The SOF_FW_BOOT_READY_OK fw_state indicates that the boot ready message has
been received and there were no errors found.
The SOF_FW_BOOT_COMPLETE state will be reached after the
snd_sof_dsp_post_fw_run() completes without error.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Paul Olaru <paul.olaru@oss.nxp.com>
Link: https://lore.kernel.org/r/20211223113628.18582-9-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The SOF_FW_CRASHED state is meant to indicate the unfortunate case when the
firmware has crashed after a successful boot.
IPC tx timeout is not treated as indication of a firmware crash as it tends
to happen regularly while the firmware is operational.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Paul Olaru <paul.olaru@oss.nxp.com>
Link: https://lore.kernel.org/r/20211223113628.18582-8-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When snd_sof_dsp_dbg_dump() is called we have an explanatory message to
give some hint on the reason why we have the dump on the caller level.
Pass this message to snd_sof_dsp_dbg_dump() and handle the print according
to the dump rules.
This way we can finally print information on the HDA boot iteration if all
dumps are enabled.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20211223113628.18582-7-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Some platforms use retries during firmware boot to overcome DSP startup
issues.
In these cases we might receive a DSP panic message which should not be
treated as fatal if it happens during boot.
Pass this information to snd_sof_dsp_panic() and omit the panic print if
it is not fatal or the user does not want to see all dumps.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20211223113628.18582-6-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The sof_debug_check_flag() is available for checking flags set in
sof_core_debug.
sof_core_debug can be marked static in core.c
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20211223113628.18582-5-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The sof_debug_check_flag() can be used to check a flag or a combination of
them in sof_core_debug.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20211223113628.18582-4-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
HDA_FW_BOOT_ATTEMPTS is defined in hda.h, do not define it again locally
in hda-loader.c
At the same time correct the indentation for the define in hda.h
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20211223113628.18582-3-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Catch the cases when the stored sdev->dsp_oops_offset and the offset
received via the panic message differs and print a warning, but keep using
the dsp_oops_offset for the oops query.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20211223113628.18582-2-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The Clevo NJ51CU comes either with the ALC293 or the ALC256 codec, but uses
the 0x8686 subproduct id in both cases. The ALC256 codec needs a different
quirk for the headset microphone working and and edditional quirk for sound
working after suspend and resume.
When waking up from s3 suspend the Coef 0x10 is set to 0x0220 instead of
0x0020 on the ALC256 codec. Setting the value manually makes the sound
work again. This patch does this automatically.
[ minor coding style fix by tiwai ]
Signed-off-by: Werner Sembach <wse@tuxedocomputers.com>
Fixes: b5acfe152a ("ALSA: hda/realtek: Add some Clove SSID in the ALC293(ALC1220)")
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211215191646.844644-1-wse@tuxedocomputers.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In the HDAS ACPI scope, the SoundWire may not be the direct child of HDAS.
It needs to go through the ACPI table at max depth of 2 to find the
SoundWire device from HDAS.
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Libin Yang <libin.yang@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20211221010817.23636-3-yung-chuan.liao@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The existing code currently sets a pointer to an ACPI handle before
checking that it's actually a SoundWire controller. This can lead to
issues where the graph walk continues and eventually fails, but the
pointer was set already.
This patch changes the logic so that the information provided to
the caller is set when a controller is found.
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Libin Yang <libin.yang@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20211221010817.23636-2-yung-chuan.liao@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The silent stream stuff recurses back into i915 audio
component .get_power() from the .pin_eld_notify() hook.
On GLK this will deadlock as i915 may already be holding
the relevant modeset locks during .pin_eld_notify() and
the GLK audio vs. CDCLK workaround will try to grab the
same locks from .get_power().
Until someone comes up with a better fix just disable the
silent stream support on GLK.
Cc: stable@vger.kernel.org
Cc: Harsha Priya <harshapriya.n@intel.com>
Cc: Emmanuel Jillela <emmanuel.jillela@intel.com>
Cc: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Cc: Takashi Iwai <tiwai@suse.de>
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/2623
Fixes: 951894cf30 ("ALSA: hda/hdmi: Add Intel silent stream support")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20211222145350.24342-1-ville.syrjala@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is a relatively large set of driver specific changes so it may make
sense to hold off to v5.17, though picking some over might be good.
It's a combination of new device IDs and fixes for various driver
specific things which are all small and of the usual "really bad if
you're running into them" level, especially the Tegra ones.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmHAujcACgkQJNaLcl1U
h9BlCQf/dCcwkh8e80lJwlRhqZUc71ZiXE9gw8aR+9qn+TLabIlNW+lCU/RWGx5h
EXZxBapZ2GbTNf16ZpyTVPfLWUwIZnxOiahigtdSwW97KtfY8oTU5wRdTMmc7NDl
mJy5rqn7sjeoZcXe8NZtX2BmbBRHMq9AhECt56ji6Z7jS2OwPKPYHegA7EFrJ6lX
zBntFWxDkffj2tsfdn7HPLbcILjvm5+3Q8Fu8XfKh1f6qtGKqd19ldcKzJUL2IqR
HaKvMSMQOtDVKCCtFVZ2WMwoZyRQOEmHWjM0I4tKEIVsRrE/VujpUr8TILLenl7R
9LWqe9FFQzwLjsUKZi1+xcMul+o8KA==
=gLlq
-----END PGP SIGNATURE-----
Merge tag 'asoc-fix-v5.16-rc6' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v5.16
This is a relatively large set of driver specific changes so it may make
sense to hold off to v5.17, though picking some over might be good.
It's a combination of new device IDs and fixes for various driver
specific things which are all small and of the usual "really bad if
you're running into them" level, especially the Tegra ones.
Don't use enums for DACL/DACR Signal Invert controls,
and change them into a stereo "DAC Signal Invert Switch" control.
Signed-off-by: Vincent Knecht <vincent.knecht@mailoo.org>
Link: https://lore.kernel.org/r/20211222135403.2991657-1-vincent.knecht@mailoo.org
Signed-off-by: Mark Brown <broonie@kernel.org>
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue
when using hierarchical interrupt domains using "interrupts" property
in the node as this bypasses the hierarchical setup and messes up the
irq chaining.
In preparation for removal of static setup of IRQ resource from DT core
code use platform_get_irq().
While at it also drop "r_irq" member from struct bcm_i2s_priv as there
are no users of it.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20211221170100.27423-3-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue
when using hierarchical interrupt domains using "interrupts" property
in the node as this bypasses the hierarchical setup and messes up the
irq chaining.
In preparation for removal of static setup of IRQ resource from DT core
code use platform_get_irq().
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211221170100.27423-2-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This code frees "graph" and then dereferences to save the error code.
Save the error code first and then use gotos to unwind the allocation.
Fixes: 59716aa3f9 ("ASoC: qdsp6: Fix an IS_ERR() vs NULL bug")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20211217150007.GB16611@kili
Signed-off-by: Mark Brown <broonie@kernel.org>
cppcheck warning:
sound/soc/sof/amd/acp.c:222:9: warning: Identical condition and return
expression 'ret', return value is always 0
[identicalConditionAfterEarlyExit]
return ret;
^
sound/soc/sof/amd/acp.c:213:6: note: If condition 'ret' is true, the
function will return/exit
if (ret)
^
sound/soc/sof/amd/acp.c:222:9: note: Returning identical expression 'ret'
return ret;
^
Just return 0; on success.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Ajit Kumar Pandey <AjitKumar.Pandey@amd.com>
Link: https://lore.kernel.org/r/20211221165802.236843-1-AjitKumar.Pandey@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
SOF machines support different codec end points and hence required
different topologies configuration. Update tplg filename in machine
struct to load different topology files for SOF machines.
Signed-off-by: Ajit Kumar Pandey <AjitKumar.Pandey@amd.com>
Reviewed-by: Curtis Malainey <curtis@malainey.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20211221161814.236318-3-AjitKumar.Pandey@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We need to support sof audio on different variants of Google boards.
Add new entry in dmi table to enable SOF flag on Google chrome boards.
Also add newer machines to sof_machines list with codecs and amps acpi
id check to register sof sound cards on different variants.
Signed-off-by: Ajit Kumar Pandey <AjitKumar.Pandey@amd.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@intel.com>
Link: https://lore.kernel.org/r/20211221161814.236318-2-AjitKumar.Pandey@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>:
This patch-set tries to use dev_err_probe() helper function
instead of manual dev_err() code.
I hope ASoC will be more clean code by this patch-set.
Eliminates error messages if snd_soc_register_card() failed. Kernel
emits messages if device probe error anyway.
This is mainly for removing the following error messages during boot.
>>> snd_soc_register_card fail -517
Signed-off-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20211220093408.207206-1-tzungbi@google.com
Signed-off-by: Mark Brown <broonie@kernel.org>
mt8195_cg_patch is used to reset the default value of audio cg, so the
register value could be consistent with CCF reference count.
Nevertheless, AUDIO_TOP_CON1[1:0] is used to control an internal mux,
and it's expected to keep the default value 0.
This patch corrects the default value in case an unexpected behavior
happens in the future.
Fixes: 6746cc8582 ("ASoC: mediatek: mt8195: add platform driver")
Signed-off-by: Trevor Wu <trevor.wu@mediatek.com>
Link: https://lore.kernel.org/r/20211216022424.28470-1-trevor.wu@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Cezary Rojewski <cezary.rojewski@intel.com>:
Set is made of one fix for dma-transfer so that result of
dmaengine_submit() is tested before moving on, and few cleanups:
- two non-impactful, where catpt_component_open() layout gets improved
slightly as well as relocation of couple of locals found in
PCM-functions so that they look more cohesive
- no need to expose catpt-driver board-matching information globally.
Most fields are not by it and it's the sole user of haswell_machines
table. By having them locally it is clear what is actually being used
Cezary Rojewski (5):
ASoC: Intel: catpt: Test dmaengine_submit() result before moving on
ASoC: Intel: catpt: Reduce size of catpt_component_open()
ASoC: Intel: catpt: Streamline locals declaration for PCM-functions
ASoC: Intel: catpt: Drop SND_SOC_ACPI_INTEL_MATCH dependency
ASoC: Intel: Drop legacy HSW/BDW board-match information
include/sound/soc-acpi-intel-match.h | 1 -
sound/soc/intel/Kconfig | 2 +-
sound/soc/intel/catpt/device.c | 33 +++++++++++++++--
sound/soc/intel/catpt/dsp.c | 14 ++++++-
sound/soc/intel/catpt/pcm.c | 37 +++++++++----------
.../common/soc-acpi-intel-hsw-bdw-match.c | 16 --------
6 files changed, 61 insertions(+), 42 deletions(-)
--
2.25.1
Merge series from Dmitry Osipenko <digetx@gmail.com>:
This series revives Tegra20 S/PDIF driver which was upstreamed long time
ago, but never was used. It also turns Tegra DRM HDMI driver into HDMI
audio CODEC provider. Finally, HDMI audio is enabled in device-trees.
For now the audio is enable only for Acer A500 tablet and Toshiba AC100
netbook because they're already supported by upstream, later on ASUS TF101
tablet will join them.
I based S/PDIF patches on Arnd's Bergmann patch from a separate series [1]
that removes obsolete slave_id. This eases merging of the patches by
removing the merge conflict. This is a note for Mark Brown.
I also based this series on top of power management series [2]. I.e. [2]
should be applied first, otherwise "Add S/PDIF node to Tegra20 device-tree"
patch should have merge conflict. This is a note for Thierry.
[1] https://patchwork.ozlabs.org/project/linux-tegra/list/?series=273312
[2] https://patchwork.ozlabs.org/project/linux-tegra/list/?series=274534
Changelog:
v4: - Added patches that update multi_v7_defconfig with the enabled S/PDIF
and APB DMA drivers.
v3: - Renamed S/PDIF device-tree clocks as was suggested by Rob Herring.
- Added r-bs and acks that were given by Rob Herring to v2.
v2: - Corrected I2S yaml problem that was reported by the DT bot for v1
by removing the non-existent required clock-names property.
- Removed assigned-clocks property from S/PDIF yaml since this property
is now inherited from the clocks property.
- Reordered the "tegra20: spdif: Set FIFO trigger level" patch, making
it the first sound/soc patch in the series, like it was suggested by
Mark Brown in the comment to v1. Also reworded commit message of this
patch to *not* make it looks like it should be backported to stable
kernels.
Arnd Bergmann (1):
ASoC: tegra20-spdif: stop setting slave_id
Dmitry Osipenko (21):
ASoC: dt-bindings: Add binding for Tegra20 S/PDIF
ASoC: dt-bindings: tegra20-i2s: Convert to schema
ASoC: dt-bindings: tegra20-i2s: Document new nvidia,fixed-parent-rate
property
dt-bindings: host1x: Document optional HDMI sound-dai-cells
ASoC: tegra20: spdif: Set FIFO trigger level
ASoC: tegra20: spdif: Support device-tree
ASoC: tegra20: spdif: Improve driver's code
ASoC: tegra20: spdif: Use more resource-managed helpers
ASoC: tegra20: spdif: Reset hardware
ASoC: tegra20: spdif: Support system suspend
ASoC: tegra20: spdif: Filter out unsupported rates
ASoC: tegra20: i2s: Filter out unsupported rates
drm/tegra: hdmi: Unwind tegra_hdmi_init() errors
drm/tegra: hdmi: Register audio CODEC on Tegra20
ARM: tegra_defconfig: Enable S/PDIF driver
ARM: config: multi v7: Enable NVIDIA Tegra20 S/PDIF driver
ARM: config: multi v7: Enable NVIDIA Tegra20 APB DMA driver
ARM: tegra: Add S/PDIF node to Tegra20 device-tree
ARM: tegra: Add HDMI audio graph to Tegra20 device-tree
ARM: tegra: acer-a500: Enable S/PDIF and HDMI audio
ARM: tegra: paz00: Enable S/PDIF and HDMI audio
.../display/tegra/nvidia,tegra20-host1x.txt | 1 +
.../bindings/sound/nvidia,tegra20-i2s.txt | 30 ---
.../bindings/sound/nvidia,tegra20-i2s.yaml | 77 +++++++
.../bindings/sound/nvidia,tegra20-spdif.yaml | 85 ++++++++
.../boot/dts/tegra20-acer-a500-picasso.dts | 8 +
arch/arm/boot/dts/tegra20-paz00.dts | 8 +
arch/arm/boot/dts/tegra20.dtsi | 40 +++-
arch/arm/configs/multi_v7_defconfig | 2 +
arch/arm/configs/tegra_defconfig | 1 +
drivers/gpu/drm/tegra/Kconfig | 3 +
drivers/gpu/drm/tegra/hdmi.c | 168 +++++++++++++--
sound/soc/tegra/tegra20_i2s.c | 49 +++++
sound/soc/tegra/tegra20_spdif.c | 197 ++++++++++++------
sound/soc/tegra/tegra20_spdif.h | 1 +
sound/soc/tegra/tegra_pcm.c | 6 +
sound/soc/tegra/tegra_pcm.h | 1 +
16 files changed, 574 insertions(+), 103 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/sound/nvidia,tegra20-i2s.txt
create mode 100644 Documentation/devicetree/bindings/sound/nvidia,tegra20-i2s.yaml
create mode 100644 Documentation/devicetree/bindings/sound/nvidia,tegra20-spdif.yaml
--
2.33.1
Merge series from Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>:
Guennadi spotted inconsistencies with our 'const' handling, Ajit Kumar
flagged a missing check for a null pointer and we missed the
definition of debug zones.
Merge series from Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>:
None of the SOF platforms support INFO_RESUME, and rely on the
indirect path used by the ALSA core with the prepare and TRIGGER_START
steps.
Let's remove the left-over dead code.
The return value of pm_runtime_resume_and_get() needs to be checked to
avoid a usage count imbalance in the error case. This fix is basically
the same as 92c959bae2 ("reset: renesas: Fix Runtime PM usage"),
and the last step before pm_runtime_resume_and_get() can be annotated
as __must_check.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/9fed506d-b780-55cd-45a4-9bd2407c910f@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
After calling dmaengine_submit(), the submitted transfer descriptor
belongs to the DMA engine. Pointer to that descriptor may no longer be
valid after the call and should be tested before awaiting transfer
completion.
Reported-by: Kevin Tian <kevin.tian@intel.com>
Suggested-by: Dave Jiang <dave.jiang@intel.com>
Fixes: 4fac9b31d0 ("ASoC: Intel: Add catpt base members")
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20211216115743.2130622-2-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Support new nvidia,fixed-parent-rate device-tree property which instructs
I2S that board wants parent clock rate to stay at a fixed rate. This allows
to play audio over S/PDIF and I2S simultaneously. The root of the problem
is that audio components on Tegra share the same audio PLL, and thus, only
a subset of rates can be supported if we want to play audio simultaneously.
Filter out audio rates that don't match parent clock rate if device-tree
has the nvidia,fixed-parent-rate property.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20211204143725.31646-14-digetx@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
SPDIF and other SoC components share audio PLL on Tegra, thus only one
component may set the desired base clock rate. This creates problem for
HDMI audio because it uses SPDIF and audio may not work if SPDIF's clock
doesn't exactly match standard audio rate since some receivers may reject
audio in that case. Filter out audio rates which SPDIF output can't
support, assuming that other components won't change rate at runtime.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20211204143725.31646-13-digetx@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Support system suspend by enforcing runtime PM suspend/resume.
Now there is no doubt that h/w is indeed stopped during suspend
and that h/w state will be properly restored after resume.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20211204143725.31646-12-digetx@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Reset S/PDIF controller on runtime PM suspend/resume to ensure that we
always have a consistent hardware state.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20211204143725.31646-11-digetx@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use resource-managed helpers to make code cleaner. Driver's remove callback
isn't needed anymore since driver is completely resource-managed now.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20211204143725.31646-10-digetx@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
- Clean up whitespaces, defines and variables.
- Remove obsolete code.
- Adhere to upstream coding style.
- Don't override returned error code.
- Replace pr_err with dev_err.
No functional changes are made by this patch. This is a minor code's
refactoring that will ease further maintenance of the driver.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20211204143725.31646-9-digetx@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Tegra20 S/PDIF driver was added in a pre-DT era and was never used since
that time. Revive driver by adding device-tree support.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20211204143725.31646-8-digetx@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
FIFO trigger level must be not less than the size of DMA burst, otherwise
audio will be played x4 faster that it should be because part of the DMA
data will be dropped on FIFO input buffer overflow.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20211204143725.31646-6-digetx@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Tag for dmaengine slave_id removal topic branch which should be merged
into v5.17
-----BEGIN PGP SIGNATURE-----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=Mpf8
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmG8cOYACgkQJNaLcl1U
h9D+Wgf+PdDgmb/kBATZNCfSa13y0A18EVC0ETrCn7EBQt6UbyU5Zx/rVOe8Sjw+
d/kuqc0WCV3UrSdnZHh1pYpn/eqRh6KJCufMJFQiYAEwjJi5TQ5eYDHf7sd0oEI8
NOkTJbl26UImAsnsHcC35moHyTH2U8sKoEeva5i/MIXxBpn+3cIWnmjUi7ZUEzLu
qmZDPEYHVRklcbFEWI7oehb68hJlTHz2PY9ARM+sTUica9owlTiaGRD2WX+Wtc5G
fx0rWoIiFUGnW2qoRBX7yNOBKvzmT6m+pqPMQ/LAjE1Xa4Cb0e87fm33b1QFhuEk
CYFHAAzKem/3GskXlR57fY4p8CvJmQ==
=6fXc
-----END PGP SIGNATURE-----
Merge tag 'dmaengine_topic_slave_id_removal_5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine into v4_20211204_digetx_support_hdmi_audio_on_nvidia_tegra20
dmaengine_topic_slave_id_removal_5.17
Tag for dmaengine slave_id removal topic branch which should be merged
into v5.17
SND_SOC_SOF_DEVELOPER_SUPPORT contains options affecting how the built
SOF driver stack will behave, enables debug options and other features.
These options have no meaning if the SND_SOC_SOF is not even enabled.
If we have SOF client options under developer_support and debug they can
be selected to be built even without the core, but they do need symbols
from the core (the sof-client API) which can result build failure.
In Kconfig we can have
SND_SOC_SOF_TOPLEVEL=y
SND_SOC_SOF_DEBUG_IPC_FLOOD_TEST=y
for example, which will make the flood client to be built, but the SOF core
is not as SND_SOC_SOF is not selected.
Reviewed-by: Paul Olaru <paul.olaru@oss.nxp.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20211216230350.343857-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When pcm stream is stopped "substream->runtime" pointer will be set
to NULL by ALSA core. In case host received an ipc msg from firmware
of type IPC_STREAM_POSITION after pcm stream is stopped, there will
be kernel NULL pointer exception in ipc_period_elapsed(). This patch
fixes it by adding NULL pointer check for "substream->runtime".
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Ajit Kumar Pandey <AjitKumar.Pandey@amd.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20211216232422.345164-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The SOF driver removed the support for INFO_RESUME in the commit
"ASoC: SOF: pcm: do not add SNDRV_PCM_INFO_RESUME to runtime hw info".
And resuming is handled by the ALSA core with the .prepare and
.trigger_start stages. So, remove handling of RESUME trigger in the
component driver trigger op. So, remove handling the RESUME trigger in
the platform trigger op for HDA platforms.
Reviewed-by: Kai Vehmanen <kai.vehmanen@intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20211216231628.344687-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The SOF driver removed the support for INFO_RESUME in the commit
"ASoC: SOF: pcm: do not add SNDRV_PCM_INFO_RESUME to runtime hw info".
And resuming is handled by the ALSA core with the .prepare and
.trigger_start stages. So, remove handling of RESUME trigger in the
HDA DAI BE trigger op.
Reviewed-by: Kai Vehmanen <kai.vehmanen@intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20211216231628.344687-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The SOF driver removed the support for INFO_RESUME in the commit
"ASoC: SOF: pcm: do not add SNDRV_PCM_INFO_RESUME to runtime hw info".
And resuming is handled by the ALSA core with the .prepare and
.trigger_start stages. So, remove handling of RESUME trigger in the
component driver trigger op.
Reviewed-by: Kai Vehmanen <kai.vehmanen@intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20211216231628.344687-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This field is no longer set from any driver now, so remove the
last references as well.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20211122222203.4103644-3-arnd@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The DMA resource is never set up anywhere, and passing this as slave_id
has not been the proper procedure in a long time.
As a preparation for removing all slave_id references from the ALSA code,
remove this one.
According to Dmitry Osipenko, this driver has never been used and
the mechanism for configuring DMA would not work as it is implemented,
so this part will get rewritten when the driver gets put into use
again in the future.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20211122222203.4103644-2-arnd@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Merge series from Ranjani Sridharan <ranjani.sridharan@linux.intel.com>:
This set of patches deals with modifications to the signature of kcontrol
get/set data functions to make them more intuitive. The last patch deals
with initializing the binary control data size after boot up.
on i386 or x86_64:
when # CONFIG_ACPI is not set,
so SND_SOC_ACPI is not set:
WARNING: unmet direct dependencies detected for SND_AMD_ACP_CONFIG
Depends on [n]: SOUND [=y] && !UML && SND [=y] && SND_SOC [=y] &&
SND_SOC_ACPI [=n]
Selected by [y]:
- SND_SOC_AMD_ACP_COMMON [=y] && SOUND [=y] && !UML && SND [=y] &&
SND_SOC [=y] && X86 [=y] && PCI [=y]
This problem is due to the unconditional selection of
SND_AMD_ACP_CONFIG in other options. Using 'depends on' solved an
initial problem but exposed another, let's use select instead.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Fixes: d9b994cd76 ('ASoC: AMD: acp-config: fix missing dependency on SND_SOC_ACPI')
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@intel.com>
Reviewed-by: Ajit Kumar Pandey <AjitKumar.Pandey@amd.com>
Link: https://lore.kernel.org/r/20211215163511.151286-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Read back the control data from the DSP to initialize the control data
size to match that of the data in the DSP. This is particularly useful
for volatile read-only kcontrols in static pipelines.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20211215180404.53254-9-ranjani.sridharan@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The SOF_CTRL_TYPE_VALUE_COMP_* type is not used by the firmware nor in the
kernel side.
It is also not clear what action should be taken for such type.
With this in mind:
The correct ipc_cmd can be selected based on the `ctrl_cmd` and the `set`
parameters:
if the ctrl_cmd is SOF_CTRL_CMD_BINARY then SOF_CTRL_TYPE_DATA_*
otherwise SOF_CTRL_TYPE_VALUE_CHAN_*.
The SET or GET direction can be selected with the use of `set` parameter.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20211215180404.53254-8-ranjani.sridharan@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The component type is not used in firmware nor in the kernel currently and
it is not even clear how it should be handled.
Do not even try to handle it to avoid errors.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20211215180404.53254-7-ranjani.sridharan@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no need to use two variables to store and check the same
information, the scontrol->cmd is the same as scontrol->control_data->cmd.
Drop the former one and when it is needed, access the cmd from the
control_data.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20211215180404.53254-6-ranjani.sridharan@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The scontrol->control_data->cmd has been configured during initialization
to the correct sof_ipc_ctrl_cmd.
No need to pass duplicated information, let's use the already available
one via scontrol.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20211215180404.53254-5-ranjani.sridharan@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the scontrol->control_data->cmd early to the same as scontrol->cmd.
This is a preparatory patch to remove the ctrl_cmd parameter for the
snd_sof_ipc_set_get_comp_data() function.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20211215180404.53254-4-ranjani.sridharan@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The correct ipc_cmd can be selected based on the `ctrl_cmd` and the `set`
parameters:
if the ctrl_cmd is SOF_CTRL_CMD_BINARY then SOF_IPC_COMP_*_DATA
otherwise SOF_IPC_COMP_*_VALUE.
The SET or GET direction can be selected with the use of `set` parameter.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20211215180404.53254-3-ranjani.sridharan@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Rename the send parameter to set in snd_sof_ipc_set_get_comp_data() and
sof_set_get_large_ctrl_data() to be more aligned with the function name.
No functional change.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20211215180404.53254-2-ranjani.sridharan@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The return value of device_property_read_u32_array() is not always 0.
To catch the exception in case that devm_kzalloc failed and the
rt5663->imp_table was NULL, which caused the failure of
device_property_read_u32_array.
Fixes: 450f0f6a8f ("ASoC: rt5663: Add the manual offset field to compensate the DC offset")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Link: https://lore.kernel.org/r/20211215031550.70702-1-jiasheng@iscas.ac.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
Similar with commit 8a49cd11e6 ("ASoC: SOF: ACPI: avoid reverse
module dependency") we will be having hardware specific drivers that
link against a common "helper" framework.
sof-of-dev.c becomes a library with the interface defined in the newly
created file sof-of-dev.h.
This is the final step started with Kconfig simplification in
commit 7548a391c5 ("ASoC: SOF: i.MX: simplify Kconfig")
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Reviewed-by: Paul Olaru <paul.olaru@oss.nxp.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20211215085703.137414-1-daniel.baluta@oss.nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There is a HP ProBook which using ALC236 codec and need the
ALC236_FIXUP_HP_MUTE_LED_MICMUTE_VREF quirk to make mute LED and
micmute LED work.
Signed-off-by: Jeremy Szu <jeremy.szu@canonical.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211214164156.49711-1-jeremy.szu@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Merge series from Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>:
We've been adding a 'deep buffer' PCM device to several SOF topologies
in order to reduce power consumption. The typical use-case would be
music playback over a headset: this additional PCM device provides
more buffering and longer latencies, leaving the rest of the system
sleep for longer periods. Notifications and 'regular' low-latency
audio playback would still use the 'normal' PCM device and be mixed
with the 'deep buffer' before rendering on the headphone endpoint. The
tentative direction would be to expose this alternate device to
PulseAudio/PipeWire/CRAS via the UCM SectionModifier definitions.
That seemed a straightforward topology change until our automated
validation stress tests started reporting issues on SoundWire
platforms, when e.g. two START triggers might be send and conversely
the STOP trigger is never sent. The SoundWire stream state management
flagged inconsistent states when the two 'normal' and 'deep buffer'
devices are used concurrently with rapid play/stop/pause monkey
testing.
Looking at the soc-pcm.c code, it seems that the BE state
management needs a lot of love.
a) there is no consistent protection for the BE state. In some parts
of the code, the state updates are protected by a spinlock but in the
trigger they are not. When we open/play/close the two PCM devices in
stress tests, we end-up testing a state that is being modified. That
can't be good.
b) there is a conceptual deadlock: on stop we check the FE states to
see if a shared BE can be stopped, but since we trigger the BE first
the FE states have not been modified yet, so the TRIGGER_STOP is never
sent.
This patchset suggests the removal of the dedicated 'dpcm_lock' and
follows the design suggested by Takashi Iwai. By default the
protection relies on the 'pcm_mutex', except for the FE and BE
triggers where the mutex cannot be used. In this case, the FE PCM
lock is used instead. In the cases where a BE is added/removed, the
pcm_mutex and FE PCM lock are both taken. In addition, the BE PCM
lock is used to serialize access to a shared BE.
With these patches I am able to run our entire validation suite
without any issues with this new 'deep buffer' topology, and no
regressions on existing solutions [1]. The tests were reproduced by
Bard Liao for SoundWire devices.
One might ask 'how come we didn't see this earlier'? The answer is
probably that the .trigger callbacks in most implementations seems to
perform DAPM operations, and sending the triggers multiple times is
not an issue. In the case of SoundWire, we do use the .trigger
callback to reconfigure the bus using the 'bank switch' mechanism. It
could be acceptable to tolerate a trigger multiple times, but the
deadlock on stop cannot be fixed at the SoundWire level alone.
Opens:
1) The issues reported by Nvidia on the RFCv3 may or may not be
present. We'd need test results to make sure the locking update does
not introduce a regression on Tegra.
2) There are other reports of kernel oopses [2] that seem related to
the lack of protection. I'd be good to confirm if this patchset solve
these problems as well.
[1] https://github.com/thesofproject/linux/pull/3146
[2] https://lore.kernel.org/alsa-devel/002f01d7b4f5$c030f4a0$4092dde0$@samsung.com/
changes since RFCv3:
Used two patches from Takashi. We now use the pcm_mutex, the FE stream
lock when adding and deleting a BE, and the BE stream lock to handle
concurrency between streams using the same BE.
Added a patch to use GFP_ATOMIC for the DPCM structure.
Fixed PAUSE_RELEASE transition (GitHub comment from Kai Vehmanen)
changes since RFCv2:
Removal of dpcm_lock to use FE PCM locks (credits to Takashi Iwai for
the suggestion). The FE PCM lock is now used before each use of
for_each_dpcm_be() - with the exception of the trigger where the lock
is already taken. This change is also applied in drivers which make
use of this loop (compress, SH, FSL).
Addition of BE PCM lock to deal with mutual exclusion between triggers
for the same BE.
Alignment of the BE atomicity on the FE on connections, this is
required to avoid sleeping in atomic context.
Additional cleanups (indentation, static functions)
changes since RFC v1:
Removed unused function
Removed exported symbols only used in soc-pcm.c, used static instead
Use a mutex instead of a spinlock
Protect all for_each_dpcm_be() loops
Fix bugs introduced in the refcount
Pierre-Louis Bossart (4):
ASoC: soc-pcm: use GFP_ATOMIC for dpcm structure
ASoC: soc-pcm: align BE 'atomicity' with that of the FE
ASoC: soc-pcm: test refcount before triggering
ASoC: soc-pcm: fix BE handling of PAUSE_RELEASE
Takashi Iwai (2):
ASoC: soc-pcm: Fix and cleanup DPCM locking
ASoC: soc-pcm: serialize BE triggers
include/sound/soc-dpcm.h | 2 +
include/sound/soc.h | 2 -
sound/soc/soc-core.c | 1 -
sound/soc/soc-pcm.c | 351 +++++++++++++++++++++++++++------------
4 files changed, 246 insertions(+), 110 deletions(-)
--
2.25.1
Distinguish which headset codec is on the board by codec_dai->name
instead of card->name.
It fixes the crash of being unable to handle kernel paging requests
at virtual address ADDR by initializing the correct audio codec on
the board.
Call stack of the crash:
```
Unable to handle kernel paging request at virtual address ...
...
Call trace:
rt5682_set_component_pll+0xcc/0xb78 [snd_soc_rt5682]
snd_soc_component_set_pll+0x90/0x154
snd_soc_dai_set_pll+0xf4/0x1ac
sc7180_snd_startup+0x268/0x3c0 [snd_soc_sc7180]
snd_soc_link_startup+0xa4/0x180
soc_pcm_open+0x35c/0x15c8
snd_pcm_open_substream+0xa90/0x13b0
snd_pcm_open+0x1a4/0x55c
snd_pcm_capture_open+0x7c/0xe8
snd_open+0x2b8/0x2e4
chrdev_open+0x364/0x3d4
do_dentry_open+0x66c/0xc58
vfs_open+0x7c/0x8c
path_openat+0x108c/0x2bbc
do_filp_open+0x15c/0x258
do_sys_open+0x278/0x62c
__arm64_compat_sys_openat+0x9c/0xb0
...
```
Fixes: 425c5fce8a ("ASoC: qcom: Add support for ALC5682I-VS codec")
Signed-off-by: Judy Hsiao <judyhsiao@chromium.org>
Link: https://lore.kernel.org/r/20211214022509.1288245-1-judyhsiao@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
A BE connected to more than one FE, e.g. in a mixer case, can go
through the following transitions.
play FE1 -> BE state is START
pause FE1 -> BE state is PAUSED
play FE2 -> BE state is START
stop FE2 -> BE state is STOP (see note [1] below)
release FE1 -> BE state is START
stop FE1 -> BE state is STOP
play FE1 -> BE state is START
pause FE1 -> BE state is PAUSED
play FE2 -> BE state is START
release FE1 -> BE state is START
stop FE2 -> BE state is START
stop FE1 -> BE state is STOP
play FE1 -> BE state is START
play FE2 -> BE state is START (no change)
pause FE1 -> BE state is START (no change)
pause FE2 -> BE state is PAUSED
release FE1 -> BE state is START
release FE2 -> BE state is START (no change)
stop FE1 -> BE state is START (no change)
stop FE2 -> BE state is STOP
The existing code for PAUSE_RELEASE only allows for the case where the
BE is paused, which clearly would not work in the sequences above.
Extend the allowed states to restart the BE when PAUSE_RELEASE is
received, and increase the refcount if the BE is already in START.
[1] the existing logic does not move the BE state back to PAUSED when
the FE2 is stopped. This patch does not change the logic; it would be
painful to keep a history of changes on the FE side, the state machine
is already rather complicated with transitions based on the last BE
state and the trigger type.
Reported-by: Bard Liao <bard.liao@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20211207173745.15850-7-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
On start/pause_release/resume, when more than one FE is connected to
the same BE, it's possible that the trigger is sent more than
once. This is not desirable, we only want to trigger a BE once, which
is straightforward to implement with a refcount.
For stop/pause/suspend, the problem is more complicated: the check
implemented in snd_soc_dpcm_can_be_free_stop() may fail due to a
conceptual deadlock when we trigger the BE before the FE. In this
case, the FE states have not yet changed, so there are corner cases
where the TRIGGER_STOP is never sent - the dual case of start where
multiple triggers might be sent.
This patch suggests an unconditional trigger in all cases, without
checking the FE states, using a refcount protected by the BE PCM
stream lock.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20211207173745.15850-6-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When more than one FE is connected to a BE, e.g. in a mixing use case,
the BE can be triggered multiple times when the FE are opened/started
concurrently. This race condition is problematic in the case of
SoundWire BE dailinks, and this is not desirable in a general
case.
This patch relies on the existing BE PCM lock, which takes atomicity into
account. The locking model assumes that all interactions start with
the FE, so that there is no deadlock between FE and BE locks.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
[test, checkpatch fix and clarification of commit message by plbossart]
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20211207173745.15850-5-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The existing locking for DPCM has several issues
a) a confusing mix of card->mutex and card->pcm_mutex.
b) a dpcm_lock spinlock added inconsistently and on paths that could
be recursively taken. The use of irqsave/irqrestore was also overkill.
The suggested model is:
1) The pcm_mutex is the top-most protection of BE links in the FE. The
pcm_mutex is applied always on either the top PCM callbacks or the
external call from DAPM, not taken in the internal functions.
2) the FE stream lock is taken in higher levels before invoking
dpcm_be_dai_trigger()
3) when adding and deleting a BE, both the pcm_mutex and FE stream
lock are taken.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
[clarification of commit message by plbossart]
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20211207173745.15850-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Since the flow for DPCM is based on taking a lock for the FE first, we
need to make sure during the connection between a BE and an FE that
they both use the same 'atomicity', otherwise we may sleep in atomic
context.
If the FE is nonatomic, this patch forces the BE to be nonatomic as
well. That should have no negative impact since the BE 'inherits' the
FE properties.
However, if the FE is atomic and the BE is not, then the configuration
is flagged as invalid.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
[ removed FE stream lock by tiwai ]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20211207173745.15850-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We allocate a structure in dpcm_be_connect(), which may be called in
atomic context. Using GFP_KERNEL is not quite right, we have to use
GFP_ATOMIC to prevent the allocator from sleeping.
Suggested-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20211207173745.15850-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The out-of-tree vendor driver uses the following approach to set the
AIU_I2S_MISC register:
1) write AIU_MEM_I2S_START_PTR and AIU_MEM_I2S_RD_PTR
2) configure AIU_I2S_MUTE_SWAP[15:0]
3) write AIU_MEM_I2S_END_PTR
4) set AIU_I2S_MISC[2] to 1 (documented as: "put I2S interface in hold
mode")
5) set AIU_I2S_MISC[4] to 1 (depending on the driver revision it always
stays at 1 while for older drivers this bit is unset in step 4)
6) set AIU_I2S_MISC[2] to 0
7) write AIU_MEM_I2S_MASKS
8) toggle AIU_MEM_I2S_CONTROL[0]
9) toggle AIU_MEM_I2S_BUF_CNTL[0]
Move setting the AIU_I2S_MISC[2] bit to aiu_fifo_i2s_hw_params() so it
resembles the flow in the vendor kernel more closely. While here also
configure AIU_I2S_MISC[4] (documented as: "force each audio data to
left or right according to the bit attached with the audio data")
similar to how the vendor driver does this. This fixes the infamous and
long-standing "machine gun noise" issue (a buffer underrun issue).
Fixes: 6ae9ca9ce9 ("ASoC: meson: aiu: add i2s and spdif support")
Reported-by: Christian Hewitt <christianshewitt@gmail.com>
Reported-by: Geraldo Nascimento <geraldogabriel@gmail.com>
Tested-by: Christian Hewitt <christianshewitt@gmail.com>
Tested-by: Geraldo Nascimento <geraldogabriel@gmail.com>
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Cc: stable@vger.kernel.org
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20211206210804.2512999-3-martin.blumenstingl@googlemail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The FIFO registers which take an DMA-able address are only 32-bit wide
on AIU. Add dma_coerce_mask_and_coherent() to make the DMA core aware of
this limitation.
Fixes: 6ae9ca9ce9 ("ASoC: meson: aiu: add i2s and spdif support")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20211206210804.2512999-2-martin.blumenstingl@googlemail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Although the codec advertises support for 176.4 and 192 ksps, without
this fix setting those sample rates fails with EINVAL at hw_params time.
Signed-off-by: Martin Povišer <povik@protonmail.com>
Link: https://lore.kernel.org/r/20211206224529.74656-1-povik@protonmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Some powers were changed during the jack insert detection
and clk's enable/disable in CCF.
If in parallel, the influence has a chance to detect
the wrong jack type, so add a lock.
Signed-off-by: Derek Fang <derek.fang@realtek.com>
Link: https://lore.kernel.org/r/20211214105033.471-1-derek.fang@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Stephan Gerhold <stephan@gerhold.net>:
This series makes it possible to route audio through the combined
audio/modem DSP on MSM8916/APQ8016 devices instead of bypassing it using
the LPASS drivers. This is necessary to support certain functionality such
as voice call audio. See PATCH 4/5 for details.
Also, qcom,apq8016-sbc.txt is converted to DT schema by adding it to the
existing qcom,sm8250.yaml. The bindings are similar enough that it is easier
to share a single schema instead of duplicating everything into multiple ones.
Fix the following sparse warning: (new ones prefixed by >>)
>> sound/soc/mediatek/mt8192/mt8192-mt6359-rt1015-rt5682.c:370:33:
sparse: sparse: incorrect type in argument 3 (different base types)
sound/soc/mediatek/mt8192/mt8192-mt6359-rt1015-rt5682.c:370:33: sparse:
expected unsigned int to
sound/soc/mediatek/mt8192/mt8192-mt6359-rt1015-rt5682.c:370:33: sparse:
got restricted snd_pcm_format_t [usertype]
Correct discription of format, use S32_LE and S24_LE to distinguish the
different 32bit.
Signed-off-by: Jiaxin Yu <jiaxin.yu@mediatek.com>
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20211209073224.21793-1-jiaxin.yu@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The only usage of sof_probe_compr_ops is to assign its address to the
cops field in the snd_soc_dai_driver struct (in
sound/soc/sof/intel/hda-dai.c). Make it const to allow the compiler to
put it in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Link: https://lore.kernel.org/r/20211204203220.54712-1-rikard.falkeborn@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In SOF OF device, pm_runtime_put_autosuspend() is not
matching any pm_runtime_get_sync().
This is imbalanced for PM runtime.
Also, for consistency we call pm_runtime_mark_last_busy()
before enabling PM runtime.
1. Remove pm_runtime_put_autosuspend() in probe_complete
2. Reorder PM runtime calls int probe_complete
Signed-off-by: Allen-KH Cheng <Allen-KH.Cheng@mediatek.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Reviewed-by: Paul Olaru <paul.olaru@oss.nxp.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Link: https://lore.kernel.org/r/20211209200830.145005-1-daniel.baluta@oss.nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Adds a new "alc285-hp-amp-init" model that can be used to apply the ALC285
HP speaker amplifier initialization fixup to devices that are not already
known by passing "hda_model=alc285-hp-amp-init" to the
snd-sof-intel-hda-common module or "model=alc285-hp-amp-init" to the
snd-hda-intel module, depending on which is being used.
Signed-off-by: Bradley Scott <bscott@teksavvy.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211213162246.506838-1-bscott@teksavvy.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HP ZBook 15 G6 (SSID 103c:860f) needs the same speaker amplifier
initialization as used on several other HP laptops using ALC285.
Signed-off-by: Bradley Scott <Bradley.Scott@zebra.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211213154938.503201-1-Bradley.Scott@zebra.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The apq8016-sbc-sndcard is designed to be used with the LPASS drivers
(bypassing the combined audio/modem DSP in MSM8916/APQ8016).
Make it possible to use QDSP6 audio instead for the msm8916-qdsp6-sndcard.
This only requires adding some additional hooks that set up the DPCM
backends correctly. Similar code is already used in drivers for newer
SoCs such as apq8096.c, sdm845.c and sm8250.c.
A slightly different initialization sequence is used for the apq8016-sbc
and msm8916-qdsp6 sound card by defining the apq8016_sbc_add_ops()
function as device match data.
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20211202145505.58852-6-stephan@gerhold.net
Signed-off-by: Mark Brown <broonie@kernel.org>
Explain why JasperLake is exposed in cnl.c instead of icl.c
No functionality change.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20211207193947.71080-8-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The existing code does not use the 'host_dma_id', 'link_dma_id',
'host_bps' fields remove them.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20211207193947.71080-7-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The code inherited from the Skylake driver does not seem to follow any
known hardware recommendations.
The only two recommended options are
a) use DPIB registers if VC1 traffic is not allowed
b) use DPIB DDR update if VC1 traffic is used
In all of SOF-based updated, VC1 is not supported so we can 'safely'
move to using DPIB registers only.
This patch keeps the legacy code, in case there was an undocumented
issue lost to history, and adds the DPIB DDR update for additional
debug.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20211207193947.71080-6-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The existing code is inconsistent, we should only enable DPIB if the
'use_posbuf' field is true.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20211207193947.71080-5-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
we use 'bus->use_posbuf && bus->posbuf.addr' in
hda_dsp_ctrl_init_chip(), use the same for hda_dsp_ctrl_stop_chip()
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20211207193947.71080-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The work-around enabled in hda-stream.c is only required on earlier
versions of SOCs/PCH (Skylake, KabyLake, ApolloLake,
GeminiLake). Before setting the format on the host DMA, it is required
to couple the host and link DMA - which as a consequence shall use the
same format.
This patch introduces a quirk field in the platform descriptor and
makes the work-around conditional. Newer platforms have
no limitations on the use of host and link DMA, which can use
different formats.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Link: https://lore.kernel.org/r/20211207193947.71080-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Move the ICL specific ops to icl.c. Also introduce a
macro ICL_DSP_HPRO_CORE_ID to define the core that
should be powered up when HPRO is enabled.
Reviewed-by: Bard Liao <bard.liao@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20211207193947.71080-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
UCM of Acer Chromebook (Nyan) uses a different name for the headphones
jack. The name was changed during unification of the machine drivers and
UCM fails now to load because of that. Restore the old jack name.
Cc: <stable@vger.kernel.org>
Fixes: cc8f70f ("ASoC: tegra: Unify ASoC machine drivers")
Reported-by: Thomas Graichen <thomas.graichen@gmail.com> # T124 Nyan Big
Tested-by: Thomas Graichen <thomas.graichen@gmail.com> # T124 Nyan Big
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20211211231146.6137-2-digetx@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
UCM of Acer Chromebook (Nyan) uses DAPM switches of headphones and mic
jack. These switches were lost by accident during unification of the
machine drivers, restore them.
Cc: <stable@vger.kernel.org>
Fixes: cc8f70f ("ASoC: tegra: Unify ASoC machine drivers")
Reported-by: Thomas Graichen <thomas.graichen@gmail.com> # T124 Nyan Big
Tested-by: Thomas Graichen <thomas.graichen@gmail.com> # T124 Nyan Big
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20211211231146.6137-1-digetx@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When snd_gf1_mem_xalloc() returns NULL, the current code still leaves
the formerly allocated block.name string but returns an error
immediately. This patch does code-refactoring to move the kstrdup()
call itself into snd_gf1_mem_xalloc() and deals with the resource free
in the helper code by itself for fixing those memory leaks.
Suggested-by: Jaroslav Kysela <perex@perex.cz>
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20211213132444.22385-2-tiwai@suse.de
Link: https://lore.kernel.org/r/20211213141512.27359-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
snd_gf1_mem_xalloc() returns NULL incorrectly when the memory chunk is
allocated in the middle of the chain. This patch corrects the return
value to treat it properly.
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20211213132444.22385-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
kstrdup() returns NULL when some internal memory errors happen, it is
better to check the return value of it. Otherwise, we may not to be able
to catch some memory errors in time.
Signed-off-by: Xiaoke Wang <xkernel.wang@foxmail.com>
Link: https://lore.kernel.org/r/tencent_1E3950293AC22395ACFE99404C985D738309@qq.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Static analysis with scan-build has found an assignment to vp2 that is
never used. It seems that the check on vp->state > 0 should be actually
on vp2->state instead. Fix this.
This dates back to 2002, I found the offending commit from the git
history git://git.kernel.org/pub/scm/linux/kernel/git/tglx/history.git,
commit 91e39521bbf6 ("[PATCH] ALSA patch for 2.5.4")
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211212172025.470367-1-colin.i.king@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Static variables do not need to be initialised to 0, because compiler
will initialise all uninitialised statics to 0. Thus, remove the
unneeded initializations.
Signed-off-by: Jason Wang <wangborong@cdjrlc.com>
Link: https://lore.kernel.org/r/20211212070422.281924-1-wangborong@cdjrlc.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Another collection of small fixes. It's still not quite calm yet,
but nothing looks scary.
ALSA core got a few fixes for covering the issues detected by fuzzer
and the 32bit compat problem of control API, while the rest are all
device-specific small fixes, including the continued fixes for Tegra.
-----BEGIN PGP SIGNATURE-----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=g4gf
-----END PGP SIGNATURE-----
Merge tag 'sound-5.16-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Another collection of small fixes. It's still not quite calm yet, but
nothing looks scary.
ALSA core got a few fixes for covering the issues detected by fuzzer
and the 32bit compat problem of control API, while the rest are all
device-specific small fixes, including the continued fixes for Tegra"
* tag 'sound-5.16-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (23 commits)
ALSA: hda/realtek - Add headset Mic support for Lenovo ALC897 platform
ALSA: usb-audio: Reorder snd_djm_devices[] entries
ALSA: hda/realtek: Fix quirk for TongFang PHxTxX1
ALSA: ctl: Fix copy of updated id with element read/write
ALSA: pcm: oss: Handle missing errors in snd_pcm_oss_change_params*()
ALSA: pcm: oss: Limit the period size to 16MB
ALSA: pcm: oss: Fix negative period/buffer sizes
ASoC: codecs: wsa881x: fix return values from kcontrol put
ASoC: codecs: wcd934x: return correct value from mixer put
ASoC: codecs: wcd934x: handle channel mappping list correctly
ASoC: qdsp6: q6routing: Fix return value from msm_routing_put_audio_mixer
ASoC: SOF: Intel: Retry codec probing if it fails
ASoC: amd: fix uninitialized variable in snd_acp6x_probe()
ASoC: rockchip: i2s_tdm: Dup static DAI template
ASoC: rt5682s: Fix crash due to out of scope stack vars
ASoC: rt5682: Fix crash due to out of scope stack vars
ASoC: tegra: Use normal system sleep for ADX
ASoC: tegra: Use normal system sleep for AMX
ASoC: tegra: Use normal system sleep for Mixer
ASoC: tegra: Use normal system sleep for MVC
...
Dereferncing of_id pointer will result in exception in current
implementation since of_match_device() will assign it to NULL.
Adding NULL check for protection.
Signed-off-by: Ameer Hamza <amhamza.mgc@gmail.com>
Link: https://lore.kernel.org/r/20211207142309.222820-1-amhamza.mgc@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Smatch complains that we might hit the continue path on every iteration
through the loop.
sound/soc/mediatek/mt8195/mt8195-mt6359-rt1019-rt5682.c:831
mt8195_mt6359_rt1019_rt5682_card_late_probe()
error: uninitialized symbol 'sof_comp'.
Initialize "sof_comp" to NULL to silence this warning.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20211208151145.GA29257@kili
Signed-off-by: Mark Brown <broonie@kernel.org>
With a custom .config, the following error is thrown:
ERROR: modpost: "snd_soc_acpi_codec_list"
[sound/soc/amd/snd-acp-config.ko] undefined!
Fix by adding a clear dependency on SND_SOC_ACPI
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20211207192309.43883-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Move rt1015 driver code to common file to be consistent with
rt1011 and rt1015p.
No functional change.
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Yong Zhi <yong.zhi@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20211207192458.44007-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There is a pop noise at the beginning of the capture data.
This patch adds the delay time before stereo1 ADC unmute to fix the pop sound issue.
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Link: https://lore.kernel.org/r/20211208101718.28945-1-shumingf@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Sparse warnings:
sound/soc/intel/boards/sof_maxim_common.c:140:33: error: symbol
'max_98390_dapm_routes' was not declared. Should it be static?
sound/soc/intel/boards/sof_maxim_common.c:156:33: error: symbol
'max_98390_tt_dapm_routes' was not declared. Should it be static?
Fixes: f316c9d9ba ('ASoC: Intel: boards: add max98390 2/4 speakers support')
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20211207211700.115319-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently ALSA sequencer core tries to process the queued events as
much as possible when they become dispatchable. If applications try
to queue too massive events to be processed at the very same timing,
the sequencer core would still try to process such all events, either
in the interrupt context or via some notifier; in either away, it
might be a cause of RCU stall or such problems.
As a potential workaround for those problems, this patch adds the
upper limit of the amount of events to be processed. The remaining
events are processed in the next batch, so they won't be lost.
For the time being, it's limited up to 1000 events per queue, which
should be high enough for any normal usages.
Reported-by: Zqiang <qiang.zhang1211@gmail.com>
Reported-by: syzbot+bb950e68b400ab4f65f8@syzkaller.appspotmail.com
Link: https://lore.kernel.org/r/20211102033222.3849-1-qiang.zhang1211@gmail.com
Link: https://lore.kernel.org/r/20211207165146.2888-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The miXart timer notification is a variable length, and if a hardware
is screwed up, we may access over the actual data size. Let's add a
sanity check and bail out if an invalid value is received.
Link: https://lore.kernel.org/r/20211207153323.27098-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Clang warns:
sound/ppc/beep.c:103:2: warning: unannotated fall-through between switch labels [-Wimplicit-fallthrough]
case SND_TONE: break;
^
sound/ppc/beep.c:103:2: note: insert 'break;' to avoid fall-through
case SND_TONE: break;
^
break;
1 warning generated.
Clang is more pedantic than GCC, which does not warn when failing
through to a case that is just break or return. Clang's version
is more in line with the kernel's own stance in deprecated.rst.
Add athe missing break to silence the warning.
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Link: https://lore.kernel.org/r/20211207110053.695712-1-anders.roxell@linaro.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The mixart_timer_notify structure was larger than could be represented
by the mixart_msg_data array storage. Adjust the size to as large as
possible to fix the warning seen with -Warray-bounds builds:
sound/pci/mixart/mixart_core.c: In function 'snd_mixart_threaded_irq':
sound/pci/mixart/mixart_core.c:447:50: error: array subscript 'struct mixart_timer_notify[0]' is partly outside array bounds of 'u32[128]' {aka 'unsigned int[128]'} [-Werror=array-bounds]
447 | for(i=0; i<notify->stream_count; i++) {
| ^~
sound/pci/mixart/mixart_core.c:328:12: note: while referencing 'mixart_msg_data'
328 | static u32 mixart_msg_data[MSG_DEFAULT_SIZE / 4];
| ^~~~~~~~~~~~~~~
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20211207062941.2413679-1-keescook@chromium.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Merge series from Ariel D'Alessandro <ariel.dalessandro@collabora.com>:
This is a follow up of patchsets:
[RFC patch 0/5] Support BCLK input clock in tlv320aic31xx
[PATCH 0/4] fsl-asoc-card: Add optional dt property for setting mclk-id
Patch "ASoC: fsl-asoc-card: Support fsl,imx-audio-tlv320aic31xx codec"
in "[RFC patch 0/5] Support BCLK input clock in tlv320aic31xx" missed a
Kconfig option. Sending incremental patch fix.
Regards,
Ariel
Ariel D'Alessandro (1):
ASoC: fsl-asoc-card: Add missing Kconfig option for tlv320aic31xx
sound/soc/fsl/Kconfig | 1 +
1 file changed, 1 insertion(+)
--
2.30.2
Merge series from Trevor Wu <trevor.wu@mediatek.com>:
This series of patches adds support for memory-region assignment, so the
access region of DMA engine could be restricted.
Patches are based on broonie tree "for-next" branch.
Trevor Wu (2):
ASoC: mediatek: mt8195: support reserved memory assignment
dt-bindings: mediatek: mt8195: add memory-region property
.../devicetree/bindings/sound/mt8195-afe-pcm.yaml | 8 ++++++++
sound/soc/mediatek/mt8195/mt8195-afe-pcm.c | 7 +++++++
2 files changed, 15 insertions(+)
--
2.18.0
Merge series from Trevor Wu <trevor.wu@mediatek.com>:
This series of patches adds support for RT5682s headset codec in mt8195
machine drivers, and SOF support on card mt8195-mt6359-rt1019-rt5682 is
also included.
Patches are based on broonie tree "for-next" branch.
Changes since v1:
- remove patch3 and patch4 in v1
- add SOF support on card mt8195-mt6359-rt1012-rt5682
- add new propertes to dt-bindings for mt8195-mt6359-rt1019-rt5682
Trevor Wu (4):
ASoC: mediatek: mt8195: add headset codec rt5682s support
dt-bindings: mediatek: mt8195: add model property
ASoC: mediatek: mt8195: add sof support on mt8195-mt6359-rt1019-rt5682
dt-bindings: mediatek: mt8195: add adsp and dai-link property
.../sound/mt8195-mt6359-rt1011-rt5682.yaml | 4 +
.../sound/mt8195-mt6359-rt1019-rt5682.yaml | 14 +
sound/soc/mediatek/Kconfig | 2 +
.../mt8195/mt8195-mt6359-rt1011-rt5682.c | 29 +-
.../mt8195/mt8195-mt6359-rt1019-rt5682.c | 347 +++++++++++++++++-
5 files changed, 370 insertions(+), 26 deletions(-)
--
2.18.0
A relatively large collection of updates, the size is increased quite a
bit by there being some repetitive changes for similar issues that occur
multiple times with both notifying control value changes and runtime PM.
The Rockchip update looks at first glance like a cleanup but fixes
instantiation of the hardware on some systems.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmGuLfMACgkQJNaLcl1U
h9DMbwf/aewIYwfyThs2O5W8Hhn/fxhr8qV6+k08W4dQDjFstUU3meJ9lsWNhb7W
E2OkuZ7vpvIn3I4Z/1ffNTgvVYafwqg/PVnuUiYtEHr46J6kXZkiUta/e4hZzugb
J+CGDf5c8Dy7bev26JAKRLxOoU3NlsS3ed5iV2NGZt0zf77og759NJf5fSnsebXw
ycio8Tnjx15weS0ipl5nXQ74JMQvV5J+6SWQ0favxX2RpGSSekkj7tg5Jsuwx8R0
nRiBrPHelVJqk5THyyiWe7pImeF2QtTcAWqz8IUR7OfWjBpPlTW6n5VVzKhbuLEr
Qws4epxVeyeV4mbks9K2R9VryYFT5Q==
=ufLK
-----END PGP SIGNATURE-----
Merge tag 'asoc-fix-v5.16-rc4' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v5.16
A relatively large collection of updates, the size is increased quite a
bit by there being some repetitive changes for similar issues that occur
multiple times with both notifying control value changes and runtime PM.
The Rockchip update looks at first glance like a cleanup but fixes
instantiation of the hardware on some systems.
In the patch, widgets, routes and dai-link requrird by SOF are included,
and late_probe is introduced for SOF route connection.
Only when adsp phandle could be retrieved from DTS, the SOF related part
of machine driver is executed.
Additionally, supported dai-links could be specified from DTS, so that
we can disable AP side hardware controls when DSP SOF controls the same
audio FE.
Signed-off-by: Trevor Wu <trevor.wu@mediatek.com>
Signed-off-by: YC Hung <yc.hung@mediatek.com>
Link: https://lore.kernel.org/r/20211129141057.12422-4-trevor.wu@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The only usage of acp6x_pdm_dai_ops is to assign its address to the ops
field in the snd_soc_dai_driver struct, which is a pointer to const
snd_soc_dai_ops. Make it const to allow the compiler to put it in
read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Link: https://lore.kernel.org/r/20211204110848.21322-1-rikard.falkeborn@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of double validating of_node, return value of
the boolean property directly.
We can't remove ifdeffery, because in OF_GPIO=n cases
it might bring unwanted surprises.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Link: https://lore.kernel.org/r/20211202205612.76216-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
GPIO library does copy the of_node from the parent device of
the GPIO chip, there is no need to repeat this in the individual
drivers. Remove assignment here.
For the details one may look into the of_gpio_dev_init() implementation.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Link: https://lore.kernel.org/r/20211202205612.76216-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Some of the drivers do not set parent device. This may lead to obstacles
during debugging or understanding the device relations from the Linux
point of view. Assign parent device for GPIO chips created by these
drivers.
While at it, let GPIO library to assign of_node from the parent device.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20211202204838.75287-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Dereferncing of_id pointer will result in exception in current
implementation since of_match_device() will assign it to NULL.
Adding NULL check for protection.
Signed-off-by: Ameer Hamza <amhamza.mgc@gmail.com>
Link: https://lore.kernel.org/r/20211205204200.7852-1-amhamza.mgc@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
mt8195 machine driver adds rt5682s support in this patch.
Card name can be specified from dts by model property, and driver makes
use of the name to distinguish which headset codec is on the board.
Signed-off-by: Trevor Wu <trevor.wu@mediatek.com>
Link: https://lore.kernel.org/r/20211129141057.12422-2-trevor.wu@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The following commit added support for tlv320aic31xx codec to
fsl-asoc-card, but missed the related Kconfig option. Fix this.
commit 8c9b9cfb77
Author: Ariel D'Alessandro <ariel.dalessandro@collabora.com>
Date: Fri Nov 19 12:32:48 2021 -0300
ASoC: fsl-asoc-card: Support fsl,imx-audio-tlv320aic31xx codec
Signed-off-by: Ariel D'Alessandro <ariel.dalessandro@collabora.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Link: https://lore.kernel.org/r/20211203175018.252641-2-ariel.dalessandro@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
For security purpose, restrict the memory assess region of AFE memif.
The specified memory region should be assigned from DTS.
Signed-off-by: Trevor Wu <trevor.wu@mediatek.com>
Link: https://lore.kernel.org/r/20211130053905.28470-2-trevor.wu@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Olivia Mackintosh has posted to alsa-devel reporting that
there's a potential bug that could break mixer quirks for Pioneer
devices introduced by 6d27788160
"ALSA: usb-audio: Add support for the Pioneer DJM 750MK2
Mixer/Soundcard".
This happened because the DJM 750 MK2 was added last to the Pioneer DJM
device table index and defined as 0x4 but was added to snd_djm_devices[]
just after the DJM 750 (MK1) entry instead of last, after the DJM 900
NXS2. This escaped review.
To prevent that from ever happening again, Takashi Iwai suggested to use
C99 array designators in snd_djm_devices[] instead of simply reordering
the entries.
Fixes: 6d27788160 ("ALSA: usb-audio: Add support for the Pioneer DJM 750MK2")
Reported-by: Olivia Mackintosh <livvy@base.nu>
Suggested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Geraldo Nascimento <geraldogabriel@gmail.com>
Link: https://lore.kernel.org/r/Yau46FDzoql0SNnW@geday
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This fixes the SND_PCI_QUIRK(...) of the TongFang PHxTxX1 barebone. This
fixes the issue of sound not working after s3 suspend.
When waking up from s3 suspend the Coef 0x10 is set to 0x0220 instead of
0x0020. Setting the value manually makes the sound work again. This patch
does this automatically.
While being on it, I also fixed the comment formatting of the quirk and
shortened variable and function names.
Signed-off-by: Werner Sembach <wse@tuxedocomputers.com>
Fixes: dd6dd6e3c7 ("ALSA: hda/realtek: Add quirk for TongFang PHxTxX1")
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211202165010.876431-1-wse@tuxedocomputers.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When control_compat.c:copy_ctl_value_to_user() is used, by
ctl_elem_read_user() & ctl_elem_write_user(), it must also copy back the
snd_ctl_elem_id value that may have been updated (filled in) by the call
to snd_ctl_elem_read/snd_ctl_elem_write().
This matches the functionality provided by snd_ctl_elem_read_user() and
snd_ctl_elem_write_user(), via snd_ctl_build_ioff().
Without this, and without making additional calls to snd_ctl_info()
which are unnecessary when using the non-compat calls, a userspace
application will not know the numid value for the element and
consequently will not be able to use the poll/read interface on the
control file to determine which elements have updates.
Signed-off-by: Alan Young <consult.awy@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211202150607.543389-1-consult.awy@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Set SPI_MASTER as dependency as is using CS35L41 SPI driver
Fixes: 96792fdd77 ("ASoC: amd: enable vangogh platform machine driver build")
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/20211201180004.1402156-1-tanureal@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There's a system that reports a bogus HDMI audio interface:
$ cat eld#2.0
monitor_present 1
eld_valid 1
monitor_name
connection_type DisplayPort
eld_version [0x2] CEA-861D or below
edid_version [0x3] CEA-861-B, C or D
manufacture_id 0xe430
product_id 0x690
port_id 0x0
support_hdcp 0
support_ai 0
audio_sync_delay 0
speakers [0xffff] FL/FR LFE FC RL/RR RC FLC/FRC RLC/RRC FLW/FRW FLH/FRH TC FCH
sad_count 0
Since playing audio is not possible without SAD, also consider ELD is
invalid for this case.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Link: https://lore.kernel.org/r/20211202073338.1384768-1-kai.heng.feng@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A couple of calls in snd_pcm_oss_change_params_locked() ignore the
possible errors. Catch those errors and abort the operation for
avoiding further problems.
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211201073606.11660-4-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A collection of small fixes. A large series is found for ASoC
tegra drivers to correct the control element handlings, while
others are mostly for device-specific quirks and fix-ups.
-----BEGIN PGP SIGNATURE-----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=uq+I
-----END PGP SIGNATURE-----
Merge tag 'sound-5.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A collection of small fixes. A large series is found for ASoC tegra
drivers to correct the control element handlings, while others are
mostly for device-specific quirks and fix-ups"
* tag 'sound-5.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (25 commits)
ALSA: hda/hdmi: fix HDA codec entry table order for ADL-P
ALSA: hda: Add Intel DG2 PCI ID and HDMI codec vid
ALSA: hda/cs8409: Set PMSG_ON earlier inside cs8409 driver
ASoC: SOF: hda: reset DAI widget before reconfiguring it
ASoC: cs35l41: Set the max SPI speed for the whole device
ALSA: intel-dsp-config: add quirk for CML devices based on ES8336 codec
ASoC: Intel: soc-acpi: add entry for ESSX8336 on CML
ASoC: rk817: Add module alias for rk817-codec
ASoC: soc-acpi: Set mach->id field on comp_ids matches
ASoC: tegra: Fix kcontrol put callback in Mixer
ASoC: tegra: Fix kcontrol put callback in ADX
ASoC: tegra: Fix kcontrol put callback in AMX
ASoC: tegra: Fix kcontrol put callback in SFC
ASoC: tegra: Fix kcontrol put callback in MVC
ASoC: tegra: Fix kcontrol put callback in AHUB
ASoC: tegra: Fix kcontrol put callback in DSPK
ASoC: tegra: Fix kcontrol put callback in DMIC
ASoC: tegra: Fix kcontrol put callback in I2S
ASoC: tegra: Fix kcontrol put callback in ADMAIF
ASoC: tegra: Fix wrong value type in MVC
...
The MVC module has a per channel control bit, based on which it decides
to apply channel specific volume/mute settings. When per channel control
bit is enabled (which is the default HW configuration), all MVC channel
volume/mute can be independently controlled. If the control is disabled,
channel-0 volume/mute setting is applied by HW to all remaining channels.
Thus add support to leverage this HW feature by exposing master controls
for volume/mute.
With this, now there are per channel and master volume/mute controls.
Users need to just use controls which are suitable for their applications.
The per channel control enable/disable is mananged in driver and hidden
from users, so that they need to just worry about respective volume/mute
controls.
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Link: https://lore.kernel.org/r/1638278605-28225-1-git-send-email-spujar@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
wsa881x_set_port() and wsa881x_put_pa_gain() currently returns zero eventhough
it changes the value. Fix this, so that change notifications are sent
correctly.
Fixes: a0aab9e140 ("ASoC: codecs: add wsa881x amplifier support")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20211130160507.22180-5-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
wcd934x_compander_set() currently returns zero eventhough it changes the value.
Fix this, so that change notifications are sent correctly.
Fixes: 1cde8b8223 ("ASoC: wcd934x: add basic controls")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20211130160507.22180-4-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently each channel is added as list to dai channel list, however
there is danger of adding same channel to multiple dai channel list
which endups corrupting the other list where its already added.
This patch ensures that the channel is actually free before adding to
the dai channel list and also ensures that the channel is on the list
before deleting it.
This check was missing previously, and we did not hit this issue as
we were testing very simple usecases with sequence of amixer commands.
Fixes: a70d924575 ("ASoC: wcd934x: add capture dapm widgets")
Fixes: dd9eb19b56 ("ASoC: wcd934x: add playback dapm widgets")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20211130160507.22180-2-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
msm_routing_put_audio_mixer() can return incorrect value in various scenarios.
scenario 1:
amixer cset iface=MIXER,name='SLIMBUS_0_RX Audio Mixer MultiMedia1' 1
amixer cset iface=MIXER,name='SLIMBUS_0_RX Audio Mixer MultiMedia1' 0
return value is 0 instead of 1 eventhough value was changed
scenario 2:
amixer cset iface=MIXER,name='SLIMBUS_0_RX Audio Mixer MultiMedia1' 1
amixer cset iface=MIXER,name='SLIMBUS_0_RX Audio Mixer MultiMedia1' 1
return value is 1 instead of 0 eventhough the value was not changed
scenario 3:
amixer cset iface=MIXER,name='SLIMBUS_0_RX Audio Mixer MultiMedia1' 0
return value is 1 instead of 0 eventhough the value was not changed
Fix this by adding checks, so that change notifications are sent correctly.
Fixes: e3a33673e8 ("ASoC: qdsp6: q6routing: Add q6routing driver")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20211130163110.5628-1-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix compile error when OSS_DEBUG is enabled:
sound/core/oss/pcm_oss.c: In function 'snd_pcm_oss_set_trigger':
sound/core/oss/pcm_oss.c:2055:10: error: 'substream' undeclared (first
use in this function); did you mean 'csubstream'?
pcm_dbg(substream->pcm, "pcm_oss: trigger = 0x%x\n", trigger);
^
Fixes: 61efcee860 ("ALSA: oss: Use standard printk helpers")
Signed-off-by: Bixuan Cui <cuibixuan@linux.alibaba.com>
Link: https://lore.kernel.org/r/1638349134-110369-1-git-send-email-cuibixuan@linux.alibaba.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
With NHLT enriched with new search functions, remove local code in
favour of them. This also fixes broken behaviour: search should be based
on significant bits count rather than container size.
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20211126140355.1042684-4-cezary.rojewski@intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Don't populate various arrays on the stack but instead make them
static const. Also makes the object code smaller by a few hundred
bytes.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20211129224236.506883-1-colin.i.king@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
These are only assigned to the ops fields in the snd_soc_dai_link struct
which is a pointer to const struct snd_soc_ops. Make them const to allow
the compiler to put them in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20211127091954.12075-1-rikard.falkeborn@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
On my T14s Gen2 I saw the following:
[ 16.057258] skl_hda_dsp_generic skl_hda_dsp_generic: hda_dsp_hdmi_build_controls: no PCM in topology for HDMI converter 3
[ 16.057261] skl_hda_dsp_generic skl_hda_dsp_generic: hda_dsp_hdmi_build_controls: no PCM in topology for HDMI converter 4
[ 16.057263] skl_hda_dsp_generic skl_hda_dsp_generic: hda_dsp_hdmi_build_controls: no PCM in topology for HDMI converter 5
[...and so on.]
It looks like the double newline is a mistake, so remove one.
Signed-off-by: Chris Down <chris@chrisdown.name>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/YaOS0sBueAfApwOx@chrisdown.name
Signed-off-by: Mark Brown <broonie@kernel.org>
These are only assigned to the ops field in the snd_soc_dai_link which
is a pointer to const struct snd_soc_ops. Make them const to allow the
compiler to put them in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Link: https://lore.kernel.org/r/20211127093147.17368-1-rikard.falkeborn@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
On the latest Lenovo Thinkstation laptops, we often experience the
speaker failure after rebooting, check the dmesg, we could see:
sof-audio-pci-intel-tgl 0000:00:1f.3: codec #0 probe error, ret: -5
The analogue codec on the machine is ALC287, then we designed a
testcase to reboot and check the codec probing result repeatedly, we
found the analogue codec probing always failed at least once within
several minutes to several hours (roughly 1 reboot per min). This
issue happens on all laptops of this Thinkstation model, but with
legacy HDA driver, we couldn't reproduce this issue on those laptops.
And so far, this issue is not reproduced on machines which don't
belong to this model.
We tried to make the hda_dsp_ctrl_init_chip() same as
hda_intel_init_chip() which is the controller init routine in the
legacy HDA driver, but it didn't help.
We found when issue happens, the resp is -1, and if we let driver
re-run send_cmd() and get_response(), it will get the correct response
10ec0287, then driver continues the rest work, finally boot to the
desktop and all audio function work well.
Here adding codec probing retries to 3 times, it could fix the issue
on this Thinkstation model, and it doesn't bring impact to other
machines.
Reviewed-by: Bard Liao <bard.liao@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20211130090606.529348-1-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The "index" is potentially used without being initialized on the error
path.
Fixes: fc329c1de4 ("ASoC: amd: add platform devices for acp6x pdm driver and dmic driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20211130125633.GA24941@kili
Signed-off-by: Mark Brown <broonie@kernel.org>
Previously, the DAI template was used directly, which lead to
fun bugs such as "why is my channels_max changing?" when one
instantiated more than one i2s_tdm IP block in a device tree.
This change makes it so that we instead duplicate the template
struct, and then use that.
Fixes: 081068fd64 ("ASoC: rockchip: add support for i2s-tdm controller")
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Link: https://lore.kernel.org/r/20211125084900.417102-1-frattaroli.nicolas@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>:
Current soc_pcm_pointer() is checking runtime->delay,
but it might be updated silently by component's .point callback.
It is strange and difficult to find/know the issue. This patch
adds .delay callback for component, and solve the issue.
HDA uses a timecounter to read a hardware clock running at 24 MHz. The
conversion factor is set with a mult value of 125 and a shift value of 0,
which is not converting the hardware clock to nanoseconds, it is converting
to 1/3 nanoseconds because the conversion factor from 24Mhz to nanoseconds
is 125/3. The usage sites divide the "nanoseconds" value returned by
timecounter_read() by 3 to get a real nanoseconds value.
There is a lengthy comment in azx_timecounter_init() explaining this
choice. That comment makes blatantly wrong assumptions about how
timecounters work and what can overflow.
The comment says:
* Applying the 1/3 factor as part of the multiplication
* requires at least 20 bits for a decent precision, however
* overflows occur after about 4 hours or less, not a option.
timecounters operate on time deltas between two readouts of a clock and use
the mult/shift pair to calculate a precise nanoseconds value:
delta_nsec = (delta_clock * mult) >> shift;
The fractional part is also taken into account and preserved to prevent
accumulated rounding errors. For details see cyclecounter_cyc2ns().
The mult/shift pair has to be chosen so that the multiplication of the
maximum expected delta value does not result in a 64bit overflow. As the
counter wraps around on 32bit, the maximum observable delta between two
reads is (1 << 32) - 1 which is about 178.9 seconds.
That in turn means the maximum multiplication factor which fits into an u32
will not cause a 64bit overflow ever because it's guaranteed that:
((1 << 32) - 1) ^ 2 < (1 << 64)
The resulting correct multiplication factor is 2796202667 and the shift
value is 26, i.e. 26 bit precision. The overflow of the multiplication
would happen exactly at a clock readout delta of 6597069765 which is way
after the wrap around of the hardware clock at around 274.8 seconds which
is off from the claimed 4 hours by more than an order of magnitude.
If the counter ever wraps around the last read value then the calculation
is off by the number of wrap arounds times 178.9 seconds because the
overflow cannot be observed.
Use clocks_calc_mult_shift(), which calculates the most accurate mult/shift
pair based on the given clock frequency, and remove the bogus comment along
with the divisions at the readout sites.
Fixes: 5d890f591d ("ALSA: hda: support for wallclock timestamps")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/871r35kwji.ffs@tglx
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Qcom machine driver adds rt5682s support in this patch.
Card name can be specified from dts by model property, and driver makes
use of the name to distinguish which headset codec is on the board.
Signed-off-by: lvzhaoxiong <lvzhaoxiong@huaqin.corp-partner.google.com>
Link: https://lore.kernel.org/r/20211123024329.21998-1-lvzhaoxiong@huaqin.corp-partner.google.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This allows changing the volume of each digital input/output
independently, and provides the only "master volume" for the DAC.
(The ADC also has a gain control on the analog side.)
While the hardware supports digital gain up to +72dB, the controls here
are limited to +24dB maximum, as any gain above that level makes volume
sliders difficult to use, and is extremely likely to cause clipping.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/r/20211118033645.43524-1-samuel@sholland.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Now ALSA SoC supports .delay for component.
This patch uses it, and not update runtime->delay on .pointer
directly / secretly.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/871r3gy25j.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Now ALSA SoC supports .delay for component.
This patch uses it, and not update runtime->delay on .pointer
directly / secretly.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/8735nwy25o.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Current soc-pcm.c :: soc_pcm_pointer() is assuming that
component driver might update runtime->delay silently in
snd_soc_pcm_component_pointer() (= A).
static snd_pcm_uframes_t soc_pcm_pointer(...)
{
...
/* clearing the previous total delay */
=> runtime->delay = 0;
(A) offset = snd_soc_pcm_component_pointer(substream);
/* base delay if assigned in pointer callback */
=> delay = runtime->delay;
...
}
1) The behavior that ".pointer callback secretly updates
runtime->delay" is strange and confusable.
2) Current snd_soc_pcm_component_pointer() uses 1st found component's
.pointer callback only, thus it is no problem for now.
But runtime->delay might be overwrote if it adjusted to multiple
components in the future.
3) Component delay is updated at .pointer callback timing (secretly).
But some components which doesn't have .pointer callback might want
to increase runtime->delay for some reasons.
We already have .delay function for DAI, but not have for Component.
This patch adds new snd_soc_pcm_component_delay() for it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/874k8cy25t.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Current soc_pcm_pointer() is manually calculating
both CPU-DAI's max delay (= A)
and Codec-DAI's max delay (= B).
static snd_pcm_uframes_t soc_pcm_pointer(...)
{
...
^ for_each_rtd_cpu_dais(rtd, i, cpu_dai)
(A) cpu_delay = max(cpu_delay, ...);
v delay += cpu_delay;
^ for_each_rtd_codec_dais(rtd, i, codec_dai)
(B) codec_delay = max(codec_delay, ...);
v delay += codec_delay;
runtime->delay = delay;
...
}
Current soc_pcm_pointer() and the total delay calculating
is not readable / difficult to understand.
This patch update snd_soc_dai_delay() to snd_soc_pcm_dai_delay(),
and calcule both CPU/Codec delay in one function.
Link: https://lore.kernel.org/r/87fszl4yrq.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/875yssy25z.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
For cs8409, it is required to run Jack Detect on resume.
Jack Detect on cs8409+cs42l42 requires an interrupt from
cs42l42 to be sent to cs8409 which is propogated to the driver
via an unsolicited event.
However, the hda_codec drops unsolicited events if the power_state
is not set to PMSG_ON. Which is set at the end of the resume call.
This means there is a race condition between setting power_state
to PMSG_ON and receiving the interrupt.
To solve this, we can add an API to set the power_state earlier
and call that before we start Jack Detect.
This does not cause issues, since we know inside our driver that
we are already initialized, and ready to handle the unsolicited
events.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Signed-off-by: Vitaly Rodionov <vitalyr@opensource.cirrus.com>
Cc: <stable@vger.kernel.org> # v5.15+
Link: https://lore.kernel.org/r/20211128115558.71683-1-vitalyr@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Merge series from Kai Vehmanen <kai.vehmanen@linux.intel.com>:
Implement an updated programming sequence to handle DMA stop for Intel
HD-Audio DMA.
The new flow is only used if the firmware is sufficiently new to
support the feature. SOF1.9.2 is the first release with the updated
flow. The kernel changes are backwards compatible with old firmware
releases. Likewise new firmware releases will work with old kernel.
Series reviewed originally at:
https://github.com/thesofproject/linux/pull/3167
