We only unregister the platform device during the .remove operation,
but if the probe fails we will never reach this sequence.
Suggested-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Fixes: dd96daca6c ("ASoC: SOF: Intel: Add APL/CNL HW DSP support")
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Link: https://lore.kernel.org/r/20210302003410.1178535-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Hi All,
Here is a series of rt5640/rt5651 volume-control fixes which I wrote
while working on a bytcr-rt5640 UCM profile patch-series adding
hardware-volume control to devices using this UCM profile.
The UCM series will also work on older kernels, but it works best on
kernels with this series applied, giving e.g. finer grained volume
control and support for hardware muting the outputs.
Regards,
Hans
Hans de Goede (5):
ASoC: rt5640: Fix dac- and adc- vol-tlv values being off by a factor
of 10
ASoC: rt5651: Fix dac- and adc- vol-tlv values being off by a factor
of 10
ASoC: rt5640: Add emulated 'DAC1 Playback Switch' control
ASoC: rt5640: Rename 'Mono DAC Playback Volume' to 'DAC2 Playback
Volume'
ASoC: Intel: bytcr_rt5640: Add used AIF to the components string
sound/soc/codecs/rt5640.c | 106 +++++++++++++++++++++++---
sound/soc/codecs/rt5640.h | 4 +
sound/soc/codecs/rt5651.c | 4 +-
sound/soc/intel/boards/bytcr_rt5640.c | 11 ++-
4 files changed, 111 insertions(+), 14 deletions(-)
--
2.30.1
Most steps in this table are steps of 3dB (300 centi-dB), so we can
simplify the table.
This not only reduces the amount of space it takes inside the kernel,
this also makes alsa-lib's mixer code actually accept the table, where
as before this change alsa-lib saw the "ADC PGA Gain" control as a
control without a dB scale.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210228160441.241110-1-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
According to the SGTL5000 datasheet [1], the DAP_AVC_CTRL register has
the following bit field definitions:
| BITS | FIELD | RW | RESET | DEFINITION |
| 15 | RSVD | RO | 0x0 | Reserved |
| 14 | RSVD | RW | 0x1 | Reserved |
| 13:12 | MAX_GAIN | RW | 0x1 | Max Gain of AVC in expander mode |
| 11:10 | RSVD | RO | 0x0 | Reserved |
| 9:8 | LBI_RESP | RW | 0x1 | Integrator Response |
| 7:6 | RSVD | RO | 0x0 | Reserved |
| 5 | HARD_LMT_EN | RW | 0x0 | Enable hard limiter mode |
| 4:1 | RSVD | RO | 0x0 | Reserved |
| 0 | EN | RW | 0x0 | Enable/Disable AVC |
The original default value written to the DAP_AVC_CTRL register during
sgtl5000_i2c_probe() was 0x0510. This would incorrectly write values to
bits 4 and 10, which are defined as RESERVED. It would also not set
bits 12 and 14 to their correct RESET values of 0x1, and instead set
them to 0x0. While the DAP_AVC module is effectively disabled because
the EN bit is 0, this default value is still writing invalid values to
registers that are marked as read-only and RESERVED as well as not
setting bits 12 and 14 to their correct default values as defined by the
datasheet.
The correct value that should be written to the DAP_AVC_CTRL register is
0x5100, which configures the register bits to the default values defined
by the datasheet, and prevents any writes to bits defined as
'read-only'. Generally speaking, it is best practice to NOT attempt to
write values to registers/bits defined as RESERVED, as it generally
produces unwanted/undefined behavior, or errors.
Also, all credit for this patch should go to my colleague Dan MacDonald
<dmacdonald@curbellmedical.com> for finding this error in the first
place.
[1] https://www.nxp.com/docs/en/data-sheet/SGTL5000.pdf
Signed-off-by: Benjamin Rood <benjaminjrood@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20210219183308.GA2117@ubuntu-dev
Signed-off-by: Mark Brown <broonie@kernel.org>
The adc_vol_tlv volume-control has a range from -17.625 dB to +30 dB,
not -176.25 dB to + 300 dB. This wrong scale is esp. a problem in userspace
apps which translate the dB scale to a linear scale. With the logarithmic
dB scale being of by a factor of 10 we loose all precision in the lower
area of the range when apps translate things to a linear scale.
E.g. the 0 dB default, which corresponds with a value of 47 of the
0 - 127 range for the control, would be shown as 0/100 in alsa-mixer.
Since the centi-dB values used in the TLV struct cannot represent the
0.375 dB step size used by these controls, change the TLV definition
for them to specify a min and max value instead of min + stepsize.
Note this mirrors commit 3f31f7d9b5 ("ASoC: rt5670: Fix dac- and adc-
vol-tlv values being off by a factor of 10") which made the exact same
change to the rt5670 codec driver.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210226143817.84287-3-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The adc_vol_tlv volume-control has a range from -17.625 dB to +30 dB,
not -176.25 dB to + 300 dB. This wrong scale is esp. a problem in userspace
apps which translate the dB scale to a linear scale. With the logarithmic
dB scale being of by a factor of 10 we loose all precision in the lower
area of the range when apps translate things to a linear scale.
E.g. the 0 dB default, which corresponds with a value of 47 of the
0 - 127 range for the control, would be shown as 0/100 in alsa-mixer.
Since the centi-dB values used in the TLV struct cannot represent the
0.375 dB step size used by these controls, change the TLV definition
for them to specify a min and max value instead of min + stepsize.
Note this mirrors commit 3f31f7d9b5 ("ASoC: rt5670: Fix dac- and adc-
vol-tlv values being off by a factor of 10") which made the exact same
change to the rt5670 codec driver.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210226143817.84287-2-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When I added the quirk for the "HP Pavilion x2 10-p0XX" I copied the
byt_rt5640_quirk_table[] entry for the HP Pavilion x2 10-k0XX / 10-n0XX
models since these use almost the same settings.
While doing this I accidentally also copied and kept the non-standard
OVCD_TH_1500UA setting used on those models. This too low threshold is
causing headsets to often be seen as headphones (without a headset-mic)
and when correctly identified it is causing ghost play/pause
button-presses to get detected.
Correct the HP Pavilion x2 10-p0XX quirk to use the default OVCD_TH_2000UA
setting, fixing these problems.
Fixes: fbdae7d6d0 ("ASoC: Intel: bytcr_rt5640: Fix HP Pavilion x2 Detachable quirks")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210224105052.42116-1-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Hi All,
While working on adding hardware-volume control support to the UCM
profile for the rt5672 and on adding LED trigger support to the
rt5670 codec driver. I hit / noticed a couple of issues this series
fixes these issues.
Regards,
Hans
Hans de Goede (4):
ASoC: rt5670: Remove 'OUT Channel Switch' control
ASoC: rt5670: Remove 'HP Playback Switch' control
ASoC: rt5670: Remove ADC vol-ctrl mute bits poking from Sto1 ADC mixer
settings
ASoC: rt5670: Add emulated 'DAC1 Playback Switch' control
sound/soc/codecs/rt5670.c | 110 +++++++++++++++++++++++++++++++++-----
sound/soc/codecs/rt5670.h | 9 ++--
2 files changed, 101 insertions(+), 18 deletions(-)
--
2.30.1
Add missed MODULE_DEVICE_TABLE for the driver can be loaded
automatically at boot.
Fixes: 9208847774 ("ASoC: ak5558: Add support for AK5558 ADC driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1614149872-25510-2-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add missed MODULE_DEVICE_TABLE for the driver can be loaded
automatically at boot.
Fixes: 08660086ef ("ASoC: ak4458: Add support for AK4458 DAC driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1614149872-25510-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
For reliable output-mute LED control we need a "DAC1 Playback Switch"
control. The "DAC Playback volume" control is the only control in the
path from the DAC1 data input to the speaker output, so the UCM profile
for the speaker output will have its PlaybackMixerElem set to "DAC1".
But userspace (pulseaudio) will set the "DAC1 Playback Volume" control to
its softest setting (which is not fully muted) while still showing the
speaker as being enabled at a low volume in the UI.
If we were to set the SNDRV_CTL_ELEM_ACCESS_SPK_LED on the "DAC1 Playback
Volume" control, this would mean then what pressing KEY_VOLUMEDOWN the
speaker-mute LED (embedded in the volume-mute toggle key) would light
while the UI is still showing the speaker as being enabled at a low
volume, meaning that the UI and the LED are out of sync.
Only after an _extra_ KEY_VOLUMEDOWN press would the UI show the
speaker as being muted.
The path from DAC1 data input to the speaker output does have
a digital mixer with DAC1's data as one of its inputs direclty after
the "DAC1 Playback Volume" control.
This commit adds an emulated "DAC1 Playback Switch" control by:
1. Declaring the enable flag for that mixers DAC1 input as well as the
"DAC1 Playback Switch" control both as SND_SOC_NOPM controls.
2. Storing the settings of both controls as driver-private data
3. Only clearing the mute flag for the DAC1 input of that mixer if the
stored values indicate both controls are enabled.
This is a preparation patch for adding "audio-mute" LED trigger support.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210215142118.308516-5-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The SND_SOC_DAPM_MIXER declaration for "Sto1 ADC MIXL" and "Sto1 ADC MIXR"
was using the mute bits from the RT5670_STO1_ADC_DIG_VOL control as mixer
master mute bits.
But these bits are already exposed to userspace as controls as part of the
"ADC Capture Volume" / "ADC Capture Switch" control pair:
SOC_DOUBLE("ADC Capture Switch", RT5670_STO1_ADC_DIG_VOL,
RT5670_L_MUTE_SFT, RT5670_R_MUTE_SFT, 1, 1),
SOC_DOUBLE_TLV("ADC Capture Volume", RT5670_STO1_ADC_DIG_VOL,
RT5670_L_VOL_SFT, RT5670_R_VOL_SFT,
127, 0, adc_vol_tlv),
Both the fact that the mute bits belong to the same reg as the vol-ctrl
and the "Digital Mixer Path" diagram in the datasheet clearly shows that
these mute bits are not part of the mixer and having 2 separate controls
poking at the same bits is a bad idea.
Remove the master-mute bits settings from the "Sto1 ADC MIXL" and
"Sto1 ADC MIXR" DAPM widget declarations, avoiding these bits getting
poked from 2 different places.
This should not cause any issues for userspace. AFAICT the rt567x codecs
are only used on x86/ACPI devices and the UCM profiles used there already
set the "ADC Capture Switch" as needed.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210215142118.308516-4-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The RT5670_L_MUTE_SFT and RT5670_R_MUTE_SFT bits (bits 15 and 7) of the
RT5670_HP_VOL register are set / unset by the headphones deplop code
run by rt5670_hp_event() on SND_SOC_DAPM_POST_PMU / SND_SOC_DAPM_PRE_PMD.
So we should not also export a control to userspace which toggles these
same bits.
This should not cause any issues for userspace. AFAICT the rt567x codecs
are only used on x86/ACPI devices and the UCM profiles used there do not
use the "HP Playback Switch" control.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210215142118.308516-3-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The "OUT Channel Switch" control is a left over from code copied from
thr rt5640 codec driver.
With the rt5640 codec driver the output volume controls have 2 pairs of
mute bits:
bit 7, 15: Mute Control for Spk/Headphone/Line Output Port
bit 6, 14: Mute Control for Spk/Headphone/Line Volume Channel
Bits 7 and 15 are normal mute bits on the rt5670/5672 which are
controlled by 2 dapm widgets:
SND_SOC_DAPM_SWITCH("LOUT L Playback", SND_SOC_NOPM, 0, 0,
&lout_l_enable_control),
SND_SOC_DAPM_SWITCH("LOUT R Playback", SND_SOC_NOPM, 0, 0,
&lout_r_enable_control),
But on the 5670/5672 bit 6 is always reserved, where as bit 14 is
"LOUT Differential Mode" on the 5670 and also reserved on the 5672.
So the "OUT Channel Switch" control which is controlling bits 6+14
of the "LINE Output Control" register is bogus -> remove it.
This should not cause any issues for userspace. AFAICT the rt567x codecs
are only used on x86/ACPI devices and the UCM profiles used there do not
use the "OUT Channel Switch" control.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210215142118.308516-2-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When using the driver in I2S TDM mode, the _fsl_ssi_set_dai_fmt()
function rewrites the number of slots previously set by the
fsl_ssi_set_dai_tdm_slot() function to 2 by default.
To fix this, let's use the saved slot count value or, if TDM
is not used and the slot count is not set, proceed as before.
Fixes: 4f14f5c11d ("ASoC: fsl_ssi: Fix number of words per frame for I2S-slave mode")
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Link: https://lore.kernel.org/r/20210216114221.26635-1-shc_work@mail.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
There is potential read of the uninitialized variable ec_tx if the call
to snd_soc_component_read fails or returns an unrecognized w->name. To
avoid this corner case, initialize ec_tx to -1 so that it is caught
later when ec_tx is bounds checked.
Addresses-Coverity: ("Uninitialized scalar variable")
Fixes: 4f692926f5 ("ASoC: codecs: lpass-rx-macro: add dapm widgets and route")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20210215163313.84026-1-colin.king@canonical.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The ACPI scan capabilities is called from the intel-dspconfig as well
as the SOF/HDaudio drivers. This creates dependencies and randconfig issues
when HDaudio and SOF/SoundWire are not all configured as modules.
To simplify Kconfig dependencies between HDAudio, SoundWire, SOF and
intel-dspconfig, move the ACPI scan helpers to a dedicated
module. This follows the same idea as NHLT helpers which are already
handled as a dedicated module.
The only functional change is that the kernel parameter to filter
links is now handled by a different module, but that was only provided
for developers needing work-arounds for early BIOS releases.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Bard Liao <bard.liao@intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20210302003125.1178419-7-pierre-louis.bossart@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Kconfig file is way too convoluted. Track platforms where
SoundWire is supported, and add simpler conditions to make sure there
is no module/built-in issue.
The use of 'depends on' is less intuitive if a required 'depend' is
missing, but that's a small price to pay for clarity and simplicity.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Bard Liao <bard.liao@intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20210302003125.1178419-6-pierre-louis.bossart@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There is no reason why we should call the intel_dspcfg helpers from
common code, this should be moved in Intel-specific code and only
called from platforms where a conflict may occur with the HDaudio or
SST/Skylake driver.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Bard Liao <bard.liao@intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20210302003125.1178419-5-pierre-louis.bossart@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Move PCI IDs and device-specific definitions out of common code. No
functionality change for now, just code split and removal of
IF_ENABLED() which made the configurations too complicated in case of
reuse of IP across generations.
Additional changes to address the DSP_CONFIG case and SoundWire
depends/select confusions are provided in follow-up patches.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Bard Liao <bard.liao@intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20210302003125.1178419-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The SOF-ACPI driver is backwards from the normal Linux model, it has a
generic driver that knows about all the specific drivers, as opposed to
having hardware specific drivers that link against a common framework.
This requires ugly Kconfig magic and leads to missed dependencies as
seen in this link error:
arm-linux-gnueabi-ld: sound/soc/sof/sof-pci-dev.o: in function `sof_acpi_probe':
sof-pci-dev.c:(.text+0x1c): undefined reference to `snd_intel_dsp_driver_probe'
Change it to use the normal probe order of starting with a specific
device in a driver, turning the sof-acpi-dev.c driver into a
library (exported symbols are name-spaced to avoid symbol pollution).
For backwards-compatibility with previous Kconfigs, the default values
for platform drivers uses the top-level ACPI configurations. The
modules were also renamed to allow for gradual transitions in test
scripts.
Co-developed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Bard Liao <bard.liao@intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20210302003125.1178419-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Another quiet release in terms of features, though several of the
drivers got quite a bit of work and there were a lot of general changes
resulting from Morimoto-san's ongoing cleanup work.
- As ever, lots of hard work by Morimoto-san cleaning up the code and
making it more consistent.
- Many improvements in the Intel drivers including a wide range of
quirks and bug fixes.
- A KUnit testsuite for the topology code.
- Support for Ingenic JZ4760(B), Intel AlderLake-P, DT configured
nVidia cards, Qualcomm lpass-rx-macro and lpass-tx-macro
- Removal of obsolete SIRF prima/atlas, Txx9 and ZTE zx drivers.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmAtZ7cACgkQJNaLcl1U
h9DD5Af/eeERQ2uVOqtw0If+XL1xRYe6RewgDoNcO/l/5WxBLrBH6NbEf0OwNJeg
vzZAkUBtxmx6XiW2M/h+4ucW1OPcg5IzxIWTHfGDMlKIxzb0jgWugRnJ7sdTnOs3
c+QHnvuOT7QzZBviAIkc5uZ5thAImYF8zDyKoGF5llztmnBYymtgpnvnRNZGM0ou
76oUzSvkCFI2b0Yf6bpGok2nBVlOu82HSHOUKjXVWk+LAeiivlYGOEZpdIKEe3S8
u6atQJ29XRr52Yuc2z4xnFQTW1cIDlwj2Fk5x/z8hX+5nRhNSGuIv1l5m7TfBj3e
mCO9cltKZxly0NXysgekn95JHwwwkA==
=MJSb
-----END PGP SIGNATURE-----
Merge tag 'asoc-v5.12' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Updates for v5.12
Another quiet release in terms of features, though several of the
drivers got quite a bit of work and there were a lot of general changes
resulting from Morimoto-san's ongoing cleanup work.
- As ever, lots of hard work by Morimoto-san cleaning up the code and
making it more consistent.
- Many improvements in the Intel drivers including a wide range of
quirks and bug fixes.
- A KUnit testsuite for the topology code.
- Support for Ingenic JZ4760(B), Intel AlderLake-P, DT configured
nVidia cards, Qualcomm lpass-rx-macro and lpass-tx-macro
- Removal of obsolete SIRF prima/atlas, Txx9 and ZTE zx drivers.
Hi All,
Here is a patch series adding quirks with device-specific settings for
4 more tablet / 2-in-1 models.
Regards,
Hans
Hans de Goede (4):
ASoC: Intel: bytcr_rt5640: Add quirk for the Estar Beauty HD MID 7316R tablet
ASoC: Intel: bytcr_rt5640: Add quirk for the Voyo Winpad A15 tablet
ASoC: Intel: bytcr_rt5651: Add quirk for the Jumper EZpad 7 tablet
ASoC: Intel: bytcr_rt5640: Add quirk for the Acer One S1002 tablet
sound/soc/intel/boards/bytcr_rt5640.c | 37 +++++++++++++++++++++++++++
sound/soc/intel/boards/bytcr_rt5651.c | 13 ++++++++++
2 files changed, 50 insertions(+)
--
2.30.1
In case DPCM runtime has multiple CPU DAIs, dpcm_init_runtime_hw() is
called multiple times, once for each CPU DAI. This will lead to
ignoring hw limits of all but the last DAI.
Fix this by moving soc_pcm_hw_init() up by one level to
dpcm_init_runtime_hw().
Fixes: 140f553d12 ("ASoC: soc-pcm: fix hwparams min/max init for dpcm")
Suggested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20210216172251.3023723-1-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The Acer One S1002 tablet is using an analog mic on IN1 and has
its jack-detect connected to JD2_IN4N, instead of using the default
IN3 for its internal mic and JD1_IN4P for jack-detect.
Note it is also using AIF2 instead of AIF1 which is somewhat unusual,
this is correctly advertised in the ACPI CHAN package, so the speakers
do work without the quirk.
Add a quirk for the mic and jack-detect settings.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210216213555.36555-5-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a DMI quirk for the Jumper EZpad 7 tablet, this tablet has
a jack-detect switch which reads 1/high when a jack is inserted,
rather then using the standard active-low setup which most
jack-detect switches use. All other settings are using the defaults.
Add a DMI-quirk setting the defaults + the BYT_RT5651_JD_NOT_INV
flags for this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210216213555.36555-4-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The Voyo Winpad A15 tablet uses a Bay Trail (non CR) SoC, so it is using
SSP2 (AIF1) and it mostly works with the defaults. But instead of using
DMIC1 it is using an analog mic on IN1, add a quirk for this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210216213555.36555-3-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The Estar Beauty HD MID 7316R tablet almost fully works with out default
settings. The only problem is that it has only 1 speaker so any sounds
only playing on the right channel get lost.
Add a quirk for this model using the default settings + MONO_SPEAKER.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210216213555.36555-2-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When runtime is initialized with dpcm_init_runtime_hw(), some of the
min/max calculations assume that defaults are set. For example
calculation of channel min/max values may be done using zero-initialized
data and soc_pcm_hw_update_chan() will always return max-channels of 0
in this case. This will result in failure to open the PCM at all.
Fix the issue by calling soc_pcm_hw_init() before calling any
soc_pcm_hw_update_*() functions.
Remove the conditional code on runtime->hw.formats as this field
is anyways set in soc_pcm_hw_init().
Fixes: 6cb56a4549 ("ASoC: soc-pcm: add soc_pcm_hw_update_chan()")
Reported-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20210214220414.2876690-1-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We have soc_pcm_hw_update_xxx() now.
This patch creates same function for format.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/87pn1g90oa.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We have soc_pcm_hw_update_rate() now.
This patch creates same function for chan.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/87r1lw90oo.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
To update hw, we need to follow setting order
1) set hw->rates
2) call snd_pcm_limit_hw_rates()
3) update hw->rate_min/max
To avoid random settings, this patch adds new soc_pcm_hw_update_rate()
and share updating code.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/87sg6c90qv.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This callback structure has never been used and it is not clear why it
was added in the first place. Remove it to clear up the code a little.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210211172106.16258-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
With recent SOF 1.7 pre-releases, kernel has been emitting following
warnings at probe:
[10006.645216] sof-audio-pci 0000:00:1f.3: warn: FW ABI is more recent than kernel
[10006.652137] sof-audio-pci 0000:00:1f.3: warn: topology ABI is more recent than kernel
The warnings are emitted due to increase of the patch-level in firmware
mainline (to 3.17.1). But the patch level should not be considered even
in the strict ABI check, so modify the kernel side logic that makes the
check and only consider the major.minor components.
BugLink: https://github.com/thesofproject/linux/issues/2647
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20210211172440.2371447-1-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
It is recommended to not specifiy clocks property in an endpoint subnode.
This series moves clocks to device node.
However after moving the clocks to device node, the audio playback or
capture fails. The specified clock is not actually getting enabled and
hence the failure is seen. There seems to be a bug in simple-card-utils.c
where clock handle is not assigned when parsing clocks from device node.
Fix the same and revert original change which actually added clocks
property in endpoint subnode. Also update Jetson AGX Xavier DT where the
usage is found.
Sameer Pujar (3):
ASoC: simple-card-utils: Fix device module clock
Revert "ASoC: audio-graph-card: Add clocks property to endpoint node"
arm64: tegra: Move clocks from RT5658 endpoint to device node
.../devicetree/bindings/sound/audio-graph-port.yaml | 3 ---
arch/arm64/boot/dts/nvidia/tegra194-p2972-0000.dts | 2 +-
sound/soc/generic/simple-card-utils.c | 13 ++++++-------
3 files changed, 7 insertions(+), 11 deletions(-)
--
2.7.4
Qualcomm LPASS (Low Power Audio SubSystem) has internal codec
TX macro block which is used for connecting with external
Soundwire TX Codecs like WCD938x.
This patch adds support to the codec part of the TX Macro block
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20210211122735.5691-7-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
LPASS RX Codec Macro is available in Qualcomm LPASS (Low Power Audio SubSystem).
This is used for connecting with SoundWire devices like WCD938x Codecs to provide
headphone/ear/lineout functionality.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20210211122735.5691-3-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
If "clocks = <&xxx>" is specified from the CPU or Codec component
device node, the clock is not getting enabled. Thus audio playback
or capture fails.
Fix this by populating "simple_dai->clk" field when clocks property
is specified from device node as well. Also tidy up by re-organising
conditional statements of parsing logic.
Fixes: bb6fc620c2 ("ASoC: simple-card-utils: add asoc_simple_card_parse_clk()")
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Link: https://lore.kernel.org/r/1612939421-19900-2-git-send-email-spujar@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
SoundWire machine drivers make a heavy use of component prefixes to
uniquify control names. This however results in errors when looking
for widgets or pins. This patchset suggests two solutions but feedback
or suggestions on how to take the prefix into account would be
welcome.
Bard Liao (1):
ASoC: Intel: boards: max98373: get dapm from cpu_dai
Shuming Fan (1):
ASoC: dapm: use component prefix when checking widget names
sound/soc/intel/boards/sof_maxim_common.c | 5 +++--
sound/soc/soc-dapm.c | 13 ++++++++++++-
2 files changed, 15 insertions(+), 3 deletions(-)
--
2.25.1
HP Spectre x360 convertible devices rely on a mixed SoundWire+DMIC
configuration which wasn't well supported. This lead to the discovery
that we missed the TGL_HDMI quirk on a number of Dell devices, the
addition of DMIC autodetection (based on NHLT tables), the addition of
new component strings needed by UCM, and work-arounds due to
problematic DSDT tables.
Changes since v1:
Rebase to remove first three patches already merged.
Fix allmodconfig issues (undeclared kernel parameter)
Bard Liao (1):
ASoC: intel: sof_sdw: add trace for dai links
Guennadi Liakhovetski (1):
ASoC: SOF: Intel: HDA: don't keep a temporary variable
Pierre-Louis Bossart (8):
ASoC: Intel: sof_sdw: reorganize quirks by generation
ASoC: Intel: sof-sdw: indent and add quirks consistently
ASoC: Intel: sof_sdw: add quirk for HP Spectre x360 convertible
ASoC: Intel: sof_sdw: add mic:dmic and cfg-mics component strings
ASoC: Intel: soc-acpi: add ACPI matching table for HP Spectre x360
ASoC: SOF: Intel: SoundWire: refine ACPI match
ASoC: SOF: Intel: detect DMIC number in SoundWire mixed config
ASoC: SOF: Intel: hda: add dev_dbg() when DMIC number is overridden
Rander Wang (1):
ASoC: Intel: sof_sdw: detect DMIC number based on mach params
sound/soc/intel/boards/sof_sdw.c | 134 ++++++-----
.../intel/common/soc-acpi-intel-tgl-match.c | 20 ++
sound/soc/sof/intel/hda.c | 212 ++++++++++++------
3 files changed, 244 insertions(+), 122 deletions(-)
--
2.25.1
With current delayed probe implementation, sof_probe_complete is not
called in case of errors. And as this function is responsible for
decrementing runtime pm usage counter, this will result in following
problem:
- probe driver in conditions where probe will fail (to force
the condition on Intel SOF systems, set
"snd_sof_intel_hda_common.codec_mask=0")
- unload driver (runtime-pm usage_count is leaked)
- fix the issue by installing missing fw, modifying module parameters,
etc actions
- try to load driver again -> success, probe ok
-> device never enters runtime suspend
Fix the issue by storing result of delayed probe to a state variable and
providing new snd_sof_device_probe_completed() to be queried from SOF
PCI/ACPI/OF drivers.
If probe never completed successfully, runtime PM was not set up and
thus at remove(), we should not increment usage count anymore.
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@intel.com>
Link: https://lore.kernel.org/r/20210210105237.2179273-1-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This log message should be a debug message, because it
doesn't return directly but continue next loop.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/1612771965-5776-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
It's useful for debug and system integration to show cases where we
ignore the number of microphones reported by NHLT.
Suggested-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20210208233336.59449-12-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
