We need an accurate and continuous (monotonic) time sources to do
accurate synchronization among more timing sources. This patch allows
to enable monotonic timestamps for ALSA PCM devices and enables monotonic
timestamps for ALSA timer devices.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Add a comment that explains why the 'Modem' control doesn't work with
newer chips.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
On version 39 or newer chips, we better remove the 'Modem' control
because this register bit now mutes the front channels of the
multichannel stream.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The attached patch should fix typo in auto initialization verbs for ALC883
codec.
Signed-off-by: Andy Shevchenko <andy@smile.org.ua>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
* support for switching rate in STAC9460 - using set_rate_val of the akm
infrastructure
* listing all STAC9460 registers in proc
* disabling mpu401 device for Prodigy192 - otherwise the currently
flawed mpu401 code hangs kernel when opening the midi device
* removing old unused commented-out code
Signed-off-by: Pavel Hofman <dustin@seznam.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This removes the pnp_resource_change use from the ALSA ISAPnP drivers. In
2.4 these were useful in providing an easy path to setting the resources,
but in 2.6 they retain function as a layering violation only.
This makes for a nice cleanup (-550 lines) of ALSA but moreover, ALSA is the
only remaining user of pnp_init_resource_table(), pnp_resource_change() and
pnp_manual_config_dev() (and, in fact, of 'struct pnp_resource_table') in
the tree outide of drivers/pnp itself meaning it makes for more cleanup
potential inside the PnP layer.
Thomas Renninger acked their removal from that side, you did from the ALSA
side (CC list just copied from that thread).
Against current alsa-kernel HG. Many more potential cleanups in there, but
this _only_ removes the pnp_resource_change code. Compile tested against
current alsa-kernel HG and compile- and use-tested against 2.6.23.x (few
offsets).
Cc: Thomas Renninger <trenn@suse.de>
Signed-off-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
There should be a pci_dev_put when breaking out of a loop that iterates
over calls to pci_get_device and similar functions.
In this case, the return under the initial if needs a pci_dev_put in the
same way that the return under the subsequent for loop has a pci_dev_put.
This was fixed using the following semantic patch.
// <smpl>
@@
type T;
identifier d;
expression e;
@@
T *d;
...
while ((d = \(pci_get_device\|pci_get_device_reverse\|pci_get_subsys\|pci_get_class\)(..., d)) != NULL)
{... when != pci_dev_put(d)
when != e = d
(
return d;
|
+ pci_dev_put(d);
? return ...;
)
...}
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The 'Word Clock Status' control on Delta 1010LT checks the CS8427
error register too strictly and almost always returns 1 (unlocked).
It should check only the lock status bit.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added support for Native Instrument's Kore controller 2. This device has
no audio but MIDI, input devices and ALSA controllers only.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Disable the simultaneous load feature for the line in and headphone
out volume registers. This allows left and right volume levels to
be controlled separately.
Signed-off-by: Ville Syrjala <syrjala@sci.fi>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added the missing snd_card_set_dev() call. This will fix the incomplete
sysfs entry for this card.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Set a proper error code in the error path of i2sbus_attach_codec().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The aoa driver is not specifying constraints on number of periods, and, it
seems, it might end with a non-integer number, which it cannot deal with.
Fix by adding a proper constraint.
Signed-off-by: Heikki Lindholm <holindho@cs.helsinki.fi>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
When MMAP time-stamp mode is given, it's supposed to update the time-stamp
only at period boundary. However, it currently updates at each status call
so this is just useless. The patch fixes this misbehavior.
Also it fixes the wrong check of tstamp_mode (don't use bit-and for enum).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
- added support for all input controllers on Native Instrument's 'Kore
controller'.
- added ALSA controls to switch LEDs on 'RigKontrol 2', 'RigKontrol3',
'Audio Kontrol 1' and 'Kore controller'.
- added ALSA controls to switch input mode, software lock and ground
lift features on 'Audio 8 DJ'.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
- link input device with its parent so that it placed in proper spot
in sysfs hierarchy
- drivers that allow changing their keymaps should use private copy
of the keymap so that one instance of a device does not affect
another instance
- it is preferred for drivers to properly set up input_dev->phys to
help userspace locate devices
- drivers should use usb_to_input_id(), or perform endianess conversion,
themselves, otherwise ID is not correct on big-endian boxes
- whitespace and formatting cleanup
Acked-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Fix indent of caiaq in Kconfig to the same level as others.
Just a tidy up.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The last patch for value range checks included a broken merge result.
Now fixed properly.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The kernel build fails, with following error
CC sound/ppc/tumbler.o
sound/ppc/tumbler.c: In function ‘snapper_get_capture_source’:
sound/ppc/tumbler.c:812: error: ‘union <anonymous>’ has no member named ‘value’
sound/ppc/tumbler.c: In function ‘snapper_put_capture_source’:
sound/ppc/tumbler.c:824: error: ‘union <anonymous>’ has no member named ‘enuemerated’
make[2]: *** [sound/ppc/tumbler.o] Error 1
make[1]: *** [sound/ppc] Error 2
make: *** [sound] Error 2
Signed-off-by: Kamalesh Babulal <kamalesh@linx.vnet.ibm.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Volume knob controls with STAC codecs seem to cause problems with some
devices. Volumes change very slowly or silent suddenly. It's likely
due to conflict between the software and the hardware volume knob
setup.
Since we'll have a virtual master control in future, it's safer to
remove this control completely right now.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Show more attributs of volume-knob widgets.
Also don't put empty lines when no connection list is found.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
not sleeping for every codec read/write but doing a short udelay and
a conditional reschedule has cut suspend+resume latency by about 1
second on my T60.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This patch is to add R6xx HDMI audio support. Meanwhile, the device ID
in the previous patch is changed.
I have checked the patch from Herton Ronaldo Krzesinski, it's right as
our spec said. :)
Signed-off-by: Wolke Liu <Wolke.Liu@amd.com>
Signed-off-by: Andrea Zhang <Andrea.Zhang@amd.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Check the value ranges in ctl put callbacks properly (in the rest drivers).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Check the value ranges in ctl put callbacks properly in aoa drivers.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Check the value ranges in ctl put callbacks properly in ak4xxx-adda driver.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Check the value ranges in ctl put callbacks properly in snd-powermac
driver.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Check the value ranges in ctl put callbacks in vxpocket driver.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Clean up ctl callbacks of SE-200PCI driver. Also make sure to check
the value ranges.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Check the value ranges in ctl put callbacks properly in the rest of
PCI drivers.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Check the value ranges in ctl put callbacks properly.
Also fixed some coding style issues around that.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Check the value ranges in ctl put callbacks properly.
Also fixed the wrong access type to enum elements in aureon.c.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Check the value ranges in ctl put callbacks properly so that
invalid values won't be stored or written to registers.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Check value ranges in ctl callbacks properly. This fixes the unexpected
crash due to wrong value assignment.
Also, remove invalid comments in the last patch.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This patch adds ALSA SoC support for TI TLV320AIC3X audio codecs.
The features that are supported:
o Capture/Playback/Bypass.
o 16/20/24/32 bit audio.
o 8k - 96k sample rates.
o codec master only mode
o DAPM.
Signed-off-by: Vladimir Barinov <vbarinov@ru.mvista.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Continue is not needed at the bottom of a loop.
The semantic patch implementing this change is as follows:
@@
@@
for (...;...;...) {
...
if (...) {
...
- continue;
}
}
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added the missing model string for the new support of HP TC T5735.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added the support of HP Thin Client T5735 [0x103c 0x302f] with ALC262 codec.
Signed-off-by: Kailang Yang <kailang@realtek.com.tw>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
When a mic jack is set up as the multiple I/O, it may issue the automute
function wrongly. This patch fixes the wrong automute detection.
Signed-off-by: Jiang Zhe <zhe.jiang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Dell laptops have multiple HP jacks that can be used for multi-channel
outputs. The current auto pincfg handles the speaker as the primary
output and thus cannot handle the multi-channel configuration for such
cases. This patch adds a workaround to fix this issue by swapping the
HP and speaker during multi-channel setup routines.
Signed-off-by: Jiang Zhe <zhe.jiang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Updated dell-m82 model pin config table. The old config doesn't work
with Dell 1210 and co.
Signed-off-by: Jiang Zhe <zhe.jiang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
