When unmasking a GPIO interrupt on a BF54x part, the code will implicitly
ack any pending interrupts. This is not what unmasking should do and can
cause people to miss interrupts from their devices, so punt the code.
Reported-by: Rutger Hofman <rutger@cs.vu.nl>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The low level assembly needs to use the pseudo_long_call helper so that
we use the right call insn when doing kernel XIP.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Since linux-2.6.31, the kernel suspend framework will do disable_irq/enable_irq,
so save/restore irq in standby and suspend to mem callback should be dropped.
Otherwise the common code notices things are enabled and complains.
Signed-off-by: Steven Miao <realmz6@gmail.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Currently, sending an interprocessor interrupt (IPI) requires building up
a message dynamically which means memory allocation. But often times, we
will want to send an IPI in low level contexts where allocation is not
possible which may lead to a panic(). So create a per-cpu static array
for the message queue and use that instead.
Further, while we have two supplemental interrupts, we are currently only
using one of them. So use the second one for the most common IPI message
of all -- smp_send_reschedule(). This avoids ugly contention for locks
which in turn would require an IPI message ...
In general, this improves SMP performance, and in some cases allows the
SMP port to work in places it wouldn't before. Such as the PREEMPT_RT
state where the slab is protected by a per-cpu spin lock. If the slab
kmalloc/kfree were to put the task to sleep, and that task was actually
the IPI handler, then the system falls down yet again.
After running some various stress tests on the system, the static limit
of 5 messages seems to work. On the off chance even this overflows, we
simply panic(), and we can review that scenario to see if the limit needs
to be increased a bit more.
Signed-off-by: Yi Li <yi.li@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This function takes an irq_handler_t function, but the prototype in
the header doesn't match the function definition. This is due to the
smp headers needing to avoid circular dependencies. So change the
function to take a simple pointer.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The cpu maps are defines provided by common linux/cpumask.h, not local
variables. So stop exporting them locally and include the right header
for their definition.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This code was useful during early port development when our icache code
wasn't solid, but that ship has sailed long ago, and no code calls this
function anymore (irq_panic). So punt it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This matches all the other Blackfin ports and keep us from having to write
bf561-specific code in many places.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Flushing caches sometimes requires anomaly workarounds which require
supervisor-only insns. Normally we don't need to flush caches from
userspace so this isn't a problem, but when gcc generates trampolines
on the stack, we do.
So add a new syscall for gcc to use modeled after the mips version.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Make sure we include EMAC_SYSTAT when showing errors.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Rename h/w IRQ flags handling functions to be in line with what is expected for
the irq renaming patch. This renames local_*_hw() to hard_local_*() using the
following perl command:
perl -pi -e 's/local_irq_(restore|enable|disable)_hw/hard_local_irq_\1/ or s/local_irq_save_hw([_a-z]*)[(]flags[)]/flags = hard_local_irq_save\1()/' `find arch/blackfin/ -name "*.[ch]"`
and then fixing up asm/irqflags.h manually.
Additionally, arch/hard_local_save_flags() and arch/hard_local_irq_save() both
return the flags rather than passing it through the argument list.
Signed-off-by: David Howells <dhowells@redhat.com>
The RTC ISTAT bits do not affect wakeups, and the RTC driver already
takes care of clearing this MMR when necessary. So drop the useless
clearing in the core Blackfin power code.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The dma_memcpy() function takes care of flushing different caches for us.
Normally this is what we want, but when resuming from mem, we don't yet
have caches enabled. If these functions happen to be placed into L1 mem
(which is what we're trying to relocate), then things aren't going to
work. So define a non-cache dma_memcpy() variant to utilize in situations
like this.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Anomaly 05000491 says that IFLUSH cannot have certain types of memory
stalls triggered before it has completed in order to function correctly.
One such condition is that it be in L1 instruction. So add a config
option to move it there, default it to on, and throw up a warning when
it is turned off and this anomaly exists.
Since the anomaly should be worked around, we can drop the older method
of calling IFLUSH multiple times.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Design found that these anomalies had the same root issue, so they've
merged 475 into 220. We need to do the same to update to the latest
anomaly sheets.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Tweak the for loops that operate on the SIC IAR system MMRs to avoid
re-reading them multiple times in a row. System MMRs are a little
slower to access, so avoid the penalty when possible.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This patch removes a custom GPIO wakeup API which allowed GPIOs to act
as wakeup sources, which are not configured as Interrupts.
This API is a leftover from the time before irq_wake was established.
From now on people must use enable_irq_wake(GPIO_IRQx) and the GPIO in
question needs to be configured as Interrupt.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Need to make sure we update the loops_per_jiffy values when we start
changing the core clock.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The exact hardware error handling code was added before the workaround
for anomaly 283 which caused the anomaly to be triggered in some cases
(an infinite core stall). So re-order the code to avoid this.
Reported-by: Andrew Rook <andrew.rook@speakerbus.co.uk>
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The on-chip keypad peripheral requires different registers to be setup
depending on the standby type (standby vs hibernation). However, since
the power management framework doesn't differentiate between these types,
the driver doesn't know which registers to program and subsequently it
avoids doing so.
Always enabling the keyboard wakeup source causes misbehavior when the
pins are not assigned to the keypad. If they happen to drive a certain
level, they'll trigger a wake up event which is not wanted. So until
the aforementioned issue can be sorted out, drop support for the
wakeup source completely.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This patch provides infrastructure for MAC Wake-On-Lan and PHYINT use in
phylib. New Interrupts added:
IRQ_MAC_PHYINT /* PHY_INT Interrupt */
IRQ_MAC_MMCINT /* MMC Counter Interrupt */
IRQ_MAC_RXFSINT /* RX Frame-Status Interrupt */
IRQ_MAC_TXFSINT /* TX Frame-Status Interrupt */
IRQ_MAC_WAKEDET /* Wake-Up Interrupt */
IRQ_MAC_RXDMAERR /* RX DMA Direction Error Interrupt */
IRQ_MAC_TXDMAERR /* TX DMA Direction Error Interrupt */
IRQ_MAC_STMDONE /* Station Mgt. Transfer Done Interrupt */
On BF537/6 the implementation is not straight forward since there are now
two chained chained_handlers. A cleaner approach would have been to add
latter IRQs to the demux of IRQ_GENERIC_ERROR.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
We want to report all system calls (even invalid ones) to the tracing
layers, so check the NR only after we've notified.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
On Blackfin systems, the hardware single step exception triggers before
the system call exception, so we need to save this info to process it
later on. Otherwise, single stepping in userspace misses a few insns
right after the system call.
This is based a bit on the SuperH code added in commit 4b505db9c4.
Reported-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This functions are implicitly called by core functions like cpu_relax(),
and since those functions may be called early on before common code has
initialized the per-cpu data area, we need to tweak the stats gathering.
Now the statistics are maintained in common bss which makes these funcs
safe to use as soon as the C runtime env is setup.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This makes room for off-chip IRQ controllers.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
During very early init, the stack pointer is given a slightly incorrect
value (&init_thread_union). The value is later adjusted to the right one
during early init (&init_thread_union + THREAD_SIZE), but it is used a few
times in between. While the few functions used don't actually put things
onto the stack (due to optimization), it's best if we simply use the right
value from the start.
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
SMP systems require per-cpu local clock event devices in order to enable
HRT support. One a BF561, we can use local core timer for this purpose.
Originally, there was one global core-timer clock event device set up for
core A.
To accomplish this feat, we need to split the gptimer0/core timer logic
so that each is a standalone clock event. There is no requirement that
we only have one clock event source anyways. Once we have this, we just
define per-cpu clock event devices for each local core timer.
Signed-off-by: Yi Li <yi.li@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Now that the Blackfin IRQ controller supports this, drivers get the normal
functionality of controlling which CPU to bind IRQs to.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Sometimes a SMP system will randomly panic at boot. This is due to caches
being out of sync when one core tries to signal the other. So when one
core calls another via IPI, flush the data caches.
Signed-off-by: Yi Li <yi.li@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The error masks are only needed in the BF537 demux error code, so instead
of needing all the short peripheral defines in global space, push these
masks into the one file where they are actually needed. This fixes a
bunch of define collisions with common code (can/serial/etc...).
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Barry Song <barry.song@analog.com>
When testing PREEMPT_RT kernel on BF561-EZKit, the kernel blocks while
booting. When the kernel initializes the ethernet driver, it sleeps and
never wakes up.
The issue happens when the kernel waits for a timer for Core B to timeout
(the timers are per-cpu based: static DEFINE_PER_CPU(struct tvec_base *,
tvec_bases) = &boot_tvec_bases).
However, the ksoftirqd thread for Core B (note, the ksoftirqd thread is
also per-cpu based) cannot work properly, and the timers for Core B never
times out.
When ksoftirqd() for the first time runs on core B, it is possible core A
is still initializing core B (see smp_init() -> cpu_up() -> __cpu_up()).
So the "cpu_is_offline()" check may return true and ksoftirqd moves to
"wait_to_die".
So delay the core b start up until the per-cpu timers have been set up
fully.
Signed-off-by: Yi Li <yi.li@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The GPIOs on ports C/D/E on the BF538/BF539 do not behave the same way as
the other ports on the part and the same way as all other Blackfin parts.
The MMRs are programmed slightly different and they cannot be used to
generate interrupts or wakeup a sleeping system. Since these guys don't
fit into the existing code, create a simple gpiolib driver for them.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
PLL_LOCKCNT applies only to the PLL programming sequence which does not
apply to core and system clock dividers. Writes to PLL_DIV to change the
CSEL/SSEL dividers take effect immediately.
There is still overhead in software in writing the new dividers, so just
use a value of 50us as this should be good enough.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
