This avoids setting TUNNEL_VXLAN_OPT for VXLAN frames which don't
have any GBP metadata set. It is not invalid to set it but unnecessary.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make __ipv6_select_ident() static as it isn't used outside
the file.
Fixes: 0508c07f5e (ipv6: Select fragment id during UFO segmentation if not set.)
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent commit:
0508c07f5e
Author: Vlad Yasevich <vyasevich@gmail.com>
Date: Tue Feb 3 16:36:15 2015 -0500
ipv6: Select fragment id during UFO segmentation if not set.
Introduced a bug on LE in how ipv6 fragment id is assigned.
This was cought by nightly sparce check:
Resolve the following sparce error:
net/ipv6/output_core.c:57:38: sparse: incorrect type in assignment
(different base types)
net/ipv6/output_core.c:57:38: expected restricted __be32
[usertype] ip6_frag_id
net/ipv6/output_core.c:57:38: got unsigned int [unsigned]
[assigned] [usertype] id
Fixes: 0508c07f5e (ipv6: Select fragment id during UFO segmentation if not set.)
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bridge's default_pvid adds a vid by default, by which we cannot add a
non-vlan fdb entry by default, because br_fdb_add() adds fdb entries for
all vlans instead of a non-vlan one when any vlan is configured.
# ip link add br0 type bridge
# ip link set eth0 master br0
# bridge fdb add 12:34:56:78:90:ab dev eth0 master temp
# bridge fdb show brport eth0 | grep 12:34:56:78:90:ab
12:34:56:78:90:ab dev eth0 vlan 1 static
We expect a non-vlan fdb entry as well as vlan 1:
12:34:56:78:90:ab dev eth0 static
To fix this, we need to insert a non-vlan fdb entry if vlan is not
specified, even when any vlan is configured.
Fixes: 5be5a2df40 ("bridge: Add filtering support for default_pvid")
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
dsa_slave_phy_setup() finds the phy for the port via device tree and
using of_phy_connect(), or it uses the fall back of taking a phy from
the switch internal mdio bus and calling phy_connect_direct(). Either
way, if a phy is found, phy_attach_direct() is called to attach the
phy to the slave device.
In dsa_slave_create(), a second call to phy_attach() is made. This
results in the warning "PHY already attached". Remove this second,
redundant attaching of the phy.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tipc_snprintf() was heavily utilized by the old netlink API which no
longer exists (now netlink compat).
In this patch we swap tipc_snprintf() to the identical scnprintf() in
the only remaining occurrence.
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add TIPC_CMD_NOOP to compat layer and remove the old framework.
All legacy nl commands are now converted to the compat layer in
netlink_compat.c.
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert TIPC_CMD_SHOW_STATS to compat layer. This command does not
have any counterpart in the new API, meaning it now solely exists as a
function in the compat layer.
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert TIPC_CMD_GET_NETID to compat dumpit.
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert TIPC_CMD_SET_NETID to compat doit.
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert TIPC_CMD_SET_NODE_ADDR to compat doit.
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert TIPC_CMD_GET_NODES to compat dumpit and remove global node
counter solely used by the legacy API.
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert TIPC_CMD_GET_MEDIA_NAMES to compat dumpit.
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert socket (port) listing to compat dumpit call. If a socket
(port) has publications a second dumpit call is issued to collect them
and format then into the legacy buffer before continuing to process
the sockets (ports).
Command converted in this patch:
TIPC_CMD_SHOW_PORTS
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add functionality for printing a dump header and convert
TIPC_CMD_SHOW_NAME_TABLE to compat dumpit.
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert TIPC_CMD_RESET_LINK_STATS to compat doit.
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert setting of link proprieties to compat doit calls.
Commands converted in this patch:
TIPC_CMD_SET_LINK_TOL
TIPC_CMD_SET_LINK_PRI
TIPC_CMD_SET_LINK_WINDOW
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert TIPC_CMD_GET_LINKS to compat dumpit and remove global link
counter solely used by the legacy API.
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add functionality for safely appending string data to a TLV without
keeping write count in the caller.
Convert TIPC_CMD_SHOW_LINK_STATS to compat dumpit.
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a framework for transcoding legacy nl action into actions
(.doit) calls from the new nl API. This is done by converting the
incoming TLV data into netlink data with nested netlink attributes.
Unfortunately due to the randomness of the legacy API we can't do this
generically so each legacy netlink command requires a specific
transcoding recipe. In this case for bearer enable and bearer disable.
Convert TIPC_CMD_ENABLE_BEARER and TIPC_CMD_DISABLE_BEARER into doit
compat calls.
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a framework for dumping netlink data from the new netlink
API and formatting it to the old legacy API format. This is done by
looping the dump data and calling a format handler for each entity, in
this case a bearer.
We dump until either all data is dumped or we reach the limited buffer
size of the legacy API. Remember, the legacy API doesn't scale.
In this commit we convert TIPC_CMD_GET_BEARER_NAMES to use the compat
layer.
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new netlink API is no longer "v2" but rather the standard API and
the legacy API is now "nl compat". We split them into separate
start/stop and put them in different files in order to further
distinguish them.
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the linger code is gone, the xs_tcp_fin_timeout variable has
no real function. Keep it for now, since it is part of the /proc
interface, but only define it if that /proc interface is enabled.
Suggested-by: Anna Schumaker <Anna.Schumaker@netapp.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
If the connection reset is due to an active call on our side, then
the state change is sometimes not reported. Catch those instances
using xs_error_report() instead.
Also remove the xs_tcp_shutdown() call in xs_tcp_send_request() as
the change in behaviour makes it redundant.
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Use of socket shutdown() means that we monitor the shutdown process
through the xs_tcp_state_change() callback, so it is preferable to
a full close in all cases unless we're destroying the transport.
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
The previous behaviour left the connection half-open in order to try
to scrape the last replies from the socket. Now that we have more reliable
reconnection, change the behaviour to close down the socket faster.
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Now that we no longer use the partial shutdown code when closing the
socket, we no longer need to worry about the TCP linger2 state.
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
We set the outer mode protocol too early. As a result, the
local error handler might dispatch to the wrong address family
and report the error to a wrong socket type. We fix this by
setting the outer protocol to the skb after we accessed the
inner mode for the last time, right before we do the atcual
encapsulation where we switch finally to the outer mode.
Reported-by: Chris Ruehl <chris.ruehl@gtsys.com.hk>
Tested-by: Chris Ruehl <chris.ruehl@gtsys.com.hk>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Make sure root user does not try something stupid.
Also make sure mask field in struct rps_sock_flow_table
does not share a cache line with the potentially often dirtied
flow table.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes: 567e4b7973 ("net: rfs: add hash collision detection")
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code prevents any operation with a mixed-family dest
unless IP_VS_CONN_F_TUNNEL flag is set. The problem is that it's impossible
for the client to follow this rule, because ip_vs_genl_parse_dest does
not even read the destination conn_flags when cmd = IPVS_CMD_DEL_DEST
(need_full_dest = 0).
Also, not every client can pass this flag when removing a dest. ipvsadm,
for example, does not support the "-i" command line option together with
the "-d" option.
This change disables any checks for mixed-family on IPVS_CMD_DEL_DEST command.
Signed-off-by: Alexey Andriyanov <alan@al-an.info>
Fixes: bc18d37f67 ("ipvs: Allow heterogeneous pools now that we support them")
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
Instead we rely on SO_REUSEPORT to provide the reconnection semantics
that we need for NFSv2/v3.
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
It is not safe to call xs_reset_transport() from inside xs_udp_setup_socket()
or xs_tcp_setup_socket(), since they do not own the correct locks. Instead,
do it in xs_connect().
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
The socket lock is currently held by the task that is requesting the
connection be established. While that is efficient in the case where
the connection happens quickly, it is racy in the case where it doesn't.
What we really want is for the connect helper to be able to block access
to the socket while it is being set up.
This patch does so by arranging to transfer the socket lock from the
task that is requesting the connect attempt, and then releasing that
lock once everything is done.
This scheme also gives us automatic protection against collisions with
the RPC close code, so we can kill the cancel_delayed_work_sync()
call in xs_close().
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Now that we can reuse bound ports after a close, we never really want to
clear the transport's source port after it has been set. Doing so really
messes up the NFSv3 DRC on the server.
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Now that we're setting SO_REUSEPORT, we still need to handle the
case where a connect() is attempted, but the old socket is still
lingering.
Essentially, all we want to do here is handle the error by waiting
a few seconds and then retrying.
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Receive Flow Steering is a nice solution but suffers from
hash collisions when a mix of connected and unconnected traffic
is received on the host, when flow hash table is populated.
Also, clearing flow in inet_release() makes RFS not very good
for short lived flows, as many packets can follow close().
(FIN , ACK packets, ...)
This patch extends the information stored into global hash table
to not only include cpu number, but upper part of the hash value.
I use a 32bit value, and dynamically split it in two parts.
For host with less than 64 possible cpus, this gives 6 bits for the
cpu number, and 26 (32-6) bits for the upper part of the hash.
Since hash bucket selection use low order bits of the hash, we have
a full hash match, if /proc/sys/net/core/rps_sock_flow_entries is big
enough.
If the hash found in flow table does not match, we fallback to RPS (if
it is enabled for the rxqueue).
This means that a packet for an non connected flow can avoid the
IPI through a unrelated/victim CPU.
This also means we no longer have to clear the table at socket
close time, and this helps short lived flows performance.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
encap.sport and encap.dport are __be16, use nla_{get,put}_be16 instead
of nla_{get,put}_u16.
Fixes the sparse warnings:
warning: incorrect type in assignment (different base types)
expected restricted __be32 [addressable] [usertype] o_key
got restricted __be16 [addressable] [usertype] i_flags
warning: incorrect type in assignment (different base types)
expected restricted __be16 [usertype] sport
got unsigned short
warning: incorrect type in assignment (different base types)
expected restricted __be16 [usertype] dport
got unsigned short
warning: incorrect type in argument 3 (different base types)
expected unsigned short [unsigned] [usertype] value
got restricted __be16 [usertype] sport
warning: incorrect type in argument 3 (different base types)
expected unsigned short [unsigned] [usertype] value
got restricted __be16 [usertype] dport
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using TCP, we need the ability to reuse port numbers after
a disconnection, so that the NFSv3 server knows that we're the same
client. Currently we use a hack to work around the TCP socket's
TIME_WAIT: we send an RST instead of closing, which doesn't
always work...
The SO_REUSEPORT option added in Linux 3.9 allows us to bind multiple
TCP connections to the same source address+port combination, and thus
to use ordinary TCP close() instead of the current hack.
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
In commit c637c10355 ("tipc: resolve race
problem at unicast message reception") we introduced a time limit
for how long the function tipc_sk_eneque() would be allowed to execute
its loop. Unfortunately, the test for when this limit is passed was put
in the wrong place, resulting in a lost message when the test is true.
We fix this by moving the test to before we dequeue the next buffer
from the input queue.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rt6_probe allocates a struct __rt6_probe_work and schedules a work handler rt6_probe_deferred.
But rt6_probe_deferred kfree's the struct work_struct instead of struct __rt6_probe_work.
This works, because struct work_struct is the first element of struct __rt6_probe_work.
Change it to kfree struct __rt6_probe_work to not implicitly depend on
struct work_struct being the first element.
This does not affect the generated code.
Signed-off-by: Michael Buesch <m@bues.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a sparse warning in the initial submission.
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=3fRY
-----END PGP SIGNATURE-----
Merge tag 'nfs-rdma-for-3.20-part-2' of git://git.linux-nfs.org/projects/anna/nfs-rdma
NFS: RDMA Client Sparse Fixes
This patch fixes a sparse warning in the initial submission.
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
* tag 'nfs-rdma-for-3.20-part-2' of git://git.linux-nfs.org/projects/anna/nfs-rdma:
xprtrdma: Address sparse complaint in rpcr_to_rdmar()
Ensure that in state FIN_WAIT2 or TIME_WAIT, where the connection is
represented by a tcp_timewait_sock, we rate limit dupacks in response
to incoming packets (a) with TCP timestamps that fail PAWS checks, or
(b) with sequence numbers that are out of the acceptable window.
We do not send a dupack in response to out-of-window packets if it has
been less than sysctl_tcp_invalid_ratelimit (default 500ms) since we
last sent a dupack in response to an out-of-window packet.
Reported-by: Avery Fay <avery@mixpanel.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ensure that in state ESTABLISHED, where the connection is represented
by a tcp_sock, we rate limit dupacks in response to incoming packets
(a) with TCP timestamps that fail PAWS checks, or (b) with sequence
numbers or ACK numbers that are out of the acceptable window.
We do not send a dupack in response to out-of-window packets if it has
been less than sysctl_tcp_invalid_ratelimit (default 500ms) since we
last sent a dupack in response to an out-of-window packet.
There is already a similar (although global) rate-limiting mechanism
for "challenge ACKs". When deciding whether to send a challence ACK,
we first consult the new per-connection rate limit, and then the
global rate limit.
Reported-by: Avery Fay <avery@mixpanel.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the SYN_RECV state, where the TCP connection is represented by
tcp_request_sock, we now rate-limit SYNACKs in response to a client's
retransmitted SYNs: we do not send a SYNACK in response to client SYN
if it has been less than sysctl_tcp_invalid_ratelimit (default 500ms)
since we last sent a SYNACK in response to a client's retransmitted
SYN.
This allows the vast majority of legitimate client connections to
proceed unimpeded, even for the most aggressive platforms, iOS and
MacOS, which actually retransmit SYNs 1-second intervals for several
times in a row. They use SYN RTO timeouts following the progression:
1,1,1,1,1,2,4,8,16,32.
Reported-by: Avery Fay <avery@mixpanel.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Helpers for mitigating ACK loops by rate-limiting dupacks sent in
response to incoming out-of-window packets.
This patch includes:
- rate-limiting logic
- sysctl to control how often we allow dupacks to out-of-window packets
- SNMP counter for cases where we rate-limited our dupack sending
The rate-limiting logic in this patch decides to not send dupacks in
response to out-of-window segments if (a) they are SYNs or pure ACKs
and (b) the remote endpoint is sending them faster than the configured
rate limit.
We rate-limit our responses rather than blocking them entirely or
resetting the connection, because legitimate connections can rely on
dupacks in response to some out-of-window segments. For example, zero
window probes are typically sent with a sequence number that is below
the current window, and ZWPs thus expect to thus elicit a dupack in
response.
We allow dupacks in response to TCP segments with data, because these
may be spurious retransmissions for which the remote endpoint wants to
receive DSACKs. This is safe because segments with data can't
realistically be part of ACK loops, which by their nature consist of
each side sending pure/data-less ACKs to each other.
The dupack interval is controlled by a new sysctl knob,
tcp_invalid_ratelimit, given in milliseconds, in case an administrator
needs to dial this upward in the face of a high-rate DoS attack. The
name and units are chosen to be analogous to the existing analogous
knob for ICMP, icmp_ratelimit.
The default value for tcp_invalid_ratelimit is 500ms, which allows at
most one such dupack per 500ms. This is chosen to be 2x faster than
the 1-second minimum RTO interval allowed by RFC 6298 (section 2, rule
2.4). We allow the extra 2x factor because network delay variations
can cause packets sent at 1 second intervals to be compressed and
arrive much closer.
Reported-by: Avery Fay <avery@mixpanel.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a missing bridge port check caught by smatch.
setlink/dellink of attributes like vlans can come for a bridge device
and there is no need to offload those today. So, this patch adds a bridge
port check. (In these cases however, the BRIDGE_SELF flags will always be set
and we may not hit a problem with the current code).
smatch complaint:
The patch 68e331c785: "bridge: offload bridge port attributes to
switch asic if feature flag set" from Jan 29, 2015, leads to the
following Smatch complaint:
net/bridge/br_netlink.c:552 br_setlink()
error: we previously assumed 'p' could be null (see line 518)
net/bridge/br_netlink.c
517
518 if (p && protinfo) {
^
Check for NULL.
Reported-By: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hotpluging a cpu might be rare, yet we have to use proper
handlers when taking over packets found in backlog queues.
dev_cpu_callback() runs from process context, thus we should
call netif_rx_ni() to properly invoke softirq handler.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 083735f4b0 ("rds: switch rds_message_copy_from_user() to iov_iter")
breaks rds_message_copy_from_user() semantics on success, and causes it
to return nbytes copied, when it should return 0. This commit fixes that bug.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The macro rdsdebug is defined as
pr_debug("%s(): " fmt, __func__ , ##args)
Hence it doesn't make sense to include the name of the calling
function explicitly in the format string passed to rdsdebug.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
OVS userspace already probes the openvswitch kernel module for
OVS_ACTION_ATTR_SET_MASKED support. This patch adds the kernel module
implementation of masked set actions.
The existing set action sets many fields at once. When only a subset
of the IP header fields, for example, should be modified, all the IP
fields need to be exact matched so that the other field values can be
copied to the set action. A masked set action allows modification of
an arbitrary subset of the supported header bits without requiring the
rest to be matched.
Masked set action is now supported for all writeable key types, except
for the tunnel key. The set tunnel action is an exception as any
input tunnel info is cleared before action processing starts, so there
is no tunnel info to mask.
The kernel module converts all (non-tunnel) set actions to masked set
actions. This makes action processing more uniform, and results in
less branching and duplicating the action processing code. When
returning actions to userspace, the fully masked set actions are
converted back to normal set actions. We use a kernel internal action
code to be able to tell the userspace provided and converted masked
set actions apart.
Signed-off-by: Jarno Rajahalme <jrajahalme@nicira.com>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the second NFC pull request for 3.20.
It brings:
- NCI NFCEE (NFC Execution Environment, typically an embedded or
external secure element) discovery and enabling/disabling support.
In order to communicate with an NFCEE, we also added NCI's logical
connections support to the NCI stack.
- HCI over NCI protocol support. Some secure elements only understand
HCI and thus we need to send them HCI frames when they're part of
an NCI chipset.
- NFC_EVT_TRANSACTION userspace API addition. Whenever an application
running on a secure element needs to notify its host counterpart,
we send an NFC_EVENT_SE_TRANSACTION event to userspace through the
NFC netlink socket.
- Secure element and HCI transaction event support for the st21nfcb
chipset.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=8caD
-----END PGP SIGNATURE-----
Merge tag 'nfc-next-3.20-2' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/nfc-next
NFC: 3.20 second pull request
This is the second NFC pull request for 3.20.
It brings:
- NCI NFCEE (NFC Execution Environment, typically an embedded or
external secure element) discovery and enabling/disabling support.
In order to communicate with an NFCEE, we also added NCI's logical
connections support to the NCI stack.
- HCI over NCI protocol support. Some secure elements only understand
HCI and thus we need to send them HCI frames when they're part of
an NCI chipset.
- NFC_EVT_TRANSACTION userspace API addition. Whenever an application
running on a secure element needs to notify its host counterpart,
we send an NFC_EVENT_SE_TRANSACTION event to userspace through the
NFC netlink socket.
- Secure element and HCI transaction event support for the st21nfcb
chipset.
Signed-off-by: David S. Miller <davem@davemloft.net>
ifla_vf_policy[] is wrong in advertising its individual member types as
NLA_BINARY since .type = NLA_BINARY in combination with .len declares the
len member as *max* attribute length [0, len].
The issue is that when do_setvfinfo() is being called to set up a VF
through ndo handler, we could set corrupted data if the attribute length
is less than the size of the related structure itself.
The intent is exactly the opposite, namely to make sure to pass at least
data of minimum size of len.
Fixes: ebc08a6f47 ("rtnetlink: Add VF config code to rtnetlink")
Cc: Mitch Williams <mitch.a.williams@intel.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The number of connected switches was sourced from the number of
children to the DSA node, change it to the number of available
children, skipping any disabled switches.
Fixes: 5e95329b70 ("dsa: add device tree bindings to register DSA switches")
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We still need a validate_link_af() handler with an appropriate nla policy,
similarly as we have in IPv4 case, otherwise size validations are not being
done properly in that case.
Fixes: f53adae4ea ("net: ipv6: add tokenized interface identifier support")
Fixes: bc91b0f07a ("ipv6: addrconf: implement address generation modes")
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a network-layer header has multiple IPv6 extension headers, then offset
for mobility header goes wrong. This regression breaks an xfrm policy lookup
for a particular receive packet. Binding update packets of Mobile IPv6
are all discarded without this fix.
Fixes: de3b7a06df ("xfrm6: Fix transport header offset in _decode_session6.")
Signed-off-by: Hajime Tazaki <tazaki@sfc.wide.ad.jp>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
In a previous commit in this series we resolved a race problem during
unicast message reception.
Here, we resolve the same problem at multicast reception. We apply the
same technique: an input queue serializing the delivery of arriving
buffers. The main difference is that here we do it in two steps.
First, the broadcast link feeds arriving buffers into the tail of an
arrival queue, which head is consumed at the socket level, and where
destination lookup is performed. Second, if the lookup is successful,
the resulting buffer clones are fed into a second queue, the input
queue. This queue is consumed at reception in the socket just like
in the unicast case. Both queues are protected by the same lock, -the
one of the input queue.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The structure 'tipc_port_list' is used to collect port numbers
representing multicast destination socket on a receiving node.
The list is not based on a standard linked list, and is in reality
optimized for the uncommon case that there are more than one
multicast destinations per node. This makes the list handling
unecessarily complex, and as a consequence, even the socket
multicast reception becomes more complex.
In this commit, we replace 'tipc_port_list' with a new 'struct
tipc_plist', which is based on a standard list. We give the new
list stack (push/pop) semantics, someting that simplifies
the implementation of the function tipc_sk_mcast_rcv().
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new input message queue in struct tipc_link can be used for
delivering connection abort messages to subscribing sockets. This
makes it possible to simplify the code for such cases.
This commit removes the temporary list in tipc_node_unlock()
used for transforming abort subscriptions to messages. Instead, the
abort messages are now created at the moment of lost contact, and
then added to the last failed link's generic input queue for delivery
to the sockets concerned.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TIPC handles message cardinality and sequencing at the link layer,
before passing messages upwards to the destination sockets. During the
upcall from link to socket no locks are held. It is therefore possible,
and we see it happen occasionally, that messages arriving in different
threads and delivered in sequence still bypass each other before they
reach the destination socket. This must not happen, since it violates
the sequentiality guarantee.
We solve this by adding a new input buffer queue to the link structure.
Arriving messages are added safely to the tail of that queue by the
link, while the head of the queue is consumed, also safely, by the
receiving socket. Sequentiality is secured per socket by only allowing
buffers to be dequeued inside the socket lock. Since there may be multiple
simultaneous readers of the queue, we use a 'filter' parameter to reduce
the risk that they peek the same buffer from the queue, hence also
reducing the risk of contention on the receiving socket locks.
This solves the sequentiality problem, and seems to cause no measurable
performance degradation.
A nice side effect of this change is that lock handling in the functions
tipc_rcv() and tipc_bcast_rcv() now becomes uniform, something that
will enable future simplifications of those functions.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The list for outgoing traffic buffers from a socket is currently
allocated on the stack. This forces us to initialize the queue for
each sent message, something costing extra CPU cycles in the most
critical data path. Later in this series we will introduce a new
safe input buffer queue, something that would force us to initialize
even the spinlock of the outgoing queue. A closer analysis reveals
that the queue always is filled and emptied within the same lock_sock()
session. It is therefore safe to use a queue aggregated in the socket
itself for this purpose. Since there already exists a queue for this
in struct sock, sk_write_queue, we introduce use of that queue in
this commit.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function tipc_msg_eval() is in reality doing two related, but
different tasks. First it tries to find a new destination for named
messages, in case there was no first lookup, or if the first lookup
failed. Second, it does what its name suggests, evaluating the validity
of the message and its destination, and returning an appropriate error
code depending on the result.
This is confusing, and in this commit we choose to break it up into two
functions. A new function, tipc_msg_lookup_dest(), first attempts to find
a new destination, if the message is of the right type. If this lookup
fails, or if the message should not be subject to a second lookup, the
already existing tipc_msg_reverse() is called. This function performs
prepares the message for rejection, if applicable.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code for enqueuing arriving buffers in the function tipc_sk_rcv()
contains long code lines and currently goes to two indentation levels.
As a cosmetic preparaton for the next commits, we break it out into
a separate function.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Despite recent improvements, the handling of error codes and return
values at reception of messages in the socket layer is still confusing.
In this commit, we try to make it more comprehensible. First, we
separate between the return values coming from the functions called
by tipc_sk_rcv(), -those are TIPC specific error codes, and the
return values returned by tipc_sk_rcv() itself. Second, we don't
use the returned TIPC error code as indication for whether a buffer
should be forwarded/rejected or not; instead we use the buffer pointer
passed along with filter_msg(). This separation is necessary because
we sometimes want to forward messages even when there is no error
(i.e., protocol messages and successfully secondary looked up data
messages).
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The most common usage of namespace information is when we fetch the
own node addess from the net structure. This leads to a lot of
passing around of a parameter of type 'struct net *' between
functions just to make them able to obtain this address.
However, in many cases this is unnecessary. The own node address
is readily available as a member of both struct tipc_sock and
tipc_link, and can be fetched from there instead.
The fact that the vast majority of functions in socket.c and link.c
anyway are maintaining a pointer to their respective base structures
makes this option even more compelling.
In this commit, we introduce the inline functions tsk_own_node()
and link_own_node() to make it easy for functions to fetch the node
address from those structs instead of having to pass along and
dereference the namespace struct.
In particular, we make calls to the msg_xx() functions in msg.{h,c}
context independent by directly passing them the own node address
as parameter when needed. Those functions should be regarded as
leaves in the code dependency tree, and it is hence desirable to
keep them namspace unaware.
Apart from a potential positive effect on cache behavior, these
changes make it easier to introduce the changes that will follow
later in this series.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes two issues in UDP checksum computation in pktgen.
First, the pseudo-header uses the source and destination IP
addresses. Currently, the ports are used for IPv4.
Second, the UDP checksum covers both header and data. So we need to
generate the data earlier (move pktgen_finalize_skb up), and compute
the checksum for UDP header + data.
Fixes: c26bf4a513 ("pktgen: Add UDPCSUM flag to support UDP checksums")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC 4429 ("Optimistic DAD") states that optimistic addresses
should be treated as deprecated addresses. From section 2.1:
Unless noted otherwise, components of the IPv6 protocol stack
should treat addresses in the Optimistic state equivalently to
those in the Deprecated state, indicating that the address is
available for use but should not be used if another suitable
address is available.
Optimistic addresses are indeed avoided when other addresses are
available (i.e. at source address selection time), but they have
not heretofore been available for things like explicit bind() and
sendmsg() with struct in6_pktinfo, etc.
This change makes optimistic addresses treated more like
deprecated addresses than tentative ones.
Signed-off-by: Erik Kline <ek@google.com>
Acked-by: Lorenzo Colitti <lorenzo@google.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
flow_cache_flush_task references a structure member flow_cache_gc_work
where it should reference flow_cache_flush_task instead.
Kernel panic occurs on kernels using IPsec during XFRM garbage
collection. The garbage collection interval can be shortened using the
following sysctl settings:
net.ipv4.xfrm4_gc_thresh=4
net.ipv6.xfrm6_gc_thresh=4
With the default settings, our productions servers crash approximately
once a week. With the settings above, they crash immediately.
Fixes: ca925cf153 ("flowcache: Make flow cache name space aware")
Reported-by: Tomáš Charvát <tc@excello.cz>
Tested-by: Jan Hejl <jh@excello.cz>
Signed-off-by: Miroslav Urbanek <mu@miroslavurbanek.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/vxlan.c
drivers/vhost/net.c
include/linux/if_vlan.h
net/core/dev.c
The net/core/dev.c conflict was the overlap of one commit marking an
existing function static whilst another was adding a new function.
In the include/linux/if_vlan.h case, the type used for a local
variable was changed in 'net', whereas the function got rewritten
to fix a stacked vlan bug in 'net-next'.
In drivers/vhost/net.c, Al Viro's iov_iter conversions in 'net-next'
overlapped with an endainness fix for VHOST 1.0 in 'net'.
In drivers/net/vxlan.c, vxlan_find_vni() added a 'flags' parameter
in 'net-next' whereas in 'net' there was a bug fix to pass in the
correct network namespace pointer in calls to this function.
Signed-off-by: David S. Miller <davem@davemloft.net>
With "make ARCH=x86_64 allmodconfig make C=1 CF=-D__CHECK_ENDIAN__":
linux-2.6/net/sunrpc/xprtrdma/xprt_rdma.h:273:30: warning: incorrect
type in initializer (different base types)
linux-2.6/net/sunrpc/xprtrdma/xprt_rdma.h:273:30: expected restricted
__be32 [usertype] *buffer
linux-2.6/net/sunrpc/xprtrdma/xprt_rdma.h:273:30: got unsigned int
[usertype] *rq_buffer
As far as I can tell this is a false positive.
Reported-by: kbuild-all@01.org
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Fixes following sparse warnings :
net/ipv6/sit.c:1509:32: warning: incorrect type in assignment (different base types)
net/ipv6/sit.c:1509:32: expected restricted __be16 [usertype] sport
net/ipv6/sit.c:1509:32: got unsigned short
net/ipv6/sit.c:1514:32: warning: incorrect type in assignment (different base types)
net/ipv6/sit.c:1514:32: expected restricted __be16 [usertype] dport
net/ipv6/sit.c:1514:32: got unsigned short
net/ipv6/sit.c:1711:38: warning: incorrect type in argument 3 (different base types)
net/ipv6/sit.c:1711:38: expected unsigned short [unsigned] [usertype] value
net/ipv6/sit.c:1711:38: got restricted __be16 [usertype] sport
net/ipv6/sit.c:1713:38: warning: incorrect type in argument 3 (different base types)
net/ipv6/sit.c:1713:38: expected unsigned short [unsigned] [usertype] value
net/ipv6/sit.c:1713:38: got restricted __be16 [usertype] dport
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netdev_adjacent_add_links() and netdev_adjacent_del_links()
are static.
queue->qdisc has __rcu annotation, need to use RCU_INIT_POINTER()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
info is in network byte order, change it back to host byte order
before use. In particular, the current code sets the MTU of the tunnel
to a wrong (too big) value.
Fixes: c12b395a46 ("gre: Support GRE over IPv6")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FQ has a fast path for skb attached to a socket, as it does not
have to compute a flow hash. But for other packets, FQ being non
stochastic means that hosts exposed to random Internet traffic
can allocate million of flows structure (104 bytes each) pretty
easily. Not only host can OOM, but lookup in RB trees can take
too much cpu and memory resources.
This patch adds a new attribute, orphan_mask, that is adding
possibility of having a stochastic hash for orphaned skb.
Its default value is 1024 slots, to mimic SFQ behavior.
Note: This does not apply to locally generated TCP traffic,
and no locally generated traffic will share a flow structure
with another perfect or stochastic flow.
This patch also handles the specific case of SYNACK messages:
They are attached to the listener socket, and therefore all map
to a single hash bucket. If listener have set SO_MAX_PACING_RATE,
hoping to have new accepted socket inherit this rate, SYNACK
might be paced and even dropped.
This is very similar to an internal patch Google have used more
than one year.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we added pacing to TCP, we decided to let sch_fq take care
of actual pacing.
All TCP had to do was to compute sk->pacing_rate using simple formula:
sk->pacing_rate = 2 * cwnd * mss / rtt
It works well for senders (bulk flows), but not very well for receivers
or even RPC :
cwnd on the receiver can be less than 10, rtt can be around 100ms, so we
can end up pacing ACK packets, slowing down the sender.
Really, only the sender should pace, according to its own logic.
Instead of adding a new bit in skb, or call yet another flow
dissection, we tweak skb->truesize to a small value (2), and
we instruct sch_fq to use new helper and not pace pure ack.
Note this also helps TCP small queue, as ack packets present
in qdisc/NIC do not prevent sending a data packet (RPC workload)
This helps to reduce tx completion overhead, ack packets can use regular
sock_wfree() instead of tcp_wfree() which is a bit more expensive.
This has no impact in the case packets are sent to loopback interface,
as we do not coalesce ack packets (were we would detect skb->truesize
lie)
In case netem (with a delay) is used, skb_orphan_partial() also sets
skb->truesize to 1.
This patch is a combination of two patches we used for about one year at
Google.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch gets rid of the manual rhashtable walk in nft_hash
which touches rhashtable internals that should not be exposed.
It does so by using the rhashtable iterator primitives.
Note that I'm leaving nft_hash_destroy alone since it's only
invoked on shutdown and it shouldn't be affected by changes
to rhashtable internals (or at least not what I'm planning to
change).
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch gets rid of the manual rhashtable walk in netlink
which touches rhashtable internals that should not be exposed.
It does so by using the rhashtable iterator primitives.
In fact the existing code was very buggy. Some sockets weren't
shown at all while others were shown more than once.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
In tcf_exts_dump_stats(), ensure that exts->actions is not empty before
accessing the first element of that list and calling tcf_action_copy_stats()
on it. This fixes some random segvs when adding filters of type "basic" with
no particular action.
This also fixes the dumping of those "no-action" filters, which more often
than not made calls to tcf_action_copy_stats() fail and consequently netlink
attributes added by the caller to be removed by a call to nla_nest_cancel().
Fixes: 33be627159 ("net_sched: act: use standard struct list_head")
Signed-off-by: Ignacy Gawędzki <ignacy.gawedzki@green-communications.fr>
Acked-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Configuring fq with quantum 0 hangs the system, presumably because of a
non-interruptible infinite loop. Either way quantum 0 does not make sense.
Reproduce with:
sudo tc qdisc add dev lo root fq quantum 0 initial_quantum 0
ping 127.0.0.1
Signed-off-by: Kenneth Klette Jonassen <kennetkl@ifi.uio.no>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add event which provides an indication on a change in the state
of a bonding slave. The event handler should cast the pointer to the
appropriate type (struct netdev_bonding_info) in order to get the
full info about the slave.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a new link instance is created, it is trigged to start by
sending it a TIPC_STARTING_EVT, whereafter a regular link
reset is applied to it.
The starting event is codewise treated as a timeout event, and prompts
a link RESET message to be sent to the peer node, carrying a link
session identifier. The later link_reset() call nudges this session
identifier, whereafter all subsequent RESET messages will be sent out
with the new identifier. The latter session number overrides the former,
causing the peer to unconditionally accept it irrespective of its
current working state.
We don't think that this causes any problem, but it is not in accordance
with the protocol spec, and may cause confusion when debugging TIPC
sessions.
To avoid this, we make the starting event distinct from the
subsequent timeout events, by not allowing the former to send
out any RESET message. This eliminates the described problem.
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instances of struct node are created in the function tipc_disc_rcv()
under the assumption that there is no race between received discovery
messages arriving from the same node. This assumption is wrong.
When we use more than one bearer, it is possible that discovery
messages from the same node arrive at the same moment, resulting in
creation of two instances of struct tipc_node. This may later cause
confusion during link establishment, and may result in one of the links
never becoming activated.
We fix this by making lookup and potential creation of nodes atomic.
Instead of first looking up the node, and in case of failure, create it,
we now start with looking up the node inside node_link_create(), and
return a reference to that one if found. Otherwise, we go ahead and
create the node as we did before.
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During link failover it may happen that the remaining link goes
down while it is still in the process of taking over traffic
from a previously failed link. When this happens, we currently
abort the failover procedure and reset the first failed link to
non-failover mode, so that it will be ready to re-establish
contact with its peer when it comes available.
However, if the first link goes down because its bearer was manually
disabled, it is not enough to reset it; it must also be deleted;
which is supposed to happen when the failover procedure is finished.
Otherwise it will remain a zombie link: attached to the owner node
structure, in mode LINK_STOPPED, and permanently blocking any re-
establishing of the link to the peer via the interface in question.
We fix this by amending the failover abort procedure. Apart from
resetting the link to non-failover state, we test if the link is
also in LINK_STOPPED mode. If so, we delete it, using the conditional
tipc_link_delete() function introduced in the previous commit.
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a bearer is disabled, all pertaining links will be reset and
deleted. However, if there is a second active link towards a killed
link's destination, the delete has to be postponed until the failover
is finished. During this interval, we currently put the link in zombie
mode, i.e., we take it out of traffic, delete its timer, but leave it
attached to the owner node structure until all missing packets have
been received. When this is done, we detach the link from its node
and delete it, assuming that the synchronous timer deletion that was
initiated earlier in a different thread has finished.
This is unsafe, as the failover may finish before del_timer_sync()
has returned in the other thread.
We fix this by adding an atomic reference counter of type kref in
struct tipc_link. The counter keeps track of the references kept
to the link by the owner node and the timer. We then do a conditional
delete, based on the reference counter, both after the failover has
been finished and when the timer expires, if applicable. Whoever
comes last, will actually delete the link. This approach also implies
that we can make the deletion of the timer asynchronous.
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Max unacked packets/bytes is an int while sizeof(long) was used in the
sysctl table.
This means that when they were getting read we'd also leak kernel memory
to userspace along with the timeout values.
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* revert a patch that caused a regression with mesh userspace (Bob)
* fix a number of suspend/resume related races
(from Emmanuel, Luca and myself - we'll look at backporting later)
* add software implementations for new ciphers (Jouni)
* add a new ACPI ID for Broadcom's rfkill (Mika)
* allow using netns FD for wireless (Vadim)
* some other cleanups (various)
-----BEGIN PGP SIGNATURE-----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=wOaR
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2015-02-03' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Last round of updates for net-next:
* revert a patch that caused a regression with mesh userspace (Bob)
* fix a number of suspend/resume related races
(from Emmanuel, Luca and myself - we'll look at backporting later)
* add software implementations for new ciphers (Jouni)
* add a new ACPI ID for Broadcom's rfkill (Mika)
* allow using netns FD for wireless (Vadim)
* some other cleanups (various)
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
pull request: bluetooth-next 2015-02-03
Here's what's likely the last bluetooth-next pull request for 3.20.
Notable changes include:
- xHCI workaround + a new id for the ath3k driver
- Several new ids for the btusb driver
- Support for new Intel Bluetooth controllers
- Minor cleanups to ieee802154 code
- Nested sleep warning fix in socket accept() code path
- Fixes for Out of Band pairing handling
- Support for LE scan restarting for HCI_QUIRK_STRICT_DUPLICATE_FILTER
- Improvements to data we expose through debugfs
- Proper handling of Hardware Error HCI events
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds skb_remcsum_process and skb_gro_remcsum_process to
perform the appropriate adjustments to the skb when receiving
remote checksum offload.
Updated vxlan and gue to use these functions.
Tested: Ran TCP_RR and TCP_STREAM netperf for VXLAN and GUE, did
not see any change in performance.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When 'learned_sync' flag is turned on, the offloaded switch
port syncs learned MAC addresses to bridge's FDB via switchdev notifier
(NETDEV_SWITCH_FDB_ADD). Currently, FDB entries learnt via this mechanism are
wrongly being deleted by bridge aging logic. This patch ensures that FDB
entries synced from offloaded switch ports are not deleted by bridging logic.
Such entries can only be deleted via switchdev notifier
(NETDEV_SWITCH_FDB_DEL).
Signed-off-by: Siva Mannem <siva.mannem.lnx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A typical qdisc setup is the following :
bond0 : bonding device, using HTB hierarchy
eth1/eth2 : slaves, multiqueue NIC, using MQ + FQ qdisc
XPS allows to spread packets on specific tx queues, based on the cpu
doing the send.
Problem is that dequeues from bond0 qdisc can happen on random cpus,
due to the fact that qdisc_run() can dequeue a batch of packets.
CPUA -> queue packet P1 on bond0 qdisc, P1->ooo_okay=1
CPUA -> queue packet P2 on bond0 qdisc, P2->ooo_okay=0
CPUB -> dequeue packet P1 from bond0
enqueue packet on eth1/eth2
CPUC -> dequeue packet P2 from bond0
enqueue packet on eth1/eth2 using sk cache (ooo_okay is 0)
get_xps_queue() then might select wrong queue for P1, since current cpu
might be different than CPUA.
P2 might be sent on the old queue (stored in sk->sk_tx_queue_mapping),
if CPUC runs a bit faster (or CPUB spins a bit on qdisc lock)
Effect of this bug is TCP reorders, and more generally not optimal
TX queue placement. (A victim bulk flow can be migrated to the wrong TX
queue for a while)
To fix this, we have to record sender cpu number the first time
dev_queue_xmit() is called for one tx skb.
We can union napi_id (used on receive path) and sender_cpu,
granted we clear sender_cpu in skb_scrub_packet() (credit to Willem for
this union idea)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Nandita Dukkipati <nanditad@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NFCEE_DISCOVER_CMD is a specified NCI command used to discover
NFCEE IDs.
Move nci_nfcee_discover() call to nci_discover_se() in order to
guarantee:
- NFCEE_DISCOVER_CMD run when the NCI state machine is initialized
- NFCEE_DISCOVER_CMD is not run in case there is not discover_se
hook defined by a NFC device driver.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
conn_info is currently allocated only after nfcee_discovery_ntf
which is not generic enough for logical connection other than
NFCEE. The corresponding conn_info is now created in
nci_core_conn_create_rsp().
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
For consistency sake change nci_core_conn_create_rsp structure
credits field to credits_cnt.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The current implementation limits nci_core_conn_create_req()
to only manage NCI_DESTINATION_NFCEE.
Add new parameters to nci_core_conn_create() to support all
destination types described in the NCI specification.
Because there are some parameters with variable size dynamic
buffer allocation is needed.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The NCI_STATIC_RF_CONN_ID logical connection is the most used
connection. Keeping it directly accessible in the nci_dev
structure will simplify and optimize the access.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
If the IPv6 fragment id has not been set and we perform
fragmentation due to UFO, select a new fragment id.
We now consider a fragment id of 0 as unset and if id selection
process returns 0 (after all the pertrubations), we set it to
0x80000000, thus giving us ample space not to create collisions
with the next packet we may have to fragment.
When doing UFO integrity checking, we also select the
fragment id if it has not be set yet. This is stored into
the skb_shinfo() thus allowing UFO to function correclty.
This patch also removes duplicate fragment id generation code
and moves ipv6_select_ident() into the header as it may be
used during GSO.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This one needs to copy the same data from user potentially more than
once. Sadly, MTU changes can trigger that ;-/
Cc: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
That takes care of the majority of ->sendmsg() instances - most of them
via memcpy_to_msg() or assorted getfrag() callbacks. One place where we
still keep memcpy_fromiovecend() is tipc - there we potentially read the
same data over and over; separate patch, that...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
patch is actually smaller than it seems to be - most of it is unindenting
the inner loop body in tcp_sendmsg() itself...
the bit in tcp_input.c is going to get reverted very soon - that's what
memcpy_from_msg() will become, but not in this commit; let's keep it
reasonably contained...
There's one potentially subtle change here: in case of short copy from
userland, mainline tcp_send_syn_data() discards the skb it has allocated
and falls back to normal path, where we'll send as much as possible after
rereading the same data again. This patch trims SYN+data skb instead -
that way we don't need to copy from the same place twice.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Use iov_iter_kvec() there, get rid of set_fs() games - now that
rxrpc_send_data() uses iov_iter primitives, it'll handle ITER_KVEC just
fine.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Convert skb_add_data() to iov_iter; allows to get rid of the explicit
messing with iovec in its only caller - skb_add_data() will keep advancing
->msg_iter for us, so there's no need to similate that manually.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
As it is, zero msg_iovlen means that the first iovec in the kernel
array of iovecs is left uninitialized, so checking if its ->iov_base
is NULL is random. Since the real users of that thing are doing
sendto(fd, NULL, 0, ...), they are getting msg_iovlen = 1 and
msg_iov[0] = {NULL, 0}, which is what this test is trying to catch.
As suggested by davem, let's just check that msg_iovlen was 1 and
msg_iov[0].iov_base was NULL - _that_ is well-defined and it catches
what we want to catch.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The functions "cipso_v4_doi_putdef" and "kfree" could be called in some cases
by the netlbl_mgmt_add_common() function during error handling even if the
passed variables contained still a null pointer.
* This implementation detail could be improved by adjustments for jump labels.
* Let us return immediately after the first failed function call according to
the current Linux coding style convention.
* Let us delete also an unnecessary check for the variable "entry" there.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cipso_v4_doi_free() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cipso_v4_doi_putdef() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix an Oopsable condition when nsm_mon_unmon is called as part of the
namespace cleanup, which now apparently happens after the utsname
has been freed.
Link: http://lkml.kernel.org/r/20150125220604.090121ae@neptune.home
Reported-by: Bruno Prémont <bonbons@linux-vserver.org>
Cc: stable@vger.kernel.org # 3.18
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
* flexfiles: (53 commits)
pnfs: lookup new lseg at lseg boundary
nfs41: .init_read and .init_write can be called with valid pg_lseg
pnfs: Update documentation on the Layout Drivers
pnfs/flexfiles: Add the FlexFile Layout Driver
nfs: count DIO good bytes correctly with mirroring
nfs41: wait for LAYOUTRETURN before retrying LAYOUTGET
nfs: add a helper to set NFS_ODIRECT_RESCHED_WRITES to direct writes
nfs41: add NFS_LAYOUT_RETRY_LAYOUTGET to layout header flags
nfs/flexfiles: send layoutreturn before freeing lseg
nfs41: introduce NFS_LAYOUT_RETURN_BEFORE_CLOSE
nfs41: allow async version layoutreturn
nfs41: add range to layoutreturn args
pnfs: allow LD to ask to resend read through pnfs
nfs: add nfs_pgio_current_mirror helper
nfs: only reset desc->pg_mirror_idx when mirroring is supported
nfs41: add a debug warning if we destroy an unempty layout
pnfs: fail comparison when bucket verifier not set
nfs: mirroring support for direct io
nfs: add mirroring support to pgio layer
pnfs: pass ds_commit_idx through the commit path
...
Conflicts:
fs/nfs/pnfs.c
fs/nfs/pnfs.h
Add a call to tally stats for a task under a different statsidx than
what's contained in the task structure.
This is needed to properly account for pnfs reads/writes when the
DS nfs version != the MDS version.
Signed-off-by: Weston Andros Adamson <dros@primarydata.com>
Signed-off-by: Tom Haynes <Thomas.Haynes@primarydata.com>
These patches improve the scalability of the NFSoRDMA client and take large
variables off of the stack. Additionally, the GFP_* flags are updated to
match what TCP uses.
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=YCZe
-----END PGP SIGNATURE-----
Merge tag 'nfs-rdma-for-3.20' of git://git.linux-nfs.org/projects/anna/nfs-rdma
NFS: Client side changes for RDMA
These patches improve the scalability of the NFSoRDMA client and take large
variables off of the stack. Additionally, the GFP_* flags are updated to
match what TCP uses.
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
* tag 'nfs-rdma-for-3.20' of git://git.linux-nfs.org/projects/anna/nfs-rdma: (21 commits)
xprtrdma: Update the GFP flags used in xprt_rdma_allocate()
xprtrdma: Clean up after adding regbuf management
xprtrdma: Allocate zero pad separately from rpcrdma_buffer
xprtrdma: Allocate RPC/RDMA receive buffer separately from struct rpcrdma_rep
xprtrdma: Allocate RPC/RDMA send buffer separately from struct rpcrdma_req
xprtrdma: Allocate RPC send buffer separately from struct rpcrdma_req
xprtrdma: Add struct rpcrdma_regbuf and helpers
xprtrdma: Refactor rpcrdma_buffer_create() and rpcrdma_buffer_destroy()
xprtrdma: Simplify synopsis of rpcrdma_buffer_create()
xprtrdma: Take struct ib_qp_attr and ib_qp_init_attr off the stack
xprtrdma: Take struct ib_device_attr off the stack
xprtrdma: Free the pd if ib_query_qp() fails
xprtrdma: Remove rpcrdma_ep::rep_func and ::rep_xprt
xprtrdma: Move credit update to RPC reply handler
xprtrdma: Remove rl_mr field, and the mr_chunk union
xprtrdma: Remove rpcrdma_ep::rep_ia
xprtrdma: Rename "xprt" and "rdma_connect" fields in struct rpcrdma_xprt
xprtrdma: Clean up hdrlen
xprtrdma: Display XIDs in host byte order
xprtrdma: Modernize htonl and ntohl
...
This is yet another Broadcom bluetooth chip with ACPI ID BCM2E40.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The bnep_get_device function may be triggered by an ioctl just after a
connection has gone down. In such a case the respective L2CAP chan->conn
pointer will get set to NULL (by l2cap_chan_del). This patch adds a
missing NULL check for this case in the bnep_get_device() function.
Reported-by: Patrik Flykt <patrik.flykt@linux.intel.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS fixes for net
The following patchset contains Netfilter/IPVS fixes for your net tree,
they are:
1) Validate hooks for nf_tables NAT expressions, otherwise users can
crash the kernel when using them from the wrong hook. We already
got one user trapped on this when configuring masquerading.
2) Fix a BUG splat in nf_tables with CONFIG_DEBUG_PREEMPT=y. Reported
by Andreas Schultz.
3) Avoid unnecessary reroute of traffic in the local input path
in IPVS that triggers a crash in in xfrm. Reported by Florian
Wiessner and fixes by Julian Anastasov.
4) Fix memory and module refcount leak from the error path of
nf_tables_newchain().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The kfree() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-By: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currntly, if we are not doing UFO on the packet, all UDP
packets will start with CHECKSUM_NONE and thus perform full
checksum computations in software even if device support
IPv6 checksum offloading.
Let's start start with CHECKSUM_PARTIAL if the device
supports it and we are sending only a single packet at
or below mtu size.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit adds the same functionaliy to IPv6 that
commit 903ab86d19
Author: Herbert Xu <herbert@gondor.apana.org.au>
Date: Tue Mar 1 02:36:48 2011 +0000
udp: Add lockless transmit path
added to IPv4.
UDP transmit path can now run without a socket lock,
thus allowing multiple threads to send to a single socket
more efficiently.
This is only used when corking/MSG_MORE is not used.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we can individually construct IPv6 skbs to send, add a
udpv6_send_skb() function to populate the udp header and send the
skb. This allows udp_v6_push_pending_frames() to re-use this
function as well as enables us to add lockless sendmsg() support.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit is very similar to
commit 1c32c5ad6f
Author: Herbert Xu <herbert@gondor.apana.org.au>
Date: Tue Mar 1 02:36:47 2011 +0000
inet: Add ip_make_skb and ip_finish_skb
It adds IPv6 version of the helpers ip6_make_skb and ip6_finish_skb.
The job of ip6_make_skb is to collect messages into an ipv6 packet
and poplulate ipv6 eader. The job of ip6_finish_skb is to transmit
the generated skb. Together they replicated the job of
ip6_push_pending_frames() while also provide the capability to be
called independently. This will be needed to add lockless UDP sendmsg
support.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the ability to append data to arbitrary queue. This
will be needed later to implement lockless UDP sends.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull IPv6 cork initialization into its own function that
can be re-used. IPv6 specific cork data did not have an
explicit data structure. This patch creats eone so that
just ipv6 cork data can be as arguemts. Also, since
IPv6 tries to save the flow label into inet_cork_full
tructure, pass the full cork.
Adjust ip6_cork_release() to take cork data structures.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One deployment requirement of DCTCP is to be able to run
in a DC setting along with TCP traffic. As Glenn Judd's
NSDI'15 paper "Attaining the Promise and Avoiding the Pitfalls
of TCP in the Datacenter" [1] (tba) explains, one way to
solve this on switch side is to split DCTCP and TCP traffic
in two queues per switch port based on the DSCP: one queue
soley intended for DCTCP traffic and one for non-DCTCP traffic.
For the DCTCP queue, there's the marking threshold K as
explained in commit e3118e8359 ("net: tcp: add DCTCP congestion
control algorithm") for RED marking ECT(0) packets with CE.
For the non-DCTCP queue, there's f.e. a classic tail drop queue.
As already explained in e3118e8359, running DCTCP at scale
when not marking SYN/SYN-ACK packets with ECT(0) has severe
consequences as for non-ECT(0) packets, traversing the RED
marking DCTCP queue will result in a severe reduction of
connection probability.
This is due to the DCTCP queue being dominated by ECT(0) traffic
and switches handle non-ECT traffic in the RED marking queue
after passing K as drops, where K is usually a low watermark
in order to leave enough tailroom for bursts. Splitting DCTCP
traffic among several queues (ECN and non-ECN queue) is being
considered a terrible idea in the network community as it
splits single flows across multiple network paths.
Therefore, commit e3118e8359 implements this on Linux as
ECT(0) marked traffic, as we argue that marking all packets
of a DCTCP flow is the only viable solution and also doesn't
speak against the draft.
However, recently, a DCTCP implementation for FreeBSD hit also
their mainline kernel [2]. In order to let them play well
together with Linux' DCTCP, we would need to loosen the
requirement that ECT(0) has to be asserted during the 3WHS as
not implemented in FreeBSD. This simplifies the ECN test and
lets DCTCP work together with FreeBSD.
Joint work with Daniel Borkmann.
[1] https://www.usenix.org/conference/nsdi15/technical-sessions/presentation/judd
[2] 8ad8794452
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Glenn Judd <glenn.judd@morganstanley.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tx timestamps are looped onto the error queue on top of an skb. This
mechanism leaks packet headers to processes unless the no-payload
options SOF_TIMESTAMPING_OPT_TSONLY is set.
Add a sysctl that optionally drops looped timestamp with data. This
only affects processes without CAP_NET_RAW.
The policy is checked when timestamps are generated in the stack.
It is possible for timestamps with data to be reported after the
sysctl is set, if these were queued internally earlier.
No vulnerability is immediately known that exploits knowledge
gleaned from packet headers, but it may still be preferable to allow
administrators to lock down this path at the cost of possible
breakage of legacy applications.
Signed-off-by: Willem de Bruijn <willemb@google.com>
----
Changes
(v1 -> v2)
- test socket CAP_NET_RAW instead of capable(CAP_NET_RAW)
(rfc -> v1)
- document the sysctl in Documentation/sysctl/net.txt
- fix access control race: read .._OPT_TSONLY only once,
use same value for permission check and skb generation.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add timestamping option SOF_TIMESTAMPING_OPT_TSONLY. For transmit
timestamps, this loops timestamps on top of empty packets.
Doing so reduces the pressure on SO_RCVBUF. Payload inspection and
cmsg reception (aside from timestamps) are no longer possible. This
works together with a follow on patch that allows administrators to
only allow tx timestamping if it does not loop payload or metadata.
Signed-off-by: Willem de Bruijn <willemb@google.com>
----
Changes (rfc -> v1)
- add documentation
- remove unnecessary skb->len test (thanks to Richard Cochran)
Signed-off-by: David S. Miller <davem@davemloft.net>
When receiving an interface activation notification, if
the RF interface is NCI_RF_INTERFACE_NFCEE_DIRECT, we
need to ignore the following parameters and change the NCI
state machine to NCI_LISTEN_ACTIVE. According to the NCI
specification, the parameters should be 0 and shall be
ignored.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The NFCC sends an NCI_OP_RF_NFCEE_ACTION_NTF notification
to the host (DH) to let it know that for example an RF
transaction with a payment reader is done.
For now the notification handler is empty.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
NFC_EVT_TRANSACTION is sent through netlink in order for a
specific application running on a secure element to notify
userspace of an event. Typically the secure element application
counterpart on the host could interpret that event and act
upon it.
Forwarded information contains:
- SE host generating the event
- Application IDentifier doing the operation
- Applications parameters
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
According to the NCI specification, one can use HCI over NCI
to talk with specific NFCEE. The HCI network is viewed as one
logical NFCEE.
This is needed to support secure element running HCI only
firmwares embedded on an NCI capable chipset, like e.g. the
st21nfcb.
There is some duplication between this piece of code and the
HCI core code, but the latter would need to be abstracted even
more to be able to use NCI as a logical transport for HCP packets.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In order to communicate with an NFCEE, we need to open a logical
connection to it, by sending the NCI_OP_CORE_CONN_CREATE_CMD
command to the NFCC. It's left up to the drivers to decide when
to close an already opened logical connection.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
NFCEEs can be enabled or disabled by sending the
NCI_OP_NFCEE_MODE_SET_CMD command to the NFCC. This patch
provides an API for drivers to enable and disable e.g. their
NCI discoveredd secure elements.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
NFCEEs (NFC Execution Environment) have to be explicitly
discovered by sending the NCI_OP_NFCEE_DISCOVER_CMD
command. The NFCC will respond to this command by telling
us how many NFCEEs are connected to it. Then the NFCC sends
a notification command for each and every NFCEE connected.
Here we implement support for sending
NCI_OP_NFCEE_DISCOVER_CMD command, receiving the response
and the potential notifications.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The current NCI core only support the RF static connection.
For other NFC features such as Secure Element communication, we
may need to create logical connections to the NFCEE (Execution
Environment.
In order to track each logical connection ID dynamically, we add a
linked list of connection info pointers to the nci_dev structure.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This extended return parameters struct conflicts with the new Read Local
OOB Extended Data command definition. To avoid the conflict simply
rename the old "extended" version to the normal one and update the code
appropriately to take into account the two possible response PDU sizes.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When using LE_SCAN_FILTER_DUP_ENABLE, some controllers would send
advertising report from each LE device only once. That means that we
don't get any updates on RSSI value, and makes Service Discovery very
slow. This patch adds restarting scan when in Service Discovery, and
device with filtered uuid is found, but it's not in RSSI range to send
event yet. This way if device moves into range, we will quickly get RSSI
update.
Signed-off-by: Jakub Pawlowski <jpawlowski@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Currently there is no way to restart le scan, and it's needed in
service scan method. The way it work: it disable, and then enable le
scan on controller.
During the restart, we must remember when the scan was started, and
it's duration, to later re-schedule the le_scan_disable work, that was
stopped during the stop scan phase.
Signed-off-by: Jakub Pawlowski <jpawlowski@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds support to set/del bridge port attributes in hardware from
the bridge driver.
With this, when the user sends a bridge setlink message with no flags or
master flags set,
- the bridge driver ndo_bridge_setlink handler sets settings in the kernel
- calls the swicthdev api to propagate the attrs to the switchdev
hardware
You can still use the self flag to go to the switch hw or switch port
driver directly.
With this, it also makes sure a notification goes out only after the
attributes are set both in the kernel and hw.
The patch calls switchdev api only if BRIDGE_FLAGS_SELF is not set.
This is because the offload cases with BRIDGE_FLAGS_SELF are handled in
the caller (in rtnetlink.c).
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds two new api's netdev_switch_port_bridge_setlink
and netdev_switch_port_bridge_dellink to offload bridge port attributes
to switch port
(The names of the apis look odd with 'switch_port_bridge',
but am more inclined to change the prefix of the api to something else.
Will take any suggestions).
The api's look at the NETIF_F_HW_SWITCH_OFFLOAD feature flag to
pass bridge port attributes to the port device.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bridge flags are needed inside ndo_bridge_setlink/dellink handlers to
avoid another call to parse IFLA_AF_SPEC inside these handlers
This is used later in this series
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit be9f4a44e7 ("ipv4: tcp: remove per net tcp_sock")
I tried to address contention on a socket lock, but the solution
I chose was horrible :
commit 3a7c384ffd ("ipv4: tcp: unicast_sock should not land outside
of TCP stack") addressed a selinux regression.
commit 0980e56e50 ("ipv4: tcp: set unicast_sock uc_ttl to -1")
took care of another regression.
commit b5ec8eeac4 ("ipv4: fix ip_send_skb()") fixed another regression.
commit 811230cd85 ("tcp: ipv4: initialize unicast_sock sk_pacing_rate")
was another shot in the dark.
Really, just use a proper socket per cpu, and remove the skb_orphan()
call, to re-enable flow control.
This solves a serious problem with FQ packet scheduler when used in
hostile environments, as we do not want to allocate a flow structure
for every RST packet sent in response to a spoofed packet.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using Secure Connections Only mode, then only P-256 OOB data is
valid and should be provided. In case userspace provides P-192 and P-256
OOB data, then the P-192 values will be set to zero. However the present
value of the IO capability exchange still mentioned that both values
would be available. Fix this by telling the controller clearly that only
the P-256 OOB data is present.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
For debugging purposes it is good to know which OOB data is actually
currently loaded for each controller. So expose that list via debugfs.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When the Hardware Error event is send by the controller, the Bluetooth
core stores the error code. Expose it via debugfs so it can be retrieved
later on.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
To allow easier debugging when debug keys are generated, provide debugfs
entry for checking the setting of debug keys usage.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When the HCI Write Simple Pairing Debug Mode command has been issued,
the result needs to be tracked and stored. The hdev->ssp_debug_mode
variable is already present, but was never updated when the mode in
the controller was actually changed.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The value of the ssp_debug_mode should be accessible via debugfs to be
able to determine if a BR/EDR controller generates debugs keys or not.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Get rid of nr_cpu_ids and use modern percpu allocation.
Note that the sockets themselves are not yet allocated
using NUMA affinity.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current behavior only passes RTTs from sequentially acked data to CC.
If sender gets a combined ACK for segment 1 and SACK for segment 3, then the
computed RTT for CC is the time between sending segment 1 and receiving SACK
for segment 3.
Pass the minimum computed RTT from any acked data to CC, i.e. time between
sending segment 3 and receiving SACK for segment 3.
Signed-off-by: Kenneth Klette Jonassen <kennetkl@ifi.uio.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case the remote only provided P-192 or P-256 data for OOB pairing,
then make sure that the data value pointers are correctly set. That way
the core can provide correct information when remote OOB data present
information have to be communicated.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Before setting the OOB data present flag with SMP pairing, check the
newly introduced present tracking that actual OOB data values have
been provided. The existence of remote OOB data structure does not
actually mean that the correct data values are available.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When BR/EDR Secure Connections has been enabled, the OOB data present
value can take 2 additional values. The host has to clearly provide
details about if P-192 OOB data, P-256 OOB data or a combination of
P-192 and P-256 OOB data is present.
In case BR/EDR Secure Connections is not enabled or not supported,
then check that P-192 OOB data is actually present and return the
correct value based on that.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Instead of doing complex calculation every time the OOB data is used,
just calculate the OOB data present value and store it with the OOB
data raw values.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This is only an API consolidation and should make things more readable
it replaces var * HZ / 1000 constructs by msecs_to_jiffies(var).
Signed-off-by: Nicholas Mc Guire <der.herr@hofr.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
vlan_get_protocol() could not get network protocol if a skb has a 802.1ad
vlan tag or multiple vlans, which caused incorrect checksum calculation
in several drivers.
Fix vlan_get_protocol() to retrieve network protocol instead of incorrect
vlan protocol.
As the logic is the same as skb_network_protocol(), create a common helper
function __vlan_get_protocol() and call it from existing functions.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
They are all either written once or extremly rarely (e.g. from init
code), so we can move them to the .data..read_mostly section.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When making use of RFC5061, section 4.2.4. for setting the primary IP
address, we're passing a wrong parameter header to param_type2af(),
resulting always in NULL being returned.
At this point, param.p points to a sctp_addip_param struct, containing
a sctp_paramhdr (type = 0xc004, length = var), and crr_id as a correlation
id. Followed by that, as also presented in RFC5061 section 4.2.4., comes
the actual sctp_addr_param, which also contains a sctp_paramhdr, but
this time with the correct type SCTP_PARAM_IPV{4,6}_ADDRESS that
param_type2af() can make use of. Since we already hold a pointer to
addr_param from previous line, just reuse it for param_type2af().
Fixes: d6de309759 ("[SCTP]: Add the handling of "Set Primary IP Address" parameter to INIT")
Signed-off-by: Saran Maruti Ramanara <saran.neti@telus.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The subscription bitmask passed via struct sockaddr_nl is converted to
the group number when calling the netlink_bind() and netlink_unbind()
callbacks.
The conversion is however incorrect since bitmask (1 << 0) needs to be
mapped to group number 1. Note that you cannot specify the group number 0
(usually known as _NONE) from setsockopt() using NETLINK_ADD_MEMBERSHIP
since this is rejected through -EINVAL.
This problem became noticeable since 97840cb ("netfilter: nfnetlink:
fix insufficient validation in nfnetlink_bind") when binding to bitmask
(1 << 0) in ctnetlink.
Reported-by: Andre Tomt <andre@tomt.net>
Reported-by: Ivan Delalande <colona@arista.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch extends nft_compat to support ebtables extensions.
ebtables verdict codes are translated to the ones used by the nf_tables engine,
so we can properly use ebtables target extensions from nft_compat.
This patch extends previous work by Giuseppe Longo <giuseppelng@gmail.com>.
Signed-off-by: Arturo Borrero Gonzalez <arturo.borrero.glez@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Reflect the more conservative approach used in the socket transport's
version of this transport method. An RPC buffer allocation should
avoid forcing not just FS activity, but any I/O.
In particular, two recent changes missed updating xprtrdma:
- Commit c6c8fe79a8 ("net, sunrpc: suppress allocation warning ...")
- Commit a564b8f039 ("nfs: enable swap on NFS")
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
rpcrdma_{de}register_internal() are used only in verbs.c now.
MAX_RPCRDMAHDR is no longer used and can be removed.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Use the new rpcrdma_alloc_regbuf() API to shrink the amount of
contiguous memory needed for a buffer pool by moving the zero
pad buffer into a regbuf.
This is for consistency with the other uses of internally
registered memory.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
The rr_base field is currently the buffer where RPC replies land.
An RPC/RDMA reply header lands in this buffer. In some cases an RPC
reply header also lands in this buffer, just after the RPC/RDMA
header.
The inline threshold is an agreed-on size limit for RDMA SEND
operations that pass from server and client. The sum of the
RPC/RDMA reply header size and the RPC reply header size must be
less than this threshold.
The largest RDMA RECV that the client should have to handle is the
size of the inline threshold. The receive buffer should thus be the
size of the inline threshold, and not related to RPCRDMA_MAX_SEGS.
RPC replies received via RDMA WRITE (long replies) are caught in
rq_rcv_buf, which is the second half of the RPC send buffer. Ie,
such replies are not involved in any way with rr_base.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
The rl_base field is currently the buffer where each RPC/RDMA call
header is built.
The inline threshold is an agreed-on size limit to for RDMA SEND
operations that pass between client and server. The sum of the
RPC/RDMA header size and the RPC header size must be less than or
equal to this threshold.
Increasing the r/wsize maximum will require MAX_SEGS to grow
significantly, but the inline threshold size won't change (both
sides agree on it). The server's inline threshold doesn't change.
Since an RPC/RDMA header can never be larger than the inline
threshold, make all RPC/RDMA header buffers the size of the
inline threshold.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Because internal memory registration is an expensive and synchronous
operation, xprtrdma pre-registers send and receive buffers at mount
time, and then re-uses them for each RPC.
A "hardway" allocation is a memory allocation and registration that
replaces a send buffer during the processing of an RPC. Hardway must
be done if the RPC send buffer is too small to accommodate an RPC's
call and reply headers.
For xprtrdma, each RPC send buffer is currently part of struct
rpcrdma_req so that xprt_rdma_free(), which is passed nothing but
the address of an RPC send buffer, can find its matching struct
rpcrdma_req and rpcrdma_rep quickly via container_of / offsetof.
That means that hardway currently has to replace a whole rpcrmda_req
when it replaces an RPC send buffer. This is often a fairly hefty
chunk of contiguous memory due to the size of the rl_segments array
and the fact that both the send and receive buffers are part of
struct rpcrdma_req.
Some obscure re-use of fields in rpcrdma_req is done so that
xprt_rdma_free() can detect replaced rpcrdma_req structs, and
restore the original.
This commit breaks apart the RPC send buffer and struct rpcrdma_req
so that increasing the size of the rl_segments array does not change
the alignment of each RPC send buffer. (Increasing rl_segments is
needed to bump up the maximum r/wsize for NFS/RDMA).
This change opens up some interesting possibilities for improving
the design of xprt_rdma_allocate().
xprt_rdma_allocate() is now the one place where RPC send buffers
are allocated or re-allocated, and they are now always left in place
by xprt_rdma_free().
A large re-allocation that includes both the rl_segments array and
the RPC send buffer is no longer needed. Send buffer re-allocation
becomes quite rare. Good send buffer alignment is guaranteed no
matter what the size of the rl_segments array is.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
There are several spots that allocate a buffer via kmalloc (usually
contiguously with another data structure) and then register that
buffer internally. I'd like to split the buffers out of these data
structures to allow the data structures to scale.
Start by adding functions that can kmalloc and register a buffer,
and can manage/preserve the buffer's associated ib_sge and ib_mr
fields.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Move the details of how to create and destroy rpcrdma_req and
rpcrdma_rep structures into helper functions.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Clean up: There is one call site for rpcrdma_buffer_create(). All of
the arguments there are fields of an rpcrdma_xprt.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Reduce stack footprint of the connection upcall handler function.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Device attributes are large, and are used in more than one place.
Stash a copy in dynamically allocated memory.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
If ib_query_qp() fails or the memory registration mode isn't
supported, don't leak the PD. An orphaned IB/core resource will
cause IB module removal to hang.
Fixes: bd7ed1d133 ("RPC/RDMA: check selected memory registration ...")
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Clean up: The rep_func field always refers to rpcrdma_conn_func().
rep_func should have been removed by commit b45ccfd25d ("xprtrdma:
Remove MEMWINDOWS registration modes").
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Reduce work in the receive CQ handler, which can be run at hardware
interrupt level, by moving the RPC/RDMA credit update logic to the
RPC reply handler.
This has some additional benefits: More header sanity checking is
done before trusting the incoming credit value, and the receive CQ
handler no longer touches the RPC/RDMA header (the CPU stalls while
waiting for the header contents to be brought into the cache).
This further extends work begun by commit e7ce710a88 ("xprtrdma:
Avoid deadlock when credit window is reset").
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Clean up: Since commit 0ac531c183 ("xprtrdma: Remove REGISTER
memory registration mode"), the rl_mr pointer is no longer used
anywhere.
After removal, there's only a single member of the mr_chunk union,
so mr_chunk can be removed as well, in favor of a single pointer
field.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Clean up: This field is not used.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Clean up: Use consistent field names in struct rpcrdma_xprt.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Clean up: Replace naked integers with a documenting macro.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
xprtsock.c and the backchannel code display XIDs in host byte order.
Follow suit in xprtrdma.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Clean up: Replace htonl and ntohl with the be32 equivalents.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Make it easier to grep the system log for specific error conditions.
The wc.opcode field is not included because opcode numbers are
sparse, and because wc.opcode is not necessarily valid when
completion reports an error.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
commit f5a41847ac ("ipvs: move ip_route_me_harder for ICMP")
from 2.6.37 introduced ip_route_me_harder() call for responses to
local clients, so that we can provide valid rt_src after SNAT.
It was used by TCP to provide valid daddr for ip_send_reply().
After commit 0a5ebb8000 ("ipv4: Pass explicit daddr arg to
ip_send_reply()." from 3.0 this rerouting is not needed anymore
and should be avoided, especially in LOCAL_IN.
Fixes 3.12.33 crash in xfrm reported by Florian Wiessner:
"3.12.33 - BUG xfrm_selector_match+0x25/0x2f6"
Reported-by: Smart Weblications GmbH - Florian Wiessner <f.wiessner@smart-weblications.de>
Tested-by: Smart Weblications GmbH - Florian Wiessner <f.wiessner@smart-weblications.de>
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
RFC 1191 said, "a host MUST not increase its estimate of the Path
MTU in response to the contents of a Datagram Too Big message."
Signed-off-by: Li Wei <lw@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When many pf_packet listeners are created on a lot of interfaces the
current implementation using global packet type lists scales poorly.
This patch adds per net_device packet type lists to fix this problem.
The patch was originally written by Eric Biederman for linux-2.6.29.
Tested on linux-3.16.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Salam Noureddine <noureddine@arista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When IFLA_LINK_NETNSID is used, the netdevice should be built in this link netns
and moved at the end to another netns (pointed by the socket netns or
IFLA_NET_NS_[PID|FD]).
Existing user of the newlink handler will use the netns argument (src_net) to
find a link netdevice or to check some other information into the link netns.
For example, to find a netdevice, two information are required: an ifindex
(usually from IFLA_LINK) and a netns (this link netns).
Note: when using IFLA_LINK_NETNSID and IFLA_NET_NS_[PID|FD], a user may create a
netdevice that stands in netnsX and with its link part in netnsY, by sending a
rtnl message from netnsZ.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
src_net points to the netns where the netlink message has been received. This
netns may be different from the netns where the interface is created (because
the user may add IFLA_NET_NS_[PID|FD]). In this case, src_net is the link netns.
It seems wrong to override the netns in the newlink() handler because if it
was not already src_net, it means that the user explicitly asks to create the
netdevice in another netns.
CC: Sjur Brændeland <sjur.brandeland@stericsson.com>
CC: Dmitry Tarnyagin <dmitry.tarnyagin@lockless.no>
Fixes: 8391c4aab1 ("caif: Bugfixes in CAIF netdevice for close and flow control")
Fixes: c412540063 ("caif-hsi: Add rtnl support")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When I added sk_pacing_rate field, I forgot to initialize its value
in the per cpu unicast_sock used in ip_send_unicast_reply()
This means that for sch_fq users, RST packets, or ACK packets sent
on behalf of TIME_WAIT sockets might be sent to slowly or even dropped
once we reach the per flow limit.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes: 95bd09eb27 ("tcp: TSO packets automatic sizing")
Signed-off-by: David S. Miller <davem@davemloft.net>
TIME_WAIT sockets are not owning any skb.
ip_send_unicast_reply() and tcp_v6_send_response() both use
regular sockets.
We can safely remove a test in sch_fq and save one cache line miss,
as sk_state is far away from sk_pacing_rate.
Tested at Google for about one year.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NET_ACT_CONNMARK fails to build if NF_CONNTRACK_MARK is disabled,
and d7924450e1 ("act_connmark: Add missing dependency on
NF_CONNTRACK_MARK") fixed that case, but missed the cased where
NF_CONNTRACK is a loadable module.
This adds the second dependency to ensure that NET_ACT_CONNMARK
can only be built-in if NF_CONNTRACK is also part of the kernel
rather than a loadable module.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
