pm8001_phy_control PHY_FUNC_HARD_RESET locks up on second try via
smp_phy_control because response HW_EVENT_PHY_START_STATUS fails to complete
previous command. The PM8001F_RUN_TIME flag is not treated as a bit, but a
state in all readers, yet once we are operational or in the run time state,
the flags use a bit-set operation.
Signed-off-by: Mark Salyzyn <mark_salyzyn@xyratex.com>
Acked-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This implements basic power management for SCSI tapes.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Acked-by: Kai Mäkisara <kai.makisara@kolumbus.fi>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch (as1520) fixes a bug in the SCSI layer's power management
implementation.
LUN scanning can be carried out asynchronously in do_scan_async(), and
sd uses an asynchronous thread for the time-consuming parts of disk
probing in sd_probe_async(). Currently nothing coordinates these
async threads with system sleep transitions; they can and do attempt
to continue scanning/probing SCSI devices even after the host adapter
has been suspended. As one might expect, the outcome is not ideal.
This is what the "prepare" stage of system suspend was created for.
After the prepare callback has been called for a host, target, or
device, drivers are not allowed to register any children underneath
them. Currently the SCSI prepare callback is not implemented; this
patch rectifies that omission.
For SCSI hosts, the prepare routine calls scsi_complete_async_scans()
to wait until async scanning is finished. It might be slightly more
efficient to wait only until the host in question has been scanned,
but there's currently no way to do that. Besides, during a sleep
transition we will ultimately have to wait until all the host scanning
has finished anyway.
For SCSI devices, the prepare routine calls async_synchronize_full()
to wait until sd probing is finished. The routine does nothing for
SCSI targets, because asynchronous target scanning is done only as
part of host scanning.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@kernel.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
In do_scan_async(), calling scsi_autopm_put_host(shost) may reference
freed shost, and cause Posison overwitten warning.
Yes, this case can happen, for example, an USB is disconnected just
when do_scan_async() thread starts to run, then scsi_host_put() called
in scsi_finish_async_scan() will lead to shost be freed(because the
refcount of shost->shost_gendev decreases to 1 after USB disconnects),
at this point, if references shost again, system will show following
warning msg.
To make scsi_autopm_put_host(shost) always reference a valid shost,
put it just before scsi_host_put() in function
scsi_finish_async_scan().
[ 299.281565] =============================================================================
[ 299.281634] BUG kmalloc-4096 (Tainted: G I ): Poison overwritten
[ 299.281682] -----------------------------------------------------------------------------
[ 299.281684]
[ 299.281752] INFO: 0xffff880056c305d0-0xffff880056c305d0. First byte
0x6a instead of 0x6b
[ 299.281816] INFO: Allocated in scsi_host_alloc+0x4a/0x490 age=1688
cpu=1 pid=2004
[ 299.281870] __slab_alloc+0x617/0x6c1
[ 299.281901] __kmalloc+0x28c/0x2e0
[ 299.281931] scsi_host_alloc+0x4a/0x490
[ 299.281966] usb_stor_probe1+0x5b/0xc40 [usb_storage]
[ 299.282010] storage_probe+0xa4/0xe0 [usb_storage]
[ 299.282062] usb_probe_interface+0x172/0x330 [usbcore]
[ 299.282105] driver_probe_device+0x257/0x3b0
[ 299.282138] __driver_attach+0x103/0x110
[ 299.282171] bus_for_each_dev+0x8e/0xe0
[ 299.282201] driver_attach+0x26/0x30
[ 299.282230] bus_add_driver+0x1c4/0x430
[ 299.282260] driver_register+0xb6/0x230
[ 299.282298] usb_register_driver+0xe5/0x270 [usbcore]
[ 299.282337] 0xffffffffa04ab03d
[ 299.282364] do_one_initcall+0x47/0x230
[ 299.282396] sys_init_module+0xa0f/0x1fe0
[ 299.282429] INFO: Freed in scsi_host_dev_release+0x18a/0x1d0 age=85
cpu=0 pid=2008
[ 299.282482] __slab_free+0x3c/0x2a1
[ 299.282510] kfree+0x296/0x310
[ 299.282536] scsi_host_dev_release+0x18a/0x1d0
[ 299.282574] device_release+0x74/0x100
[ 299.282606] kobject_release+0xc7/0x2a0
[ 299.282637] kobject_put+0x54/0xa0
[ 299.282668] put_device+0x27/0x40
[ 299.282694] scsi_host_put+0x1d/0x30
[ 299.282723] do_scan_async+0x1fc/0x2b0
[ 299.282753] kthread+0xdf/0xf0
[ 299.282782] kernel_thread_helper+0x4/0x10
[ 299.282817] INFO: Slab 0xffffea00015b0c00 objects=7 used=7 fp=0x
(null) flags=0x100000000004080
[ 299.282882] INFO: Object 0xffff880056c30000 @offset=0 fp=0x (null)
[ 299.282884]
...
Signed-off-by: Huajun Li <huajun.li.lee@gmail.com>
Cc: stable@kernel.org
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
With IOs running and PegHalt testing the system reboots when memory reset is
performed during device initialization.
Signed-off-by: Shyam Sundar <shyam.sundar@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Complete the mailbox command timed out before initiating another abort cycle
to recover so that mailbox commands issued during next reset cycle don't fail
due to pending mailbox access timeout.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Remove the check for a NULL fcport so that the host reset will run
unconditionally to unwedge any commands before the device is offlined and to
prevent a quick runthrough of the SCSI error handling.
Signed-off-by: Michael Christie <mchristi@redhat.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
ISP2200 adapters only have 24 mailbox registers so read only that many.
Reported-by: Olatunji Ruwase <oor@cs.cmu.edu>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This can cause instability in mailbox command state machine handling.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Not clearing the options flags in mbx1 could lead the firmware
into interpreting old data in mbx1 through mbx8. This could
lead to inadvertent DMA read/write operations to stale memory.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Many locations within the driver would use an inconsistent set of
checks to determine ISP-reset state. Consolidate the checks into
this inline-helper.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
NULL orom ptr passed in for verification which caused page fault.
We will set a default version when we don't have orom struct.
Reported-by: Dan Melnic <dan@seamicro.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
In some scenarios, an EEH error can take a long time to be detected, since the
driver issues an MMIO read only after a device reset command times out and we
try to reset the adapter. This patch adds some code in ipr_cancel_op() to read
a hardware register so we detect the error earlier in case the op is being
aborted because of a timeout caused by a frozen adapter slot.
Another problem in such scenarios is that in __ipr_eh_host_reset() we change the
dump state flag from WAIT_FOR_DUMP to GET_DUMP, and the flag is later changed
from GET_DUMP to READ_DUMP in ipr_reset_restore_cfg_space(). However, if when
__ipr_eh_host_reset() is called by the SCSI error handling the function
ipr_reset_restore_cfg_space() has already been called by the PCI EEH code, we
end up with the flag in an inconsistent state. This patch also prevents this
problem.
Signed-off-by: Kleber Sacilotto de Souza <klebers@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If ioc->pci_error_recovery is set, goto out in mpt2sas_base_hard_reset_handler()
leads to unlock unheld ioc->reset_in_progress_mutex.
The patch fixes the issue by jumping afer mutex_unlock() call.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: "Nandigama, Nagalakshmi" <Nagalakshmi.Nandigama@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Says Jens:
"Time to push off some of the pending items. I really wanted to wait
until we had the regression nailed, but alas it's not quite there yet.
But I'm very confident that it's "just" a missing expire on exit, so
fix from Tejun should be fairly trivial. I'm headed out for a week on
the slopes.
- Killing the barrier part of mtip32xx. It doesn't really support
barriers, and it doesn't need them (writes are fully ordered).
- A few fixes from Dan Carpenter, preventing overflows of integer
multiplication.
- A fixup for loop, fixing a previous commit that didn't quite solve
the partial read problem from Dave Young.
- A bio integer overflow fix from Kent Overstreet.
- Improvement/fix of the door "keep locked" part of the cdrom shared
code from Paolo Benzini.
- A few cfq fixes from Shaohua Li.
- A fix for bsg sysfs warning when removing a file it did not create
from Stanislaw Gruszka.
- Two fixes for floppy from Vivek, preventing a crash.
- A few block core fixes from Tejun. One killing the over-optimized
ioc exit path, cleaning that up nicely. Two others fixing an oops
on elevator switch, due to calling into the scheduler merge check
code without holding the queue lock."
* 'for-linus' of git://git.kernel.dk/linux-block:
block: fix lockdep warning on io_context release put_io_context()
relay: prevent integer overflow in relay_open()
loop: zero fill bio instead of return -EIO for partial read
bio: don't overflow in bio_get_nr_vecs()
floppy: Fix a crash during rmmod
floppy: Cleanup disk->queue before caling put_disk() if add_disk() was never called
cdrom: move shared static to cdrom_device_info
bsg: fix sysfs link remove warning
block: don't call elevator callbacks for plug merges
block: separate out blk_rq_merge_ok() and blk_try_merge() from elevator functions
mtip32xx: removed the irrelevant argument of mtip_hw_submit_io() and the unused member of struct driver_data
block: strip out locking optimization in put_io_context()
cdrom: use copy_to_user() without the underscores
block: fix ioc locking warning
block: fix NULL icq_cache reference
block,cfq: change code order
11a3122f6c "block: strip out locking optimization in put_io_context()"
removed ioc_lock depth lockdep annoation along with locking
optimization; however, while recursing from put_io_context() is no
longer possible, ioc_release_fn() may still end up putting the last
reference of another ioc through elevator, which wlil grab ioc->lock
triggering spurious (as the ioc is always different one) A-A deadlock
warning.
As this can only happen one time from ioc_release_fn(), using non-zero
subclass from ioc_release_fn() is enough. Use subclass 1.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Quoth David:
1) GRO MAC header comparisons were ethernet specific, breaking other
link types. This required a multi-faceted fix to cure the originally
noted case (Infiniband), because IPoIB was lying about it's actual
hard header length. Thanks to Eric Dumazet, Roland Dreier, and
others.
2) Fix build failure when INET_UDP_DIAG is built in and ipv6 is modular.
From Anisse Astier.
3) Off by ones and other bug fixes in netprio_cgroup from Neil Horman.
4) ipv4 TCP reset generation needs to respect any network interface
binding from the socket, otherwise route lookups might give a
different result than all the other segments received. From Shawn
Lu.
5) Fix unintended regression in ipv4 proxy ARP responses, from Thomas
Graf.
6) Fix SKB under-allocation bug in sh_eth, from Yoshihiro Shimoda.
7) Revert skge PCI mapping changes that are causing crashes for some
folks, from Stephen Hemminger.
8) IPV4 route lookups fill in the wildcarded fields of the given flow
lookup key passed in, which is fine most of the time as this is
exactly what the caller's want. However there are a few cases that
want to retain the original flow key values afterwards, so handle
those cases properly. Fix from Julian Anastasov.
9) IGB/IXGBE VF lookup bug fixes from Greg Rose.
10) Properly null terminate filename passed to ethtool flash device
method, from Ben Hutchings.
11) S3 resume fix in via-velocity from David Lv.
12) Fix double SKB free during xmit failure in CAIF, from Dmitry
Tarnyagin.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (72 commits)
net: Don't proxy arp respond if iif == rt->dst.dev if private VLAN is disabled
ipv4: Fix wrong order of ip_rt_get_source() and update iph->daddr.
netprio_cgroup: fix wrong memory access when NETPRIO_CGROUP=m
netprio_cgroup: don't allocate prio table when a device is registered
netprio_cgroup: fix an off-by-one bug
bna: fix error handling of bnad_get_flash_partition_by_offset()
isdn: type bug in isdn_net_header()
net: Make qdisc_skb_cb upper size bound explicit.
ixgbe: ethtool: stats user buffer overrun
ixgbe: dcb: up2tc mapping lost on disable/enable CEE DCB state
ixgbe: do not update real num queues when netdev is going away
ixgbe: Fix broken dependency on MAX_SKB_FRAGS being related to page size
ixgbe: Fix case of Tx Hang in PF with 32 VFs
ixgbe: fix vf lookup
igb: fix vf lookup
e1000: add dropped DMA receive enable back in for WoL
gro: more generic L2 header check
IPoIB: Stop lying about hard_header_len and use skb->cb to stash LL addresses
zd1211rw: firmware needs duration_id set to zero for non-pspoll frames
net: enable TC35815 for MIPS again
...
Commit 653241 (net: RFC3069, private VLAN proxy arp support) changed
the behavior of arp proxy to send arp replies back out on the interface
the request came in even if the private VLAN feature is disabled.
Previously we checked rt->dst.dev != skb->dev for in scenarios, when
proxy arp is enabled on for the netdevice and also when individual proxy
neighbour entries have been added.
This patch adds the check back for the pneigh_lookup() scenario.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Jesper Dangaard Brouer <hawk@comx.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fix a bug which introduced by commit ac8a4810 (ipv4: Save
nexthop address of LSRR/SSRR option to IPCB.).In that patch, we saved
the nexthop of SRR in ip_option->nexthop and update iph->daddr until
we get to ip_forward_options(), but we need to update it before
ip_rt_get_source(), otherwise we may get a wrong src.
Signed-off-by: Li Wei <lw@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the netprio_cgroup module is not loaded, net_prio_subsys_id
is -1, and so sock_update_prioidx() accesses cgroup_subsys array
with negative index subsys[-1].
Make the code resembles cls_cgroup code, which is bug free.
Origionally-authored-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
So we delay the allocation till the priority is set through cgroup,
and this makes skb_update_priority() faster when it's not set.
This also eliminates an off-by-one bug similar with the one fixed
in the previous patch.
Origionally-authored-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
# mount -t cgroup xxx /mnt
# mkdir /mnt/tmp
# cat /mnt/tmp/net_prio.ifpriomap
lo 0
eth0 0
virbr0 0
# echo 'lo 999' > /mnt/tmp/net_prio.ifpriomap
# cat /mnt/tmp/net_prio.ifpriomap
lo 999
eth0 0
virbr0 4101267344
We got weired output, because we exceeded the boundary of the array.
We may even crash the kernel..
Origionally-authored-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/i915: fixup interlaced bits clearing in PIPECONF on PCH_SPLIT (v2)
drm/i915: no lvds quirk for AOpen MP45
drm/i915: Force explicit bpp selection for intel_dp_link_required
drm/radeon: do not continue after error from r600_ib_test
drivers/gpu/drm/drm_ioc32.c: initialize all fields
drm/i915: fixup interlaced bits clearing in PIPECONF on PCH_SPLIT
drm/i915:: Disable FBC on SandyBridge
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf: Fix double start/stop in x86_pmu_start()
perf evsel: Fix an issue where perf report fails to show the proper percentage
perf tools: Fix prefix matching for kernel maps
perf tools: Fix perf stack to non executable on x86_64
perf: Remove deprecated WARN_ON_ONCE()
* 'drm-intel-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/keithp/linux:
drm/i915: fixup interlaced bits clearing in PIPECONF on PCH_SPLIT (v2)
drm/i915: no lvds quirk for AOpen MP45
drm/i915: Force explicit bpp selection for intel_dp_link_required
drm/i915: fixup interlaced bits clearing in PIPECONF on PCH_SPLIT
drm/i915:: Disable FBC on SandyBridge
"subbuf_size" and "n_subbufs" come from the user and they need to be
capped to prevent an integer overflow.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Just a few new device ids, omap serial driver regression fixes, and a
build fix for the 8250 driver movement.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk80KZgACgkQMUfUDdst+yk0HgCeIdU3VTWqdxZDXp3G1sFIXZ1b
47YAnRAMAar+/aLaNhqGrcz7aa5y2cUU
=8sr8
-----END PGP SIGNATURE-----
Merge tag 'tty-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Serial/TTY fixes for the 3.3-rc3 tree
Just a few new device ids, omap serial driver regression fixes, and a
build fix for the 8250 driver movement.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* tag 'tty-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: serial: omap-serial: wakeup latency constraint is in microseconds, not milliseconds
tty: serial: OMAP: block idle while the UART is transferring data in PIO mode
tty: serial: OMAP: use a 1-byte RX FIFO threshold in PIO mode
m32r: relocate drivers back out of 8250 dir
tty: fix a build failure on sparc
serial: samsung: Add support for EXYNOS5250
serial: samsung: Add support for EXYNOS4212 and EXYNOS4412
drivers/tty/vt/vt_ioctl.c: fix KDFONTOP 32bit compatibility layer
Big things here is the deletion of the Android pmem driver, as it's
obsolete and no one uses it, the gma500 driver as it's already in the
drm portion of the kernel tree, and the pohmelfs filesystem as it's
obsolete and a rewritten version is being proposed for the fs/ section
of the kernel.
Other than that, a smattering of different bugfixes and regressions, and
some omap drm api merge fixups that were needed due to api changes in
the main portion of the drm tree, allowing this code to build properly
again.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk80KLYACgkQMUfUDdst+ykhiwCg2ctSu4umygA1ErAedAA+sJkv
psYAn20OZQDyuBcBAIzL2L+Y/BUz8bXt
=xvyx
-----END PGP SIGNATURE-----
Merge tag 'staging-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Staging tree patches for 3.3-rc3
Big things here is the deletion of the Android pmem driver, as it's
obsolete and no one uses it, the gma500 driver as it's already in the
drm portion of the kernel tree, and the pohmelfs filesystem as it's
obsolete and a rewritten version is being proposed for the fs/ section
of the kernel.
Other than that, a smattering of different bugfixes and regressions, and
some omap drm api merge fixups that were needed due to api changes in
the main portion of the drm tree, allowing this code to build properly
again.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* tag 'staging-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (28 commits)
staging: pohmelfs: remove drivers/staging/pohmelfs
staging: android/ram_console: Don't build on arches w/o ioremap
staging: r8712u: Use asynchronous firmware loading
staging: usbip: fix to prevent potentially using uninitialized spinlock
staging: r8712u: Fix problem when CONFIG_R8712_AP is set
staging: tidspbridge: fix incorrect free to drv_datap
staging: tidspbridge: fix bridge_open memory leaks
staging: android: lowmemorykiller: Don't wait more than one second for a process to die
MAINTAINERS: staging: iio: add iio information
staging: zcache: fix serialization bug in zv stats
staging: fix go7007-usb license
Staging: android: binder: Fix crashes when sharing a binder file between processes
Staging: android: Remove pmem driver
Staging: asus_oled: fix NULL-ptr crash on unloading
Staging: asus_oled: fix image processing
Staging: android: binder: Don't call dump_stack in binder_vma_open
staging: r8712u: Add new Sitecom UsB ID
zcache: Set SWIZ_BITS to 8 to reduce tmem bucket lock contention.
zcache: fix deadlock condition
staging: drm/omap: fix locking issue
...
A few fixes for kobject warnings that have popped up in the cpu hotplug path,
and a regression fix for the speed of the hotplug memory code.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk80J1cACgkQMUfUDdst+ylYfgCcClIeUw4njh3Tup9BpRrdBprr
fBsAoLKKhaZDsnma85PJRDAvtM2guoi7
=0TZ9
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Driver core fixes for the 3.3-rc3 tree.
A few fixes for kobject warnings that have popped up in the cpu hotplug path,
and a regression fix for the speed of the hotplug memory code.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* tag 'driver-core-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
driver-core: cpu: fix kobject warning when hotplugging a cpu
ACPI: remove duplicated lines of merging problems with acpi_processor_add
docbook: fix fatal errors in device-drivers docbook and add DMA Management section
drivers/base/memory.c: fix memory_dev_init() long delay
driver core: cpu: remove kernel warning when removing a cpu
Nothing big here, some Kconfig fixes for the MISC_DEVICES config option
that was being used incorrectly, and some other minor bug fixes.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk80HSAACgkQMUfUDdst+ymFsQCghwKbV9B9z5fgUXYwFQJ/pD2j
GhsAn3J2mhhHN/vtSPQAN9Vu59Xb/tCi
=VZaE
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Minor char-misc fixes for 3.3-rc3
Nothing big here, some Kconfig fixes for the MISC_DEVICES config option
that was being used incorrectly, and some other minor bug fixes.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* tag 'char-misc-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
mmc: cb710 core: Add missing spin_lock_init for irq_lock of struct cb710_chip
cs5535-mfgpt: don't call __init function from __devinit
vmw_balloon: fix for a -Wuninitialized warning
drivers: misc: Remove MISC_DEVICES config option
c2port: fix build error for duramar2150 due to missing header.
Here are a few minor USB fixes and a bunch of device id updates for the
USB drivers.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk80Ki4ACgkQMUfUDdst+ymp3wCfUG2LtQOC2qpzpnl1bcivSA18
11gAn09DbcldfH4k12HyCr7PuBnjILQh
=vfEv
-----END PGP SIGNATURE-----
Merge tag 'usb-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
USB fixes for 3.3-rc3
Here are a few minor USB fixes and a bunch of device id updates for the
USB drivers.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* tag 'usb-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: usbserial: add new PID number (0xa951) to the ftdi driver
usb: ch9.h: usb_endpoint_maxp() uses __le16_to_cpu()
usb: musb: fix a build error on mips
uwb & wusb & usb wireless controllers: fix kconfig error & build errors
usb: Skip PCI USB quirk handling for Netlogic XLP
powerpc/usb: fix issue of CPU halt when missing USB PHY clock
usb: otg: mv_otg: Add dependence
usb: host: Distinguish Kconfig text for Freescale controllers
USB: add new zte 3g-dongle's pid to option.c
usb: ch9.h: usb_endpoint_maxp() uses __le16_to_cpu()
USB: qcserial: don't enable autosuspend
USB: qcserial: add several new serial devices
usb: otg: mv_otg: Add dependence
usb: gadget: zero: fix bug in loopback autoresume handling
The current error handling doesn't work because we flash_part is a u32
so the checks for negative error codes don't work. I considered making
things signed but I don't know the hardware enough to say if that's a
problem. Really, we don't use the error codes so just returning zero
for all problems is fine.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We use len to store the return value from eth_header(). eth_header()
can return -ETH_HLEN (-14). We want to pass this back instead of
truncating it to 65522 and returning that.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Treat pwmX as a measured value, not as a (mostly static) limit value, so
that it is updated more frequently from the device register.
Signed-off-by: Nikolaus Schulz <mail@microschulz.de>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Just like skb->cb[], so that qdisc_skb_cb can be encapsulated inside
of other data structures.
This is intended to be used by IPoIB so that it can remember
addressing information stored at hard_header_ops->create() time that
it can fetch when the packet gets to the transmit routine.
Signed-off-by: David S. Miller <davem@davemloft.net>
The receive FIFO wakeup latency estimate in the omap-serial driver is
three orders of magnitude too small. This effectively prevents the
MPU from going to a low-power state when CONFIG_CPU_IDLE=y. This is a
major power management regression and masks some other FIFO-related
bugs in the driver.
Fix by correcting the most egregious problem in the RX wakeup latency
estimate. There are several other flaws in the estimator; these will
be fixed by a separate patch series intended for 3.4.
The difference in low-power states with this patch can be observed via
debugfs in pm_debug/count.
This estimate does not have any effect when CONFIG_CPU_IDLE=n.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Alan Cox <alan@linux.intel.com>
Acked-by: Govindraj.R <govindraj.raja@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prevent OMAP UARTs from going idle while they are still transferring
data in PIO mode. This works around an oversight in the OMAP UART
hardware present in OMAP34xx and earlier: an idle UART won't send a
wakeup when the TX FIFO threshold is reached. This causes long delays
during data transmission when the MPU powerdomain enters a low-power
mode. The MPU interrupt controller is not able to respond to
interrupts when it's in a low-power state, so the TX buffer is not
refilled until another wakeup event occurs.
This fix changes the erratum i291 DMA idle workaround. Rather than
toggling between force-idle and no-idle, it will toggle between
smart-idle and no-idle. The important part of the workaround is the
no-idle part, so this shouldn't result in any change in behavior.
This fix should work on all OMAP UARTs. Future patches intended for
the 3.4 merge window will make this workaround conditional on a
"feature" flag, and will use the OMAP36xx+ TX event wakeup support.
Thanks to Kevin Hilman <khilman@ti.com> for mentioning the erratum i291
workaround, which led to the development of this approach.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Govindraj.R <govindraj.raja@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the (default) PIO mode, use a one-byte RX FIFO threshold. The OMAP
UART IP blocks do not appear to be capable of waking the system under
an RX timeout condition. Since the previous RX FIFO threshold was 16
bytes, this meant that omap-serial.c did not become aware of any
received data until all those bytes arrived or until another UART
interrupt occurred. This made the serial console and presumably other
serial applications (GPS, serial Bluetooth) unusable or extremely
slow. A 1-byte RX FIFO threshold also allows the MPU to enter a
low-power consumption state while waiting for the FIFO to fill.
This can be verified using the serial console by comparing the
behavior when "0123456789abcde" is pasted in from another window, with
the behavior when "0123456789abcdef" is pasted in. Since the former
string is less than sixteen bytes long, the string is not echoed for
some time, while the latter string is echoed immediately.
DMA operation is unaffected by this patch.
Thanks to Russell King - ARM Linux <linux@arm.linux.org.uk> for some
additional information on the standard behavior of the RX timeout
event, which was used to improve this commit description.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Govindraj Raja <govindraj.r@ti.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Russell King <linux@arm.linux.org.uk>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
_parse_integer() does one or two division instructions (which are slow)
per digit parsed to perform the overflow check.
Furthermore, these are particularly expensive examples of division
instruction as the number of clock cycles required to complete them may
go up with the position of the most significant set bit in the dividend:
if (*res > div_u64(ULLONG_MAX - val, base))
which is as maximal as possible.
Worse, on 32-bit arches, more than one of these division instructions
may be required per digit.
So, assuming we don't support a base of more than 16, skip the check if the
top nibble of the result is not set at this point.
Signed-off-by: David Howells <dhowells@redhat.com>
[ Changed it to not dereference the pointer all the time - even if the
compiler can and does optimize it away, the code just looks cleaner.
And edited the top nybble test slightly to make the code generated on
x86-64 better in the loop - test against a hoisted constant instead of
shifting and testing the result ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If the number of tx/rx queues changes the ethtool ioctl
ETHTOOL_GSTATS may overrun the userspace buffer. This
occurs because the general practice in user space to
query stats is to issue a ETHTOOL_GSSET cmd to learn the
buffer size needed, allocate the buffer, then call
ETHTOOL_GSTIRNGS and ETHTOOL_GSTATS. If the number of
real_num_queues is changed or flow control attributes
are changed after ETHTOOL_GSSET but before the
ETHTOOL_GSTRINGS/ETHTOOL_GSTATS a user space buffer
overrun occurs.
To fix the overrun always return the max buffer size
needed from get_sset_count() then return all strings
and stats from get_strings()/get_ethtool_stats().
This _will_ change the output from the ioctl() call
which could break applications and script parsing in
theory. I believe these changes should not break existing
tools because the only changes will be more {tx|rx}_queues
and the {tx|rx}_pb_* stats will always be returned.
Existing scripts already need to handle changing number
of queues because this occurs today depending on system
and current features. The {tx|rx}_pb_* stats are at the
end of the output and should be handled by scripts today
regardless.
Finally get_ethtool_stats and get_strings are free-form
outputs tools parsing these outputs should be defensive
anyways. In the end these updates are better then
having a tool segfault because of a buffer overrun.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Users expect the up2tc mapping to be maintained across a DCB
enable/disable/enable transition. And since we maintain all
the other DCB attributes we should do this for up2tc mappings
as well just to be consistent. Also without this we break
user space applications that expect this to occur that
previously worked.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the netdev is already in NETREG_UNREGISTERING/_UNREGISTERED state, do not
update the real num tx queues. netdev_queue_update_kobjects() is already
called via remove_queue_kobjects() at NETREG_UNREGISTERING time. So, when
upper layer driver, e.g., FCoE protocol stack is monitoring the netdev
event of NETDEV_UNREGISTER and calls back to LLD ndo_fcoe_disable() to remove
extra queues allocated for FCoE, the associated txq sysfs kobjects are already
removed, and trying to update the real num queues would cause something like
below:
...
PID: 25138 TASK: ffff88021e64c440 CPU: 3 COMMAND: "kworker/3:3"
#0 [ffff88021f007760] machine_kexec at ffffffff810226d9
#1 [ffff88021f0077d0] crash_kexec at ffffffff81089d2d
#2 [ffff88021f0078a0] oops_end at ffffffff813bca78
#3 [ffff88021f0078d0] no_context at ffffffff81029e72
#4 [ffff88021f007920] __bad_area_nosemaphore at ffffffff8102a155
#5 [ffff88021f0079f0] bad_area_nosemaphore at ffffffff8102a23e
#6 [ffff88021f007a00] do_page_fault at ffffffff813bf32e
#7 [ffff88021f007b10] page_fault at ffffffff813bc045
[exception RIP: sysfs_find_dirent+17]
RIP: ffffffff81178611 RSP: ffff88021f007bc0 RFLAGS: 00010246
RAX: ffff88021e64c440 RBX: ffffffff8156cc63 RCX: 0000000000000004
RDX: ffffffff8156cc63 RSI: 0000000000000000 RDI: 0000000000000000
RBP: ffff88021f007be0 R8: 0000000000000004 R9: 0000000000000008
R10: ffffffff816fed00 R11: 0000000000000004 R12: 0000000000000000
R13: ffffffff8156cc63 R14: 0000000000000000 R15: ffff8802222a0000
ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018
#8 [ffff88021f007be8] sysfs_get_dirent at ffffffff81178c07
#9 [ffff88021f007c18] sysfs_remove_group at ffffffff8117ac27
#10 [ffff88021f007c48] netdev_queue_update_kobjects at ffffffff813178f9
#11 [ffff88021f007c88] netif_set_real_num_tx_queues at ffffffff81303e38
#12 [ffff88021f007cc8] ixgbe_set_num_queues at ffffffffa0249763 [ixgbe]
#13 [ffff88021f007cf8] ixgbe_init_interrupt_scheme at ffffffffa024ea89 [ixgbe]
#14 [ffff88021f007d48] ixgbe_fcoe_disable at ffffffffa0267113 [ixgbe]
#15 [ffff88021f007d68] vlan_dev_fcoe_disable at ffffffffa014fef5 [8021q]
#16 [ffff88021f007d78] fcoe_interface_cleanup at ffffffffa02b7dfd [fcoe]
#17 [ffff88021f007df8] fcoe_destroy_work at ffffffffa02b7f08 [fcoe]
#18 [ffff88021f007e18] process_one_work at ffffffff8105d7ca
#19 [ffff88021f007e68] worker_thread at ffffffff81060513
#20 [ffff88021f007ee8] kthread at ffffffff810648b6
#21 [ffff88021f007f48] kernel_thread_helper at ffffffff813c40f4
Signed-off-by: Yi Zou <yi.zou@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes an issue in which RSC will generate corrupted frames when
PAGE_SIZE is larger than 8K. Specifically it looks like that in 2.6.39 a
change was made so that GRO would always have at least 16 frags available
for coalescing, but the ixgbe RSC logic was not updated. As such the RSC
feature would generate a frame larger than 64K and then overflow the value
in the IP length field.
To correct that I am now basing things on the PAGE_SIZE.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A check for the number of VFs allocated should have used a greater than
equal operator instead of just greater than. This caused allocation of
exactly 32 VFs to not enable the PF transmit and receive enables.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Robert E Garrett <robertX.e.garrett@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
