org # 4.19+
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
mt7615 patch/n9/cr4 firmwares are available in mediatek folder in
linux-firmware repository. Because of this mt7615 won't work on regular
distributions like Ubuntu. Fix path definitions. Moreover remove useless
firmware name pointers and use definitions directly
Fixes: 04b8e65922 ("mt76: add mac80211 driver for MT7615 PCIe-based chipsets")
Cc: stable@vger.kernel.org
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
After firmware has been downloaded, driver should send
some information to it through H2C commands. Those H2C
commands are transmitted through TX path.
But before HCI has been started, the TX path is not
working completely. Such as PCI interfaces, the interrupts
are not enabled, hence TX interrupts will not be issued
after H2C skb has been DMAed to the device. And the H2C
skbs will not be released until the device is powered off.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
On 32-bit:
drivers/net/wireless/zydas/zd1211rw/zd_usb.c: In function ‘check_read_regs’:
drivers/net/wireless/zydas/zd1211rw/zd_def.h:18:25: warning: format ‘%ld’ expects argument of type ‘long int’, but argument 6 has type ‘size_t’ {aka ‘unsigned int’} [-Wformat=]
dev_printk(level, dev, "%s() " fmt, __func__, ##args)
^~~~~~~
drivers/net/wireless/zydas/zd1211rw/zd_def.h:22:4: note: in expansion of macro ‘dev_printk_f’
dev_printk_f(KERN_DEBUG, dev, fmt, ## args)
^~~~~~~~~~~~
drivers/net/wireless/zydas/zd1211rw/zd_usb.c:1635:3: note: in expansion of macro ‘dev_dbg_f’
dev_dbg_f(zd_usb_dev(usb),
^~~~~~~~~
drivers/net/wireless/zydas/zd1211rw/zd_usb.c:1636:51: note: format string is defined here
"error: actual length %d less than expected %ld\n",
~~^
%d
Fixes: 84b0b66352 ("zd1211rw: zd_usb: Use struct_size() helper")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Interrupt is disabled to stop PCI, which means the skbs
queued for each TX ring will not be released via DMA
interrupt. To avoid those skbs remained being left in
the skb queue until PCI has been removed, driver needs
to release skbs by itself.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Tested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
These skbs free routines could be used when driver wants
to stop PCI bus, because some of the skbs remained in the
queue may not have been returned via DMA interrupt.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Without CONFIG_THERMAL, the driver fails to link as it calls
iwl_mvm_send_temp_report_ths_cmd() unconditionally. Fix this
by making that function available, but do almost nothing but
send the empty firmware command to enable CT-kill reporting.
While at it, also fix that function itself to not error out
when the thermal zone hasn't been initialized, but instead
just send the empty firmware command in this case as well.
Fixes: 242d9c8b9a ("iwlwifi: mvm: use FW thermal monitoring regardless of CONFIG_THERMAL")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
